Two-dimensional double-layer honeycomb(DLHC)materials are known for their diverse physical properties,but superconductivity has been a notably absent characteristic in this structure.We address this gap by investigati...Two-dimensional double-layer honeycomb(DLHC)materials are known for their diverse physical properties,but superconductivity has been a notably absent characteristic in this structure.We address this gap by investigating M_(2)N_(2)(M=Nb,Ta)with DLHC structure using first-principles calculations.Our results show that M_(2)N_(2)are stable and metallic,exhibiting superconducting behavior.Specifically,Nb_(2)N_(2)and Ta_(2)N_(2)display superconducting transition temperatures of 6.8 K and 8.8 K,respectively.Their electron-phonon coupling is predominantly driven by the coupling between metal d-orbitals and low-frequency metal-dominated vibration modes.Interestingly,two compounds also exhibit non-trivial band topology.Thus,M_(2)N_(2)are promising platforms for studying the interplay between topology and superconductivity and fill the gap in superconductivity research for DLHC materials.展开更多
The Savitzky-Golay(SG)filter,which employs polynomial least-squares approximations to smooth data and estimate derivatives,is widely used for processing noisy data.However,noise suppression by the SG filter is recogni...The Savitzky-Golay(SG)filter,which employs polynomial least-squares approximations to smooth data and estimate derivatives,is widely used for processing noisy data.However,noise suppression by the SG filter is recognized to be limited at data boundaries and high frequencies,which can significantly reduce the signal-to-noise ratio(SNR).To solve this problem,a novel method synergistically integrating Principal Component Analysis(PCA)with SG filtering is proposed in this paper.This approach avoids the is-sue of excessive smoothing associated with larger window sizes.The proposed PCA-SG filtering algorithm was applied to a CO gas sensing system based on Cavity Ring-Down Spectroscopy(CRDS).The perform-ance of the PCA-SG filtering algorithm is demonstrated through comparison with Moving Average Filtering(MAF),Wavelet Transformation(WT),Kalman Filtering(KF),and the SG filter.The results demonstrate that the proposed algorithm exhibits superior noise reduction capabilities compared to the other algorithms evaluated.The SNR of the ring-down signal was improved from 11.8612 dB to 29.0913 dB,and the stand-ard deviation of the extracted ring-down time constant was reduced from 0.037μs to 0.018μs.These results confirm that the proposed PCA-SG filtering algorithm effectively improves the smoothness of the ring-down curve data,demonstrating its feasibility.展开更多
Accurate estimation of the State of Charge(SOC),State of Health(SOH),and Terminal Resistance(TR)is crucial for the effective operation of Battery Management Systems(BMS)in lithium-ion batteries.This study conducts a c...Accurate estimation of the State of Charge(SOC),State of Health(SOH),and Terminal Resistance(TR)is crucial for the effective operation of Battery Management Systems(BMS)in lithium-ion batteries.This study conducts a comprehensive comparative analysis of four Kalman filter variants Extended Kalman Filter(EKF),Extended Kalman-Bucy Filter(EKBF),Unscented Kalman Filter(UKF),and Unscented Kalman-Bucy Filter(UKBF)under varying battery parameter conditions.These include temperature fluctuation,self-discharge,current direction,cell capacity,process noise,and measurement noise.Our findings reveal significant variations in the performance of SOC and SOH predictions across filters,emphasizing that UKF demonstrates superior robustness to noise,while EKF performs better under accurate system dynamics.The study underscores the need for adaptive filtering strategies that can dynamically adjust to evolving battery parameters,thereby enhancing BMS reliability and extending battery lifespan.展开更多
1 Introduction Recently,the increasing demand for advanced telecommunication systems has spurred extensive research into bandpass filters(BPFs),with particular emphasis on miniaturization,reduction of insertion loss(I...1 Introduction Recently,the increasing demand for advanced telecommunication systems has spurred extensive research into bandpass filters(BPFs),with particular emphasis on miniaturization,reduction of insertion loss(IL),and enhancement of upper stopband rejection(Huang et al.,2021;Snyder et al.,2021;Lin et al.,2023;Zeng et al.,2023).展开更多
In this study,a fifth-degree cubature particle filter(5CPF)is proposed to address the limited estimation accuracy in traditional particle filter algorithms for bearings-only tracking(BOT).This algorithm calculates the...In this study,a fifth-degree cubature particle filter(5CPF)is proposed to address the limited estimation accuracy in traditional particle filter algorithms for bearings-only tracking(BOT).This algorithm calculates the recommended density function by introducing a fifth-degree cubature Kalman filter algorithm to guide particle sampling,which effectively alleviates the problem of particle degradation and significantly improves the estimation accuracy of the filter.However,the 5CPF algorithm exhibits high computational complexity,particularly in scenarios with a large number of particles.Therefore,we propose the extended Kalman filter(EKF)-5CPF algorithm,which employs an EKF to replace the time update step for each particle in the 5CPF.This enhances the algorithm’s real-time capability while maintaining the high precision advantage of the 5CPF algorithm.In addition,we construct bearing-only dual-station and single-motion station target tracking systems,and the filtering performances of 5CPF and EKF-5CPF algorithms under different conditions are analyzed.The results show that both the 5CPF algorithm and EKF-5CPF have strong robustness and can adapt to different noise environments.Furthermore,both algorithms significantly outperform traditional nonlinear filtering algorithms in terms of convergence speed,tracking accuracy,and overall stability.展开更多
Color filters are essential components for optical modulation.However,conventional filters are restricted to operating exclusively in either reflective or transmissive mode.Furthermore,they suffer from limited UV and ...Color filters are essential components for optical modulation.However,conventional filters are restricted to operating exclusively in either reflective or transmissive mode.Furthermore,they suffer from limited UV and thermal stability,low color purity,and exhibit identical coloration on both surfaces.Herein,we propose a novel design strategy for trans-reflective color filters by integrating the absorptive properties of dye-doped polysulfone(PSU)with the diffractive capabilities of photonic crystals.This composite filter achieved broad-spectrum transmission with deep color outputs—yellow(0.410,0.510),magenta(0.446,0.231),and cyan(0.201,0.425)—closely aligned with standard color space coordinates.By tuning the refractive index of CeO_(2)@SiO_(2)nanoparticles to match dye-based PSU matrix,the transmittance of filters exceeded 70%.Moreover,dye-mediated absorption reduces the scattering light,thereby enhancing reflection color purity(full width at half maxima(FWHM)=25 nm)and producing vibrant blue,green,and red hues.The incorporation of UV-absorbing CeO_(2)@SiO_(2)nanoparticles effectively mitigated dye photodegradation,yielding exceptional UV stability(ΔT<2%under prolonged UV exposure).The filters also exhibited outstanding thermal stability(ΔT<1%after 30 min heat treatment at 230°C).This work establishes a robust materials design framework for multifunctional optical filters,advancing the development of highfidelity dual-mode color systems for next-generation display technologies.展开更多
