This work experimentally examined the optimal proportioning of sludge curing agent for dewatered sludge curing on solidified sludge,two components sludge curing agent consisted of cement and slag,and three components ...This work experimentally examined the optimal proportioning of sludge curing agent for dewatered sludge curing on solidified sludge,two components sludge curing agent consisted of cement and slag,and three components consisted of cement,slag and inorganic salt. The results showed that,increasing of curing ages could increase unconfined compressive strength and reduce moisture content for solidified sludge. For the test of two components,the biggest unconfined compressive strength of the solidified sludge achieved to 543. 72 kPa and the minimum moisture content achieved to 3. 56% of 21 d. The optimum proportion of the sludge curing agent of two components is sludge: cement: slag = 1 ∶ 0. 05 ∶ 0. 2 which selected by Design-expert. It could rapidly increasing the unconfined compressive strength of solidified sludge when added three components sludge curing agent( sludge: cement: slag: MgSO4= 1 ∶ 0. 05 ∶ 0. 2 ∶ 0. 03) on sludge curing. The results showed that,curing ages of 7 d,the unconfined compressive strength could achieve to 126. 74 kPa,which was more than 11 times comparison with the solidified sludge curing by two components curing agent. Two or three components sludge curing agent all could stabilize the heavy metals on solidified sludge and the leaching of heavy metals was below the government standard,while the stability of the heavy metals was superior for three components sludge curing agent.展开更多
The effect of pre-treatment of dewatered sludge using different nitrite concentrations and p H for microbial fuel cell(MFC) application was investigated. The results show that the addition of nitrite was feasible to i...The effect of pre-treatment of dewatered sludge using different nitrite concentrations and p H for microbial fuel cell(MFC) application was investigated. The results show that the addition of nitrite was feasible to increase the solubilization rate of the sludge and may reduce mass transfer limitation at the anode. This helped the MFC to reach higher voltage and to generate more power. The higher free nitrous acid(FNA) concentration under the acidic condition helped to increase sludge solubilization. However, under an alkaline condition, during which the FNA concentration was relatively low, the solubilization of the sludge was higher. The highest voltage and power density produced was 390 mV and 153 mW/m^2, respectively, with the addition of nitrite at 100 mg-N/L and pH 9. Furthermore,it was found that elevated levels of FNA could inhibit electrogenic bacteria thus reducing power generation.展开更多
This study mainly focused on the occurrence of pharmaceutical and personal care products(PPCPs)in sewage dewatered sludge and their discharges through sludge disposal from wastewater treatment plants(WWTPs).The data w...This study mainly focused on the occurrence of pharmaceutical and personal care products(PPCPs)in sewage dewatered sludge and their discharges through sludge disposal from wastewater treatment plants(WWTPs).The data were obtained and calculated from seven PPCPs in dewatered sludge collected from 12WWTPs in two typical cities,Beijing and Shenzhen in China.Four of seven PPCPs,diclofenac acid,carbamazepine,mefenamic acid and N,N-diethyl-m-toluamide were detectable in dewatered sludge from Beijing and Shenzhen with concentration up to 4240,11,060,92 and 219μg/kg respectively.While,the other three compounds,trimethoprim,chloramphenicol and bezafibrate were not detected in collected samples from these two cities.The highest discharge of diclofenac acid and carbamazepine were 1023 g/d and 494 g/d respectively.In addition,the total discharge of these four detected PPCPs from each plant ranged from 5 to 1092 g/d in Beijing and 4e497 g/d in Shenzhen.Thus,PPCP discharge through sludge disposal cannot be neglected,and further research on transfer of PPCPs during sludge disposal onto agriculture land and influence of sludge application is required and essential.展开更多
This work investigates the influence of the type sludge on drainage, plant development, purification performances and biosolids quality. Drainage properties were measured through the frequency of clogging, the percent...This work investigates the influence of the type sludge on drainage, plant development, purification performances and biosolids quality. Drainage properties were measured through the frequency of clogging, the percentage of leachate recovered and the dryness of accumulated sludge. Plant development was measured through the density, the height and the stem diameter. Purification performance was evaluated from the reduction rate. Biosolids quality was measured after 3 months of maturation. The results show that the clogging frequencies were 9.5%;0% and 3.7%;the volume of leachate recovered was 42.2%;20.4% and 24.7% and, the dryness was 33.4%;61.1% and 52.4% for FS-ST, FS-STT and SS respectively. Plants densities were about, with densities 197.1, 171.3 and 178.3 plants/m2 in beds fed respectively with FS-ST, FS-STT and SS. Despite the high removal rates, the concentrations of pollutants in the leachates are above the Senegalese standard NS 05-061 for discharge into the environment. The biosolids are all mature with C/N and NH4+/NO3?ratios lower than 12 and 1 respectively. The biosolids are also rich in organic and mineral elements. The concentrations of Ascaris eggs are higher than the WHO recommendations. These biosolids should be stored for additional time or composted.展开更多
