In liquid rocket engines,regenerative cooling technology is essential for preserving structural integrity under extreme thermal loads.However,non-uniform coolant flow distribution within the cooling channels often lea...In liquid rocket engines,regenerative cooling technology is essential for preserving structural integrity under extreme thermal loads.However,non-uniform coolant flow distribution within the cooling channels often leads to localized overheating,posing serious risks to engine reliability and operational lifespan.This study employs a three-dimensional fluid–thermal coupled numerical model to systematically investigate the influence of geometric parameters-specifically the number of inlets,the number of channels,and inlet manifold configurations-on flow uniformity and thermal distribution in non-pyrolysis zones.Key findings reveal that increasing the number of inlets from one to three significantly enhances flow uniformity,reducing mass flow rate deviation from 1.2%to below 0.3%.However,further increasing the inlets to five yields only marginal improvements indicating diminishing(<0.1%),returns beyond three inlets.Additionally,temperature non-uniformity at the combustion chamber throat decreases by 37%-from 3050 K with 18 channels to 1915 K with 30 channels-highlighting the critical role of channel density in effective thermal regulation.Notably,while higher channel counts improve cooling efficiency,they also result in increased pressure losses of approximately 18%–22%,emphasizing the need to balance thermal performance against hydraulic resistance.An optimal configuration comprising 24 channels and three inlets was identified,providing minimal temperature gradients while maintaining acceptable pressure losses.The inlet manifold structure also plays a pivotal role in determining flow distribution.Configuration 3(Config-3),which features an enlarged manifold and reduced inlet velocity,achieves a 40%reduction in velocity fluctuations compared to Configuration 1(Config-1).This improvement leads to a more uniform mass flow distribution,with a relative standard deviation(RSD)of less than 0.15%.Furthermore,this design effectively mitigates localized hot spots near the nozzle-where temperature gradients are most severe-achieving a reduction of approximately 1135 K.展开更多
The reuse of liquid propellant rocket engines has increased the difficulty of their control and estimation.State and parameter Moving Horizon Estimation(MHE)is an optimization-based strategy that provides the necessar...The reuse of liquid propellant rocket engines has increased the difficulty of their control and estimation.State and parameter Moving Horizon Estimation(MHE)is an optimization-based strategy that provides the necessary information for model predictive control.Despite the many advantages of MHE,long computation time has limited its applications for system-level models of liquid propellant rocket engines.To address this issue,we propose an asynchronous MHE method called advanced-multi-step MHE with Noise Covariance Estimation(amsMHE-NCE).This method computes the MHE problem asynchronously to obtain the states and parameters and can be applied to multi-threaded computations.In the background,the state and covariance estimation optimization problems are computed using multiple sampling times.In real-time,sensitivity is used to quickly approximate state and parameter estimates.A covariance estimation method is developed using sensitivity to avoid redundant MHE problem calculations in case of sensor degradation during engine reuse.The amsMHE-NCE is validated through three cases based on the space shuttle main engine system-level model,and we demonstrate that it can provide more accurate real-time estimates of states and parameters compared to other commonly used estimation methods.展开更多
The thermal protection of rocket engines is a crucial aspect of rocket engine design.In this paper,the gas film/regenerative composite cooling of the liquid oxygen/liquid methane(LOX/LCH4)rocket engine thrust chamber ...The thermal protection of rocket engines is a crucial aspect of rocket engine design.In this paper,the gas film/regenerative composite cooling of the liquid oxygen/liquid methane(LOX/LCH4)rocket engine thrust chamber was investigated.A gas film/regenerative composite cooling model was developed based on the Grisson gas film cooling efficiency formula and the one-dimensional regenerative cooling model.The accuracy of the model was validated through experiments conducted on a 6 kg/s level gas film/regenerative composite cooling thrust chamber.Additionally,key parameters related to heat transfer performance were calculated.The results demonstrate that the model is sufficiently accurate to be used as a preliminary design tool.The temperature rise error of the coolant,when compared with the experimental results,was found to be less than 10%.Although the pressure drop error is relatively large,the calculated results still provide valuable guidance for heat transfer analysis.In addition,the performance of composite cooling is observed to be superior to regenerative cooling.Increasing the gas film flow rate results in higher cooling efficiency and a lower gas-side wall temperature.Furthermore,the position at which the gas film is introduced greatly impacts the cooling performance.The optimal introduction position for the gas film is determined when the film is introduced from a single row of holes.This optimal introduction position results in a more uniform wall temperature distribution and reduces the peak temperature.Lastly,it is observed that a double row of holes,when compared to a single row of holes,enhances the cooling effect in the superposition area of the gas film and further lowers the gas-side wall temperature.These results provide a basis for the design of gas film/regenerative composite cooling systems.展开更多
