Size reduction of the gas turbines(GT)by reducing the inlet S-shaped diffuser length increases the powerto-weight ratio.It improves the techno-economic features of the GT by lesser fuel consumption.However,this Length...Size reduction of the gas turbines(GT)by reducing the inlet S-shaped diffuser length increases the powerto-weight ratio.It improves the techno-economic features of the GT by lesser fuel consumption.However,this Length reduction of a bare S-shaped diffuser to an aggressive S-shaped diffuser would risk flow separation and performance reduction of the diffuser and the air intake of the GT.The objective of this research is to propose and assess fitted energy promoters(EPs)to enhance the S-shaped diffuser performance by controlling and modifying the flow in the high bending zone of the diffuser.After experimental assessment,the work has been extended to cover more cases by numerical investigations on bare,bare aggressive,and aggressive with energy promoters S-shaped diffusers.Three types of EPs,namely co-rotating low-profile,co-rotating streamline sheet,and trapezoidal submerged EPs were tested with various combinations over a range of Reynolds numbers from 40,000 to 75,000.The respective S-shaped diffusers were simulated by computational fluid dynamics(CFD)using ANSYS software adopting a steady,3D,standard k-εturbulence model to acquire the details of the flow structure,which cannot be visualized in the experiment.The diffuser performance has been evaluated by the performance indicators of static pressure recovery coefficient,total pressure loss coefficient,and distortion coefficient(DC(45°)).The enhancements in the static pressure recovery of the S-shaped aggressive diffuser with energy promoters are 19.5%,22.2%,and 24.5%with EPs at planes 3,4 and 5,respectively,compared to the aggressive bare diffuser.In addition,the installation of the EPs resulted in a DC(45°)reduction at the outlet plane of the diffuser of about 43%at Re=40,000.The enhancements in the performance parameters confirm that aggravating the internal flow eliminates the flow separation and enhances the GT intake efficiency.展开更多
The thermocline energy storage tank(TEST)serves as a crucial component in thermal energy storage systems,utilizing the working fluid that enters through a diffuser to store and harness energy.However,the conventional ...The thermocline energy storage tank(TEST)serves as a crucial component in thermal energy storage systems,utilizing the working fluid that enters through a diffuser to store and harness energy.However,the conventional double-plate radial diffuser is ill-suited for a single-medium TEST’s full tank storage due to its unidirectional fluid inflow.There has been a notable lack of optimization analysis of diffusers.Two innovative tubular diffuser designs with reduced cross-sectional areas have been introduced:the annular-arranged diffuser(AAD)and the cross-arranged diffuser(CAD).To elucidate the impact of diffuser designs on energy storage efficiency,a 3D transient computational fluid dynamics(CFD)model was established to simulate a thermocline formation under two diffuser types.The model was validated against experimental data.Results showed that the thermocline of AAD was 11.39%thinner than that of a traditional double-plate diffuser.In the process of charging and discharging,the time-varying thermocline and factors influencing thermocline thickness were analyzed.Results indicate that in the mixed dominant region,increased turbulent kinetic energy correlates with reduced thermocline thickness.Notably,the AAD’s stable thermocline was 4.23%and 5.41%thinner than the CAD’s during charging and discharging,respectively,making the AAD preferable for engineering applications.The effects of tube diameter and orifice opening angle on temperature stratification performance were also examined.The findings suggest that an inclined impact jet and large-diameter tubes are more conducive to temperature stratification.Moreover,an orifice diameter optimization method was developed,which can decrease the thermocline by 6.78%.展开更多
The dump diffuser is an important component in advanced annular combustor, and its performance affects greatly the fluid field and pressure loss of the combustor. This paper presents the characteristics of the total p...The dump diffuser is an important component in advanced annular combustor, and its performance affects greatly the fluid field and pressure loss of the combustor. This paper presents the characteristics of the total pressure loss. Experiments and numerical simulations, keeping the inlet March number of prediffuser constant ( Ma =0 20), are carried out to obtain the regularity of the total pressure loss. It varies with the relative dump gap ( δ =1 2～3 0)by changing the position of prediffuser and combustor liner, respectively. Research shows that there exists the minimum total pressure loss ( σ *=1 6%～1 75%) when relative dump gap δ is about 1 8.展开更多
In order to improve the performances of an 11 cm-diameter turbine engine,this article suggests to substitute a new-style micro diffuser redesigned based on a new concept for the traditional diffuser having poor perfor...In order to improve the performances of an 11 cm-diameter turbine engine,this article suggests to substitute a new-style micro diffuser redesigned based on a new concept for the traditional diffuser having poor performances. The new diffuser comprises integral blades and splitters,which are taken for a series of ducts in designing. This article investigates the effects of the cross-section area distribution along the flow path on the redesigned diffuser＇s performances. Having furnished with the new diffuser in place of the original vaned one,the 11 cm-diameter prototype engine is tested on the rig for its performances. CFD and experiments have shown that the improved diffuser with the unchanged original size has gained excellent performance parameters of pressure coefficient over 0.65 and total pressure recovery coefficient over 0.9. Equipped with the redesigned micro diffuser,the engine increases the thrust by 11% and decreases the specific fuel consumption by 9%.展开更多
