As a common fault of the aero-engine,the blade-casing rubbing(BCR)has the potential to cause catastrophic accidents.In this paper,to investigate the dynamic responses and wear characteristics of the system,the laminat...As a common fault of the aero-engine,the blade-casing rubbing(BCR)has the potential to cause catastrophic accidents.In this paper,to investigate the dynamic responses and wear characteristics of the system,the laminated shell element is used to establish the finite element model(FEM)of a flexibly coated casing system.Using the shell element,the blade is modeled,and the surface stress of the blade is calculated.The stress-solving method of the blade is validated through comparisons with the measured time-domain waveform of the stress.Then,a dynamic model of a blade-flexibly coated casing system with rubbing is proposed,accounting for the time-varying mass and stiffness of the casing caused by coating wear.The effects of the proposed flexible casing model are compared with those of a rigid casing model,and the stress changes induced by rubbing are investigated.The results show that the natural characteristics of the coated casing decrease due to the coating wear.The flexibly coated casing model is found to be more suitable for studying casing vibration.Additionally,the stress changes caused by rubbing are slight,and the change in the stress maximum is approximately 5%under the influence of the abrasive coating.展开更多
This paper presents a dynamic modeling method to test and examine the minimum mass of pressurized pore-gas for triggering landslides in stable gentle soil slopes.A stable gentle soil slope model is constructed with a ...This paper presents a dynamic modeling method to test and examine the minimum mass of pressurized pore-gas for triggering landslides in stable gentle soil slopes.A stable gentle soil slope model is constructed with a dry cement powder core,a saturated clay middle layer,and a dry sand upper layer.The test injects H_(2)O_(2)solution into the cement core to produce new pore-gas.The model test includes three identical H_(2)O_(2)injections.The small mass of generated oxygen gas(0.07%of slope soil mass and landslide body)from the first injection can build sufficient pore-gas pressure to cause soil upheaval and slide.Meanwhile,despite the first injection causing leak paths in the clay layer,the generated small mass of gas from the second and third injections can further trigger the landslide.A dynamic theoretical analysis of the slope failure is carried out and the required minimum pore-gas pressure for the landslide is calculated.The mass and pressure of generated gas in the model test are also estimated based on the calibration test for oxygen generation from H_(2)O_(2)solution in cement powder.The results indicate that the minimum mass of the generated gas for triggering the landslide is 2 ppm to 0.07%of the landslide body.Furthermore,the small mass of gas can provide sufficient pressure to cause soil upheaval and soil sliding in dynamic analysis.展开更多
This study aims to develop an accurate calculation model of transmission torque and load-bearing capacity for hydro-viscous clutches(HVC)used in high-power vehicles,which is important to investigate the step-less spee...This study aims to develop an accurate calculation model of transmission torque and load-bearing capacity for hydro-viscous clutches(HVC)used in high-power vehicles,which is important to investigate the step-less speed regulation characteristics in a fan drive system.However,most of the existing models ignore the distribution differences of groove area along the radial direction,which may lead to significant deviations in calculating the mechanical property of friction pairs related to operating conditions and the engagement process.To fill this gap,a new calculation model for bearing capacity and frictional torque of friction pairs with different oil grooves is proposed,in which the traditional fixed contact area ratio coefficient for oil groove measurement is replaced by a more precise discrete micro-ring area ratio(DMAR)integration method.Then,a 32-degree-of-freedoms dynamic model of HVC at a fan drive system is established for the prediction of dynamic responses during speed regulation.Results show that friction pairs with different oil grooves have a direct influence on frictional torque and bearing capacity through the change of DMAR along the radial direction.The friction pairs with different groove structures have oscillation phenomena at the engagement steady-state boundary.Furthermore,a step-less speed regulation experimental setup is established to verify the correctness of the proposed model.It is demonstrated that the axial engagement force and the speed regulation curve predicted by the proposed method are in good agreement with the experimental data.The results could effectively predict the engagement dynamic characteristics.The numerical relationship among the structure parameters,the mechanical properties of friction pairs,and the speed regulation characteristics of the system are established through the proposed model,which lays a theoretical foundation for the structure design of friction plates and optimization of step-less speed regulation performance.展开更多
Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade compone...Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.展开更多