As the core of the rocket system,the performance and quality of rocket engines are of paramount impor-tance.Currently,the production of aerospace model rocket engines does not differentiate the production and selectio...As the core of the rocket system,the performance and quality of rocket engines are of paramount impor-tance.Currently,the production of aerospace model rocket engines does not differentiate the production and selection of motors according to the importance of the mission,which is insufficient to ensure the high reliability requirements of important launch missions.To select rocket engines with better performance quality for more critical launch missions,this paper uses fuzzy comprehensive evaluation and TOPSIS methods based on the test value or assessment informa-tion of evaluation indicators.The method scientifically and accurately ranks the performance quality of rocket engines,choosing the engines with better performance quality for more strategic missions,and providing technical support for national management decisions.展开更多
To investigate the damage localization effects of the thrust chamber wall caused by combustions in LOX/methane rocket engines, a fluid-structural coupling computational methodology with a multi-channel model is develo...To investigate the damage localization effects of the thrust chamber wall caused by combustions in LOX/methane rocket engines, a fluid-structural coupling computational methodology with a multi-channel model is developed to obtain 3-demensioanl thermal and structural responses.Heat and mechanical loads are calculated by a validated finite volume fluid-thermal coupling numerical method considering non-premixed combustion processes of propellants. The methodology is subsequently performed on an LOX/methane thrust chamber under cyclic operation. Results show that the heat loads of the thrust chamber wall are apparently non-uniform in the circumferential direction. There are noticeable disparities between different cooling channels in terms of temperature and strain distributions at the end of the hot run phase, which in turn leads to different temperature ranges, strain ranges, and residual strains during one cycle. With the work cycle proceeding, the circumferential localization effect of the residual strain would be significantly enhanced. A post-processing damage analysis reveals that the low-cycle fatigue damage accumulated in each cycle is almost unchanged, while the quasi static damage accumulated in a considered cycle declines until stabilized after several cycles. The maximum discrepancy of the predicted lives between different cooling channels is about 30%.展开更多
The PDRE test model used in these experiments utilized kerosene as the fuel, oxygen as oxidizer, and nitrogen as purge gas. The solenoid valves were employed to control intermittent supplies of kerosene, oxygen and pu...The PDRE test model used in these experiments utilized kerosene as the fuel, oxygen as oxidizer, and nitrogen as purge gas. The solenoid valves were employed to control intermittent supplies of kerosene, oxygen and purge gas. PDRE test model was 50 mm in inner diameter by 1.2 m long. The DDT （deflagration to detonation transition） enhancement device Shchelkin spiral was used in the test model. The effects of detonation frequency on its time-averaged thrust and specific impulse were experimentally investigated. The obtained results showes that the time-averaged thrust of PDRE test model was approximately proportional to the detonation frequency. For the detonation frequency 20 Hz, the time-averaged thrust was around 107 N, and the specific impulse was around 125 s. The nozzle experiments were conducted using PDRE test model with three traditional nozzles. The experimental results obtained demonstrated that all of those nozzles could augment the thrust and specific impulse. Among those three nozzles, the convergent nozzle had the largest increased augmentation, which was approximately 18%, under the specific condition of the experiment.展开更多
The pulse detonation rocket engine （PDRE） requires periodic supply of oxidizer, fuel and purge gas. A rotary-valve assembly is fabricated to control the periodic supply in this research. Oxygen and liquid aviation k...The pulse detonation rocket engine （PDRE） requires periodic supply of oxidizer, fuel and purge gas. A rotary-valve assembly is fabricated to control the periodic supply in this research. Oxygen and liquid aviation kerosene are used as oxidizer and fuel respectively. An ordinary automobile spark plug, with ignition energy as low as 50 mJ, is used to initiate combustion. Steady operation of the PDRE is achieved with operating frequency ranging from 1 Hz to 10 Hz. Experimentally measured pressure is lower than theoretical value by 13% at 1 Hz and 37% at 10 Hz, and there also exists a velocity deficit at different operating frequencies. Both of these two phenomena are believed mainly due to droplet size which depends on atomization and vaporiza-tion of liquid fuel.展开更多
