To analyze the differences in the transport and distribution of different types of proppants and to address issues such as the short effective support of proppant and poor placement in hydraulically intersecting fract...To analyze the differences in the transport and distribution of different types of proppants and to address issues such as the short effective support of proppant and poor placement in hydraulically intersecting fractures,this study considered the combined impact of geological-engineering factors on conductivity.Using reservoir production parameters and the discrete elementmethod,multispherical proppants were constructed.Additionally,a 3D fracture model,based on the specified conditions of the L block,employed coupled(Computational Fluid Dynamics)CFD-DEM(Discrete ElementMethod)for joint simulations to quantitatively analyze the transport and placement patterns of multispherical proppants in intersecting fractures.Results indicate that turbulent kinetic energy is an intrinsic factor affecting proppant transport.Moreover,the efficiency of placement and migration distance of low-sphericity quartz sand constructed by the DEM in the main fracture are significantly reduced compared to spherical ceramic proppants,with a 27.7%decrease in the volume fraction of the fracture surface,subsequently affecting the placement concentration and damaging fracture conductivity.Compared to small-angle fractures,controlling artificial and natural fractures to expand at angles of 45°to 60°increases the effective support length by approximately 20.6%.During hydraulic fracturing of gas wells,ensuring the fracture support area and post-closure conductivity can be achieved by controlling the sphericity of proppants and adjusting the perforation direction to control the direction of artificial fractures.展开更多
Nonuniform track support and differential settlements are commonly observed in bridge approaches where the ballast layer can develop gaps at crosstie-ballast interfaces often referred to as a hanging crosstie conditio...Nonuniform track support and differential settlements are commonly observed in bridge approaches where the ballast layer can develop gaps at crosstie-ballast interfaces often referred to as a hanging crosstie condition.Hanging crossties usually yield unfavorable dynamic effects such as higher wheel loads,which negatively impact the serviceability and safety of railway operations.Hence,a better understanding of the mechanisms that cause hanging crossties and their effects on the ballast layer load-deformation characteristics is necessary.Since the ballast layer is a particulate medium,the discrete element method(DEM),which simulates ballast particle interactions individually,is ideal to explore the interparticle contact forces and ballast movements under dynamic wheel loading.Accurate representations of the dynamic loads from the train and track superstructure are needed for high-fidelity DEM modeling.This paper introduces an integrated modeling approach,which couples a single-crosstie DEM ballast model with a train–track–bridge(TTB)model using a proportional–integral–derivative control loop.The TTB–DEM model was validated with field measurements,and the coupled model calculates similar crosstie displacements as the TTB model.The TTB–DEM provided new insights into the ballast particle-scale behavior,which the TTB model alone cannot explore.The TTB–DEM coupling approach identified detrimental effects of hanging crossties on adjacent crossties,which were found to experience drastic vibrations and large ballast contact force concentrations.展开更多
Hydraulic fracturing,an effective method for enhancing coal seam productivity,largely determines coalbed methane(CBM)production,which is significantly influenced by geological and engineering factors.This study focuse...Hydraulic fracturing,an effective method for enhancing coal seam productivity,largely determines coalbed methane(CBM)production,which is significantly influenced by geological and engineering factors.This study focuses on the L block to investigate the mechanisms influencing efficient fracture propagation and enhanced stimulated reservoir volume(SRV)in fracturing.To explore the mechanisms influencing effective fracture propagation and enhanced SRV,the L block was selected as the research object,with a comprehensive consideration of geological background,reservoir properties,and dynamic production data.By combining the discrete lattice method with numer-ical analysis and true triaxial experimental simulation,the fracture morphology of a single cluster and the propagation patterns of multiple clusters of complex fractures were obtained.Additionally,the optimization of temporary plugging timing and the fracture map under multiple factors were innovatively proposed.Results indicate that greater flow rate and viscosity can effectively overcome the stress shadow effect of the outermost fractures(1st and 6th clusters),increasing the fracture pressure of the single cluster and the equilibrium degree of multiple fracture propagation,thus forming a more complex fracture network.Moreover,when viscosity exceeds 45 pressure concentrates at fracture mPa⋅s,tips,promoting discontinuous propagation and reducing flow resistance.Conversely,increased gangue thickness and spacing between horizontal wells increase the vertical propagation pressure,suppressing fracture growth and reducing central flow velocity.This study provides a multi-cluster fracture propagation map for optimizing volumetric fracturing in coal seams and suggests that the optimal temporary plugging time significantly enhances the SRV.展开更多
Deepwater drilling riser is the key equipment connecting the subsea wellhead and floating drilling platform.Due to complex marine environment,vortex-induced vibration(ViV)will be generated on riser,which will induce f...Deepwater drilling riser is the key equipment connecting the subsea wellhead and floating drilling platform.Due to complex marine environment,vortex-induced vibration(ViV)will be generated on riser,which will induce fatigue failure and even cause unpredictable drilling accidents.Therefore,it is important to study the ViV characteristics of deepwater drilling riser and reveal the main controlling factors for ensuring the safe and efficient operation of deepwater drilling engineering.In this paper,the ViV of deepwater drilling riser is numerically simulated in time domain based on the discrete vortex method(DvM).A hydrodynamic analysis model and governing equation of VIV is proposed with considering the effect of riser motion using DVM and slice method,where the governing equation is solved by Runge-Kutta method.Model validation is performed,which verified the correctness and accuracy of the mechanical model and the solution method.On this basis,the influence of the number of control points,current velocity,riser outer diameter,shear flow and top tension on the ViV characteristics of deepwater drilling risers are discussed in detail.The results show that with the increase of current velocity,the vibration amplitude of deepwater drilling riser decreases obviously,while the vibration frequency increases gradually.However,if the outer diameter of riser increases,the vibration amplitude increases,while the vibration frequency decreases gradually.The top tension also has great influence on the VIV of riser.When the top tension is 1.25 G,the VIV is suppressed to a certain extent.This study has guiding significance for optimal design and engineering control of deepwater drilling riser.展开更多
The homogeneity of aggregate blend has a significant influence on the performance of asphalt mixture.The composition of aggregate blend,including the size combination and the mass ratio between each size particles(MRE...The homogeneity of aggregate blend has a significant influence on the performance of asphalt mixture.The composition of aggregate blend,including the size combination and the mass ratio between each size particles(MRESP),is an important factor affecting the homogeneity.This study investigated the influence of the size combination and MRESP on the distribution homogeneity of particles in aggregate blend using discrete element method(DEM).An indicator quantifying the distribution homogeneity was established according to the coefficient of variation(CV)for particle number.Two-size,three-size,and four-size aggregate blends with various compositions were designed.Laboratory tests show the DEM simulation is feasible.The particle distribution homogeneity in various blends was analyzed.The results showed the distribution homogeneity of each size particles in a blend is closely related to their mass fraction.The higher the mass fraction of the particles,the more homogeneous the distribution of them.The MRESP has no significant influence on the homogeneity of the blend composed of only coarse aggregates.However,the homogeneity of the blend composed of coarse and fine aggregates improves gradually with the increase of the mass fraction of fine aggregates.The smaller the maximum particle size in a blend,the better the homogeneity.It is suggested that the mass fraction of fine aggregates should be between 33%and 50%for achieving good homogeneity of aggregate blends.The research results can provide a reference for gradation design of asphalt mixture.展开更多