To expand the stable operating range of compressors, understanding the mechanism of flow instability at low flow rates is necessary. In this paper, the mechanism of stall and surge in a centrifugal compressor with a v...To expand the stable operating range of compressors, understanding the mechanism of flow instability at low flow rates is necessary. In this paper, the mechanism of stall and surge in a centrifugal compressor with a variable vaned diffuser is experimentally investigated, where the diffuser blade setting angle can be adjusted. Many dynamic pressure transducers are mounted on the casing surface of the compressor. From the design condition to surge, dynamic pressure data is recorded throughout the gradual process. According to the signal developing status, the typical modes of compressor instability are defined in detail, such as stall, mild surge, and deep surge. A relatively high-frequency stall wave originates in the impeller and propagates to the diffuser, and finally stimulates a deep surge in the compressor. The compressor behavior during surge differs at different diffuser vane angles. When the diffuser vane angle is adjusted, both the unstable form and the core factor affecting the overall machine stability change. A specific indicator is proposed to measure the instability of each component in a compressor, which can be used to determine the best region for stability extension technologies, such as a holed casing treatment, in different compressor applications.展开更多
The paper presents analysis of the performance and the internal flow behaviour in the vaned diffuser of a radial flow pump using PIV(particle image velocimetry)and pressure probe traverses.PIV measurements have alread...The paper presents analysis of the performance and the internal flow behaviour in the vaned diffuser of a radial flow pump using PIV(particle image velocimetry)and pressure probe traverses.PIV measurements have already been performed at middle height inside one diffuser channel passage for a given speed of rotation and various mass flow rates.These results have been already presented in several previous communications.New experiments have been performed using a three-hole pressure probe traverses from hub to shroud diffuser width at different radial locations between the two diffuser geometrical throats.Numerical simulations are also realized with the commercial codes Star CCM+7.02.011 and CFX.Frozen rotor and fully unsteady calculations of the whole pump have been performed.Comparisons between numerical results,previous experimental PIV results and new probe traverses one's are presented and discussed for one mass flow rate.In this respect,a first attempt to take into account fluid leakages between the rotating and fixed part of the pump has been checked since it may affects the real flow structure inside the diffuser.展开更多
The influence of diffuser parameters, including the riser spacing, port number in a riser, injection angle, port arrangement, etc., on the surface initial dilution is experimentally investigated. The relative density ...The influence of diffuser parameters, including the riser spacing, port number in a riser, injection angle, port arrangement, etc., on the surface initial dilution is experimentally investigated. The relative density difference between the effluent and the sea water in the model is the same as that in the prototype, and the effect of the cross current is simulated by an inverse model technique. Based on the result analysis, the arrangement with more ports in a riser and larger riser spacing is suggested to save construction cost. The relationship between the Reynolds number based on the port diameter and velocity, and the surface initial dilution is also explored, and the critical Reynolds number is proposed.展开更多
Based on the boundary condition of field engineering, numerical simulations of28 conditions of existing diffusers of 3 structure types were investigated by ComputationalFluid Dynamics software package, and there were ...Based on the boundary condition of field engineering, numerical simulations of28 conditions of existing diffusers of 3 structure types were investigated by ComputationalFluid Dynamics software package, and there were the problems of larger structure resistanceand lower diffusing efficiency of these diffusers by analysis of CFD results.Thestructure outlines of the energy-saving diffuser were constructed by the application ofstream function and potential function superimposing.On the basis of numerical simulationsof energy-saving diffusers of 5 area-enlarging ratios, structural resistances and diffusingefficiencies of 5 energy-saving diffusers were comparatively analyzed, and therange from 2.00 to 2.31 of the rational area-enlarging ratio of energy-saving diffusers wasderived.The optimization area-enlarging ratio of the energy-saving diffuser was presently2.28 through comparable analysis.From the above, the results show that the coefficient ofperformance of the energy-saving diffuser is better than 3 existing diffusers.展开更多
The internal turbulent flow in conical diffuser is a very complicated adverse pressure gradient flow.DLR k-ε turbulence model was adopted to study it.The every terms of the Laplace operator in DLR k-ε turbulence mod...The internal turbulent flow in conical diffuser is a very complicated adverse pressure gradient flow.DLR k-ε turbulence model was adopted to study it.The every terms of the Laplace operator in DLR k-ε turbulence model and pressure Poisson equation were discretized by upwind difference scheme.A new full implicit difference scheme of 5-point was constructed by using finite volume method and finite difference method.A large sparse matrix with five diagonals was formed and was stored by three arrays of one dimension in a compressed mode.General iterative methods do not work wel1 with large sparse matrix.With algebraic multigrid method(AMG),linear algebraic system of equations was solved and the precision was set at 10-6.The computation results were compared with the experimental results.The results show that the computation results have a good agreement with the experiment data.The precision of computational results and numerical simulation efficiency are greatly improved.展开更多