Recommendation systems are an integral and indispensable part of every digital platform,as they can suggest content or items to users based on their respective needs.Collaborative filtering is a technique often used i...Recommendation systems are an integral and indispensable part of every digital platform,as they can suggest content or items to users based on their respective needs.Collaborative filtering is a technique often used in various studies,which produces recommendations by analyzing similarities between users and items based on their behavior.Although often used,traditional collaborative filtering techniques still face the main challenge of sparsity.Sparsity problems occur when the data in the system is sparse,meaning that only a portion of users provide feedback on some items,resulting in inaccurate recommendations generated by the system.To overcome this problem,we developed aHybrid Collaborative Filtering model based onMatrix Factorization andGradient Boosting(HCF-MFGB),a new hybrid approach.Our proposed model integrates SVD++,the XGBoost ensemble learning algorithm,and utilizes user demographic data and meta items.We utilize information,both explicitly and implicitly,to learn user preference patterns using SVD++.The XGBoost algorithm is used to create hundreds of decision trees incrementally,thereby improving model accuracy.Meanwhile,user demographic and meta-item data are clustered using the K-Means Clustering algorithm to capture similarities in user and item characteristics.This combination is designed to improve rating prediction accuracy by reducing reliance on minimal explicit rating data,while addressing sparsity issues in movie recommendation systems.The results of experiments on the MovieLens 100K,MovieLens 1M,and CiaoDVD datasets show significant improvements,outperforming various other baselinemodels in terms of RMSE and MAE.On theMovieLens 100K dataset,the HCF-MFGB model obtained an RMSE value of 0.853 and an MAE value of 0.674.On theMovieLens 1M dataset,the HCF-MFGB model obtained an RMSE value of 0.763 and an MAE value of 0.61.On the CiaoDCD dataset,the HCF-MFGB model achieved an RMSE value of 0.718 and an MAE value of 0.495.These results confirm a significant improvement in movie recommendation accuracy with the proposed approach.展开更多
This article presents an adaptive intelligent control strategy applied to a lumped-parameter evaporator model,i.e.,a simplified dynamic representation treating the evaporator as a single thermal node with uniform temp...This article presents an adaptive intelligent control strategy applied to a lumped-parameter evaporator model,i.e.,a simplified dynamic representation treating the evaporator as a single thermal node with uniform temperature distribution,suitable for control design due to its balance between physical fidelity and computational simplicity.The controller uses a wavelet-based neural proportional,integral,derivative(PID)controller with IIR filtering(infinite impulse response).The dynamic model captures the essential heat and mass transfer phenomena through a nonlinear energy balance,where the cooling capacity“Qevap”is expressed as a non-linear function of the compressor frequency and the temperature difference,specifically,Q_(evap)=k_(1)u(T_(in)−T_(e))with u as compressor frequency,Te evaporator temperature,and Tin inlet fluid temperature.The operating conditions of the system,in general terms,focus on the following variables,the overall thermal capacity is 1000 J/K,typical for small-capacity heat exchangers,The mass flow is 0.05 kg/s,typical for secondary liquid cooling circuits,the overall loss coefficient of 50 W/K that corresponds to small evaporators with partial insulation,the temperatures(inlet)of 10℃and the temperature of environment of 25℃,thermal load of 200 W that corresponds to a small-scaled air conditioning applications.To handle system nonlinearities and improve control performance,aMorlet wavelet-based neural network(Wavenet)is used to dynamically adjust the PID gains online.An IIR filter is incorporated to smooth the adaptive gains,improving stability and reducing oscillations.In contrast to prior wavelet-or neural-adaptive PID controllers in HVAC applications,which typically adjust gains without explicit filtering or not tailored to evaporator dynamics,this work introduces the first PID–Wavenet scheme augmented with an IIR-based stabilization layer,specifically designed to address the combined challenges of nonlinear evaporator behavior,gain oscillation,and real-time implementability.The proposed controller(PID-Wavenet+IIR)is implemented and validated inMATLAB/Simulink,demonstrating superior performance compared to a conventional PID tuned using Simulink’s auto-tuning function.Key results include a reduction in settling time from 13.3 to 8.2 s,a reduction in overshoot from 3.5%to 0.8%,a reduction in steady-state error from 0.12℃ to 0.02℃and a 13%reduction in energy overall consumption.The controller also exhibits greater robustness and adaptability under varying thermal loads.This explicit integration of wavelet-driven adaptation with IIR-filtered gain shaping constitutes the main methodological contribution and novelty of the work.These findings validate the effectiveness of the wavelet-based adaptive approach for advanced thermal management in refrigeration and HVAC systems,with potential applications in controlling variable-speed compressors,liquid chillers,and compact cooling units.展开更多
In order to establish the relationship between the measured dynamic response and the health status of long-span bridges, a double-layer model updating method for steel-concrete composite beam cable-stayed bridges is p...In order to establish the relationship between the measured dynamic response and the health status of long-span bridges, a double-layer model updating method for steel-concrete composite beam cable-stayed bridges is proposed. Measured frequencies are selected as the first-layer reference data, and the mass of the bridge deck, the grid density, the modulus of concrete and the ballast on the side span are modified by using a manual tuning technique. Measured global positioning system （GPS） data is selected as the second-layer reference data, and the degradation of the integral structure stiffness EI of the whole bridge is taken into account for the second-layer model updating by using the finite element iteration algorithm. The Nanpu Bridge in Shanghai is taken as a case to verify the applicability of the proposed model updating method. After the first-layer model updating, the standard deviation of modal frequencies is smaller than 7%. After the second-layer model updating, the error of the deflection of the mid-span is smaller than 10%. The integral structure stiffness of the whole bridge decreases about 20%. The research results show a good agreement between the calculated response and the measured response.展开更多