Surface watercourses are areas of very high ecological and heritage value. Macroinvertebrates are bioindicators of the health of aquatic ecosystems. The aim of this study was to assess the effects of dewatering and re...Surface watercourses are areas of very high ecological and heritage value. Macroinvertebrates are bioindicators of the health of aquatic ecosystems. The aim of this study was to assess the effects of dewatering and re-watering cycles on benthic macroinvertebrate (BMI) communities. Two data collections were carried out at two stations (Okpara 1 and Okpara 2) on the Okpara river before and after dewatering. Thus, 8 samples of benthic macroinvertebrates and 12 physico-chemical parameters (T°C, pH, Transparency, Depth, Conductivity, Dissolved Oxygen that were measured in situ, and BOD5, COD, NH<sub>4</sub><sup>+</sup>, NO<sub>3</sub><sup>-</sup>, NO<sub>2</sub><sup>-</sup> and PO<sub>4</sub><sup>3-</sup>) were assayed in the laboratory. Canonical Correspondence Analysis (CCA) was used to match physico-chemical data to MIB families. Shannon and Piélou diversity indices were used to determine the effects of dewatering on MIBs. The increase in temperature values of pH, BOD5, COD, NH4</sub>+</sup>, NO3</sub>-</sup>, NO2</sub>-</sup> and PO4</sub>3-</sup>, after re-watering indicates the effect of dewatering on the quality of Okpara aquatic ecosystems. The benthic macrofauna collected consisted of 62.42% insects, 0.65% crustaceans, 6.48% molluscs, 0.72% worms and 0.14% arachnids. Whereas after re-watering, 21.67% insects, 0% crustaceans, 0.22% molluscs, 7.56% worms and 0.29% arachnids were recorded. Insects, crustaceans and molluscs were more abundant before dewatering than after. This was revealed by low abundances and taxonomic richness, as well as low Shannon index values of samples collected after re-watering.展开更多
The carbonaceous adsorbent was prepared from mixtures of dewatered sludge and sawdust with enhanced ZnCl2 chemical activation.Characteristics of the adsorbent were studied using scanning electron microscope(SEM) ,Four...The carbonaceous adsorbent was prepared from mixtures of dewatered sludge and sawdust with enhanced ZnCl2 chemical activation.Characteristics of the adsorbent were studied using scanning electron microscope(SEM) ,Fourier transform infrared spectroscopy(FT-IR) ,and adsorption of nitrogen.The surface analysis showed that the carbonaceous adsorbent had good specific surface and porosity(394 m 2 ·g-1of BET surface,0.12 and 0.10 ml·g-1of microporous and mesoporous volume,respectively) .The oxygen functional groups such as OH,C O and C O were found on the surface by FTIR and XPS(X-ray photoelectron spectroscopy) .The adsorption of elemental mercury(Hg0) on the carbonaceous adsorbent was studied in a fixed bed reactor.The dynamic adsorption capacity of carbonaceous adsorbent increased with influent mercury concentration,from 23.6μg·g-1at 12.58μg·m-3to 87.9μg·g-1at 72.50μg·m-3,and decreased as the adsorption temperature increased,from 246 μg·g-1 at 25°C to 61.3μg·g-1 at 140°C,when dry nitrogen was used as the carrier gas.The carbonaceous adsorbent presented higher dynamic adsorption capacity than activated carbon,which was 81.2μg·g-1and 53.8μg·g-1respectively.The adsorption data were fitted to the Langmuir adsorption model.The physical and chemical adsorption were identified on the adsorbent.展开更多
[Objective]The aim was to research water retention of superabsorbent polymer （SAP） in sandy soils. [Method] With soils from an ancient course in the Yel ow River as materials, acrylate SAP was taken as water retenti...[Objective]The aim was to research water retention of superabsorbent polymer （SAP） in sandy soils. [Method] With soils from an ancient course in the Yel ow River as materials, acrylate SAP was taken as water retention materials to conduct the test. [Result] With 0.2%-0.4% SAP added, dewatering period of sandy soil extended after irrigation; the period of water retention quantity over 10% last for 42 d, which was significantly more than that of the control group in 16 d （saturated water reducing to 10%）; water retention effect proved better at the 2nd irrigation without soil stirring compared with the 1st irrigation. [Conclusion] The mixture of SAP with sandy soils promotes water retention in soils.展开更多
This research evaluated the use of sewage sludge and refuse incineration bottom ash to replace calcium sulfoaluminate cement （CSA） in making controlled low-strength material （CLSM）. Various properties of CLSM mixt...This research evaluated the use of sewage sludge and refuse incineration bottom ash to replace calcium sulfoaluminate cement （CSA） in making controlled low-strength material （CLSM）. Various properties of CLSM mixtures were characterized in terms of unconfined compressive strength, microstructure and leachability. It was found that the strength of tested CLSM mixtures ranged from 3.6 to 9.0 MPa, over the upper excavatable limit of 2.1 MPa. The micro-structural analysis revealed that sewage sludge and bottom ash were crystallochemically in- corporated within CLSM system_s by forming the needle-like ettringite （C3A＇3CS＇_H32） with exiguous tu.bers via the typical Pozzolanic Reaction, leading to a dense and low-porosity microst;＇ucture. Furthermore,-the toxicity characteristic leaching procedure evidenced that the cumulative leachable metals in the leachate were much below the regulatory thresholds. The potential for us!ng sewage sludge and bottom ash!n CLSM makin.g was thus confirmed.展开更多
[Objective] The technological parameter suitable for the dewatering of dredged sediment from Dianchi Lake was studied.[Method] By means of the treatment method of sewage sludge in sewage treatment plant,flocculants in...[Objective] The technological parameter suitable for the dewatering of dredged sediment from Dianchi Lake was studied.[Method] By means of the treatment method of sewage sludge in sewage treatment plant,flocculants including FeCl3,Al2(SO4)3 and PAM were taken as dewatering agents which were added in dredged sediment.[Result] The results showed that Al2(SO4)3 had better dewatering effect than FeCl3 and PAM,and the optimum dosing quantity of Al2(SO4)3 in dredged sediment was 170 mg/L,in addition,the water quality of supernatant met the first class B standard of GB18918-2002 and could be directly discharged to nature water without pollution.[Conclusion] The study could provide a simple and feasible way for the rapid dewatering of dredged sediment from Dianchi Lake,which would be convenient for the disposal and resource utilization of dredged sediment.展开更多
