A floating horizontal-axis tidal current turbine(HATT)is an underwater power generation device where cavitation inevitably occurs on blade surfaces,severely affecting a turbine’s lifespan.Under wave action,these floa...A floating horizontal-axis tidal current turbine(HATT)is an underwater power generation device where cavitation inevitably occurs on blade surfaces,severely affecting a turbine’s lifespan.Under wave action,these floating turbines exhibit six degrees of freedom motion,potentially intensifying the cavitation on the blade surfaces.This study selects three types of oscillatory motions from the six degrees of freedom:roll,yaw,and pitch.Computational fluid dynamics(CFD)methods are used for numerical calculations,and transient simulations of multiphase flow are conducted on the basis of the Reynolds-Averaged Navier-Stokes(RANS)model.Research has revealed strong correlations between flow velocity,the blade tip speed ratio,and cavitation.During oscillatory motion,the motion period and amplitude also significantly impact cavitation.In roll motion,the cavitation rate can increase by up to 59%with decreasing period,whereas in pitch and yaw motions,the increases are 7.57 times and 36%larger,respectively.With an increase in amplitude during roll motion,the cavitation rate can increase by up to 1.08 times,whereas in pitch and yaw motions,the increases are 3.49 times and 45%,respectively.The cavitation rate on the blade surfaces is the highest in pitch motion,followed by roll and yaw motions.展开更多
The interaction between regular waves and an oscillating wave energy converter(WEC)in front of a vertical seawall is investigated using a 2D analytical model.A three-degree of freedom(DOF)WEC and a WEC hinged to the s...The interaction between regular waves and an oscillating wave energy converter(WEC)in front of a vertical seawall is investigated using a 2D analytical model.A three-degree of freedom(DOF)WEC and a WEC hinged to the seawall(constrained to pitch mode)are considered to examine the influence of the DOF of the WEC on the wave energy extraction performance.Results show that the piston-mode water resonance in the gap and the coupled WEC and water column resonant motion significantly influence the wave energy extraction efficiency.At low frequency,the case with a 3-DOF WEC has a broader high-efficiency bandwidth than that with a heaving WEC.However,3-DOF WEC exhibits worse performance at high frequencies.The frequency response of the wave energy capture width ratio(CWR)for the pitching WEC case shows a trimodal trend under the specified conditions.It showcases the best overall wave energy extraction performance in terms of the high-efficiency bandwidth.Furthermore,a parametric study indicates that the gap distance between the WEC and the seawall has tremendous effects on the CWR of both cases.As the position of the hinge point of the pitching WEC changes,the CWR at the low and high frequencies shows opposite trends.展开更多
BACKGROUND The degree of obstruction plays an important role in decision-making for obstructive colorectal cancer(OCRC).The existing assessment still relies on the colorectal obstruction scoring system(CROSS)which is ...BACKGROUND The degree of obstruction plays an important role in decision-making for obstructive colorectal cancer(OCRC).The existing assessment still relies on the colorectal obstruction scoring system(CROSS)which is based on a comprehensive analysis of patients’complaints and eating conditions.The data collection relies on subjective descriptions and lacks objective parameters.Therefore,a scoring system for the evaluation of computed tomography-based obstructive degree(CTOD)is urgently required for OCRC.AIM To explore the relationship between CTOD and CROSS and to determine whether CTOD could affect the short-term and long-term prognosis.METHODS Of 173 patients were enrolled.CTOD was obtained using k-means,the ratio of proximal to distal obstruction,and the proportion of nonparenchymal areas at the site of obstruction.CTOD was integrated with the CROSS to analyze the effect of emergency intervention on complications.Short-term and long-term outcomes were compared between the groups.RESULTS CTOD severe obstruction(CTOD grade 3)was an independent risk factor[odds ratio(OR)=3.390,95%confidence interval(CI):1.340-8.570,P=0.010]via multivariate analysis of short-term outcomes,while CROSS grade was not.In the CTOD-CROSS grade system,for the non-severe obstructive(CTOD 1-2 to CROSS 1-4)group,the complication rate of emergency interventions was significantly higher than that of non-emergency interventions(71.4%vs 41.8%,P=0.040).The postoperative pneumonia rate was higher in the emergency intervention group than in the non-severe obstructive group(35.7%vs 8.9%,P=0.020).However,CTOD grade was not an independent risk factor of overall survival and progression-free survival.CONCLUSION CTOD was useful in preoperative decision-making to avoid unnecessary emergency interventions and complications.展开更多
Aging in oak barrels is widely used in enology which could bring flavor changes and aromatic complexity to wines.In the present study,the aroma compounds were analyzed from the‘Merlot’dry red wines,which were fermen...Aging in oak barrels is widely used in enology which could bring flavor changes and aromatic complexity to wines.In the present study,the aroma compounds were analyzed from the‘Merlot’dry red wines,which were fermented in two types of fermenters(stainless steel tank and rotated oak barrel)and aged in six types of oak barrels(three geographic origins×two toasting degrees)for different time(0,3,6 and 9 months,respectively).Results showed that 30 volatiles were associated with barrels and increased during oak aging.The fermenters could influence the intensities of the toast,leathery,smoky,fruity,floral and caramel aromas.The concentration of whisky lactone,eugenol,cis-isoeugenol,and the intensities of the toast and spicy aromas were highest in the wines aged in American oak and were lowest in the wines aged in French oak barrels.The concentrations of guaiacol,syringol,trans-isoeugenol,furfural alcohol,vanilla,cis-whisky lactone enabled the medium toasting barrels to be distinguished from the light toasting ones.The compounds originating from the barrels could be used to distinguish the types of different barrels,but the other general grape-derived and fermentation-derived volatiles could not.The fermenters,oak species and toasting degrees of the barrels all had significant effects on the aroma profiles of the aged‘Merlot’dry red wines,but the influence of the geographic origin was not obvious.展开更多