In order to increase the fatigue life (FL) of road wheels (RW), a kind of double layer rubber flange (DLRF) is put forward. It consists of two layers of rubber, where metal wires are laid in the inner layer and the ou...In order to increase the fatigue life (FL) of road wheels (RW), a kind of double layer rubber flange (DLRF) is put forward. It consists of two layers of rubber, where metal wires are laid in the inner layer and the outer layer has no inlaid metal wires. Stress, strain and temperature field of DLRF were calculated with ANSYS finite element analysis (FEA) software, FL of DLRF RW was also computed with fracture mechanics fatigue theory. The results of computation indicate that the heat generated in RW's rubber flange (RF) can be reduced by the use of DLRF, and the FL of RW can be increased without affecting the mechanical intensity of RW.展开更多
The aim of the study was to develop actarit double-layered osmotic pump tablets to overcome the weak points of actarit common tablets, such as short half-life and large plasma concentration fluctuations. Single factor...The aim of the study was to develop actarit double-layered osmotic pump tablets to overcome the weak points of actarit common tablets, such as short half-life and large plasma concentration fluctuations. Single factor experiment and orthogonal test were applied to optimize the formulation;the pharmacokinetic study was performed in beagle dogs adopting actarit common tablets as reference tablets. The optimal formulation was as follows: drug layer: 150 mg actarit, 240 mg PEO-N80, 50 mg NaCl;push layer: 140 mg PEO-WSR303, 20 mg NaCl;coating solution: 30 g cellulose acetate and 6 g PEG 4000 in 1000 ml 94% acetone solution, 60 mg coating weight gain. The pharmacokinetic study showed that T max was prolonged by the contrast of commercial common tablets with constant drug release rate, but the bioavailability was equivalent. And a good in vivo –in vitro correlation of the actarit osmotic pump tablets was also established. The designed actarit osmotic pump tablets can be applied for rheumatoid arthritis, proposing a promising replacement for the marked common products.展开更多
AIM To investigate the efficacy of double-layered covered stent in the treatment of malignant oesophageal obstructions.METHODS A systematic review and meta-analysis was performed following the PRISMA process. Pub Med(...AIM To investigate the efficacy of double-layered covered stent in the treatment of malignant oesophageal obstructions.METHODS A systematic review and meta-analysis was performed following the PRISMA process. Pub Med(Medline),EMBASE(Excerpta Medical Database),AMED(Allied and Complementary medicine Database),Scopus and online content,were searched for studies reporting on the Ni Ti-S polyurethane-covered double oesophageal stent for the treatment of malignant dysphagia. Weighted pooled outcomes were synthesized with a random effects model to account for clinical heterogeneity. All studies reporting the outcome of palliative management of dysphagia due to histologically confirmed malignant oesophageal obstruction using double-layered covered nitinol stent were included. The level of statistical significance was set at α = 0.05.RESULTS Six clinical studies comprising 250 patients in total were identified. Pooled technical success of stent insertion was 97.2%(95%CI: 94.8%-98.9%; I2 = 5.8%). Pooled complication rate was 27.6%(95%CI: 20.7%-35.2%; I2 = 41.9%). Weighted improvement of dysphagia on a scale of 0-5 scoring system was-2.00 [95%CI:-2.29%-(-1.72%); I2 = 87%]. Distal stent migration was documented in 10 out of the 250 cases examined.Pooled stent migration rate was 4.7%(95%CI: 2.5%-7.7%; I2 = 0%). Finally,tumour overgrowth was reported in 34 out of the 250 cases with pooled rate of tumour overgrowth of 11.2%(95%CI: 3.7%-22.1%; I2 = 82.2%). No funnel plot asymmetry to suggest publication bias(bias = 0.39,P = 0.78). In the sensitivity analysis all results were largely similar between the fixed and random effects models.CONCLUSION The double-layered nitinol stent provides immediate relief of malignant dysphagia with low rates of stent migration and tumour展开更多
Based on non-Darcian flow law described by exponent and threshold gradient within a double-layered soil, the classic theory of one-dimensional consolidation of double-layered soil was modified to consider the change o...Based on non-Darcian flow law described by exponent and threshold gradient within a double-layered soil, the classic theory of one-dimensional consolidation of double-layered soil was modified to consider the change of vertical total stress with depth and time together. Because of the complexity of governing equations, the numerical solutions were obtained in detail by finite difference method. Then, the numerical solutions were compared with the analytical solutions in condition that non-Darcian flow law was degenerated to Dary's law, and the comparison results show that numerical solutions are reliable. Finally, consolidation behavior of double-layered soil with different parameters was analyzed, and the results show that the consolidation rate of double-layered soil decreases with increasing the value of exponent and threshold of non-Darcian flow, and the exponent and threshold gradient of the first soil layer greatly influence the consolidation rate of double-layered soil. The larger the ratio of the equivalent water head of external load to the total thickness of double-layered soil, the larger the rate of the consolidation, and the similitude relationship in classical consolidation theory of double-layered soil is not satisfied. The other consolidation behavior of double-layered soil with non-Darcian flow is the same as that with Darcy's law.展开更多
An experiment was carried out to investigate the anti-ammonium shock load capacity of a biological aerated filter （BAF） composed of a double-layer bed. This bed was made up of a top layer of ceramic and a bottom lay...An experiment was carried out to investigate the anti-ammonium shock load capacity of a biological aerated filter （BAF） composed of a double-layer bed. This bed was made up of a top layer of ceramic and a bottom layer of zeolite. The experiment shows that the anti-ammonium shock load process can be divided into two processes： adsorption and release. In the adsorption process, the total removal efficiency of ammonia nitrogen by zeolite and ceramic was 94%. In the release process, the ammonia nitrogen concentration increased significantly and then gradually returned to the normal level four hours after the shock load. The results indicated that the double-layer BAF had a high level of adaptability to the short-term ammonium shock load and long-term operation. The main factors influencing the dynamic process of ammonia nitrogen adsorption were the filter bed height, ammonia nitrogen concentration of influent, and flow rate. The bed depth service time （BDST） model was used to predict the relationship between the filter bed height and breakthrough time at different flow rates, and the results are reliable.展开更多