Laboratory experiments were conducted to investigate the mixture of wastewater discharged from a submerged multiport diffuser in the Nantong sea-area. The process was then simulated with a three-dimensional numerical ...Laboratory experiments were conducted to investigate the mixture of wastewater discharged from a submerged multiport diffuser in the Nantong sea-area. The process was then simulated with a three-dimensional numerical model. The plane or line patch was used to impose the discharge momentum flux in the near field. A comparison of model simulation with laboratory experiments shows that the proposed model can be used to simulate the shapes of pollution plumes, the distributions of excess concentration, and the velocity induced by a coflowing diffuser in proximity to a shoreline boundary. From the numerical simulation and laboratory experiments, it is recommended that the multiport diffuser be placed in a hydrodynamically active sea-area.展开更多
Centrifugal compressors with parallel-wall and contracting wall vaneless diffuser are designed by using centrifugal compressor computer-aided integrated design system. The internal flow fields of the compressor are ca...Centrifugal compressors with parallel-wall and contracting wall vaneless diffuser are designed by using centrifugal compressor computer-aided integrated design system. The internal flow fields of the compressor are calculated by solving three-dimensional Navier-Stokes equation. Four aspects are investigated and calculation results show that the total efficiencies and total pressure ratios of the compressor with contracting wall vandess diffuser is higher than that of the compressor with parallel-wall. The jet and wake don＇t mix rapidly inside vandess diffuser. The outlet blade lean angle doesn＇t affect the compressor performance. The greater the mass flow rate through impeller, the more uneven the velocity distribution at impeller outlet is.展开更多
The wind turbine with a flanged-diffuser shroud—so called “wind-lens turbine”—is developed as one of high performance wind turbines by Ohya et al. In this paper, the wind turbine performance is investigated for bo...The wind turbine with a flanged-diffuser shroud—so called “wind-lens turbine”—is developed as one of high performance wind turbines by Ohya et al. In this paper, the wind turbine performance is investigated for both steady and unsteady winds. The compact-type wind lens turbine shows higher efficiency than the only rotor wind turbine. Also, the flow structure around the compact-type wind turbine is made clear by CFD and PIV in steady wind. Furthermore, the performances of the only rotor and the compact-type wind-lens turbines for unsteady wind are experimentally and numerically investigated. Experimental and numerical results are presented to demonstrate the dependence of frequency of the harmonic oscillating velocity wind on power coefficient. Consequently, the compact-type wind-lens turbine show better performance than the only rotor one in sinusoidally oscillating velocity wind. Furthermore, the numerical estimation can predict the power coefficient in the oscillating flows to an accuracy of 94% to 102%. In addition, the dependence of the turbine performance on turbulent intensity and vortex scale of natural fluctuating wind is presented.展开更多
The plume interaction above an alternating diffuser in stagnant water is studied with 3D Reynolds-averaged NavierStokes equations （RANS） combined with a buoyancy-extended κ-ε model. The steady three-dimensional tu...The plume interaction above an alternating diffuser in stagnant water is studied with 3D Reynolds-averaged NavierStokes equations （RANS） combined with a buoyancy-extended κ-ε model. The steady three-dimensional turbulent flow and temperature fields are computed by use of the finite volume method on a non-uniform high resolution orthogonal grid. The numerical predictions demonstrate a generic flow pattern for different turbulent heated jet discharges： the buoyant jets on each side of the diffuser first merge to form an essentially two-dimensional plume which bends back toward the diffuser centerline due to a low pressure cavity. In general, an under-pressure exists in the cavity until the plumes merge; the pressure increases to slightly positive afterwards. Two-dimensionality of the scalar and flow field is attained much later than the point of zero pressure. The position of merging point is governed by mainly four parameters - the discharge densimetfic Froude number, the port diameter and space, and the horizontal distance between alternating jet nozzles. A formula from numerical simulations is obtained through regression analysis and it is used to predict the position of plume merging point. The predicted temperature fields are comparable to previous experiments.展开更多
