The fatigue life of components can be significantly enhanced by the formation of the surface hardness layer through surface strengthening technology.To avoid the geometric distortion of thin-walled com-ponents caused ...The fatigue life of components can be significantly enhanced by the formation of the surface hardness layer through surface strengthening technology.To avoid the geometric distortion of thin-walled com-ponents caused by strengthening,the strengthening energy is limited and the ideal strengthening effect cannot be obtained.This work aims to propose a novel approach to address this issue effectively.The surface layer with high-density dislocations was obtained by a low-energy surface strengthening method(shot peening)at first.Then the surface strengthening mechanism changes from dislocation strengthen-ing to grain boundary strengthening after electropulsing treatment(EPT).The evolution of residual stress and microstructure was analyzed using multi-scale characterization techniques.The results demonstrate that EPT followed by surface strengthening makes a remarkable 304%increase in fatigue life of TC11 titanium alloy.The enhancement of fatigue life can be attributed to the grain refinement accompanied by the formation of nanotwins and sub-grains in the surface-strengthened layer,as well as the reduction in dislocation density within the substrate after EPT.This study demonstrates the significant potential of EPT in further enhancing the fatigue life of surface pre-strengthened thin-walled components.展开更多
Creep aging is well-known to be a time-dependent,coupled process of deformation and precipitation strengthening for age-hardening alloys.Its existing mechanisms are mainly attributed to those interac-tions between ato...Creep aging is well-known to be a time-dependent,coupled process of deformation and precipitation strengthening for age-hardening alloys.Its existing mechanisms are mainly attributed to those interac-tions between atomic diffusion and dislocation motion.However,an understanding of the relationship between dislocation density and a special multistage creep behavior,i.e.,double steady creep feature,is still far limited.Here we investigate the effect of various dislocation density levels on such an abnormal multistage creep of an Al-Cu-Li alloy.We find that the increased dislocation densities enable an apparent time decrease(from 6.2 h to 0.8 h)of their first steadyⅡ-stage.The yield strength of post-aged sam-ples increases from 425.0 MPa to 580.0 MPa while the corresponding elongation decreases from 12.3%to 7.3%for the creep-aged samples#1 to#4.Microstructural results also reveal that a great difference in dislocation configuration,tailored by various density levels,results in varying creep processes of theⅡ-stage.This stage is closely related to the nucleation and early growth of T_(1)precipitates.Their number densities(maximum:2.9×10^(19)m^(-3))and the average length(maximum:21.3 nm)of T_(1)precipitates are much smaller than those of the stable peak-aged T_(1)phases,suggesting that creepⅡ-stage of all three creep-aged samples is dominant by the nucleation and initial growth of those T_(1)precipitates.This study provides valuable insights into the dislocation density-mediated creep deformation of an Al-Cu-Li alloy.展开更多
Adding numerous dislocations into metallic materials before the forming stage significantly enhances their deformability.However,this beneficial effect of dislocation defects may not have a simple monotonic relationsh...Adding numerous dislocations into metallic materials before the forming stage significantly enhances their deformability.However,this beneficial effect of dislocation defects may not have a simple monotonic relationship with increased dislocation density during electroplastic deformation.This is due to the complex interactions among the drifting electrons,dislocations and solute atoms.This study explores the effect of diverse initial dislocation densities on creep deformation during electrically aided creep aging of an aluminum-lithium alloy.Surprisingly,we discovered a threshold value for the dislocation density that affects electroplastic creep,i.e.,an enhanced effect from dislocations weakens when exceeding this density threshold(an anomalous response to creep).Microstructural data also reveal that such an anomalous response originates mainly from differences in various dislocation density-tailored configurations,which can influence the dislocation motions and precipitation kinetics of the strengthening T1precipitates under the same action of pulsed currents.This study provides important insights into the dislocation density-mediated electroplastic creep of an aluminum-lithium alloy.展开更多
Powder mixture of pure A1 and oxidized SiC was consolidated into 10% （mass fraction） SiCp/AI composites at 523 K by equal channel angular pressing and torsion （ECAP-T）. The interfacial bonding of the composites wa...Powder mixture of pure A1 and oxidized SiC was consolidated into 10% （mass fraction） SiCp/AI composites at 523 K by equal channel angular pressing and torsion （ECAP-T）. The interfacial bonding of the composites was characterized by transmission electron microscopy （TEM） and high resolution transmission electron microscopy （HRTEM）. The selected area electron diffraction （SAED） for the interface was investigated. The elements at the interface were scanned by energy dispersive spectroscopy （EDS） and the EDS mapping was also obtained. X-ray diffraction （XRD） analysis was carried out for the composites fabricated by 1 pass, 2 passes and 4 passes ECAP-T. According to the XRD analysis, the influences of ECAP-T pass on the Bragg angle and interplanar spacing for AI crystalline planes were studied. The results show that after ECAP-T, the interface between A1 and SiC within the composites is a belt of amorphous SiO2 containing a trace of A1, Si and C which diffused from the matrix and the reinforcement. With the growing ECAP-T pass, the Bragg angle decreases and interplanar spacing increases for A1 crystalline planes, due to the accumulated lattice strain. The increasing lattice strain of A1 grains also boosts the density of the dislocation within A1 grains.展开更多
The microstructure evolution of 7A85 aluminum alloy at the conditions of strain rate(0.001−1 s^(−1))and deformation temperature(250−450°C)was studied by optical microscopy(OM)and electron back scattering diffract...The microstructure evolution of 7A85 aluminum alloy at the conditions of strain rate(0.001−1 s^(−1))and deformation temperature(250−450°C)was studied by optical microscopy(OM)and electron back scattering diffraction(EBSD).Based on the K-M dislocation density model,a two-stage K-M dislocation density model of 7A85 aluminum alloy was established.The results reveal that dynamic recovery(DRV)and dynamic recrystallization(DRX)are the main mechanisms of microstructure evolution during thermal deformation of 7A85 aluminum alloy.350−400°C is the transformation zone from dynamic recovery to dynamic recrystallization.At low temperature(≤350°C),DRV is the main mechanism,while DRX mostly occurs at high temperature(≥400°C).At this point,the sensitivity of microstructure evolution to temperature is relatively high.As the temperature increased,the average misorientation angle(θˉ_(c))increased significantly,ranging from 0.93°to 7.13°.Meanwhile,the f_(LAGBs) decreased with the highest decrease of 24%.展开更多
