Two kinds of W/Cu double-layer shaped charge liner（SCL） were prepared by chemical vapor deposition（CVD） combined with electroforming technique： A SCL with W inner layer and Cu outer layer, B SCL with Cu inner lay...Two kinds of W/Cu double-layer shaped charge liner（SCL） were prepared by chemical vapor deposition（CVD） combined with electroforming technique： A SCL with W inner layer and Cu outer layer, B SCL with Cu inner layer and W outer layer. The penetration properties of A and B SCLs were researched. The results show that the two SCLs can form continuous jet and the tip velocities of A and B jets are 7.4 and 6.3 km s^（-1）, respectively. The kinetic energy density（5.3 9 1011 J m-3） of A jet tip increases by 194.4 %compared with that（1.8 9 1011 J m-3） of B jet tip. B jet,however, exhibits deeper penetration depth at the same experimental conditions. The chemical component and microstructure of the area nearby the ballistic perforation were researched. Component analysis shows that both the jets are formed only from inner layer metal. Microstructure analysis shows that martensite and intermetallic form around ballistic perforation penetrated by A SCL due to the intensive interaction between W jet and steel target. The two kinds of newly formed ultrahard phases also hinder the jet from penetrating target further. As a result of relatively alleviative interaction between Cu jet and target, only solid solution rather than ultrahard phases forms around ballistic perforation penetrated by B SCL.展开更多
This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double...This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double-layer charge liners were fabricated by using CVD to deposit tungsten layers on the inner surfaces of pure T2 copper liners.The microstructures of the tungsten layers were analyzed using a scanning electron microscope(SEM).The feasibility analysis was carried out by pulsed X-rays,slug-retrieval test and static penetration tests.The shaped charge jet forming and penetration law of inner tungsten-coated double-layer liner were studied by numerical simulation method.The results showed that the double-layer liners could form well-shaped jets.The errors between the X-ray test results and the numerical results were within 11.07%.A slug-retrieval test was found that the retrieved slug was similar to a numerically simulated slug.Compared with the traditional pure copper shaped charge jet,the penetration depth of the double-layer shaped charge liner increased by 11.4% and>10.8% respectively.In summary,the test results are good,and the numerical simulation is in good agreement with the test,which verified the feasibility of using the CVD method to fabricate double-layer charge liners with a high-density and high-strength refractory metal as the inner liner.展开更多
Two-dimensional double-layer honeycomb(DLHC)materials are known for their diverse physical properties,but superconductivity has been a notably absent characteristic in this structure.We address this gap by investigati...Two-dimensional double-layer honeycomb(DLHC)materials are known for their diverse physical properties,but superconductivity has been a notably absent characteristic in this structure.We address this gap by investigating M_(2)N_(2)(M=Nb,Ta)with DLHC structure using first-principles calculations.Our results show that M_(2)N_(2)are stable and metallic,exhibiting superconducting behavior.Specifically,Nb_(2)N_(2)and Ta_(2)N_(2)display superconducting transition temperatures of 6.8 K and 8.8 K,respectively.Their electron-phonon coupling is predominantly driven by the coupling between metal d-orbitals and low-frequency metal-dominated vibration modes.Interestingly,two compounds also exhibit non-trivial band topology.Thus,M_(2)N_(2)are promising platforms for studying the interplay between topology and superconductivity and fill the gap in superconductivity research for DLHC materials.展开更多
The service life of internal combustion engines is significantly influenced by surface defects in cylinder liners.To address the limitations of traditional detection methods,we propose an enhanced YOLOv8 model with Sw...The service life of internal combustion engines is significantly influenced by surface defects in cylinder liners.To address the limitations of traditional detection methods,we propose an enhanced YOLOv8 model with Swin Transformer as the backbone network.This approach leverages Swin Transformer's multi-head self-attention mechanism for improved feature extraction of defects spanning various scales.Integrated with the YOLOv8 detection head,our model achieves a mean average precision of 85.1%on our dataset,outperforming baseline methods by 1.4%.The model's effectiveness is further demonstrated on a steel-surface defect dataset,indicating its broad applicability in industrial surface defect detection.Our work highlights the potential of combining Swin Transformer and YOLOv8 for accurate and efficient defect detection.展开更多
BACKGROUND Total hip arthroplasty is a safe and effective procedure.To improve survivorship,ultrahigh molecular weight polyethylene hip liners with antioxidants have been developed.Additive antioxidant was deployed to...BACKGROUND Total hip arthroplasty is a safe and effective procedure.To improve survivorship,ultrahigh molecular weight polyethylene hip liners with antioxidants have been developed.Additive antioxidant was deployed to reduce oxidation and consequential wear,loosening,or osteolysis.A unique manufacturing process was utilized for two such hip liners,the Novation®and Alteon®XLE hip liners and this research represents the first large series on this specific material.The study hypothesis was that Novation and Alteon XLE hip liners have similar short-term survivorship as other manufacturers’antioxidant liners according to procedure and outcome data from the American Joint Replacement Registry(AJRR).AIM To demonstrate similar short-term survivorship of XLE antioxidant hip liners compared to all antioxidant hip liners in AJRR.METHODS Utilizing total hip arthroplasty data from the AJRR,a retrospective review was performed for subjects who underwent implantation of Novation XLE(n=461),Alteon XLE(n=989),or any other antioxidant hip liner(termed the aggregate antioxidant group;n=39964)as of March 31,2022.Survivorship at three years and revision rates were compared statistically between the Novation group and the aggregate antioxidant group as well as the Alteon group and the aggregate antioxidant group.RESULTS Survivorship at three years post-surgery was 99.09%for Novation,97.73%for Alteon,and 97.69%for the aggregate antioxidant group.There were no reports of failure due to wear in either the Novation or Alteon groups.Among the revision categories(fracture,infection,aseptic loosening,instability,mechanical complications,wear,pain,hematoma/wound complications,or other),there were no significant differences identified in either comparison.There were also no significant differences in cumulative percent revision rates up to three years post-surgery for the Novation vs aggregate antioxidant group or the Alteon vs aggregate antioxidant group.CONCLUSION Novation and Alteon XLE hip liner revision rate and survivorship are equivalent to other antioxidant hip liners in the short term.展开更多