Different turbulence closures were used to predict the flow interaction between the wakes created by compressor outlet guide vanes(OGVs) and a downstream annular pre-diffuser.Two statistical turbulence models were tes...Different turbulence closures were used to predict the flow interaction between the wakes created by compressor outlet guide vanes(OGVs) and a downstream annular pre-diffuser.Two statistical turbulence models were tested based on the classical Reynolds-averaged Navier-Stokes(RANS) approach.Both high-Re and low-Re(Launder-Sharma) versions of the k-ε model were applied to a selected test problem for OGV wake/diffuser flows.The test problem was specifically chosen because experimentally determined inlet conditions and both profile and performance data were available to validate predictions.A preliminary study was also reported of the more advanced large eddy simulation(LES) approach.The LES sub-grid-scale(SGS) model was the basic Smagorinsky eddy viscosity assumption,with a Van-Driest damping function for improved capture of near-wall viscous behaviour.Comparison between the two RANS models showed little difference in terms of velocity contours at OGV trailing edge and diffuser exit.In terms of overall diffuser performance(static pressure recovery and total pressure loss coefficients),the high-Re model was shown to agree well with experimental data.The preliminary LES study indicates the highly unsteady character of the OGV wake flow,but requires improved treatment of inlet conditions.展开更多
The main fan diffuser in a coal mine is an energy-recycling equipment with a dynamic energy loss for the main fan. Engineering practices and related researches show that the body structures of three types of diffusers...The main fan diffuser in a coal mine is an energy-recycling equipment with a dynamic energy loss for the main fan. Engineering practices and related researches show that the body structures of three types of diffusers are irrational. To solve the problem, an energy-saving diffuser is designed on the basis of the velocity potential theory. Under conditions of inlet velocity from 7 m/s to 32 m/s, 7 condition experiments using the energy-saving diffuser of 2.31 AER （area-enlarging ratio） and 5 condi- tion experiments using the energy-saving diffuser of 2.00 AER were conducted. Through a comparative analysis of the experi- ments, the results show that the COP （coefficient of performance） of the energy-saving diffuser of 2.31 AER is better than that of the energy-saving diffuser of 2.00 AER.展开更多
The mixing of two or more components belongs to the category of the most common unit operations, both in technology and in nature. One particular version is homogenization(blending), the effectivity of which is strong...The mixing of two or more components belongs to the category of the most common unit operations, both in technology and in nature. One particular version is homogenization(blending), the effectivity of which is strongly related to the blending time. Among many differentiated individual solutions of mixing systems used in blenders, one should distinguish the class of agitators with diffusers. An analysis of the character of the velocity field during a blending chamber operation leads to the conclusion that it would be of avail to outfit a straight diffuser with different setups of elbows. In consequence, the vertical direction of the inflowing fluid stream would be changed into the horizontal direction of the outflowing stream, which should intensify the blending process. The concept has been verified experimentally, making use of the tracer methodology. The obtained results confirmed the theoretical conclusion that the blending time for the swirling-diffuser was shorter than for the classical straight one.展开更多
A turbulent separation-rcattachment flow in a two-dimensional asymmetrical curved-wall diffuser is studied by a two-dimensional laser doppler velocimeter.The turbulent boundary layer separates on the lower curved wall...A turbulent separation-rcattachment flow in a two-dimensional asymmetrical curved-wall diffuser is studied by a two-dimensional laser doppler velocimeter.The turbulent boundary layer separates on the lower curved wall under strong pressure gradient and then reattaches on a parallel channel.At the inlet of the diffuser,Reynolds number based on the diffuser height is 1.2×10~5 and the velocity is 25.2m/s.The re- sults of experiments are presented and analyzed in new defined streamline-aligned coordinates.The experiment shows that after Transitory Detachment Reynolds shear stress is negative in the near-wall backflow region. Their characteristics are approximately the same as in simple turbulent shear layers near the maximum Reynolds shear stress.A scale is formed using the maximum Reynolds shear stresses.It is found that a Reynolds shear stress similarity exists from separation to reattachment and the Schofield-Perry velocity law ex- ists in the forward shear flow.Both profiles are used in the experimental work that leads to the design of a new eddy-viscosity model.The length scale is taken from that developed by Schofield and Perry.The composite velocity scale is formed by the maximum Reynolds shear stress and the Schofield Perry velocity scale as well as the edge velocity of the boundary layer.The results of these experiments are presented in this paper展开更多
The stability of the flow in the vaneless diffuser of a centrifugal compressor is studied with the linear theory. The characteristics of direct and adjoint perturbation modes are investigated,and the receptivity of th...The stability of the flow in the vaneless diffuser of a centrifugal compressor is studied with the linear theory. The characteristics of direct and adjoint perturbation modes are investigated,and the receptivity of the instability mode to momentum forcing or mass injection is identified based on the adjoint modes. Analysis shows that the perturbation with the largest amplitude is located at the outlet of the vaneless diffuser, while the highest-receptivity region is located in the middle of the vaneless diffuser along the radial direction. The large difference between the direct and adjoint modes indicates that the instability mechanism cannot be identified from a study of either eigenmode separately. Therefore, the structural sensitivity analysis is adopted to study the feedback of the instability mode. The structural sensitivity of the eigenvalue which is proportional to the perturbation pressure and velocity is used to explain the mechanism of flow control for the vaneless diffuser.展开更多
