Improving the thermal conductivity(TC)of diamond–metal composites has always been a significant challenge in the field of thermal management.In this paper,diamond/Al composites are systematically studied,and the infl...Improving the thermal conductivity(TC)of diamond–metal composites has always been a significant challenge in the field of thermal management.In this paper,diamond/Al composites are systematically studied,and the influence of the holding time(10–120 min)on interface structure and TC is discussed.The results of this research show that longterm thermal diffusion sintering can achieve dense interfacial bonding in diamond/Al composites,enhancing their TC.Diamond/Al composites with 50 vol%of 900μm diamond attain the highest TC value of 888.73 W·m^(-1)·K^(-1)under sintering conditions of 650?C,50 MPa,and 120 min—nearly 92%of the theoretical value predicted by the Maxwell model.This study establishes that high TC can be achieved through long-term thermal diffusion alone,without the need for complex diamond surface coating or substrate alloying.展开更多
The interfacial thermal conductance （ITC） and thermal conductivity （TC） of diamond/Al composites with various coatings were theoretically studied and discussed. A series of predictions and numerical analyses were ...The interfacial thermal conductance （ITC） and thermal conductivity （TC） of diamond/Al composites with various coatings were theoretically studied and discussed. A series of predictions and numerical analyses were performed to investigate the effect of thickness, sound velocity, and other parameters of coating layers on the ITC and TC. It is found that both the ITC and TC decline with increasing coating thickness, especially for the coatings with relatively low thermal conductivity. Nevertheless, if the coating thickness is close to zero, or quite a small value, the ITC and TC are mainly determined by the constants of the coating material. Under this condition, coatings such as Ni, TiC, Mo 2 C, SiC, and Si can significantly improve the ITC and TC of diamond/Al composites. By contrast, coatings like Ag will exert the negative effect. Taking the optimization of interfacial bonding into account, conductive carbides such as TiC or Mo 2 C with low thickness can be the most suitable coatings for diamond/Al composites.展开更多
The microstructural evolution and performance of diamond/Al composites during thermal cycling has rarely been investigated.In the present work,the thermal stability of diamond/Al composites during thermal cycling for ...The microstructural evolution and performance of diamond/Al composites during thermal cycling has rarely been investigated.In the present work,the thermal stability of diamond/Al composites during thermal cycling for up to 200 cycles was explored.Specifically,the thermal conductivity(λ)of the composites was measured and scanning electron microscopy of specific areas in the same samples was carried out to achieve quasi-in situ observations.The interface between the(100)plane of diamond and the Al matrix was well bonded with a zigzag morphology and abundant needle-like Al4C3 phases.By contrast,the interface between the(111)plane of diamond and the Al matrix showed weak bonding and debonded during thermal cycling.The debonding length increased rapidly over the first 100 thermal cycles and then increased slowly in the following 100 cycles.Theλof the diamond/Al composites decreased abruptly over the initial 20 cycles,increased afterward,and then decreased monotonously once more with increasing number of thermal cycles.Decreases in theλof the Al matrix and the corresponding stress concentration at the diamond/Al interface caused by thermal mismatch,rather than interfacial debonding,may be the main factors influencing the decrease inλof the diamond/Al composites,especially in the initial stages of thermal cycling.展开更多
A titanium coating fabricated via vacuum vapor deposition for diamond/Al composites was used to improve the interfacial bonding strength between diamond particles and Al matrix,and the Ti coated diamond particles rein...A titanium coating fabricated via vacuum vapor deposition for diamond/Al composites was used to improve the interfacial bonding strength between diamond particles and Al matrix,and the Ti coated diamond particles reinforced Al matrix composites were prepared by gas pressure infiltration for electronic packaging.The surface structure of the Ti coated diamond particles was investigated by XRD and SEM.The interfacial characteristics and fracture surfaces were observed by SEM and EDS.The coefficient of thermal expansion(CTE)of 50%(volume fraction)Ti coated diamond particles reinforced Al matrix composites was measured. The Ti coating on diamond before infiltration consists of inner TiC layer and outer TiO2 layer,and the inner TiC layer is very stable and cannot be removed during infiltration process.Fractographs of the composites illustrate that aluminum matrix fracture is the dominant fracture mechanism,and the stepped breakage of a diamond particle indicates strong interfacial bonding between the Ti coated diamond particles and the Al matrix.The measured low CTEs(5.07×10-6-9.27×10 -6K -1)of the composites also show the strong interfacial bonding between the Ti coated diamond particles and the Al matrix.展开更多
A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The resu...A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.展开更多
This study investigates the fabrication and characterization of Al alloy matrix composites reinforced with graphene oxide(GO) using accumulative roll bonding(ARB).The annealed Al 6061 sheets were processed through 5-p...This study investigates the fabrication and characterization of Al alloy matrix composites reinforced with graphene oxide(GO) using accumulative roll bonding(ARB).The annealed Al 6061 sheets were processed through 5-pass ARB with GO reinforcement applied during the initial passes.Scanning electron microscopy revealed effective mitigation of GO agglomeration and improved interface bonding due to microscale material mixing.Raman spectroscopy confirmed the strong interaction between GO and the Al alloy matrix,as evidenced by the increased D band intensities and enhanced 2D band symmetry.Mechanical testing indicated an approximately 338.37% increase in yield strength(YS)and 86.42%improvement in hardness for the ARB-processed(ARBed)Al 6061/GO composite(0.2wt%)compared with annealed Al 6061 and an approximately 14.15%increase in YS and 17.23%improvement in hardness for the ARBedAl/GO composite(0.2wt%)compared with unreinforced ARBed Al 6061 specimens after five passes.X-ray diffraction analysis indicated an increased dislocation density,corroborating the observed enhancements in mechanical properties.Fracture surface analysis revealed reduced elongation with deep dimples,highlighting the tradeoff between strength and ductility.These results demonstrate the effectiveness of ARB for integrating GO into the Al 6061 matrix to improve the mechanical performance and interfacial bonding and underscore its potential for advanced composite materials.展开更多