The slurry settling characteristics are the most important to design a thickener in process industries. In this work, the iron ore slurry from the screw classifier overflow was used for the settling study. It was obse...The slurry settling characteristics are the most important to design a thickener in process industries. In this work, the iron ore slurry from the screw classifier overflow was used for the settling study. It was observed that the original slurry exhibited a low settling velocity and a turbid supernatant during the settling process. Commercial flocculating agents with anionic, cationic, and nonionic characters were used to improve the settling behavior of suspensions, which were added into the slurry at different ranges of slurry pH values, respectively. The settling results show that the use of flocculants increase the settling rate by several times. Compared with the cationic and non-ionic flocculants, the anionic flocculant is more effective in enhancing the slurry settling rate. The small dose of the anionic flocculant is found to be more effective, but the other flocculants are less effective even at higher dosages. The simulation of an industrial thickener was carried out based on the laboratory settling data, and the appropriate design and selection parameters of the industrial thickener were estimated.展开更多
Enhancing sludge dewatering is of importance in reducing environmental burden and disposal costs.In this work, a cationic surfactant, cetyl trimethyl ammonium bromide(CTAB), was combined with Fenton’s reagent for slu...Enhancing sludge dewatering is of importance in reducing environmental burden and disposal costs.In this work, a cationic surfactant, cetyl trimethyl ammonium bromide(CTAB), was combined with Fenton’s reagent for sludge dewatering.Results show that the Fenton-CTAB conditioning significantly promotes the sludge dewatering.Using combined techniques of response surface methodology and uniform design, dosages of Fe2+, H2O2, and CTAB for water content response were optimized to be 89, 276, and 233 mg/g dry solids(DS),respectively.The water content of sludge decreased from 79.0% to 66.8% under the optimal conditions.Compared with cationic polyacrylamide, the Fenton-CTAB system exhibited superior sludge dewatering performance.To gain insights into the mechanisms involved in sludge dewatering, the effects of Fenton-CTAB conditioning on the composition of extracellular polymeric substances(EPS) and the morphology of the sludge flocs were investigated.The decomposition of EPS into some dissolved organics and the release of proteins in tightly bound EPS facilitated the conversion of bound water to free water and further reduced the water content of sludge cake.After conditioning, morphology of sludge showed aggregation.Overall, the enhanced sludge dewatering by Fenton-CTAB treatment provides an efficient way for management of sewage sludge.展开更多
A technology of ultrasonic-electric united desalting and dewatering of crude oil is studied. The ultrasonic setup is designed to form a standing-wave field, which is more efficient for agglomeration of water particles...A technology of ultrasonic-electric united desalting and dewatering of crude oil is studied. The ultrasonic setup is designed to form a standing-wave field, which is more efficient for agglomeration of water particles. The desalting and dewatering results of the ultrasonic-electric united process are compared with those of the electric process. For high salt-contenting crude oil （40-70 mg·L ^-1）, the salt content is still above 10.0 mg·L^-1 after crude oil has been treated by two-stage electric desalting process in refinery, which cannot meet the need of refinery. Ultrasonic-electric united process is a novel technology for treating the high salt-contenting oil. On the optimal operating conditions of the ultrasonic-electric united process, the salt content of crude oil can be reduced from 67 5 mg·L^-1 to 3.97 mg·L ^-1 by one-stage ultrasonic-electric united process, and the water content falls below 0.3% （by volume）. The results show that the ultrasonic-electric united process is more effective than the electric process in high salt-contenting oil desalting. This technology should be useful in the refinery process.展开更多
This paper reports the systematic investigation on the flocculation,sedimentation and consolidation characteristics of kaolinite using guar gum as a green flocculant.In-situ flocculation behavior of kaolinite at vario...This paper reports the systematic investigation on the flocculation,sedimentation and consolidation characteristics of kaolinite using guar gum as a green flocculant.In-situ flocculation behavior of kaolinite at various pH,guar gum dosages,and ionic strength were studied using a light scattering technique.The effect of these parameters on the settling rate,solid consolidation,and supernatant liquid clarity was recorded.The morphology of kaolinite and flocculated kaolinite aggregates were analyzed using FESEM.The morphology studies suggest that it is poorly crystalline with multiple steps on edge,broken edge;laminar with high aspect ratio and have rough basal surface.The complex irregularity on the basal surface and the presence of multiple steps in the edges,broken edges(hydroxyl groups)have facilitated the guar gum adsorption.The isoelectric point of kaolinite is pH 3.96.The pH,ionic strength and flocculant dosage have a significant effect on the kaolinite settling rate.The guar gum has exhibited excellent turbidity removal efficiency at pH 5.The turbidity removal is inefficient at pH 10.However,guar gum has shown high turbidity removal with 80%transmission at pH 10 in the presence of a KNO3 electrolyte.展开更多
Rapid flocculation and settlement(FS)of mine tailings is significant for the improvement and development of the filling process,whereas the settlement velocity(SV)of tailings in FS has been recognized as a key paramet...Rapid flocculation and settlement(FS)of mine tailings is significant for the improvement and development of the filling process,whereas the settlement velocity(SV)of tailings in FS has been recognized as a key parameter to evaluate the settlement effect.However,the influence of temperature on the SV and its mechanism have not been studied.FS experiments on tailings with various ambient temperatures were carried out.The SVs of tailings with a solid waste content of 10wt%and an anionic polyacrylamide content of 20 g·t^−1 were measured at different temperatures.The SV presented an“N”-shaped variation curve as the temperature changed from 5 to 40℃.The mechanism of these results can be explained from the perspective of the electric double-layer repulsive force,molecular dynamics,and the polymer flocculation principle,as revealed from the scanning electron microscopy of floc particles.The findings will be beneficial in the design of tailings dewatering processes and save costs in the production of cemented paste backfill.展开更多