An improved model to calculate the length of the mixing chamber of the ejector was proposed on the basis of the Fano flow model,and a method to optimize the structures of the mixing chamber and diffuser of the ejector...An improved model to calculate the length of the mixing chamber of the ejector was proposed on the basis of the Fano flow model,and a method to optimize the structures of the mixing chamber and diffuser of the ejector was put forward.The accuracy of the model was verified by comparing the theoretical results calculated using the model to experimental data reported in literature.Variations in the length of the mixing chamber L_(m) and length of the diffuser L_(d) with respect to variations in the outlet temperature of the ejector T_(c),outlet pressure of the ejector p_(c),and the expansion ratio of the pressure of the primary flow to that of the secondary flow p_(g)/p_(e) were investigated.Moreover,variations in L_(m) and L_(d) with respect to variations in the ratio of the diameter of the throat of the motive nozzle to the diameter of the mixing chamber d_(g0)/d_(c3) and ratio of the outlet diameter of the diffuser to the diameter of themixing chamber d_(c)/d_(c3) were investigated.The distribution of flow fields in the ejector was simulated.Increasing L_(m) and d_(c3) reduced T_(c) and p_(c).Moreover,reducing p_(g)/p_(e) or d_(g0)/d_(c3) reduced T_(c) and p_(c).The length of the mixed section L_(m2),which was determined on the basis of the Fano flow model,increased as pg increased and decreased as d_(c3) increased.The mixing length L_(m1),which was considered the primary flow expansion,showed the opposite trend with that of L_(m2).Moreover,Ld increased as p_(g)/p_(e) and d_(c)/d_(c3) increased.When the value of d_(c) was 1.8 to 2.0 times as high as that of dc3,the semi-cone angle of the diffuser ranged between 6°and 12°.At a constant dc/dc3,decreasing T_(c) and pc increased Ld.展开更多
文摘Size reduction of the gas turbines(GT)by reducing the inlet S-shaped diffuser length increases the powerto-weight ratio.It improves the techno-economic features of the GT by lesser fuel consumption.However,this Length reduction of a bare S-shaped diffuser to an aggressive S-shaped diffuser would risk flow separation and performance reduction of the diffuser and the air intake of the GT.The objective of this research is to propose and assess fitted energy promoters(EPs)to enhance the S-shaped diffuser performance by controlling and modifying the flow in the high bending zone of the diffuser.After experimental assessment,the work has been extended to cover more cases by numerical investigations on bare,bare aggressive,and aggressive with energy promoters S-shaped diffusers.Three types of EPs,namely co-rotating low-profile,co-rotating streamline sheet,and trapezoidal submerged EPs were tested with various combinations over a range of Reynolds numbers from 40,000 to 75,000.The respective S-shaped diffusers were simulated by computational fluid dynamics(CFD)using ANSYS software adopting a steady,3D,standard k-εturbulence model to acquire the details of the flow structure,which cannot be visualized in the experiment.The diffuser performance has been evaluated by the performance indicators of static pressure recovery coefficient,total pressure loss coefficient,and distortion coefficient(DC(45°)).The enhancements in the static pressure recovery of the S-shaped aggressive diffuser with energy promoters are 19.5%,22.2%,and 24.5%with EPs at planes 3,4 and 5,respectively,compared to the aggressive bare diffuser.In addition,the installation of the EPs resulted in a DC(45°)reduction at the outlet plane of the diffuser of about 43%at Re=40,000.The enhancements in the performance parameters confirm that aggravating the internal flow eliminates the flow separation and enhances the GT intake efficiency.
基金supported by the National Natural Science Foundation of China(No.52375274)the Zhejiang Provincial Natural Science Foundation of China(No.LD21E050003)+1 种基金the Key R&D Program of Zhejiang Province(No.2023C01229)the Central Government Fund for Regional Science and Technology Development of China(No.2023ZY1033).
文摘The thermocline energy storage tank(TEST)serves as a crucial component in thermal energy storage systems,utilizing the working fluid that enters through a diffuser to store and harness energy.However,the conventional double-plate radial diffuser is ill-suited for a single-medium TEST’s full tank storage due to its unidirectional fluid inflow.There has been a notable lack of optimization analysis of diffusers.Two innovative tubular diffuser designs with reduced cross-sectional areas have been introduced:the annular-arranged diffuser(AAD)and the cross-arranged diffuser(CAD).To elucidate the impact of diffuser designs on energy storage efficiency,a 3D transient computational fluid dynamics(CFD)model was established to simulate a thermocline formation under two diffuser types.The model was validated against experimental data.Results showed that the thermocline of AAD was 11.39%thinner than that of a traditional double-plate diffuser.In the process of charging and discharging,the time-varying thermocline and factors influencing thermocline thickness were analyzed.Results indicate that in the mixed dominant region,increased turbulent kinetic energy correlates with reduced thermocline thickness.Notably,the AAD’s stable thermocline was 4.23%and 5.41%thinner than the CAD’s during charging and discharging,respectively,making the AAD preferable for engineering applications.The effects of tube diameter and orifice opening angle on temperature stratification performance were also examined.The findings suggest that an inclined impact jet and large-diameter tubes are more conducive to temperature stratification.Moreover,an orifice diameter optimization method was developed,which can decrease the thermocline by 6.78%.