Steep bedding slopes are widely distributed in Southwestern China’s mountainous regions and have complex seismic responses and instability risks,causing casualties and property losses.Considering the high-seismic-int...Steep bedding slopes are widely distributed in Southwestern China’s mountainous regions and have complex seismic responses and instability risks,causing casualties and property losses.Considering the high-seismic-intensity environment,the dynamic failure evolution and instability mechanism of high-steep bedding slopes are simulated via the discrete element method and shaking table test.The dynamic response characteristics and cumulative failure effects of slopes subjected to continuous ground motion are investigated.The results show that the dynamic response characteristics of slopes under continuous earthquakes are influenced by geological and topographic conditions.Elevation has a distinct impact on both the slope interior and surface,with amplification effects more pronounced on the surface.The weak interlayers have different influences on the dynamic amplification effect of slopes.Weak interlayers have dynamic magnification effects on the slope surface at relative elevations of 0-0.33 and 0.82-1.0 but have weakening effects between 0.33 and 0.82.Moreover,the weak interlayers also have controlling effects on the dynamic instability mode of slopes.The characteristics of intergranular contact failure,fracture propagation,and displacement distribution are analyzed to reveal the dynamic failure evolution and instability mechanism through the discrete-element model.The dynamic instability process of slopes includes three stages:fracture initiation(0-0.2g),fracture expansion(0.2g-0.3g),and sliding instability(0.3g-0.6g).This work can provide a valuable reference for the seismic stability and reinforcement of complex slopes.展开更多
The Richtmyer–Meshkov(RM)instability plays an important role in various natural and engineering fields such as inertial confinement fusion.In this study,the effect of relaxation time on the RM instability under resho...The Richtmyer–Meshkov(RM)instability plays an important role in various natural and engineering fields such as inertial confinement fusion.In this study,the effect of relaxation time on the RM instability under reshock impact is investigated using a two-component discrete Boltzmann method.The hydrodynamic and thermodynamic characteristics of the fluid system are comprehensively analyzed from the perspectives of the density gradient,vorticity,kinetic energy,mixing degree,mixing width and non-equilibrium intensity.Simulation results indicate that for longer relaxation time,the diffusion and dissipation are enhanced,the physical gradients decrease,and the growth of the interface is suppressed.Furthermore,the non-equilibrium manifestations show complex patterns,driven by the competitive physical mechanisms of the diffusion,dissipation,shock wave,rarefaction wave,transverse wave and fluid instabilities.These findings provide valuable insight into the fundamental mechanism of compressible fluid flows.展开更多
The glutenite reservoir is strongly heterogeneous due to the random distribution of gravels, making it challenging to perform hydraulic fracturing effectively. To solve this issue, it is essential to study interaction...The glutenite reservoir is strongly heterogeneous due to the random distribution of gravels, making it challenging to perform hydraulic fracturing effectively. To solve this issue, it is essential to study interaction behavior between hydraulic fractures(HFs) and gravels. A coupled hydro-mechanical model is proposed for HF propagation in glutenite using a grain-based discrete element method. This paper first investigates the dynamic evolution of HFs in glutenite, then analyzes the influences of various factors such as horizontal stress difference(Δσ), minimum horizontal stress(σh), gravel content(Vg), gravel size(dg), and stiffness ratio of gravel to matrix(Rs) on HF propagation geometries. Results show that penetrating the gravel is the primary HF-gravel interaction behavior, which follows sequential and staggered initiation modes. Bypassing the gravel is the secondary behavior, which obeys the sequential initiation mode and occurs when the orientation of the gravel boundary is inclined to the maximum horizontal stress(σH). An offset along the gravel boundary is usually formed while penetrating gravels, and the offsets may cause fracture widths to decrease by 37.8%-84.4%. Even if stress dominates the direction of HF propagation, HFs still tend to deflect within gravels. The deviation angle from σH decreases with rising Δσand increases with the increase of dgand Rs. Additionally, intra-gravel shear HFs(IGS-HFs) are prone to be generated in coarse-grained glutenite under high Δσ, while more gravel-bypassing shear HFs(GBSHFs) tend to be created in argillaceous glutenite with high Rsthan in sandy glutenite with low Rs. The findings above prompt the emergence of a novel HF propagation pattern in glutenite, which helps to understand the real HF geometries and to provide theoretical guidance for treatments in the field.展开更多
Ceramic spheres,typically with a particle diameter of less than 0.8 mm,are frequently utilized as a critical proppant material in hydraulic fracturing for petroleum and natural gas extraction.Porous ceramic spheres wi...Ceramic spheres,typically with a particle diameter of less than 0.8 mm,are frequently utilized as a critical proppant material in hydraulic fracturing for petroleum and natural gas extraction.Porous ceramic spheres with artificial inherent pores are an important type of lightweight proppant,enabling their transport to distant fracture extremities and enhancing fracture conductivity.However,the focus frequently gravitates towards the low-density advantage,often overlooking the pore geometry impacts on compressive strength by traditional strength evaluation.This paper numerically bypasses such limitations by using a combined finite and discrete element method(FDEM)considering experimental results.The mesh size of the model undergoes validation,followed by the calibration of cohesive element parameters via the single particle compression test.The stimulation elucidates that proppants with a smaller pore size(40μm)manifest crack propagation evolution at a more rapid pace in comparison to their larger-pore counterparts,though the influence of pore diameter on overall strength is subtle.The inception of pores not only alters the trajectory of crack progression but also,with an increase in porosity,leads to a discernible decline in proppant compressive strength.Intriguingly,upon crossing a porosity threshold of 10%,the decrement in strength becomes more gradual.A denser congregation of pores accelerates crack propagation,undermining proppant robustness,suggesting that under analogous conditions,hollow proppants might not match the strength of their porous counterparts.This exploration elucidates the underlying mechanisms of proppant failure from a microstructural perspective,furnishing pivotal insights that may guide future refinements in the architectural design of porous proppant.展开更多