SiCp-reinforced 6092Al composites with volume fractions of 25%and 60%were prepared using a powder metallurgy method.Their friction and wear characteristics were analyzed using a reciprocating friction and wear testing...SiCp-reinforced 6092Al composites with volume fractions of 25%and 60%were prepared using a powder metallurgy method.Their friction and wear characteristics were analyzed using a reciprocating friction and wear testing machine under loads of 20 to 50 N against YG6 cemented carbide.The experimental results show that the friction coefficients of all samples increase with increasing load.The 25vol%composite exhibits the lowest friction coefficient(0.1669-0.2716),while the 60vol%composite exhibits the highest(0.3237-0.3990),with the 6092 aluminum alloy falling between the two.The wear volume and specific wear rate also increase with load,but the composites with a higher Si C content demonstrate smaller increments,with the 60vol%composite exhibiting superior wear resistance.Under a 30 N load,the wear scars of the 60vol%composite show a significant increase in the contents of elements such as C,Co,W,and O,indicating more severe wear of the counterpart material.Scanning electron microscopy(SEM)reveals wear mechanisms including adhesive wear,two-body sliding and three-body rolling wear of particles,and delamination.展开更多
Inorganic materials can solve transportable and on-site hydrolytic hydrogen generation issues.CaH_(2)/(Al/Si)composites are preferable due to their notable chemical properties.However,these composites require pretreat...Inorganic materials can solve transportable and on-site hydrolytic hydrogen generation issues.CaH_(2)/(Al/Si)composites are preferable due to their notable chemical properties.However,these composites require pretreatments,an inert environment,and long hours of physical ball milling for high homogeneity and synergistic effects.CaH_(2)also inhibits the hydrolysis reaction by forming its products on the Al/Si surface,which hinders the direct utilization of composites.This work represents the first investigation of NaH-CaH_(2)(Al/Si)fuel composites,which greatly overcome these limitations and can be directly used for on-site hydrogen generation and proton exchange membrane(PEM)fuel cells.The NaH-CaH_(2)(Al/Si)fuel composites were prepared by using a straightforward mixing method with variable composition ratios,showing high H_(2)yield and fuel cell(FC)performance.NaH addition provides the bridge effect,which opens up a new way to enable efficient hydrolysis and greatly enhances the hydrolysis activity of CaH_(2)/(Al/Si)composites.The novel fuel composites(NaH-CaH_(2)/Al)have extraordinary FC performance and a 0.42 W/cm2 peak power density greater than commercial hydrogen generators.It provides high H_(2)yield 84.4%for NaH-CaH_(2)/Al and 82%for NaH-CaH_(2)/Si compared to NaOH-CaH_(2)(Al/Si),NaCl-CaH_(2)(Al/Si),and KCl-CaH_(2)(Al/Si)composites.The NaH bridge effect hinders the direct water contact and stops the formation of Ca(OH)2 around Al/Si,which provides adequate pathways for the CaH_(2)(Al/Si)hydrolysis.The impressive capabilities of novel fuel composites are anticipated to offer practical uses in fuel cells,automobile applications,and portable/on-board H_(2)generation.展开更多
High-volume fraction silicon particle-reinforced aluminium matrix composites(Si/Al)are increasingly applied in aerospace,radar communications,and large-scale integrated circuits because of their superior thermal condu...High-volume fraction silicon particle-reinforced aluminium matrix composites(Si/Al)are increasingly applied in aerospace,radar communications,and large-scale integrated circuits because of their superior thermal conductivity,wear resistance,and low thermal expansion coefficient.However,the abrasive and adhesive wear caused by the hard silicon reinforcement and the ductile aluminium matrix leads to significant tool wear,decreased machining efficiency,and compromised surface quality.This study combines theoretical analysis and cutting experiments to investigate polycrystalline diamond(PCD)tool wear during milling of 70 vol%Si/Al composite.A key contribution of this work is the development of a tool wear model that incorporates reinforcement particle characteristics,treating them as ellipsoidal structures,which enhances the accuracy of predicting abrasive and adhesive wear mechanisms.The model is based on abrasive and adhesive wear mechanisms,and can analyze the interaction between silicon particles,aluminium matrix,and tool components,thus providing deeper insights into PCD tool wear processes.Experimental validation of the model shows a good agreement with the results,with a mean deviation of approximately 10%.The findings on the tool wear mechanism reveal that,as tool wear progresses,the proportion of abrasive wear increases from 40%in the running-in stage to 75%in the rapid wear stage,while adhesive wear decreases.The optimal machining parameters of 120 m·min^(–1) cutting speed(v_(c))and 0.04 mm·z^(–1) feed rate(f_(z)),result in tool life of 33 min and surface roughness(S_(a))of 2.2μm.The study uncovers the variation patterns of abrasive and adhesive wear during the tool wear process,and the proposed model offers a robust framework for predicting tool wear during the machining of high-volume fraction Si/Al composites.The research findings also offer key insights for optimizing tool selection and machining parameters,advancing both the theoretical understanding and practical application of PCD tool wear.展开更多
The thermophysical properties of the SiC /Al composites mixed with diamond（SiC-Dia/Al） were studied through theoretical calculation and experiments. The thermal conductivity and the thermal expansion coefficient of ...The thermophysical properties of the SiC /Al composites mixed with diamond（SiC-Dia/Al） were studied through theoretical calculation and experiments. The thermal conductivity and the thermal expansion coefficient of the SiC-Dia/Al were calculated by differential effective medium（DEM） theoretical model and extended Turner model, respectively. The microstructure of the SiC-Dia/Al shows that the combination between SiC particles and Al is close, while that between diamond particles and Al is not close. The experimental results of the thermophysical properties of the SiC-Dia/Al are consistent with the calculated ones. The calculation results show that when the volume ratio of the diamond particles to the SiC particles is 3：7, the thermal conductivity and the thermal expansion coefficient can be improved by 39% and 30% compared to SiC/Al composites, respectively. In other words, by adding a small amount of diamond particles, the thermophysical properties of the composites can be improved effectively, while the cost increases little.展开更多
50%diamond particle （5μm） reinforced 2024 aluminum matrix （diamond/2024 Al） composites were prepared by pressure infiltration method. Diamond particles were distributed uniformly without any particle clustering, ...50%diamond particle （5μm） reinforced 2024 aluminum matrix （diamond/2024 Al） composites were prepared by pressure infiltration method. Diamond particles were distributed uniformly without any particle clustering, and no apparent porosities or significant casting defects were observed in the composites. The diamond-Al interfaces of as-cast and annealed diamond/2024 Al composites were clean, smooth and free from interfacial reaction product. However, a large number of Al2Cu precipitates were found at diamond-Al interface after aging treatment. Moreover, needle-shaped Al2MgCu precipitates in Al matrix were observed after aging treatment. The coefficient of thermal expansion （CTE） of diamond/2024 Al composites was about 8.5×10-6 °C-1 between 20 and 100 °C, which was compatible with that with chip materials. Annealing treatment showed little effect on thermal expansion behavior, and aging treatment could further decrease the CTE of the composites. The thermal conductivity of obtained diamond/2024 Al composites was about 100 W/（m？K）, and it was slightly increased after annealing while decreased after aging treatment.展开更多
