The hard-to-remove lattice water has been regarded as a significant obstacle impeding the practical use of Prussian blue analogue cathodes for sodium-ion batteries.This work monitored the electrochemical evolution of ...The hard-to-remove lattice water has been regarded as a significant obstacle impeding the practical use of Prussian blue analogue cathodes for sodium-ion batteries.This work monitored the electrochemical evolution of a hydrated monoclinic sodium manganese hexacyanoferrate cathode by solid-state nuclear magnetic resonance(NMR).For the first time,we established a correlation between the chemical shifts of ^(23)Na NMR signals and the presence or absence of lattice water within this cathode.Through this method,we verified the electrochemical dehydration process that coincides with the merging of two redox platforms and a phase transformation in the initial cycles.Furthermore,we discovered that the lattice water is completely removed after several-day cell rest following a single activation cycle.展开更多
In this context,the present study proposes the use of microwave irradiation to improve the dehydration rate and efficiency of strontium hydroxide octahydrate(Sr(OH)_(2)·8H_(2)O)without introducing contaminants.Th...In this context,the present study proposes the use of microwave irradiation to improve the dehydration rate and efficiency of strontium hydroxide octahydrate(Sr(OH)_(2)·8H_(2)O)without introducing contaminants.This study revealed that the use of microwave irradiation to dehydrate Sr(OH)_(2)·8H_(2)O is feasible and surprisingly efficient.The effects of this approach on important parameters were investigated using response surface methodology(RSM).The results revealed that the microwave dehydration process follows a linear polynomial model.In addition,compared with the heating time and material thickness,the microwave-assisted dehydration of Sr(OH)_(2)·8H_(2)O is sensitive to the microwave power and not to the material mass.The relative dehydration percentage reached 99.99%when heated in a microwave oven at 950Wfor just 3 min.In contrast,a relative dehydration percentage of 94.6%was reached when heated in an electric furnace at 180℃for 120 min.The XRD spectra also revealed that most of the Sr(OH)_(2)·8H_(2)O transformed into Sr(OH)_(2)after dehydration via microwave irradiation,whereas a significant portion of the Sr(OH)_(2)·H_(2)O remained after conventional electric dehydration.The experimental data were fitted and analyzed via the thin-layer drying dynamics model,and the results indicated that the dehydrating behavior of Sr(OH)_(2)·8H_(2)O could be well described by the Page model.展开更多
Isosorbide is a novel bio-based material derived as a secondary dehydration product of sorbitol.This work focuses on the kinetics of sulfuric acid-catalyzed dehydration of sorbitol under conditions of nonconstant volu...Isosorbide is a novel bio-based material derived as a secondary dehydration product of sorbitol.This work focuses on the kinetics of sulfuric acid-catalyzed dehydration of sorbitol under conditions of nonconstant volume.Herein,the effects of stirring rate,catalyst dosage,reaction temperature,and reaction time on the dehydration reaction of sorbitol were investigated.The yield of isosorbide up to 77.13%was obtained after 1.5 h of reaction time under conditions of 2 kPa,1.0%(mass)catalyst dosage,and 413.15 K.Based on the sorbitol dehydration reaction mechanism and a simplified reaction network,a kinetic model was developed in this work.A good agreement was accomplished between kinetic modeling and experiments between 393.15 and 423.15 K.The fitting results indicate that side reactions with higher activation energies are more affected by reaction temperatures,and the main side reaction that influences the selectivity of isosorbide is the oligomerization reaction among the primary dehydration products of sorbitol.The model fitting of the catalyst amounts effect shows that the effective concentration of sulfuric acid would be reduced with the increase of dosage due to the molecular agglomeration effect.Hopefully,the kinetic experiments and modeling results obtained in this work will be helpful to the design and optimization of the industrial sorbitol dehydration process.展开更多
Drought events have become more severe under climate change,and this can pose a major threat to the survival of various organisms.The molecular mechanisms involved in dehydration resistance are not well known.Here,adu...Drought events have become more severe under climate change,and this can pose a major threat to the survival of various organisms.The molecular mechanisms involved in dehydration resistance are not well known.Here,adults of the migratory locust,Locusta migratoria,were subjected to food-mediated dehydration,and adipokinetic hormone(AKH)signaling was found to play a key role in regulating dehydration resistance.Specifically,dehydration shortened the lifespan,increased the body weight loss,and reduced the water loss rate in adult locusts.Global transcriptome profiles revealed variations in tissue-specific gene expression between dehydration-resistant locusts and normal locusts.Importantly,dehydration selection and exposure induced prominent expression of AKH genes in the retrocerebral complex of adult locusts.Furthermore,individual knockdown of AKH1,AKH2,or AKH receptor(AKHR)accelerated water loss and shortened the lifespan of adult locusts under dehydration conditions,and trehalose supplementation ameliorated the negative effects caused by interference with AKH or AKHR.These findings demonstrated that AKH/AKHR signaling-dependent trehalose metabolism plays a crucial role in regulating locust dehydration resistance and thus provide novel insights into the regulatory mechanism underlying drought resistance.展开更多
Significant waste resources are generated in the form of water-oil emulsions.These emulsions cannot be effectively destroyed on an industrial scale by traditional methods that rely on the settling of the aqueous phase...Significant waste resources are generated in the form of water-oil emulsions.These emulsions cannot be effectively destroyed on an industrial scale by traditional methods that rely on the settling of the aqueous phase,and therefore,they accumulate in large quantities.Thermomechanical dehydration,based on the evaporation of the water phase,presents a promising process for recycling such waste.However,within the framework of thermomechanical dehydration,the issue of optimizing energy costs for heating raw materials and controlling the water content in the product arises.Standard methods of determining water content under the boiling conditions of highly stable water-hydrocarbon emulsions are characterized by low efficiency,as they require constant sampling and the involvement of additional equipment and personnel.Consequently,this presents a challenge in predicting and creating an automated thermomechanical dehydration process.Therefore,dynamic curves depicting changes in the water content of these emulsions,depending on the temperature of the boiling liquid,have been obtained.It is proposed to determine the rate of temperature increase(dT/dt)of the boiling emulsion for continuous,real-time monitoring of the residual water content and for recording the moment of complete dehydration.Achieving a boiling emulsion temperature of 130-170℃(or higher)and/or the rate of temperature increase from 3.0 to 5.5(or above)indicates the complete dehydration of the emulsion.The proposed method can be implemented in any industrial or laboratory-scale unit for thermomechanical dehydration without significant capital costs.It is based on the use of simple devices consisting of temperature sensors and a computing unit for determining the temperature and rate of heating.展开更多