BACKGROUND Medial dished(MD)liner designs for cruciate-retaining(CR)total knee arthroplasty(TKA)are a relatively novel development.MD tibial inserts have a more constraining medial side,which allows for more similar k...BACKGROUND Medial dished(MD)liner designs for cruciate-retaining(CR)total knee arthroplasty(TKA)are a relatively novel development.MD tibial inserts have a more constraining medial side,which allows for more similar kinematics and function to a native knee.AIM To evaluate the clinical results and patient-reported outcomes after CR TKA procedures utilizing a kinematically designed medial dish system.METHODS A multicenter,retrospective cohort review of 139 primary elective TKAs utilizing a kinematically designed CR Knee System(JOURNEY™II CR MD;Smith and Nephew,Memphis,TN,United States)at three different institutions with a minimum of two years of follow-up.Demographic information,clinical outcomes,and patient-reported outcome measures were collected and analyzed.RESULTS With up to 3.7 years from surgery,overall implant survivorship was 98.6%.There were significant postoperative increases in the average Knee Injury and Osteoarthritis Outcome Score for Joint Replacement scores(17.4 at 6 months,26.1 points at two years or more,P<0.001).CONCLUSION The combination of high implant survivorship and substantial improvements in patient-reported outcome measures suggests that the medial dish tibial insert represents a safe and effective option within TKA.Additional investigation is necessary to evaluate the long-term survivorship of this design.展开更多
In order to establish the relationship between the measured dynamic response and the health status of long-span bridges, a double-layer model updating method for steel-concrete composite beam cable-stayed bridges is p...In order to establish the relationship between the measured dynamic response and the health status of long-span bridges, a double-layer model updating method for steel-concrete composite beam cable-stayed bridges is proposed. Measured frequencies are selected as the first-layer reference data, and the mass of the bridge deck, the grid density, the modulus of concrete and the ballast on the side span are modified by using a manual tuning technique. Measured global positioning system （GPS） data is selected as the second-layer reference data, and the degradation of the integral structure stiffness EI of the whole bridge is taken into account for the second-layer model updating by using the finite element iteration algorithm. The Nanpu Bridge in Shanghai is taken as a case to verify the applicability of the proposed model updating method. After the first-layer model updating, the standard deviation of modal frequencies is smaller than 7%. After the second-layer model updating, the error of the deflection of the mid-span is smaller than 10%. The integral structure stiffness of the whole bridge decreases about 20%. The research results show a good agreement between the calculated response and the measured response.展开更多
In order to increase the fatigue life (FL) of road wheels (RW), a kind of double layer rubber flange (DLRF) is put forward. It consists of two layers of rubber, where metal wires are laid in the inner layer and the ou...In order to increase the fatigue life (FL) of road wheels (RW), a kind of double layer rubber flange (DLRF) is put forward. It consists of two layers of rubber, where metal wires are laid in the inner layer and the outer layer has no inlaid metal wires. Stress, strain and temperature field of DLRF were calculated with ANSYS finite element analysis (FEA) software, FL of DLRF RW was also computed with fracture mechanics fatigue theory. The results of computation indicate that the heat generated in RW's rubber flange (RF) can be reduced by the use of DLRF, and the FL of RW can be increased without affecting the mechanical intensity of RW.展开更多
The aim of the study was to develop actarit double-layered osmotic pump tablets to overcome the weak points of actarit common tablets, such as short half-life and large plasma concentration fluctuations. Single factor...The aim of the study was to develop actarit double-layered osmotic pump tablets to overcome the weak points of actarit common tablets, such as short half-life and large plasma concentration fluctuations. Single factor experiment and orthogonal test were applied to optimize the formulation;the pharmacokinetic study was performed in beagle dogs adopting actarit common tablets as reference tablets. The optimal formulation was as follows: drug layer: 150 mg actarit, 240 mg PEO-N80, 50 mg NaCl;push layer: 140 mg PEO-WSR303, 20 mg NaCl;coating solution: 30 g cellulose acetate and 6 g PEG 4000 in 1000 ml 94% acetone solution, 60 mg coating weight gain. The pharmacokinetic study showed that T max was prolonged by the contrast of commercial common tablets with constant drug release rate, but the bioavailability was equivalent. And a good in vivo –in vitro correlation of the actarit osmotic pump tablets was also established. The designed actarit osmotic pump tablets can be applied for rheumatoid arthritis, proposing a promising replacement for the marked common products.展开更多