Because of the challenge of compounding lightweight,high-strength Ti/Al alloys due to their considerable disparity in properties,Al 6063 as intermediate layer was proposed to fabricate TC4/Al 6063/Al 7075 three-layer ...Because of the challenge of compounding lightweight,high-strength Ti/Al alloys due to their considerable disparity in properties,Al 6063 as intermediate layer was proposed to fabricate TC4/Al 6063/Al 7075 three-layer composite plate by explosive welding.The microscopic properties of each bonding interface were elucidated through field emission scanning electron microscope and electron backscattered diffraction(EBSD).A methodology combining finite element method-smoothed particle hydrodynamics(FEM-SPH)and molecular dynamics(MD)was proposed for the analysis of the forming and evolution characteristics of explosive welding interfaces at multi-scale.The results demonstrate that the bonding interface morphologies of TC4/Al 6063 and Al 6063/Al 7075 exhibit a flat and wavy configuration,without discernible defects or cracks.The phenomenon of grain refinement is observed in the vicinity of the two bonding interfaces.Furthermore,the degree of plastic deformation of TC4 and Al 7075 is more pronounced than that of Al 6063 in the intermediate layer.The interface morphology characteristics obtained by FEM-SPH simulation exhibit a high degree of similarity to the experimental results.MD simulations reveal that the diffusion of interfacial elements predominantly occurs during the unloading phase,and the simulated thickness of interfacial diffusion aligns well with experimental outcomes.The introduction of intermediate layer in the explosive welding process can effectively produce high-quality titanium/aluminum alloy composite plates.Furthermore,this approach offers a multi-scale simulation strategy for the study of explosive welding bonding interfaces.展开更多
The aluminum(Al)/steel transition joints used in ships are processed from composite plates,and their mechanical properties have a significant impact on the safety of ships.In this paper,the Al/steel composite plate wa...The aluminum(Al)/steel transition joints used in ships are processed from composite plates,and their mechanical properties have a significant impact on the safety of ships.In this paper,the Al/steel composite plate was prepared using rolling,with 5083 aluminum plate as the cladding plate,Q235 steel plate as the substrate,and TA1 titanium(Ti)plate and DT4 pure iron(Fe)plate as the intermediate layers.The heterothermic billet was prepared through induction heating by the magnetic effects of the steel plate and the pure Fe plate,and then the Al/steel composite plate was obtained by rolling.The impacts of post-rolling cooling process on the microstructure and properties of the Al/Ti/pure Fe/steel composite plate were studied.The results manifested that the pure Fe/steel interface had a good composite effect.With the increase in the cooling rate,the bonding strength of the Al/Ti interface was raised,and that of the Ti/Fe interface was increased first and then decreased.When the oil cooling process was adopted,the Al/Ti/pure Fe/steel composite plate exhibited the highest comprehensive performance.The shear strength of the Al/Ti interface and the Ti/Fe interface was 102 MPa and 186 MPa,respectively.The plastic fracture was determined as the mode of interface fracture.展开更多
Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The tech...Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The techniques of FESEM/EDS,grazing incident beam X-ray diffraction(GIXRD),and electrochemical methods of potentiodynamic polarization and electrochemical impedance spectroscopy(EIS)were used to characterize the coatings.The results revealed that the coatings produced using the bipolar waveform exhibited lower porosity and higher thickness than those produced using the unipolar one.The corrosion performance of the specimens’cut edge was investigated using EIS after 1,8,and 12 h of immersion in a 3.5 wt.%NaCl solution.It was observed that the coating produced using the bipolar waveform demonstrated the highest corrosion resistance after 12 h of immersion,with an estimated corrosion resistance of 5.64 kΩ·cm^(2),which was approximately 3 times higher than that of the unipolar coating.Notably,no signs of galvanic corrosion were observed in the LMCs,and only minor corrosion attacks were observed on the magnesium layer in some areas.展开更多
The Mg−Al composite rods of aluminum core-reinforced magnesium alloy were prepared by the extrusion−shear(ES)process,and the microstructure,deformation mechanism,and mechanical properties of the Mg−Al composite rods w...The Mg−Al composite rods of aluminum core-reinforced magnesium alloy were prepared by the extrusion−shear(ES)process,and the microstructure,deformation mechanism,and mechanical properties of the Mg−Al composite rods were investigated at different extrusion temperatures and shear stresses.The experimental results show that the proportion of dynamic recrystallization(DRX)and texture for Al and Mg alloys are controlled by the combination of temperature and shear stress.The texture type of the Al alloys exhibits slight variations at different temperatures.With the increase of temperature,the DRX behavior of Mg alloy shifts from discontinuous DRX(DDRX),continuous DRX(CDRX),and twin-induced DRX(TDRX)dominant to CDRX,the dislocation density in Mg alloy grains decreases significantly,and the average value of Schmid factor(SF)of the basalslip system increases.In particular,partial grains exhibit a distinct dominant slip system at 390℃.The hardness and thickness of the bonding layer,as well as the yield strength and elongation of the Mg alloy,reach their maximum at 360℃as a result of the intricate influence of the combined temperature and shear stress.展开更多
