This study employed a computational fluid dynamics model with an overset mesh technique to investigate the thrust and power of a floating offshore wind turbine(FOWT)under platform floating motion in the wind–rain fie...This study employed a computational fluid dynamics model with an overset mesh technique to investigate the thrust and power of a floating offshore wind turbine(FOWT)under platform floating motion in the wind–rain field.The impact of rainfall on aerodynamic performance was initially examined using a stationary turbine model in both wind and wind–rain conditions.Subsequently,the study compared the FOWT’s performance under various single degree-of-freedom(DOF)motions,including surge,pitch,heave,and yaw.Finally,the combined effects of wind–rain fields and platform motions involving two DOFs on the FOWT’s aerodynamics were analyzed and compared.The results demonstrate that rain negatively impacts the aerodynamic performance of both the stationary turbines and FOWTs.Pitch-dominated motions,whether involving single or multiple DOFs,caused significant fluctuations in the FOWT aerodynamics.The combination of surge and pitch motions created the most challenging operational environment for the FOWT in all tested scenarios.These findings highlighted the need for stronger construction materials and greater ultimate bearing capacity for FOWTs,as well as the importance of optimizing designs to mitigate excessive pitch and surge.展开更多
In this paper, numerical simulations of FPSO ship motion coupled with LNG tank sloshing with low-filling ratios are conducted. The fully coupled problem is addressed with our own unsteady RANS solver: naoe-FOAM-SJTU d...In this paper, numerical simulations of FPSO ship motion coupled with LNG tank sloshing with low-filling ratios are conducted. The fully coupled problem is addressed with our own unsteady RANS solver: naoe-FOAM-SJTU developed based on the open source tool librar- ies of OpenFOAM. The internal tank sloshing and external wave flow are solved simultaneously. The FPSO model includes 2 LNG tanks. For the ship 3-DOFs are released in the regular beam waves. The filling ratios of the 2 tanks are 20% - 20%, lower than the external free surface. This kind of low-filling condition reduces ship roll motion significantly, and produces complex free surface shapes in tanks. 4 different incident wave frequencies are considered in the simulation in comparison with the existing experimental data. The comparison shows that the numerical re- sults are in good agreement with the experimental data, proving the reliability of the proposed method. The filling conditions with large wave amplitudes are studied further, and due to the coupling effect, violent sloshing occurs in tanks and impulsive pressure forms on bulkhead.展开更多
The production of hydrogen on offshore platform can decrease reliance on the power grid,mitigate transmission losses of electricity,and diminish investment costs for subsea cables.In this study,the hydrodynamic perfor...The production of hydrogen on offshore platform can decrease reliance on the power grid,mitigate transmission losses of electricity,and diminish investment costs for subsea cables.In this study,the hydrodynamic performances of platforms equipped with two types of tanks separately are evaluated and are comprehensively compared with each other.The Volume of Fluid(VOF)two-phase flow model and the Shear−Stress Transport(SST)k−omega turbulence model are applied to simulate the motion responses of the C-type and Moss-type tanks under the same excitation force of platform based on the time-frequency response results of platforms.Comparisons are made among the shape of the liquid hydrogen surface,variations of the wall pressures,changes of the gas-liquid temperatures,and the pressure drop phenomena induced by phase changes inside the tanks.The results indicate that the interaction between wave-induced excitation force and sloshing force from tanks can either increase or decrease the amplitude of platform’s motion.Meanwhile,the thermodynamic responses of liquid hydrogen sloshing inside the tanks correlate positively with the dynamic behavior.Compared with Moss-type tanks,the sloshing of liquid hydrogen in C-type tanks is more intense,accompanied by jetting and breaking wave phenomena.For the C-type tanks,the substantial increase in interfacial area significantly enhances phase change condensation and heat transfer,leading to the rapid decline in temperature and pressure inside the tanks.The results of this study can provide valuable insights for the future design of floating hydrogen storage platform and the selection of tanks on the platform.展开更多