The strength-ductility trade-offdilemma is hard to be evaded in high-strength Mg alloys at sub-zero temperatures,especially in the Mg alloys containing a high volume fraction of precipitates.In this paper,we report an...The strength-ductility trade-offdilemma is hard to be evaded in high-strength Mg alloys at sub-zero temperatures,especially in the Mg alloys containing a high volume fraction of precipitates.In this paper,we report an enhanced strength-ductility synergy at sub-zero temperatures in an aged Mg-7.37Gd-3.1Y-0.27Zr alloy.The tensile stress-strain curves at room temperature(RT),−70℃ and−196℃ show that the strength increases monotonically with decreasing temperature,but the elongation increases first from RT to−70℃ then declines from−70℃ to−196℃.After systematic investigation of the microstructure evolutions at different deformation temperatures via synchrotron X-ray diffraction,electron backscattered diffraction(EBSD)and transmission electron microscopy(TEM),it is found that a high dislocation density with sufficient<c+a>dislocations promotes good tensile ductility at−70℃,which is attributed to the minimized critical resolved shear stress(CRSS)ratio of non-basal<c+a>to basaldislocations.In ad-dition,more shearable precipitates can further improve the ductility via lengthening the mean free path of dislocation glide.The present work demonstrates that an excellent strength-ductility synergy at sub-zero temperatures can be achieved by introducing a high dislocation density and shearable precipitates in high-strength Mg alloys.展开更多
Al–Si–Cu–Mg foundry alloys are used in casting process technologies.However,their strength properties remain low due to their microstructural characteristics and porosity.In this work,the microstructural characteri...Al–Si–Cu–Mg foundry alloys are used in casting process technologies.However,their strength properties remain low due to their microstructural characteristics and porosity.In this work,the microstructural characteristics,dislocation densities,and mechanical properties of Al–Si–Cu–Mg cast alloys prepared through different casting methods were studied experimentally.Four casting processes,namely,gravity casting(GC),rheocasting(RC),thixoforming(Thixo),and Thixo with heat treatment,were used.The GC and RC samples had mainly dendriticα-Al phase microstructures and exhibited coarse Si particles and intermetallic compounds in their interdendritic regions.By contrast,the Thixo and heat-treated Thixo(HT-Thixo)samples exhibited microstructural refinement with uniformly distributedα-Al globules,fine fibrous Si particles,and fragmented intermetallic compounds amongα-Al globules.The accumulation of dislocation densities increased in the Thixo sample as the strain was increased due to plastic deformation.Furthermore,the ultimate tensile strength and yield strength of the HT-Thixo sample increased by 87%and 63%,respectively,relative to those of the GC sample.The cleavage fracture displayed by the GC and RC samples led to brittle failure.Meanwhile,the Thixo and HT-Thixo samples presented dimple-based ductile fracture.展开更多
Understanding the relationship between microstructure features and mechanical properties is of great significance for the improvement and specific adjustment of steel properties.The relationship between mean grain siz...Understanding the relationship between microstructure features and mechanical properties is of great significance for the improvement and specific adjustment of steel properties.The relationship between mean grain size and yield strength is established by the well-known Hall-Petch equation.But due to the complexity of the grain configuration within materials,considering only the mean value is unlikely to give a complete representation of the mechanical behavior.The classical Taylor equation is often used to account for the effect of dislocation density,but not thoroughly tested in combination with grain size influence.In the present study,systematic heat treatment routes and cold rolling followed by annealing are designed for interstitial free(IF)steel to achieve ferritic microstructures that not only vary in mean grain size,but also in grain size distribution and in dislocation density,a combination that is rarely studied in the literature.Optical microscopy is applied to determine the grain size distribution.The dislocation density is determined through XRD measurements.The hardness is analyzed on its relation with the mean grain size,as well as with the grain size distribution and the dislocation density.With the help of the variable selection tool LASSO,it is shown that dislocation density,mean grain size and kurtosis of grain size distribution are the three features which most strongly affect hardness of IF steel.展开更多
The analysis of threading dislocation density （TDD） in Ge-on-Si layer is critical for developing lasers, light emitting diodes （LEDs）, photodetectors （PDs）, modulators, waveguides, metal oxide semiconductor fiel...The analysis of threading dislocation density （TDD） in Ge-on-Si layer is critical for developing lasers, light emitting diodes （LEDs）, photodetectors （PDs）, modulators, waveguides, metal oxide semiconductor field effect transistors （MOSFETs）, and also the integration of Si-based monolithic photonics. The TDD of Ge epitaxial layer is analyzed by etching or transmission electron microscope （TEM）. However, high-resolution x-ray diffraction （HR-XRD） rocking curve provides an optional method to analyze the TDD in Ge layer. The theory model of TDD measurement from rocking curves was first used in zinc-blende semiconductors. In this paper, this method is extended to the case of strained Ge-on-Si layers. The HR-XRD 2θ/ω scan is measured and Ge （004） single crystal rocking curve is utilized to calculate the TDD in strained Ge epitaxial layer. The rocking curve full width at half maximum （FWHM） broadening by incident beam divergence of the instrument, crystal size, and curvature of the crystal specimen is subtracted. The TDDs of samples A and B are calculated to be 1.41108 cm-2 and 6.47108 cm-2, respectively. In addition, we believe the TDDs calculated by this method to be the averaged dislocation density in the Ge epitaxial layer.展开更多
P91 steel is an important bearing material used in nuclear power plants. The study of its mechanical degradation behavior is important for ensuring safe operation. The relationship between the dislocation density of P...P91 steel is an important bearing material used in nuclear power plants. The study of its mechanical degradation behavior is important for ensuring safe operation. The relationship between the dislocation density of P91 steel under different strains and the corresponding nonlinear ultrasonic parameter β was studied. The dislocation density of strained samples was estimated by X-ray diffraction. Nonlinear ultrasonic testing was conducted to evaluate β, showing that this value increased with increasing dislocation density induced by different tensile elongations. It was shown that the ultrasonic secondharmonic generation technique can effectively evaluate the degradation behavior of metallic materials, and the prediction of the residual life of bearing parts in service can be made based on β and the dislocation density.展开更多
In the present work stir casting route is used to fabricate the ZA27 Metal matrix composites containing 3 wt%, 6 wt%, 9 wt%, and 12 wt%. Zircon sand particulates of size 100 mesh. Microstructure studies using Optical ...In the present work stir casting route is used to fabricate the ZA27 Metal matrix composites containing 3 wt%, 6 wt%, 9 wt%, and 12 wt%. Zircon sand particulates of size 100 mesh. Microstructure studies using Optical Microscopy, SEM-EDAX are carried out to ascertain the distribution and morphology of particulates in the composites. Effect of zircon sand as reinforcement on bulk density, porosity, of the fabricated composites is studied. SEM studies are carried out to understand the behavior of as-cast ZA27 alloy reinforced with zircon sand. The dislocation density of the fabricated composite affects the strength of the composites and depends on the strain due to thermal mismatch and is found to increase with increase in weight% of zircon sand. However, it does not consider casting defects of voids/clustering observed in micrographs of the fabricated composite. Porosity in composites does not have influence on Coefficient of thermal expansion (CTE) of the ZA27 composites studied using thermoelastic models like Kerner and turner model and rule of mixtures of composite.展开更多