Hydraulic fracturing technology has played an important role in the exploitation of unconventional oil and gas resources,however,its application to gas hydrate reservoirs has been rarely studied.Currently,there is sti...Hydraulic fracturing technology has played an important role in the exploitation of unconventional oil and gas resources,however,its application to gas hydrate reservoirs has been rarely studied.Currently,there is still limited understanding of the propagation and extension of fractures around the wellbore during the fracturing process of horizontal wells in hydrate reservoirs,as well as the stress interference patterns between fractures.This study simulates hydraulic fracturing processes in hydrate reservoirs using a fluidsolid coupling discrete element method(DEM),and analyzes the impacts of hydrate saturation and geological and engineering factors on fracture extension and stress disturbance.The results show that hydraulic fracturing is more effective when hydrate saturation exceeds 30%and that fracture pressure increases with saturation.The increase in horizontal stress differential enhances the directionality of fracture propagation and reduces stress disturbance.The distribution uniformity index(DUI)reveals that injection pressure is directly proportional to the number of main fractures and inversely proportional to fracturing time,with fracturing efficiency depending on the spacing between injection points and the distance between wells.This work may provide reference for the commercial exploitation of natural gas hydrates.展开更多
Gas storage in abandoned mines is one way to reuse waste space resources.The surrounding rock of gas storage reservoirs in underground roadways undergoes damage and deformation under the cyclic loading of gas charging...Gas storage in abandoned mines is one way to reuse waste space resources.The surrounding rock of gas storage reservoirs in underground roadways undergoes damage and deformation under the cyclic loading of gas charging and discharging,which can pose a risk to the safety of the reservoirs.This study establishes a true triaxial numerical model of rock mass with the discrete element method(DEM)and explores the crack evolution of surrounding rock of underground gas storage during cyclic loading and unloading.Also,a damage evolution model in numerical analysis considering residual deformation is developed to explain the experimental results.As was revealed,cyclic loading and unloading resulted in fatigue damage in the specimen and caused strength deterioration of the specimen.During the loading process,the uniformly distributed force chains of the rock mass redistributed,evolving gradually to mostly transverse force chains.This contributed to the appearance of blank areas in the force chains when through cracks appear.The ratio of tensile cracks to shear cracks gradually decreases and finally stabilizes at 7:1.The damage evolution model considering residual strain can be mutually verified with the numerical simulation results.Based on the DEM model,it was found that there was a certain threshold of confining pressure.When the confining pressure exceeded 30 MPa,the deformation to ductility of sandstone samples began to accelerate,with a greater residual strength.This study provides a theoretical basis for analyzing the long-term mechanical behavior of surrounding rock of gas storage in abandoned mines.展开更多
In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method （DEM）. A digital specimen g...In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method （DEM）. A digital specimen generation procedure considering aggregate gradation and irregular shape is developed based on the probability theory and the Monte Carlo method. The virtual rutting test is then conducted based on the generated digital specimen. In addition, on the basis of the time-temperature superposition （TTS） principle, a calculation method is used to reduce the computation time of the virtual rutting test. The simulation results are compared with the laboratory measurements. The results show that the calculation method based on the TFS principle in the discrete element （DE） viscoelastic model can significantly reduce the computation time. The deformation law of asphalt mixtures in the virtual rutting test is similar to the laboratory measurements, and the deformation and the dynamic stability of the virtual rutting test are slightly greater than the laboratory measurements. The two-dimensional virtual rutting test can predict the permanent deformation performance of asphalt mixtures.展开更多
We conducted a study on the numerical calculation and response analysis of a transient electromagnetic field generated by a ground source in geological media. One solution method, the traditional discrete image method...We conducted a study on the numerical calculation and response analysis of a transient electromagnetic field generated by a ground source in geological media. One solution method, the traditional discrete image method, involves complex operation, and its digital filtering algorithm requires a large number of calculations. To solve these problems, we proposed an improved discrete image method, where the following are realized： the real number of the electromagnetic field solution based on the Gaver-Stehfest algorithm for approximate inversion, the exponential approximation of the objective kernel function using the Prony method, the transient electromagnetic field according to discrete image theory, and closed-form solution of the approximate coefficients. To verify the method, we tentatively calculated the transient electromagnetic field in a homogeneous model and compared it with the results obtained from the Hankel transform digital filtering method. The results show that the method has considerable accuracy and good applicability. We then used this method to calculate the transient electromagnetic field generated by a ground magnetic dipole source in a typical geoelectric model and analyzed the horizontal component response of the induced magnetic field obtained from the ＂ground excitation-stratum measurement method. We reached the conclusion that the horizontal component response of a transient field is related to the geoelectric structure, observation time, spatial location, and others. The horizontal component response of the induced magnetic field reflects the eddy current field distribution and its vertical gradient variation. During the detection of abnormal objects, positions with a zero or comparatively large offset were selected for the drill- hole measurements or a comparatively long observation delay was adopted to reduce the influence of the ambient field on the survey results. The discrete image method and forward calculation results in this paper can be used as references for relevant research.展开更多
COREX process is one of the earliest industrialized smelting reduction ironmaking technology.A numerical simulation model based on discrete element method ( DEM ) has been developed to analyze the burden distribution ...COREX process is one of the earliest industrialized smelting reduction ironmaking technology.A numerical simulation model based on discrete element method ( DEM ) has been developed to analyze the burden distribution in the melter gasifier of COREX process.The DEM considering the collisions between particles can directly reproduce the charging process.The burden trajectory , the location and the burden surface profile are analyzed in melter gasifier with a mixing charging of coal and direct reduction iron ( DRI ) at the same time.Considering the porosity of packed bed has an important effect on the gas flow distribution of melter gasifier , a method to calculate porosity has been proposed.The distribution of DRI and coal and the porosity in the radial direction are given under different charging patterns , which is necessary to judge the gas flow distribution and provide base data for further researching the melter gasifier for the next work in the future.The research results can be used to guide the operation of adjusting charging and provide important basis for optimizing the charging patterns in order to obtain the reasonable gas distribution.展开更多