The velocity structures of flow through vertically double-layered vegetation(VDLV)as well as single-layered rigid vegetation(SLV)were investigated computationally with a three-dimensional(3D)Reynolds stress turbulence...The velocity structures of flow through vertically double-layered vegetation(VDLV)as well as single-layered rigid vegetation(SLV)were investigated computationally with a three-dimensional(3D)Reynolds stress turbulence model,using the computational fluid dynamics(CFD)code FLUENT.The detailed velocity distribution was explored with a varying initial Froude number(Fr),with consideration of the steady subcritical flow conditions of an inland tsunami.In VDLV flows,the numerical model successfully captured the inflection point in the profiles of mean streamwise velocities in the mixing-layer region around the top of short submerged vegetation.An upward and downward movement of flow occurred at the positions located just behind the tall and short vegetation,respectively.Overall,higher streamwise velocities were observed in the upper vegetation layer due to high porosity,with Pr=98%(sparse vegetation,where Pr is the porosity),as compared to those in the lower vegetation layer,which had comparatively low porosity,with Pr=91%(dense vegetation).A rising trend of velocities was found as the flow passed through the vegetation region,followed by a clear sawtooth distribution,as compared to the regions just upstream and downstream of vegetation where the flow was almost uniform.In VDLV flows,a rising trend in the flow resistance was observed with the increase in the initial Froude number,i.e.,Fr?0.67,0.70,and 0.73.However,the flow resistance in the case of SLV was relatively very low.The numerical results also show the flow structures within the vicinity of short and tall vegetation,which are difficult to attain through experimental measurements.展开更多
To further investigate the one-dimensional(1D)rheological consolidation mechanism of double-layered soil,the fractional derivative Merchant model(FDMM)and the non-Darcian flow model with the non-Newtonian index are re...To further investigate the one-dimensional(1D)rheological consolidation mechanism of double-layered soil,the fractional derivative Merchant model(FDMM)and the non-Darcian flow model with the non-Newtonian index are respectively introduced to describe the deformation of viscoelastic soil and the flow of pore water in the process of consolidation.Accordingly,an 1D rheological consolidation equation of double-layered soil is obtained,and its numerical analysis is performed by the implicit finite difference method.In order to verify its validity,the numerical solutions by the present method for some simplified cases are compared with the results in the related literature.Then,the influence of the revelent parameters on the rheological consolidation of double-layered soil are investigated.Numerical results indicate that the parameters of non-Darcian flow and FDMM of the first soil layer greatly influence the consolidation rate of double-layered soil.As the decrease of relative compressibility or the increase of relative permeability between the lower soil and the upper soil,the dissipation rate of excess pore water pressure and the settlement rate of the ground will be accelerated.Increasing the relative thickness of soil layer with high permeability or low compressibility will also accelerate the consolidation rate of double-layered soil.展开更多
As an important scheme of future global mobile satellite communication systems to provide multimedia service, a Double-Layer Satellite Network （DLSN） with MEO satellites and LEO satellites is proposed. The Inter-Orb...As an important scheme of future global mobile satellite communication systems to provide multimedia service, a Double-Layer Satellite Network （DLSN） with MEO satellites and LEO satellites is proposed. The Inter-Orbit-Links （IOLs） between layers is an essential factor, which affects the performances of the DLSN systems. Considering certain constellation parameters, the geometric characteristics of IOLs are described and the connectivity of MEO satellites and LEO satellites in the DLSN is analyzed. By computer simulation, the results show that IOLs should be selectively established according to certain parameters rather than the simple in-sight principle.展开更多
The time-sequenced damage behavior of the reactive projectile impacting double-layer plates is discussed.The analytical model considering the combined effect of kinetic and chemical energy is developed to reveal the d...The time-sequenced damage behavior of the reactive projectile impacting double-layer plates is discussed.The analytical model considering the combined effect of kinetic and chemical energy is developed to reveal the damage mechanism.The influences of impact velocity and reactive projectile chemical characteristics on the damage effect are decoupled analyzed based on this model.These analyses indicate that the high energy releasing efficiency and fast reaction propagation velocity of the reactive projectile are conducive to enhancing the damage effect.The experiments with various reactive projectiles impact velocity increasing from 702 to 1385 m/s were conducted to verify this model.The experimental results presented that,the damage hole radius of the rear-plate increases with the increase of impact velocity.At the impact velocity of 1350 m/s,the radius of damage hole formed by PTFE/Al/Bi_(2)O_(3),PTFE/Al/MoO_(3),PTFE/Al/Fe_(2)O_(3)projectile on the rear-plate become smaller in sequence.These results are consistent with the analytical model prediction,demonstrating that this model can predict the damage effect quantitatively.This work is of constructive significance to the application of reactive projectiles.展开更多
This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double...This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double-layer charge liners were fabricated by using CVD to deposit tungsten layers on the inner surfaces of pure T2 copper liners.The microstructures of the tungsten layers were analyzed using a scanning electron microscope(SEM).The feasibility analysis was carried out by pulsed X-rays,slug-retrieval test and static penetration tests.The shaped charge jet forming and penetration law of inner tungsten-coated double-layer liner were studied by numerical simulation method.The results showed that the double-layer liners could form well-shaped jets.The errors between the X-ray test results and the numerical results were within 11.07%.A slug-retrieval test was found that the retrieved slug was similar to a numerically simulated slug.Compared with the traditional pure copper shaped charge jet,the penetration depth of the double-layer shaped charge liner increased by 11.4% and>10.8% respectively.In summary,the test results are good,and the numerical simulation is in good agreement with the test,which verified the feasibility of using the CVD method to fabricate double-layer charge liners with a high-density and high-strength refractory metal as the inner liner.展开更多