The evaluation of sustainable land use is the key issue in the field of studying the sustainable land utilization. In general analysis, the sustainable land use is evaluated respectively from its ecological sustainabi...The evaluation of sustainable land use is the key issue in the field of studying the sustainable land utilization. In general analysis, the sustainable land use is evaluated respectively from its ecological sustainability, economic sustainability and social sustainability in China and other countries in recent years. Although this evaluation is an important work, it seems insufficient and hard to comprehensively reflect the whole degree of land use sustainability. Thus, to make up this deficiency, this paper brings forward the evaluation indexes, which make it possible to quantitatively reflect the whole degree of land use sustainability, namely, the concept of ＂degrees of overall land use sustainability＂ （Dos）, and research and measurement development of the method of and calculation in Dos. Taking the evaluation of the degree of land use sustainability in county regions of Yunnan Province as the actual example for analysis, results are basically as follows： 1） The degree of land use sustainability （Dos） is the ration index to organically and systematically integrate the degree of ecological friendliness （DeF）, the degree of economic viability （Dev） and the degree of social acceptability （Dsa）, able to comprehensively reflect the whole sustainability degree of regional land use 2） Based on the value of Dos, the grading system and standard for the sustainability of land use may be established and totally divided into five grades, namely, the high-degree sustainability, middle-degree sustainability, low-degree sustainability, conditional sustainability and non-sustainability. Meanwhile, the standard for distinguishing sustainability grades has also been confirmed so as to determine the nature of sustainability degrees in different grades. This makes the possibility for the combination of nature determination with ration in research result and provides with the scientific guideline and decision-making gist for better implementation of sustainable land use strategy. 3） The practice in evaluation of sustainability degree in county regional land use in Yunnan shows that the value of the degree of land use sustainability （Dos） of whole Yunnan Province is only 58.39, belonging to the grade of low-degree sustainability. Two thirds of counties in the whole province represent the grade of ＂conditional sustainability＂ and ＂non-sustainability＂ in the sustainability of land use. Among these counties, 11.11 % shows ＂non- sustainability＇. The lowest degree of land use sustainability appears especially in the middle plateau mountain region of Northeast Yunnan, where the value of Dos in most counties （districts） is below 40 %, belonging to the grade of ＂non-sustainability＂. The sustainability degree in the karst mountainous region in lower-middle plateau mountain region in Southeast Yunnan is generally low and the value of sustainability degree （Dos） in most of the counties （cities and districts） is below 55. The value of sustainability degree （Dos） in most of the counties （cities and districts） in the north, west, northwest and southwest parts of Yunnan is below 55. This article also analyzes the reasons of low degree of sustainability in land use in Yunnan and puts forward the countermeasures to increase the degree of sustainability in land use in the whole province.展开更多
Non-uniform linear array(NULA)configurations are well renowned due to their structural ability for providing increased degrees of freedom(DOF)and wider array aperture than uniform linear arrays(ULAs).These characteris...Non-uniform linear array(NULA)configurations are well renowned due to their structural ability for providing increased degrees of freedom(DOF)and wider array aperture than uniform linear arrays(ULAs).These characteristics play a significant role in improving the direction-of-arrival(DOA)estimation accuracy.However,most of the existing NULA geometries are primarily applicable to circular sources(CSs),while they limitedly improve the DOF and continuous virtual aperture for noncircular sources(NCSs).Toward this purpose,we present a triaddisplaced ULAs(Tdis-ULAs)configuration for NCS.The TdisULAs structure generally consists of three ULAs,which are appropriately placed.The proposed antenna array approach fully exploits the non-circular characteristics of the sources.Given the same number of elements,the Tdis-ULAs design achieves more DOF and larger hole-free co-array aperture than its sparse array competitors.Advantageously,the number of uniform DOF,optimal distribution of elements among the ULAs,and precise element positions are uniquely determined by the closed-form expressions.Moreover,the proposed array also produces a filled resulting co-array.Numerical simulations are conducted to show the performance advantages of the proposed Tdis-ULAs configuration over its counterpart designs.展开更多
This study introduces an advanced finite element model for the light weight deflectometer(LWD),which integrates contact mechanics with fully coupled models.By simulating LWD tests on granular soils at various saturati...This study introduces an advanced finite element model for the light weight deflectometer(LWD),which integrates contact mechanics with fully coupled models.By simulating LWD tests on granular soils at various saturation levels,the model accurately reflects the dependence of the LWD modulus on dry density,water content,and effective stress.This model addresses and overcomes the limitations of previous finite element models for this specific problem.Simultaneously,this research presents the first experimentally validated fully coupled contact impact model.Furthermore,the research provides a comparative assessment of elastoplastic and nonlinear elastic models and contrasts an enriched node-tosegment method(developed in this study)with the more precise mortar technique for contact mechanics.These comparisons reveal unique advantages and challenges for each method.Moreover,the study underscores the importance of careful application of the LWD modulus,emphasising the need for sophisticated tools to interpret soil behaviour accurately.展开更多
The degree of processing is rarely considered an independent factor in the health effects of fruit juices and beverages(FJBs)consumption.In fact,the consumption of ultra-processed foods has been shown to pose health r...The degree of processing is rarely considered an independent factor in the health effects of fruit juices and beverages(FJBs)consumption.In fact,the consumption of ultra-processed foods has been shown to pose health risks.In this study,we first integrated 4 systems used to classify the degree of food processing and then classified FJBs into three major categories,low(minimal),moderate and high.Second,we compared the differences in attitudes towards FJBs in dietary guidelines.Third,we integrated the results of existing epidemiological surveys,randomized controlled trials,and animal experiments to explore the health risks associated with consuming FJBs.Deepening the processing of FJBs has been found to lead to an increased risk of diseases.Dietary pattern,nutrients,addition agents and consumer preferences may be influential factors.Finally,we investigated whether there were any changes in the health benefits of 100%fruit juices produced by different processing methods.In conclusion,minimally/moderately processed 100%fruit juices provide more health benefits than highly processed fruit beverages.The results support the need to consider the extent of FJBs processing in future studies to adjust official nutritional recommendations for beverage consumption.展开更多
[Objective] In order to study the relations among different positions, degrees of substitution and antioxidant ability. [Method] N, O-carboxymethyl chitosan （NOA, NOB and NOC）with various degrees of substitution （D...[Objective] In order to study the relations among different positions, degrees of substitution and antioxidant ability. [Method] N, O-carboxymethyl chitosan （NOA, NOB and NOC）with various degrees of substitution （DS）were obtained by etherizing chito-oligosacchaside. Their structure and substituted degree were characterized and their antioxldant activity to·OH was evaluated. [ Result] The IC50 s of NOA ,NOB and NOC were 0.15 ,0. 29 ,0. 23 mg/ml while their DSs of -NH2 position（DSN） were 0.51,0.29 and 0.38 and DSo were 0. 74 ,0. 84 ,0. 97respectively.[ Conclusion] With the increase of DSN ,antioxidant activity of N,O-carboxymethyl chitosan oligosaccharide to·OH was up.展开更多