The filtration and dewatering of fine clean coal not only ensure industrial water recycle in coal washing plant,but also reduce the moisture of coal product in order to meet the requirements of combustion or coking in...The filtration and dewatering of fine clean coal not only ensure industrial water recycle in coal washing plant,but also reduce the moisture of coal product in order to meet the requirements of combustion or coking industry.Fine clean coal is mainly composed by organic matter,and the property difference of different organic matter determines the filtration and dewatering behavior.In this investigation,vitrinite and inertinite were separated from a clean bituminous coal,and the comparative filtration and dewatering behavior of vitrinite and inertinite were conducted.The results showed that inertinite has lower dewatering rate and higher filter cake moisture than vitrinite.The analysis of filter cake structure showed that inertinite particle is easier to be broken into small particles due to the difference of mechanical properties,thus forming more compact filter cake than vitrinite.The analysis of particle surface properties showed that vitrinite is more hydrophobic than inertinite,which makes water easier drained from filter cake.The simulation study showed that the structure of inertinite is more porous than that of vitrinite,and the interaction between inertinite and water is stronger than that between vitrinite and water.This study provides a theoretical basis for improving coal dewatering by selectively improving coal maceral hydrophobicity.展开更多
Ultraviolet(UV)assisted zero-valent iron(ZVI)-activated sodium persulfate(PDS)oxidation(UV-ZVI-PDS)was used to treat waste activated sludge(WAS)in this study.The dewaterability performance and mechanism of WAS dewater...Ultraviolet(UV)assisted zero-valent iron(ZVI)-activated sodium persulfate(PDS)oxidation(UV-ZVI-PDS)was used to treat waste activated sludge(WAS)in this study.The dewaterability performance and mechanism of WAS dewatering were analyzed.The results showed that UV-ZVI-PDS can obtain better sludge dewatering performance in a wide pH range(2.0-8.0).When the molar ratio of ZVI/PDS was 0.6,UV was 254nm,PDS dosage was 200 mg/g TS(total solid),pH was 6.54,reaction time was 20 min,the CST(capillary suction time)and SRF(specific resistance to filtration)were decreased by 64.0%and 78.2%,respectively.The molar ratio of ZVI/PDS used in this paper is much lower than that of literatures,and the contents of total Fe and Fe^(2+) in sludge supernatant remained at a low level,as 3.7 mg/L and 0.0 mg/L.The analysis of extracellular polymeric substances(EPS),scanning electron microscope(SEM)and particle size distribution showed that the EPS could be effectively destroyed by UV-ZVI-PDS,the sludge flocs broken down into smaller particles,cracks and holes appeared,and then the bound water was released.At the same time,the highly hydrophilic tightly bound-EPS(TB-EPS)were converted into loosely bound EPS(LB-EPS)and soluble EPS(S-EPS).During sludge pretreated by UV-ZVI-PDS,positively charged ions,such as Fe^(2+),Fe^(3+) and H^(+),produced in the reaction system could reduce the electronegativity of sludge surface,promote sludge particles aggregation,and then enhanced the sludge dewaterability.展开更多
A key step in sludge treatment is sludge dewatering. However, activated sludge is generally very difficult to be dewatered. Sludge dewatering performance is largely affected by the sludge moisture distribution. Sludge...A key step in sludge treatment is sludge dewatering. However, activated sludge is generally very difficult to be dewatered. Sludge dewatering performance is largely affected by the sludge moisture distribution. Sludge disintegration can destroy the sludge structure and cell wall, so as change the sludge floc structure and moisture distribution, thus affecting the dewatering performance of sludge. In this article, the disintegration methods were ultrasound treatment, K2 Fe O4oxidation and KMn O4 oxidation. The degree of disintegration（DDCOD）, sludge moisture distribution and the final water content of sludge cake after centrifuging were measured. Results showed that three disintegration methods were all effective, and K2 Fe O4oxidation was more efficient than KMn O4 oxidation. The content of free water increased obviously with K2 Fe O4and KMn O4 oxidations, while it decreased with ultrasound treatment. The changes of free water and interstitial water were in the opposite trend. The content of bounding water decreased with K2 Fe O4oxidation, and increased slightly with KMn O4 oxidation, while it increased obviously with ultrasound treatment. The water content of sludge cake after centrifuging decreased with K2 Fe O4oxidation, and did not changed with KMn O4 oxidation, but increased obviously with ultrasound treatment. In summary, ultrasound treatment deteriorated the sludge dewaterability, while K2 Fe O4and KMn O4 oxidation improved the sludge dewaterability.展开更多
When pumping is conducted in confined aquifer inside excavation pit(waterproof curtain),the direction of the groundwater seepage outside the excavation changes from horizontal to vertical owing to the existence of the...When pumping is conducted in confined aquifer inside excavation pit(waterproof curtain),the direction of the groundwater seepage outside the excavation changes from horizontal to vertical owing to the existence of the curtain barrier.There is no analytical calculation method for the groundwater head distribution induced by dewatering inside excavation.This paper first analyses the mechanism of the blocking effects from a close barrier in confined aquifer.Then,a simple equation based on analytical solution is proposed to calculate groundwater heads inside and outside of the excavation pit with waterproof curtain(hereafter refer to close barrier)in a confined aquifer.The distribution of groundwater head is derived according to two conditions:(i)pumping with a constant water head,and(ii)pumping with a constant flow rate.The proposed calculation equation is verified by both numerical simulation and experimental results.The comparisons demonstrate that the proposed model can be applied in engineering practice of excavation.展开更多