A simple, precise and accurate method was developed and validated for the determination of allicin release from alliin/alliinase double-layer tablets. According to Appendix XC Ⅱ of Chinese Pharmacopoeia 2010 edition ...A simple, precise and accurate method was developed and validated for the determination of allicin release from alliin/alliinase double-layer tablets. According to Appendix XC Ⅱ of Chinese Pharmacopoeia 2010 edition Volume II, a small glass-method was adopted at the rotational speed of 100 r/min using 100 mL phosphate buffer （pH 6.8） as release medium. The release amount was determined by HPLC with a C18 column （250 mm × 4.6 mm, 5 μm） using the mobile phase consisting of methanol -0.4% carboxylic acid （65：35） at a flow rate of 1 mL/min and UV detection at 242 nm. The current method demonstrates good linearity over the range 4.052- 405.2 μg/mL （r2=0.9999） with an average recovery of 105.5%（RSD= 1.25%）. The accumulative release of alliin/alliinase double-layer tablets had good homogeneity for withinand betweenbatches. The method established is simple, accurate and repeatable for the determination of allicin release from alliin/alliinase double-layer tablets.展开更多
基金Project supported by the National Natural Science Foundation of China(Grant Nos.12074213 and 11574108)the National Key R&D Program of China(Grant No.2022YFA1403103)+2 种基金the Major Basic Program of Natural Science Foundation of Shandong Province(Grant No.ZR2021ZD01)the Natural Science Foundation of Shandong Province(Grant No.ZR2023MA082)the Project of Introduction and Cultivation for Young Innovative Talents in Colleges and Universities of Shandong Province。
文摘Two-dimensional double-layer honeycomb(DLHC)materials are known for their diverse physical properties,but superconductivity has been a notably absent characteristic in this structure.We address this gap by investigating M_(2)N_(2)(M=Nb,Ta)with DLHC structure using first-principles calculations.Our results show that M_(2)N_(2)are stable and metallic,exhibiting superconducting behavior.Specifically,Nb_(2)N_(2)and Ta_(2)N_(2)display superconducting transition temperatures of 6.8 K and 8.8 K,respectively.Their electron-phonon coupling is predominantly driven by the coupling between metal d-orbitals and low-frequency metal-dominated vibration modes.Interestingly,two compounds also exhibit non-trivial band topology.Thus,M_(2)N_(2)are promising platforms for studying the interplay between topology and superconductivity and fill the gap in superconductivity research for DLHC materials.
文摘The Savitzky-Golay(SG)filter,which employs polynomial least-squares approximations to smooth data and estimate derivatives,is widely used for processing noisy data.However,noise suppression by the SG filter is recognized to be limited at data boundaries and high frequencies,which can significantly reduce the signal-to-noise ratio(SNR).To solve this problem,a novel method synergistically integrating Principal Component Analysis(PCA)with SG filtering is proposed in this paper.This approach avoids the is-sue of excessive smoothing associated with larger window sizes.The proposed PCA-SG filtering algorithm was applied to a CO gas sensing system based on Cavity Ring-Down Spectroscopy(CRDS).The perform-ance of the PCA-SG filtering algorithm is demonstrated through comparison with Moving Average Filtering(MAF),Wavelet Transformation(WT),Kalman Filtering(KF),and the SG filter.The results demonstrate that the proposed algorithm exhibits superior noise reduction capabilities compared to the other algorithms evaluated.The SNR of the ring-down signal was improved from 11.8612 dB to 29.0913 dB,and the stand-ard deviation of the extracted ring-down time constant was reduced from 0.037μs to 0.018μs.These results confirm that the proposed PCA-SG filtering algorithm effectively improves the smoothness of the ring-down curve data,demonstrating its feasibility.
基金supported by the Royal Academy of Engineering,UK,in the scheme of Distinguished International Associate(DIA-2424-5-134).
文摘Accurate estimation of the State of Charge(SOC),State of Health(SOH),and Terminal Resistance(TR)is crucial for the effective operation of Battery Management Systems(BMS)in lithium-ion batteries.This study conducts a comprehensive comparative analysis of four Kalman filter variants Extended Kalman Filter(EKF),Extended Kalman-Bucy Filter(EKBF),Unscented Kalman Filter(UKF),and Unscented Kalman-Bucy Filter(UKBF)under varying battery parameter conditions.These include temperature fluctuation,self-discharge,current direction,cell capacity,process noise,and measurement noise.Our findings reveal significant variations in the performance of SOC and SOH predictions across filters,emphasizing that UKF demonstrates superior robustness to noise,while EKF performs better under accurate system dynamics.The study underscores the need for adaptive filtering strategies that can dynamically adjust to evolving battery parameters,thereby enhancing BMS reliability and extending battery lifespan.
基金supported by the National Natural Science Foundation of China(No.62371263)the Postgraduate Research&Practice Innovation Program of Jiangsu Province(No.SJCK25_1995).
文摘1 Introduction Recently,the increasing demand for advanced telecommunication systems has spurred extensive research into bandpass filters(BPFs),with particular emphasis on miniaturization,reduction of insertion loss(IL),and enhancement of upper stopband rejection(Huang et al.,2021;Snyder et al.,2021;Lin et al.,2023;Zeng et al.,2023).
基金Supported by the Guangxi Special Program for Technological Innovation Guidance(No.GuiKeAC25069006).
文摘In this study,a fifth-degree cubature particle filter(5CPF)is proposed to address the limited estimation accuracy in traditional particle filter algorithms for bearings-only tracking(BOT).This algorithm calculates the recommended density function by introducing a fifth-degree cubature Kalman filter algorithm to guide particle sampling,which effectively alleviates the problem of particle degradation and significantly improves the estimation accuracy of the filter.However,the 5CPF algorithm exhibits high computational complexity,particularly in scenarios with a large number of particles.Therefore,we propose the extended Kalman filter(EKF)-5CPF algorithm,which employs an EKF to replace the time update step for each particle in the 5CPF.This enhances the algorithm’s real-time capability while maintaining the high precision advantage of the 5CPF algorithm.In addition,we construct bearing-only dual-station and single-motion station target tracking systems,and the filtering performances of 5CPF and EKF-5CPF algorithms under different conditions are analyzed.The results show that both the 5CPF algorithm and EKF-5CPF have strong robustness and can adapt to different noise environments.Furthermore,both algorithms significantly outperform traditional nonlinear filtering algorithms in terms of convergence speed,tracking accuracy,and overall stability.
基金supported by the Program of the National Natural Science Foundation of China(22238002)the Fundamental Research Funds for the Central Universities(DUT22-LAB610)Research and Innovation Team Project of Dalian University of Technology(DUT2022TB10).