To realize automatic modeling and dynamic simulation of the educational assembling-type robot with open structure, a general dynamic model for the educational assembling-type robot and a fast simulation algorithm are ...To realize automatic modeling and dynamic simulation of the educational assembling-type robot with open structure, a general dynamic model for the educational assembling-type robot and a fast simulation algorithm are put forward. First, the educational robot system is abstracted to a multibody system and a general dynamic model of the educational robot is constructed by the Newton-Euler method. Then the dynamic model is simplified by a combination of components with fixed connections according to the structural characteristics of the educational robot. Secondly, in order to obtain a high efficiency simulation algorithm, based on the sparse matrix technique, the augmentation algorithm and the direct projective constraint stabilization algorithm are improved. Finally, a numerical example is given. The results show that the model and the fast algorithm are valid and effective. This study lays a dynamic foundation for realizing the simulation platform of the educational robot.展开更多
The tangentially fired utility boiler furnace is divided into several sections. The dynamic mathematical models for each section are presented. In the combustion zone, three dimensional model is used, while for the up...The tangentially fired utility boiler furnace is divided into several sections. The dynamic mathematical models for each section are presented. In the combustion zone, three dimensional model is used, while for the upper sections, lumped parameter model is used instead. With the combination of different models, we can get detailed distributions of gas velocity, temperature, chemical species, heat flux, etc. in the furnace, but with less CPU time. The radiation through the interfaces of each section is cons...展开更多
PETREL, a winged hybrid-driven underwater glider is a novel and practical marine survey platform which combines the features of legacy underwater glider and conventional AUV （autonomous underwater vehicle）. It can b...PETREL, a winged hybrid-driven underwater glider is a novel and practical marine survey platform which combines the features of legacy underwater glider and conventional AUV （autonomous underwater vehicle）. It can be treated as a multi-rigid-body system with a floating base and a particular hydrodynamic profile. In this paper, theorems on linear and angular momentum are used to establish the dynamic equations of motion of each rigid body and the effect of translational and rotational motion of internal masses on the attitude control are taken into consideration. In addition, due to the unique external shape with fixed wings and deflectable rudders and the dual-drive operation in thrust and glide modes, the approaches of building dynamic model of conventional AUV and hydrodynamic model of submarine are introduced, and the tailored dynamic equations of the hybrid glider are formulated. Moreover, the behaviors of motion in glide and thrust operation are analyzed based on the simulation and the feasibility of the dynamic model is validated by data from lake field trials.展开更多
There exists a lot of research on the nonlinear vibration of the pipeline system with different boundary conditions.To the best of our knowledge,little research on the actual constraint of the clamp has been performed...There exists a lot of research on the nonlinear vibration of the pipeline system with different boundary conditions.To the best of our knowledge,little research on the actual constraint of the clamp has been performed.In this paper,according to hysteresis loops of the clamp obtained from experimental test,the simplified bilinear stiffness and damping model is proposed.Then the Finite Element(FE)model of L-type pipeline system with clamps is established using Timoshenko beam theory in combination with aforementioned stiffness-damping model.Both hammering and shaker tests verify the FE model via the comparisons of natural frequencies and vibration responses.The results show that the maximum errors of natural frequencies and vibration responses are about 8.31%and 17.6%,respectively.The proposed model can simulate the dynamic characteristics of the L-type pipeline system with clamps well,which is helpful to provide some guidance for the early design stage of pipeline in aero-engine.展开更多
In order to build high accuracy integral dynamic models of cold rolling mill system, by analyzing the vibration process of cold rolling, the dynamic model of 4-h mill, including the rolling process model, the mill rol...In order to build high accuracy integral dynamic models of cold rolling mill system, by analyzing the vibration process of cold rolling, the dynamic model of 4-h mill, including the rolling process model, the mill roll stand structure model and the hydraulic servo system model is built. These three models are coupled and linearized, then the multiple input and multiple output （MIMO） linear transfer function model of single stand 4-h cold mill system is obtained. The model with the proposed data proves its validity, meanwhile the effects of different working conditions on the stability of cold rolling mill system have been discussed. Simulation resulsts show that the model accords with former models and has its own advancement. It contributes to the further study and supression of coupling vibraiton.展开更多
Aiming at handling complicated maneuvers or other unpredicted emergencies for hypersonic glide vehicle tracking,three coupled dynamic models of state estimation based on the priori information between guidance variabl...Aiming at handling complicated maneuvers or other unpredicted emergencies for hypersonic glide vehicle tracking,three coupled dynamic models of state estimation based on the priori information between guidance variables and aerodynamics are presented. Firstly, the aerodynamic acceleration acting on the target is analyzed to reveal the essence of the target’s motion.Then three coupled structures for modeling aerodynamic parameters are developed by different ideas: the spiral model with a harmonic oscillator, the bank model with trigonometric functions of the bank angle and the guide model with the changing rule of guidance variables. Meanwhile, the comparison discussion is concluded to show the novelty and advantage of these models.Finally, a performance assessment in different simulation cases is presented and detailed analysis is revealed. The results show that the proposed models perform excellent properties. Moreover, the guide model produces the best tracking performance and the bank model shows the second; however, the spiral model does not outperform the maneuvering reentry vehicle(MaRV) model markedly.展开更多