基金Sponsored by the Technology Research Projects of Harbin Science and Technology Bureau(Grant No.2010AA4CS024)the Fundamental Research Funds for the Central Universities(Grant No.HIT.NSRIF.201192)+1 种基金the National Natural Science Key Foundation of China(Grant No.51206036)the State Key Laboratory of Urban Water Resource and Environment,Harbin Institute of Technology(Grant No.2013DX04)
文摘This work experimentally examined the optimal proportioning of sludge curing agent for dewatered sludge curing on solidified sludge,two components sludge curing agent consisted of cement and slag,and three components consisted of cement,slag and inorganic salt. The results showed that,increasing of curing ages could increase unconfined compressive strength and reduce moisture content for solidified sludge. For the test of two components,the biggest unconfined compressive strength of the solidified sludge achieved to 543. 72 kPa and the minimum moisture content achieved to 3. 56% of 21 d. The optimum proportion of the sludge curing agent of two components is sludge: cement: slag = 1 ∶ 0. 05 ∶ 0. 2 which selected by Design-expert. It could rapidly increasing the unconfined compressive strength of solidified sludge when added three components sludge curing agent( sludge: cement: slag: MgSO4= 1 ∶ 0. 05 ∶ 0. 2 ∶ 0. 03) on sludge curing. The results showed that,curing ages of 7 d,the unconfined compressive strength could achieve to 126. 74 kPa,which was more than 11 times comparison with the solidified sludge curing by two components curing agent. Two or three components sludge curing agent all could stabilize the heavy metals on solidified sludge and the leaching of heavy metals was below the government standard,while the stability of the heavy metals was superior for three components sludge curing agent.
基金funded by Universiti Sains Malaysia via Research University Grant(RUI)scheme(No.1001/PJKIMIA/814267)Bridging Grant scheme(No.304.PJKIMIA.6316120)the Ministry of Higher Education Malaysia for providing scholarship(MyBrain)
文摘The effect of pre-treatment of dewatered sludge using different nitrite concentrations and p H for microbial fuel cell(MFC) application was investigated. The results show that the addition of nitrite was feasible to increase the solubilization rate of the sludge and may reduce mass transfer limitation at the anode. This helped the MFC to reach higher voltage and to generate more power. The higher free nitrous acid(FNA) concentration under the acidic condition helped to increase sludge solubilization. However, under an alkaline condition, during which the FNA concentration was relatively low, the solubilization of the sludge was higher. The highest voltage and power density produced was 390 mV and 153 mW/m^2, respectively, with the addition of nitrite at 100 mg-N/L and pH 9. Furthermore,it was found that elevated levels of FNA could inhibit electrogenic bacteria thus reducing power generation.
基金supported by Tsinghua University e Veolia Environment Joint Research Center for Advanced Environment Technology and the Program for Changjiang Scholars and Innovative Research Team in University(IRT1261).
文摘This study mainly focused on the occurrence of pharmaceutical and personal care products(PPCPs)in sewage dewatered sludge and their discharges through sludge disposal from wastewater treatment plants(WWTPs).The data were obtained and calculated from seven PPCPs in dewatered sludge collected from 12WWTPs in two typical cities,Beijing and Shenzhen in China.Four of seven PPCPs,diclofenac acid,carbamazepine,mefenamic acid and N,N-diethyl-m-toluamide were detectable in dewatered sludge from Beijing and Shenzhen with concentration up to 4240,11,060,92 and 219μg/kg respectively.While,the other three compounds,trimethoprim,chloramphenicol and bezafibrate were not detected in collected samples from these two cities.The highest discharge of diclofenac acid and carbamazepine were 1023 g/d and 494 g/d respectively.In addition,the total discharge of these four detected PPCPs from each plant ranged from 5 to 1092 g/d in Beijing and 4e497 g/d in Shenzhen.Thus,PPCP discharge through sludge disposal cannot be neglected,and further research on transfer of PPCPs during sludge disposal onto agriculture land and influence of sludge application is required and essential.
文摘This work investigates the influence of the type sludge on drainage, plant development, purification performances and biosolids quality. Drainage properties were measured through the frequency of clogging, the percentage of leachate recovered and the dryness of accumulated sludge. Plant development was measured through the density, the height and the stem diameter. Purification performance was evaluated from the reduction rate. Biosolids quality was measured after 3 months of maturation. The results show that the clogging frequencies were 9.5%;0% and 3.7%;the volume of leachate recovered was 42.2%;20.4% and 24.7% and, the dryness was 33.4%;61.1% and 52.4% for FS-ST, FS-STT and SS respectively. Plants densities were about, with densities 197.1, 171.3 and 178.3 plants/m2 in beds fed respectively with FS-ST, FS-STT and SS. Despite the high removal rates, the concentrations of pollutants in the leachates are above the Senegalese standard NS 05-061 for discharge into the environment. The biosolids are all mature with C/N and NH4+/NO3?ratios lower than 12 and 1 respectively. The biosolids are also rich in organic and mineral elements. The concentrations of Ascaris eggs are higher than the WHO recommendations. These biosolids should be stored for additional time or composted.