In recent decades,MgSO_(4)·7H_(2)O(epsomite)has attracted significant attention as a promising thermochemical-based thermal energy storage material due to its high theoretical energy density,wide availability,and...In recent decades,MgSO_(4)·7H_(2)O(epsomite)has attracted significant attention as a promising thermochemical-based thermal energy storage material due to its high theoretical energy density,wide availability,and affordability.Despite extensive research efforts,progress in achieving high-energy density has been limited,primarily due to inadequate understanding of its reaction mechanisms and unfavorable dehydration/hydration kinetics.This study systematically investigated the hydration/dehydration kinetics and cyclability of MgSO_(4)·7H_(2)O.The results reveal that the dehydration process is influenced by the heating rate,with an optimal rate of 5℃/min,resulting in a seven-step MgSO_(4)·7H_(2)O dehydration process with a dehydration heat close to the theoretical value.The reaction kinetic analysis indicated that the rate of hydration was approximately 50%lower than that of dehydration.In addition,thermal cycling tests of MgSO_(4)·7H_(2)O under the conditions of this study(small sample size)indicated good cyclability,with hydration rates increasing with increasing cycling numbers up to approximately 10 cycles where level-off occurs.These results are consistent with scanning electron microscopy analyses,which revealed the formation of cracks and channels in the salt hydrate particles,facilitating mass transfer and improved kinetics.展开更多
The single phase La2（CO3）3·3.4H2 O was synthesized by hydrothermal method. The thermal decomposition and intermediates and final solid products of La2（CO3）3·3.4H2O from 30 to 1000 °C were characteri...The single phase La2（CO3）3·3.4H2 O was synthesized by hydrothermal method. The thermal decomposition and intermediates and final solid products of La2（CO3）3·3.4H2O from 30 to 1000 °C were characterized by XRD, FTIR and DTA-TG. The kinetics of dehydration of La2（CO3）3·3.4H2O in the temperature range of 30-366 °C was investigated under non-isothermal conditions. Flynn-Wall-Ozawa and Friedman isoconversion methods were used to calculate the activation energy and analyze the reaction steps; multivariate non-linear regression program was applied to determine the most probable mechanism and the kinetic parameters. The results show that the thermal dehydration of La2（CO3）3·3.4H2O is a kind of three-step competitive reaction, and controlled by an n-order initial reaction followed by n-order competitive reaction（FnFnFn model）. The activation energy matching with the most probable model is close to value obtained by Friedman method. The fitting curves match the original TG-DTG curves very well.展开更多
The chlorophyll fluorescence kinetics of marine red alga Grateloupia turutunt Yamada, green alga Ulva pertusa Kjellm and brown alga Laminaria japonica Aresch during natural sustained dehydration were monitored and inv...The chlorophyll fluorescence kinetics of marine red alga Grateloupia turutunt Yamada, green alga Ulva pertusa Kjellm and brown alga Laminaria japonica Aresch during natural sustained dehydration were monitored and investigated. The pulse amplified modulation (PAM) system was used to analyze the distinct fluorescence parameters during thallus dehydration. Results proved that the fluorescence kinetics of different seaweed all showed three patterns of transformation with sustained water loss. These were: 1) peak kinetic pattern (at the early stage of dehydration fluorescence enhanced and quenched subsequently, representing a normal physiological state). 2) plateau kinetic pattern (with sustained water loss fluorescence enhanced continuously but quenching became slower, finally reaching its maximum). 3) Platform kinetic pattern (fluorescence fell and the shape of kinetic curve was similar to plateau kinetic pattern). A critical water content (CWC) could be found and defined as the percentage of water content just prior to the fluorescence drop and to be a significant physiological index for evaluation of plant drought tolerance. Once thallus water content became lower than this value the normal peak pattern can not be recovered even through rehydration, indicating an irreversible damage to the thylakoid membrane. The CWC value corresponding to different marine species were varied and negatively correlated with their desiccation tolerance, for example. Laminaria japonica had the highest CWC value (around 90%) and the lowest dehydration tolerance of the three. In addition, a fluorescence 'burst' was found only in red algae during rehydration. The different fluorescence parameters F-o, F-v and F-v, F-m were measured and compared during water loss. Both F-o and F-v increased in the first stage of dehydration but F-v/F-m. kept almost constant. So the immediate response of in vivo chlorophyll fluorescence to dehydration was an enhancement. Later with sustained dehydration F-o increased continuously while F-v decreased and tended to become smaller and smaller. The major changes in fluorescence (including fluorescence drop during dehydration and the burst during rehydration) were all attributed to the change in F-o instead of F-v This significance of F-o indicates that it is necessary to do more research on F-o as well as on its relationship with the state of thylakoid membrane.展开更多
Iron exchanged ZSM-5 with Si/Al ratio from 25 to 300 prepared by three consecutive ion exchanges was used for the dehydration of ethanol to ethylene.The iron exchanged ZSM-5（Si/Al=25） catalyst with an iron content o...Iron exchanged ZSM-5 with Si/Al ratio from 25 to 300 prepared by three consecutive ion exchanges was used for the dehydration of ethanol to ethylene.The iron exchanged ZSM-5（Si/Al=25） catalyst with an iron content of 0.46 wt%gave 97%-99%yield of ethylene at 98%-99%conversion of ethanol at 260℃ and 0.81 h^-1 liquid hourly space velocity.The high performance was maintained for60 d on-stream.X-ray diffraction,Fourier transform infrared spectroscopy of pyridine adsorption,NH3 temperature-programmed desorption and diffuse reflectance UV-vis spectroscopy were used for catalyst characterization.Ion exchange with iron decreased the total acidity of the zeolite,especially the strong acid sites and Bronsted acid sites.The doped iron species were distributed over Fe-ZSM-5 as predominantly isolated Fe^3＋.Therefore,the catalytic performance for ethanol dehydration to ethylene was improved.展开更多