In order to address the current aircraft noise problem, the knowledge of impedance of acoustic liners subjected to high-intensity sound and grazing flow is of crucial importance to the design of high-efficiency acoust...In order to address the current aircraft noise problem, the knowledge of impedance of acoustic liners subjected to high-intensity sound and grazing flow is of crucial importance to the design of high-efficiency acoustic nacelles. To this end, the present study is twofold. Firstly, the StraightForward impedance eduction Method(SFM) is evaluated by the strategy that the impedance of a liner specimen is firstly experimentally educed on a flow duct using the SFM, and then its accuracy is checked by comparing the numerical prediction with the measured wall sound pressure of the flow duct. Secondly, the effects of grazing flow and high-intensity sound on the impedance behavior of two single-layer liners are investigated based on comparisons between educed impedance and predictions by three impedance models. The performance of the SFM is validated by showing that the educed impedance leads to excellent agreement between the simulation and the measured wall sound pressure for different grazing flow Mach numbers and Sound Pressure Levels(SPLs) and over a frequency range from 3000 Hz down to 500 Hz. The grazing flow effect generally has the tendency that the acoustic resistance exhibits a slight decrease before it increases linearly with an increase in Mach,predicted successfully by the sound-vortex interaction theoretical model and the Kooi semi-empirical impedance model. However, the Goodrich semi-empirical impedance model gives only a simple linear relation of acoustic resistance starting from Mach zero. Additionally, when the SPL increases from 110 to 140 d B in the present investigation, the acoustic resistance exhibits a significant increase at all frequencies in the absence of flow; however, the resistance decreases slightly under a grazing flow of Mach 0.117. It indicates that the SPL effect can be greatly inhibited when flow is present,and the grazing flow effect can be reduced partly as well at a relatively high SPL.展开更多
AIM To investigate the efficacy of double-layered covered stent in the treatment of malignant oesophageal obstructions.METHODS A systematic review and meta-analysis was performed following the PRISMA process. Pub Med(...AIM To investigate the efficacy of double-layered covered stent in the treatment of malignant oesophageal obstructions.METHODS A systematic review and meta-analysis was performed following the PRISMA process. Pub Med(Medline),EMBASE(Excerpta Medical Database),AMED(Allied and Complementary medicine Database),Scopus and online content,were searched for studies reporting on the Ni Ti-S polyurethane-covered double oesophageal stent for the treatment of malignant dysphagia. Weighted pooled outcomes were synthesized with a random effects model to account for clinical heterogeneity. All studies reporting the outcome of palliative management of dysphagia due to histologically confirmed malignant oesophageal obstruction using double-layered covered nitinol stent were included. The level of statistical significance was set at α = 0.05.RESULTS Six clinical studies comprising 250 patients in total were identified. Pooled technical success of stent insertion was 97.2%(95%CI: 94.8%-98.9%; I2 = 5.8%). Pooled complication rate was 27.6%(95%CI: 20.7%-35.2%; I2 = 41.9%). Weighted improvement of dysphagia on a scale of 0-5 scoring system was-2.00 [95%CI:-2.29%-(-1.72%); I2 = 87%]. Distal stent migration was documented in 10 out of the 250 cases examined.Pooled stent migration rate was 4.7%(95%CI: 2.5%-7.7%; I2 = 0%). Finally,tumour overgrowth was reported in 34 out of the 250 cases with pooled rate of tumour overgrowth of 11.2%(95%CI: 3.7%-22.1%; I2 = 82.2%). No funnel plot asymmetry to suggest publication bias(bias = 0.39,P = 0.78). In the sensitivity analysis all results were largely similar between the fixed and random effects models.CONCLUSION The double-layered nitinol stent provides immediate relief of malignant dysphagia with low rates of stent migration and tumour展开更多
Based on non-Darcian flow law described by exponent and threshold gradient within a double-layered soil, the classic theory of one-dimensional consolidation of double-layered soil was modified to consider the change o...Based on non-Darcian flow law described by exponent and threshold gradient within a double-layered soil, the classic theory of one-dimensional consolidation of double-layered soil was modified to consider the change of vertical total stress with depth and time together. Because of the complexity of governing equations, the numerical solutions were obtained in detail by finite difference method. Then, the numerical solutions were compared with the analytical solutions in condition that non-Darcian flow law was degenerated to Dary's law, and the comparison results show that numerical solutions are reliable. Finally, consolidation behavior of double-layered soil with different parameters was analyzed, and the results show that the consolidation rate of double-layered soil decreases with increasing the value of exponent and threshold of non-Darcian flow, and the exponent and threshold gradient of the first soil layer greatly influence the consolidation rate of double-layered soil. The larger the ratio of the equivalent water head of external load to the total thickness of double-layered soil, the larger the rate of the consolidation, and the similitude relationship in classical consolidation theory of double-layered soil is not satisfied. The other consolidation behavior of double-layered soil with non-Darcian flow is the same as that with Darcy's law.展开更多
To further investigate the one-dimensional(1D)rheological consolidation mechanism of double-layered soil,the fractional derivative Merchant model(FDMM)and the non-Darcian flow model with the non-Newtonian index are re...To further investigate the one-dimensional(1D)rheological consolidation mechanism of double-layered soil,the fractional derivative Merchant model(FDMM)and the non-Darcian flow model with the non-Newtonian index are respectively introduced to describe the deformation of viscoelastic soil and the flow of pore water in the process of consolidation.Accordingly,an 1D rheological consolidation equation of double-layered soil is obtained,and its numerical analysis is performed by the implicit finite difference method.In order to verify its validity,the numerical solutions by the present method for some simplified cases are compared with the results in the related literature.Then,the influence of the revelent parameters on the rheological consolidation of double-layered soil are investigated.Numerical results indicate that the parameters of non-Darcian flow and FDMM of the first soil layer greatly influence the consolidation rate of double-layered soil.As the decrease of relative compressibility or the increase of relative permeability between the lower soil and the upper soil,the dissipation rate of excess pore water pressure and the settlement rate of the ground will be accelerated.Increasing the relative thickness of soil layer with high permeability or low compressibility will also accelerate the consolidation rate of double-layered soil.展开更多