文摘Surface watercourses are areas of very high ecological and heritage value. Macroinvertebrates are bioindicators of the health of aquatic ecosystems. The aim of this study was to assess the effects of dewatering and re-watering cycles on benthic macroinvertebrate (BMI) communities. Two data collections were carried out at two stations (Okpara 1 and Okpara 2) on the Okpara river before and after dewatering. Thus, 8 samples of benthic macroinvertebrates and 12 physico-chemical parameters (T°C, pH, Transparency, Depth, Conductivity, Dissolved Oxygen that were measured in situ, and BOD5, COD, NH<sub>4</sub><sup>+</sup>, NO<sub>3</sub><sup>-</sup>, NO<sub>2</sub><sup>-</sup> and PO<sub>4</sub><sup>3-</sup>) were assayed in the laboratory. Canonical Correspondence Analysis (CCA) was used to match physico-chemical data to MIB families. Shannon and Piélou diversity indices were used to determine the effects of dewatering on MIBs. The increase in temperature values of pH, BOD5, COD, NH4</sub>+</sup>, NO3</sub>-</sup>, NO2</sub>-</sup> and PO4</sub>3-</sup>, after re-watering indicates the effect of dewatering on the quality of Okpara aquatic ecosystems. The benthic macrofauna collected consisted of 62.42% insects, 0.65% crustaceans, 6.48% molluscs, 0.72% worms and 0.14% arachnids. Whereas after re-watering, 21.67% insects, 0% crustaceans, 0.22% molluscs, 7.56% worms and 0.29% arachnids were recorded. Insects, crustaceans and molluscs were more abundant before dewatering than after. This was revealed by low abundances and taxonomic richness, as well as low Shannon index values of samples collected after re-watering.
基金Supported by the Science and Technology Planning Project of Guangdong(2006A36701004)the Basic Research Program of the Ministry of Environmental Protection(zx_200910_02)
文摘The carbonaceous adsorbent was prepared from mixtures of dewatered sludge and sawdust with enhanced ZnCl2 chemical activation.Characteristics of the adsorbent were studied using scanning electron microscope(SEM) ,Fourier transform infrared spectroscopy(FT-IR) ,and adsorption of nitrogen.The surface analysis showed that the carbonaceous adsorbent had good specific surface and porosity(394 m 2 ·g-1of BET surface,0.12 and 0.10 ml·g-1of microporous and mesoporous volume,respectively) .The oxygen functional groups such as OH,C O and C O were found on the surface by FTIR and XPS(X-ray photoelectron spectroscopy) .The adsorption of elemental mercury(Hg0) on the carbonaceous adsorbent was studied in a fixed bed reactor.The dynamic adsorption capacity of carbonaceous adsorbent increased with influent mercury concentration,from 23.6μg·g-1at 12.58μg·m-3to 87.9μg·g-1at 72.50μg·m-3,and decreased as the adsorption temperature increased,from 246 μg·g-1 at 25°C to 61.3μg·g-1 at 140°C,when dry nitrogen was used as the carrier gas.The carbonaceous adsorbent presented higher dynamic adsorption capacity than activated carbon,which was 81.2μg·g-1and 53.8μg·g-1respectively.The adsorption data were fitted to the Langmuir adsorption model.The physical and chemical adsorption were identified on the adsorbent.
基金Supported by Jiangsu Agricultural Science and Technology Innovation Fund[CX(13)3031]~~
文摘[Objective]The aim was to research water retention of superabsorbent polymer （SAP） in sandy soils. [Method] With soils from an ancient course in the Yel ow River as materials, acrylate SAP was taken as water retention materials to conduct the test. [Result] With 0.2%-0.4% SAP added, dewatering period of sandy soil extended after irrigation; the period of water retention quantity over 10% last for 42 d, which was significantly more than that of the control group in 16 d （saturated water reducing to 10%）; water retention effect proved better at the 2nd irrigation without soil stirring compared with the 1st irrigation. [Conclusion] The mixture of SAP with sandy soils promotes water retention in soils.
基金Supported by the Science and Technology Commission of Shanghai Municipality (08 DZ 1202802,09 DZ 1204105,09 DZ2251700)the National Natural Science Foundation of China (51008322)
文摘This research evaluated the use of sewage sludge and refuse incineration bottom ash to replace calcium sulfoaluminate cement （CSA） in making controlled low-strength material （CLSM）. Various properties of CLSM mixtures were characterized in terms of unconfined compressive strength, microstructure and leachability. It was found that the strength of tested CLSM mixtures ranged from 3.6 to 9.0 MPa, over the upper excavatable limit of 2.1 MPa. The micro-structural analysis revealed that sewage sludge and bottom ash were crystallochemically in- corporated within CLSM system_s by forming the needle-like ettringite （C3A＇3CS＇_H32） with exiguous tu.bers via the typical Pozzolanic Reaction, leading to a dense and low-porosity microst;＇ucture. Furthermore,-the toxicity characteristic leaching procedure evidenced that the cumulative leachable metals in the leachate were much below the regulatory thresholds. The potential for us!ng sewage sludge and bottom ash!n CLSM makin.g was thus confirmed.
基金Supported by Scientific Research Foundation of Yunnan Provincial Education Department(09Y0292)~~
文摘[Objective] The technological parameter suitable for the dewatering of dredged sediment from Dianchi Lake was studied.[Method] By means of the treatment method of sewage sludge in sewage treatment plant,flocculants including FeCl3,Al2(SO4)3 and PAM were taken as dewatering agents which were added in dredged sediment.[Result] The results showed that Al2(SO4)3 had better dewatering effect than FeCl3 and PAM,and the optimum dosing quantity of Al2(SO4)3 in dredged sediment was 170 mg/L,in addition,the water quality of supernatant met the first class B standard of GB18918-2002 and could be directly discharged to nature water without pollution.[Conclusion] The study could provide a simple and feasible way for the rapid dewatering of dredged sediment from Dianchi Lake,which would be convenient for the disposal and resource utilization of dredged sediment.