Nonlinear interactions among incident wave, tank-sloshing and floating body coupling motion are investigated. The fully nonlinear sloshing and body-surface nonlinear free surface hydrodynamics is simulated using a Non...Nonlinear interactions among incident wave, tank-sloshing and floating body coupling motion are investigated. The fully nonlinear sloshing and body-surface nonlinear free surface hydrodynamics is simulated using a Non-Uniform Rational B-Spline （NURBS） higher-order panel method in time domain based on the potential theory. A robust and stable improved iterative procedure （Yan and Ma, 2007） for floating bodies is used for calculating the time derivative of velocity potential and floating body motion. An energy dissipation condition based on linear theory adopted by Huang （2011） is developed to consider flow viscosity effects of sloshing flow in nonlinear model. A two-dimensional tank model test was performed to identify its validity. The present nonlinear coupling sway motion results are subsequently compared with the corresponding Rognebakke and Faltinsen （2003）＇s experimental results, showing fair agreement. Thus, the numerical approach presented in this paper is expected to be very efficient and realistic in evaluating the coupling effects of nonlinear sloshing and body motion.展开更多
The human thumb plays a crucial role in performing coordinated hand movements for precise tool use.However,quantifying and interpreting the kinematics and couplings of the six degrees of freedom(6DOF)between the inter...The human thumb plays a crucial role in performing coordinated hand movements for precise tool use.However,quantifying and interpreting the kinematics and couplings of the six degrees of freedom(6DOF)between the interphalangeal(IP)and metacarpophalangeal(MCP)joints during hand functional tasks remains challenging.To address this issue,advanced dynamic biplane radiography combined with a model-based 2D–3D tracking technique was employed to decode the inherent kinematics of the thumb IP and MCP joints during key pinch,tip pinch,palmar pinch and wide grasp.The results indicate that the functional tasks of the thumb are intricately modulated by the 3D rotational and translational motions of the IP and MCP joints.The IP joint exhibited the greatest flexion/extension range of motion during the tip pinch task(67.2°±8.4°),compared to smaller ranges in key pinch(27.6°±3.8°)and wide grasp(16.2°±7.1°)tasks.In the wide grasp task,the IP joint showed more movement in the radius/ulna direction(3.4±1.2 mm)compared to tip pinch(3.1±0.8 mm).Furthermore,the kinematic data of the IP joint challenge the traditional notion that the IP joint normally acts as a hinge mechanism.The results of this study help to elucidate the kinematics of human thumb IP and MCP joints and may provide new inspiration for the design of high-performance bionic hands or thumb prosthetics as well as for evaluating the outcomes of thumb therapeutic interventions and surgical procedures.展开更多
The dynamic analysis of a Tension Leg Platform (TLP) in random wave is investigated by considering the set-down of a floating body. The nonlinear restoring stiffness is derived with the set-down motion of a floating b...The dynamic analysis of a Tension Leg Platform (TLP) in random wave is investigated by considering the set-down of a floating body. The nonlinear restoring stiffness is derived with the set-down motion of a floating body and the coupled motion of the tension leg and platform and the differential equations of the motion are established. The study focuses on the influence of the set-down motion on the nonlinear response of the platform. By considering different significant wave heights and currents, motion responses of the platform are calculated and compared. The analysis shows that the set-down motion significantly increases the heave motion with low frequency and the equilibrium position of the heave motion with the set-down motion is much lower than that without set-down motion. The results in this paper indicate that the set-down motion has a major impact on the safety of the platform inproduction operation, and it is also a threat to the strength of tension legs and risers.展开更多
Simulating the coupled motions of multiple bodies in the time domain is a complex problem because of the strong hydrodynamic interactions and coupled effect of various mechanical connectors. In this study, we investig...Simulating the coupled motions of multiple bodies in the time domain is a complex problem because of the strong hydrodynamic interactions and coupled effect of various mechanical connectors. In this study, we investigate the hydrodynamic responses of three barges moored side-by-side in a floatover operation in the frequency and time domains. In the frequency domain, the damping lid method is adopted to improve the overestimated hydrodynamic coefficients calculated from conventional potential flow theory. A time-domain computing program based on potential flow theory and impulse theory is compiled for analyses that consider multibody hydrodynamic interactions and mechanical effects from lines and fenders. Correspondingly, an experiment is carried out for comparison with the numerical results. All statistics, time series, and power density spectra from decay and irregular wave tests are in a fairly good agreement.展开更多