The creep strain of conventionally treated 2195 alloy is very low,increasing the difficulty of manufacturing Al-Cu-Li alloy sheet parts by creep age forming.Therefore,finding a solution to improve the creep formabilit...The creep strain of conventionally treated 2195 alloy is very low,increasing the difficulty of manufacturing Al-Cu-Li alloy sheet parts by creep age forming.Therefore,finding a solution to improve the creep formability of Al-Cu-Li alloy is vital.A thorough comparison of the effects of cryo-deformation and ambient temperature large pre-deformation(LPD)on the creep ageing response in the 2195 alloy sheet at 160℃with different stresses has been made.The evolution of dislocations and precipitates during creep ageing of LPD alloys are revealed by X-ray diffraction and transmission electron microscopy.High-quality 2195 alloy sheet largely pre-deformed by 80%without edge-cracking is obtained by cryo-rolling at liquid nitrogen temperature,while severe edge-cracking occurs during room temperature rolling.The creep formability and strength of the 2195 alloy are both enhanced by introducing pre-existing dislocations with a density over 1.4×10^(15)m^(−2).At 160℃and 150 MPa,creep strain and creep-aged strength generally increases by 4−6 times and 30−50 MPa in the LPD sample,respectively,compared to conventional T3 alloy counterpart.The elongation of creep-aged LPD sample is low but remains relevant for application.The high-density dislocations,though existing in the form of dislocation tangles,promote the formation of refined T1 precipitates with a uniform dispersion.展开更多
High-quality AlN epitaxial layers with low dislocation densities and uniform crystal quality are essential for next-gener-ation optoelectronic and power devices.This study reports the epitaxial growth of 6-inch AlN fi...High-quality AlN epitaxial layers with low dislocation densities and uniform crystal quality are essential for next-gener-ation optoelectronic and power devices.This study reports the epitaxial growth of 6-inch AlN films on 17 nm AlN/sapphire tem-plates using metal-organic chemical vapor deposition(MOCVD).Comprehensive characterization reveals significant advance-ments in crystal quality and uniformity.Atomic force microscopy(AFM)shows progressive surface roughness reduction during early growth stages,achieving stabilization at a root mean square(RMS)roughness of 0.216 nm within 3 min,confirming suc-cessful 2D growth mode.X-ray rocking curve(XRC)analysis indicates a marked reduction in the(0002)reflection full width at half maximum(FWHM),from 445 to 96 arcsec,evidencing effective dislocation annihilation.Transmission electron microscopy(TEM)demonstrates the elimination of edge dislocations near the AlN template interface.Stress analysis highlights the role of a highly compressive 17 nm AlN template(5.11 GPa)in facilitating threading dislocation bending and annihilation,yielding a final dislocation density of~1.5×10^(7) cm^(-2).Raman spectroscopy and XRC mapping confirm excellent uniformity of stress and crystal quality across the wafer.These findings demonstrate the feasibility of this method for producing high-quality,large-area,atomically flat AlN films,advancing applications in optoelectronics and power electronics.展开更多
Density of dislocations in the near-surface layer was investigated in X-cut LiNbO_(3) depending on thermal annealing in the temperature range of 400℃–600℃.A dynamic model of randomly distributed dislocations has be...Density of dislocations in the near-surface layer was investigated in X-cut LiNbO_(3) depending on thermal annealing in the temperature range of 400℃–600℃.A dynamic model of randomly distributed dislocations has been developed for LiNbO_(3) by using X-ray diffraction.The experimental results showed that the dislocation density of the near-surface layer reached the minimum at the thermal annealing temperature of 500℃,with the analysis being performed when wet selective etching and X-ray diffraction methods were used.We concluded that homogenization annealing is an effective technique to improve the quality of photonic circuits based on LiNbO_(3).The results obtained are important for optical waveguides,LiNbO_(3)-on-insulator-based micro-photonic devices,electro-optical modulators,sensors,etc.展开更多
Fabricating Mg/Al laminate is an effective strategy to circumvent the inherently low formability and poor corrosion resistance of Mg alloys.Here,Mg/Al laminate with good bonding quality and mechanical properties was s...Fabricating Mg/Al laminate is an effective strategy to circumvent the inherently low formability and poor corrosion resistance of Mg alloys.Here,Mg/Al laminate with good bonding quality and mechanical properties was successfully fabricated via porthole die co-extrusion process using ZK60 Mg and TiB_(2)/6061Al composite as constituted layers.Integrating the results from microstructural characterization and mechanical testing,the effects of extrusion temperature on microstructure,interfacial structure,element diffusion,and mechanical properties were investigated.The results show that Mg/Al laminate achieves a sound welding quality by mechanical bonding and diffusion bonding.The obvious intermetallic compounds(βandγ)layer forms at Mg/Al interface,and its thickness increases to 8.3μm as the extrusion temperature reaches 400℃.High extrusion temperature promotes the dynamic recrystallization and grain growth of Mg and Al layers,while the dislocation density decreases.β/γinterface shows a coherent feature,whileγ/Mg interface is semi-coherent with a locally ordered transition zone of 4.5 nm.The rich Mg and Cr layers are found at TiB_(2)/6061 interface,which is conducive to improving the bonding quality.When the extrusion temperature is 370℃,the thickness of diffusion layer is around 5.0μm,and the bonding strength reaches 18.68 MPa,resulting in the best comprehensive mechanical properties.This work provides a new direction for the development of Mg/Al laminate with excellent strength and ductility.展开更多
This study investigates the differences in microstructural control between cryogenic forging combined with pre-deformation(PCF)and traditional thermal forging(TTF)for 7050 aluminum forgings intended for aerospace appl...This study investigates the differences in microstructural control between cryogenic forging combined with pre-deformation(PCF)and traditional thermal forging(TTF)for 7050 aluminum forgings intended for aerospace applications.The PCF process,utilizing cryogenic deformation,significantly refines the coarse grains at the surface of the forgings,resulting in a finer and more uniform microstructure,thereby effectively addressing the issue of surface coarse grains associated with traditional methods.The findings indicate that the PCF process can accumulate higher stored energy,facilitating static recrystallization(SRX)during subsequent heat treatment and enhancing the microstructural uniformity.Utilizing various analytical techniques,including optical microscopy(OM),electron backscatter diffraction(EBSD),and transmission electron microscopy(TEM).This study reveals the superiority of the PCF process in terms of strain accumulation,dislocation density,and grain refinement.In conclusion,this method offers advantages in enhancing the performance and microstructural uniformity of 7050 aluminum forgings,presenting new opportunities for applications in the aluminum forging industry.展开更多