As an important scheme of future global mobile satellite communication systems to provide multimedia service, a Double-Layer Satellite Network （DLSN） with MEO satellites and LEO satellites is proposed. The Inter-Orb...As an important scheme of future global mobile satellite communication systems to provide multimedia service, a Double-Layer Satellite Network （DLSN） with MEO satellites and LEO satellites is proposed. The Inter-Orbit-Links （IOLs） between layers is an essential factor, which affects the performances of the DLSN systems. Considering certain constellation parameters, the geometric characteristics of IOLs are described and the connectivity of MEO satellites and LEO satellites in the DLSN is analyzed. By computer simulation, the results show that IOLs should be selectively established according to certain parameters rather than the simple in-sight principle.展开更多
The velocity structures of flow through vertically double-layered vegetation(VDLV)as well as single-layered rigid vegetation(SLV)were investigated computationally with a three-dimensional(3D)Reynolds stress turbulence...The velocity structures of flow through vertically double-layered vegetation(VDLV)as well as single-layered rigid vegetation(SLV)were investigated computationally with a three-dimensional(3D)Reynolds stress turbulence model,using the computational fluid dynamics(CFD)code FLUENT.The detailed velocity distribution was explored with a varying initial Froude number(Fr),with consideration of the steady subcritical flow conditions of an inland tsunami.In VDLV flows,the numerical model successfully captured the inflection point in the profiles of mean streamwise velocities in the mixing-layer region around the top of short submerged vegetation.An upward and downward movement of flow occurred at the positions located just behind the tall and short vegetation,respectively.Overall,higher streamwise velocities were observed in the upper vegetation layer due to high porosity,with Pr=98%(sparse vegetation,where Pr is the porosity),as compared to those in the lower vegetation layer,which had comparatively low porosity,with Pr=91%(dense vegetation).A rising trend of velocities was found as the flow passed through the vegetation region,followed by a clear sawtooth distribution,as compared to the regions just upstream and downstream of vegetation where the flow was almost uniform.In VDLV flows,a rising trend in the flow resistance was observed with the increase in the initial Froude number,i.e.,Fr?0.67,0.70,and 0.73.However,the flow resistance in the case of SLV was relatively very low.The numerical results also show the flow structures within the vicinity of short and tall vegetation,which are difficult to attain through experimental measurements.展开更多
The time-sequenced damage behavior of the reactive projectile impacting double-layer plates is discussed.The analytical model considering the combined effect of kinetic and chemical energy is developed to reveal the d...The time-sequenced damage behavior of the reactive projectile impacting double-layer plates is discussed.The analytical model considering the combined effect of kinetic and chemical energy is developed to reveal the damage mechanism.The influences of impact velocity and reactive projectile chemical characteristics on the damage effect are decoupled analyzed based on this model.These analyses indicate that the high energy releasing efficiency and fast reaction propagation velocity of the reactive projectile are conducive to enhancing the damage effect.The experiments with various reactive projectiles impact velocity increasing from 702 to 1385 m/s were conducted to verify this model.The experimental results presented that,the damage hole radius of the rear-plate increases with the increase of impact velocity.At the impact velocity of 1350 m/s,the radius of damage hole formed by PTFE/Al/Bi_(2)O_(3),PTFE/Al/MoO_(3),PTFE/Al/Fe_(2)O_(3)projectile on the rear-plate become smaller in sequence.These results are consistent with the analytical model prediction,demonstrating that this model can predict the damage effect quantitatively.This work is of constructive significance to the application of reactive projectiles.展开更多
A simple, precise and accurate method was developed and validated for the determination of allicin release from alliin/alliinase double-layer tablets. According to Appendix XC Ⅱ of Chinese Pharmacopoeia 2010 edition ...A simple, precise and accurate method was developed and validated for the determination of allicin release from alliin/alliinase double-layer tablets. According to Appendix XC Ⅱ of Chinese Pharmacopoeia 2010 edition Volume II, a small glass-method was adopted at the rotational speed of 100 r/min using 100 mL phosphate buffer （pH 6.8） as release medium. The release amount was determined by HPLC with a C18 column （250 mm × 4.6 mm, 5 μm） using the mobile phase consisting of methanol -0.4% carboxylic acid （65：35） at a flow rate of 1 mL/min and UV detection at 242 nm. The current method demonstrates good linearity over the range 4.052- 405.2 μg/mL （r2=0.9999） with an average recovery of 105.5%（RSD= 1.25%）. The accumulative release of alliin/alliinase double-layer tablets had good homogeneity for withinand betweenbatches. The method established is simple, accurate and repeatable for the determination of allicin release from alliin/alliinase double-layer tablets.展开更多
The adsorption capacity of landfill liners containing granular activated carbon (GAC), or bentonite activated by acid, for Cr(VI) was investigated by batch testing. The results show that both GAC and activated bentoni...The adsorption capacity of landfill liners containing granular activated carbon (GAC), or bentonite activated by acid, for Cr(VI) was investigated by batch testing. The results show that both GAC and activated bentonite could be used as sorptive amendments for trapping Cr(VI) in landfill liners. The Cr(VI) sorption to GAC and activated bentonite is much greater than Cr(VI) sorption to natural clay. The adsorption capacity of Cr(VI) onto all the soils increases with increasing temperature; adsorption capacity is also significantly influenced by soil-solid concentration. As the soil-solid concentration increases the adsorption capacity first decreases logarithmically, but then stabilizes when the soil-solid concentration exceeds a critical value (e.g. 400 g/L). Permeability tests were conducted in the laboratory. The results indicate that the hydraulic conductivity of landfill liners containing GAC or activated bentonite can meet the engineering requirement of 1 nm/s. One-dimensional transport simulations for Cr(VI) were performed to evaluate the effect of GAC and activated bentonite on landfill liners. The results of the simulations indicate that landfill liners containing GAC, or activated bentonite, significantly retard the transport of Cr(VI) relative to a conventional clay liner.展开更多