This paper combines grey model with time series model and then dynamic model for rapid and in-depth fault prediction in chemical processes. Two combination methods are proposed. In one method, historical data is intro...This paper combines grey model with time series model and then dynamic model for rapid and in-depth fault prediction in chemical processes. Two combination methods are proposed. In one method, historical data is introduced into the grey time series model to predict future trend of measurement values in chemical process. These predicted measurements are then used in the dynamic model to retrieve the change of fault parameters by model based diagnosis algorithm. In another method, historical data is introduced directly into the dynamic model to retrieve historical fault parameters by model based diagnosis algorithm. These parameters are then predicted by the grey time series model. The two methods are applied to a gravity tank example. The case study demonstrates that the first method is more accurate for fault prediction.展开更多
For consideration of both the eccentric rotatable rigid body and the translational rigid body, the dynamic model of the underwater glider is derived. Dynamical behaviors are also studied based on the model and can be ...For consideration of both the eccentric rotatable rigid body and the translational rigid body, the dynamic model of the underwater glider is derived. Dynamical behaviors are also studied based on the model and can be used as the guidance to underwater gliders design. Gibbs function of the underwater glider system is derived first, and then the nonlinear dynamic model is obtained by use of Appell equations. The relationships between dynamic behaviors and design parameters are studied by solving the dynamic model. The spiral motion, swerving motion in three dimensions and the saw-tooth motion of the underwater glider in vertical plane are studied. Lake trials are carried out to validate the dynamic model.展开更多
Cyclic total reflux(CTR) batch distillation is a promising mode of the process but lacking of appropriate modeling for the period of filling the reflux drum.A new dynamic modeling method for the simulation of CTR batc...Cyclic total reflux(CTR) batch distillation is a promising mode of the process but lacking of appropriate modeling for the period of filling the reflux drum.A new dynamic modeling method for the simulation of CTR batch distillation is proposed in this work,in which the changes in column holdup and liquid flow rate during the filling of the drum,and the consequent change in valid number of theoretical plates are considered.The effect of drum holdup on operation time is investigated and the optimal drum holdup is obtained from the simulation.The dynamic modeling is compared to the conventional modeling without consideration of change in liquid flow rate. The experimental result shows that the present modeling is more reliable and more accurate,especially for the column with large liquid holdup.展开更多
Dynamic modeling for incompressible hyperelastic materials with large deformation is an important issue in biomimetic applications. The previously proposed lower-order fully parameterized absolute nodal coordinate for...Dynamic modeling for incompressible hyperelastic materials with large deformation is an important issue in biomimetic applications. The previously proposed lower-order fully parameterized absolute nodal coordinate formulation（ANCF） beam element employs cubic interpolation in the longitudinal direction and linear interpolation in the transverse direction, whereas it cannot accurately describe the large bending deformation. On this account, a novel modeling method for studying the dynamic behavior of nonlinear materials is proposed in this paper. In this formulation, a higher-order beam element characterized by quadratic interpolation in the transverse directions is used in this investigation. Based on the Yeoh model and volumetric energy penalty function, the nonlinear elastic force matrices are derived within the ANCF framework. The feasibility and availability of the Yeoh model are verified through static experiment of nonlinear incompressible materials. Furthermore,dynamic simulation of a silicone cantilever beam under the gravity force is implemented to validate the superiority of the higher-order beam element. The simulation results obtained based on the Yeoh model by employing three different ANCF beam elements are compared with the result achieved from a commercial finite element package as the reference result. It is found that the results acquired utilizing a higher-order beam element are in good agreement with the reference results,while the results obtained using a lower-order beam element are different from the reference results. In addition, the stiffening problem caused by volumetric locking can be resolved effectively by applying a higher-order beam element. It is concluded that the proposed higher-order beam element formulation has satisfying accuracy in simulating dynamic motion process of the silicone beam.展开更多