The measurement field of view of the conventional transmission electron microscopy(TEM)nano-moiréand scanning transmission electron microscopy(STEM)nano-moirémethods is limited to the hundred-nanometer scale...The measurement field of view of the conventional transmission electron microscopy(TEM)nano-moiréand scanning transmission electron microscopy(STEM)nano-moirémethods is limited to the hundred-nanometer scale,unable to meet the deformation field measurement requirements of micrometer-scale materials such as transistors and micro-devices.This paper proposed a novel measurement method based on scanning secondary moire,which can realize cross-scale deformation field measurement from nanometers to micrometers and solve the problem of insufficient measurement accuracy when using only the TEM moire method.This method utilized the electron wave in the TEM passing through the atomic lattice of two layers of different materials to generate TEM moire.On this basis,the TEM was tuned to the STEM mode,and by adjusting parameters such as the amount of defocusing,magnification,scanning angle,etc.,the electron beam was focused on the position near the interface of the two layers of materials,and at the same time,the scanning line was made approximately parallel to the direction of one of the TEM moire fringes.The scanning secondary moire patterns were generated when the scanning spacing was close to the TEM moire spacing.Through this method,the deformation field,mechanical properties,and internal defects of crystals can be detected by a large field of view with high sensitivity and high efficiency.Compared to traditional methods,the advantages of scanning secondary moire method lie in significantly improving the measurement field of TEM moire and STEM moire methods,realizing the cross-scale visualization measurement from nanometers to micrometers,and possessing atomic-level displacement measurement sensitivity.It can also simplify and efficiently identify dislocations,offering a new method for large-area visualization observation of dislocation density in broad application prospects.展开更多
The asymmetric creep aging behaviors of a pre-treated Al-Zn-Mg-Cu alloy under high and low stresses have been investigated for high precision creep age forming application of aluminum integral panels.With the increase...The asymmetric creep aging behaviors of a pre-treated Al-Zn-Mg-Cu alloy under high and low stresses have been investigated for high precision creep age forming application of aluminum integral panels.With the increase of applied stress,the creep strains under the tensile stresses are higher than those of compressive stresses and the asymmetry of creep strain is more obvious.However,the mechanical properties of tensile stress creep aged samples are lower than those of compressive stress creep aged samples.Dislocation density,dislocation moving velocity and the proportion of precipitates directly lead to the asymmetry of creep strain and mechanical properties after tensile-compressive creep aging process.In addition,the tensile and compressive stresses have little effect on the width of the precipitate-free zone(PFZ).It indicates that in the high stress creep age forming process of the pretreated Al-Zn-Mg-Cu alloy,the tensile stress promotes the dislocation motion to obtain a better creep strain but weakens its mechanical properties compared with the compressive stress.In the field of civil aviation aircraft component manufacturing,the introduction of tension and compression stress asymmetry into the creep constitutive model may improve the accuracy of creep age forming components.展开更多
To elucidate the mechanisms of regulating the microstructure uniformity in 7050 aluminum forgings through surface cumulative plastic deformation(SCPD),the microstructure under different solution treatments was investi...To elucidate the mechanisms of regulating the microstructure uniformity in 7050 aluminum forgings through surface cumulative plastic deformation(SCPD),the microstructure under different solution treatments was investigated using metallographic observation(OM),electron backscatter diffraction(EBSD),transmission electron microscopy(TEM),and X-ray diffraction(XRD).The findings demonstrate that the most uniform microstructure in the forgings is achieved with a solution treatment at 470℃for 30 min.The SCPD process generates a significant number of needle-shaped precipitates,resulting in a higher dislocation density and stored energy.Solution treatments alleviate the pinning effect of second-phase particles and facilitate static recrystallization(SRX)in forgings,leading to a reduction in grain size.Additionally,mechanical testing results demonstrate 7%−13%increase in tensile strength and more uniform elongation of the forgings in different directions.展开更多
Zn addition to Mg alloys activates non-basal slip or twinning with solute softening effects.On the other hand,the effects of the Zn solute on the macroscopic dislocation behavior and dynamic recrystallization are not ...Zn addition to Mg alloys activates non-basal slip or twinning with solute softening effects.On the other hand,the effects of the Zn solute on the macroscopic dislocation behavior and dynamic recrystallization are not completely understood.Moreover,it is unclear ifslip can be affected by changes in the c/a ratio of solute atoms.This study was conducted to understand the solute strengthening of Zn addition and its effects on the dislocation characteristics and dynamic recrystallization.A hot torsion test was performed on both AM30 and AZ31 alloys up to a high strain to investigate the Zn solute effect on the dislocation characteristics and dynamic recrystallization.The dislocation components of the hot torsioned alloys were evaluated by X-ray line profile analysis and electron backscatter diffraction.The results showed that the Zn solutes slightly accelerate strain accumulation at the initial stages of hot deformation,which accelerated recrystallization at high strain.The dislocation characteristics were changed dynamically by Zn addition:fortified-type slip,dislocation arrangement and strain anisotropy parameters.The most important point was that the dislocation characteristics were changed dramatically at the critical strain for recrystallization and high strain regions.The addition of Zn also acted greatly in these strain areas.This indicates that the rapid formation of-type slip at the serrated grain boundaries occurs at the initiation of dynamic recrystallization and the increase in the grain triple junction because grain refinement has a great influence on the dislocation characteristics at high strain.展开更多
基金supported by the National Nature Science Foun-dation of China(Grant No.50875061).
文摘The fatigue life of components can be significantly enhanced by the formation of the surface hardness layer through surface strengthening technology.To avoid the geometric distortion of thin-walled com-ponents caused by strengthening,the strengthening energy is limited and the ideal strengthening effect cannot be obtained.This work aims to propose a novel approach to address this issue effectively.The surface layer with high-density dislocations was obtained by a low-energy surface strengthening method(shot peening)at first.Then the surface strengthening mechanism changes from dislocation strengthen-ing to grain boundary strengthening after electropulsing treatment(EPT).The evolution of residual stress and microstructure was analyzed using multi-scale characterization techniques.The results demonstrate that EPT followed by surface strengthening makes a remarkable 304%increase in fatigue life of TC11 titanium alloy.The enhancement of fatigue life can be attributed to the grain refinement accompanied by the formation of nanotwins and sub-grains in the surface-strengthened layer,as well as the reduction in dislocation density within the substrate after EPT.This study demonstrates the significant potential of EPT in further enhancing the fatigue life of surface pre-strengthened thin-walled components.