This paper presents a method of thermal state calculation of combustion chamber in small thrust liquid rocket engine. The goal is to predict the thermal state of chamber wall by using basic parameters of engine: thrus...This paper presents a method of thermal state calculation of combustion chamber in small thrust liquid rocket engine. The goal is to predict the thermal state of chamber wall by using basic parameters of engine: thrust level, propellants, chamber pressure, injection pattern, film cooling parameters, material of wall and their coating, etc. The difficulties in modeling the startup and shutdown processes of thrusters lie in the fact that there are the conjugated physical processes occurring at various parameters for non-design conditions. A mathematical model to predict the thermal state of the combustion chamber for different engine operation modes is developed. To simulate the startup and shutdown processes, a quasi-steady approach is applied by replacing the transient process with time-variant operating parameters of steady-state processes. The mathematical model is based on several principles and data commonly used for heat transfer modeling: geometry of flow part, gas dynamics of flow, thermodynamics of propellants and combustion spices, convective and radiation heat flows, conjugated heat transfer between hot gas and wall, and transient approach for calculation of thermal state of construction. Calculations of the thermal state of the combustion chamber in single-turn-on mode show good convergence with the experimental results. The results of pulsed modes indicate a large temperature gradient on the internal wall surface of the chamber between pulses and the thermal state of the wall strongly depends on the pulse duration and the interval.展开更多
To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a ...To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Structural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter c3= 0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when c3〉 0.The results of sensitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.展开更多
An experiment for rocket engine inducer cavitating flow is conducted on a new experimental platform.The experiment platform,using water as working medium,can be used to investigate the steady and unsteady flows of cav...An experiment for rocket engine inducer cavitating flow is conducted on a new experimental platform.The experiment platform,using water as working medium,can be used to investigate the steady and unsteady flows of cavitating and noncavitating turbopumps.The experimental platform is designed as a flexible and versatile apparatus for any kind of fluid dynamic phenomena relating to high performance liquid rocket engine turbopumps.Design details for the platform is introduced.Various extend of cavitation images and dynamic pressure impulse are obtained,which provides a reference for cavitating flow study in rocket engine inducer.展开更多
Reusable rocket engines are the core components of reusable launch vehicles, and have thus become a major focus of aerospace engineering research in recent years. In practice, subsystem design is based on the overall ...Reusable rocket engines are the core components of reusable launch vehicles, and have thus become a major focus of aerospace engineering research in recent years. In practice, subsystem design is based on the overall index allocation of an engine;therefore, a multidisciplinary optimization approach is necessary. In this study, design of a reusable methane/liquid oxygen(LOX/CH4)rocket engine with a gas generator cycle was investigated using multidisciplinary optimization. Two parameters were chosen as design variables: pressure and fuel mix ratio of the main combustion chamber. Optimization objectives were specific impulse, structural mass, and life cycle cost of the reusable rocket engine, and constraints were assigned to each discipline according to rocket design requirements. Then, an optimization model was developed, and optimal design parameters were acquired for the LOX/CH4 rocket engine. The proposed method is effective for designing the index allocation of reusable rocket engines and takes into account the multidisciplinary nature of complex systems.展开更多
To predict the effect of the liquid rocket engine combustion chamber conditions on the impingement spray, the conventional uncoupled spray model for impinging injectors is extended by considering the coupling of the j...To predict the effect of the liquid rocket engine combustion chamber conditions on the impingement spray, the conventional uncoupled spray model for impinging injectors is extended by considering the coupling of the jet impingement process and the ambient gas field. The new coupled model consists of the plain-orifice sub-model, the jet-jet impingement sub-model and the droplet collision sub-model. The parameters of the child droplet are determined with the jet-jet impingement sub-model using correlations about the liquid jet parameters and the chamber conditions.The overall model is benchmarked under various impingement angles, jet momentum and offcenter ratios. Agreement with the published experimental data validates the ability of the model to predict the key spray characteristics, such as the mass flux and mixture ratio distributions in quiescent air. Besides, impinging sprays under changing ambient pressure and non-uniform gas flow are investigated to explore the effect of liquid rocket engine chamber conditions. First, a transient impingement spray during engine start-up phase is simulated with prescribed pressure profile. The minimum average droplet diameter is achieved when the orifices work in cavitation state, and is about 30% smaller than the steady single phase state. Second, the effect of non-uniform gas flow produces off-center impingement and the rotated spray fan by 38°. The proposed model suggests more reasonable impingement spray characteristics than the uncoupled one and can be used as the first step in the complex simulation of coupling impingement spray and combustion in liquid rocket engines.展开更多