Various ZSM-5 zeolites modified with alkali metals （Li, Na, K, Rb, and Cs） were prepared using ion exchange. The catalysts were used to enhance the catalytic dehydration of lactic acid （LA） to acrylic acid （AA）....Various ZSM-5 zeolites modified with alkali metals （Li, Na, K, Rb, and Cs） were prepared using ion exchange. The catalysts were used to enhance the catalytic dehydration of lactic acid （LA） to acrylic acid （AA）. The effects of cationic species on the structures and surface acid-base distributions of the ZSM-5 zeolites were investigated. The important factors that affect the catalytic performance were also identified. The modified ZSM-5 catalysts were characterized using X-ray diffraction, tempera- ture-programmed desorptions of NH3 and CO2, pyridine adsorption spectroscopy, and N2 adsorption to determine the crystal phase structures, surface acidities and basicities, nature of acid sites, specific surface areas, and pore volumes. The results show that the acid-base sites that are adjusted by alkali-metal species, particularly weak acid-base sites, are mainly responsible for the formation of AA. The KZSM-5 catalyst, in particular, significantly improved LA conversion and AA selectivity because of the synergistic effect of weak acid-base sites. The reaction was conducted at different reaction temperatures and liquid hourly space velocities （LHSVs） to understand the catalyst selectivity for AA and trends in byproduct formation. Approximately 98% LA conversion and 77% AA selectivity were achieved using the KZSM-5 catalyst under the optimum conditions （40 wt% LA aqueous solution, 365 ℃, and LHSV 2 h-1）.展开更多
Formic acid （HCOOH） decomposition at Pt film electrode has been studied by electrochem- ical in situ FTIR spectroscopy under attenuated-total-reflection configuration, in order to clarify whether bridge-bonded forma...Formic acid （HCOOH） decomposition at Pt film electrode has been studied by electrochem- ical in situ FTIR spectroscopy under attenuated-total-reflection configuration, in order to clarify whether bridge-bonded formate （HCOOD） is the reactive intermediate for COad for-mation from HCOOH molecules. When switching from HCOOH-free solution to HCOOH- containing solution at constant potential （E=0.4 V vs. RHE）, we found that immediately upon solution switch COad formation rate is the highest, while surface coverage of formate is zero, then after COad formation rate decreases, while formate coverage reaches a steady state coverage quickly within ca. 1 s. Potential step experiment from E=0.75 V to 0.35 V, reveals that formate band intensity drops immediately right after the potential step, while the COad signal develops slowly with time. Both facts indicate that formate is not the reactive intermediate for formic acid dehydration to CO.展开更多
Pervaporation(including vapor permeation) is a kind of new membrane separation technology, possessing the advantages of high efficiency, energy saving and convenient operation. It has promising application in the sepa...Pervaporation(including vapor permeation) is a kind of new membrane separation technology, possessing the advantages of high efficiency, energy saving and convenient operation. It has promising application in the separation and purification of organic solvents. Dehydration is an important step in the production and recovery of organic solvents. Zeolite membranes have attracted wide attention for pervaporation dehydration due to their high separation performance and good thermal/chemical stability. So far, zeolite membranes have been preliminarily industrialized for dehydration of organic solvents. This paper reviews the recent development of zeolite membranes for pervaporation dehydration, including mass transfer models, preparation and applications of zeolite membranes. The review also discusses the current industrial applications of zeolite membranes and their future development in pervaporation.展开更多
A new type of dehydration unit for natural gas was briefly described and its basic structure and working principles were presented. An indoor test rig for testing the unit performance was set up and the experimental r...A new type of dehydration unit for natural gas was briefly described and its basic structure and working principles were presented. An indoor test rig for testing the unit performance was set up and the experimental results were given. The results showed that the unit could attain a maximum dew point depression of about 20℃ without any need of external mechanical power and chemicals. The pressure loss ratio, shock wave and the flow rate had great influence on the dehydration characteristics. From the systematic analysis of the factors that affect the dehydration efficiency of the unit, the suggestions for improving the unit are put forward.展开更多
NaA zeolite membranes with 80 cm in length and 12.8 mm in outer diameter were prepared by our research group cooperating with Nanjing Jiusi Hi-Tech Co., China. The influence of dissolved inorganic salts and pH value i...NaA zeolite membranes with 80 cm in length and 12.8 mm in outer diameter were prepared by our research group cooperating with Nanjing Jiusi Hi-Tech Co., China. The influence of dissolved inorganic salts and pH value in the feed of isopropanol （IPA） solution on NaA zeolite membranes was investigated. It was found that both factors exhibited strong influence on the stability of NaA zeolite membranes. A set of pretreatment steps such as pH adjustment and distillation of the IPA solution were proposed to improve stability for pervaporation dehydration. An industrial-scale pervaporation facility with 52 m2 membrane area was built to dehydrate IPA solution from industrial cephalosporin production. The facility was continuously operated at 368-378 K to dehydrate IPA solution from water mass content of 15%-20% to less than 2% with a feed flow rate of 400-500 L·h^-1 and an average water flux of 1-1.5 kg·m^-2·h-1. The successful application of this facility suggested a promising application of NaA zeolite mem-brane for IPA recovery from pharmaceutical production.展开更多
This paper compares three methods for natural gas dehydration that are widely applied in industry：（1） absorption by triethylene glycol, （2） adsorption on solid desiccants and （3） condensation. A comparison is m...This paper compares three methods for natural gas dehydration that are widely applied in industry：（1） absorption by triethylene glycol, （2） adsorption on solid desiccants and （3） condensation. A comparison is made according to their energy demand and suitability for use. The energy calculations are performed on a model where 105 Nm3/h water saturated natural gas is processed at 30 °C. The pressure of the gas varies from 7 to 20 MPa. The required outlet concentration of water in natural gas is equivalent to the dew point temperature of -10 °C at gas pressure of 4 MPa.展开更多