To understand the mesoscopic mechanism of clayey soil in view of macroscopic behavior, it is essential to quantitatively calculate the electric double-layer repulsion between arbitrarily inclined clay particles.Howeve...To understand the mesoscopic mechanism of clayey soil in view of macroscopic behavior, it is essential to quantitatively calculate the electric double-layer repulsion between arbitrarily inclined clay particles.However, suitable calculation methods with high efficiency and accuracy are still rare at present in literature. Based on a great number of numerical calculations of the repulsion between two inclined platy clay particles, explicit empirical formulae for estimating electric double-layer repulsion between clay particles are put forward. Comparison between the empirical solutions and corresponding numerical results shows that the proposed formulae have a reasonable accuracy, and application of the presented formula is easy and efficient.展开更多
基金financially supported by the National Natural Science Foundation of China(No.51201013)
文摘Two kinds of W/Cu double-layer shaped charge liner（SCL） were prepared by chemical vapor deposition（CVD） combined with electroforming technique： A SCL with W inner layer and Cu outer layer, B SCL with Cu inner layer and W outer layer. The penetration properties of A and B SCLs were researched. The results show that the two SCLs can form continuous jet and the tip velocities of A and B jets are 7.4 and 6.3 km s^（-1）, respectively. The kinetic energy density（5.3 9 1011 J m-3） of A jet tip increases by 194.4 %compared with that（1.8 9 1011 J m-3） of B jet tip. B jet,however, exhibits deeper penetration depth at the same experimental conditions. The chemical component and microstructure of the area nearby the ballistic perforation were researched. Component analysis shows that both the jets are formed only from inner layer metal. Microstructure analysis shows that martensite and intermetallic form around ballistic perforation penetrated by A SCL due to the intensive interaction between W jet and steel target. The two kinds of newly formed ultrahard phases also hinder the jet from penetrating target further. As a result of relatively alleviative interaction between Cu jet and target, only solid solution rather than ultrahard phases forms around ballistic perforation penetrated by B SCL.
基金funded by the China Postdoctoral Science Foundation(Grant No.2022M721614)the opening project of State Key Laboratory of Explosion Science and Technology,Beijing Institute of Technology(Grant No.KFJJ23-07M)。
文摘This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double-layer charge liners were fabricated by using CVD to deposit tungsten layers on the inner surfaces of pure T2 copper liners.The microstructures of the tungsten layers were analyzed using a scanning electron microscope(SEM).The feasibility analysis was carried out by pulsed X-rays,slug-retrieval test and static penetration tests.The shaped charge jet forming and penetration law of inner tungsten-coated double-layer liner were studied by numerical simulation method.The results showed that the double-layer liners could form well-shaped jets.The errors between the X-ray test results and the numerical results were within 11.07%.A slug-retrieval test was found that the retrieved slug was similar to a numerically simulated slug.Compared with the traditional pure copper shaped charge jet,the penetration depth of the double-layer shaped charge liner increased by 11.4% and>10.8% respectively.In summary,the test results are good,and the numerical simulation is in good agreement with the test,which verified the feasibility of using the CVD method to fabricate double-layer charge liners with a high-density and high-strength refractory metal as the inner liner.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.12074213 and 11574108)the National Key R&D Program of China(Grant No.2022YFA1403103)+2 种基金the Major Basic Program of Natural Science Foundation of Shandong Province(Grant No.ZR2021ZD01)the Natural Science Foundation of Shandong Province(Grant No.ZR2023MA082)the Project of Introduction and Cultivation for Young Innovative Talents in Colleges and Universities of Shandong Province。
文摘Two-dimensional double-layer honeycomb(DLHC)materials are known for their diverse physical properties,but superconductivity has been a notably absent characteristic in this structure.We address this gap by investigating M_(2)N_(2)(M=Nb,Ta)with DLHC structure using first-principles calculations.Our results show that M_(2)N_(2)are stable and metallic,exhibiting superconducting behavior.Specifically,Nb_(2)N_(2)and Ta_(2)N_(2)display superconducting transition temperatures of 6.8 K and 8.8 K,respectively.Their electron-phonon coupling is predominantly driven by the coupling between metal d-orbitals and low-frequency metal-dominated vibration modes.Interestingly,two compounds also exhibit non-trivial band topology.Thus,M_(2)N_(2)are promising platforms for studying the interplay between topology and superconductivity and fill the gap in superconductivity research for DLHC materials.
基金supported by the Scientific and technological key project in Henan Province 22210224002the Natural Science Foundation of Henan Polytechnic University B2021-38.
文摘The service life of internal combustion engines is significantly influenced by surface defects in cylinder liners.To address the limitations of traditional detection methods,we propose an enhanced YOLOv8 model with Swin Transformer as the backbone network.This approach leverages Swin Transformer's multi-head self-attention mechanism for improved feature extraction of defects spanning various scales.Integrated with the YOLOv8 detection head,our model achieves a mean average precision of 85.1%on our dataset,outperforming baseline methods by 1.4%.The model's effectiveness is further demonstrated on a steel-surface defect dataset,indicating its broad applicability in industrial surface defect detection.Our work highlights the potential of combining Swin Transformer and YOLOv8 for accurate and efficient defect detection.