In order to clarify the mechanism and main influencing factors of the vibration energy coupling transmission with a dual-piston structure,a thermodynamic and dynamic coupling model of the free piston linear generator(...In order to clarify the mechanism and main influencing factors of the vibration energy coupling transmission with a dual-piston structure,a thermodynamic and dynamic coupling model of the free piston linear generator(FPLG)was established.The system energy conversion,vibration energy coupling transmission,and influencing factors were studied in detail.The coupling transmission paths and the secondary influence mechanism from in-cylinder combustion on vibration energy transmission were obtained.In addition,the influence of the movement characteristics of the dual-piston on the vibration energy transmission was studied,and the typical parameter variation law was obtained,which provides theoretical guidance for the subsequent vibration reduction design of the FPLG.展开更多
The launching and recovery process of a human-occupied vehicle(HOV)faces more complex wave effects than other types of submersible operations.However,due to the nonlinearity between the HOV and its mother ship,difficu...The launching and recovery process of a human-occupied vehicle(HOV)faces more complex wave effects than other types of submersible operations.However,due to the nonlinearity between the HOV and its mother ship,difficulties occur in theoretically simulating their coupled motion and hydrodynamics.The coupled motion responses and the load under different regular wave conditions are investigated experimentally in this study.The optimized design of the experimental scheme simulated the launching and recovery process of the mother ship and HOV in regular waves.The attitude sensor performed synchronous real-time measurement of the coupled motion between the mother ship and HOV as well as obtained the load data on the coupled motion under different cable lengths.The results show that models in heading waves mainly lead to the vertical motion of the hoisting point.In beam waves,the transverse and vertical motions of the hoisting point occur in a certain frequency of waves.Under the heading and beam wave conditions,the longer the hoisting cable is,the greater the movement amplitude of the submersible is.Moreover,compared with the condition of the beam waves,the hoisting submersible has less influence on the mother ship under the condition of the heading waves.The findings provide theoretical support for the design optimization of the launching and recovery operation.展开更多
Motion responses of two ships advancing parallel in waves with hydrodynamic interactions are investigated in this paper. Within the framework of the frequency-domain potential flow theory, a semi-analytical higher-ord...Motion responses of two ships advancing parallel in waves with hydrodynamic interactions are investigated in this paper. Within the framework of the frequency-domain potential flow theory, a semi-analytical higher-order translating-pulsating source(HOTP) method is presented to solve the problems of coupled radiation and diffraction potential. The method employs nine-node bi-quadratic curvilinear elements to discretize the boundary integral equations(BIEs) constructed over the mean wetted surface of the two ship hulls. In order to eliminate the numerical oscillation, analytical quadrature formulas are derived and adopted to evaluate the integrals related to the Froudedependent part of the Green’s function along the horizontal direction in the BIEs. Based on the method, a numerical program is originally coded. Through the calculations of hydrodynamic responses of single ships, the numerical implementation is proved successful. Then the validated program is applied in the investigations on the hydrodynamic interactions of two identical Wigley Ⅲ hulls and the underway replenishment of a frigate and a supply ship in waves with and without stagger, respectively. The comparison between the present computed results with experimental data and numerical solutions of other methods shows that the semi-analytical HOTP method is of higher accuracy than the pulsating source Green’s function method with speed correction and better stability than the traditional HOTP method based on Gauss quadrature. In addition, for two ships with obviously different dimensions,the influence of hydrodynamic interactions on the smaller ship is found to be more noticeable than that on the larger ship, which leads to the differences between the motions of frigate with and without the presence of supply ship.展开更多
A problem of couple motion between vessel wall and blood in the entrance regionof a tapered vessel is considered in this paper A mathematical model of co-coupleaction is formed for both motion of vessel wall and blood...A problem of couple motion between vessel wall and blood in the entrance regionof a tapered vessel is considered in this paper A mathematical model of co-coupleaction is formed for both motion of vessel wall and blood flow in the entrance regance regionof elastic vessel with tapered angle. Under the situation that the relative boundary conditions are satisfied a.set of velocity distribution formula. pressure distributionformula for the blood flow in a tapered elastic vessel are derived. Some importantconclusions are obtained.展开更多