文摘The dump diffuser is an important component in advanced annular combustor, and its performance affects greatly the fluid field and pressure loss of the combustor. This paper presents the characteristics of the total pressure loss. Experiments and numerical simulations, keeping the inlet March number of prediffuser constant ( Ma =0 20), are carried out to obtain the regularity of the total pressure loss. It varies with the relative dump gap ( δ =1 2～3 0)by changing the position of prediffuser and combustor liner, respectively. Research shows that there exists the minimum total pressure loss ( σ *=1 6%～1 75%) when relative dump gap δ is about 1 8.
文摘In order to improve the performances of an 11 cm-diameter turbine engine,this article suggests to substitute a new-style micro diffuser redesigned based on a new concept for the traditional diffuser having poor performances. The new diffuser comprises integral blades and splitters,which are taken for a series of ducts in designing. This article investigates the effects of the cross-section area distribution along the flow path on the redesigned diffuser＇s performances. Having furnished with the new diffuser in place of the original vaned one,the 11 cm-diameter prototype engine is tested on the rig for its performances. CFD and experiments have shown that the improved diffuser with the unchanged original size has gained excellent performance parameters of pressure coefficient over 0.65 and total pressure recovery coefficient over 0.9. Equipped with the redesigned micro diffuser,the engine increases the thrust by 11% and decreases the specific fuel consumption by 9%.
基金supported by the National Natural Science Foundation of China (No.51276108)
文摘To expand the stable operating range of compressors, understanding the mechanism of flow instability at low flow rates is necessary. In this paper, the mechanism of stall and surge in a centrifugal compressor with a variable vaned diffuser is experimentally investigated, where the diffuser blade setting angle can be adjusted. Many dynamic pressure transducers are mounted on the casing surface of the compressor. From the design condition to surge, dynamic pressure data is recorded throughout the gradual process. According to the signal developing status, the typical modes of compressor instability are defined in detail, such as stall, mild surge, and deep surge. A relatively high-frequency stall wave originates in the impeller and propagates to the diffuser, and finally stimulates a deep surge in the compressor. The compressor behavior during surge differs at different diffuser vane angles. When the diffuser vane angle is adjusted, both the unstable form and the core factor affecting the overall machine stability change. A specific indicator is proposed to measure the instability of each component in a compressor, which can be used to determine the best region for stability extension technologies, such as a holed casing treatment, in different compressor applications.
文摘The paper presents analysis of the performance and the internal flow behaviour in the vaned diffuser of a radial flow pump using PIV(particle image velocimetry)and pressure probe traverses.PIV measurements have already been performed at middle height inside one diffuser channel passage for a given speed of rotation and various mass flow rates.These results have been already presented in several previous communications.New experiments have been performed using a three-hole pressure probe traverses from hub to shroud diffuser width at different radial locations between the two diffuser geometrical throats.Numerical simulations are also realized with the commercial codes Star CCM+7.02.011 and CFX.Frozen rotor and fully unsteady calculations of the whole pump have been performed.Comparisons between numerical results,previous experimental PIV results and new probe traverses one's are presented and discussed for one mass flow rate.In this respect,a first attempt to take into account fluid leakages between the rotating and fixed part of the pump has been checked since it may affects the real flow structure inside the diffuser.
文摘The influence of diffuser parameters, including the riser spacing, port number in a riser, injection angle, port arrangement, etc., on the surface initial dilution is experimentally investigated. The relative density difference between the effluent and the sea water in the model is the same as that in the prototype, and the effect of the cross current is simulated by an inverse model technique. Based on the result analysis, the arrangement with more ports in a riser and larger riser spacing is suggested to save construction cost. The relationship between the Reynolds number based on the port diameter and velocity, and the surface initial dilution is also explored, and the critical Reynolds number is proposed.
基金Supported by the National Natural Science Foundation of China(50974060)the Scientific Research Fund of Hunan Provincial Education Department(09CY014)the Doctoral Fund of Hunan University of Science and Technology
文摘Based on the boundary condition of field engineering, numerical simulations of28 conditions of existing diffusers of 3 structure types were investigated by ComputationalFluid Dynamics software package, and there were the problems of larger structure resistanceand lower diffusing efficiency of these diffusers by analysis of CFD results.Thestructure outlines of the energy-saving diffuser were constructed by the application ofstream function and potential function superimposing.On the basis of numerical simulationsof energy-saving diffusers of 5 area-enlarging ratios, structural resistances and diffusingefficiencies of 5 energy-saving diffusers were comparatively analyzed, and therange from 2.00 to 2.31 of the rational area-enlarging ratio of energy-saving diffusers wasderived.The optimization area-enlarging ratio of the energy-saving diffuser was presently2.28 through comparable analysis.From the above, the results show that the coefficient ofperformance of the energy-saving diffuser is better than 3 existing diffusers.