Non-isothermal aging(NIA)treatments have presented significant advantages in improving the comprehensive performance and aging hardening efficiency of the 7000 series aluminum alloys,but there is no attention paid to ...Non-isothermal aging(NIA)treatments have presented significant advantages in improving the comprehensive performance and aging hardening efficiency of the 7000 series aluminum alloys,but there is no attention paid to their composites.This study takes a linear heating aging process as an example to reveal the precipitation behaviors of a 15 vol.%SiC/7085Al composite as well as its impact on mechanical properties using differential scanning calorimetry,transmission electron microscopy,small-angle neutron scattering,hardness measurements,and tensile testing.The results indicated the formation of GP(Ⅰ,Ⅱ)zones,η’andηprecipitates in sequence,leading to the hardness and strength initially increasing and then decreasing with rising NIA temperatures.The maximums were reached at 183℃,corresponding to the appearance ofη’precipitates in large quantities.Owing to the rapid temperature rise during the NIA process,the precipitates entered the coarsening and redissolution stage before they were entirely formed,resulting in reduced peak strength compared to the T6 treatment.The composite exhibited a more significant reduction in strength than the 7085Al alloy because:(i)the annihilation of vacancies suppressed the formation of GPII zones,thereby weakening their transition toη’precipitates;(ii)quenching dislocations promoted the coarsening of precipitates.An improved NIA process,incorporating both heating and cooling aging treatments,was effectively designed with the assistance of in-situ SANS technology to address this issue,which allows for achieving strength comparable to that after the T6 treatment with only 15%of the aging time consumption.This research fills the gap in investigating the NIA precipitation behaviors of aluminum matrix composites,providing guidance for the formulation of NIA schedules.展开更多
Cu/Al composite plates were fabricated using rolling and underwater explosive welding techniques,separately,to compare their interfacial microstructures and mechanical performance.Interface morphology,grain orientatio...Cu/Al composite plates were fabricated using rolling and underwater explosive welding techniques,separately,to compare their interfacial microstructures and mechanical performance.Interface morphology,grain orientation,grain boundary characteristics,and phase distribution were analyzed through optical microscope,scanning electron microscope,and electron backscattered diffractometer.Mechanical properties were assessed using tensile shear tests,90°bending tests,and hardness measurements.Vickers hardness and nanoindentation test results further provided information on the hardness distributions.Results indicate that the diffusion layer in rolled Cu/Al composites is relatively fragile,while that produced by underwater explosive welding features a diffusion layer of approximately 18μm in thickness,which is metallurgically bonded through atomic diffusion.The tensile shear strength of these composites ranges from 64.45 MPa to 70.84 MPa,and in the 90°three-point bending test,the underwater-explosive-welded samples exhibit superior flexural performance.This study elucidates the effects of different manufacturing methods on the interfacial properties and mechanical performance of Cu/Al composites,offering essential insights for the selection of manufacturing methods and applications.展开更多
AZ31/Al/Ta composites were prepared using the vacuum hot compression bonding(VHCB)method.The effect of hot compressing temperature on the interface microstructure evolution,phase constitution,and shear strength at the...AZ31/Al/Ta composites were prepared using the vacuum hot compression bonding(VHCB)method.The effect of hot compressing temperature on the interface microstructure evolution,phase constitution,and shear strength at the interface was investigated.Moreover,the interface bonding mechanisms of the AZ31/Al/Ta composites during the VHCB process were explored.The results demonstrate that as the VHCB temperature increases,the phase composition of the interface between Mg and Al changes from the Mg-Al brittle intermetallic compounds(Al_(12)Mg_(17)and Al_(3)Mg_(2))to the Al-Mg solid solution.Meanwhile,the width of the Al/Ta interface diffusion layer at 450℃increases compared to that at 400℃.The shear strengths are 24 and 46 MPa at 400 and 450℃,respectively.The interfacial bonding mechanism of AZ31/Al/Ta composites involves the coexistence of diffusion and mechanical meshing.Avoiding the formation of brittle phases at the interface can significantly improve interfacial bonding strength.展开更多
Cu-based and Cu-alloy-based diamond composites were made by high-pressure-high-temperature （HPHT） sintering with the aim of maximizing the thermal conductivity of the composites. Improvements in interfacial bonding ...Cu-based and Cu-alloy-based diamond composites were made by high-pressure-high-temperature （HPHT） sintering with the aim of maximizing the thermal conductivity of the composites. Improvements in interfacial bonding strength and thermo-physical properties of the composites were achieved using an atomized copper alloy with minor additions of Co, Cr, 13, and Ti. The thermal conductivity （TC） oh- mined exhibited as high as 688 W.m-1.K-1, but also as low as 325 W.m-1.K-l. A large variation in TC can be rationalized by the discrepancy of diamond-matrix interfacial bonding. It was found from fractography that preferential bonding between diamond and the Cu-alloy matrix occurred only on the diamond {100} faces. EDS analysis and Raman spectra suggested that selective interfacial bonding may be attributed to amorphous carbon increasing the wettability between diamond and the Cu-alloy matrix. Amorphous carbon was found to significantly affect the TC of the composite by interface modification.展开更多
The thermal conductivity of diamond hybrid SiC/Cu,diamond/Cu and SiC/Cu composite were calculated by using the extended differential effective medium (DEM) theoretical model in this paper.The effects of the particle v...The thermal conductivity of diamond hybrid SiC/Cu,diamond/Cu and SiC/Cu composite were calculated by using the extended differential effective medium (DEM) theoretical model in this paper.The effects of the particle volume fraction,the particle size and the volume ratio of the diamond particles to the total particles on the thermal conductivity of the composite were studied.The DEM theoretical calculation results show that,for the diamond hybrid SiC/Cu composite,when the particle volume fraction is above 46% and the volume ratio of the diamond particles to the SiC particles is above 13:12,the thermal conductivity of the composite can reach 500 W·m-1·K-1.The thermal conduc-tivity of the composite has little change when the particle size is above 200μm.The experimental results show that Ti can improve the wettability of the SiC and Cu.The thermal conductivity of the diamond hybrid SiCTi/Cu is almost two times better than that of the diamond hybrid SiC/Cu.It is feasible to predict the thermal conductivity of the composite by DEM theoretical model.展开更多
基金Project supported by the National Natural Science Foundation of China(Grant Nos.12274372 and 12274373)the Major Science and Technology Projects of Henan Province(Grant No.231100230300)。
文摘Improving the thermal conductivity(TC)of diamond–metal composites has always been a significant challenge in the field of thermal management.In this paper,diamond/Al composites are systematically studied,and the influence of the holding time(10–120 min)on interface structure and TC is discussed.The results of this research show that longterm thermal diffusion sintering can achieve dense interfacial bonding in diamond/Al composites,enhancing their TC.Diamond/Al composites with 50 vol%of 900μm diamond attain the highest TC value of 888.73 W·m^(-1)·K^(-1)under sintering conditions of 650?C,50 MPa,and 120 min—nearly 92%of the theoretical value predicted by the Maxwell model.This study establishes that high TC can be achieved through long-term thermal diffusion alone,without the need for complex diamond surface coating or substrate alloying.