Many rock avalanches were triggered by the Wenchuan earthquake on May 12, 2008 in southwest China. Protection galleries covered with a single soil layer are usually used to protect against rockfall. Since one-layer pr...Many rock avalanches were triggered by the Wenchuan earthquake on May 12, 2008 in southwest China. Protection galleries covered with a single soil layer are usually used to protect against rockfall. Since one-layer protection galleries do not have sufficient buffer capacity, a two-layered absorbing system has been designed. This study aims to find whether an expanded poly-styrol （EPS） cushion, which is used in the soil-covered protection galleries for shock absorption, could be positioned under dynamic loadings. The dynamic impacts of the two-layered absorbing system under the conditions of rock avalanches are numerically simulated through a 2D discrete dement method. By selecting reasonable parameters, a series of numerical experiments were conducted to find the best combination for the two- layered absorbing system. The values of the EPS layer area as a percentage of the total area were set as 0% （Sl）, 22~ （S2）, and 70% （$3）. 22~ of the area of the EPS layer was found to be a reasonable value, and experiments were conducted to find the best position of the EPS layer in the two-layered absorbing system. The numerical results yield useful conclusions regarding the interaction between the impacting avalanches and the two-layered absorbing system. The soil layer can absorb the shock energy effectively and S2 （0.4-m thick EPS cushion covered with soil layer） is the most efficient combination, which can reduce the impact force, compared with the other combinations.展开更多
With the development of high-speed and heavy-haul railway in China, problems like insufficient thickness of ballast bed and overlarge track stiffness are obvious. Ballast may break into small particles and their conta...With the development of high-speed and heavy-haul railway in China, problems like insufficient thickness of ballast bed and overlarge track stiffness are obvious. Ballast may break into small particles and their contact status will deteriorate under cyclic loading, resulting in ballast degradation. Discrete element method(DEM) was used to research improved performance of ballast bed using elastic sleeper. Clusters were generated by bonding spheres to model real ballasts, while broken bonds were utilized to distinguish breakage. Two kinds of ballast beds with elastic sleeper and conventional sleeper were established, respectively. After applying cyclic loading to the models, differences of mechanical properties between two models were analyzed by contrasting their dynamic behavior indexes, such as particle contact force, sleeper settlement, vibration velocity and acceleration, breakage characteristic. The results illustrate that compared with conventional sleeper, elastic sleeper increases sleeper settlement, while reduces ballast vibration and contact force between particles, which could depress ballast breakage.展开更多
The past decade has witnessed the substantial growth in research interests and progress on the subject of coupled hydro-mechanical processes in rocks and soils,driven mainly by the surge of research in unconventional ...The past decade has witnessed the substantial growth in research interests and progress on the subject of coupled hydro-mechanical processes in rocks and soils,driven mainly by the surge of research in unconventional hydrocarbon reservoirs and associated hazards.Many coupling techniques have been developed to include the effects of fluid flow in the discrete element method(DEM),and the techniques have been applied to a variety of geomechanical problems.Although these coupling methods have been successfully applied in various engineering fields,no single fluid/DEM coupling method is universal due to the complexity of engineering problems and the limitations of the numerical methods.For researchers and engineers,the key to solve a specific problem is to select the most appropriate fluid/DEM coupling method among these modeling technologies.The purpose of this paper is to give a comprehensive review of fluid flow/DEM coupling methods and relevant research.Given their importance,the availability or unavailability of best practice guidelines is outlined.The theoretical background and current status of DEM are introduced first,and the principles,applications,and advantages and disadvantages of different fluid flow/DEM coupling methods are discussed.Finally,a summary with speculation on future development trends is given.展开更多
The particulate discrete element method(DEM) can be employed to capture the response of rock,provided that appropriate bonding models are used to cement the particles to each other.Simulations of laboratory tests are ...The particulate discrete element method(DEM) can be employed to capture the response of rock,provided that appropriate bonding models are used to cement the particles to each other.Simulations of laboratory tests are important to establish the extent to which those models can capture realistic rock behaviors.Hitherto the focus in such comparison studies has either been on homogeneous specimens or use of two-dimensional(2D) models.In situ rock formations are often heterogeneous,thus exploring the ability of this type of models to capture heterogeneous material behavior is important to facilitate their use in design analysis.In situ stress states are basically three-dimensional(3D),and therefore it is important to develop 3D models for this purpose.This paper revisits an earlier experimental study on heterogeneous specimens,of which the relative proportions of weaker material(siltstone) and stronger,harder material(sandstone) were varied in a controlled manner.Using a 3D DEM model with the parallel bond model,virtual heterogeneous specimens were created.The overall responses in terms of variations in strength and stiffness with different percentages of weaker material(siltstone) were shown to agree with the experimental observations.There was also a good qualitative agreement in the failure patterns observed in the experiments and the simulations,suggesting that the DEM data enabled analysis of the initiation of localizations and micro fractures in the specimens.展开更多
A three-dimensional discrete element model of the connective type is presented. Moreover,a three-dimensional numerical analysis code,which can carry out the transitional pro- cess from connective model(for continuum)t...A three-dimensional discrete element model of the connective type is presented. Moreover,a three-dimensional numerical analysis code,which can carry out the transitional pro- cess from connective model(for continuum)to contact model(for non-continuum),is developed for simulating the mechanical process from continuum to non-continuum.The wave propagation process in a concrete block(as continuum)made of cement grout under impact loading is numer- ically simulated with this code.By comparing its numerical results with those by LS-DYNA,the calculation accuracy of the model and algorithm is proved.Furthermore,the failure process of the concrete block under quasi-static loading is demonstrated,showing the basic dynamic tran- sitional process from continuum to non-continuum.The results of calculation can be displayed by animation.The damage modes are similar to the experimental results.The two numerical examples above prove that our model and its code are powerful and efficient in simulating the dynamic failure problems accompanying the transition from continuum to non-continuum.It also shows that the discrete element method(DEM)will have broad prospects for development and application.展开更多
This study investigated the correlations between mechanical properties and mineralogy of granite using the digital image processing(DIP) and discrete element method(DEM). The results showed that the X-ray diffraction(...This study investigated the correlations between mechanical properties and mineralogy of granite using the digital image processing(DIP) and discrete element method(DEM). The results showed that the X-ray diffraction(XRD)-based DIP method effectively analyzed the mineral composition contents and spatial distributions of granite. During the particle flow code(PFC2D) model calibration phase, the numerical simulation exhibited that the uniaxial compressive strength(UCS) value, elastic modulus(E), and failure pattern of the granite specimen in the UCS test were comparable to the experiment. By establishing 351 sets of numerical models and exploring the impacts of mineral composition on the mechanical properties of granite, it indicated that there was no negative correlation between quartz and feldspar for UCS, tensile strength(σ_(t)), and E. In contrast, mica had a significant negative correlation for UCS, σ_(t), and E. The presence of quartz increased the brittleness of granite, whereas the presence of mica and feldspar increased its ductility in UCS and direct tensile strength(DTS) tests. Varying contents of major mineral compositions in granite showed minor influence on the number of cracks in both UCS and DTS tests.展开更多
基金funded by the project of the Major Scientific and Technological Projects of CNOOC in the 14th Five-Year Plan(No.KJGG2022-0701)the CNOOC Research Institute(No.2020PFS-03).