A 500 N model engine filled with LO2/GCH4 was designed and manufactured.A series of ignition attempts were performed in it by both head spark plug and body spark plug.Results show that the engine can be ignited but th...A 500 N model engine filled with LO2/GCH4 was designed and manufactured.A series of ignition attempts were performed in it by both head spark plug and body spark plug.Results show that the engine can be ignited but the combustion cannot be sustained when head spark plug applied as the plug tip was set in the gaseous low-velocity zone with thin spray.This is mainly because flame from this zone cannot supply enough ignition energy for the whole chamber.However,reliable ignition and stable combustion can be achieved by body spark plug.As the O/F ratio increases from 2.61 to 3.49,chamber pressure increases from 0.474 to 0.925 MPa and combustion efficiency increases from 57.8%to 95.1%.This is determined by the injector configuration,which cannot produce the sufficiently breakup of the liquid oxygen on the low flow rate case.展开更多
This paper provides a detailed introduction to and analysis of the course of China's technological innovation in liquid hydrogen/liquid oxygen(LH2/LOX)rocket engines from a historical point of view.It starts with ...This paper provides a detailed introduction to and analysis of the course of China's technological innovation in liquid hydrogen/liquid oxygen(LH2/LOX)rocket engines from a historical point of view.It starts with the investigation of LH2/LOX rocket engines by relevant departments of the Chinese Academy of Sciences in the 1960s and their preliminary achievements.Then,the policy decision concerning LH2/LOX engine development,the project approval of the Long March-3(Chang Zheng-3,CZ-3)rocket,and the process of developing LH2/LOX engines are analyzed in detail,followed by an introduction to and summary of the development situation and technical innovation characteristics of China's LH2/LOX engines as they grew from 4 tons to 8 tons,and finally to 50 tons.Finally,the paper briefly analyzes the innovation experience connected with China's LH2/LOX engines.展开更多
Numerical 2D simulation and research on internal flow field and external flow field of rocket motor nozzle using FLUENT software. Analyze the flow condition of internal flow field and external flow field, and accordin...Numerical 2D simulation and research on internal flow field and external flow field of rocket motor nozzle using FLUENT software. Analyze the flow condition of internal flow field and external flow field, and according to add in the amount of the different gas components, obtain the clear distribution of contour of density flow field, pressure flow field and various material components and so on. Simulation results agree with the results observed from the test on the ground, and provide reference for solid rocket motor development.展开更多
Liquid propellant rocket engines for a launch vehicle are an essential aerospace technology, representing the advanced level of hi-tech in a country. In recent years, China’s aerospace industry has made remarkable ac...Liquid propellant rocket engines for a launch vehicle are an essential aerospace technology, representing the advanced level of hi-tech in a country. In recent years, China’s aerospace industry has made remarkable achievements, and liquid rocket engine technology has also been effectively developed. In this article, the development processes of China’s liquid rocket engines are discussed. Then, the performance features of China’s new generation liquid rocket engines as well as the flight tests of the new-generation launch vehicles are introduced. Finally, the development direction and the most recent progress of the next generation large-thrust liquid rocket engine is presented.展开更多
Based on current research,the development trend of reusable liquid rocket engines was analyzed.Key technologies and research focuses of the reusable liquid rocket engine have been analyzed and summarized,and then sugg...Based on current research,the development trend of reusable liquid rocket engines was analyzed.Key technologies and research focuses of the reusable liquid rocket engine have been analyzed and summarized,and then suggestions on the development of future key technologies are proposed.展开更多
Safety analysis for liquid rocket engine has a great meaning for shortening development cycle, saving development expenditure and reducing development risk. The relationship between the structure and component of liqu...Safety analysis for liquid rocket engine has a great meaning for shortening development cycle, saving development expenditure and reducing development risk. The relationship between the structure and component of liquid rocket engine is much more complex, furthermore test data are absent in development phase. Thereby, the uncertainties exist in safety analysis for liquid rocket engine. A safety analysis model integrated with FMEA(failure mode and effect analysis) based on Bayesian networks (BN) is brought forward for liquid rocket engine, which can combine qualitative analysis with quantitative decision. The method has the advantages of fusing multi-information, saving sample amount and having high veracity. An example shows that the method is efficient.展开更多
