The buoyancy-induced flow constitutes a core scientific issue for thermal management of electronic devices and thermal design of energy systems,where accurate characterization of flow and heat transfer is essential to...The buoyancy-induced flow constitutes a core scientific issue for thermal management of electronic devices and thermal design of energy systems,where accurate characterization of flow and heat transfer is essential to improve thermal efficiency.In this work,buoyancy-induced flow above two heating elements flush-mounted at the bottom of a square enclosure containing air is numerically investigated over a range of Rayleigh numbers(0<Ra≤1.5×10^(8)),with a focus on equal and unequal heat flux conditions under a constraint of constant total thermal energy input.Distinct flow transitions are observed in both cases,leading to the identification of three flow regimes:Steady,periodic unsteady,and chaotic unsteady.Two types of periodic flows are distinguished,in which the first is a periodic flow dominated by a fundamental frequency(FF)and its integer-multiple frequencies(INTMF),while the second is a more complex periodic flow featuring FF,INTMF,and their sub-harmonics.The transitions between these regimes are affected by the relative heat flux of the two heaters.When the heat flux of the two heaters is unequal,the range of Rayleigh numbers corresponding to periodic flow is suppressed.It is also found that the time-averaged maximum temperature of the strong heater increases more rapidly with Ra,while that of the weak heater increases more slowly,reflecting the interaction between buoyancy-driven flow dynamics and asymmetric heat input.Analysis of the time-averaged Nusselt number demonstrates that heat dissipation from the isothermal walls remains roughly equivalent,even when the heat flux of the two heaters differs by a factor of two.These findings highlight the critical roles of Rayleigh number,the number of heaters,and the heat flux ratio of the heaters in determining heat transfer and flow characteristics for buoyancy-driven convection systems,providing important theoretical support and design references for engineering scenarios such as electronic devices and design of new energy systems.展开更多
This study involved numerical simulations of a double tube heat exchanger using the ANSYS FLUENT programversion 22.The study aims to examine methods for minimizing pressure loss and consequently enhancing the thermal ...This study involved numerical simulations of a double tube heat exchanger using the ANSYS FLUENT programversion 22.The study aims to examine methods for minimizing pressure loss and consequently enhancing the thermal performance index(TPI)of a heat exchanger fitted with wavy edge tape that is a heat recovery system(the hot air in simulation instead of t heat from the exhaust gases of the brick factory furnaces and return it to warm the heavy fuel oil by substituting the electrical heater with a heat exchanger to recuperate waste heat from the flue gases,so elevating the temperature of Heavy fuel oil(HFO)to inject from the roof nozzles of combustion chamber of the furnace furthermore reducing cost(by finding the optimal design of wavy edge tape))and energy consumption.Air was selected as the hot gas in the inner pipe instead of furnace exhaust gases due to their similar thermal characteristics.A numerical analysis was conducted to create a novel wavy edge tape with varying widths(50%Di,75%Di,and 95%Di),lengths(1000,1200,1400)mm,amplitudes(5,10,15)mm,and periods of wavy length(5,10,15)mm.The flow rate of the outer pipe fluid(oil)ranges from(0.06 to 0.1)kg/s,while the velocity of the hot fluid(air)varies from(1 to 27)m/s,Re_(air)(6957 to 187,837).The entrance temperature of the hot fluid can be either(200,225,and 250)℃.The study finds that wavy edge tape tubes are more effective than smooth tubes in terms of oil outlet temperature;results revealed that an increase in the oil mass flow rate leads to a decrease in the oil outlet temperature and an increase in the heat transfer rate,at the air temperature 250℃.Additionally,the results indicate that increasing the width,length,and amplitude also leads to an increase in the oil outlet temperature of(94-94.12)℃,the pressure drop of(568.3)Pa,and the Nusselt number(65.7-66.5)respectively on the oil side.Finally,the heat exchanger’s best thermal performance index was found by investigating temperature contour at amplitude(A=5),period(p=15),width(w=75%Di),and length(L=1200 mm).The values for these parameters are,in order(1.02,1.025,1.02,and 1.0077).展开更多