文摘To analyze the differences in the transport and distribution of different types of proppants and to address issues such as the short effective support of proppant and poor placement in hydraulically intersecting fractures,this study considered the combined impact of geological-engineering factors on conductivity.Using reservoir production parameters and the discrete elementmethod,multispherical proppants were constructed.Additionally,a 3D fracture model,based on the specified conditions of the L block,employed coupled(Computational Fluid Dynamics)CFD-DEM(Discrete ElementMethod)for joint simulations to quantitatively analyze the transport and placement patterns of multispherical proppants in intersecting fractures.Results indicate that turbulent kinetic energy is an intrinsic factor affecting proppant transport.Moreover,the efficiency of placement and migration distance of low-sphericity quartz sand constructed by the DEM in the main fracture are significantly reduced compared to spherical ceramic proppants,with a 27.7%decrease in the volume fraction of the fracture surface,subsequently affecting the placement concentration and damaging fracture conductivity.Compared to small-angle fractures,controlling artificial and natural fractures to expand at angles of 45°to 60°increases the effective support length by approximately 20.6%.During hydraulic fracturing of gas wells,ensuring the fracture support area and post-closure conductivity can be achieved by controlling the sphericity of proppants and adjusting the perforation direction to control the direction of artificial fractures.
基金a U.S. Federal Railroad Administration (FRA)BAA project,titled “Mitigation of Differential Movement at Railway Transitions for High-Speed Passenger Rail and Joint Passenger/Freight Corridors”the financial support provided by the China Scholarship Council (CSC),which funded Zhongyi Liu’s and Wenjing Li’s time and research efforts for this study
文摘Nonuniform track support and differential settlements are commonly observed in bridge approaches where the ballast layer can develop gaps at crosstie-ballast interfaces often referred to as a hanging crosstie condition.Hanging crossties usually yield unfavorable dynamic effects such as higher wheel loads,which negatively impact the serviceability and safety of railway operations.Hence,a better understanding of the mechanisms that cause hanging crossties and their effects on the ballast layer load-deformation characteristics is necessary.Since the ballast layer is a particulate medium,the discrete element method(DEM),which simulates ballast particle interactions individually,is ideal to explore the interparticle contact forces and ballast movements under dynamic wheel loading.Accurate representations of the dynamic loads from the train and track superstructure are needed for high-fidelity DEM modeling.This paper introduces an integrated modeling approach,which couples a single-crosstie DEM ballast model with a train–track–bridge(TTB)model using a proportional–integral–derivative control loop.The TTB–DEM model was validated with field measurements,and the coupled model calculates similar crosstie displacements as the TTB model.The TTB–DEM provided new insights into the ballast particle-scale behavior,which the TTB model alone cannot explore.The TTB–DEM coupling approach identified detrimental effects of hanging crossties on adjacent crossties,which were found to experience drastic vibrations and large ballast contact force concentrations.
基金the project of the State Key Laboratory of Petroleum Resources and Engineering(No.PRE/open-2307)the CNOOC Research Institute(No.2020PFS-03).
文摘Hydraulic fracturing,an effective method for enhancing coal seam productivity,largely determines coalbed methane(CBM)production,which is significantly influenced by geological and engineering factors.This study focuses on the L block to investigate the mechanisms influencing efficient fracture propagation and enhanced stimulated reservoir volume(SRV)in fracturing.To explore the mechanisms influencing effective fracture propagation and enhanced SRV,the L block was selected as the research object,with a comprehensive consideration of geological background,reservoir properties,and dynamic production data.By combining the discrete lattice method with numer-ical analysis and true triaxial experimental simulation,the fracture morphology of a single cluster and the propagation patterns of multiple clusters of complex fractures were obtained.Additionally,the optimization of temporary plugging timing and the fracture map under multiple factors were innovatively proposed.Results indicate that greater flow rate and viscosity can effectively overcome the stress shadow effect of the outermost fractures(1st and 6th clusters),increasing the fracture pressure of the single cluster and the equilibrium degree of multiple fracture propagation,thus forming a more complex fracture network.Moreover,when viscosity exceeds 45 pressure concentrates at fracture mPa⋅s,tips,promoting discontinuous propagation and reducing flow resistance.Conversely,increased gangue thickness and spacing between horizontal wells increase the vertical propagation pressure,suppressing fracture growth and reducing central flow velocity.This study provides a multi-cluster fracture propagation map for optimizing volumetric fracturing in coal seams and suggests that the optimal temporary plugging time significantly enhances the SRV.
基金the financial support from National Key R&D Program of China(Grant number:2024YFC2815100)Natural Science Foundation of China(Grant number:52322110)Beijing Nova Program(Grant number:20230484341).
文摘Deepwater drilling riser is the key equipment connecting the subsea wellhead and floating drilling platform.Due to complex marine environment,vortex-induced vibration(ViV)will be generated on riser,which will induce fatigue failure and even cause unpredictable drilling accidents.Therefore,it is important to study the ViV characteristics of deepwater drilling riser and reveal the main controlling factors for ensuring the safe and efficient operation of deepwater drilling engineering.In this paper,the ViV of deepwater drilling riser is numerically simulated in time domain based on the discrete vortex method(DvM).A hydrodynamic analysis model and governing equation of VIV is proposed with considering the effect of riser motion using DVM and slice method,where the governing equation is solved by Runge-Kutta method.Model validation is performed,which verified the correctness and accuracy of the mechanical model and the solution method.On this basis,the influence of the number of control points,current velocity,riser outer diameter,shear flow and top tension on the ViV characteristics of deepwater drilling risers are discussed in detail.The results show that with the increase of current velocity,the vibration amplitude of deepwater drilling riser decreases obviously,while the vibration frequency increases gradually.However,if the outer diameter of riser increases,the vibration amplitude increases,while the vibration frequency decreases gradually.The top tension also has great influence on the VIV of riser.When the top tension is 1.25 G,the VIV is suppressed to a certain extent.This study has guiding significance for optimal design and engineering control of deepwater drilling riser.
基金funded by the National Natural Science Foundation of China(No.51978048).
文摘The homogeneity of aggregate blend has a significant influence on the performance of asphalt mixture.The composition of aggregate blend,including the size combination and the mass ratio between each size particles(MRESP),is an important factor affecting the homogeneity.This study investigated the influence of the size combination and MRESP on the distribution homogeneity of particles in aggregate blend using discrete element method(DEM).An indicator quantifying the distribution homogeneity was established according to the coefficient of variation(CV)for particle number.Two-size,three-size,and four-size aggregate blends with various compositions were designed.Laboratory tests show the DEM simulation is feasible.The particle distribution homogeneity in various blends was analyzed.The results showed the distribution homogeneity of each size particles in a blend is closely related to their mass fraction.The higher the mass fraction of the particles,the more homogeneous the distribution of them.The MRESP has no significant influence on the homogeneity of the blend composed of only coarse aggregates.However,the homogeneity of the blend composed of coarse and fine aggregates improves gradually with the increase of the mass fraction of fine aggregates.The smaller the maximum particle size in a blend,the better the homogeneity.It is suggested that the mass fraction of fine aggregates should be between 33%and 50%for achieving good homogeneity of aggregate blends.The research results can provide a reference for gradation design of asphalt mixture.