A nitrogen and phosphorus dynamic model of mesocosm pelagic ecosystem was established according to the summary and synthesis of the models available, in which seven state variables （DIN, PO4-P, DON, DOP, phytoplankto...A nitrogen and phosphorus dynamic model of mesocosm pelagic ecosystem was established according to the summary and synthesis of the models available, in which seven state variables （DIN, PO4-P, DON, DOP, phytoplankton, zooplankton and detritus） were included. Logically it had five modules--phytoplankton, zooplankton, dissolved inorganic nutrients, dissolved organic nutrients and detritus. The results showed that this model could simulate the variations of DIN, PO4-P, DON, DOP, POC and phytoplankton biomass in pelagic ecosystem in mesocosm properly, based on the site experiment data in the Jiaozhou Bay in the autumn of 1999 and the summer of 2000. Not only the logical structure but also the model parameters were feasible, and about 20 parameters were made to fit for the Jiaozhou Bay during the simulation. All of these are necessary to study the control mechanism of nutrients biogeochemical cycling in the Jiaozhou Bay and other China＇ s coastal waters.展开更多
The large capacity servo press is traditionally realized by means of redundant actuation, however there exist the over-constraint problem and interference among actuators, which increases the control difficulty and th...The large capacity servo press is traditionally realized by means of redundant actuation, however there exist the over-constraint problem and interference among actuators, which increases the control difficulty and the product cost. A new type of press mechanism with parallel topology is presented to develop the mechanical servo press with high stamping capacity. The dynamic model considering gravity counterbalance is proposed based on the virtual work principle, and then the effect of counterbalance cylinder on the dynamic performance of the servo press is studied. It is found that the motor torque required to operate the press is a lot less than the others when the ratio of the counterbalance force to the gravity of ram is in the vicinity of 1.0. The stamping force of the real press prototype can reach up to 25 MN on the position of 13 mm away from the bottom dead center. The typical deep-drawing process with 1 200 mm stroke at 8 strokes per minute is proposed by means of five order polynomial. On this process condition, the driving torques are calculated based on the above dynamic model and the torque measuring test is also carried out on the prototype. It is shown that the curve trend of calculation torque is consistent to the measured result and that the average error is less than 15%. The parallel mechanism is introduced into the development of large capacity servo press to avoid the over-constraint and interference of traditional redundant actuation, and its dynamic characteristics with gravity counterbalance are presented.展开更多
Space robotics has been used extensively in complex space missions. Rigid-manipulator space robots may suffer from rigid-body collisions with targets. This collision is likely to cause damage to the space robot and th...Space robotics has been used extensively in complex space missions. Rigid-manipulator space robots may suffer from rigid-body collisions with targets. This collision is likely to cause damage to the space robot and the target. To overcome such a problem, a novel ContinuumManipulator Space Robot(CMSR) for performing on-orbit servicing missions is proposed in this paper. Compared with rigid-manipulator space robots, CMSRs are able to perform compliant operations and avoid rigid-body collisions with a target. The CMSR consists of two kinds of flexible components, including solar arrays and continuum manipulators. The elastic vibrations of these flexible components disturb the position and attitude of CMSRs. The beating phenomenon introduced by the energy transfer among these flexible components can cause damage to solar arrays.The complicated dynamic coupling poses enormous challenges in dynamic modeling and vibration analysis. The dynamic model for CMSRs is derived and the mechanism of the beating phenomenon is analyzed in this paper. Simulation results show that an obvious beating phenomenon occurs and the amplitude of the solar arrays increases significantly when the natural frequencies of two kinds of flexible components are close. A method is provided to avoid the beating phenomenon.展开更多
基金Project supported by the National Science and Technology Major Project(No.J2022-IV-0005-0022)the Aero Science Foundation of China(No.20230015050001)the Shenyang Science and Technology Plan Project of China(No.24-202-6-01)。
文摘As a common fault of the aero-engine,the blade-casing rubbing(BCR)has the potential to cause catastrophic accidents.In this paper,to investigate the dynamic responses and wear characteristics of the system,the laminated shell element is used to establish the finite element model(FEM)of a flexibly coated casing system.Using the shell element,the blade is modeled,and the surface stress of the blade is calculated.The stress-solving method of the blade is validated through comparisons with the measured time-domain waveform of the stress.Then,a dynamic model of a blade-flexibly coated casing system with rubbing is proposed,accounting for the time-varying mass and stiffness of the casing caused by coating wear.The effects of the proposed flexible casing model are compared with those of a rigid casing model,and the stress changes induced by rubbing are investigated.The results show that the natural characteristics of the coated casing decrease due to the coating wear.The flexibly coated casing model is found to be more suitable for studying casing vibration.Additionally,the stress changes caused by rubbing are slight,and the change in the stress maximum is approximately 5%under the influence of the abrasive coating.