Increasing degrees of freedom(DOFs)is a useful way to raise the power capture efficiency of oscillating wave energy converters.Thus,this study proposes a buoy with three DOFs,which are surge,heave,and pitch.The hydrod...Increasing degrees of freedom(DOFs)is a useful way to raise the power capture efficiency of oscillating wave energy converters.Thus,this study proposes a buoy with three DOFs,which are surge,heave,and pitch.The hydrodynamic performance and power capture efficiency of the buoy is physically modeled.Amplitudes of unidirectional and coupled motions are compared to analyze the interaction effect between freedoms under conditions with and without power take-off damping.The capture width ratio and corresponding growth rates are also calculated.Results show that the buoy makes a periodic sinusoidal(or approximate)movement in every DOF.Coupling effect can cause an increase in the amplitude in one DOF and a decrease in the amplitudes of the others.This phenomenon shows that the kinematic energy of the buoy redistributes to all DOFs compared with the unidirectional conditions.Adding DOFs can improve the power absorption of the buoy in most cases,but the number of DOFs is not the more the better.展开更多
A modified two-degrees-of-freedom( M-TDOF) internal model control( IMC) method is proposed for non-square systems with multiple time delays and right-half-plane( RHP) zeros. In this method,pseudo-inverse is introduced...A modified two-degrees-of-freedom( M-TDOF) internal model control( IMC) method is proposed for non-square systems with multiple time delays and right-half-plane( RHP) zeros. In this method,pseudo-inverse is introduced to design the internal model controller,and a desired closed-loop transfer function is designed to eliminate the unrealizable factors of the derived controller. In addition,set-point tracking and load-disturbance rejection of each process are separately controlled by two controllers. The simulation results show that in addition to high decoupling performance and robustness,the proposed control method also effectively improves loaddisturbance rejection and simultaneously optimizes the input tracking performance and disturbance rejection performance by selecting the parameters of controllers. Furthermore,the higher tolerance of model mismatch is achieved in this paper.展开更多
Based on support vector machines, three modeling methods, i.e., white-box modeling, grey-box modeling and black-box modeling of ship manoeuvring motion in 4 degrees of freedom are investigated. With the whole-ship mat...Based on support vector machines, three modeling methods, i.e., white-box modeling, grey-box modeling and black-box modeling of ship manoeuvring motion in 4 degrees of freedom are investigated. With the whole-ship mathematical model for ship manoeuvring motion, in which the hydrodynamic coefficients are obtained from roll planar motion mechanism test, some zigzag tests and turning circle manoeuvres are simulated. In the white-box modeling and grey-box modeling, the training data taken every 5 s from the simulated 20°/20° zigzag test are used, while in the black-box modeling, the training data taken every 5 s from the simulated 15°/15°, 20°/20° zigzag tests and 15°, 25° turning manoeuvres are used; and the trained support vector machines are used to predict the whole 20°/20° zigzag test. Comparisons between the simulated and predicted 20°/20° zigzag tests show good predictive ability of the proposed methods. Besides, all mathematical models obtained by the proposed modeling methods are used to predict the 10°/10° zigzag test and 35° turning circle manoeuvre, and the predicted results are compared with those of simulation tests to demonstrate the good generalization performance of the mathematical models. Finally, the proposed modeling methods are analyzed and compared with each other in aspects of application conditions, prediction accuracy and computation speed. The appropriate modeling method can be chosen according to the intended use of the mathematical models and the available data needed for system identification.展开更多
High degrees of freedom(DOF)for K^(+)movement in the electrolytes is desirable,because the resulting high ionic conductivity helps improve potassium-ion batteries,yet requiring support from highly free and flammable o...High degrees of freedom(DOF)for K^(+)movement in the electrolytes is desirable,because the resulting high ionic conductivity helps improve potassium-ion batteries,yet requiring support from highly free and flammable organic solvent molecules,seriously affecting battery safety.Here,we develop a K^(+)flux rectifier to trim K ion’s DOF to 1 and improve electrochemical properties.Although the ionic conductivity is compromised in the K^(+)flux rectifier,the overall electrochemical performance of PIBs was improved.An oxidation stability improvement from 4.0 to 5.9 V was realized,and the formation of dendrites and the dissolution of organic cathodes were inhibited.Consequently,the K||K cells continuously cycled over 3,700 h;K||Cu cells operated stably over 800 cycles with the Coulombic efficiency exceeding 99%;and K||graphite cells exhibited high-capacity retention over 74.7%after 1,500 cycles.Moreover,the 3,4,9,10-perylenetetracarboxylic diimide organic cathodes operated for more than 2,100 cycles and reached year-scale-cycling time.We fabricated a 2.18 Ah pouch cell with no significant capacity fading observed after 100 cycles.展开更多
The two-rotational-degrees-of-freedom（2R） parallel mechanism（PM） with two continuous rotational axes（CRAs） has a simple kinematic model.It is therefore easy to implement trajectory planning,parameter calibration...The two-rotational-degrees-of-freedom（2R） parallel mechanism（PM） with two continuous rotational axes（CRAs） has a simple kinematic model.It is therefore easy to implement trajectory planning,parameter calibration,and motion control,which allows for a variety of application prospects.However,no systematic analysis on structural constraints of the 2R-PM with two CRAs has been performed,and there are only a few types of 2R-PM with two CRAs.Thus,a theory regarding the type synthesis of the 2R-PM with two CRAs is systematically established.First,combining the theories of reciprocal screw and space geometry,the spatial arrangement relationships of the constraint forces applied to the moving platform by the branches are explored,which give the 2R-PM two CRAs.The different distributions of the constraint forces in each branch are also studied.On the basis of the obtained structural constraints of branches,and considering the geometric relationships of constraint forces in each branch,the appropriate kinematic chains are constructed.Through the reasonable configuration of branch kinematic chains corresponding to every structural constraint,a series of new 2R-PMs with two CRAs are finally obtained.展开更多
A new kind of quadrilateral assumed stress hy- brid membrane element with drilling degrees of freedom and a traction-free inclined side has been developed based on an extended Hellinger-Reissner principle which is est...A new kind of quadrilateral assumed stress hy- brid membrane element with drilling degrees of freedom and a traction-free inclined side has been developed based on an extended Hellinger-Reissner principle which is established by expanding the essential terms of the assumed stress field as polynomials in the natural coordinates of the element. The homogeneous equilibrium equations are imposed in a variational sense through the internal displacements which are also expanded in the natural coordinates, while the tractionfree conditions along the inclined side are satisfied exactly. The use of such special element in the finite element solution is shown to be highly accurate when only a very coarse element mesh is used for plates with V-shaped rounded notches or inclined sides.展开更多