文摘The interfacial thermal conductance （ITC） and thermal conductivity （TC） of diamond/Al composites with various coatings were theoretically studied and discussed. A series of predictions and numerical analyses were performed to investigate the effect of thickness, sound velocity, and other parameters of coating layers on the ITC and TC. It is found that both the ITC and TC decline with increasing coating thickness, especially for the coatings with relatively low thermal conductivity. Nevertheless, if the coating thickness is close to zero, or quite a small value, the ITC and TC are mainly determined by the constants of the coating material. Under this condition, coatings such as Ni, TiC, Mo 2 C, SiC, and Si can significantly improve the ITC and TC of diamond/Al composites. By contrast, coatings like Ag will exert the negative effect. Taking the optimization of interfacial bonding into account, conductive carbides such as TiC or Mo 2 C with low thickness can be the most suitable coatings for diamond/Al composites.
基金financially supported by the National Natural Science Foundation of China(Nos.1871072,51871073,52171136,51771063,61604086,and U1637201)the China Postdoctoral Science Foundation(Nos.2016M590280 and 2017T100240)+1 种基金the Heilongjiang Postdoctoral Foundation(Nos.LBH-Z16075 and LBH-TZ2014)the Fundamental Research Funds for the Central Universities,China(Nos.HIT.NSRIF.20161 and HIT.MKSTISP.201615).
文摘The microstructural evolution and performance of diamond/Al composites during thermal cycling has rarely been investigated.In the present work,the thermal stability of diamond/Al composites during thermal cycling for up to 200 cycles was explored.Specifically,the thermal conductivity(λ)of the composites was measured and scanning electron microscopy of specific areas in the same samples was carried out to achieve quasi-in situ observations.The interface between the(100)plane of diamond and the Al matrix was well bonded with a zigzag morphology and abundant needle-like Al4C3 phases.By contrast,the interface between the(111)plane of diamond and the Al matrix showed weak bonding and debonded during thermal cycling.The debonding length increased rapidly over the first 100 thermal cycles and then increased slowly in the following 100 cycles.Theλof the diamond/Al composites decreased abruptly over the initial 20 cycles,increased afterward,and then decreased monotonously once more with increasing number of thermal cycles.Decreases in theλof the Al matrix and the corresponding stress concentration at the diamond/Al interface caused by thermal mismatch,rather than interfacial debonding,may be the main factors influencing the decrease inλof the diamond/Al composites,especially in the initial stages of thermal cycling.
基金Project(60776019)supported by the National Natural Science Foundation of China
文摘A titanium coating fabricated via vacuum vapor deposition for diamond/Al composites was used to improve the interfacial bonding strength between diamond particles and Al matrix,and the Ti coated diamond particles reinforced Al matrix composites were prepared by gas pressure infiltration for electronic packaging.The surface structure of the Ti coated diamond particles was investigated by XRD and SEM.The interfacial characteristics and fracture surfaces were observed by SEM and EDS.The coefficient of thermal expansion(CTE)of 50%(volume fraction)Ti coated diamond particles reinforced Al matrix composites was measured. The Ti coating on diamond before infiltration consists of inner TiC layer and outer TiO2 layer,and the inner TiC layer is very stable and cannot be removed during infiltration process.Fractographs of the composites illustrate that aluminum matrix fracture is the dominant fracture mechanism,and the stepped breakage of a diamond particle indicates strong interfacial bonding between the Ti coated diamond particles and the Al matrix.The measured low CTEs(5.07×10-6-9.27×10 -6K -1)of the composites also show the strong interfacial bonding between the Ti coated diamond particles and the Al matrix.
基金supported by Guangdong Major Project of Basic and Applied Basic Research, China (No. 2020B0301030006)Fundamental Research Funds for the Central Universities, China (No. SWU-XDJH202313)+1 种基金Chongqing Postdoctoral Science Foundation Funded Project, China (No. 2112012728014435)the Chongqing Postgraduate Research and Innovation Project, China (No. CYS23197)。
文摘A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.
文摘This study investigates the fabrication and characterization of Al alloy matrix composites reinforced with graphene oxide(GO) using accumulative roll bonding(ARB).The annealed Al 6061 sheets were processed through 5-pass ARB with GO reinforcement applied during the initial passes.Scanning electron microscopy revealed effective mitigation of GO agglomeration and improved interface bonding due to microscale material mixing.Raman spectroscopy confirmed the strong interaction between GO and the Al alloy matrix,as evidenced by the increased D band intensities and enhanced 2D band symmetry.Mechanical testing indicated an approximately 338.37% increase in yield strength(YS)and 86.42%improvement in hardness for the ARB-processed(ARBed)Al 6061/GO composite(0.2wt%)compared with annealed Al 6061 and an approximately 14.15%increase in YS and 17.23%improvement in hardness for the ARBedAl/GO composite(0.2wt%)compared with unreinforced ARBed Al 6061 specimens after five passes.X-ray diffraction analysis indicated an increased dislocation density,corroborating the observed enhancements in mechanical properties.Fracture surface analysis revealed reduced elongation with deep dimples,highlighting the tradeoff between strength and ductility.These results demonstrate the effectiveness of ARB for integrating GO into the Al 6061 matrix to improve the mechanical performance and interfacial bonding and underscore its potential for advanced composite materials.