基金supported by grants from the Research Grant Council of the Hong Kong Special Administrative Region,China(Project No.HKU 17207518).
文摘This paper presents a dynamic modeling method to test and examine the minimum mass of pressurized pore-gas for triggering landslides in stable gentle soil slopes.A stable gentle soil slope model is constructed with a dry cement powder core,a saturated clay middle layer,and a dry sand upper layer.The test injects H_(2)O_(2)solution into the cement core to produce new pore-gas.The model test includes three identical H_(2)O_(2)injections.The small mass of generated oxygen gas(0.07%of slope soil mass and landslide body)from the first injection can build sufficient pore-gas pressure to cause soil upheaval and slide.Meanwhile,despite the first injection causing leak paths in the clay layer,the generated small mass of gas from the second and third injections can further trigger the landslide.A dynamic theoretical analysis of the slope failure is carried out and the required minimum pore-gas pressure for the landslide is calculated.The mass and pressure of generated gas in the model test are also estimated based on the calibration test for oxygen generation from H_(2)O_(2)solution in cement powder.The results indicate that the minimum mass of the generated gas for triggering the landslide is 2 ppm to 0.07%of the landslide body.Furthermore,the small mass of gas can provide sufficient pressure to cause soil upheaval and soil sliding in dynamic analysis.
基金Supported by the National Natural Science Foundation of China(Grant Nos.52475089,52035002)National Key Research and Development Program of China(Grant No.2021YFB2011400)the Chongqing Natural Science Foundation(Grant No.CSTB2022NSCQ-MSX1243).
文摘This study aims to develop an accurate calculation model of transmission torque and load-bearing capacity for hydro-viscous clutches(HVC)used in high-power vehicles,which is important to investigate the step-less speed regulation characteristics in a fan drive system.However,most of the existing models ignore the distribution differences of groove area along the radial direction,which may lead to significant deviations in calculating the mechanical property of friction pairs related to operating conditions and the engagement process.To fill this gap,a new calculation model for bearing capacity and frictional torque of friction pairs with different oil grooves is proposed,in which the traditional fixed contact area ratio coefficient for oil groove measurement is replaced by a more precise discrete micro-ring area ratio(DMAR)integration method.Then,a 32-degree-of-freedoms dynamic model of HVC at a fan drive system is established for the prediction of dynamic responses during speed regulation.Results show that friction pairs with different oil grooves have a direct influence on frictional torque and bearing capacity through the change of DMAR along the radial direction.The friction pairs with different groove structures have oscillation phenomena at the engagement steady-state boundary.Furthermore,a step-less speed regulation experimental setup is established to verify the correctness of the proposed model.It is demonstrated that the axial engagement force and the speed regulation curve predicted by the proposed method are in good agreement with the experimental data.The results could effectively predict the engagement dynamic characteristics.The numerical relationship among the structure parameters,the mechanical properties of friction pairs,and the speed regulation characteristics of the system are established through the proposed model,which lays a theoretical foundation for the structure design of friction plates and optimization of step-less speed regulation performance.