The ablative material is supposed to be one of good candidates for LRE （liquid rocket engine） combustion chamber to achieve both high reliability and low cost and a numerical analysis for the ablator is considered t...The ablative material is supposed to be one of good candidates for LRE （liquid rocket engine） combustion chamber to achieve both high reliability and low cost and a numerical analysis for the ablator is considered to be a potentially efficient tool to reduce cost as well. So far, ablators have been successfully applied for many SRM （solid rocket motors）, but the application to LRE is still quite limited in Japan. The authors believe that this is primarily because of the unpredictable nature of the heat load from combustion gases to the combustor wall. Indeed, reliable thermal design of ablative combustion chamber, namely reliable prediction of thermal performance, needs both reliable heat load model and reliable ablator response model. This paper elaborates our research activities and our recent research findings.展开更多
An electro-hydraulic actuator for the thrust vector control(TVC)of a throttlable kerolox rocket engine is introduced in this paper.The creative feature is an integrated hydraulic power drive unit,where a constant spee...An electro-hydraulic actuator for the thrust vector control(TVC)of a throttlable kerolox rocket engine is introduced in this paper.The creative feature is an integrated hydraulic power drive unit,where a constant speed kerosene motor is used to draw high pressure kerosene from the engine and to drive a constant pressure variable displacement piston pump,acting as the power supply for the actuator.Its operational mechanism,to accommodate the varying pressure from the turbo-pump of a throttling engine,lies in a pressure-reducing flow regulator inserted at the motor inlet.Another key point is that the displacement of the motor is reasonably bigger than the pump so that a sufficiently wide range of pressures can be adapted.Modeling analysis and flight test results were well matched,which show the outstanding performance of this novel type actuator.展开更多
基金supported by the Key project of Hunan Provincial Education Department(Grant Number:22A0485)The Natural Science Foundation of Hunan(Grant Number:2024JJ5293)The Key project of Hunan University of Arts and Science(Grant Number:23ZZ08).
文摘In liquid rocket engines,regenerative cooling technology is essential for preserving structural integrity under extreme thermal loads.However,non-uniform coolant flow distribution within the cooling channels often leads to localized overheating,posing serious risks to engine reliability and operational lifespan.This study employs a three-dimensional fluid–thermal coupled numerical model to systematically investigate the influence of geometric parameters-specifically the number of inlets,the number of channels,and inlet manifold configurations-on flow uniformity and thermal distribution in non-pyrolysis zones.Key findings reveal that increasing the number of inlets from one to three significantly enhances flow uniformity,reducing mass flow rate deviation from 1.2%to below 0.3%.However,further increasing the inlets to five yields only marginal improvements indicating diminishing(<0.1%),returns beyond three inlets.Additionally,temperature non-uniformity at the combustion chamber throat decreases by 37%-from 3050 K with 18 channels to 1915 K with 30 channels-highlighting the critical role of channel density in effective thermal regulation.Notably,while higher channel counts improve cooling efficiency,they also result in increased pressure losses of approximately 18%–22%,emphasizing the need to balance thermal performance against hydraulic resistance.An optimal configuration comprising 24 channels and three inlets was identified,providing minimal temperature gradients while maintaining acceptable pressure losses.The inlet manifold structure also plays a pivotal role in determining flow distribution.Configuration 3(Config-3),which features an enlarged manifold and reduced inlet velocity,achieves a 40%reduction in velocity fluctuations compared to Configuration 1(Config-1).This improvement leads to a more uniform mass flow distribution,with a relative standard deviation(RSD)of less than 0.15%.Furthermore,this design effectively mitigates localized hot spots near the nozzle-where temperature gradients are most severe-achieving a reduction of approximately 1135 K.
基金supported by the National Natural Science Foundation of China(Nos.62120106003 and 62173301)。
文摘The reuse of liquid propellant rocket engines has increased the difficulty of their control and estimation.State and parameter Moving Horizon Estimation(MHE)is an optimization-based strategy that provides the necessary information for model predictive control.Despite the many advantages of MHE,long computation time has limited its applications for system-level models of liquid propellant rocket engines.To address this issue,we propose an asynchronous MHE method called advanced-multi-step MHE with Noise Covariance Estimation(amsMHE-NCE).This method computes the MHE problem asynchronously to obtain the states and parameters and can be applied to multi-threaded computations.In the background,the state and covariance estimation optimization problems are computed using multiple sampling times.In real-time,sensitivity is used to quickly approximate state and parameter estimates.A covariance estimation method is developed using sensitivity to avoid redundant MHE problem calculations in case of sensor degradation during engine reuse.The amsMHE-NCE is validated through three cases based on the space shuttle main engine system-level model,and we demonstrate that it can provide more accurate real-time estimates of states and parameters compared to other commonly used estimation methods.
基金supported by the National Science Fund Project(No.2019-JCJQ-ZQ-019)the Innovative Research Group Project of National Natural Science Foundation of China(No.T2221002).