文摘The slurry settling characteristics are the most important to design a thickener in process industries. In this work, the iron ore slurry from the screw classifier overflow was used for the settling study. It was observed that the original slurry exhibited a low settling velocity and a turbid supernatant during the settling process. Commercial flocculating agents with anionic, cationic, and nonionic characters were used to improve the settling behavior of suspensions, which were added into the slurry at different ranges of slurry pH values, respectively. The settling results show that the use of flocculants increase the settling rate by several times. Compared with the cationic and non-ionic flocculants, the anionic flocculant is more effective in enhancing the slurry settling rate. The small dose of the anionic flocculant is found to be more effective, but the other flocculants are less effective even at higher dosages. The simulation of an industrial thickener was carried out based on the laboratory settling data, and the appropriate design and selection parameters of the industrial thickener were estimated.
基金supported by the China Postdoctoral Science foundation (No.2018M642479)the National Natural Science Foundation of China (No.51821006)the Postdoctoral Science Foundation of Zhejiang Province (No.zj20180141).
文摘Enhancing sludge dewatering is of importance in reducing environmental burden and disposal costs.In this work, a cationic surfactant, cetyl trimethyl ammonium bromide(CTAB), was combined with Fenton’s reagent for sludge dewatering.Results show that the Fenton-CTAB conditioning significantly promotes the sludge dewatering.Using combined techniques of response surface methodology and uniform design, dosages of Fe2+, H2O2, and CTAB for water content response were optimized to be 89, 276, and 233 mg/g dry solids(DS),respectively.The water content of sludge decreased from 79.0% to 66.8% under the optimal conditions.Compared with cationic polyacrylamide, the Fenton-CTAB system exhibited superior sludge dewatering performance.To gain insights into the mechanisms involved in sludge dewatering, the effects of Fenton-CTAB conditioning on the composition of extracellular polymeric substances(EPS) and the morphology of the sludge flocs were investigated.The decomposition of EPS into some dissolved organics and the release of proteins in tightly bound EPS facilitated the conversion of bound water to free water and further reduced the water content of sludge cake.After conditioning, morphology of sludge showed aggregation.Overall, the enhanced sludge dewatering by Fenton-CTAB treatment provides an efficient way for management of sewage sludge.
文摘A technology of ultrasonic-electric united desalting and dewatering of crude oil is studied. The ultrasonic setup is designed to form a standing-wave field, which is more efficient for agglomeration of water particles. The desalting and dewatering results of the ultrasonic-electric united process are compared with those of the electric process. For high salt-contenting crude oil （40-70 mg·L ^-1）, the salt content is still above 10.0 mg·L^-1 after crude oil has been treated by two-stage electric desalting process in refinery, which cannot meet the need of refinery. Ultrasonic-electric united process is a novel technology for treating the high salt-contenting oil. On the optimal operating conditions of the ultrasonic-electric united process, the salt content of crude oil can be reduced from 67 5 mg·L^-1 to 3.97 mg·L ^-1 by one-stage ultrasonic-electric united process, and the water content falls below 0.3% （by volume）. The results show that the ultrasonic-electric united process is more effective than the electric process in high salt-contenting oil desalting. This technology should be useful in the refinery process.
基金support from the Ministry of Steel,Government of India,India(GAP 214).
文摘This paper reports the systematic investigation on the flocculation,sedimentation and consolidation characteristics of kaolinite using guar gum as a green flocculant.In-situ flocculation behavior of kaolinite at various pH,guar gum dosages,and ionic strength were studied using a light scattering technique.The effect of these parameters on the settling rate,solid consolidation,and supernatant liquid clarity was recorded.The morphology of kaolinite and flocculated kaolinite aggregates were analyzed using FESEM.The morphology studies suggest that it is poorly crystalline with multiple steps on edge,broken edge;laminar with high aspect ratio and have rough basal surface.The complex irregularity on the basal surface and the presence of multiple steps in the edges,broken edges(hydroxyl groups)have facilitated the guar gum adsorption.The isoelectric point of kaolinite is pH 3.96.The pH,ionic strength and flocculant dosage have a significant effect on the kaolinite settling rate.The guar gum has exhibited excellent turbidity removal efficiency at pH 5.The turbidity removal is inefficient at pH 10.However,guar gum has shown high turbidity removal with 80%transmission at pH 10 in the presence of a KNO3 electrolyte.
基金This work was financially supported by the State Key Laboratory of Safety and Health for Metal Mines,China(No.2019-JSKSSYS-02)the Natural Science Foundation of Hunan Province,China(No.2020JJ5718).
文摘Rapid flocculation and settlement(FS)of mine tailings is significant for the improvement and development of the filling process,whereas the settlement velocity(SV)of tailings in FS has been recognized as a key parameter to evaluate the settlement effect.However,the influence of temperature on the SV and its mechanism have not been studied.FS experiments on tailings with various ambient temperatures were carried out.The SVs of tailings with a solid waste content of 10wt%and an anionic polyacrylamide content of 20 g·t^−1 were measured at different temperatures.The SV presented an“N”-shaped variation curve as the temperature changed from 5 to 40℃.The mechanism of these results can be explained from the perspective of the electric double-layer repulsive force,molecular dynamics,and the polymer flocculation principle,as revealed from the scanning electron microscopy of floc particles.The findings will be beneficial in the design of tailings dewatering processes and save costs in the production of cemented paste backfill.