基金Project supported by the National Natural Science Foundation of China(Nos.12372071 and 12372070)the Aeronautical Science Fund of China(No.2022Z055052001)the Foundation of China Scholarship Council(No.202306830079)。
文摘Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.
基金Hexa-Type Elites Peak Program of Jiangsu Province(No.2008144)Qing Lan Project of Jiangsu ProvinceFund for Excellent Young Teachers of Southeast University
文摘To realize automatic modeling and dynamic simulation of the educational assembling-type robot with open structure, a general dynamic model for the educational assembling-type robot and a fast simulation algorithm are put forward. First, the educational robot system is abstracted to a multibody system and a general dynamic model of the educational robot is constructed by the Newton-Euler method. Then the dynamic model is simplified by a combination of components with fixed connections according to the structural characteristics of the educational robot. Secondly, in order to obtain a high efficiency simulation algorithm, based on the sparse matrix technique, the augmentation algorithm and the direct projective constraint stabilization algorithm are improved. Finally, a numerical example is given. The results show that the model and the fast algorithm are valid and effective. This study lays a dynamic foundation for realizing the simulation platform of the educational robot.
文摘The tangentially fired utility boiler furnace is divided into several sections. The dynamic mathematical models for each section are presented. In the combustion zone, three dimensional model is used, while for the upper sections, lumped parameter model is used instead. With the combination of different models, we can get detailed distributions of gas velocity, temperature, chemical species, heat flux, etc. in the furnace, but with less CPU time. The radiation through the interfaces of each section is cons...
基金supported by the National Natural Science Foundation of China(Grant Nos. 50835006 and 51005161)the Science & Technology Support Planning Foundation of Tianjin(Grant No. 09ZCKFGX03000)the Natural Science Foundation of Tianjin(Grant No. 09JCZDJC23400)
文摘PETREL, a winged hybrid-driven underwater glider is a novel and practical marine survey platform which combines the features of legacy underwater glider and conventional AUV （autonomous underwater vehicle）. It can be treated as a multi-rigid-body system with a floating base and a particular hydrodynamic profile. In this paper, theorems on linear and angular momentum are used to establish the dynamic equations of motion of each rigid body and the effect of translational and rotational motion of internal masses on the attitude control are taken into consideration. In addition, due to the unique external shape with fixed wings and deflectable rudders and the dual-drive operation in thrust and glide modes, the approaches of building dynamic model of conventional AUV and hydrodynamic model of submarine are introduced, and the tailored dynamic equations of the hybrid glider are formulated. Moreover, the behaviors of motion in glide and thrust operation are analyzed based on the simulation and the feasibility of the dynamic model is validated by data from lake field trials.
基金supported by National Natural Science Foundation of China(No.11772089)Fundamental Research Funds for the Central Universities(Nos.N170308028,N170306004 and N180708009)Program for the Innovative Talents of Higher Learning Institutions of Liaoning(LR2017035)。
文摘There exists a lot of research on the nonlinear vibration of the pipeline system with different boundary conditions.To the best of our knowledge,little research on the actual constraint of the clamp has been performed.In this paper,according to hysteresis loops of the clamp obtained from experimental test,the simplified bilinear stiffness and damping model is proposed.Then the Finite Element(FE)model of L-type pipeline system with clamps is established using Timoshenko beam theory in combination with aforementioned stiffness-damping model.Both hammering and shaker tests verify the FE model via the comparisons of natural frequencies and vibration responses.The results show that the maximum errors of natural frequencies and vibration responses are about 8.31%and 17.6%,respectively.The proposed model can simulate the dynamic characteristics of the L-type pipeline system with clamps well,which is helpful to provide some guidance for the early design stage of pipeline in aero-engine.
基金Item Sponsored by National Natural Science Foundation of China(60374032)Beijing Municipal Education Commission Key Discipline Control Theory and Control Engineering of China(XK100080537)
文摘In order to build high accuracy integral dynamic models of cold rolling mill system, by analyzing the vibration process of cold rolling, the dynamic model of 4-h mill, including the rolling process model, the mill roll stand structure model and the hydraulic servo system model is built. These three models are coupled and linearized, then the multiple input and multiple output （MIMO） linear transfer function model of single stand 4-h cold mill system is obtained. The model with the proposed data proves its validity, meanwhile the effects of different working conditions on the stability of cold rolling mill system have been discussed. Simulation resulsts show that the model accords with former models and has its own advancement. It contributes to the further study and supression of coupling vibraiton.