文摘Color filters are essential components for optical modulation.However,conventional filters are restricted to operating exclusively in either reflective or transmissive mode.Furthermore,they suffer from limited UV and thermal stability,low color purity,and exhibit identical coloration on both surfaces.Herein,we propose a novel design strategy for trans-reflective color filters by integrating the absorptive properties of dye-doped polysulfone(PSU)with the diffractive capabilities of photonic crystals.This composite filter achieved broad-spectrum transmission with deep color outputs—yellow(0.410,0.510),magenta(0.446,0.231),and cyan(0.201,0.425)—closely aligned with standard color space coordinates.By tuning the refractive index of CeO_(2)@SiO_(2)nanoparticles to match dye-based PSU matrix,the transmittance of filters exceeded 70%.Moreover,dye-mediated absorption reduces the scattering light,thereby enhancing reflection color purity(full width at half maxima(FWHM)=25 nm)and producing vibrant blue,green,and red hues.The incorporation of UV-absorbing CeO_(2)@SiO_(2)nanoparticles effectively mitigated dye photodegradation,yielding exceptional UV stability(ΔT<2%under prolonged UV exposure).The filters also exhibited outstanding thermal stability(ΔT<1%after 30 min heat treatment at 230°C).This work establishes a robust materials design framework for multifunctional optical filters,advancing the development of highfidelity dual-mode color systems for next-generation display technologies.
基金funded by the Directorate General of Research and Development,Ministry of Higher Education,Science and Technology of the Republic of Indonesia,with grant number 2.6.63/UN32.14.1/LT/2025.
文摘Recommendation systems are an integral and indispensable part of every digital platform,as they can suggest content or items to users based on their respective needs.Collaborative filtering is a technique often used in various studies,which produces recommendations by analyzing similarities between users and items based on their behavior.Although often used,traditional collaborative filtering techniques still face the main challenge of sparsity.Sparsity problems occur when the data in the system is sparse,meaning that only a portion of users provide feedback on some items,resulting in inaccurate recommendations generated by the system.To overcome this problem,we developed aHybrid Collaborative Filtering model based onMatrix Factorization andGradient Boosting(HCF-MFGB),a new hybrid approach.Our proposed model integrates SVD++,the XGBoost ensemble learning algorithm,and utilizes user demographic data and meta items.We utilize information,both explicitly and implicitly,to learn user preference patterns using SVD++.The XGBoost algorithm is used to create hundreds of decision trees incrementally,thereby improving model accuracy.Meanwhile,user demographic and meta-item data are clustered using the K-Means Clustering algorithm to capture similarities in user and item characteristics.This combination is designed to improve rating prediction accuracy by reducing reliance on minimal explicit rating data,while addressing sparsity issues in movie recommendation systems.The results of experiments on the MovieLens 100K,MovieLens 1M,and CiaoDVD datasets show significant improvements,outperforming various other baselinemodels in terms of RMSE and MAE.On theMovieLens 100K dataset,the HCF-MFGB model obtained an RMSE value of 0.853 and an MAE value of 0.674.On theMovieLens 1M dataset,the HCF-MFGB model obtained an RMSE value of 0.763 and an MAE value of 0.61.On the CiaoDCD dataset,the HCF-MFGB model achieved an RMSE value of 0.718 and an MAE value of 0.495.These results confirm a significant improvement in movie recommendation accuracy with the proposed approach.
文摘This article presents an adaptive intelligent control strategy applied to a lumped-parameter evaporator model,i.e.,a simplified dynamic representation treating the evaporator as a single thermal node with uniform temperature distribution,suitable for control design due to its balance between physical fidelity and computational simplicity.The controller uses a wavelet-based neural proportional,integral,derivative(PID)controller with IIR filtering(infinite impulse response).The dynamic model captures the essential heat and mass transfer phenomena through a nonlinear energy balance,where the cooling capacity“Qevap”is expressed as a non-linear function of the compressor frequency and the temperature difference,specifically,Q_(evap)=k_(1)u(T_(in)−T_(e))with u as compressor frequency,Te evaporator temperature,and Tin inlet fluid temperature.The operating conditions of the system,in general terms,focus on the following variables,the overall thermal capacity is 1000 J/K,typical for small-capacity heat exchangers,The mass flow is 0.05 kg/s,typical for secondary liquid cooling circuits,the overall loss coefficient of 50 W/K that corresponds to small evaporators with partial insulation,the temperatures(inlet)of 10℃and the temperature of environment of 25℃,thermal load of 200 W that corresponds to a small-scaled air conditioning applications.To handle system nonlinearities and improve control performance,aMorlet wavelet-based neural network(Wavenet)is used to dynamically adjust the PID gains online.An IIR filter is incorporated to smooth the adaptive gains,improving stability and reducing oscillations.In contrast to prior wavelet-or neural-adaptive PID controllers in HVAC applications,which typically adjust gains without explicit filtering or not tailored to evaporator dynamics,this work introduces the first PID–Wavenet scheme augmented with an IIR-based stabilization layer,specifically designed to address the combined challenges of nonlinear evaporator behavior,gain oscillation,and real-time implementability.The proposed controller(PID-Wavenet+IIR)is implemented and validated inMATLAB/Simulink,demonstrating superior performance compared to a conventional PID tuned using Simulink’s auto-tuning function.Key results include a reduction in settling time from 13.3 to 8.2 s,a reduction in overshoot from 3.5%to 0.8%,a reduction in steady-state error from 0.12℃ to 0.02℃and a 13%reduction in energy overall consumption.The controller also exhibits greater robustness and adaptability under varying thermal loads.This explicit integration of wavelet-driven adaptation with IIR-filtered gain shaping constitutes the main methodological contribution and novelty of the work.These findings validate the effectiveness of the wavelet-based adaptive approach for advanced thermal management in refrigeration and HVAC systems,with potential applications in controlling variable-speed compressors,liquid chillers,and compact cooling units.
基金The Special Project of the Ministry of Construction ofChina (No.20060909).