The current research of supporting and transmission system in flywheel energy storage system(FESS) focuses on the low consumption design. However, friction loss is a non-negligible factor in the high-speed but lightwe...The current research of supporting and transmission system in flywheel energy storage system(FESS) focuses on the low consumption design. However, friction loss is a non-negligible factor in the high-speed but lightweight FESS energy and momentum storage with mechanical-type supporting system. In order to realize the support system without mechanical loss and to maximize the e ciency of the flywheel battery, a permanent magnet biased magnetic bearings(PMBMB) is applied to the FESS with the advantages of low loss, high critical speed, flexible controllability and compact structure. In this frame, the relevant research of three degrees of freedom(3-DOF) PMBMB for a new type FESS is carried out around the working principle, structural composition, coupling characteristics analysis, mathematical model, and structural design. In order to verify the performance of the 3-DOF PMBMB, the radial force mathematical model and the coupling determination equations of radial two DOF are calculated according to an equivalent magnetic circuit, and radial–axial coupling is analyzed through finite element analysis. Moreover, a control system is presented to solve the control problems in practical applications. The rotor returns to the balanced position in 0.05 s and maintains stable suspension. The displacement fluctuation is approximately 40 μm in the y direction and 30 μm in the x direction. Test results indicate that the dynamic rotor of the proposed flywheel energy storage system with PMBMB has excellent characteristics, such as good start-of-suspension performance and stable suspension characteristics. The proposed research provides the instruction to design and control a low loss support system for FESS.展开更多
Asymmetrically modified Janus graphene oxide(JGO)has attracted great attention due to its unique physical chemistry properties and wide applications.The modification degree of Janus nanosheets inevitably affects their...Asymmetrically modified Janus graphene oxide(JGO)has attracted great attention due to its unique physical chemistry properties and wide applications.The modification degree of Janus nanosheets inevitably affects their interfacial activity,which is essential for their performances in enhanced oil recovery(EOR).In this study,the interfacial properties of Janus graphene oxide(JGO)with various modification degrees at liquid-liquid and liquid-solid interfaces were systematically evaluated via the measurements of interfacial tension(IFT),dilatational modulus,contact angle,and EOR efficiency was further assessed by core flooding tests.It is found that JGO-5 with higher modification degree exhibits the greater ability to reduce IFT(15.16 mN/m)and dilatational modulus(26 mN/m).Furthermore,JGO can construct interfacial and climbing film with the assistance of hydrodynamic power to effectively detach the oil from the rock surface and greatly enhance oil recovery.Moderately modified JGO-2 can highly improve recovery of residual crude oil(11.53%),which is regarded as the promising EOR agent in practical application.The present study firstly focuses on the effects of modification degrees on the JGO interfacial properties and proposes diverse EOR mechanisms for JGO with different modification degrees.展开更多
When performing operation tasks, the interaction between a flexible manipulator and a grasped object usually results in an impact. In this paper, a new way is suggested to alleviate impact vibration of a flexible mani...When performing operation tasks, the interaction between a flexible manipulator and a grasped object usually results in an impact. In this paper, a new way is suggested to alleviate impact vibration of a flexible manipulator via its structural characteristic when capturing a moving object. Controllable local degrees of freedom are introduced to the topological structure of the flexible manipulator, and used as an effective tool to combat impact vibration through dynamic coupling. A corresponding method is put forward to reduce impact vibration responses of the flexible manip- ulator via the controllable local degrees of freedom. By planning motion of the controllable local degrees of freedom, appropriate control force can be constructed to increase the modal damping and stiffness and eliminate the exciting force simultaneously, thereby reducing impact vibration responses of the flexible manipulator. Simulations are conducted and results are shown to prove the presented method.展开更多
The behavior of vortex-induced vibration of a two-degree-of-freedom cylinder near a deformable wall in steady flow is investigated experimentally. The typical phenomenon of the two-degree-of-freedom cylinder＇s VIV is...The behavior of vortex-induced vibration of a two-degree-of-freedom cylinder near a deformable wall in steady flow is investigated experimentally. The typical phenomenon of the two-degree-of-freedom cylinder＇s VIV is discussed. The influences of initial gap between the cylinder and the wall on the dynamic responses of the cylinder are analyzed. The comparison is made about dynamic responses of the cylinder with one and two degrees of freedom. Experimental results show that the vibration of the cylinder near a deformable wall with a small value of initial gap-to-diameter ratios can generally be divided into two phases. The initial gap-to-diameter ratios have a noticeable influence on the occurrence of transverse vibration. The transverse maximum amplitude of the cylinder with two degrees of freedom is larger than that of the cylinder with one degree of freedom under the condition with the same values of other parameters. However, the vibration frequency of the cylinder for the two degrees of freedom case is smaller than that for the one degree of freedom case at the same value of Vr number展开更多
A novel compliant mechanism with RPR degrees of freedom(DOF)is proposed where R and P represent rotation and translation DOFs,respectively.The proposed compliant mechanism is obtained from dimension synthesizing a 2-R...A novel compliant mechanism with RPR degrees of freedom(DOF)is proposed where R and P represent rotation and translation DOFs,respectively.The proposed compliant mechanism is obtained from dimension synthesizing a 2-RPU-UPR rigid parallel mechanism with the method of optimization of motion/force transfer characteristic.R,P and U represent rotation,translation and universal pairs,respectively.Firstly,inverse kinematics and Jacobian matrix are analyzed for the dimensional synthesis.Then,output transmission indexes of branches in the parallel mechanism are given.Dimensional synthesis is completed based on the normalized design parameter.And optimization of flexure joints based on constrained energy is carried out.Afterwards,the novel compliant mechanism is obtained by direct replacing method.Mechanical model of the compliant mechanism including static stiffness and input stiffness is built based on the pseudo-rigid body modeling method and virtual work principle.Finally,FEA simulation by Ansys Workbench is carried out to verify DOF,effectiveness of the dimension synthesis,and compliant model.Optimization of motion/force transfer characteristic is first applied for the design of compliant mechanisms to suppress drift of rotation axis in the paper.展开更多
基金supported by the National Natural Science Foundation of China(Grant No.52171261).