基金Project(52108361)supported by the National Natural Science Foundation of ChinaProjects(BK20231217,BK20220265)supported by the Basic Research Program of Jiangsu Province,China+5 种基金Project(sklhse-KF-2025-D-02)supported by the Open Research Fund Program of the State Key Laboratory of Hydroscience and Engineering,ChinaProject(2023ZB15)supported by the Independent Research Project of the State Key Laboratory of Subtropical Building and Urban Science,ChinaProject(SKLGME023001)supported by the Key Laboratory of Geomechanics and Geotechnical Engineering Safety,the Chinese Academy of SciencesProject(2025A04J3992)supported by the Basic and Applied Basic Research Project of the Guangzhou Science and Technology Bureau,ChinaProject(SKLGP2022Z015)supported by the State Key Laboratory of Geohazard Prevention and Geoenvironment Protection Independent Research Project,ChinaProjects(2023YFS0436,2024NSFSC1715)supported by the Science and Technology Department of Sichuan Province,China。
文摘Steep bedding slopes are widely distributed in Southwestern China’s mountainous regions and have complex seismic responses and instability risks,causing casualties and property losses.Considering the high-seismic-intensity environment,the dynamic failure evolution and instability mechanism of high-steep bedding slopes are simulated via the discrete element method and shaking table test.The dynamic response characteristics and cumulative failure effects of slopes subjected to continuous ground motion are investigated.The results show that the dynamic response characteristics of slopes under continuous earthquakes are influenced by geological and topographic conditions.Elevation has a distinct impact on both the slope interior and surface,with amplification effects more pronounced on the surface.The weak interlayers have different influences on the dynamic amplification effect of slopes.Weak interlayers have dynamic magnification effects on the slope surface at relative elevations of 0-0.33 and 0.82-1.0 but have weakening effects between 0.33 and 0.82.Moreover,the weak interlayers also have controlling effects on the dynamic instability mode of slopes.The characteristics of intergranular contact failure,fracture propagation,and displacement distribution are analyzed to reveal the dynamic failure evolution and instability mechanism through the discrete-element model.The dynamic instability process of slopes includes three stages:fracture initiation(0-0.2g),fracture expansion(0.2g-0.3g),and sliding instability(0.3g-0.6g).This work can provide a valuable reference for the seismic stability and reinforcement of complex slopes.
基金supported by the National Natural Science Foundation of China(Grant No.U2242214)the Guangdong Basic and Applied Basic Research Foundation(Grant No.2024A1515010927)+3 种基金the Humanities and Social Science Foundation of the Ministry of Education in China(Grant No.24YJCZH163)the Fujian Provincial Units Special Funds for Education and Research(Grant No.2022639)Fundamental Research Funds for the Central Universities,Sun Yatsen University(Grant No.24qnpy044)partly supported by the Open Research Fund of Key Laboratory of Analytical Mathematics and Applications(Fujian Normal University),Ministry of Education,P.R.China(Grant No.JAM2405)。
文摘The Richtmyer–Meshkov(RM)instability plays an important role in various natural and engineering fields such as inertial confinement fusion.In this study,the effect of relaxation time on the RM instability under reshock impact is investigated using a two-component discrete Boltzmann method.The hydrodynamic and thermodynamic characteristics of the fluid system are comprehensively analyzed from the perspectives of the density gradient,vorticity,kinetic energy,mixing degree,mixing width and non-equilibrium intensity.Simulation results indicate that for longer relaxation time,the diffusion and dissipation are enhanced,the physical gradients decrease,and the growth of the interface is suppressed.Furthermore,the non-equilibrium manifestations show complex patterns,driven by the competitive physical mechanisms of the diffusion,dissipation,shock wave,rarefaction wave,transverse wave and fluid instabilities.These findings provide valuable insight into the fundamental mechanism of compressible fluid flows.
基金supported by the National Natural Science Foundation of China(Grant No.52304003)the Natural Science Foundation of Sichuan Province(Grant No.2024NSFSC0961)the Postdoctoral Fellowship Program of CPSF(Grant No.GZB20230090).
文摘The glutenite reservoir is strongly heterogeneous due to the random distribution of gravels, making it challenging to perform hydraulic fracturing effectively. To solve this issue, it is essential to study interaction behavior between hydraulic fractures(HFs) and gravels. A coupled hydro-mechanical model is proposed for HF propagation in glutenite using a grain-based discrete element method. This paper first investigates the dynamic evolution of HFs in glutenite, then analyzes the influences of various factors such as horizontal stress difference(Δσ), minimum horizontal stress(σh), gravel content(Vg), gravel size(dg), and stiffness ratio of gravel to matrix(Rs) on HF propagation geometries. Results show that penetrating the gravel is the primary HF-gravel interaction behavior, which follows sequential and staggered initiation modes. Bypassing the gravel is the secondary behavior, which obeys the sequential initiation mode and occurs when the orientation of the gravel boundary is inclined to the maximum horizontal stress(σH). An offset along the gravel boundary is usually formed while penetrating gravels, and the offsets may cause fracture widths to decrease by 37.8%-84.4%. Even if stress dominates the direction of HF propagation, HFs still tend to deflect within gravels. The deviation angle from σH decreases with rising Δσand increases with the increase of dgand Rs. Additionally, intra-gravel shear HFs(IGS-HFs) are prone to be generated in coarse-grained glutenite under high Δσ, while more gravel-bypassing shear HFs(GBSHFs) tend to be created in argillaceous glutenite with high Rsthan in sandy glutenite with low Rs. The findings above prompt the emergence of a novel HF propagation pattern in glutenite, which helps to understand the real HF geometries and to provide theoretical guidance for treatments in the field.
基金the financial support provided by Tianfu Yongxing Laboratory Organized Research Project Funding(No.2023CXXM01)the ARC linkage program(No.LP200100420).
文摘Ceramic spheres,typically with a particle diameter of less than 0.8 mm,are frequently utilized as a critical proppant material in hydraulic fracturing for petroleum and natural gas extraction.Porous ceramic spheres with artificial inherent pores are an important type of lightweight proppant,enabling their transport to distant fracture extremities and enhancing fracture conductivity.However,the focus frequently gravitates towards the low-density advantage,often overlooking the pore geometry impacts on compressive strength by traditional strength evaluation.This paper numerically bypasses such limitations by using a combined finite and discrete element method(FDEM)considering experimental results.The mesh size of the model undergoes validation,followed by the calibration of cohesive element parameters via the single particle compression test.The stimulation elucidates that proppants with a smaller pore size(40μm)manifest crack propagation evolution at a more rapid pace in comparison to their larger-pore counterparts,though the influence of pore diameter on overall strength is subtle.The inception of pores not only alters the trajectory of crack progression but also,with an increase in porosity,leads to a discernible decline in proppant compressive strength.Intriguingly,upon crossing a porosity threshold of 10%,the decrement in strength becomes more gradual.A denser congregation of pores accelerates crack propagation,undermining proppant robustness,suggesting that under analogous conditions,hollow proppants might not match the strength of their porous counterparts.This exploration elucidates the underlying mechanisms of proppant failure from a microstructural perspective,furnishing pivotal insights that may guide future refinements in the architectural design of porous proppant.