The production of acrylates from biomass-originated lactic acid is of extraordinary importance, to overcome the increasing worldwide shortage of petroleum. In this study, the catalytic dehydration of methyl lactate ov...The production of acrylates from biomass-originated lactic acid is of extraordinary importance, to overcome the increasing worldwide shortage of petroleum. In this study, the catalytic dehydration of methyl lactate over a calcium sulfate catalyst, with various promoters, has been carried out to identify potential catalyst/promoter combinations for acrylate production. The best catalyst for methyl acrylate formation in this study has been calcium sulfate, with cupric sulfate and phosphates as promoters. The optimal mass ratio of m（CaSOa） ： m（CuSOa） ： m（Na2HPO4） ： m（KH2PO4） is 150.0 ： 13.8 ： 2.5 ： 1.2. Effects of carrier gas, reaction temperature, feed concentration as well as contact time on the dehydration of methyl lactate have been investigated. With nitrogen as a carrier gas, a combined yield of acrylic acid and methyl acrylate is 63.9% from 60% （by mass） methyl lactate at 400℃ with 7.7 seconds contact time.展开更多
In order to concentrate the diluted sulfuric acid from the titanium dioxide(TiO2)production of sulphate process,a new concentration process was proposed by coupling chemical dehydration and multi-effect evaporation.Th...In order to concentrate the diluted sulfuric acid from the titanium dioxide(TiO2)production of sulphate process,a new concentration process was proposed by coupling chemical dehydration and multi-effect evaporation.The ferrous sulfate monohydrate(FeSO4·H2O),as the dehydrant,was added to the diluted sulfuric acid to form ferrous sulfate heptahydrate(FeSO4·7H2O)according to the H2SO4-FeSO4-H2O phase diagrams,which partially removes the water.This process was named as Chemical Dehydration Process.The residual water was further removed by two-effect evaporation and finally 70 wt%sulfuric acid was obtained.The FeSO4·H2O can be regenerated through drying and dehydration of FeSO4·7H2O.The results show that FeSO4·H2O is the most suitable dehydrant,the optimal reaction time of chemical dehydration process is 30 min,and low temperature is favorable for the dehydration reaction.45.17%of the entire removed water can be removed by chemical dehydration from the diluted sulfuric acid.This chemical dehydration process is also energy efficient with 24.76%saving compared with the direct evaporation process.Furthermore,51.21%of the FeSO4 dissolved originally in the diluted sulfuric acid are precipitated out during the chemical dehydration,which greatly reduces the solid precipitation and effectively alleviates the scaling in the subsequent multi-effect evaporation process.展开更多
Acid-catalyzed dehydration of alcohols has been widely employed for the synthesis of alkenes. However, activated alcohols when employed as substrates in dehydration reactions are often pla-gued by the lack of alkene s...Acid-catalyzed dehydration of alcohols has been widely employed for the synthesis of alkenes. However, activated alcohols when employed as substrates in dehydration reactions are often pla-gued by the lack of alkene selectivity. In this work, the reaction system can be significantly improved through enhancing the performance of Lewis acid catalysts in the dehydration of activated alcohols by combining with a Lewis base. Observations of the reaction mechanism revealed that the Lewis base component might have changed the reaction rate order. Although both the principal and side reaction rates decreased, the effect was markedly more observed on the latter reaction. Therefore, the selectivity of the dehydration reaction was improved. On the basis of this observation, a new route to synthesize 2-cinnamyl-1,3-dicarbonyl compounds was developed by using 2-aryl-3,4- di-hydropyran as a starting substrate in the presence of a Lewis acid/Lewis base combined catalyst system.展开更多
Micro-mesoporous composite molecular sieves H-ZSM-5/MCM-41 were prepared by the hydrothermal technique with alkali-treated H-ZSM-5zeolite as the source and characterized by scanning electron microscopy,transmission el...Micro-mesoporous composite molecular sieves H-ZSM-5/MCM-41 were prepared by the hydrothermal technique with alkali-treated H-ZSM-5zeolite as the source and characterized by scanning electron microscopy,transmission electron microscopy,energy dispersive spectroscopy,X-ray diffraction,N2 adsorption-desorption measurement and NH3 temperature-programmed desorption.The catalytic performances for the methanol dehydration to dimethyl ether over H-ZSM-5/MCM-41 were evaluated.Among these catalysts,H-ZSM-5/MCM-41 prepared with NaOH dosage (nNa/nSi) varying from 0.4 to 0.47 presented excellent catalytic activity with more than 80%methanol conversion and 100%dimethyl ether selectivity in a wide temperature range of 170—300℃,and H-ZSM-5/MCM-41 prepared with nNa/nSi=0.47 showed constant methanol conversion of about 88.7%,100% dimethyl ether selectivity and excellent lifetime at 220℃.The excellent catalytic performances were due to the highly active and uniform acidic sites and the hierarchical porosity in the micro-mesoporous composite molecular sieves.The catalytic mechanism of H-ZSM-5/MCM-41 for the methanol dehydration to dimethyl ether process was also discussed.展开更多
A series of nanocrystalline γ-alumina are synthesized by different procedures, namely, thermal decomposition method （sample A）, precipita-tion method （sample B） and sol-gel method using sucrose and hexadecyltrime...A series of nanocrystalline γ-alumina are synthesized by different procedures, namely, thermal decomposition method （sample A）, precipita-tion method （sample B） and sol-gel method using sucrose and hexadecyltrimethyl ammonium bromide （CTAB） as templates （samples C and D, respectively）. Textural and acidic properties of γ-alumina samples are characterized by XRD, N2 adsorption-desorption and NH3-TPD techniques. Vapor-phase dehydration of methanol into dimethyl ether is carried out over these samples. Among them, sample C shows the highest catalytic activity. NH3-TPD analysis reveals that the sample with smaller crystallite size possesses higher concentration of medium acidic sites and consequently higher catalytic activity. Thermal decomposition method leads to decrease in both surface area and moderate acidity, therefore it is the cause of lower catalytic activity.展开更多
基金supported by grants from the National Natural Science Foundation of China(No.22272055)Scientific and Technological Project of Henan Province(No.222102240081)+1 种基金Science and Technology Planning Project of Anyang City(No.2022C01GX023)the support from Shanghai Synchrotron Radiation Facility(BL14B)for the sXRD experiments.