文摘A floating horizontal-axis tidal current turbine(HATT)is an underwater power generation device where cavitation inevitably occurs on blade surfaces,severely affecting a turbine’s lifespan.Under wave action,these floating turbines exhibit six degrees of freedom motion,potentially intensifying the cavitation on the blade surfaces.This study selects three types of oscillatory motions from the six degrees of freedom:roll,yaw,and pitch.Computational fluid dynamics(CFD)methods are used for numerical calculations,and transient simulations of multiphase flow are conducted on the basis of the Reynolds-Averaged Navier-Stokes(RANS)model.Research has revealed strong correlations between flow velocity,the blade tip speed ratio,and cavitation.During oscillatory motion,the motion period and amplitude also significantly impact cavitation.In roll motion,the cavitation rate can increase by up to 59%with decreasing period,whereas in pitch and yaw motions,the increases are 7.57 times and 36%larger,respectively.With an increase in amplitude during roll motion,the cavitation rate can increase by up to 1.08 times,whereas in pitch and yaw motions,the increases are 3.49 times and 45%,respectively.The cavitation rate on the blade surfaces is the highest in pitch motion,followed by roll and yaw motions.
基金supported by the Key R&D Program of Shandong Province,China(No.2021ZLGX04)the National Natural Science Foundation of China(No.52171284)。
文摘The interaction between regular waves and an oscillating wave energy converter(WEC)in front of a vertical seawall is investigated using a 2D analytical model.A three-degree of freedom(DOF)WEC and a WEC hinged to the seawall(constrained to pitch mode)are considered to examine the influence of the DOF of the WEC on the wave energy extraction performance.Results show that the piston-mode water resonance in the gap and the coupled WEC and water column resonant motion significantly influence the wave energy extraction efficiency.At low frequency,the case with a 3-DOF WEC has a broader high-efficiency bandwidth than that with a heaving WEC.However,3-DOF WEC exhibits worse performance at high frequencies.The frequency response of the wave energy capture width ratio(CWR)for the pitching WEC case shows a trimodal trend under the specified conditions.It showcases the best overall wave energy extraction performance in terms of the high-efficiency bandwidth.Furthermore,a parametric study indicates that the gap distance between the WEC and the seawall has tremendous effects on the CWR of both cases.As the position of the hinge point of the pitching WEC changes,the CWR at the low and high frequencies shows opposite trends.
基金the Youth Foundation of Fujian Provincial Health Commission,No.2021QNA014the Construction Project of Fujian Province Minimally Invasive Medical Center,No.[2021]76.
文摘BACKGROUND The degree of obstruction plays an important role in decision-making for obstructive colorectal cancer(OCRC).The existing assessment still relies on the colorectal obstruction scoring system(CROSS)which is based on a comprehensive analysis of patients’complaints and eating conditions.The data collection relies on subjective descriptions and lacks objective parameters.Therefore,a scoring system for the evaluation of computed tomography-based obstructive degree(CTOD)is urgently required for OCRC.AIM To explore the relationship between CTOD and CROSS and to determine whether CTOD could affect the short-term and long-term prognosis.METHODS Of 173 patients were enrolled.CTOD was obtained using k-means,the ratio of proximal to distal obstruction,and the proportion of nonparenchymal areas at the site of obstruction.CTOD was integrated with the CROSS to analyze the effect of emergency intervention on complications.Short-term and long-term outcomes were compared between the groups.RESULTS CTOD severe obstruction(CTOD grade 3)was an independent risk factor[odds ratio(OR)=3.390,95%confidence interval(CI):1.340-8.570,P=0.010]via multivariate analysis of short-term outcomes,while CROSS grade was not.In the CTOD-CROSS grade system,for the non-severe obstructive(CTOD 1-2 to CROSS 1-4)group,the complication rate of emergency interventions was significantly higher than that of non-emergency interventions(71.4%vs 41.8%,P=0.040).The postoperative pneumonia rate was higher in the emergency intervention group than in the non-severe obstructive group(35.7%vs 8.9%,P=0.020).However,CTOD grade was not an independent risk factor of overall survival and progression-free survival.CONCLUSION CTOD was useful in preoperative decision-making to avoid unnecessary emergency interventions and complications.
基金the financial support received from The Key Project of R&D Program of Ningxia Hui Autonomous Region,China(2022BBF01003)China Agriculture Research System of MOF and MARA(CARS-29).
文摘Aging in oak barrels is widely used in enology which could bring flavor changes and aromatic complexity to wines.In the present study,the aroma compounds were analyzed from the‘Merlot’dry red wines,which were fermented in two types of fermenters(stainless steel tank and rotated oak barrel)and aged in six types of oak barrels(three geographic origins×two toasting degrees)for different time(0,3,6 and 9 months,respectively).Results showed that 30 volatiles were associated with barrels and increased during oak aging.The fermenters could influence the intensities of the toast,leathery,smoky,fruity,floral and caramel aromas.The concentration of whisky lactone,eugenol,cis-isoeugenol,and the intensities of the toast and spicy aromas were highest in the wines aged in American oak and were lowest in the wines aged in French oak barrels.The concentrations of guaiacol,syringol,trans-isoeugenol,furfural alcohol,vanilla,cis-whisky lactone enabled the medium toasting barrels to be distinguished from the light toasting ones.The compounds originating from the barrels could be used to distinguish the types of different barrels,but the other general grape-derived and fermentation-derived volatiles could not.The fermenters,oak species and toasting degrees of the barrels all had significant effects on the aroma profiles of the aged‘Merlot’dry red wines,but the influence of the geographic origin was not obvious.