基金supported by the National Natu-ral Science Foundation of China(No.U22A20190)the Science and Technology Innovation Program of Hunan Province(Nos.2020RC4001 and 2022RC1001)+1 种基金Natural Science Foundation of Hu-nan Province(Nos.2022JJ20065 and 2023JJ40739)the National Key R&D Program of China(No.2021YFB3400903).
文摘Creep aging is well-known to be a time-dependent,coupled process of deformation and precipitation strengthening for age-hardening alloys.Its existing mechanisms are mainly attributed to those interac-tions between atomic diffusion and dislocation motion.However,an understanding of the relationship between dislocation density and a special multistage creep behavior,i.e.,double steady creep feature,is still far limited.Here we investigate the effect of various dislocation density levels on such an abnormal multistage creep of an Al-Cu-Li alloy.We find that the increased dislocation densities enable an apparent time decrease(from 6.2 h to 0.8 h)of their first steadyⅡ-stage.The yield strength of post-aged sam-ples increases from 425.0 MPa to 580.0 MPa while the corresponding elongation decreases from 12.3%to 7.3%for the creep-aged samples#1 to#4.Microstructural results also reveal that a great difference in dislocation configuration,tailored by various density levels,results in varying creep processes of theⅡ-stage.This stage is closely related to the nucleation and early growth of T_(1)precipitates.Their number densities(maximum:2.9×10^(19)m^(-3))and the average length(maximum:21.3 nm)of T_(1)precipitates are much smaller than those of the stable peak-aged T_(1)phases,suggesting that creepⅡ-stage of all three creep-aged samples is dominant by the nucleation and initial growth of those T_(1)precipitates.This study provides valuable insights into the dislocation density-mediated creep deformation of an Al-Cu-Li alloy.
基金financially supported by the National Natural Science Foundation of China(Nos.U22A20190 and 52274404)the National Key R&D Program of China(No.2021YFB3400903)。
文摘Adding numerous dislocations into metallic materials before the forming stage significantly enhances their deformability.However,this beneficial effect of dislocation defects may not have a simple monotonic relationship with increased dislocation density during electroplastic deformation.This is due to the complex interactions among the drifting electrons,dislocations and solute atoms.This study explores the effect of diverse initial dislocation densities on creep deformation during electrically aided creep aging of an aluminum-lithium alloy.Surprisingly,we discovered a threshold value for the dislocation density that affects electroplastic creep,i.e.,an enhanced effect from dislocations weakens when exceeding this density threshold(an anomalous response to creep).Microstructural data also reveal that such an anomalous response originates mainly from differences in various dislocation density-tailored configurations,which can influence the dislocation motions and precipitation kinetics of the strengthening T1precipitates under the same action of pulsed currents.This study provides important insights into the dislocation density-mediated electroplastic creep of an aluminum-lithium alloy.
基金Project(51175138) supported by the National Natural Science Foundation of ChinaProjects(2012HGZX0030,2013HGCH0011) supported by the Fundamental Research Funds for the Central Universities,China
文摘Powder mixture of pure A1 and oxidized SiC was consolidated into 10% （mass fraction） SiCp/AI composites at 523 K by equal channel angular pressing and torsion （ECAP-T）. The interfacial bonding of the composites was characterized by transmission electron microscopy （TEM） and high resolution transmission electron microscopy （HRTEM）. The selected area electron diffraction （SAED） for the interface was investigated. The elements at the interface were scanned by energy dispersive spectroscopy （EDS） and the EDS mapping was also obtained. X-ray diffraction （XRD） analysis was carried out for the composites fabricated by 1 pass, 2 passes and 4 passes ECAP-T. According to the XRD analysis, the influences of ECAP-T pass on the Bragg angle and interplanar spacing for AI crystalline planes were studied. The results show that after ECAP-T, the interface between A1 and SiC within the composites is a belt of amorphous SiO2 containing a trace of A1, Si and C which diffused from the matrix and the reinforcement. With the growing ECAP-T pass, the Bragg angle decreases and interplanar spacing increases for A1 crystalline planes, due to the accumulated lattice strain. The increasing lattice strain of A1 grains also boosts the density of the dislocation within A1 grains.
基金Project(51675465)supported by the National Natural Science Foundation of ChinaProject(E2019203075)supported by the Natural Science Foundation of Hebei Province,China+1 种基金Project(BJ2019001)supported by the Top Young Talents Project of the Education Department of Hebei Province,ChinaProject(Kfkt2017-07)supported by the State Key Laboratory Program of High Performance Complex Manufacturing,China。
文摘The microstructure evolution of 7A85 aluminum alloy at the conditions of strain rate(0.001−1 s^(−1))and deformation temperature(250−450°C)was studied by optical microscopy(OM)and electron back scattering diffraction(EBSD).Based on the K-M dislocation density model,a two-stage K-M dislocation density model of 7A85 aluminum alloy was established.The results reveal that dynamic recovery(DRV)and dynamic recrystallization(DRX)are the main mechanisms of microstructure evolution during thermal deformation of 7A85 aluminum alloy.350−400°C is the transformation zone from dynamic recovery to dynamic recrystallization.At low temperature(≤350°C),DRV is the main mechanism,while DRX mostly occurs at high temperature(≥400°C).At this point,the sensitivity of microstructure evolution to temperature is relatively high.As the temperature increased,the average misorientation angle(θˉ_(c))increased significantly,ranging from 0.93°to 7.13°.Meanwhile,the f_(LAGBs) decreased with the highest decrease of 24%.
基金We acknowledge Prof.Jian Wang from the University of Nebraska-Lincoln for insightful discussion.This work is financially supported by the National Key R&D Program of China(No.2021YFB3501005)the Space Utilization System of China Manned Space Engineering(No.KJZ-YY-WCL04)+1 种基金the Natural Science Foundation of Shanghai(No.23ZR1431100)the National Natural Science Foundation of China(No.51825101).Shanghai Syn-chrotron Radiation Facility is acknowledged for supporting the syn-chrotron high energy X-ray diffraction experiments at Beam Line No.BL14B1.