文摘The hard-to-remove lattice water has been regarded as a significant obstacle impeding the practical use of Prussian blue analogue cathodes for sodium-ion batteries.This work monitored the electrochemical evolution of a hydrated monoclinic sodium manganese hexacyanoferrate cathode by solid-state nuclear magnetic resonance(NMR).For the first time,we established a correlation between the chemical shifts of ^(23)Na NMR signals and the presence or absence of lattice water within this cathode.Through this method,we verified the electrochemical dehydration process that coincides with the merging of two redox platforms and a phase transformation in the initial cycles.Furthermore,we discovered that the lattice water is completely removed after several-day cell rest following a single activation cycle.
基金supported by the Research Program of the Science and Technology Department of Guizhou Province(Qiankehe Jichu[2019]1418)the Research Program of Talented Scholars of Guizhou Institute of Technology(XJGC20190965).
文摘In this context,the present study proposes the use of microwave irradiation to improve the dehydration rate and efficiency of strontium hydroxide octahydrate(Sr(OH)_(2)·8H_(2)O)without introducing contaminants.This study revealed that the use of microwave irradiation to dehydrate Sr(OH)_(2)·8H_(2)O is feasible and surprisingly efficient.The effects of this approach on important parameters were investigated using response surface methodology(RSM).The results revealed that the microwave dehydration process follows a linear polynomial model.In addition,compared with the heating time and material thickness,the microwave-assisted dehydration of Sr(OH)_(2)·8H_(2)O is sensitive to the microwave power and not to the material mass.The relative dehydration percentage reached 99.99%when heated in a microwave oven at 950Wfor just 3 min.In contrast,a relative dehydration percentage of 94.6%was reached when heated in an electric furnace at 180℃for 120 min.The XRD spectra also revealed that most of the Sr(OH)_(2)·8H_(2)O transformed into Sr(OH)_(2)after dehydration via microwave irradiation,whereas a significant portion of the Sr(OH)_(2)·H_(2)O remained after conventional electric dehydration.The experimental data were fitted and analyzed via the thin-layer drying dynamics model,and the results indicated that the dehydrating behavior of Sr(OH)_(2)·8H_(2)O could be well described by the Page model.
文摘Isosorbide is a novel bio-based material derived as a secondary dehydration product of sorbitol.This work focuses on the kinetics of sulfuric acid-catalyzed dehydration of sorbitol under conditions of nonconstant volume.Herein,the effects of stirring rate,catalyst dosage,reaction temperature,and reaction time on the dehydration reaction of sorbitol were investigated.The yield of isosorbide up to 77.13%was obtained after 1.5 h of reaction time under conditions of 2 kPa,1.0%(mass)catalyst dosage,and 413.15 K.Based on the sorbitol dehydration reaction mechanism and a simplified reaction network,a kinetic model was developed in this work.A good agreement was accomplished between kinetic modeling and experiments between 393.15 and 423.15 K.The fitting results indicate that side reactions with higher activation energies are more affected by reaction temperatures,and the main side reaction that influences the selectivity of isosorbide is the oligomerization reaction among the primary dehydration products of sorbitol.The model fitting of the catalyst amounts effect shows that the effective concentration of sulfuric acid would be reduced with the increase of dosage due to the molecular agglomeration effect.Hopefully,the kinetic experiments and modeling results obtained in this work will be helpful to the design and optimization of the industrial sorbitol dehydration process.
基金supported by the National Key Research and Development Program of China(2022YFD1400503)the National Natural Science Foundation of China(32102208)the Hebei Natural Science Foundation,China(C2022201042,C2021201052 and C2023201075).
文摘Drought events have become more severe under climate change,and this can pose a major threat to the survival of various organisms.The molecular mechanisms involved in dehydration resistance are not well known.Here,adults of the migratory locust,Locusta migratoria,were subjected to food-mediated dehydration,and adipokinetic hormone(AKH)signaling was found to play a key role in regulating dehydration resistance.Specifically,dehydration shortened the lifespan,increased the body weight loss,and reduced the water loss rate in adult locusts.Global transcriptome profiles revealed variations in tissue-specific gene expression between dehydration-resistant locusts and normal locusts.Importantly,dehydration selection and exposure induced prominent expression of AKH genes in the retrocerebral complex of adult locusts.Furthermore,individual knockdown of AKH1,AKH2,or AKH receptor(AKHR)accelerated water loss and shortened the lifespan of adult locusts under dehydration conditions,and trehalose supplementation ameliorated the negative effects caused by interference with AKH or AKHR.These findings demonstrated that AKH/AKHR signaling-dependent trehalose metabolism plays a crucial role in regulating locust dehydration resistance and thus provide novel insights into the regulatory mechanism underlying drought resistance.