基金financially supported by the National Key Research and Development Plan(2023YFC2811001)the National Natural Science Foundation of China(42206233)the Taishan Scholars Program(tsqn202312280,tsqn202306297)。
文摘Hydraulic fracturing technology has played an important role in the exploitation of unconventional oil and gas resources,however,its application to gas hydrate reservoirs has been rarely studied.Currently,there is still limited understanding of the propagation and extension of fractures around the wellbore during the fracturing process of horizontal wells in hydrate reservoirs,as well as the stress interference patterns between fractures.This study simulates hydraulic fracturing processes in hydrate reservoirs using a fluidsolid coupling discrete element method(DEM),and analyzes the impacts of hydrate saturation and geological and engineering factors on fracture extension and stress disturbance.The results show that hydraulic fracturing is more effective when hydrate saturation exceeds 30%and that fracture pressure increases with saturation.The increase in horizontal stress differential enhances the directionality of fracture propagation and reduces stress disturbance.The distribution uniformity index(DUI)reveals that injection pressure is directly proportional to the number of main fractures and inversely proportional to fracturing time,with fracturing efficiency depending on the spacing between injection points and the distance between wells.This work may provide reference for the commercial exploitation of natural gas hydrates.
基金National Natural Science Foundation of China,Grant/Award Numbers:U22A20598,52104107National Key Research and Development Program of China,Grant/Award Numbers:2023YFC2907300,2019YFE0118500,2019YFC1904304Natural Science Foundation of Jiangsu Province,Grant/Award Number:BK20200634。
文摘Gas storage in abandoned mines is one way to reuse waste space resources.The surrounding rock of gas storage reservoirs in underground roadways undergoes damage and deformation under the cyclic loading of gas charging and discharging,which can pose a risk to the safety of the reservoirs.This study establishes a true triaxial numerical model of rock mass with the discrete element method(DEM)and explores the crack evolution of surrounding rock of underground gas storage during cyclic loading and unloading.Also,a damage evolution model in numerical analysis considering residual deformation is developed to explain the experimental results.As was revealed,cyclic loading and unloading resulted in fatigue damage in the specimen and caused strength deterioration of the specimen.During the loading process,the uniformly distributed force chains of the rock mass redistributed,evolving gradually to mostly transverse force chains.This contributed to the appearance of blank areas in the force chains when through cracks appear.The ratio of tensile cracks to shear cracks gradually decreases and finally stabilizes at 7:1.The damage evolution model considering residual strain can be mutually verified with the numerical simulation results.Based on the DEM model,it was found that there was a certain threshold of confining pressure.When the confining pressure exceeded 30 MPa,the deformation to ductility of sandstone samples began to accelerate,with a greater residual strength.This study provides a theoretical basis for analyzing the long-term mechanical behavior of surrounding rock of gas storage in abandoned mines.
基金The National Natural Science Foundation of China(No.51108081)
文摘In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method （DEM）. A digital specimen generation procedure considering aggregate gradation and irregular shape is developed based on the probability theory and the Monte Carlo method. The virtual rutting test is then conducted based on the generated digital specimen. In addition, on the basis of the time-temperature superposition （TTS） principle, a calculation method is used to reduce the computation time of the virtual rutting test. The simulation results are compared with the laboratory measurements. The results show that the calculation method based on the TFS principle in the discrete element （DE） viscoelastic model can significantly reduce the computation time. The deformation law of asphalt mixtures in the virtual rutting test is similar to the laboratory measurements, and the deformation and the dynamic stability of the virtual rutting test are slightly greater than the laboratory measurements. The two-dimensional virtual rutting test can predict the permanent deformation performance of asphalt mixtures.
基金supported by the Young Scientists Fund of the National Natural Science Foundation of China(No.41304082)the Young Scientists Fund of the Natural Science Foundation of Hebei Province(No.D2014403011)the Geological survey project of China Geological Survey(No.12120114090201)
文摘We conducted a study on the numerical calculation and response analysis of a transient electromagnetic field generated by a ground source in geological media. One solution method, the traditional discrete image method, involves complex operation, and its digital filtering algorithm requires a large number of calculations. To solve these problems, we proposed an improved discrete image method, where the following are realized： the real number of the electromagnetic field solution based on the Gaver-Stehfest algorithm for approximate inversion, the exponential approximation of the objective kernel function using the Prony method, the transient electromagnetic field according to discrete image theory, and closed-form solution of the approximate coefficients. To verify the method, we tentatively calculated the transient electromagnetic field in a homogeneous model and compared it with the results obtained from the Hankel transform digital filtering method. The results show that the method has considerable accuracy and good applicability. We then used this method to calculate the transient electromagnetic field generated by a ground magnetic dipole source in a typical geoelectric model and analyzed the horizontal component response of the induced magnetic field obtained from the ＂ground excitation-stratum measurement method. We reached the conclusion that the horizontal component response of a transient field is related to the geoelectric structure, observation time, spatial location, and others. The horizontal component response of the induced magnetic field reflects the eddy current field distribution and its vertical gradient variation. During the detection of abnormal objects, positions with a zero or comparatively large offset were selected for the drill- hole measurements or a comparatively long observation delay was adopted to reduce the influence of the ambient field on the survey results. The discrete image method and forward calculation results in this paper can be used as references for relevant research.
基金Item Sponsored by Fundamental Research Funds for Central Universities of China ( N090402021 )
文摘COREX process is one of the earliest industrialized smelting reduction ironmaking technology.A numerical simulation model based on discrete element method ( DEM ) has been developed to analyze the burden distribution in the melter gasifier of COREX process.The DEM considering the collisions between particles can directly reproduce the charging process.The burden trajectory , the location and the burden surface profile are analyzed in melter gasifier with a mixing charging of coal and direct reduction iron ( DRI ) at the same time.Considering the porosity of packed bed has an important effect on the gas flow distribution of melter gasifier , a method to calculate porosity has been proposed.The distribution of DRI and coal and the porosity in the radial direction are given under different charging patterns , which is necessary to judge the gas flow distribution and provide base data for further researching the melter gasifier for the next work in the future.The research results can be used to guide the operation of adjusting charging and provide important basis for optimizing the charging patterns in order to obtain the reasonable gas distribution.