文摘The thermal protection of rocket engines is a crucial aspect of rocket engine design.In this paper,the gas film/regenerative composite cooling of the liquid oxygen/liquid methane(LOX/LCH4)rocket engine thrust chamber was investigated.A gas film/regenerative composite cooling model was developed based on the Grisson gas film cooling efficiency formula and the one-dimensional regenerative cooling model.The accuracy of the model was validated through experiments conducted on a 6 kg/s level gas film/regenerative composite cooling thrust chamber.Additionally,key parameters related to heat transfer performance were calculated.The results demonstrate that the model is sufficiently accurate to be used as a preliminary design tool.The temperature rise error of the coolant,when compared with the experimental results,was found to be less than 10%.Although the pressure drop error is relatively large,the calculated results still provide valuable guidance for heat transfer analysis.In addition,the performance of composite cooling is observed to be superior to regenerative cooling.Increasing the gas film flow rate results in higher cooling efficiency and a lower gas-side wall temperature.Furthermore,the position at which the gas film is introduced greatly impacts the cooling performance.The optimal introduction position for the gas film is determined when the film is introduced from a single row of holes.This optimal introduction position results in a more uniform wall temperature distribution and reduces the peak temperature.Lastly,it is observed that a double row of holes,when compared to a single row of holes,enhances the cooling effect in the superposition area of the gas film and further lowers the gas-side wall temperature.These results provide a basis for the design of gas film/regenerative composite cooling systems.
文摘As the core of the rocket system,the performance and quality of rocket engines are of paramount impor-tance.Currently,the production of aerospace model rocket engines does not differentiate the production and selection of motors according to the importance of the mission,which is insufficient to ensure the high reliability requirements of important launch missions.To select rocket engines with better performance quality for more critical launch missions,this paper uses fuzzy comprehensive evaluation and TOPSIS methods based on the test value or assessment informa-tion of evaluation indicators.The method scientifically and accurately ranks the performance quality of rocket engines,choosing the engines with better performance quality for more strategic missions,and providing technical support for national management decisions.
文摘To investigate the damage localization effects of the thrust chamber wall caused by combustions in LOX/methane rocket engines, a fluid-structural coupling computational methodology with a multi-channel model is developed to obtain 3-demensioanl thermal and structural responses.Heat and mechanical loads are calculated by a validated finite volume fluid-thermal coupling numerical method considering non-premixed combustion processes of propellants. The methodology is subsequently performed on an LOX/methane thrust chamber under cyclic operation. Results show that the heat loads of the thrust chamber wall are apparently non-uniform in the circumferential direction. There are noticeable disparities between different cooling channels in terms of temperature and strain distributions at the end of the hot run phase, which in turn leads to different temperature ranges, strain ranges, and residual strains during one cycle. With the work cycle proceeding, the circumferential localization effect of the residual strain would be significantly enhanced. A post-processing damage analysis reveals that the low-cycle fatigue damage accumulated in each cycle is almost unchanged, while the quasi static damage accumulated in a considered cycle declines until stabilized after several cycles. The maximum discrepancy of the predicted lives between different cooling channels is about 30%.
基金National Natural Science Foundation of China (501- 06012, 50336030)Program for New Century Excellent Talents in Uni-versity(NCET-04-0960)
文摘The PDRE test model used in these experiments utilized kerosene as the fuel, oxygen as oxidizer, and nitrogen as purge gas. The solenoid valves were employed to control intermittent supplies of kerosene, oxygen and purge gas. PDRE test model was 50 mm in inner diameter by 1.2 m long. The DDT （deflagration to detonation transition） enhancement device Shchelkin spiral was used in the test model. The effects of detonation frequency on its time-averaged thrust and specific impulse were experimentally investigated. The obtained results showes that the time-averaged thrust of PDRE test model was approximately proportional to the detonation frequency. For the detonation frequency 20 Hz, the time-averaged thrust was around 107 N, and the specific impulse was around 125 s. The nozzle experiments were conducted using PDRE test model with three traditional nozzles. The experimental results obtained demonstrated that all of those nozzles could augment the thrust and specific impulse. Among those three nozzles, the convergent nozzle had the largest increased augmentation, which was approximately 18%, under the specific condition of the experiment.