文摘The evaluation of sustainable land use is the key issue in the field of studying the sustainable land utilization. In general analysis, the sustainable land use is evaluated respectively from its ecological sustainability, economic sustainability and social sustainability in China and other countries in recent years. Although this evaluation is an important work, it seems insufficient and hard to comprehensively reflect the whole degree of land use sustainability. Thus, to make up this deficiency, this paper brings forward the evaluation indexes, which make it possible to quantitatively reflect the whole degree of land use sustainability, namely, the concept of ＂degrees of overall land use sustainability＂ （Dos）, and research and measurement development of the method of and calculation in Dos. Taking the evaluation of the degree of land use sustainability in county regions of Yunnan Province as the actual example for analysis, results are basically as follows： 1） The degree of land use sustainability （Dos） is the ration index to organically and systematically integrate the degree of ecological friendliness （DeF）, the degree of economic viability （Dev） and the degree of social acceptability （Dsa）, able to comprehensively reflect the whole sustainability degree of regional land use 2） Based on the value of Dos, the grading system and standard for the sustainability of land use may be established and totally divided into five grades, namely, the high-degree sustainability, middle-degree sustainability, low-degree sustainability, conditional sustainability and non-sustainability. Meanwhile, the standard for distinguishing sustainability grades has also been confirmed so as to determine the nature of sustainability degrees in different grades. This makes the possibility for the combination of nature determination with ration in research result and provides with the scientific guideline and decision-making gist for better implementation of sustainable land use strategy. 3） The practice in evaluation of sustainability degree in county regional land use in Yunnan shows that the value of the degree of land use sustainability （Dos） of whole Yunnan Province is only 58.39, belonging to the grade of low-degree sustainability. Two thirds of counties in the whole province represent the grade of ＂conditional sustainability＂ and ＂non-sustainability＂ in the sustainability of land use. Among these counties, 11.11 % shows ＂non- sustainability＇. The lowest degree of land use sustainability appears especially in the middle plateau mountain region of Northeast Yunnan, where the value of Dos in most counties （districts） is below 40 %, belonging to the grade of ＂non-sustainability＂. The sustainability degree in the karst mountainous region in lower-middle plateau mountain region in Southeast Yunnan is generally low and the value of sustainability degree （Dos） in most of the counties （cities and districts） is below 55. The value of sustainability degree （Dos） in most of the counties （cities and districts） in the north, west, northwest and southwest parts of Yunnan is below 55. This article also analyzes the reasons of low degree of sustainability in land use in Yunnan and puts forward the countermeasures to increase the degree of sustainability in land use in the whole province.
基金supported by the National Natural Science Foundation of China(62031017,61971221)the Fundamental Research Funds for the Central Universities of China(NP2020104)。
文摘Non-uniform linear array(NULA)configurations are well renowned due to their structural ability for providing increased degrees of freedom(DOF)and wider array aperture than uniform linear arrays(ULAs).These characteristics play a significant role in improving the direction-of-arrival(DOA)estimation accuracy.However,most of the existing NULA geometries are primarily applicable to circular sources(CSs),while they limitedly improve the DOF and continuous virtual aperture for noncircular sources(NCSs).Toward this purpose,we present a triaddisplaced ULAs(Tdis-ULAs)configuration for NCS.The TdisULAs structure generally consists of three ULAs,which are appropriately placed.The proposed antenna array approach fully exploits the non-circular characteristics of the sources.Given the same number of elements,the Tdis-ULAs design achieves more DOF and larger hole-free co-array aperture than its sparse array competitors.Advantageously,the number of uniform DOF,optimal distribution of elements among the ULAs,and precise element positions are uniquely determined by the closed-form expressions.Moreover,the proposed array also produces a filled resulting co-array.Numerical simulations are conducted to show the performance advantages of the proposed Tdis-ULAs configuration over its counterpart designs.
基金This research work is part of a research project(Grant No.IH18.03.1)sponsored by the SPARC Hub at the Department of Civil Engineering,Monash University funded by the Australian Research Council(ARC)Industrial Transformation Research Hub(ITRH)Scheme(Grant No.IH180100010).
文摘This study introduces an advanced finite element model for the light weight deflectometer(LWD),which integrates contact mechanics with fully coupled models.By simulating LWD tests on granular soils at various saturation levels,the model accurately reflects the dependence of the LWD modulus on dry density,water content,and effective stress.This model addresses and overcomes the limitations of previous finite element models for this specific problem.Simultaneously,this research presents the first experimentally validated fully coupled contact impact model.Furthermore,the research provides a comparative assessment of elastoplastic and nonlinear elastic models and contrasts an enriched node-tosegment method(developed in this study)with the more precise mortar technique for contact mechanics.These comparisons reveal unique advantages and challenges for each method.Moreover,the study underscores the importance of careful application of the LWD modulus,emphasising the need for sophisticated tools to interpret soil behaviour accurately.
基金funded by the National Natural Science Foundation Program of China(31901707)the 2115 Talent Development Program of China Agricultural University。
文摘The degree of processing is rarely considered an independent factor in the health effects of fruit juices and beverages(FJBs)consumption.In fact,the consumption of ultra-processed foods has been shown to pose health risks.In this study,we first integrated 4 systems used to classify the degree of food processing and then classified FJBs into three major categories,low(minimal),moderate and high.Second,we compared the differences in attitudes towards FJBs in dietary guidelines.Third,we integrated the results of existing epidemiological surveys,randomized controlled trials,and animal experiments to explore the health risks associated with consuming FJBs.Deepening the processing of FJBs has been found to lead to an increased risk of diseases.Dietary pattern,nutrients,addition agents and consumer preferences may be influential factors.Finally,we investigated whether there were any changes in the health benefits of 100%fruit juices produced by different processing methods.In conclusion,minimally/moderately processed 100%fruit juices provide more health benefits than highly processed fruit beverages.The results support the need to consider the extent of FJBs processing in future studies to adjust official nutritional recommendations for beverage consumption.
基金Supported by Shanghai Leading Academic Discipline(Project No.T1102)Shanghai Commission of Education Scientific Research Project(07zz134)~~
文摘[Objective] In order to study the relations among different positions, degrees of substitution and antioxidant ability. [Method] N, O-carboxymethyl chitosan （NOA, NOB and NOC）with various degrees of substitution （DS）were obtained by etherizing chito-oligosacchaside. Their structure and substituted degree were characterized and their antioxldant activity to·OH was evaluated. [ Result] The IC50 s of NOA ,NOB and NOC were 0.15 ,0. 29 ,0. 23 mg/ml while their DSs of -NH2 position（DSN） were 0.51,0.29 and 0.38 and DSo were 0. 74 ,0. 84 ,0. 97respectively.[ Conclusion] With the increase of DSN ,antioxidant activity of N,O-carboxymethyl chitosan oligosaccharide to·OH was up.