基金financial support from the Project of National Science Foundation of China(Grant No.41272346)the National Outstanding Youth Funds(Grant No.41225011)+2 种基金financial support from the Science & Technology Research Plan of China Railway Eryuan Engineering Group CO.LTD (Grant No.13164196(13-15))the Project of National Science Foundation of China(Grant Nos. 41472293,91430105)"hundred talents" program of CAS
文摘Many rock avalanches were triggered by the Wenchuan earthquake on May 12, 2008 in southwest China. Protection galleries covered with a single soil layer are usually used to protect against rockfall. Since one-layer protection galleries do not have sufficient buffer capacity, a two-layered absorbing system has been designed. This study aims to find whether an expanded poly-styrol （EPS） cushion, which is used in the soil-covered protection galleries for shock absorption, could be positioned under dynamic loadings. The dynamic impacts of the two-layered absorbing system under the conditions of rock avalanches are numerically simulated through a 2D discrete dement method. By selecting reasonable parameters, a series of numerical experiments were conducted to find the best combination for the two- layered absorbing system. The values of the EPS layer area as a percentage of the total area were set as 0% （Sl）, 22~ （S2）, and 70% （$3）. 22~ of the area of the EPS layer was found to be a reasonable value, and experiments were conducted to find the best position of the EPS layer in the two-layered absorbing system. The numerical results yield useful conclusions regarding the interaction between the impacting avalanches and the two-layered absorbing system. The soil layer can absorb the shock energy effectively and S2 （0.4-m thick EPS cushion covered with soil layer） is the most efficient combination, which can reduce the impact force, compared with the other combinations.
基金Project(U1234211)supported by the National Natural Science Foundation of ChinaProject(2013G009-B)supported by China Railway Corporation
文摘With the development of high-speed and heavy-haul railway in China, problems like insufficient thickness of ballast bed and overlarge track stiffness are obvious. Ballast may break into small particles and their contact status will deteriorate under cyclic loading, resulting in ballast degradation. Discrete element method(DEM) was used to research improved performance of ballast bed using elastic sleeper. Clusters were generated by bonding spheres to model real ballasts, while broken bonds were utilized to distinguish breakage. Two kinds of ballast beds with elastic sleeper and conventional sleeper were established, respectively. After applying cyclic loading to the models, differences of mechanical properties between two models were analyzed by contrasting their dynamic behavior indexes, such as particle contact force, sleeper settlement, vibration velocity and acceleration, breakage characteristic. The results illustrate that compared with conventional sleeper, elastic sleeper increases sleeper settlement, while reduces ballast vibration and contact force between particles, which could depress ballast breakage.
基金supported by the National Natural Science Foundation of China (Grant Nos. 41772286 and 42077247)the Fundamental Research Funds for the Central Universities, China
文摘The past decade has witnessed the substantial growth in research interests and progress on the subject of coupled hydro-mechanical processes in rocks and soils,driven mainly by the surge of research in unconventional hydrocarbon reservoirs and associated hazards.Many coupling techniques have been developed to include the effects of fluid flow in the discrete element method(DEM),and the techniques have been applied to a variety of geomechanical problems.Although these coupling methods have been successfully applied in various engineering fields,no single fluid/DEM coupling method is universal due to the complexity of engineering problems and the limitations of the numerical methods.For researchers and engineers,the key to solve a specific problem is to select the most appropriate fluid/DEM coupling method among these modeling technologies.The purpose of this paper is to give a comprehensive review of fluid flow/DEM coupling methods and relevant research.Given their importance,the availability or unavailability of best practice guidelines is outlined.The theoretical background and current status of DEM are introduced first,and the principles,applications,and advantages and disadvantages of different fluid flow/DEM coupling methods are discussed.Finally,a summary with speculation on future development trends is given.
文摘The particulate discrete element method(DEM) can be employed to capture the response of rock,provided that appropriate bonding models are used to cement the particles to each other.Simulations of laboratory tests are important to establish the extent to which those models can capture realistic rock behaviors.Hitherto the focus in such comparison studies has either been on homogeneous specimens or use of two-dimensional(2D) models.In situ rock formations are often heterogeneous,thus exploring the ability of this type of models to capture heterogeneous material behavior is important to facilitate their use in design analysis.In situ stress states are basically three-dimensional(3D),and therefore it is important to develop 3D models for this purpose.This paper revisits an earlier experimental study on heterogeneous specimens,of which the relative proportions of weaker material(siltstone) and stronger,harder material(sandstone) were varied in a controlled manner.Using a 3D DEM model with the parallel bond model,virtual heterogeneous specimens were created.The overall responses in terms of variations in strength and stiffness with different percentages of weaker material(siltstone) were shown to agree with the experimental observations.There was also a good qualitative agreement in the failure patterns observed in the experiments and the simulations,suggesting that the DEM data enabled analysis of the initiation of localizations and micro fractures in the specimens.
基金Project supported by the National Natural Science Foundation of China(Nos.59978005 and 10232024)the National Distinguished Youth Fund of China(No.10025212).
文摘A three-dimensional discrete element model of the connective type is presented. Moreover,a three-dimensional numerical analysis code,which can carry out the transitional pro- cess from connective model(for continuum)to contact model(for non-continuum),is developed for simulating the mechanical process from continuum to non-continuum.The wave propagation process in a concrete block(as continuum)made of cement grout under impact loading is numer- ically simulated with this code.By comparing its numerical results with those by LS-DYNA,the calculation accuracy of the model and algorithm is proved.Furthermore,the failure process of the concrete block under quasi-static loading is demonstrated,showing the basic dynamic tran- sitional process from continuum to non-continuum.The results of calculation can be displayed by animation.The damage modes are similar to the experimental results.The two numerical examples above prove that our model and its code are powerful and efficient in simulating the dynamic failure problems accompanying the transition from continuum to non-continuum.It also shows that the discrete element method(DEM)will have broad prospects for development and application.
基金This research was supported by the Department of Mining Engineering at the University of Utah.In addition,the lead author wishes to acknowledge the financial support received from the Talent Introduction Project,part of the Elite Program of Shandong University of Science and Technology(No.0104060540171).
文摘This study investigated the correlations between mechanical properties and mineralogy of granite using the digital image processing(DIP) and discrete element method(DEM). The results showed that the X-ray diffraction(XRD)-based DIP method effectively analyzed the mineral composition contents and spatial distributions of granite. During the particle flow code(PFC2D) model calibration phase, the numerical simulation exhibited that the uniaxial compressive strength(UCS) value, elastic modulus(E), and failure pattern of the granite specimen in the UCS test were comparable to the experiment. By establishing 351 sets of numerical models and exploring the impacts of mineral composition on the mechanical properties of granite, it indicated that there was no negative correlation between quartz and feldspar for UCS, tensile strength(σ_(t)), and E. In contrast, mica had a significant negative correlation for UCS, σ_(t), and E. The presence of quartz increased the brittleness of granite, whereas the presence of mica and feldspar increased its ductility in UCS and direct tensile strength(DTS) tests. Varying contents of major mineral compositions in granite showed minor influence on the number of cracks in both UCS and DTS tests.