基金National Natural Science Foundation of China (50976094)Doctoral Program Foundation of Education Ministry of China (20096102110022)+1 种基金Doctorate Foundation of Northwestern Polytechnical University (CX201112)Graduate Innovation Lab Center of Northwestern Polytechnical University (10006,10013)
文摘The pulse detonation rocket engine （PDRE） requires periodic supply of oxidizer, fuel and purge gas. A rotary-valve assembly is fabricated to control the periodic supply in this research. Oxygen and liquid aviation kerosene are used as oxidizer and fuel respectively. An ordinary automobile spark plug, with ignition energy as low as 50 mJ, is used to initiate combustion. Steady operation of the PDRE is achieved with operating frequency ranging from 1 Hz to 10 Hz. Experimentally measured pressure is lower than theoretical value by 13% at 1 Hz and 37% at 10 Hz, and there also exists a velocity deficit at different operating frequencies. Both of these two phenomena are believed mainly due to droplet size which depends on atomization and vaporiza-tion of liquid fuel.
文摘This paper presents a method of thermal state calculation of combustion chamber in small thrust liquid rocket engine. The goal is to predict the thermal state of chamber wall by using basic parameters of engine: thrust level, propellants, chamber pressure, injection pattern, film cooling parameters, material of wall and their coating, etc. The difficulties in modeling the startup and shutdown processes of thrusters lie in the fact that there are the conjugated physical processes occurring at various parameters for non-design conditions. A mathematical model to predict the thermal state of the combustion chamber for different engine operation modes is developed. To simulate the startup and shutdown processes, a quasi-steady approach is applied by replacing the transient process with time-variant operating parameters of steady-state processes. The mathematical model is based on several principles and data commonly used for heat transfer modeling: geometry of flow part, gas dynamics of flow, thermodynamics of propellants and combustion spices, convective and radiation heat flows, conjugated heat transfer between hot gas and wall, and transient approach for calculation of thermal state of construction. Calculations of the thermal state of the combustion chamber in single-turn-on mode show good convergence with the experimental results. The results of pulsed modes indicate a large temperature gradient on the internal wall surface of the chamber between pulses and the thermal state of the wall strongly depends on the pulse duration and the interval.
文摘To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Structural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter c3= 0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when c3〉 0.The results of sensitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.
文摘An experiment for rocket engine inducer cavitating flow is conducted on a new experimental platform.The experiment platform,using water as working medium,can be used to investigate the steady and unsteady flows of cavitating and noncavitating turbopumps.The experimental platform is designed as a flexible and versatile apparatus for any kind of fluid dynamic phenomena relating to high performance liquid rocket engine turbopumps.Design details for the platform is introduced.Various extend of cavitation images and dynamic pressure impulse are obtained,which provides a reference for cavitating flow study in rocket engine inducer.
文摘Reusable rocket engines are the core components of reusable launch vehicles, and have thus become a major focus of aerospace engineering research in recent years. In practice, subsystem design is based on the overall index allocation of an engine;therefore, a multidisciplinary optimization approach is necessary. In this study, design of a reusable methane/liquid oxygen(LOX/CH4)rocket engine with a gas generator cycle was investigated using multidisciplinary optimization. Two parameters were chosen as design variables: pressure and fuel mix ratio of the main combustion chamber. Optimization objectives were specific impulse, structural mass, and life cycle cost of the reusable rocket engine, and constraints were assigned to each discipline according to rocket design requirements. Then, an optimization model was developed, and optimal design parameters were acquired for the LOX/CH4 rocket engine. The proposed method is effective for designing the index allocation of reusable rocket engines and takes into account the multidisciplinary nature of complex systems.
文摘To predict the effect of the liquid rocket engine combustion chamber conditions on the impingement spray, the conventional uncoupled spray model for impinging injectors is extended by considering the coupling of the jet impingement process and the ambient gas field. The new coupled model consists of the plain-orifice sub-model, the jet-jet impingement sub-model and the droplet collision sub-model. The parameters of the child droplet are determined with the jet-jet impingement sub-model using correlations about the liquid jet parameters and the chamber conditions.The overall model is benchmarked under various impingement angles, jet momentum and offcenter ratios. Agreement with the published experimental data validates the ability of the model to predict the key spray characteristics, such as the mass flux and mixture ratio distributions in quiescent air. Besides, impinging sprays under changing ambient pressure and non-uniform gas flow are investigated to explore the effect of liquid rocket engine chamber conditions. First, a transient impingement spray during engine start-up phase is simulated with prescribed pressure profile. The minimum average droplet diameter is achieved when the orifices work in cavitation state, and is about 30% smaller than the steady single phase state. Second, the effect of non-uniform gas flow produces off-center impingement and the rotated spray fan by 38°. The proposed model suggests more reasonable impingement spray characteristics than the uncoupled one and can be used as the first step in the complex simulation of coupling impingement spray and combustion in liquid rocket engines.