For general dynamic positioning systems,controllers are mainly based on the feedback of motions only in the horizontal plane.However,for marine structures with a small water plane area and low metacentric height,undes...For general dynamic positioning systems,controllers are mainly based on the feedback of motions only in the horizontal plane.However,for marine structures with a small water plane area and low metacentric height,undesirable surge and pitch oscillations may be induced by the thruster actions.In this paper,three control laws are investigated to suppress the induced pitch motion by adding pitch rate,pitch angle or pitch acceleration into the feedback control loop.Extensive numerical simulations are conducted with a semi-submersible platform for each control law.The influences of additional terms on surge−pitch coupled motions are analyzed in both frequency and time domain.The mechanical constraints of the thrust allocation and the frequency characters of external forces are simultaneously considered.It is concluded that adding pitch angle or pitch acceleration into the feedback loop changes the natural frequency in pitch,and its performance is highly dependent on the frequency distribution of external forces,while adding pitch rate into the feedback loop is always effective in mitigating surge−pitch coupled motions.展开更多
A layered modeling method is proposed to resolve the problems resulting from the complexity of the error model of a multi-axis motion control system. In this model, a low level layer can be used as a virtual axis by t...A layered modeling method is proposed to resolve the problems resulting from the complexity of the error model of a multi-axis motion control system. In this model, a low level layer can be used as a virtual axis by the high level layer. The first advantage of this model is that the complex error model of a four-axis motion control system can be divided into several simple layers and each layer has different coupling strength to match the real control system. The second advantage lies in the fact that the controller in each layer can be designed specifically for a certain purpose. In this research, a three-layered cross coupling scheme in a four-axis motion control system is proposed to compensate the contouring error of the motion control system. Simulation results show that the maximum contouring error is reduced from 0.208 mm to 0.022 mm and the integration of absolute error is reduced from 0.108 mm to 0.015 mm, which are respectively better than 0.027 mm and 0.037 mm by the traditional method. And in the bottom layer the proposed method also has remarkable ability to achieve high contouring accuracy.展开更多
Coilable masts are extensively utilized in aerospace systems owing to their structural simplicity,reliability,and high deployment ratios.However,their application is constrained by compression-twist coupling motion du...Coilable masts are extensively utilized in aerospace systems owing to their structural simplicity,reliability,and high deployment ratios.However,their application is constrained by compression-twist coupling motion during deployment,which induces large structure deformations and displacements.To address this limitation,this study proposes a parallel chiral coilable mast with synergistic control strategies.This design transforms the conventional unidirectional compression-twist motion into a bidirectional synchronous pure sliding deployment.Three pretensioned modes were developed for a single-bay unit based on diagonal constraints,leveraging the critical role of diagonals in achieving structural bistability.A topologyoptimized multi-bay configuration enables directional rotation while maintaining structural stability via pretension modes.By redesigning structural constraints on the top and bottom disks,a decoupling strategy achieves pure linear motion at the top batten frame,significantly expanding the operational envelope.The parallel-designed chiral configuration is developed based on the synergistic control strategies of these two structural constraints.Numerical simulations and experimental validation confirm the effectiveness and feasibility of the synergistic control strategies.The chiral configuration facilitates multifunctional deployment capabilities in geometrically unconstrained environments,demonstrating substantial improvements over conventional designs.展开更多
