Cyclic metallurgical process for separation and recovery of Cr from vanadium precipitated solution by precipitation with PbCO_(3)and leaching with Na_(2)CO_(3)was investigated.The concentration of Cr residue in the so...Cyclic metallurgical process for separation and recovery of Cr from vanadium precipitated solution by precipitation with PbCO_(3)and leaching with Na_(2)CO_(3)was investigated.The concentration of Cr residue in the solution decreases from 2.360 to 0.001 g/L by adding PbCO_(3)into vanadium precipitated solution according to Pb/Cr molar ratio of 2.5,adjusting the pH to 3.0 and stirring for 180 min at 30℃.Then,the precipitates were leached with hot Na_(2)CO_(3)solution to obtain leaching solution containing Na_(2)CrO_(4)and leaching residue containing PbCO_(3).The leaching efficiency of Cr reaches 96.43%by adding the precipitates into 0.5 mol/L Na_(2)CO_(3)solution with the mass ratio of liquid to solid(L/S)of 10:1 mL/g and stirring for 60 min under pH 9.5 at 70℃.After filtration,leaching residue is reused in Cr precipitation and leaching solution is used to circularly leach the Cr precipitates until Na_(2)CrO_(4)approaches the saturation.Finally,the product of Na_(2)CrO_(4)·4H_(2)O is obtained by evaporation and crystallization of leaching solution.展开更多
The separation and recovery of V from chromium-containing vanadate solution were investigated by a cyclic metallurgical process including selective precipitation of vanadium,vanadium leaching and preparation of vanadi...The separation and recovery of V from chromium-containing vanadate solution were investigated by a cyclic metallurgical process including selective precipitation of vanadium,vanadium leaching and preparation of vanadium pentoxide.By adding Ca(OH)_(2) and ball milling,not only the V in the solution can be selectively precipitated,but also the leaching kinetics of the precipitate is significantly improved.The precipitation efficiency of V is 99.59%by adding Ca(OH)_(2) according to Ca/V molar ratio of 1.75:1 into chromium-containing vanadate solution and ball milling for 60 min at room temperature,while the content of Cr in the precipitate is 0.04%.The leaching rate of V reaches 99.35%by adding NaHCO_(3) into water according to NaHCO_(3)/V molar ratio of 2.74:1 to leach V from the precipitate with L/S ratio of 4:1 mL/g and stirring for 60 min at room temperature.The crystals of NH_(4)VO_(3) are obtained by adjusting the leaching solution pH to be 8.0 with CO2 and then adding NH_(4)HCO_(3) according to NH_(4)HCO_(3)/NaVO_(3) molar ratio of 1:1 and stirring for 8 h at room temperature.After filtration,the crystallized solution containing ammonia is reused to leach the precipitate of calcium vanadates,and the leaching efficiency of V is>99%after stirring for 1 h at room temperature.Finally,the product of V_(2)O_(5) with purity of 99.6%is obtained by calcining the crystals at 560℃ for 2 h.展开更多
The cyclic rotating−bending(CRB)processes under different deformation conditions were carried out to refine the microstructure and improve the mechanical properties of the 65Cu−35Zn brass tubes.The microstructure and ...The cyclic rotating−bending(CRB)processes under different deformation conditions were carried out to refine the microstructure and improve the mechanical properties of the 65Cu−35Zn brass tubes.The microstructure and the mechanical properties in the axial direction of the tubes after the CRB process were studied with the OM,EBSD and conventional tensile test.To obtain the accumulated effective plastic strain of the tube during the CRB process,the FEM simulation was also executed.The results show that the average grain size decreases with the increase of rotation time at RT,and with the decrease of bending angle at 200℃.With the increase of accumulated effective plastic strain during the CRB process,the reduction rate of average grain size of the brass tube increases,the tensile strength of the brass tube increases in wave shape and the elongation increases first and then sharply decreases.展开更多