基金Funded by the Provincial Talent Project of Gansu Province(No.2025QNGR18)the Natural Science Foundation of Gansu Province(No.23JRRA1647)+2 种基金the"Qizhi"Talent Cultivation Project of Lanzhou Institute of Technology(No.2025QZ-02)the Education Science and Technology Innovation Project of Gansu Province(No.2025A-229)the Lanzhou Science and Technology Development Guidance Plan Project(No.2024-9-307)。
文摘SiCp-reinforced 6092Al composites with volume fractions of 25%and 60%were prepared using a powder metallurgy method.Their friction and wear characteristics were analyzed using a reciprocating friction and wear testing machine under loads of 20 to 50 N against YG6 cemented carbide.The experimental results show that the friction coefficients of all samples increase with increasing load.The 25vol%composite exhibits the lowest friction coefficient(0.1669-0.2716),while the 60vol%composite exhibits the highest(0.3237-0.3990),with the 6092 aluminum alloy falling between the two.The wear volume and specific wear rate also increase with load,but the composites with a higher Si C content demonstrate smaller increments,with the 60vol%composite exhibiting superior wear resistance.Under a 30 N load,the wear scars of the 60vol%composite show a significant increase in the contents of elements such as C,Co,W,and O,indicating more severe wear of the counterpart material.Scanning electron microscopy(SEM)reveals wear mechanisms including adhesive wear,two-body sliding and three-body rolling wear of particles,and delamination.
基金financial support granted by the National Natural Science Foundation of China (No. 22402225)the Gusu Innovation and Entrepreneurship Leading Talent Plan(No. ZXL2023193)+2 种基金the Sinano Talents Plan (No. 2022000175)the Guangdong Basic and Applied Basic Research Foundation (No.2023A1515111133)the ANSO Scholarship for Young Talents
文摘Inorganic materials can solve transportable and on-site hydrolytic hydrogen generation issues.CaH_(2)/(Al/Si)composites are preferable due to their notable chemical properties.However,these composites require pretreatments,an inert environment,and long hours of physical ball milling for high homogeneity and synergistic effects.CaH_(2)also inhibits the hydrolysis reaction by forming its products on the Al/Si surface,which hinders the direct utilization of composites.This work represents the first investigation of NaH-CaH_(2)(Al/Si)fuel composites,which greatly overcome these limitations and can be directly used for on-site hydrogen generation and proton exchange membrane(PEM)fuel cells.The NaH-CaH_(2)(Al/Si)fuel composites were prepared by using a straightforward mixing method with variable composition ratios,showing high H_(2)yield and fuel cell(FC)performance.NaH addition provides the bridge effect,which opens up a new way to enable efficient hydrolysis and greatly enhances the hydrolysis activity of CaH_(2)/(Al/Si)composites.The novel fuel composites(NaH-CaH_(2)/Al)have extraordinary FC performance and a 0.42 W/cm2 peak power density greater than commercial hydrogen generators.It provides high H_(2)yield 84.4%for NaH-CaH_(2)/Al and 82%for NaH-CaH_(2)/Si compared to NaOH-CaH_(2)(Al/Si),NaCl-CaH_(2)(Al/Si),and KCl-CaH_(2)(Al/Si)composites.The NaH bridge effect hinders the direct water contact and stops the formation of Ca(OH)2 around Al/Si,which provides adequate pathways for the CaH_(2)(Al/Si)hydrolysis.The impressive capabilities of novel fuel composites are anticipated to offer practical uses in fuel cells,automobile applications,and portable/on-board H_(2)generation.
基金supported by the National Natural Science Foundation of China(Grant No.52075255)the Jiangsu Provincial Science and Technology Plan(Grant No.BZ2023005).
文摘High-volume fraction silicon particle-reinforced aluminium matrix composites(Si/Al)are increasingly applied in aerospace,radar communications,and large-scale integrated circuits because of their superior thermal conductivity,wear resistance,and low thermal expansion coefficient.However,the abrasive and adhesive wear caused by the hard silicon reinforcement and the ductile aluminium matrix leads to significant tool wear,decreased machining efficiency,and compromised surface quality.This study combines theoretical analysis and cutting experiments to investigate polycrystalline diamond(PCD)tool wear during milling of 70 vol%Si/Al composite.A key contribution of this work is the development of a tool wear model that incorporates reinforcement particle characteristics,treating them as ellipsoidal structures,which enhances the accuracy of predicting abrasive and adhesive wear mechanisms.The model is based on abrasive and adhesive wear mechanisms,and can analyze the interaction between silicon particles,aluminium matrix,and tool components,thus providing deeper insights into PCD tool wear processes.Experimental validation of the model shows a good agreement with the results,with a mean deviation of approximately 10%.The findings on the tool wear mechanism reveal that,as tool wear progresses,the proportion of abrasive wear increases from 40%in the running-in stage to 75%in the rapid wear stage,while adhesive wear decreases.The optimal machining parameters of 120 m·min^(–1) cutting speed(v_(c))and 0.04 mm·z^(–1) feed rate(f_(z)),result in tool life of 33 min and surface roughness(S_(a))of 2.2μm.The study uncovers the variation patterns of abrasive and adhesive wear during the tool wear process,and the proposed model offers a robust framework for predicting tool wear during the machining of high-volume fraction Si/Al composites.The research findings also offer key insights for optimizing tool selection and machining parameters,advancing both the theoretical understanding and practical application of PCD tool wear.
文摘The thermophysical properties of the SiC /Al composites mixed with diamond（SiC-Dia/Al） were studied through theoretical calculation and experiments. The thermal conductivity and the thermal expansion coefficient of the SiC-Dia/Al were calculated by differential effective medium（DEM） theoretical model and extended Turner model, respectively. The microstructure of the SiC-Dia/Al shows that the combination between SiC particles and Al is close, while that between diamond particles and Al is not close. The experimental results of the thermophysical properties of the SiC-Dia/Al are consistent with the calculated ones. The calculation results show that when the volume ratio of the diamond particles to the SiC particles is 3：7, the thermal conductivity and the thermal expansion coefficient can be improved by 39% and 30% compared to SiC/Al composites, respectively. In other words, by adding a small amount of diamond particles, the thermophysical properties of the composites can be improved effectively, while the cost increases little.