文摘The strength-ductility trade-offdilemma is hard to be evaded in high-strength Mg alloys at sub-zero temperatures,especially in the Mg alloys containing a high volume fraction of precipitates.In this paper,we report an enhanced strength-ductility synergy at sub-zero temperatures in an aged Mg-7.37Gd-3.1Y-0.27Zr alloy.The tensile stress-strain curves at room temperature(RT),−70℃ and−196℃ show that the strength increases monotonically with decreasing temperature,but the elongation increases first from RT to−70℃ then declines from−70℃ to−196℃.After systematic investigation of the microstructure evolutions at different deformation temperatures via synchrotron X-ray diffraction,electron backscattered diffraction(EBSD)and transmission electron microscopy(TEM),it is found that a high dislocation density with sufficient<c+a>dislocations promotes good tensile ductility at−70℃,which is attributed to the minimized critical resolved shear stress(CRSS)ratio of non-basal<c+a>to basaldislocations.In ad-dition,more shearable precipitates can further improve the ductility via lengthening the mean free path of dislocation glide.The present work demonstrates that an excellent strength-ductility synergy at sub-zero temperatures can be achieved by introducing a high dislocation density and shearable precipitates in high-strength Mg alloys.
基金financially supported by the Universiti Kebangsaan Malaysia and the Ministry of Education(MoE)Malaysia(Nos.MI-2019-025 and DIP-2016-007)。
文摘Al–Si–Cu–Mg foundry alloys are used in casting process technologies.However,their strength properties remain low due to their microstructural characteristics and porosity.In this work,the microstructural characteristics,dislocation densities,and mechanical properties of Al–Si–Cu–Mg cast alloys prepared through different casting methods were studied experimentally.Four casting processes,namely,gravity casting(GC),rheocasting(RC),thixoforming(Thixo),and Thixo with heat treatment,were used.The GC and RC samples had mainly dendriticα-Al phase microstructures and exhibited coarse Si particles and intermetallic compounds in their interdendritic regions.By contrast,the Thixo and heat-treated Thixo(HT-Thixo)samples exhibited microstructural refinement with uniformly distributedα-Al globules,fine fibrous Si particles,and fragmented intermetallic compounds amongα-Al globules.The accumulation of dislocation densities increased in the Thixo sample as the strain was increased due to plastic deformation.Furthermore,the ultimate tensile strength and yield strength of the HT-Thixo sample increased by 87%and 63%,respectively,relative to those of the GC sample.The cleavage fracture displayed by the GC and RC samples led to brittle failure.Meanwhile,the Thixo and HT-Thixo samples presented dimple-based ductile fracture.
基金carried out under project number S41.5.14547a in the framework of the Partnership Program of the Materials Innovation Institute M2i(www.m2i.nl)the Technology Foundation TTW(www.stw.nl)which is part of the Netherlands Organization for Scientific Research(www.nwo.nl)。
文摘Understanding the relationship between microstructure features and mechanical properties is of great significance for the improvement and specific adjustment of steel properties.The relationship between mean grain size and yield strength is established by the well-known Hall-Petch equation.But due to the complexity of the grain configuration within materials,considering only the mean value is unlikely to give a complete representation of the mechanical behavior.The classical Taylor equation is often used to account for the effect of dislocation density,but not thoroughly tested in combination with grain size influence.In the present study,systematic heat treatment routes and cold rolling followed by annealing are designed for interstitial free(IF)steel to achieve ferritic microstructures that not only vary in mean grain size,but also in grain size distribution and in dislocation density,a combination that is rarely studied in the literature.Optical microscopy is applied to determine the grain size distribution.The dislocation density is determined through XRD measurements.The hardness is analyzed on its relation with the mean grain size,as well as with the grain size distribution and the dislocation density.With the help of the variable selection tool LASSO,it is shown that dislocation density,mean grain size and kurtosis of grain size distribution are the three features which most strongly affect hardness of IF steel.
基金Project supported by the Research Plan in Shaanxi Province,China(Grant No.2016GY-085)the Opening Project of Key Laboratory of Microelectronic Devices&Integrated Technology,Institute of Microelectronics,Chinese Academy of Sciences(Grant No.90109162905)+1 种基金the Fundamental Research Funds for the Central Universities(Grant No.17-H863-04-ZT-001-019-01)the National Natural Science Foundation of China(Grant Nos.61704130 and 61474085)
文摘The analysis of threading dislocation density （TDD） in Ge-on-Si layer is critical for developing lasers, light emitting diodes （LEDs）, photodetectors （PDs）, modulators, waveguides, metal oxide semiconductor field effect transistors （MOSFETs）, and also the integration of Si-based monolithic photonics. The TDD of Ge epitaxial layer is analyzed by etching or transmission electron microscope （TEM）. However, high-resolution x-ray diffraction （HR-XRD） rocking curve provides an optional method to analyze the TDD in Ge layer. The theory model of TDD measurement from rocking curves was first used in zinc-blende semiconductors. In this paper, this method is extended to the case of strained Ge-on-Si layers. The HR-XRD 2θ/ω scan is measured and Ge （004） single crystal rocking curve is utilized to calculate the TDD in strained Ge epitaxial layer. The rocking curve full width at half maximum （FWHM） broadening by incident beam divergence of the instrument, crystal size, and curvature of the crystal specimen is subtracted. The TDDs of samples A and B are calculated to be 1.41108 cm-2 and 6.47108 cm-2, respectively. In addition, we believe the TDDs calculated by this method to be the averaged dislocation density in the Ge epitaxial layer.
基金Item Sponsored by National Natural Science Foundation of China(61171145,11274226)
文摘P91 steel is an important bearing material used in nuclear power plants. The study of its mechanical degradation behavior is important for ensuring safe operation. The relationship between the dislocation density of P91 steel under different strains and the corresponding nonlinear ultrasonic parameter β was studied. The dislocation density of strained samples was estimated by X-ray diffraction. Nonlinear ultrasonic testing was conducted to evaluate β, showing that this value increased with increasing dislocation density induced by different tensile elongations. It was shown that the ultrasonic secondharmonic generation technique can effectively evaluate the degradation behavior of metallic materials, and the prediction of the residual life of bearing parts in service can be made based on β and the dislocation density.
文摘In the present work stir casting route is used to fabricate the ZA27 Metal matrix composites containing 3 wt%, 6 wt%, 9 wt%, and 12 wt%. Zircon sand particulates of size 100 mesh. Microstructure studies using Optical Microscopy, SEM-EDAX are carried out to ascertain the distribution and morphology of particulates in the composites. Effect of zircon sand as reinforcement on bulk density, porosity, of the fabricated composites is studied. SEM studies are carried out to understand the behavior of as-cast ZA27 alloy reinforced with zircon sand. The dislocation density of the fabricated composite affects the strength of the composites and depends on the strain due to thermal mismatch and is found to increase with increase in weight% of zircon sand. However, it does not consider casting defects of voids/clustering observed in micrographs of the fabricated composite. Porosity in composites does not have influence on Coefficient of thermal expansion (CTE) of the ZA27 composites studied using thermoelastic models like Kerner and turner model and rule of mixtures of composite.