Double pipe heat exchangers(DPHEs)are normally utilized in various manufacturing uses owing to their simple design and low maintenance requirements.For that,performance enhancement by improved heat transfer is ongoing...Double pipe heat exchangers(DPHEs)are normally utilized in various manufacturing uses owing to their simple design and low maintenance requirements.For that,performance enhancement by improved heat transfer is ongoing.Air injections are a good strategy for enhancing the thermal performance of the DPHE.In the present work,the influence of air bubble injection in a DPHE was experimentally investigated,and the system’s hydrothermal performance improvement parameters were evaluated.Two modes were designed,manufactured,and used to conduct the experiments.The first mode was conducted with no air injection,named a single phase mode,while in the second mode,air was injected into the annulus of DPHE throughout different perforated rings on the side of the annular.Three different ring types were used and coded as R-1,R-2,and R-3,with an added case of insertion of the three rings inside the annulus.The airflow rate was fixed at 1.5 LPM with a 25○C inlet temperature.Also,the hot water rate in the inner pipe was maintained continuously at 3 LPM with a controlled 70○C temperature at the inlet.Five different cold water flow rates,3,3.5,4,4.5,and 5 LPM,in the annulus,were considered with a controlled inlet temperature at 17○C.Additionally,the effectiveness of the heat exchanger,the number of transfer units(NTU),and the overall heat transfer were predicted and considered for performance evaluation and comparison.The outcomes proved that the injection of air and the bubbly flow creation in the heat exchanger’s hot side is an effective method to strengthen the DPHE performance.Moreover,the total heat transfer coefficient was enhanced by 41%in R-1,58.8%in R-2,and 40.1%in R-3 at 4 LPM of cold water.The optimal ring,which yielded the most improvement,was R-2,achieving a 65%improvement in NTU,with a maximum enhancement in effectiveness of 56%.展开更多
The dynamic thermal process during double-sided asymmetrical TIG backing welding of large thick plates （ 1 000 mm×700 mm×50 mm） is numerically simulated using MSC. MARC. The effect of arc distance on the t...The dynamic thermal process during double-sided asymmetrical TIG backing welding of large thick plates （ 1 000 mm×700 mm×50 mm） is numerically simulated using MSC. MARC. The effect of arc distance on the thermal cycle in weld zone during double-sided asymmetrical T1G backing welding is investigated. The results show that the workpiece experiences double-peak thermal cycle in double-sided asymmetrical TIG backing welding. On the one hand, the fore arc has the pre- heating effect on the rear pass, and the pre-heating temperature depends on the distance between the double arcs, the heat input of fore arc, and the initial temperature of workpiece. On the other hand, the rear arc has the post-heating effect on the fore pass. The mutual effects of two heat sources decrease with the increase of arc distance.展开更多
In present work,a helical double tube heat exchanger is proposed in which an advanced turbulator with blades,semi-conical part,and two holes is inserted in inner section.Two geometrical parameters,including angle of t...In present work,a helical double tube heat exchanger is proposed in which an advanced turbulator with blades,semi-conical part,and two holes is inserted in inner section.Two geometrical parameters,including angle of turbulator’s blades(θ) and number of turbulator’s blades(N),are considered.Results indicated that firstly,the best thermal stratification is achieved at θ=180°.Furthermore,at the lowest studied mass flow rate(m = 8 × 10^(-3) kg/s),heat transfer coefficient of turbulator with blade angle of 180° is 130.77%,25%,and 36.36% higher than cases including without turbulator,with turbulator with blade angle of θ =240°,and θ =360°,respectively.Moreover,case with N=12 showed the highest overall performance.At the highest studied mass flow rate(m = 5.842 × 10^(-2) kg/s),heat transfer coefficient for case with N=12 is up to 54.76%,27.45%,and 6.56% higher than cases including without turbulator,with turbulator with N=6,and with turbulator with N=9,respectively.展开更多
In order to analyze the maximum power density error with different heat flux distribution parameter values for double ellipsoidal heat source model, a general expression of double ellipsoidal heat source model was der...In order to analyze the maximum power density error with different heat flux distribution parameter values for double ellipsoidal heat source model, a general expression of double ellipsoidal heat source model was derived .front Goldak double ellipsoidal heat source model, and the error of maximum power density was analyzed under this foundation. The calculation error of thermal cycling parameters caused by the maximum power density error was compared quantitatively by numerical simulation. The results show that for guarantee the accuracy of welding numerical simulation, it is better to introduce an error correction coefficient into the Goldak double ellipsoidal heat source model expression. And, heat flux distribution parameter should get higher value for the higher power density welding methods.展开更多