文摘Significant waste resources are generated in the form of water-oil emulsions.These emulsions cannot be effectively destroyed on an industrial scale by traditional methods that rely on the settling of the aqueous phase,and therefore,they accumulate in large quantities.Thermomechanical dehydration,based on the evaporation of the water phase,presents a promising process for recycling such waste.However,within the framework of thermomechanical dehydration,the issue of optimizing energy costs for heating raw materials and controlling the water content in the product arises.Standard methods of determining water content under the boiling conditions of highly stable water-hydrocarbon emulsions are characterized by low efficiency,as they require constant sampling and the involvement of additional equipment and personnel.Consequently,this presents a challenge in predicting and creating an automated thermomechanical dehydration process.Therefore,dynamic curves depicting changes in the water content of these emulsions,depending on the temperature of the boiling liquid,have been obtained.It is proposed to determine the rate of temperature increase(dT/dt)of the boiling emulsion for continuous,real-time monitoring of the residual water content and for recording the moment of complete dehydration.Achieving a boiling emulsion temperature of 130-170℃(or higher)and/or the rate of temperature increase from 3.0 to 5.5(or above)indicates the complete dehydration of the emulsion.The proposed method can be implemented in any industrial or laboratory-scale unit for thermomechanical dehydration without significant capital costs.It is based on the use of simple devices consisting of temperature sensors and a computing unit for determining the temperature and rate of heating.
文摘In recent decades,MgSO_(4)·7H_(2)O(epsomite)has attracted significant attention as a promising thermochemical-based thermal energy storage material due to its high theoretical energy density,wide availability,and affordability.Despite extensive research efforts,progress in achieving high-energy density has been limited,primarily due to inadequate understanding of its reaction mechanisms and unfavorable dehydration/hydration kinetics.This study systematically investigated the hydration/dehydration kinetics and cyclability of MgSO_(4)·7H_(2)O.The results reveal that the dehydration process is influenced by the heating rate,with an optimal rate of 5℃/min,resulting in a seven-step MgSO_(4)·7H_(2)O dehydration process with a dehydration heat close to the theoretical value.The reaction kinetic analysis indicated that the rate of hydration was approximately 50%lower than that of dehydration.In addition,thermal cycling tests of MgSO_(4)·7H_(2)O under the conditions of this study(small sample size)indicated good cyclability,with hydration rates increasing with increasing cycling numbers up to approximately 10 cycles where level-off occurs.These results are consistent with scanning electron microscopy analyses,which revealed the formation of cracks and channels in the salt hydrate particles,facilitating mass transfer and improved kinetics.
基金Project(201011005-5)supported by the National Land and Resources Public Welfare Scientific Research Project of ChinaProject(41030426)supported by the National Natural Science Foundation of China+1 种基金Project(20095122110015)supported by Specialized Research Fund for the Doctoral Program of Higher Education of ChinaProject(2010-32)supported by Scientific Research Foundation of the Education Ministry for Returned Chinese Scholars,China
文摘The single phase La2（CO3）3·3.4H2 O was synthesized by hydrothermal method. The thermal decomposition and intermediates and final solid products of La2（CO3）3·3.4H2O from 30 to 1000 °C were characterized by XRD, FTIR and DTA-TG. The kinetics of dehydration of La2（CO3）3·3.4H2O in the temperature range of 30-366 °C was investigated under non-isothermal conditions. Flynn-Wall-Ozawa and Friedman isoconversion methods were used to calculate the activation energy and analyze the reaction steps; multivariate non-linear regression program was applied to determine the most probable mechanism and the kinetic parameters. The results show that the thermal dehydration of La2（CO3）3·3.4H2O is a kind of three-step competitive reaction, and controlled by an n-order initial reaction followed by n-order competitive reaction（FnFnFn model）. The activation energy matching with the most probable model is close to value obtained by Friedman method. The fitting curves match the original TG-DTG curves very well.
文摘The chlorophyll fluorescence kinetics of marine red alga Grateloupia turutunt Yamada, green alga Ulva pertusa Kjellm and brown alga Laminaria japonica Aresch during natural sustained dehydration were monitored and investigated. The pulse amplified modulation (PAM) system was used to analyze the distinct fluorescence parameters during thallus dehydration. Results proved that the fluorescence kinetics of different seaweed all showed three patterns of transformation with sustained water loss. These were: 1) peak kinetic pattern (at the early stage of dehydration fluorescence enhanced and quenched subsequently, representing a normal physiological state). 2) plateau kinetic pattern (with sustained water loss fluorescence enhanced continuously but quenching became slower, finally reaching its maximum). 3) Platform kinetic pattern (fluorescence fell and the shape of kinetic curve was similar to plateau kinetic pattern). A critical water content (CWC) could be found and defined as the percentage of water content just prior to the fluorescence drop and to be a significant physiological index for evaluation of plant drought tolerance. Once thallus water content became lower than this value the normal peak pattern can not be recovered even through rehydration, indicating an irreversible damage to the thylakoid membrane. The CWC value corresponding to different marine species were varied and negatively correlated with their desiccation tolerance, for example. Laminaria japonica had the highest CWC value (around 90%) and the lowest dehydration tolerance of the three. In addition, a fluorescence 'burst' was found only in red algae during rehydration. The different fluorescence parameters F-o, F-v and F-v, F-m were measured and compared during water loss. Both F-o and F-v increased in the first stage of dehydration but F-v/F-m. kept almost constant. So the immediate response of in vivo chlorophyll fluorescence to dehydration was an enhancement. Later with sustained dehydration F-o increased continuously while F-v decreased and tended to become smaller and smaller. The major changes in fluorescence (including fluorescence drop during dehydration and the burst during rehydration) were all attributed to the change in F-o instead of F-v This significance of F-o indicates that it is necessary to do more research on F-o as well as on its relationship with the state of thylakoid membrane.