基金supported by the National High-tech R&D Program of China(863 Program)(2015AA7326042 2015AA8321471)
文摘Aiming at handling complicated maneuvers or other unpredicted emergencies for hypersonic glide vehicle tracking,three coupled dynamic models of state estimation based on the priori information between guidance variables and aerodynamics are presented. Firstly, the aerodynamic acceleration acting on the target is analyzed to reveal the essence of the target’s motion.Then three coupled structures for modeling aerodynamic parameters are developed by different ideas: the spiral model with a harmonic oscillator, the bank model with trigonometric functions of the bank angle and the guide model with the changing rule of guidance variables. Meanwhile, the comparison discussion is concluded to show the novelty and advantage of these models.Finally, a performance assessment in different simulation cases is presented and detailed analysis is revealed. The results show that the proposed models perform excellent properties. Moreover, the guide model produces the best tracking performance and the bank model shows the second; however, the spiral model does not outperform the maneuvering reentry vehicle(MaRV) model markedly.
基金Supported by the Shandong Natural Science Foundation(ZR2013BL008)
文摘This paper combines grey model with time series model and then dynamic model for rapid and in-depth fault prediction in chemical processes. Two combination methods are proposed. In one method, historical data is introduced into the grey time series model to predict future trend of measurement values in chemical process. These predicted measurements are then used in the dynamic model to retrieve the change of fault parameters by model based diagnosis algorithm. In another method, historical data is introduced directly into the dynamic model to retrieve historical fault parameters by model based diagnosis algorithm. These parameters are then predicted by the grey time series model. The two methods are applied to a gravity tank example. The case study demonstrates that the first method is more accurate for fault prediction.
基金supported by the National Natural Science Foundation of China (Grant No.50835006)the Natural Science Foundation of Tianjin (Grant No.09JCZDJC23400)
文摘For consideration of both the eccentric rotatable rigid body and the translational rigid body, the dynamic model of the underwater glider is derived. Dynamical behaviors are also studied based on the model and can be used as the guidance to underwater gliders design. Gibbs function of the underwater glider system is derived first, and then the nonlinear dynamic model is obtained by use of Appell equations. The relationships between dynamic behaviors and design parameters are studied by solving the dynamic model. The spiral motion, swerving motion in three dimensions and the saw-tooth motion of the underwater glider in vertical plane are studied. Lake trials are carried out to validate the dynamic model.
文摘Cyclic total reflux(CTR) batch distillation is a promising mode of the process but lacking of appropriate modeling for the period of filling the reflux drum.A new dynamic modeling method for the simulation of CTR batch distillation is proposed in this work,in which the changes in column holdup and liquid flow rate during the filling of the drum,and the consequent change in valid number of theoretical plates are considered.The effect of drum holdup on operation time is investigated and the optimal drum holdup is obtained from the simulation.The dynamic modeling is compared to the conventional modeling without consideration of change in liquid flow rate. The experimental result shows that the present modeling is more reliable and more accurate,especially for the column with large liquid holdup.
基金supported by the National Natural Science Foundation of China (11772186 and 11272203)
文摘Dynamic modeling for incompressible hyperelastic materials with large deformation is an important issue in biomimetic applications. The previously proposed lower-order fully parameterized absolute nodal coordinate formulation（ANCF） beam element employs cubic interpolation in the longitudinal direction and linear interpolation in the transverse direction, whereas it cannot accurately describe the large bending deformation. On this account, a novel modeling method for studying the dynamic behavior of nonlinear materials is proposed in this paper. In this formulation, a higher-order beam element characterized by quadratic interpolation in the transverse directions is used in this investigation. Based on the Yeoh model and volumetric energy penalty function, the nonlinear elastic force matrices are derived within the ANCF framework. The feasibility and availability of the Yeoh model are verified through static experiment of nonlinear incompressible materials. Furthermore,dynamic simulation of a silicone cantilever beam under the gravity force is implemented to validate the superiority of the higher-order beam element. The simulation results obtained based on the Yeoh model by employing three different ANCF beam elements are compared with the result achieved from a commercial finite element package as the reference result. It is found that the results acquired utilizing a higher-order beam element are in good agreement with the reference results,while the results obtained using a lower-order beam element are different from the reference results. In addition, the stiffening problem caused by volumetric locking can be resolved effectively by applying a higher-order beam element. It is concluded that the proposed higher-order beam element formulation has satisfying accuracy in simulating dynamic motion process of the silicone beam.