A heat exchanger’s performance depends heavily on the operating fluid’s transfer of heat capacity and thermal conductivity.Adding nanoparticles of high thermal conductivity materials is a significant way to enhance ...A heat exchanger’s performance depends heavily on the operating fluid’s transfer of heat capacity and thermal conductivity.Adding nanoparticles of high thermal conductivity materials is a significant way to enhance the heat transfer fluid’s thermal conductivity.This research used engine oil containing alumina(Al_(2)O_(3))nanoparticles and copper oxide(CuO)to test whether or not the heat exchanger’s efficiency could be improved.To establish the most effective elements for heat transfer enhancement,the heat exchangers thermal performance was tested at 0.05%and 0.1%concentrations for Al_(2)O_(3)and CuO nanoparticles.The simulation results showed that the percentage increase in Nusselt number(Nu)for nanofluid at 0.05%particle concentration compared to pure oil was 9.71%for CuO nanofluids and 6.7%for Al_(2)O_(3)nanofluids.At 0.1%concentration,the enhancement percentage in Nu was approximately 23%for CuO and 18.67%for Al_(2)O_(3)nanofluids,respectively.At a concentration of 0.1%,CuO nanofluid increased the LMTD and overall heat transfer coefficient(U)by 7.24 and 5.91%respectively.Both the overall heat transfer coefficient(U)and the heat transfer coefficient(hn)for CuO nanofluid at a concentration of 0.1%increased by 5.91%and 10.68%,respectively.The effectiveness(εn)of a heat exchanger was increased by roughly 4.09%with the use of CuO nanofluid in comparison to Al_(2)O_(3)at a concentration of 0.1%.The amount of exergy destruction in DTHX goes down as Re and volume fractions go up.Moreover,at 0.05%and 0.1%nanoparticle concentrations,the percentage increase in dimensionless exergy is 10.55%and 13.08%,respectively.Finally,adding the CuO and Al_(2)O_(3)nanoparticles improved the thermal conductivity of the main fluid(oil),resulting in a considerable increase in the thermal performance and rate of heat transfer of a heat exchanger.展开更多
Objective: in view of the defects of traditional moxibustion therapeutic apparatus, such as open fire heating is prone to scald and unstable control transmission, a portable moxibustion heating therapeutic apparatus b...Objective: in view of the defects of traditional moxibustion therapeutic apparatus, such as open fire heating is prone to scald and unstable control transmission, a portable moxibustion heating therapeutic apparatus based on Arduino control board for scapulohumeral periarthritis and rotator cuff disease was designed, and its value in the treatment of scapulohumeral periarthritis, rotator cuff disease and rotator cuff injury was evaluated. Methods: ATmega328 single chip microcomputer was used as the control core of the therapeutic instrument, which was composed of DS18B20 temperature sensor, graphene new heating module and low burning point patch made of finished wormwood. Results: the requirements of portable miniaturization were met. The therapeutic effect of Ai Rong was fully released through software program control and dual combined heating. The therapeutic instrument was fully automatic, and the therapeutic efficiency was improved. Conclusion: the therapeutic instrument has obvious overall effect, low cost, and can be used anytime and anywhere in the hospital, which is simple and safe to operate. It is an effective treatment device for shoulder periarthritis, shoulder sleeve disease, shoulder sleeve injury and other common diseases. It has high application value and is worth popularizing.展开更多
With the energy problem becoming increasingly severe,industrial energy efficiency issues need to be solved urgently.The tube and shell heat exchanger,as the most widely used device for energy recovery and utilisation,...With the energy problem becoming increasingly severe,industrial energy efficiency issues need to be solved urgently.The tube and shell heat exchanger,as the most widely used device for energy recovery and utilisation,its optimal design has become a significantly important research topic.Optimal design solves the tediousness of traditional design and can easily and accurately give the desired design results.Several industrial heat duty targets and pressure drop limitations for the design of shell-and-tube heat exchangers,such as high heat transfer efficiency,large temperature correction coefficient,and high capacity,cannot be met by single-shell units and require series or parallel arrangements.This paper uses Set Trimming to optimize the design of double shell and tube heat exchangers,assuming the possibility of series,parallel,or series-parallel arrangements.Minimum heat transfer area and minimum total annualized cost are used as objective functions to optimize the design of a single or double-shell heat exchanger that better meets the objectives.展开更多