基金the support of the National Key R&D Program of China (No. 2018YFB1501900)the National Natural Science Fund of China (No. 41706100)+3 种基金the Shandong Provincial Natural Science Key Basic Program (No. ZR2017ZA 0202)the Special Projects for Marine Renewable Energy (No. GHME2016YY02)the Shandong Provincial Key Laboratory of Ocean Engineeringthe Qingdao Municipal Key Laboratory of Ocean Renewable Energy
文摘Increasing degrees of freedom(DOFs)is a useful way to raise the power capture efficiency of oscillating wave energy converters.Thus,this study proposes a buoy with three DOFs,which are surge,heave,and pitch.The hydrodynamic performance and power capture efficiency of the buoy is physically modeled.Amplitudes of unidirectional and coupled motions are compared to analyze the interaction effect between freedoms under conditions with and without power take-off damping.The capture width ratio and corresponding growth rates are also calculated.Results show that the buoy makes a periodic sinusoidal(or approximate)movement in every DOF.Coupling effect can cause an increase in the amplitude in one DOF and a decrease in the amplitudes of the others.This phenomenon shows that the kinematic energy of the buoy redistributes to all DOFs compared with the unidirectional conditions.Adding DOFs can improve the power absorption of the buoy in most cases,but the number of DOFs is not the more the better.
基金Sponsored by the Fundamental Research Funds for the Central Universities(Grant No.N110304008)the National Natural Science Foundation of China(Grant No.61374137)
文摘A modified two-degrees-of-freedom( M-TDOF) internal model control( IMC) method is proposed for non-square systems with multiple time delays and right-half-plane( RHP) zeros. In this method,pseudo-inverse is introduced to design the internal model controller,and a desired closed-loop transfer function is designed to eliminate the unrealizable factors of the derived controller. In addition,set-point tracking and load-disturbance rejection of each process are separately controlled by two controllers. The simulation results show that in addition to high decoupling performance and robustness,the proposed control method also effectively improves loaddisturbance rejection and simultaneously optimizes the input tracking performance and disturbance rejection performance by selecting the parameters of controllers. Furthermore,the higher tolerance of model mismatch is achieved in this paper.
基金financially supported by the National Natural Science Foundation of China(Grant No.51279106)the Special Research Fund for the Doctoral Program of Higher Education of China(Grant No.20110073110009)
文摘Based on support vector machines, three modeling methods, i.e., white-box modeling, grey-box modeling and black-box modeling of ship manoeuvring motion in 4 degrees of freedom are investigated. With the whole-ship mathematical model for ship manoeuvring motion, in which the hydrodynamic coefficients are obtained from roll planar motion mechanism test, some zigzag tests and turning circle manoeuvres are simulated. In the white-box modeling and grey-box modeling, the training data taken every 5 s from the simulated 20°/20° zigzag test are used, while in the black-box modeling, the training data taken every 5 s from the simulated 15°/15°, 20°/20° zigzag tests and 15°, 25° turning manoeuvres are used; and the trained support vector machines are used to predict the whole 20°/20° zigzag test. Comparisons between the simulated and predicted 20°/20° zigzag tests show good predictive ability of the proposed methods. Besides, all mathematical models obtained by the proposed modeling methods are used to predict the 10°/10° zigzag test and 35° turning circle manoeuvre, and the predicted results are compared with those of simulation tests to demonstrate the good generalization performance of the mathematical models. Finally, the proposed modeling methods are analyzed and compared with each other in aspects of application conditions, prediction accuracy and computation speed. The appropriate modeling method can be chosen according to the intended use of the mathematical models and the available data needed for system identification.
基金supported by the National Natural Science Foundation of China(Nos.U20A20247 and 51922038).A.M.R.acknowledges the seed funding provided by the R.A.Bowen Endowed Professorship funds at Clemson University.
文摘High degrees of freedom(DOF)for K^(+)movement in the electrolytes is desirable,because the resulting high ionic conductivity helps improve potassium-ion batteries,yet requiring support from highly free and flammable organic solvent molecules,seriously affecting battery safety.Here,we develop a K^(+)flux rectifier to trim K ion’s DOF to 1 and improve electrochemical properties.Although the ionic conductivity is compromised in the K^(+)flux rectifier,the overall electrochemical performance of PIBs was improved.An oxidation stability improvement from 4.0 to 5.9 V was realized,and the formation of dendrites and the dissolution of organic cathodes were inhibited.Consequently,the K||K cells continuously cycled over 3,700 h;K||Cu cells operated stably over 800 cycles with the Coulombic efficiency exceeding 99%;and K||graphite cells exhibited high-capacity retention over 74.7%after 1,500 cycles.Moreover,the 3,4,9,10-perylenetetracarboxylic diimide organic cathodes operated for more than 2,100 cycles and reached year-scale-cycling time.We fabricated a 2.18 Ah pouch cell with no significant capacity fading observed after 100 cycles.
基金Supported by National Natural Science Foundation of China(Grant No.51405425)Hebei Provincial Natural Science Foundation of China(Grant No.E2014203255)Independent Research Program Topics of Young Teachers in Yanshan University,China(Grant No.13LGA001)
文摘The two-rotational-degrees-of-freedom（2R） parallel mechanism（PM） with two continuous rotational axes（CRAs） has a simple kinematic model.It is therefore easy to implement trajectory planning,parameter calibration,and motion control,which allows for a variety of application prospects.However,no systematic analysis on structural constraints of the 2R-PM with two CRAs has been performed,and there are only a few types of 2R-PM with two CRAs.Thus,a theory regarding the type synthesis of the 2R-PM with two CRAs is systematically established.First,combining the theories of reciprocal screw and space geometry,the spatial arrangement relationships of the constraint forces applied to the moving platform by the branches are explored,which give the 2R-PM two CRAs.The different distributions of the constraint forces in each branch are also studied.On the basis of the obtained structural constraints of branches,and considering the geometric relationships of constraint forces in each branch,the appropriate kinematic chains are constructed.Through the reasonable configuration of branch kinematic chains corresponding to every structural constraint,a series of new 2R-PMs with two CRAs are finally obtained.