基金Project(613239)supported by the National Basic Research Program of China
文摘A 500 N model engine filled with LO2/GCH4 was designed and manufactured.A series of ignition attempts were performed in it by both head spark plug and body spark plug.Results show that the engine can be ignited but the combustion cannot be sustained when head spark plug applied as the plug tip was set in the gaseous low-velocity zone with thin spray.This is mainly because flame from this zone cannot supply enough ignition energy for the whole chamber.However,reliable ignition and stable combustion can be achieved by body spark plug.As the O/F ratio increases from 2.61 to 3.49,chamber pressure increases from 0.474 to 0.925 MPa and combustion efficiency increases from 57.8%to 95.1%.This is determined by the injector configuration,which cannot produce the sufficiently breakup of the liquid oxygen on the low flow rate case.
基金Projects funded by the National Social Science Fund (19BDJ064)
文摘This paper provides a detailed introduction to and analysis of the course of China's technological innovation in liquid hydrogen/liquid oxygen(LH2/LOX)rocket engines from a historical point of view.It starts with the investigation of LH2/LOX rocket engines by relevant departments of the Chinese Academy of Sciences in the 1960s and their preliminary achievements.Then,the policy decision concerning LH2/LOX engine development,the project approval of the Long March-3(Chang Zheng-3,CZ-3)rocket,and the process of developing LH2/LOX engines are analyzed in detail,followed by an introduction to and summary of the development situation and technical innovation characteristics of China's LH2/LOX engines as they grew from 4 tons to 8 tons,and finally to 50 tons.Finally,the paper briefly analyzes the innovation experience connected with China's LH2/LOX engines.
文摘Numerical 2D simulation and research on internal flow field and external flow field of rocket motor nozzle using FLUENT software. Analyze the flow condition of internal flow field and external flow field, and according to add in the amount of the different gas components, obtain the clear distribution of contour of density flow field, pressure flow field and various material components and so on. Simulation results agree with the results observed from the test on the ground, and provide reference for solid rocket motor development.
文摘Liquid propellant rocket engines for a launch vehicle are an essential aerospace technology, representing the advanced level of hi-tech in a country. In recent years, China’s aerospace industry has made remarkable achievements, and liquid rocket engine technology has also been effectively developed. In this article, the development processes of China’s liquid rocket engines are discussed. Then, the performance features of China’s new generation liquid rocket engines as well as the flight tests of the new-generation launch vehicles are introduced. Finally, the development direction and the most recent progress of the next generation large-thrust liquid rocket engine is presented.
文摘Based on current research,the development trend of reusable liquid rocket engines was analyzed.Key technologies and research focuses of the reusable liquid rocket engine have been analyzed and summarized,and then suggestions on the development of future key technologies are proposed.
文摘Safety analysis for liquid rocket engine has a great meaning for shortening development cycle, saving development expenditure and reducing development risk. The relationship between the structure and component of liquid rocket engine is much more complex, furthermore test data are absent in development phase. Thereby, the uncertainties exist in safety analysis for liquid rocket engine. A safety analysis model integrated with FMEA(failure mode and effect analysis) based on Bayesian networks (BN) is brought forward for liquid rocket engine, which can combine qualitative analysis with quantitative decision. The method has the advantages of fusing multi-information, saving sample amount and having high veracity. An example shows that the method is efficient.
文摘The ablative material is supposed to be one of good candidates for LRE （liquid rocket engine） combustion chamber to achieve both high reliability and low cost and a numerical analysis for the ablator is considered to be a potentially efficient tool to reduce cost as well. So far, ablators have been successfully applied for many SRM （solid rocket motors）, but the application to LRE is still quite limited in Japan. The authors believe that this is primarily because of the unpredictable nature of the heat load from combustion gases to the combustor wall. Indeed, reliable thermal design of ablative combustion chamber, namely reliable prediction of thermal performance, needs both reliable heat load model and reliable ablator response model. This paper elaborates our research activities and our recent research findings.
文摘An electro-hydraulic actuator for the thrust vector control(TVC)of a throttlable kerolox rocket engine is introduced in this paper.The creative feature is an integrated hydraulic power drive unit,where a constant speed kerosene motor is used to draw high pressure kerosene from the engine and to drive a constant pressure variable displacement piston pump,acting as the power supply for the actuator.Its operational mechanism,to accommodate the varying pressure from the turbo-pump of a throttling engine,lies in a pressure-reducing flow regulator inserted at the motor inlet.Another key point is that the displacement of the motor is reasonably bigger than the pump so that a sufficiently wide range of pressures can be adapted.Modeling analysis and flight test results were well matched,which show the outstanding performance of this novel type actuator.