Mathematical models of three-dimensional temperature fields in underwater welding with moving heat sources are built. Double ellipsoid Gauss model is proposed as heat sources models. Several factors which affect the t...Mathematical models of three-dimensional temperature fields in underwater welding with moving heat sources are built. Double ellipsoid Gauss model is proposed as heat sources models. Several factors which affect the temperature fields of underwater welding are analyzed. Water has little influence on thermal efftciency. Water convection coefftcient varies with the temperature difference between the water and the workpiece , and water convection makes molten pool freeze quickly. With the increase of water depth, the dimensions of heat sources model should be reduced as arc shrinks. Finite element technology is used to solve mathematical models. ANSYS software is used as finite element tool, and ANSYS Parametric Design Language is used to develop subprograms for loading the moving heat sources and the various convection coefftcients. Experiment results show that computational results by using double ellipsoid Gauss heat sources model accord well with the experimental results.展开更多
In order to achieve the goal of “carbon peak” in 2030 and “carbon neutralization” in 2060, the task of energy conservation has risen to the national strategic level, and its work is urgent. It focuses on energy sa...In order to achieve the goal of “carbon peak” in 2030 and “carbon neutralization” in 2060, the task of energy conservation has risen to the national strategic level, and its work is urgent. It focuses on energy saving and energy consumption in data center, 5G network and other fields. The gravity heat pipe double cycle air conditioning is a kind of room air conditioning which uses natural cooling source with high efficiency. According to the outdoor meteorological parameters of ten typical cities in China, the calculation model of unit hybrid refrigeration mode is established by using integral method. A simplified algorithm for statistical summation is proposed. Then it compares with the same type of refrigerant pump air conditioner, water-cooled chiller and natural cooling plate. The results show that the annual operation time of gravity heat pipe double cycle air conditioner is 50.8% longer than that of refrigerant pump air conditioner. Then the calculation model is verified by the annual actual operation data of a data center in Changsha. The results show that the double cycle air conditioner with gravity heat pipe can save about 34% energy compared with the chiller. The accuracy of the calculation model is 17.5%, which meets the engineering accuracy requirements. The application of gravity heat pipe double cycle air conditioning in hot summer and cold winter area is a scheme worthy of popularization and application.展开更多
基金supported by the Tianjin Education Commission Research Program Project(No.2024KJ105)。
文摘The buoyancy-induced flow constitutes a core scientific issue for thermal management of electronic devices and thermal design of energy systems,where accurate characterization of flow and heat transfer is essential to improve thermal efficiency.In this work,buoyancy-induced flow above two heating elements flush-mounted at the bottom of a square enclosure containing air is numerically investigated over a range of Rayleigh numbers(0<Ra≤1.5×10^(8)),with a focus on equal and unequal heat flux conditions under a constraint of constant total thermal energy input.Distinct flow transitions are observed in both cases,leading to the identification of three flow regimes:Steady,periodic unsteady,and chaotic unsteady.Two types of periodic flows are distinguished,in which the first is a periodic flow dominated by a fundamental frequency(FF)and its integer-multiple frequencies(INTMF),while the second is a more complex periodic flow featuring FF,INTMF,and their sub-harmonics.The transitions between these regimes are affected by the relative heat flux of the two heaters.When the heat flux of the two heaters is unequal,the range of Rayleigh numbers corresponding to periodic flow is suppressed.It is also found that the time-averaged maximum temperature of the strong heater increases more rapidly with Ra,while that of the weak heater increases more slowly,reflecting the interaction between buoyancy-driven flow dynamics and asymmetric heat input.Analysis of the time-averaged Nusselt number demonstrates that heat dissipation from the isothermal walls remains roughly equivalent,even when the heat flux of the two heaters differs by a factor of two.These findings highlight the critical roles of Rayleigh number,the number of heaters,and the heat flux ratio of the heaters in determining heat transfer and flow characteristics for buoyancy-driven convection systems,providing important theoretical support and design references for engineering scenarios such as electronic devices and design of new energy systems.