基金The National Natural Science Foundation of China under contract No. 40490262the State Ocean Administration of China"908"Founda-tion under contract No. 908-02-02-03the Science and Technology Development Plan of Qingdao of China under contract No. 06-2-2-7-nsh
文摘A nitrogen and phosphorus dynamic model of mesocosm pelagic ecosystem was established according to the summary and synthesis of the models available, in which seven state variables （DIN, PO4-P, DON, DOP, phytoplankton, zooplankton and detritus） were included. Logically it had five modules--phytoplankton, zooplankton, dissolved inorganic nutrients, dissolved organic nutrients and detritus. The results showed that this model could simulate the variations of DIN, PO4-P, DON, DOP, POC and phytoplankton biomass in pelagic ecosystem in mesocosm properly, based on the site experiment data in the Jiaozhou Bay in the autumn of 1999 and the summer of 2000. Not only the logical structure but also the model parameters were feasible, and about 20 parameters were made to fit for the Jiaozhou Bay during the simulation. All of these are necessary to study the control mechanism of nutrients biogeochemical cycling in the Jiaozhou Bay and other China＇ s coastal waters.
基金supported by National Science and Technology Major Project of China(Grant Nos.2010ZX04017-013,2010ZX04004-112)National Natural Science Foundation of China(Grant No.51205248)+1 种基金Shanghai Municipal Natural Science Foundation of China(Grant No.12ZR1445200)Doctoral Programs Foundation of Ministry of Education of China(Grant No.20120073120060)
文摘The large capacity servo press is traditionally realized by means of redundant actuation, however there exist the over-constraint problem and interference among actuators, which increases the control difficulty and the product cost. A new type of press mechanism with parallel topology is presented to develop the mechanical servo press with high stamping capacity. The dynamic model considering gravity counterbalance is proposed based on the virtual work principle, and then the effect of counterbalance cylinder on the dynamic performance of the servo press is studied. It is found that the motor torque required to operate the press is a lot less than the others when the ratio of the counterbalance force to the gravity of ram is in the vicinity of 1.0. The stamping force of the real press prototype can reach up to 25 MN on the position of 13 mm away from the bottom dead center. The typical deep-drawing process with 1 200 mm stroke at 8 strokes per minute is proposed by means of five order polynomial. On this process condition, the driving torques are calculated based on the above dynamic model and the torque measuring test is also carried out on the prototype. It is shown that the curve trend of calculation torque is consistent to the measured result and that the average error is less than 15%. The parallel mechanism is introduced into the development of large capacity servo press to avoid the over-constraint and interference of traditional redundant actuation, and its dynamic characteristics with gravity counterbalance are presented.
基金supported by the National Natural Science Foundation of China(Nos.91748203,11922203,11772074)。
文摘Space robotics has been used extensively in complex space missions. Rigid-manipulator space robots may suffer from rigid-body collisions with targets. This collision is likely to cause damage to the space robot and the target. To overcome such a problem, a novel ContinuumManipulator Space Robot(CMSR) for performing on-orbit servicing missions is proposed in this paper. Compared with rigid-manipulator space robots, CMSRs are able to perform compliant operations and avoid rigid-body collisions with a target. The CMSR consists of two kinds of flexible components, including solar arrays and continuum manipulators. The elastic vibrations of these flexible components disturb the position and attitude of CMSRs. The beating phenomenon introduced by the energy transfer among these flexible components can cause damage to solar arrays.The complicated dynamic coupling poses enormous challenges in dynamic modeling and vibration analysis. The dynamic model for CMSRs is derived and the mechanism of the beating phenomenon is analyzed in this paper. Simulation results show that an obvious beating phenomenon occurs and the amplitude of the solar arrays increases significantly when the natural frequencies of two kinds of flexible components are close. A method is provided to avoid the beating phenomenon.