Point absorber wave energy device with multiple degrees of freedom(DOF) is assumed to have a better absorption ability of mechanical energy from ocean waves. In this paper, a coaxial symmetric articulated point absorb...Point absorber wave energy device with multiple degrees of freedom(DOF) is assumed to have a better absorption ability of mechanical energy from ocean waves. In this paper, a coaxial symmetric articulated point absorber wave energy converter with two degrees of freedom is presented. The mechanical equations of the oscillation buoy with power take-off mechanism(PTO) in regular waves are established. The three-dimensional numerical wave tank is built in consideration of the buoy motion based upon the CFD method. The appropriate simulation elements are selected for the buoy and wave parameters. The feasibility of the CFD method is verified through the contrast between the numerical simulation results of typical wave conditions and test results. In such case, the buoy with single DOF of heave, pitch and their coupling motion considering free(no PTO damping) and damped oscillations in regular waves are simulated by using the verified CFD method respectively. The hydrodynamic and wave energy conversion characteristics with typical wave conditions are analyzed. The numerical results show that the heave and pitch can affect each other in the buoy coupling motion, hydrodynamic loads, wave energy absorption and flow field.The total capture width ratio with two coupled DOF motion is higher than that with a single DOF motion. The wave energy conversion of a certain DOF motion may be higher than that of the single certain DOF motion even though the wave is at the resonance period. When the wave periods are high enough, the interaction between the coupled DOF motions can be neglected.展开更多
The pre-research on mobility analysis presented a unified-mobility formula and a methodology based on reciprocal screw theory by HUANG, which focused on classical and modem parallel mechanisms. However its range of ap...The pre-research on mobility analysis presented a unified-mobility formula and a methodology based on reciprocal screw theory by HUANG, which focused on classical and modem parallel mechanisms. However its range of application needs to further extend to general multi-loop spatial mechanism. This kind of mechanism is not only more complex in structure but also with strong motion coupling among loops, making the mobility analysis even more complicated, and the relevant research has long been ignored. It is focused on how to apply the new principle for general spatial mechanism to those various multi-loop spatial mechanisms, and some new meaningful knowledge is further found. Several typical examples of the genera/multi-loop spatial mechanisms with motion couple even strong motion couple are considered. These spatial mechanisms include different closing way： over-constraint appearing in rigid closure, in movable closure, and in dynamic closure as well; these examples also include two different new methods to solve this kind of issue： the way to recognize over-constraints by analyzing relative movement between two connected links and by constructing a virtual loop to recognize over-constraints. In addition, over-constraint determination tabulation is brought to analyze the motion couple. The researches above are all based upon the screw theory. All these multi-loop spatial mechanisms with different kinds of structures can completely be solved by following the directions and examples, and the new mobility theory based on the screw theory is also proved to be valid. This study not only enriches and develops the theory and makes the theory more universal, but also has a special meaning for innovation in mechanical engineering.展开更多
This paper presents a design of boundary controllers implemented at the top end for global stabilization of a marine riser in a three dimensional space under environmental loadings. Based on the energy approach, nonli...This paper presents a design of boundary controllers implemented at the top end for global stabilization of a marine riser in a three dimensional space under environmental loadings. Based on the energy approach, nonlinear partial differential equations of motion, including bending-bending and longitudinal-bending couplings for the risers are derived. The couplings cause mutual effects between the three independent directions in the riser＇s motions, and make it difficult to minimize its vibrations. The Lyapunov direct method is employed to design the boundary controller. It is shown that the proposed boundary controllers can effectively reduce the riser＇s vibration. Stability analysis of the closed-loop system is performed using the Lyapunov direct method. Numerical simulations illustrate the results.展开更多
A rigid flexible coupling physical model which can represent a flexible spacecraft is investigated in this paper. By applying the mechanics theory in a non-inertial coordinate system,the rigid flexible coupling dynami...A rigid flexible coupling physical model which can represent a flexible spacecraft is investigated in this paper. By applying the mechanics theory in a non-inertial coordinate system,the rigid flexible coupling dynamic model with dynamic stiffening is established via the subsystemmodeling framework. It is clearly elucidated for the first time that,dynamic stiffening is produced by the coupling effect of the centrifugal inertial load distributed on the beamand the transverse vibration deformation of the beam. The modeling approach in this paper successfully avoids problems which are caused by other popular modeling methods nowadays： the derivation process is too complex by using only one