基金Projects(52274404,52305441,U22A20190)supported by the National Natural Science Foundation of ChinaProjects(2022JJ20065,2023JJ40739)supported by the Natural Science Foundation of Hunan Province,China+2 种基金Project(2022RC1001)supported by the Science and Technology Innovation Program of Hunan Province,ChinaProject(2023ZZTS0972)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(2021YFB3400903)supported by the National Key R&D Program of China。
文摘The creep strain of conventionally treated 2195 alloy is very low,increasing the difficulty of manufacturing Al-Cu-Li alloy sheet parts by creep age forming.Therefore,finding a solution to improve the creep formability of Al-Cu-Li alloy is vital.A thorough comparison of the effects of cryo-deformation and ambient temperature large pre-deformation(LPD)on the creep ageing response in the 2195 alloy sheet at 160℃with different stresses has been made.The evolution of dislocations and precipitates during creep ageing of LPD alloys are revealed by X-ray diffraction and transmission electron microscopy.High-quality 2195 alloy sheet largely pre-deformed by 80%without edge-cracking is obtained by cryo-rolling at liquid nitrogen temperature,while severe edge-cracking occurs during room temperature rolling.The creep formability and strength of the 2195 alloy are both enhanced by introducing pre-existing dislocations with a density over 1.4×10^(15)m^(−2).At 160℃and 150 MPa,creep strain and creep-aged strength generally increases by 4−6 times and 30−50 MPa in the LPD sample,respectively,compared to conventional T3 alloy counterpart.The elongation of creep-aged LPD sample is low but remains relevant for application.The high-density dislocations,though existing in the form of dislocation tangles,promote the formation of refined T1 precipitates with a uniform dispersion.
基金supported by National Key R&D Program of China(2022YFB3605100)the National Science Fund for Distinguished Young Scholars of China(62425408)+5 种基金the National Natural Science Foundation of China(62204241,U22A2084,and 62121005)Key Research and Development Projects of Jilin Provincial Science and Technology Development Plan(20240302027GX)the Natural Science Foundation of Jilin Province(20230101345JC,20230101360JC,20230101107JC)the Youth Innovation Promotion Association of CAS(2023223)the Young Elite Scientist Sponsorship Program By CAST(YESS20200182)the CAS Talents Program.
文摘High-quality AlN epitaxial layers with low dislocation densities and uniform crystal quality are essential for next-gener-ation optoelectronic and power devices.This study reports the epitaxial growth of 6-inch AlN films on 17 nm AlN/sapphire tem-plates using metal-organic chemical vapor deposition(MOCVD).Comprehensive characterization reveals significant advance-ments in crystal quality and uniformity.Atomic force microscopy(AFM)shows progressive surface roughness reduction during early growth stages,achieving stabilization at a root mean square(RMS)roughness of 0.216 nm within 3 min,confirming suc-cessful 2D growth mode.X-ray rocking curve(XRC)analysis indicates a marked reduction in the(0002)reflection full width at half maximum(FWHM),from 445 to 96 arcsec,evidencing effective dislocation annihilation.Transmission electron microscopy(TEM)demonstrates the elimination of edge dislocations near the AlN template interface.Stress analysis highlights the role of a highly compressive 17 nm AlN template(5.11 GPa)in facilitating threading dislocation bending and annihilation,yielding a final dislocation density of~1.5×10^(7) cm^(-2).Raman spectroscopy and XRC mapping confirm excellent uniformity of stress and crystal quality across the wafer.These findings demonstrate the feasibility of this method for producing high-quality,large-area,atomically flat AlN films,advancing applications in optoelectronics and power electronics.
文摘Density of dislocations in the near-surface layer was investigated in X-cut LiNbO_(3) depending on thermal annealing in the temperature range of 400℃–600℃.A dynamic model of randomly distributed dislocations has been developed for LiNbO_(3) by using X-ray diffraction.The experimental results showed that the dislocation density of the near-surface layer reached the minimum at the thermal annealing temperature of 500℃,with the analysis being performed when wet selective etching and X-ray diffraction methods were used.We concluded that homogenization annealing is an effective technique to improve the quality of photonic circuits based on LiNbO_(3).The results obtained are important for optical waveguides,LiNbO_(3)-on-insulator-based micro-photonic devices,electro-optical modulators,sensors,etc.
基金supports from the National Natural Science Foundation of China(52175338 and 52222510)Science Fund for Distinguished Young Scholars of Shandong Province(ZR2021JQ21)Key Research and Development Program of Shandong Province(2021ZLGX01).
文摘Fabricating Mg/Al laminate is an effective strategy to circumvent the inherently low formability and poor corrosion resistance of Mg alloys.Here,Mg/Al laminate with good bonding quality and mechanical properties was successfully fabricated via porthole die co-extrusion process using ZK60 Mg and TiB_(2)/6061Al composite as constituted layers.Integrating the results from microstructural characterization and mechanical testing,the effects of extrusion temperature on microstructure,interfacial structure,element diffusion,and mechanical properties were investigated.The results show that Mg/Al laminate achieves a sound welding quality by mechanical bonding and diffusion bonding.The obvious intermetallic compounds(βandγ)layer forms at Mg/Al interface,and its thickness increases to 8.3μm as the extrusion temperature reaches 400℃.High extrusion temperature promotes the dynamic recrystallization and grain growth of Mg and Al layers,while the dislocation density decreases.β/γinterface shows a coherent feature,whileγ/Mg interface is semi-coherent with a locally ordered transition zone of 4.5 nm.The rich Mg and Cr layers are found at TiB_(2)/6061 interface,which is conducive to improving the bonding quality.When the extrusion temperature is 370℃,the thickness of diffusion layer is around 5.0μm,and the bonding strength reaches 18.68 MPa,resulting in the best comprehensive mechanical properties.This work provides a new direction for the development of Mg/Al laminate with excellent strength and ductility.