Al-Cu-Y alloys were prepared by molten salt electrolysis in fluoride-oxide system composed of electrolyte（Na3 AlF6-AlF3-LiF-MgF2） and oxide（Al2 O3-CuO-Y2 O3）. Cathodic reduction process of Al2 O3,CuO and Y2 O3 wer...Al-Cu-Y alloys were prepared by molten salt electrolysis in fluoride-oxide system composed of electrolyte（Na3 AlF6-AlF3-LiF-MgF2） and oxide（Al2 O3-CuO-Y2 O3）. Cathodic reduction process of Al2 O3,CuO and Y2 O3 were analyzed by cyclic voltammetry and chronoamperometry. Components and phase composition of alloy samples prepared by potentiostatic electrolysis were characterized by scanning electron microscopy and energy dispersive spectroscopy. The results show that the Al-Cu-Y alloy can be prepared in the AIF3-NaF-5 wt%LiF-5 wt%MgF2（NaF/AlF3 = 2.2, molecular ratio） eutectic system with mixed oxide（Al2 O3-CuO-Y2 O3） through 2 h at the conditions of a temperature of 1208 K, cell voltage3.0 V, cathode current density 0.7 A/cm^2. Al（Ⅲ） and Cu（Ⅱ） ions can be reduced to zero valence Al（0） and Cu（0） directly on carbonaceous electrode surface by instantaneous nucleation, respectively, the reduction process is controlled by diffusion. The reduction potential of Y（Ⅲ） ions is close to the active ions of fluoride melts, but strengthened phase AI3 Y can be formed through electrochemical reduction and alloyed process with active Al（Ⅲ） and Cu（Ⅱ） ions, meanwhile, the Al2 Cu and Al3 Y phases are distributed at the grain boundary of Al matrix.展开更多
In the past studies, it has been discovered that the shape memory effect(SME) in the Fe-Mn-Si shape memory alloy(Fe-SMA)can gradually be enhanced by a pre-process called as shape memory training process under cyclic t...In the past studies, it has been discovered that the shape memory effect(SME) in the Fe-Mn-Si shape memory alloy(Fe-SMA)can gradually be enhanced by a pre-process called as shape memory training process under cyclic thermo-mechanical loading.On the other hand, it has been shown that the SME of Fe-SMA can also be affected by changing the strain rate. Therefore, it is possible to improve the SME by combining the strain rate sensitivity and shape memory training process. However, the improvement of SME caused by the training process under impact condition is still unclear. For the training process under impact condition, it is difficult to interrupt the test at the desired strain level due to many reflections of stress waves, which reload the specimen from the free ends. In this paper, to obtain reliable experimental results of SME after the training process under impact condition, the stress waves after first loading are eliminated by the double momentum-trap structure introduced into the impact tensile testing apparatus based on the split Hopkinson pressure bar method. In order to achieve an optimum design of the structure used in experiments, the finite element simulation of the structure is performed. Then, tensile tests in the training process of Fe-28Mn-6Si-5Cr alloy at different strain rates including the impact level are conducted and temperature change of the specimen is measured during training and heating process. As a result, the improvement of SME in the alloy after the training process under quasi-static and impact loading is compared with that under quasi-static loading through verification processes.展开更多
基金The authors are grateful for the financial supports from the National Natural Science Foundation of China(No.51974369)NSFC-STINT(No.52111530192)+1 种基金Postgraduate Research Innovation Project of Central South University,China(No.2019zzts244)the Open Sharing Fund for the Large-scale Instruments and Equipments of Central South University,China(No.CSUZC202029).
文摘Cyclic metallurgical process for separation and recovery of Cr from vanadium precipitated solution by precipitation with PbCO_(3)and leaching with Na_(2)CO_(3)was investigated.The concentration of Cr residue in the solution decreases from 2.360 to 0.001 g/L by adding PbCO_(3)into vanadium precipitated solution according to Pb/Cr molar ratio of 2.5,adjusting the pH to 3.0 and stirring for 180 min at 30℃.Then,the precipitates were leached with hot Na_(2)CO_(3)solution to obtain leaching solution containing Na_(2)CrO_(4)and leaching residue containing PbCO_(3).The leaching efficiency of Cr reaches 96.43%by adding the precipitates into 0.5 mol/L Na_(2)CO_(3)solution with the mass ratio of liquid to solid(L/S)of 10:1 mL/g and stirring for 60 min under pH 9.5 at 70℃.After filtration,leaching residue is reused in Cr precipitation and leaching solution is used to circularly leach the Cr precipitates until Na_(2)CrO_(4)approaches the saturation.Finally,the product of Na_(2)CrO_(4)·4H_(2)O is obtained by evaporation and crystallization of leaching solution.
基金The authors are grateful for the financial supports from the National Natural Science Foundation of China(51974369)the Postgraduate Research Innovation Project of Central South University,China(2019zzts244).