文摘BACKGROUND Total hip arthroplasty is a safe and effective procedure.To improve survivorship,ultrahigh molecular weight polyethylene hip liners with antioxidants have been developed.Additive antioxidant was deployed to reduce oxidation and consequential wear,loosening,or osteolysis.A unique manufacturing process was utilized for two such hip liners,the Novation®and Alteon®XLE hip liners and this research represents the first large series on this specific material.The study hypothesis was that Novation and Alteon XLE hip liners have similar short-term survivorship as other manufacturers’antioxidant liners according to procedure and outcome data from the American Joint Replacement Registry(AJRR).AIM To demonstrate similar short-term survivorship of XLE antioxidant hip liners compared to all antioxidant hip liners in AJRR.METHODS Utilizing total hip arthroplasty data from the AJRR,a retrospective review was performed for subjects who underwent implantation of Novation XLE(n=461),Alteon XLE(n=989),or any other antioxidant hip liner(termed the aggregate antioxidant group;n=39964)as of March 31,2022.Survivorship at three years and revision rates were compared statistically between the Novation group and the aggregate antioxidant group as well as the Alteon group and the aggregate antioxidant group.RESULTS Survivorship at three years post-surgery was 99.09%for Novation,97.73%for Alteon,and 97.69%for the aggregate antioxidant group.There were no reports of failure due to wear in either the Novation or Alteon groups.Among the revision categories(fracture,infection,aseptic loosening,instability,mechanical complications,wear,pain,hematoma/wound complications,or other),there were no significant differences identified in either comparison.There were also no significant differences in cumulative percent revision rates up to three years post-surgery for the Novation vs aggregate antioxidant group or the Alteon vs aggregate antioxidant group.CONCLUSION Novation and Alteon XLE hip liner revision rate and survivorship are equivalent to other antioxidant hip liners in the short term.
文摘BACKGROUND Medial dished(MD)liner designs for cruciate-retaining(CR)total knee arthroplasty(TKA)are a relatively novel development.MD tibial inserts have a more constraining medial side,which allows for more similar kinematics and function to a native knee.AIM To evaluate the clinical results and patient-reported outcomes after CR TKA procedures utilizing a kinematically designed medial dish system.METHODS A multicenter,retrospective cohort review of 139 primary elective TKAs utilizing a kinematically designed CR Knee System(JOURNEY™II CR MD;Smith and Nephew,Memphis,TN,United States)at three different institutions with a minimum of two years of follow-up.Demographic information,clinical outcomes,and patient-reported outcome measures were collected and analyzed.RESULTS With up to 3.7 years from surgery,overall implant survivorship was 98.6%.There were significant postoperative increases in the average Knee Injury and Osteoarthritis Outcome Score for Joint Replacement scores(17.4 at 6 months,26.1 points at two years or more,P<0.001).CONCLUSION The combination of high implant survivorship and substantial improvements in patient-reported outcome measures suggests that the medial dish tibial insert represents a safe and effective option within TKA.Additional investigation is necessary to evaluate the long-term survivorship of this design.
基金The Special Project of the Ministry of Construction ofChina (No.20060909).
文摘In order to establish the relationship between the measured dynamic response and the health status of long-span bridges, a double-layer model updating method for steel-concrete composite beam cable-stayed bridges is proposed. Measured frequencies are selected as the first-layer reference data, and the mass of the bridge deck, the grid density, the modulus of concrete and the ballast on the side span are modified by using a manual tuning technique. Measured global positioning system （GPS） data is selected as the second-layer reference data, and the degradation of the integral structure stiffness EI of the whole bridge is taken into account for the second-layer model updating by using the finite element iteration algorithm. The Nanpu Bridge in Shanghai is taken as a case to verify the applicability of the proposed model updating method. After the first-layer model updating, the standard deviation of modal frequencies is smaller than 7%. After the second-layer model updating, the error of the deflection of the mid-span is smaller than 10%. The integral structure stiffness of the whole bridge decreases about 20%. The research results show a good agreement between the calculated response and the measured response.
文摘In order to increase the fatigue life (FL) of road wheels (RW), a kind of double layer rubber flange (DLRF) is put forward. It consists of two layers of rubber, where metal wires are laid in the inner layer and the outer layer has no inlaid metal wires. Stress, strain and temperature field of DLRF were calculated with ANSYS finite element analysis (FEA) software, FL of DLRF RW was also computed with fracture mechanics fatigue theory. The results of computation indicate that the heat generated in RW's rubber flange (RF) can be reduced by the use of DLRF, and the FL of RW can be increased without affecting the mechanical intensity of RW.
文摘The aim of the study was to develop actarit double-layered osmotic pump tablets to overcome the weak points of actarit common tablets, such as short half-life and large plasma concentration fluctuations. Single factor experiment and orthogonal test were applied to optimize the formulation;the pharmacokinetic study was performed in beagle dogs adopting actarit common tablets as reference tablets. The optimal formulation was as follows: drug layer: 150 mg actarit, 240 mg PEO-N80, 50 mg NaCl;push layer: 140 mg PEO-WSR303, 20 mg NaCl;coating solution: 30 g cellulose acetate and 6 g PEG 4000 in 1000 ml 94% acetone solution, 60 mg coating weight gain. The pharmacokinetic study showed that T max was prolonged by the contrast of commercial common tablets with constant drug release rate, but the bioavailability was equivalent. And a good in vivo –in vitro correlation of the actarit osmotic pump tablets was also established. The designed actarit osmotic pump tablets can be applied for rheumatoid arthritis, proposing a promising replacement for the marked common products.