文摘This study involved numerical simulations of a double tube heat exchanger using the ANSYS FLUENT programversion 22.The study aims to examine methods for minimizing pressure loss and consequently enhancing the thermal performance index(TPI)of a heat exchanger fitted with wavy edge tape that is a heat recovery system(the hot air in simulation instead of t heat from the exhaust gases of the brick factory furnaces and return it to warm the heavy fuel oil by substituting the electrical heater with a heat exchanger to recuperate waste heat from the flue gases,so elevating the temperature of Heavy fuel oil(HFO)to inject from the roof nozzles of combustion chamber of the furnace furthermore reducing cost(by finding the optimal design of wavy edge tape))and energy consumption.Air was selected as the hot gas in the inner pipe instead of furnace exhaust gases due to their similar thermal characteristics.A numerical analysis was conducted to create a novel wavy edge tape with varying widths(50%Di,75%Di,and 95%Di),lengths(1000,1200,1400)mm,amplitudes(5,10,15)mm,and periods of wavy length(5,10,15)mm.The flow rate of the outer pipe fluid(oil)ranges from(0.06 to 0.1)kg/s,while the velocity of the hot fluid(air)varies from(1 to 27)m/s,Re_(air)(6957 to 187,837).The entrance temperature of the hot fluid can be either(200,225,and 250)℃.The study finds that wavy edge tape tubes are more effective than smooth tubes in terms of oil outlet temperature;results revealed that an increase in the oil mass flow rate leads to a decrease in the oil outlet temperature and an increase in the heat transfer rate,at the air temperature 250℃.Additionally,the results indicate that increasing the width,length,and amplitude also leads to an increase in the oil outlet temperature of(94-94.12)℃,the pressure drop of(568.3)Pa,and the Nusselt number(65.7-66.5)respectively on the oil side.Finally,the heat exchanger’s best thermal performance index was found by investigating temperature contour at amplitude(A=5),period(p=15),width(w=75%Di),and length(L=1200 mm).The values for these parameters are,in order(1.02,1.025,1.02,and 1.0077).
文摘Double pipe heat exchangers(DPHEs)are normally utilized in various manufacturing uses owing to their simple design and low maintenance requirements.For that,performance enhancement by improved heat transfer is ongoing.Air injections are a good strategy for enhancing the thermal performance of the DPHE.In the present work,the influence of air bubble injection in a DPHE was experimentally investigated,and the system’s hydrothermal performance improvement parameters were evaluated.Two modes were designed,manufactured,and used to conduct the experiments.The first mode was conducted with no air injection,named a single phase mode,while in the second mode,air was injected into the annulus of DPHE throughout different perforated rings on the side of the annular.Three different ring types were used and coded as R-1,R-2,and R-3,with an added case of insertion of the three rings inside the annulus.The airflow rate was fixed at 1.5 LPM with a 25○C inlet temperature.Also,the hot water rate in the inner pipe was maintained continuously at 3 LPM with a controlled 70○C temperature at the inlet.Five different cold water flow rates,3,3.5,4,4.5,and 5 LPM,in the annulus,were considered with a controlled inlet temperature at 17○C.Additionally,the effectiveness of the heat exchanger,the number of transfer units(NTU),and the overall heat transfer were predicted and considered for performance evaluation and comparison.The outcomes proved that the injection of air and the bubbly flow creation in the heat exchanger’s hot side is an effective method to strengthen the DPHE performance.Moreover,the total heat transfer coefficient was enhanced by 41%in R-1,58.8%in R-2,and 40.1%in R-3 at 4 LPM of cold water.The optimal ring,which yielded the most improvement,was R-2,achieving a 65%improvement in NTU,with a maximum enhancement in effectiveness of 56%.