基金supported by the National Natural Science Foundation of China(U2003125)。
文摘The filtration and dewatering of fine clean coal not only ensure industrial water recycle in coal washing plant,but also reduce the moisture of coal product in order to meet the requirements of combustion or coking industry.Fine clean coal is mainly composed by organic matter,and the property difference of different organic matter determines the filtration and dewatering behavior.In this investigation,vitrinite and inertinite were separated from a clean bituminous coal,and the comparative filtration and dewatering behavior of vitrinite and inertinite were conducted.The results showed that inertinite has lower dewatering rate and higher filter cake moisture than vitrinite.The analysis of filter cake structure showed that inertinite particle is easier to be broken into small particles due to the difference of mechanical properties,thus forming more compact filter cake than vitrinite.The analysis of particle surface properties showed that vitrinite is more hydrophobic than inertinite,which makes water easier drained from filter cake.The simulation study showed that the structure of inertinite is more porous than that of vitrinite,and the interaction between inertinite and water is stronger than that between vitrinite and water.This study provides a theoretical basis for improving coal dewatering by selectively improving coal maceral hydrophobicity.
基金This work was supported by the National Natural Science Foundation of China(No.51608166)the China Scholarship Council(No.201906705003).
文摘Ultraviolet(UV)assisted zero-valent iron(ZVI)-activated sodium persulfate(PDS)oxidation(UV-ZVI-PDS)was used to treat waste activated sludge(WAS)in this study.The dewaterability performance and mechanism of WAS dewatering were analyzed.The results showed that UV-ZVI-PDS can obtain better sludge dewatering performance in a wide pH range(2.0-8.0).When the molar ratio of ZVI/PDS was 0.6,UV was 254nm,PDS dosage was 200 mg/g TS(total solid),pH was 6.54,reaction time was 20 min,the CST(capillary suction time)and SRF(specific resistance to filtration)were decreased by 64.0%and 78.2%,respectively.The molar ratio of ZVI/PDS used in this paper is much lower than that of literatures,and the contents of total Fe and Fe^(2+) in sludge supernatant remained at a low level,as 3.7 mg/L and 0.0 mg/L.The analysis of extracellular polymeric substances(EPS),scanning electron microscope(SEM)and particle size distribution showed that the EPS could be effectively destroyed by UV-ZVI-PDS,the sludge flocs broken down into smaller particles,cracks and holes appeared,and then the bound water was released.At the same time,the highly hydrophilic tightly bound-EPS(TB-EPS)were converted into loosely bound EPS(LB-EPS)and soluble EPS(S-EPS).During sludge pretreated by UV-ZVI-PDS,positively charged ions,such as Fe^(2+),Fe^(3+) and H^(+),produced in the reaction system could reduce the electronegativity of sludge surface,promote sludge particles aggregation,and then enhanced the sludge dewaterability.
基金funded by the National Natural Science Foundation of China (No. 51278489)Key Lab for Solid Waste Management and Environmental Safety Open fund (No. 2011-8)
文摘A key step in sludge treatment is sludge dewatering. However, activated sludge is generally very difficult to be dewatered. Sludge dewatering performance is largely affected by the sludge moisture distribution. Sludge disintegration can destroy the sludge structure and cell wall, so as change the sludge floc structure and moisture distribution, thus affecting the dewatering performance of sludge. In this article, the disintegration methods were ultrasound treatment, K2 Fe O4oxidation and KMn O4 oxidation. The degree of disintegration（DDCOD）, sludge moisture distribution and the final water content of sludge cake after centrifuging were measured. Results showed that three disintegration methods were all effective, and K2 Fe O4oxidation was more efficient than KMn O4 oxidation. The content of free water increased obviously with K2 Fe O4and KMn O4 oxidations, while it decreased with ultrasound treatment. The changes of free water and interstitial water were in the opposite trend. The content of bounding water decreased with K2 Fe O4oxidation, and increased slightly with KMn O4 oxidation, while it increased obviously with ultrasound treatment. The water content of sludge cake after centrifuging decreased with K2 Fe O4oxidation, and did not changed with KMn O4 oxidation, but increased obviously with ultrasound treatment. In summary, ultrasound treatment deteriorated the sludge dewaterability, while K2 Fe O4and KMn O4 oxidation improved the sludge dewaterability.
基金“The Pearl River Talent Recruitment Program”in 2019(Grant No.2019CX01G338)Guangdong Province and the Research Funding of Shantou University for New Faculty Member(Grant No.NTF19024-2019)the National Natural Science Foundation of China(NSFC)(Grant No.41807235).
文摘When pumping is conducted in confined aquifer inside excavation pit(waterproof curtain),the direction of the groundwater seepage outside the excavation changes from horizontal to vertical owing to the existence of the curtain barrier.There is no analytical calculation method for the groundwater head distribution induced by dewatering inside excavation.This paper first analyses the mechanism of the blocking effects from a close barrier in confined aquifer.Then,a simple equation based on analytical solution is proposed to calculate groundwater heads inside and outside of the excavation pit with waterproof curtain(hereafter refer to close barrier)in a confined aquifer.The distribution of groundwater head is derived according to two conditions:(i)pumping with a constant water head,and(ii)pumping with a constant flow rate.The proposed calculation equation is verified by both numerical simulation and experimental results.The comparisons demonstrate that the proposed model can be applied in engineering practice of excavation.