基金Projects(59375211,10771178,10676031) supported by the National Natural Science Foundation of ChinaProject(07A068) supported by the Key Project of Hunan Education CommissionProject(2005CB321702) supported by the National Key Basic Research Program of China
文摘The internal turbulent flow in conical diffuser is a very complicated adverse pressure gradient flow.DLR k-ε turbulence model was adopted to study it.The every terms of the Laplace operator in DLR k-ε turbulence model and pressure Poisson equation were discretized by upwind difference scheme.A new full implicit difference scheme of 5-point was constructed by using finite volume method and finite difference method.A large sparse matrix with five diagonals was formed and was stored by three arrays of one dimension in a compressed mode.General iterative methods do not work wel1 with large sparse matrix.With algebraic multigrid method(AMG),linear algebraic system of equations was solved and the precision was set at 10-6.The computation results were compared with the experimental results.The results show that the computation results have a good agreement with the experiment data.The precision of computational results and numerical simulation efficiency are greatly improved.
文摘Laboratory experiments were conducted to investigate the mixture of wastewater discharged from a submerged multiport diffuser in the Nantong sea-area. The process was then simulated with a three-dimensional numerical model. The plane or line patch was used to impose the discharge momentum flux in the near field. A comparison of model simulation with laboratory experiments shows that the proposed model can be used to simulate the shapes of pollution plumes, the distributions of excess concentration, and the velocity induced by a coflowing diffuser in proximity to a shoreline boundary. From the numerical simulation and laboratory experiments, it is recommended that the multiport diffuser be placed in a hydrodynamically active sea-area.
文摘Centrifugal compressors with parallel-wall and contracting wall vaneless diffuser are designed by using centrifugal compressor computer-aided integrated design system. The internal flow fields of the compressor are calculated by solving three-dimensional Navier-Stokes equation. Four aspects are investigated and calculation results show that the total efficiencies and total pressure ratios of the compressor with contracting wall vandess diffuser is higher than that of the compressor with parallel-wall. The jet and wake don＇t mix rapidly inside vandess diffuser. The outlet blade lean angle doesn＇t affect the compressor performance. The greater the mass flow rate through impeller, the more uneven the velocity distribution at impeller outlet is.
文摘The wind turbine with a flanged-diffuser shroud—so called “wind-lens turbine”—is developed as one of high performance wind turbines by Ohya et al. In this paper, the wind turbine performance is investigated for both steady and unsteady winds. The compact-type wind lens turbine shows higher efficiency than the only rotor wind turbine. Also, the flow structure around the compact-type wind turbine is made clear by CFD and PIV in steady wind. Furthermore, the performances of the only rotor and the compact-type wind-lens turbines for unsteady wind are experimentally and numerically investigated. Experimental and numerical results are presented to demonstrate the dependence of frequency of the harmonic oscillating velocity wind on power coefficient. Consequently, the compact-type wind-lens turbine show better performance than the only rotor one in sinusoidally oscillating velocity wind. Furthermore, the numerical estimation can predict the power coefficient in the oscillating flows to an accuracy of 94% to 102%. In addition, the dependence of the turbine performance on turbulent intensity and vortex scale of natural fluctuating wind is presented.
文摘The plume interaction above an alternating diffuser in stagnant water is studied with 3D Reynolds-averaged NavierStokes equations （RANS） combined with a buoyancy-extended κ-ε model. The steady three-dimensional turbulent flow and temperature fields are computed by use of the finite volume method on a non-uniform high resolution orthogonal grid. The numerical predictions demonstrate a generic flow pattern for different turbulent heated jet discharges： the buoyant jets on each side of the diffuser first merge to form an essentially two-dimensional plume which bends back toward the diffuser centerline due to a low pressure cavity. In general, an under-pressure exists in the cavity until the plumes merge; the pressure increases to slightly positive afterwards. Two-dimensionality of the scalar and flow field is attained much later than the point of zero pressure. The position of merging point is governed by mainly four parameters - the discharge densimetfic Froude number, the port diameter and space, and the horizontal distance between alternating jet nozzles. A formula from numerical simulations is obtained through regression analysis and it is used to predict the position of plume merging point. The predicted temperature fields are comparable to previous experiments.
文摘Different turbulence closures were used to predict the flow interaction between the wakes created by compressor outlet guide vanes(OGVs) and a downstream annular pre-diffuser.Two statistical turbulence models were tested based on the classical Reynolds-averaged Navier-Stokes(RANS) approach.Both high-Re and low-Re(Launder-Sharma) versions of the k-ε model were applied to a selected test problem for OGV wake/diffuser flows.The test problem was specifically chosen because experimentally determined inlet conditions and both profile and performance data were available to validate predictions.A preliminary study was also reported of the more advanced large eddy simulation(LES) approach.The LES sub-grid-scale(SGS) model was the basic Smagorinsky eddy viscosity assumption,with a Van-Driest damping function for improved capture of near-wall viscous behaviour.Comparison between the two RANS models showed little difference in terms of velocity contours at OGV trailing edge and diffuser exit.In terms of overall diffuser performance(static pressure recovery and total pressure loss coefficients),the high-Re model was shown to agree well with experimental data.The preliminary LES study indicates the highly unsteady character of the OGV wake flow,but requires improved treatment of inlet conditions.