文摘The dynamic thermal process during double-sided asymmetrical TIG backing welding of large thick plates （ 1 000 mm×700 mm×50 mm） is numerically simulated using MSC. MARC. The effect of arc distance on the thermal cycle in weld zone during double-sided asymmetrical T1G backing welding is investigated. The results show that the workpiece experiences double-peak thermal cycle in double-sided asymmetrical TIG backing welding. On the one hand, the fore arc has the pre- heating effect on the rear pass, and the pre-heating temperature depends on the distance between the double arcs, the heat input of fore arc, and the initial temperature of workpiece. On the other hand, the rear arc has the post-heating effect on the fore pass. The mutual effects of two heat sources decrease with the increase of arc distance.
文摘In present work,a helical double tube heat exchanger is proposed in which an advanced turbulator with blades,semi-conical part,and two holes is inserted in inner section.Two geometrical parameters,including angle of turbulator’s blades(θ) and number of turbulator’s blades(N),are considered.Results indicated that firstly,the best thermal stratification is achieved at θ=180°.Furthermore,at the lowest studied mass flow rate(m = 8 × 10^(-3) kg/s),heat transfer coefficient of turbulator with blade angle of 180° is 130.77%,25%,and 36.36% higher than cases including without turbulator,with turbulator with blade angle of θ =240°,and θ =360°,respectively.Moreover,case with N=12 showed the highest overall performance.At the highest studied mass flow rate(m = 5.842 × 10^(-2) kg/s),heat transfer coefficient for case with N=12 is up to 54.76%,27.45%,and 6.56% higher than cases including without turbulator,with turbulator with N=6,and with turbulator with N=9,respectively.
文摘In order to analyze the maximum power density error with different heat flux distribution parameter values for double ellipsoidal heat source model, a general expression of double ellipsoidal heat source model was derived .front Goldak double ellipsoidal heat source model, and the error of maximum power density was analyzed under this foundation. The calculation error of thermal cycling parameters caused by the maximum power density error was compared quantitatively by numerical simulation. The results show that for guarantee the accuracy of welding numerical simulation, it is better to introduce an error correction coefficient into the Goldak double ellipsoidal heat source model expression. And, heat flux distribution parameter should get higher value for the higher power density welding methods.
文摘A heat exchanger’s performance depends heavily on the operating fluid’s transfer of heat capacity and thermal conductivity.Adding nanoparticles of high thermal conductivity materials is a significant way to enhance the heat transfer fluid’s thermal conductivity.This research used engine oil containing alumina(Al_(2)O_(3))nanoparticles and copper oxide(CuO)to test whether or not the heat exchanger’s efficiency could be improved.To establish the most effective elements for heat transfer enhancement,the heat exchangers thermal performance was tested at 0.05%and 0.1%concentrations for Al_(2)O_(3)and CuO nanoparticles.The simulation results showed that the percentage increase in Nusselt number(Nu)for nanofluid at 0.05%particle concentration compared to pure oil was 9.71%for CuO nanofluids and 6.7%for Al_(2)O_(3)nanofluids.At 0.1%concentration,the enhancement percentage in Nu was approximately 23%for CuO and 18.67%for Al_(2)O_(3)nanofluids,respectively.At a concentration of 0.1%,CuO nanofluid increased the LMTD and overall heat transfer coefficient(U)by 7.24 and 5.91%respectively.Both the overall heat transfer coefficient(U)and the heat transfer coefficient(hn)for CuO nanofluid at a concentration of 0.1%increased by 5.91%and 10.68%,respectively.The effectiveness(εn)of a heat exchanger was increased by roughly 4.09%with the use of CuO nanofluid in comparison to Al_(2)O_(3)at a concentration of 0.1%.The amount of exergy destruction in DTHX goes down as Re and volume fractions go up.Moreover,at 0.05%and 0.1%nanoparticle concentrations,the percentage increase in dimensionless exergy is 10.55%and 13.08%,respectively.Finally,adding the CuO and Al_(2)O_(3)nanoparticles improved the thermal conductivity of the main fluid(oil),resulting in a considerable increase in the thermal performance and rate of heat transfer of a heat exchanger.