基金co-supported by the National Natural Science Foundation of China (No. 51576009)the Projects of International Cooperation and Exchanges National Natural Science Foundation of China (Nos.11661141020 and 51711530036)
文摘In order to address the current aircraft noise problem, the knowledge of impedance of acoustic liners subjected to high-intensity sound and grazing flow is of crucial importance to the design of high-efficiency acoustic nacelles. To this end, the present study is twofold. Firstly, the StraightForward impedance eduction Method(SFM) is evaluated by the strategy that the impedance of a liner specimen is firstly experimentally educed on a flow duct using the SFM, and then its accuracy is checked by comparing the numerical prediction with the measured wall sound pressure of the flow duct. Secondly, the effects of grazing flow and high-intensity sound on the impedance behavior of two single-layer liners are investigated based on comparisons between educed impedance and predictions by three impedance models. The performance of the SFM is validated by showing that the educed impedance leads to excellent agreement between the simulation and the measured wall sound pressure for different grazing flow Mach numbers and Sound Pressure Levels(SPLs) and over a frequency range from 3000 Hz down to 500 Hz. The grazing flow effect generally has the tendency that the acoustic resistance exhibits a slight decrease before it increases linearly with an increase in Mach,predicted successfully by the sound-vortex interaction theoretical model and the Kooi semi-empirical impedance model. However, the Goodrich semi-empirical impedance model gives only a simple linear relation of acoustic resistance starting from Mach zero. Additionally, when the SPL increases from 110 to 140 d B in the present investigation, the acoustic resistance exhibits a significant increase at all frequencies in the absence of flow; however, the resistance decreases slightly under a grazing flow of Mach 0.117. It indicates that the SPL effect can be greatly inhibited when flow is present,and the grazing flow effect can be reduced partly as well at a relatively high SPL.
文摘AIM To investigate the efficacy of double-layered covered stent in the treatment of malignant oesophageal obstructions.METHODS A systematic review and meta-analysis was performed following the PRISMA process. Pub Med(Medline),EMBASE(Excerpta Medical Database),AMED(Allied and Complementary medicine Database),Scopus and online content,were searched for studies reporting on the Ni Ti-S polyurethane-covered double oesophageal stent for the treatment of malignant dysphagia. Weighted pooled outcomes were synthesized with a random effects model to account for clinical heterogeneity. All studies reporting the outcome of palliative management of dysphagia due to histologically confirmed malignant oesophageal obstruction using double-layered covered nitinol stent were included. The level of statistical significance was set at α = 0.05.RESULTS Six clinical studies comprising 250 patients in total were identified. Pooled technical success of stent insertion was 97.2%(95%CI: 94.8%-98.9%; I2 = 5.8%). Pooled complication rate was 27.6%(95%CI: 20.7%-35.2%; I2 = 41.9%). Weighted improvement of dysphagia on a scale of 0-5 scoring system was-2.00 [95%CI:-2.29%-(-1.72%); I2 = 87%]. Distal stent migration was documented in 10 out of the 250 cases examined.Pooled stent migration rate was 4.7%(95%CI: 2.5%-7.7%; I2 = 0%). Finally,tumour overgrowth was reported in 34 out of the 250 cases with pooled rate of tumour overgrowth of 11.2%(95%CI: 3.7%-22.1%; I2 = 82.2%). No funnel plot asymmetry to suggest publication bias(bias = 0.39,P = 0.78). In the sensitivity analysis all results were largely similar between the fixed and random effects models.CONCLUSION The double-layered nitinol stent provides immediate relief of malignant dysphagia with low rates of stent migration and tumour
基金Projects(50878191,51109092)supported by the National Natural Science Foundation of China
文摘Based on non-Darcian flow law described by exponent and threshold gradient within a double-layered soil, the classic theory of one-dimensional consolidation of double-layered soil was modified to consider the change of vertical total stress with depth and time together. Because of the complexity of governing equations, the numerical solutions were obtained in detail by finite difference method. Then, the numerical solutions were compared with the analytical solutions in condition that non-Darcian flow law was degenerated to Dary's law, and the comparison results show that numerical solutions are reliable. Finally, consolidation behavior of double-layered soil with different parameters was analyzed, and the results show that the consolidation rate of double-layered soil decreases with increasing the value of exponent and threshold of non-Darcian flow, and the exponent and threshold gradient of the first soil layer greatly influence the consolidation rate of double-layered soil. The larger the ratio of the equivalent water head of external load to the total thickness of double-layered soil, the larger the rate of the consolidation, and the similitude relationship in classical consolidation theory of double-layered soil is not satisfied. The other consolidation behavior of double-layered soil with non-Darcian flow is the same as that with Darcy's law.
基金Project(51578511)supported by the National Natural Science Foundation of China。
文摘To further investigate the one-dimensional(1D)rheological consolidation mechanism of double-layered soil,the fractional derivative Merchant model(FDMM)and the non-Darcian flow model with the non-Newtonian index are respectively introduced to describe the deformation of viscoelastic soil and the flow of pore water in the process of consolidation.Accordingly,an 1D rheological consolidation equation of double-layered soil is obtained,and its numerical analysis is performed by the implicit finite difference method.In order to verify its validity,the numerical solutions by the present method for some simplified cases are compared with the results in the related literature.Then,the influence of the revelent parameters on the rheological consolidation of double-layered soil are investigated.Numerical results indicate that the parameters of non-Darcian flow and FDMM of the first soil layer greatly influence the consolidation rate of double-layered soil.As the decrease of relative compressibility or the increase of relative permeability between the lower soil and the upper soil,the dissipation rate of excess pore water pressure and the settlement rate of the ground will be accelerated.Increasing the relative thickness of soil layer with high permeability or low compressibility will also accelerate the consolidation rate of double-layered soil.
基金National Natural Science Foundation of China(60532030)
文摘As an important scheme of future global mobile satellite communication systems to provide multimedia service, a Double-Layer Satellite Network （DLSN） with MEO satellites and LEO satellites is proposed. The Inter-Orbit-Links （IOLs） between layers is an essential factor, which affects the performances of the DLSN systems. Considering certain constellation parameters, the geometric characteristics of IOLs are described and the connectivity of MEO satellites and LEO satellites in the DLSN is analyzed. By computer simulation, the results show that IOLs should be selectively established according to certain parameters rather than the simple in-sight principle.