基金Project (AWJ-M13-15) supported by the Open Fund of State Key Laboratory of Advanced Welding and Joining,Harbin Institute of Technology,China
文摘50%diamond particle （5μm） reinforced 2024 aluminum matrix （diamond/2024 Al） composites were prepared by pressure infiltration method. Diamond particles were distributed uniformly without any particle clustering, and no apparent porosities or significant casting defects were observed in the composites. The diamond-Al interfaces of as-cast and annealed diamond/2024 Al composites were clean, smooth and free from interfacial reaction product. However, a large number of Al2Cu precipitates were found at diamond-Al interface after aging treatment. Moreover, needle-shaped Al2MgCu precipitates in Al matrix were observed after aging treatment. The coefficient of thermal expansion （CTE） of diamond/2024 Al composites was about 8.5×10-6 °C-1 between 20 and 100 °C, which was compatible with that with chip materials. Annealing treatment showed little effect on thermal expansion behavior, and aging treatment could further decrease the CTE of the composites. The thermal conductivity of obtained diamond/2024 Al composites was about 100 W/（m？K）, and it was slightly increased after annealing while decreased after aging treatment.
基金Opening Foundation of Key Laboratory of Explosive Energy Utilization and Control,Anhui Province(BP20240104)Graduate Innovation Program of China University of Mining and Technology(2024WLJCRCZL049)Postgraduate Research&Practice Innovation Program of Jiangsu Province(KYCX24_2701)。
文摘Because of the challenge of compounding lightweight,high-strength Ti/Al alloys due to their considerable disparity in properties,Al 6063 as intermediate layer was proposed to fabricate TC4/Al 6063/Al 7075 three-layer composite plate by explosive welding.The microscopic properties of each bonding interface were elucidated through field emission scanning electron microscope and electron backscattered diffraction(EBSD).A methodology combining finite element method-smoothed particle hydrodynamics(FEM-SPH)and molecular dynamics(MD)was proposed for the analysis of the forming and evolution characteristics of explosive welding interfaces at multi-scale.The results demonstrate that the bonding interface morphologies of TC4/Al 6063 and Al 6063/Al 7075 exhibit a flat and wavy configuration,without discernible defects or cracks.The phenomenon of grain refinement is observed in the vicinity of the two bonding interfaces.Furthermore,the degree of plastic deformation of TC4 and Al 7075 is more pronounced than that of Al 6063 in the intermediate layer.The interface morphology characteristics obtained by FEM-SPH simulation exhibit a high degree of similarity to the experimental results.MD simulations reveal that the diffusion of interfacial elements predominantly occurs during the unloading phase,and the simulated thickness of interfacial diffusion aligns well with experimental outcomes.The introduction of intermediate layer in the explosive welding process can effectively produce high-quality titanium/aluminum alloy composite plates.Furthermore,this approach offers a multi-scale simulation strategy for the study of explosive welding bonding interfaces.
基金Supported by Science Research Project of Hebei Education Department(Grant No.BJK2024138)Hebei Provincial Natural Science Foundation(Grant No.E2023203129)National Natural Science Foundation of China(Grant Nos.52004242,52075472).
文摘The aluminum(Al)/steel transition joints used in ships are processed from composite plates,and their mechanical properties have a significant impact on the safety of ships.In this paper,the Al/steel composite plate was prepared using rolling,with 5083 aluminum plate as the cladding plate,Q235 steel plate as the substrate,and TA1 titanium(Ti)plate and DT4 pure iron(Fe)plate as the intermediate layers.The heterothermic billet was prepared through induction heating by the magnetic effects of the steel plate and the pure Fe plate,and then the Al/steel composite plate was obtained by rolling.The impacts of post-rolling cooling process on the microstructure and properties of the Al/Ti/pure Fe/steel composite plate were studied.The results manifested that the pure Fe/steel interface had a good composite effect.With the increase in the cooling rate,the bonding strength of the Al/Ti interface was raised,and that of the Ti/Fe interface was increased first and then decreased.When the oil cooling process was adopted,the Al/Ti/pure Fe/steel composite plate exhibited the highest comprehensive performance.The shear strength of the Al/Ti interface and the Ti/Fe interface was 102 MPa and 186 MPa,respectively.The plastic fracture was determined as the mode of interface fracture.
文摘Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The techniques of FESEM/EDS,grazing incident beam X-ray diffraction(GIXRD),and electrochemical methods of potentiodynamic polarization and electrochemical impedance spectroscopy(EIS)were used to characterize the coatings.The results revealed that the coatings produced using the bipolar waveform exhibited lower porosity and higher thickness than those produced using the unipolar one.The corrosion performance of the specimens’cut edge was investigated using EIS after 1,8,and 12 h of immersion in a 3.5 wt.%NaCl solution.It was observed that the coating produced using the bipolar waveform demonstrated the highest corrosion resistance after 12 h of immersion,with an estimated corrosion resistance of 5.64 kΩ·cm^(2),which was approximately 3 times higher than that of the unipolar coating.Notably,no signs of galvanic corrosion were observed in the LMCs,and only minor corrosion attacks were observed on the magnesium layer in some areas.
基金supported by the general project of the National Natural Science Foundation of China(No.52071042)Chongqing Natural Science Foundation Project,China(Nos.CSTB2023NSCQ-MSX0079,cstc2021ycjh-bgzxm0148)Graduate Student Innovation Program of Chongqing University of Technology,China(No.gzlcx20232008).
文摘The Mg−Al composite rods of aluminum core-reinforced magnesium alloy were prepared by the extrusion−shear(ES)process,and the microstructure,deformation mechanism,and mechanical properties of the Mg−Al composite rods were investigated at different extrusion temperatures and shear stresses.The experimental results show that the proportion of dynamic recrystallization(DRX)and texture for Al and Mg alloys are controlled by the combination of temperature and shear stress.The texture type of the Al alloys exhibits slight variations at different temperatures.With the increase of temperature,the DRX behavior of Mg alloy shifts from discontinuous DRX(DDRX),continuous DRX(CDRX),and twin-induced DRX(TDRX)dominant to CDRX,the dislocation density in Mg alloy grains decreases significantly,and the average value of Schmid factor(SF)of the basalslip system increases.In particular,partial grains exhibit a distinct dominant slip system at 390℃.The hardness and thickness of the bonding layer,as well as the yield strength and elongation of the Mg alloy,reach their maximum at 360℃as a result of the intricate influence of the combined temperature and shear stress.