文摘A new kind of quadrilateral assumed stress hy- brid membrane element with drilling degrees of freedom and a traction-free inclined side has been developed based on an extended Hellinger-Reissner principle which is established by expanding the essential terms of the assumed stress field as polynomials in the natural coordinates of the element. The homogeneous equilibrium equations are imposed in a variational sense through the internal displacements which are also expanded in the natural coordinates, while the tractionfree conditions along the inclined side are satisfied exactly. The use of such special element in the finite element solution is shown to be highly accurate when only a very coarse element mesh is used for plates with V-shaped rounded notches or inclined sides.
基金Supported by National Natural Science Foundation of China(Grant Nos.51707082,51877101,51607080)Jiangsu Provincial Natural Science Foundation of China(Grant Nos.BK20170546,BK20150510)+1 种基金China Postdoctoral Science Foundation(Grant No.2017M620192)Priority Academic Program Development of Jiangsu Higher Education Institutions
文摘The current research of supporting and transmission system in flywheel energy storage system(FESS) focuses on the low consumption design. However, friction loss is a non-negligible factor in the high-speed but lightweight FESS energy and momentum storage with mechanical-type supporting system. In order to realize the support system without mechanical loss and to maximize the e ciency of the flywheel battery, a permanent magnet biased magnetic bearings(PMBMB) is applied to the FESS with the advantages of low loss, high critical speed, flexible controllability and compact structure. In this frame, the relevant research of three degrees of freedom(3-DOF) PMBMB for a new type FESS is carried out around the working principle, structural composition, coupling characteristics analysis, mathematical model, and structural design. In order to verify the performance of the 3-DOF PMBMB, the radial force mathematical model and the coupling determination equations of radial two DOF are calculated according to an equivalent magnetic circuit, and radial–axial coupling is analyzed through finite element analysis. Moreover, a control system is presented to solve the control problems in practical applications. The rotor returns to the balanced position in 0.05 s and maintains stable suspension. The displacement fluctuation is approximately 40 μm in the y direction and 30 μm in the x direction. Test results indicate that the dynamic rotor of the proposed flywheel energy storage system with PMBMB has excellent characteristics, such as good start-of-suspension performance and stable suspension characteristics. The proposed research provides the instruction to design and control a low loss support system for FESS.
基金grateful for funding from the National Natural Science Foundation of China(Grant No.52174053,52130401 and 51974344)Natural Science Foundation of Shandong Provincial(ZR2019MEE077).
文摘Asymmetrically modified Janus graphene oxide(JGO)has attracted great attention due to its unique physical chemistry properties and wide applications.The modification degree of Janus nanosheets inevitably affects their interfacial activity,which is essential for their performances in enhanced oil recovery(EOR).In this study,the interfacial properties of Janus graphene oxide(JGO)with various modification degrees at liquid-liquid and liquid-solid interfaces were systematically evaluated via the measurements of interfacial tension(IFT),dilatational modulus,contact angle,and EOR efficiency was further assessed by core flooding tests.It is found that JGO-5 with higher modification degree exhibits the greater ability to reduce IFT(15.16 mN/m)and dilatational modulus(26 mN/m).Furthermore,JGO can construct interfacial and climbing film with the assistance of hydrodynamic power to effectively detach the oil from the rock surface and greatly enhance oil recovery.Moderately modified JGO-2 can highly improve recovery of residual crude oil(11.53%),which is regarded as the promising EOR agent in practical application.The present study firstly focuses on the effects of modification degrees on the JGO interfacial properties and proposes diverse EOR mechanisms for JGO with different modification degrees.
基金co-supported by the National Natural Science Foundation of China (Nos.51105015 and 51075013)Beijing Natural Science Foundation (No.4102035)National Key Technology R&D Program of China (No.2011BAF04B00)
文摘When performing operation tasks, the interaction between a flexible manipulator and a grasped object usually results in an impact. In this paper, a new way is suggested to alleviate impact vibration of a flexible manipulator via its structural characteristic when capturing a moving object. Controllable local degrees of freedom are introduced to the topological structure of the flexible manipulator, and used as an effective tool to combat impact vibration through dynamic coupling. A corresponding method is put forward to reduce impact vibration responses of the flexible manip- ulator via the controllable local degrees of freedom. By planning motion of the controllable local degrees of freedom, appropriate control force can be constructed to increase the modal damping and stiffness and eliminate the exciting force simultaneously, thereby reducing impact vibration responses of the flexible manipulator. Simulations are conducted and results are shown to prove the presented method.
基金supported by the National Natural Science Foundation of China (Grant No. 10902112)
文摘The behavior of vortex-induced vibration of a two-degree-of-freedom cylinder near a deformable wall in steady flow is investigated experimentally. The typical phenomenon of the two-degree-of-freedom cylinder＇s VIV is discussed. The influences of initial gap between the cylinder and the wall on the dynamic responses of the cylinder are analyzed. The comparison is made about dynamic responses of the cylinder with one and two degrees of freedom. Experimental results show that the vibration of the cylinder near a deformable wall with a small value of initial gap-to-diameter ratios can generally be divided into two phases. The initial gap-to-diameter ratios have a noticeable influence on the occurrence of transverse vibration. The transverse maximum amplitude of the cylinder with two degrees of freedom is larger than that of the cylinder with one degree of freedom under the condition with the same values of other parameters. However, the vibration frequency of the cylinder for the two degrees of freedom case is smaller than that for the one degree of freedom case at the same value of Vr number
基金National Natural Science Foundation of China(Grant No.51975007).
文摘A novel compliant mechanism with RPR degrees of freedom(DOF)is proposed where R and P represent rotation and translation DOFs,respectively.The proposed compliant mechanism is obtained from dimension synthesizing a 2-RPU-UPR rigid parallel mechanism with the method of optimization of motion/force transfer characteristic.R,P and U represent rotation,translation and universal pairs,respectively.Firstly,inverse kinematics and Jacobian matrix are analyzed for the dimensional synthesis.Then,output transmission indexes of branches in the parallel mechanism are given.Dimensional synthesis is completed based on the normalized design parameter.And optimization of flexure joints based on constrained energy is carried out.Afterwards,the novel compliant mechanism is obtained by direct replacing method.Mechanical model of the compliant mechanism including static stiffness and input stiffness is built based on the pseudo-rigid body modeling method and virtual work principle.Finally,FEA simulation by Ansys Workbench is carried out to verify DOF,effectiveness of the dimension synthesis,and compliant model.Optimization of motion/force transfer characteristic is first applied for the design of compliant mechanisms to suppress drift of rotation axis in the paper.