文摘In order to establish the relationship between the measured dynamic response and the health status of long-span bridges, a double-layer model updating method for steel-concrete composite beam cable-stayed bridges is proposed. Measured frequencies are selected as the first-layer reference data, and the mass of the bridge deck, the grid density, the modulus of concrete and the ballast on the side span are modified by using a manual tuning technique. Measured global positioning system （GPS） data is selected as the second-layer reference data, and the degradation of the integral structure stiffness EI of the whole bridge is taken into account for the second-layer model updating by using the finite element iteration algorithm. The Nanpu Bridge in Shanghai is taken as a case to verify the applicability of the proposed model updating method. After the first-layer model updating, the standard deviation of modal frequencies is smaller than 7%. After the second-layer model updating, the error of the deflection of the mid-span is smaller than 10%. The integral structure stiffness of the whole bridge decreases about 20%. The research results show a good agreement between the calculated response and the measured response.
文摘In order to increase the fatigue life (FL) of road wheels (RW), a kind of double layer rubber flange (DLRF) is put forward. It consists of two layers of rubber, where metal wires are laid in the inner layer and the outer layer has no inlaid metal wires. Stress, strain and temperature field of DLRF were calculated with ANSYS finite element analysis (FEA) software, FL of DLRF RW was also computed with fracture mechanics fatigue theory. The results of computation indicate that the heat generated in RW's rubber flange (RF) can be reduced by the use of DLRF, and the FL of RW can be increased without affecting the mechanical intensity of RW.
文摘The aim of the study was to develop actarit double-layered osmotic pump tablets to overcome the weak points of actarit common tablets, such as short half-life and large plasma concentration fluctuations. Single factor experiment and orthogonal test were applied to optimize the formulation;the pharmacokinetic study was performed in beagle dogs adopting actarit common tablets as reference tablets. The optimal formulation was as follows: drug layer: 150 mg actarit, 240 mg PEO-N80, 50 mg NaCl;push layer: 140 mg PEO-WSR303, 20 mg NaCl;coating solution: 30 g cellulose acetate and 6 g PEG 4000 in 1000 ml 94% acetone solution, 60 mg coating weight gain. The pharmacokinetic study showed that T max was prolonged by the contrast of commercial common tablets with constant drug release rate, but the bioavailability was equivalent. And a good in vivo –in vitro correlation of the actarit osmotic pump tablets was also established. The designed actarit osmotic pump tablets can be applied for rheumatoid arthritis, proposing a promising replacement for the marked common products.
文摘AIM To investigate the efficacy of double-layered covered stent in the treatment of malignant oesophageal obstructions.METHODS A systematic review and meta-analysis was performed following the PRISMA process. Pub Med(Medline),EMBASE(Excerpta Medical Database),AMED(Allied and Complementary medicine Database),Scopus and online content,were searched for studies reporting on the Ni Ti-S polyurethane-covered double oesophageal stent for the treatment of malignant dysphagia. Weighted pooled outcomes were synthesized with a random effects model to account for clinical heterogeneity. All studies reporting the outcome of palliative management of dysphagia due to histologically confirmed malignant oesophageal obstruction using double-layered covered nitinol stent were included. The level of statistical significance was set at α = 0.05.RESULTS Six clinical studies comprising 250 patients in total were identified. Pooled technical success of stent insertion was 97.2%(95%CI: 94.8%-98.9%; I2 = 5.8%). Pooled complication rate was 27.6%(95%CI: 20.7%-35.2%; I2 = 41.9%). Weighted improvement of dysphagia on a scale of 0-5 scoring system was-2.00 [95%CI:-2.29%-(-1.72%); I2 = 87%]. Distal stent migration was documented in 10 out of the 250 cases examined.Pooled stent migration rate was 4.7%(95%CI: 2.5%-7.7%; I2 = 0%). Finally,tumour overgrowth was reported in 34 out of the 250 cases with pooled rate of tumour overgrowth of 11.2%(95%CI: 3.7%-22.1%; I2 = 82.2%). No funnel plot asymmetry to suggest publication bias(bias = 0.39,P = 0.78). In the sensitivity analysis all results were largely similar between the fixed and random effects models.CONCLUSION The double-layered nitinol stent provides immediate relief of malignant dysphagia with low rates of stent migration and tumour
基金Projects(50878191,51109092)supported by the National Natural Science Foundation of China
文摘Based on non-Darcian flow law described by exponent and threshold gradient within a double-layered soil, the classic theory of one-dimensional consolidation of double-layered soil was modified to consider the change of vertical total stress with depth and time together. Because of the complexity of governing equations, the numerical solutions were obtained in detail by finite difference method. Then, the numerical solutions were compared with the analytical solutions in condition that non-Darcian flow law was degenerated to Dary's law, and the comparison results show that numerical solutions are reliable. Finally, consolidation behavior of double-layered soil with different parameters was analyzed, and the results show that the consolidation rate of double-layered soil decreases with increasing the value of exponent and threshold of non-Darcian flow, and the exponent and threshold gradient of the first soil layer greatly influence the consolidation rate of double-layered soil. The larger the ratio of the equivalent water head of external load to the total thickness of double-layered soil, the larger the rate of the consolidation, and the similitude relationship in classical consolidation theory of double-layered soil is not satisfied. The other consolidation behavior of double-layered soil with non-Darcian flow is the same as that with Darcy's law.
基金supported by the Major Science and Technology Program for Water Pollution Control and Treatment of China(Grant No.2009ZX07317)
文摘An experiment was carried out to investigate the anti-ammonium shock load capacity of a biological aerated filter （BAF） composed of a double-layer bed. This bed was made up of a top layer of ceramic and a bottom layer of zeolite. The experiment shows that the anti-ammonium shock load process can be divided into two processes： adsorption and release. In the adsorption process, the total removal efficiency of ammonia nitrogen by zeolite and ceramic was 94%. In the release process, the ammonia nitrogen concentration increased significantly and then gradually returned to the normal level four hours after the shock load. The results indicated that the double-layer BAF had a high level of adaptability to the short-term ammonium shock load and long-term operation. The main factors influencing the dynamic process of ammonia nitrogen adsorption were the filter bed height, ammonia nitrogen concentration of influent, and flow rate. The bed depth service time （BDST） model was used to predict the relationship between the filter bed height and breakthrough time at different flow rates, and the results are reliable.