基金supported by the National Natural Science Foundation of China(21376068)the China Postdoctoral Science Foundation(2016M592424)~~
文摘Iron exchanged ZSM-5 with Si/Al ratio from 25 to 300 prepared by three consecutive ion exchanges was used for the dehydration of ethanol to ethylene.The iron exchanged ZSM-5（Si/Al=25） catalyst with an iron content of 0.46 wt%gave 97%-99%yield of ethylene at 98%-99%conversion of ethanol at 260℃ and 0.81 h^-1 liquid hourly space velocity.The high performance was maintained for60 d on-stream.X-ray diffraction,Fourier transform infrared spectroscopy of pyridine adsorption,NH3 temperature-programmed desorption and diffuse reflectance UV-vis spectroscopy were used for catalyst characterization.Ion exchange with iron decreased the total acidity of the zeolite,especially the strong acid sites and Bronsted acid sites.The doped iron species were distributed over Fe-ZSM-5 as predominantly isolated Fe^3＋.Therefore,the catalytic performance for ethanol dehydration to ethylene was improved.
文摘Various ZSM-5 zeolites modified with alkali metals （Li, Na, K, Rb, and Cs） were prepared using ion exchange. The catalysts were used to enhance the catalytic dehydration of lactic acid （LA） to acrylic acid （AA）. The effects of cationic species on the structures and surface acid-base distributions of the ZSM-5 zeolites were investigated. The important factors that affect the catalytic performance were also identified. The modified ZSM-5 catalysts were characterized using X-ray diffraction, tempera- ture-programmed desorptions of NH3 and CO2, pyridine adsorption spectroscopy, and N2 adsorption to determine the crystal phase structures, surface acidities and basicities, nature of acid sites, specific surface areas, and pore volumes. The results show that the acid-base sites that are adjusted by alkali-metal species, particularly weak acid-base sites, are mainly responsible for the formation of AA. The KZSM-5 catalyst, in particular, significantly improved LA conversion and AA selectivity because of the synergistic effect of weak acid-base sites. The reaction was conducted at different reaction temperatures and liquid hourly space velocities （LHSVs） to understand the catalyst selectivity for AA and trends in byproduct formation. Approximately 98% LA conversion and 77% AA selectivity were achieved using the KZSM-5 catalyst under the optimum conditions （40 wt% LA aqueous solution, 365 ℃, and LHSV 2 h-1）.
文摘Formic acid （HCOOH） decomposition at Pt film electrode has been studied by electrochem- ical in situ FTIR spectroscopy under attenuated-total-reflection configuration, in order to clarify whether bridge-bonded formate （HCOOD） is the reactive intermediate for COad for-mation from HCOOH molecules. When switching from HCOOH-free solution to HCOOH- containing solution at constant potential （E=0.4 V vs. RHE）, we found that immediately upon solution switch COad formation rate is the highest, while surface coverage of formate is zero, then after COad formation rate decreases, while formate coverage reaches a steady state coverage quickly within ca. 1 s. Potential step experiment from E=0.75 V to 0.35 V, reveals that formate band intensity drops immediately right after the potential step, while the COad signal develops slowly with time. Both facts indicate that formate is not the reactive intermediate for formic acid dehydration to CO.
基金Supported by the National Natural Science Foundation of China(21490585,21606126)National High-tech R&D Program of China(2015AA03A602)a project funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)
文摘Pervaporation(including vapor permeation) is a kind of new membrane separation technology, possessing the advantages of high efficiency, energy saving and convenient operation. It has promising application in the separation and purification of organic solvents. Dehydration is an important step in the production and recovery of organic solvents. Zeolite membranes have attracted wide attention for pervaporation dehydration due to their high separation performance and good thermal/chemical stability. So far, zeolite membranes have been preliminarily industrialized for dehydration of organic solvents. This paper reviews the recent development of zeolite membranes for pervaporation dehydration, including mass transfer models, preparation and applications of zeolite membranes. The review also discusses the current industrial applications of zeolite membranes and their future development in pervaporation.
文摘A new type of dehydration unit for natural gas was briefly described and its basic structure and working principles were presented. An indoor test rig for testing the unit performance was set up and the experimental results were given. The results showed that the unit could attain a maximum dew point depression of about 20℃ without any need of external mechanical power and chemicals. The pressure loss ratio, shock wave and the flow rate had great influence on the dehydration characteristics. From the systematic analysis of the factors that affect the dehydration efficiency of the unit, the suggestions for improving the unit are put forward.
基金Supported by the National t）asic Research Program of China （2009CB623403）, the National High Technology Research and De velopment Program of China （2009AA034802）, the National Natural Science Foundation of China （20706030, U0834004）, the Science ＆ Technology Support Program （Industry） of Jiangsu Province of China （BE2008141）, the Natural Science Foundation of the Jiangsu Higher Education Institutions （09KJA530002） and 333 High-Level Personnel Training Project in Jiangsu Province. ＊＊ To whom correspondence should be addressed. E-mail： Xuehonggu@yahoo.com
文摘NaA zeolite membranes with 80 cm in length and 12.8 mm in outer diameter were prepared by our research group cooperating with Nanjing Jiusi Hi-Tech Co., China. The influence of dissolved inorganic salts and pH value in the feed of isopropanol （IPA） solution on NaA zeolite membranes was investigated. It was found that both factors exhibited strong influence on the stability of NaA zeolite membranes. A set of pretreatment steps such as pH adjustment and distillation of the IPA solution were proposed to improve stability for pervaporation dehydration. An industrial-scale pervaporation facility with 52 m2 membrane area was built to dehydrate IPA solution from industrial cephalosporin production. The facility was continuously operated at 368-378 K to dehydrate IPA solution from water mass content of 15%-20% to less than 2% with a feed flow rate of 400-500 L·h^-1 and an average water flux of 1-1.5 kg·m^-2·h-1. The successful application of this facility suggested a promising application of NaA zeolite mem-brane for IPA recovery from pharmaceutical production.
基金supported by the Inovation and Optimalization of Technologies for Natural Gas Dehydration(No.FR-TI1/173)
文摘This paper compares three methods for natural gas dehydration that are widely applied in industry：（1） absorption by triethylene glycol, （2） adsorption on solid desiccants and （3） condensation. A comparison is made according to their energy demand and suitability for use. The energy calculations are performed on a model where 105 Nm3/h water saturated natural gas is processed at 30 °C. The pressure of the gas varies from 7 to 20 MPa. The required outlet concentration of water in natural gas is equivalent to the dew point temperature of -10 °C at gas pressure of 4 MPa.