基金support of the Na-tional Key R&D Program of China(No.2021YFA1600700)the Na-tional Natural Science Foundation of China(grant Nos.U22A20114,52322106,52192595,and 52301200)+2 种基金the Project funded by China Postdoctoral Science Foundation(No.2023M733573)CSNS Con-sortium on High-performance Materials of Chinese Academy of Sciences(No.JZHKYPT-2021-01)the Natural Science Foun-dation of Liaoning Province(No.2023-BS-020)。
文摘Non-isothermal aging(NIA)treatments have presented significant advantages in improving the comprehensive performance and aging hardening efficiency of the 7000 series aluminum alloys,but there is no attention paid to their composites.This study takes a linear heating aging process as an example to reveal the precipitation behaviors of a 15 vol.%SiC/7085Al composite as well as its impact on mechanical properties using differential scanning calorimetry,transmission electron microscopy,small-angle neutron scattering,hardness measurements,and tensile testing.The results indicated the formation of GP(Ⅰ,Ⅱ)zones,η’andηprecipitates in sequence,leading to the hardness and strength initially increasing and then decreasing with rising NIA temperatures.The maximums were reached at 183℃,corresponding to the appearance ofη’precipitates in large quantities.Owing to the rapid temperature rise during the NIA process,the precipitates entered the coarsening and redissolution stage before they were entirely formed,resulting in reduced peak strength compared to the T6 treatment.The composite exhibited a more significant reduction in strength than the 7085Al alloy because:(i)the annihilation of vacancies suppressed the formation of GPII zones,thereby weakening their transition toη’precipitates;(ii)quenching dislocations promoted the coarsening of precipitates.An improved NIA process,incorporating both heating and cooling aging treatments,was effectively designed with the assistance of in-situ SANS technology to address this issue,which allows for achieving strength comparable to that after the T6 treatment with only 15%of the aging time consumption.This research fills the gap in investigating the NIA precipitation behaviors of aluminum matrix composites,providing guidance for the formulation of NIA schedules.
基金Anhui Province Key Research and Development Plan(2022a05020021)China Coal Science and Industry Group Chongqing Research Institute Independent Research and Development Project(2023YBXM58)。
文摘Cu/Al composite plates were fabricated using rolling and underwater explosive welding techniques,separately,to compare their interfacial microstructures and mechanical performance.Interface morphology,grain orientation,grain boundary characteristics,and phase distribution were analyzed through optical microscope,scanning electron microscope,and electron backscattered diffractometer.Mechanical properties were assessed using tensile shear tests,90°bending tests,and hardness measurements.Vickers hardness and nanoindentation test results further provided information on the hardness distributions.Results indicate that the diffusion layer in rolled Cu/Al composites is relatively fragile,while that produced by underwater explosive welding features a diffusion layer of approximately 18μm in thickness,which is metallurgically bonded through atomic diffusion.The tensile shear strength of these composites ranges from 64.45 MPa to 70.84 MPa,and in the 90°three-point bending test,the underwater-explosive-welded samples exhibit superior flexural performance.This study elucidates the effects of different manufacturing methods on the interfacial properties and mechanical performance of Cu/Al composites,offering essential insights for the selection of manufacturing methods and applications.
基金National Natural Science Foundation of China(52275308,52301146)Fundamental Research Funds for the Central Universities(2023JG007)Supported by Shi Changxu Innovation Center for Advanced Materials(SCXKFJJ202207)。
文摘AZ31/Al/Ta composites were prepared using the vacuum hot compression bonding(VHCB)method.The effect of hot compressing temperature on the interface microstructure evolution,phase constitution,and shear strength at the interface was investigated.Moreover,the interface bonding mechanisms of the AZ31/Al/Ta composites during the VHCB process were explored.The results demonstrate that as the VHCB temperature increases,the phase composition of the interface between Mg and Al changes from the Mg-Al brittle intermetallic compounds(Al_(12)Mg_(17)and Al_(3)Mg_(2))to the Al-Mg solid solution.Meanwhile,the width of the Al/Ta interface diffusion layer at 450℃increases compared to that at 400℃.The shear strengths are 24 and 46 MPa at 400 and 450℃,respectively.The interfacial bonding mechanism of AZ31/Al/Ta composites involves the coexistence of diffusion and mechanical meshing.Avoiding the formation of brittle phases at the interface can significantly improve interfacial bonding strength.
基金supported by the National Natural Science Foundation of China (No.50971020) National High-Tech Research and Development Program of China (No.2008AA03Z505)
文摘Cu-based and Cu-alloy-based diamond composites were made by high-pressure-high-temperature （HPHT） sintering with the aim of maximizing the thermal conductivity of the composites. Improvements in interfacial bonding strength and thermo-physical properties of the composites were achieved using an atomized copper alloy with minor additions of Co, Cr, 13, and Ti. The thermal conductivity （TC） oh- mined exhibited as high as 688 W.m-1.K-1, but also as low as 325 W.m-1.K-l. A large variation in TC can be rationalized by the discrepancy of diamond-matrix interfacial bonding. It was found from fractography that preferential bonding between diamond and the Cu-alloy matrix occurred only on the diamond {100} faces. EDS analysis and Raman spectra suggested that selective interfacial bonding may be attributed to amorphous carbon increasing the wettability between diamond and the Cu-alloy matrix. Amorphous carbon was found to significantly affect the TC of the composite by interface modification.
基金financially supported by High-Technology Research and Development Program of China (No.2008AA03Z505)
文摘The thermal conductivity of diamond hybrid SiC/Cu,diamond/Cu and SiC/Cu composite were calculated by using the extended differential effective medium (DEM) theoretical model in this paper.The effects of the particle volume fraction,the particle size and the volume ratio of the diamond particles to the total particles on the thermal conductivity of the composite were studied.The DEM theoretical calculation results show that,for the diamond hybrid SiC/Cu composite,when the particle volume fraction is above 46% and the volume ratio of the diamond particles to the SiC particles is above 13:12,the thermal conductivity of the composite can reach 500 W·m-1·K-1.The thermal conduc-tivity of the composite has little change when the particle size is above 200μm.The experimental results show that Ti can improve the wettability of the SiC and Cu.The thermal conductivity of the diamond hybrid SiCTi/Cu is almost two times better than that of the diamond hybrid SiC/Cu.It is feasible to predict the thermal conductivity of the composite by DEM theoretical model.