文摘Objective: in view of the defects of traditional moxibustion therapeutic apparatus, such as open fire heating is prone to scald and unstable control transmission, a portable moxibustion heating therapeutic apparatus based on Arduino control board for scapulohumeral periarthritis and rotator cuff disease was designed, and its value in the treatment of scapulohumeral periarthritis, rotator cuff disease and rotator cuff injury was evaluated. Methods: ATmega328 single chip microcomputer was used as the control core of the therapeutic instrument, which was composed of DS18B20 temperature sensor, graphene new heating module and low burning point patch made of finished wormwood. Results: the requirements of portable miniaturization were met. The therapeutic effect of Ai Rong was fully released through software program control and dual combined heating. The therapeutic instrument was fully automatic, and the therapeutic efficiency was improved. Conclusion: the therapeutic instrument has obvious overall effect, low cost, and can be used anytime and anywhere in the hospital, which is simple and safe to operate. It is an effective treatment device for shoulder periarthritis, shoulder sleeve disease, shoulder sleeve injury and other common diseases. It has high application value and is worth popularizing.
基金Financial support from the National Natural Science Foundation of China under Grant(22393954)is gratefully acknowledged。
文摘With the energy problem becoming increasingly severe,industrial energy efficiency issues need to be solved urgently.The tube and shell heat exchanger,as the most widely used device for energy recovery and utilisation,its optimal design has become a significantly important research topic.Optimal design solves the tediousness of traditional design and can easily and accurately give the desired design results.Several industrial heat duty targets and pressure drop limitations for the design of shell-and-tube heat exchangers,such as high heat transfer efficiency,large temperature correction coefficient,and high capacity,cannot be met by single-shell units and require series or parallel arrangements.This paper uses Set Trimming to optimize the design of double shell and tube heat exchangers,assuming the possibility of series,parallel,or series-parallel arrangements.Minimum heat transfer area and minimum total annualized cost are used as objective functions to optimize the design of a single or double-shell heat exchanger that better meets the objectives.
文摘Mathematical models of three-dimensional temperature fields in underwater welding with moving heat sources are built. Double ellipsoid Gauss model is proposed as heat sources models. Several factors which affect the temperature fields of underwater welding are analyzed. Water has little influence on thermal efftciency. Water convection coefftcient varies with the temperature difference between the water and the workpiece , and water convection makes molten pool freeze quickly. With the increase of water depth, the dimensions of heat sources model should be reduced as arc shrinks. Finite element technology is used to solve mathematical models. ANSYS software is used as finite element tool, and ANSYS Parametric Design Language is used to develop subprograms for loading the moving heat sources and the various convection coefftcients. Experiment results show that computational results by using double ellipsoid Gauss heat sources model accord well with the experimental results.
文摘In order to achieve the goal of “carbon peak” in 2030 and “carbon neutralization” in 2060, the task of energy conservation has risen to the national strategic level, and its work is urgent. It focuses on energy saving and energy consumption in data center, 5G network and other fields. The gravity heat pipe double cycle air conditioning is a kind of room air conditioning which uses natural cooling source with high efficiency. According to the outdoor meteorological parameters of ten typical cities in China, the calculation model of unit hybrid refrigeration mode is established by using integral method. A simplified algorithm for statistical summation is proposed. Then it compares with the same type of refrigerant pump air conditioner, water-cooled chiller and natural cooling plate. The results show that the annual operation time of gravity heat pipe double cycle air conditioner is 50.8% longer than that of refrigerant pump air conditioner. Then the calculation model is verified by the annual actual operation data of a data center in Changsha. The results show that the double cycle air conditioner with gravity heat pipe can save about 34% energy compared with the chiller. The accuracy of the calculation model is 17.5%, which meets the engineering accuracy requirements. The application of gravity heat pipe double cycle air conditioning in hot summer and cold winter area is a scheme worthy of popularization and application.