文摘The velocity structures of flow through vertically double-layered vegetation(VDLV)as well as single-layered rigid vegetation(SLV)were investigated computationally with a three-dimensional(3D)Reynolds stress turbulence model,using the computational fluid dynamics(CFD)code FLUENT.The detailed velocity distribution was explored with a varying initial Froude number(Fr),with consideration of the steady subcritical flow conditions of an inland tsunami.In VDLV flows,the numerical model successfully captured the inflection point in the profiles of mean streamwise velocities in the mixing-layer region around the top of short submerged vegetation.An upward and downward movement of flow occurred at the positions located just behind the tall and short vegetation,respectively.Overall,higher streamwise velocities were observed in the upper vegetation layer due to high porosity,with Pr=98%(sparse vegetation,where Pr is the porosity),as compared to those in the lower vegetation layer,which had comparatively low porosity,with Pr=91%(dense vegetation).A rising trend of velocities was found as the flow passed through the vegetation region,followed by a clear sawtooth distribution,as compared to the regions just upstream and downstream of vegetation where the flow was almost uniform.In VDLV flows,a rising trend in the flow resistance was observed with the increase in the initial Froude number,i.e.,Fr?0.67,0.70,and 0.73.However,the flow resistance in the case of SLV was relatively very low.The numerical results also show the flow structures within the vicinity of short and tall vegetation,which are difficult to attain through experimental measurements.
基金Project(51578511)supported by the National Natural Science Foundation of China。
文摘To further investigate the one-dimensional(1D)rheological consolidation mechanism of double-layered soil,the fractional derivative Merchant model(FDMM)and the non-Darcian flow model with the non-Newtonian index are respectively introduced to describe the deformation of viscoelastic soil and the flow of pore water in the process of consolidation.Accordingly,an 1D rheological consolidation equation of double-layered soil is obtained,and its numerical analysis is performed by the implicit finite difference method.In order to verify its validity,the numerical solutions by the present method for some simplified cases are compared with the results in the related literature.Then,the influence of the revelent parameters on the rheological consolidation of double-layered soil are investigated.Numerical results indicate that the parameters of non-Darcian flow and FDMM of the first soil layer greatly influence the consolidation rate of double-layered soil.As the decrease of relative compressibility or the increase of relative permeability between the lower soil and the upper soil,the dissipation rate of excess pore water pressure and the settlement rate of the ground will be accelerated.Increasing the relative thickness of soil layer with high permeability or low compressibility will also accelerate the consolidation rate of double-layered soil.
基金National Natural Science Foundation of China(60532030)
文摘As an important scheme of future global mobile satellite communication systems to provide multimedia service, a Double-Layer Satellite Network （DLSN） with MEO satellites and LEO satellites is proposed. The Inter-Orbit-Links （IOLs） between layers is an essential factor, which affects the performances of the DLSN systems. Considering certain constellation parameters, the geometric characteristics of IOLs are described and the connectivity of MEO satellites and LEO satellites in the DLSN is analyzed. By computer simulation, the results show that IOLs should be selectively established according to certain parameters rather than the simple in-sight principle.
基金supported by the State Key Program of National Natural Science Foundation of China(Grant No.12132003)State Key Laboratory of Explosion Science and Technology(Grant No.QNKT20-07)。
文摘The time-sequenced damage behavior of the reactive projectile impacting double-layer plates is discussed.The analytical model considering the combined effect of kinetic and chemical energy is developed to reveal the damage mechanism.The influences of impact velocity and reactive projectile chemical characteristics on the damage effect are decoupled analyzed based on this model.These analyses indicate that the high energy releasing efficiency and fast reaction propagation velocity of the reactive projectile are conducive to enhancing the damage effect.The experiments with various reactive projectiles impact velocity increasing from 702 to 1385 m/s were conducted to verify this model.The experimental results presented that,the damage hole radius of the rear-plate increases with the increase of impact velocity.At the impact velocity of 1350 m/s,the radius of damage hole formed by PTFE/Al/Bi_(2)O_(3),PTFE/Al/MoO_(3),PTFE/Al/Fe_(2)O_(3)projectile on the rear-plate become smaller in sequence.These results are consistent with the analytical model prediction,demonstrating that this model can predict the damage effect quantitatively.This work is of constructive significance to the application of reactive projectiles.
基金funded by the China Postdoctoral Science Foundation(Grant No.2022M721614)the opening project of State Key Laboratory of Explosion Science and Technology,Beijing Institute of Technology(Grant No.KFJJ23-07M)。
文摘This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double-layer charge liners were fabricated by using CVD to deposit tungsten layers on the inner surfaces of pure T2 copper liners.The microstructures of the tungsten layers were analyzed using a scanning electron microscope(SEM).The feasibility analysis was carried out by pulsed X-rays,slug-retrieval test and static penetration tests.The shaped charge jet forming and penetration law of inner tungsten-coated double-layer liner were studied by numerical simulation method.The results showed that the double-layer liners could form well-shaped jets.The errors between the X-ray test results and the numerical results were within 11.07%.A slug-retrieval test was found that the retrieved slug was similar to a numerically simulated slug.Compared with the traditional pure copper shaped charge jet,the penetration depth of the double-layer shaped charge liner increased by 11.4% and>10.8% respectively.In summary,the test results are good,and the numerical simulation is in good agreement with the test,which verified the feasibility of using the CVD method to fabricate double-layer charge liners with a high-density and high-strength refractory metal as the inner liner.
文摘A simple, precise and accurate method was developed and validated for the determination of allicin release from alliin/alliinase double-layer tablets. According to Appendix XC Ⅱ of Chinese Pharmacopoeia 2010 edition Volume II, a small glass-method was adopted at the rotational speed of 100 r/min using 100 mL phosphate buffer （pH 6.8） as release medium. The release amount was determined by HPLC with a C18 column （250 mm × 4.6 mm, 5 μm） using the mobile phase consisting of methanol -0.4% carboxylic acid （65：35） at a flow rate of 1 mL/min and UV detection at 242 nm. The current method demonstrates good linearity over the range 4.052- 405.2 μg/mL （r2=0.9999） with an average recovery of 105.5%（RSD= 1.25%）. The accumulative release of alliin/alliinase double-layer tablets had good homogeneity for withinand betweenbatches. The method established is simple, accurate and repeatable for the determination of allicin release from alliin/alliinase double-layer tablets.