文摘The separation and recovery of V from chromium-containing vanadate solution were investigated by a cyclic metallurgical process including selective precipitation of vanadium,vanadium leaching and preparation of vanadium pentoxide.By adding Ca(OH)_(2) and ball milling,not only the V in the solution can be selectively precipitated,but also the leaching kinetics of the precipitate is significantly improved.The precipitation efficiency of V is 99.59%by adding Ca(OH)_(2) according to Ca/V molar ratio of 1.75:1 into chromium-containing vanadate solution and ball milling for 60 min at room temperature,while the content of Cr in the precipitate is 0.04%.The leaching rate of V reaches 99.35%by adding NaHCO_(3) into water according to NaHCO_(3)/V molar ratio of 2.74:1 to leach V from the precipitate with L/S ratio of 4:1 mL/g and stirring for 60 min at room temperature.The crystals of NH_(4)VO_(3) are obtained by adjusting the leaching solution pH to be 8.0 with CO2 and then adding NH_(4)HCO_(3) according to NH_(4)HCO_(3)/NaVO_(3) molar ratio of 1:1 and stirring for 8 h at room temperature.After filtration,the crystallized solution containing ammonia is reused to leach the precipitate of calcium vanadates,and the leaching efficiency of V is>99%after stirring for 1 h at room temperature.Finally,the product of V_(2)O_(5) with purity of 99.6%is obtained by calcining the crystals at 560℃ for 2 h.
基金the National Natural Science Foundation of China(No.51304046)the Grant-in-Aid for Young Scientists(B)of Japan Society for the Promotion of Science of Japan(No.25870594)。
文摘The cyclic rotating−bending(CRB)processes under different deformation conditions were carried out to refine the microstructure and improve the mechanical properties of the 65Cu−35Zn brass tubes.The microstructure and the mechanical properties in the axial direction of the tubes after the CRB process were studied with the OM,EBSD and conventional tensile test.To obtain the accumulated effective plastic strain of the tube during the CRB process,the FEM simulation was also executed.The results show that the average grain size decreases with the increase of rotation time at RT,and with the decrease of bending angle at 200℃.With the increase of accumulated effective plastic strain during the CRB process,the reduction rate of average grain size of the brass tube increases,the tensile strength of the brass tube increases in wave shape and the elongation increases first and then sharply decreases.
基金Project supported by the National Natural Science Foundation of China(51564015)
文摘Al-Cu-Y alloys were prepared by molten salt electrolysis in fluoride-oxide system composed of electrolyte（Na3 AlF6-AlF3-LiF-MgF2） and oxide（Al2 O3-CuO-Y2 O3）. Cathodic reduction process of Al2 O3,CuO and Y2 O3 were analyzed by cyclic voltammetry and chronoamperometry. Components and phase composition of alloy samples prepared by potentiostatic electrolysis were characterized by scanning electron microscopy and energy dispersive spectroscopy. The results show that the Al-Cu-Y alloy can be prepared in the AIF3-NaF-5 wt%LiF-5 wt%MgF2（NaF/AlF3 = 2.2, molecular ratio） eutectic system with mixed oxide（Al2 O3-CuO-Y2 O3） through 2 h at the conditions of a temperature of 1208 K, cell voltage3.0 V, cathode current density 0.7 A/cm^2. Al（Ⅲ） and Cu（Ⅱ） ions can be reduced to zero valence Al（0） and Cu（0） directly on carbonaceous electrode surface by instantaneous nucleation, respectively, the reduction process is controlled by diffusion. The reduction potential of Y（Ⅲ） ions is close to the active ions of fluoride melts, but strengthened phase AI3 Y can be formed through electrochemical reduction and alloyed process with active Al（Ⅲ） and Cu（Ⅱ） ions, meanwhile, the Al2 Cu and Al3 Y phases are distributed at the grain boundary of Al matrix.
基金supported by the Amada Foundation and the 26th ISIJ Research Promotion Grant, Japan。
文摘In the past studies, it has been discovered that the shape memory effect(SME) in the Fe-Mn-Si shape memory alloy(Fe-SMA)can gradually be enhanced by a pre-process called as shape memory training process under cyclic thermo-mechanical loading.On the other hand, it has been shown that the SME of Fe-SMA can also be affected by changing the strain rate. Therefore, it is possible to improve the SME by combining the strain rate sensitivity and shape memory training process. However, the improvement of SME caused by the training process under impact condition is still unclear. For the training process under impact condition, it is difficult to interrupt the test at the desired strain level due to many reflections of stress waves, which reload the specimen from the free ends. In this paper, to obtain reliable experimental results of SME after the training process under impact condition, the stress waves after first loading are eliminated by the double momentum-trap structure introduced into the impact tensile testing apparatus based on the split Hopkinson pressure bar method. In order to achieve an optimum design of the structure used in experiments, the finite element simulation of the structure is performed. Then, tensile tests in the training process of Fe-28Mn-6Si-5Cr alloy at different strain rates including the impact level are conducted and temperature change of the specimen is measured during training and heating process. As a result, the improvement of SME in the alloy after the training process under quasi-static and impact loading is compared with that under quasi-static loading through verification processes.