基金Project(2021GK1040) supported by the Major Projects of Scientific and Technology Innovation of Hunan Province,ChinaProjects(52375398,52171018) supported by the National Natural Science Foundation of China+1 种基金Project(Kfkt2023-09) supported by the Open Research Fund of State Key Laboratory of Precision Manufacturing for Extreme Service Performance,Central South University,ChinaProject(E2021203059) supported by the Natural Science Foundation of Hebei Province,China。
文摘This study investigates the differences in microstructural control between cryogenic forging combined with pre-deformation(PCF)and traditional thermal forging(TTF)for 7050 aluminum forgings intended for aerospace applications.The PCF process,utilizing cryogenic deformation,significantly refines the coarse grains at the surface of the forgings,resulting in a finer and more uniform microstructure,thereby effectively addressing the issue of surface coarse grains associated with traditional methods.The findings indicate that the PCF process can accumulate higher stored energy,facilitating static recrystallization(SRX)during subsequent heat treatment and enhancing the microstructural uniformity.Utilizing various analytical techniques,including optical microscopy(OM),electron backscatter diffraction(EBSD),and transmission electron microscopy(TEM).This study reveals the superiority of the PCF process in terms of strain accumulation,dislocation density,and grain refinement.In conclusion,this method offers advantages in enhancing the performance and microstructural uniformity of 7050 aluminum forgings,presenting new opportunities for applications in the aluminum forging industry.
基金supported by the National Natural Science Foundation of China(Grant Nos.12372178 and 12327801).
文摘The measurement field of view of the conventional transmission electron microscopy(TEM)nano-moiréand scanning transmission electron microscopy(STEM)nano-moirémethods is limited to the hundred-nanometer scale,unable to meet the deformation field measurement requirements of micrometer-scale materials such as transistors and micro-devices.This paper proposed a novel measurement method based on scanning secondary moire,which can realize cross-scale deformation field measurement from nanometers to micrometers and solve the problem of insufficient measurement accuracy when using only the TEM moire method.This method utilized the electron wave in the TEM passing through the atomic lattice of two layers of different materials to generate TEM moire.On this basis,the TEM was tuned to the STEM mode,and by adjusting parameters such as the amount of defocusing,magnification,scanning angle,etc.,the electron beam was focused on the position near the interface of the two layers of materials,and at the same time,the scanning line was made approximately parallel to the direction of one of the TEM moire fringes.The scanning secondary moire patterns were generated when the scanning spacing was close to the TEM moire spacing.Through this method,the deformation field,mechanical properties,and internal defects of crystals can be detected by a large field of view with high sensitivity and high efficiency.Compared to traditional methods,the advantages of scanning secondary moire method lie in significantly improving the measurement field of TEM moire and STEM moire methods,realizing the cross-scale visualization measurement from nanometers to micrometers,and possessing atomic-level displacement measurement sensitivity.It can also simplify and efficiently identify dislocations,offering a new method for large-area visualization observation of dislocation density in broad application prospects.
基金Project(2021YFB3400900)supported by the National Key R&D Program of ChinaProjects(51905551,52205435)supported by the National Natural Science Foundation of China Youth Foundation+1 种基金Project(2022ZZTS0196)supported by the Fundamental Research Founds for the Central Universities,ChinaProject(CX20220282)supported by the Hunan Provincial Innovation Foundation for Postgraduate,China。
文摘The asymmetric creep aging behaviors of a pre-treated Al-Zn-Mg-Cu alloy under high and low stresses have been investigated for high precision creep age forming application of aluminum integral panels.With the increase of applied stress,the creep strains under the tensile stresses are higher than those of compressive stresses and the asymmetry of creep strain is more obvious.However,the mechanical properties of tensile stress creep aged samples are lower than those of compressive stress creep aged samples.Dislocation density,dislocation moving velocity and the proportion of precipitates directly lead to the asymmetry of creep strain and mechanical properties after tensile-compressive creep aging process.In addition,the tensile and compressive stresses have little effect on the width of the precipitate-free zone(PFZ).It indicates that in the high stress creep age forming process of the pretreated Al-Zn-Mg-Cu alloy,the tensile stress promotes the dislocation motion to obtain a better creep strain but weakens its mechanical properties compared with the compressive stress.In the field of civil aviation aircraft component manufacturing,the introduction of tension and compression stress asymmetry into the creep constitutive model may improve the accuracy of creep age forming components.
基金supported by the Natural Science Foundation of Hebei Province,China(Nos.E2019203075,E2021203059)the National Natural Science Foundation of China(No.52171018)+1 种基金Top Young Talents Project of the Education Department of Hebei Province,China(No.BJ2019001)the Open Research Fund of State Key Laboratory of Precision Manufacturing for Extreme Service Performance,Central South University,China(No.Kfkt2023-09).
文摘To elucidate the mechanisms of regulating the microstructure uniformity in 7050 aluminum forgings through surface cumulative plastic deformation(SCPD),the microstructure under different solution treatments was investigated using metallographic observation(OM),electron backscatter diffraction(EBSD),transmission electron microscopy(TEM),and X-ray diffraction(XRD).The findings demonstrate that the most uniform microstructure in the forgings is achieved with a solution treatment at 470℃for 30 min.The SCPD process generates a significant number of needle-shaped precipitates,resulting in a higher dislocation density and stored energy.Solution treatments alleviate the pinning effect of second-phase particles and facilitate static recrystallization(SRX)in forgings,leading to a reduction in grain size.Additionally,mechanical testing results demonstrate 7%−13%increase in tensile strength and more uniform elongation of the forgings in different directions.
基金supported by the Inha University Research Grants。
文摘Zn addition to Mg alloys activates non-basal slip or twinning with solute softening effects.On the other hand,the effects of the Zn solute on the macroscopic dislocation behavior and dynamic recrystallization are not completely understood.Moreover,it is unclear ifslip can be affected by changes in the c/a ratio of solute atoms.This study was conducted to understand the solute strengthening of Zn addition and its effects on the dislocation characteristics and dynamic recrystallization.A hot torsion test was performed on both AM30 and AZ31 alloys up to a high strain to investigate the Zn solute effect on the dislocation characteristics and dynamic recrystallization.The dislocation components of the hot torsioned alloys were evaluated by X-ray line profile analysis and electron backscatter diffraction.The results showed that the Zn solutes slightly accelerate strain accumulation at the initial stages of hot deformation,which accelerated recrystallization at high strain.The dislocation characteristics were changed dynamically by Zn addition:fortified-type slip,dislocation arrangement and strain anisotropy parameters.The most important point was that the dislocation characteristics were changed dramatically at the critical strain for recrystallization and high strain regions.The addition of Zn also acted greatly in these strain areas.This indicates that the rapid formation of-type slip at the serrated grain boundaries occurs at the initiation of dynamic recrystallization and the increase in the grain triple junction because grain refinement has a great influence on the dislocation characteristics at high strain.