文摘The velocity structures of flow through vertically double-layered vegetation(VDLV)as well as single-layered rigid vegetation(SLV)were investigated computationally with a three-dimensional(3D)Reynolds stress turbulence model,using the computational fluid dynamics(CFD)code FLUENT.The detailed velocity distribution was explored with a varying initial Froude number(Fr),with consideration of the steady subcritical flow conditions of an inland tsunami.In VDLV flows,the numerical model successfully captured the inflection point in the profiles of mean streamwise velocities in the mixing-layer region around the top of short submerged vegetation.An upward and downward movement of flow occurred at the positions located just behind the tall and short vegetation,respectively.Overall,higher streamwise velocities were observed in the upper vegetation layer due to high porosity,with Pr=98%(sparse vegetation,where Pr is the porosity),as compared to those in the lower vegetation layer,which had comparatively low porosity,with Pr=91%(dense vegetation).A rising trend of velocities was found as the flow passed through the vegetation region,followed by a clear sawtooth distribution,as compared to the regions just upstream and downstream of vegetation where the flow was almost uniform.In VDLV flows,a rising trend in the flow resistance was observed with the increase in the initial Froude number,i.e.,Fr?0.67,0.70,and 0.73.However,the flow resistance in the case of SLV was relatively very low.The numerical results also show the flow structures within the vicinity of short and tall vegetation,which are difficult to attain through experimental measurements.
基金supported by the State Key Program of National Natural Science Foundation of China(Grant No.12132003)State Key Laboratory of Explosion Science and Technology(Grant No.QNKT20-07)。
文摘The time-sequenced damage behavior of the reactive projectile impacting double-layer plates is discussed.The analytical model considering the combined effect of kinetic and chemical energy is developed to reveal the damage mechanism.The influences of impact velocity and reactive projectile chemical characteristics on the damage effect are decoupled analyzed based on this model.These analyses indicate that the high energy releasing efficiency and fast reaction propagation velocity of the reactive projectile are conducive to enhancing the damage effect.The experiments with various reactive projectiles impact velocity increasing from 702 to 1385 m/s were conducted to verify this model.The experimental results presented that,the damage hole radius of the rear-plate increases with the increase of impact velocity.At the impact velocity of 1350 m/s,the radius of damage hole formed by PTFE/Al/Bi_(2)O_(3),PTFE/Al/MoO_(3),PTFE/Al/Fe_(2)O_(3)projectile on the rear-plate become smaller in sequence.These results are consistent with the analytical model prediction,demonstrating that this model can predict the damage effect quantitatively.This work is of constructive significance to the application of reactive projectiles.
文摘A simple, precise and accurate method was developed and validated for the determination of allicin release from alliin/alliinase double-layer tablets. According to Appendix XC Ⅱ of Chinese Pharmacopoeia 2010 edition Volume II, a small glass-method was adopted at the rotational speed of 100 r/min using 100 mL phosphate buffer （pH 6.8） as release medium. The release amount was determined by HPLC with a C18 column （250 mm × 4.6 mm, 5 μm） using the mobile phase consisting of methanol -0.4% carboxylic acid （65：35） at a flow rate of 1 mL/min and UV detection at 242 nm. The current method demonstrates good linearity over the range 4.052- 405.2 μg/mL （r2=0.9999） with an average recovery of 105.5%（RSD= 1.25%）. The accumulative release of alliin/alliinase double-layer tablets had good homogeneity for withinand betweenbatches. The method established is simple, accurate and repeatable for the determination of allicin release from alliin/alliinase double-layer tablets.
基金Project 50639010 and 50678032 supported by the National Natural Science Foundation of China
文摘The adsorption capacity of landfill liners containing granular activated carbon (GAC), or bentonite activated by acid, for Cr(VI) was investigated by batch testing. The results show that both GAC and activated bentonite could be used as sorptive amendments for trapping Cr(VI) in landfill liners. The Cr(VI) sorption to GAC and activated bentonite is much greater than Cr(VI) sorption to natural clay. The adsorption capacity of Cr(VI) onto all the soils increases with increasing temperature; adsorption capacity is also significantly influenced by soil-solid concentration. As the soil-solid concentration increases the adsorption capacity first decreases logarithmically, but then stabilizes when the soil-solid concentration exceeds a critical value (e.g. 400 g/L). Permeability tests were conducted in the laboratory. The results indicate that the hydraulic conductivity of landfill liners containing GAC or activated bentonite can meet the engineering requirement of 1 nm/s. One-dimensional transport simulations for Cr(VI) were performed to evaluate the effect of GAC and activated bentonite on landfill liners. The results of the simulations indicate that landfill liners containing GAC, or activated bentonite, significantly retard the transport of Cr(VI) relative to a conventional clay liner.
基金the financial support from"The Fundamental Research Funds for the Central Universities"(Grant No.2017XKQY052)
文摘To understand the mesoscopic mechanism of clayey soil in view of macroscopic behavior, it is essential to quantitatively calculate the electric double-layer repulsion between arbitrarily inclined clay particles.However, suitable calculation methods with high efficiency and accuracy are still rare at present in literature. Based on a great number of numerical calculations of the repulsion between two inclined platy clay particles, explicit empirical formulae for estimating electric double-layer repulsion between clay particles are put forward. Comparison between the empirical solutions and corresponding numerical results shows that the proposed formulae have a reasonable accuracy, and application of the presented formula is easy and efficient.