文摘The main fan diffuser in a coal mine is an energy-recycling equipment with a dynamic energy loss for the main fan. Engineering practices and related researches show that the body structures of three types of diffusers are irrational. To solve the problem, an energy-saving diffuser is designed on the basis of the velocity potential theory. Under conditions of inlet velocity from 7 m/s to 32 m/s, 7 condition experiments using the energy-saving diffuser of 2.31 AER （area-enlarging ratio） and 5 condi- tion experiments using the energy-saving diffuser of 2.00 AER were conducted. Through a comparative analysis of the experi- ments, the results show that the COP （coefficient of performance） of the energy-saving diffuser of 2.31 AER is better than that of the energy-saving diffuser of 2.00 AER.
文摘The mixing of two or more components belongs to the category of the most common unit operations, both in technology and in nature. One particular version is homogenization(blending), the effectivity of which is strongly related to the blending time. Among many differentiated individual solutions of mixing systems used in blenders, one should distinguish the class of agitators with diffusers. An analysis of the character of the velocity field during a blending chamber operation leads to the conclusion that it would be of avail to outfit a straight diffuser with different setups of elbows. In consequence, the vertical direction of the inflowing fluid stream would be changed into the horizontal direction of the outflowing stream, which should intensify the blending process. The concept has been verified experimentally, making use of the tracer methodology. The obtained results confirmed the theoretical conclusion that the blending time for the swirling-diffuser was shorter than for the classical straight one.
文摘A turbulent separation-rcattachment flow in a two-dimensional asymmetrical curved-wall diffuser is studied by a two-dimensional laser doppler velocimeter.The turbulent boundary layer separates on the lower curved wall under strong pressure gradient and then reattaches on a parallel channel.At the inlet of the diffuser,Reynolds number based on the diffuser height is 1.2×10~5 and the velocity is 25.2m/s.The re- sults of experiments are presented and analyzed in new defined streamline-aligned coordinates.The experiment shows that after Transitory Detachment Reynolds shear stress is negative in the near-wall backflow region. Their characteristics are approximately the same as in simple turbulent shear layers near the maximum Reynolds shear stress.A scale is formed using the maximum Reynolds shear stresses.It is found that a Reynolds shear stress similarity exists from separation to reattachment and the Schofield-Perry velocity law ex- ists in the forward shear flow.Both profiles are used in the experimental work that leads to the design of a new eddy-viscosity model.The length scale is taken from that developed by Schofield and Perry.The composite velocity scale is formed by the maximum Reynolds shear stress and the Schofield Perry velocity scale as well as the edge velocity of the boundary layer.The results of these experiments are presented in this paper
文摘The stability of the flow in the vaneless diffuser of a centrifugal compressor is studied with the linear theory. The characteristics of direct and adjoint perturbation modes are investigated,and the receptivity of the instability mode to momentum forcing or mass injection is identified based on the adjoint modes. Analysis shows that the perturbation with the largest amplitude is located at the outlet of the vaneless diffuser, while the highest-receptivity region is located in the middle of the vaneless diffuser along the radial direction. The large difference between the direct and adjoint modes indicates that the instability mechanism cannot be identified from a study of either eigenmode separately. Therefore, the structural sensitivity analysis is adopted to study the feedback of the instability mode. The structural sensitivity of the eigenvalue which is proportional to the perturbation pressure and velocity is used to explain the mechanism of flow control for the vaneless diffuser.
文摘An improved model to calculate the length of the mixing chamber of the ejector was proposed on the basis of the Fano flow model,and a method to optimize the structures of the mixing chamber and diffuser of the ejector was put forward.The accuracy of the model was verified by comparing the theoretical results calculated using the model to experimental data reported in literature.Variations in the length of the mixing chamber L_(m) and length of the diffuser L_(d) with respect to variations in the outlet temperature of the ejector T_(c),outlet pressure of the ejector p_(c),and the expansion ratio of the pressure of the primary flow to that of the secondary flow p_(g)/p_(e) were investigated.Moreover,variations in L_(m) and L_(d) with respect to variations in the ratio of the diameter of the throat of the motive nozzle to the diameter of the mixing chamber d_(g0)/d_(c3) and ratio of the outlet diameter of the diffuser to the diameter of themixing chamber d_(c)/d_(c3) were investigated.The distribution of flow fields in the ejector was simulated.Increasing L_(m) and d_(c3) reduced T_(c) and p_(c).Moreover,reducing p_(g)/p_(e) or d_(g0)/d_(c3) reduced T_(c) and p_(c).The length of the mixed section L_(m2),which was determined on the basis of the Fano flow model,increased as pg increased and decreased as d_(c3) increased.The mixing length L_(m1),which was considered the primary flow expansion,showed the opposite trend with that of L_(m2).Moreover,Ld increased as p_(g)/p_(e) and d_(c)/d_(c3) increased.When the value of d_(c) was 1.8 to 2.0 times as high as that of dc3,the semi-cone angle of the diffuser ranged between 6°and 12°.At a constant dc/dc3,decreasing T_(c) and pc increased Ld.