基金he Special Foundation for State Major Basic Research Program of China(2007CB707805,2004CCA05500)
文摘The production of acrylates from biomass-originated lactic acid is of extraordinary importance, to overcome the increasing worldwide shortage of petroleum. In this study, the catalytic dehydration of methyl lactate over a calcium sulfate catalyst, with various promoters, has been carried out to identify potential catalyst/promoter combinations for acrylate production. The best catalyst for methyl acrylate formation in this study has been calcium sulfate, with cupric sulfate and phosphates as promoters. The optimal mass ratio of m（CaSOa） ： m（CuSOa） ： m（Na2HPO4） ： m（KH2PO4） is 150.0 ： 13.8 ： 2.5 ： 1.2. Effects of carrier gas, reaction temperature, feed concentration as well as contact time on the dehydration of methyl lactate have been investigated. With nitrogen as a carrier gas, a combined yield of acrylic acid and methyl acrylate is 63.9% from 60% （by mass） methyl lactate at 400℃ with 7.7 seconds contact time.
基金the State Key Laboratory of Vanadium and Titanium Resources Comprehensive Utilization of China for its financial supportthe financial support of National Natural Science Foundation of China(Grant No.21576168)Science and Technology Cooperation Fund of Sichuan University-Panzhihua(No:2018CDPZH-23-SCU)。
文摘In order to concentrate the diluted sulfuric acid from the titanium dioxide(TiO2)production of sulphate process,a new concentration process was proposed by coupling chemical dehydration and multi-effect evaporation.The ferrous sulfate monohydrate(FeSO4·H2O),as the dehydrant,was added to the diluted sulfuric acid to form ferrous sulfate heptahydrate(FeSO4·7H2O)according to the H2SO4-FeSO4-H2O phase diagrams,which partially removes the water.This process was named as Chemical Dehydration Process.The residual water was further removed by two-effect evaporation and finally 70 wt%sulfuric acid was obtained.The FeSO4·H2O can be regenerated through drying and dehydration of FeSO4·7H2O.The results show that FeSO4·H2O is the most suitable dehydrant,the optimal reaction time of chemical dehydration process is 30 min,and low temperature is favorable for the dehydration reaction.45.17%of the entire removed water can be removed by chemical dehydration from the diluted sulfuric acid.This chemical dehydration process is also energy efficient with 24.76%saving compared with the direct evaporation process.Furthermore,51.21%of the FeSO4 dissolved originally in the diluted sulfuric acid are precipitated out during the chemical dehydration,which greatly reduces the solid precipitation and effectively alleviates the scaling in the subsequent multi-effect evaporation process.
基金supported by the National Natural Science Foundation of China (21173089 and 21373093)the Fundamental Research Funds for the Central Universities of China (2014ZZGH019)the Cooperative Innovation Center of Hubei Province
文摘Acid-catalyzed dehydration of alcohols has been widely employed for the synthesis of alkenes. However, activated alcohols when employed as substrates in dehydration reactions are often pla-gued by the lack of alkene selectivity. In this work, the reaction system can be significantly improved through enhancing the performance of Lewis acid catalysts in the dehydration of activated alcohols by combining with a Lewis base. Observations of the reaction mechanism revealed that the Lewis base component might have changed the reaction rate order. Although both the principal and side reaction rates decreased, the effect was markedly more observed on the latter reaction. Therefore, the selectivity of the dehydration reaction was improved. On the basis of this observation, a new route to synthesize 2-cinnamyl-1,3-dicarbonyl compounds was developed by using 2-aryl-3,4- di-hydropyran as a starting substrate in the presence of a Lewis acid/Lewis base combined catalyst system.
基金supported by the National Nature Science Foundation of China (No: 20976013)International Science & Technology Cooperation Program of China (No: 2012DFR40240)
文摘Micro-mesoporous composite molecular sieves H-ZSM-5/MCM-41 were prepared by the hydrothermal technique with alkali-treated H-ZSM-5zeolite as the source and characterized by scanning electron microscopy,transmission electron microscopy,energy dispersive spectroscopy,X-ray diffraction,N2 adsorption-desorption measurement and NH3 temperature-programmed desorption.The catalytic performances for the methanol dehydration to dimethyl ether over H-ZSM-5/MCM-41 were evaluated.Among these catalysts,H-ZSM-5/MCM-41 prepared with NaOH dosage (nNa/nSi) varying from 0.4 to 0.47 presented excellent catalytic activity with more than 80%methanol conversion and 100%dimethyl ether selectivity in a wide temperature range of 170—300℃,and H-ZSM-5/MCM-41 prepared with nNa/nSi=0.47 showed constant methanol conversion of about 88.7%,100% dimethyl ether selectivity and excellent lifetime at 220℃.The excellent catalytic performances were due to the highly active and uniform acidic sites and the hierarchical porosity in the micro-mesoporous composite molecular sieves.The catalytic mechanism of H-ZSM-5/MCM-41 for the methanol dehydration to dimethyl ether process was also discussed.
基金supported by the Petrochemical Research & Technology Company of National Petrochemical Company in Iran
文摘A series of nanocrystalline γ-alumina are synthesized by different procedures, namely, thermal decomposition method （sample A）, precipita-tion method （sample B） and sol-gel method using sucrose and hexadecyltrimethyl ammonium bromide （CTAB） as templates （samples C and D, respectively）. Textural and acidic properties of γ-alumina samples are characterized by XRD, N2 adsorption-desorption and NH3-TPD techniques. Vapor-phase dehydration of methanol into dimethyl ether is carried out over these samples. Among them, sample C shows the highest catalytic activity. NH3-TPD analysis reveals that the sample with smaller crystallite size possesses higher concentration of medium acidic sites and consequently higher catalytic activity. Thermal decomposition method leads to decrease in both surface area and moderate acidity, therefore it is the cause of lower catalytic activity.