dynamic principle; a clearly theoretical explanation for dynamic stiffening can＇t be provided. First,the continuous dynamic models of the flexible beamand the central rigid body are established via structural dynamics and angular momentumtheory respectively. Then,based on the conclusions of orthogonalization about the normal constrained modes,the finite dimensional dynamic model suitable for controller design is obtained. The numerical simulation validations showthat： dynamic stiffening is successfully incorporated into the dynamic characteristics of the first-order model established in this paper,which can indicate the dynamic responses of the rigid flexible coupling system with large overall motion accurately,and has a clear modeling mechanism,concise expressions and a good convergence.展开更多
Accurate knowledge of the kinematics of the in vivo Ankle Joint Complex(AJC)is critical for understanding the biomechanical function of the foot and assessing postoperative rehabilitation of ankle disorders,as well as...Accurate knowledge of the kinematics of the in vivo Ankle Joint Complex(AJC)is critical for understanding the biomechanical function of the foot and assessing postoperative rehabilitation of ankle disorders,as well as an essential guide to the design of ankle–foot assistant devices.However,detailed analysis of the continuous 3D motion of the tibiotalar and subtalar joints during normal walking throughout the stance phase is still considered to be lacking.In this study,dynamic radiographs of the hindfoot were acquired from eight subjects during normal walking.Natural motions with six Degrees of Freedom(DOF)and the coupled patterns of the two joints were analyzed.It was found that the movements of the two joints were mostly in opposite directions(including rotation and translation),mainly in the early and late stages.There were significant differences in the Range of Motion(ROM)in Dorsiflexion/Plantarflexion(D/P),Inversion/Eversion(In/Ev),and Anterior–Posterior(AP)and Medial–Lateral(ML)translation of the tibiotalar and subtalar joints(p<0.05).Plantarflexion of the tibiotalar joint was coupled with eversion and posterior translation of the subtalar joint during the impact phase(R^(2)=0.87 and 0.86,respectively),and plantarflexion of the tibiotalar joint was coupled with inversion and anterior translation of the subtalar joint during the push-off phase(R^(2)=0.93 and 0.75,respectively).This coordinated coupled motion of the two joints may be a manifestation of the AJC to move flexibly while bearing weight and still have stability.展开更多
Developing a dual-cross-linked network,with weaker cross-links to dissipate energy and stronger ones to sustain integrity,is an effective protocol to overcome the well-known trade-off between hardness and stretchabili...Developing a dual-cross-linked network,with weaker cross-links to dissipate energy and stronger ones to sustain integrity,is an effective protocol to overcome the well-known trade-off between hardness and stretchability for achieving high toughness.Although this protocol has been extensively explored in the past two decades,the molecular mechanism underlying the protocol is yet to be better understood.In this study,we copolymerize hexyl methacrylate with hydrogen-bonding n-isopropyl methacrylamide and vitrimeric cross-linkers to prepare dual-cross-linked networks.During the tensile tests,the energy dissipation is greatly enhanced by increasing the density of hydrogen bonds,enabling the initial modulus to increase from∼1 MPa,which is typical for an elastomer,to 300 MPa,which is closer to the glass.Nevertheless,the breakup of the hydrogen bonds during the elongation significantly dissipates the energy,leading to the softening of the materials,thereby facilitating the stretch to high strain.The softening process,seen as an overshoot in the stress−strain curve,is well captured by the Dobrynin theory modified by Konkolewicz and co-workers upon including a strain rate-dependent element.The deviation at a high content of hydrogen bonds,where the distance between hydrogen bonds becomes smaller than the Kuhn length,is attributed to the coupled motion of the hydrogen bonds.展开更多
基金Supported by the National Natural Science Foundation of China(51679080 and 51379073)the Fundamental Research Funds for the Central Universities(B230205020).
文摘This study employed a computational fluid dynamics model with an overset mesh technique to investigate the thrust and power of a floating offshore wind turbine(FOWT)under platform floating motion in the wind–rain field.The impact of rainfall on aerodynamic performance was initially examined using a stationary turbine model in both wind and wind–rain conditions.Subsequently,the study compared the FOWT’s performance under various single degree-of-freedom(DOF)motions,including surge,pitch,heave,and yaw.Finally,the combined effects of wind–rain fields and platform motions involving two DOFs on the FOWT’s aerodynamics were analyzed and compared.The results demonstrate that rain negatively impacts the aerodynamic performance of both the stationary turbines and FOWTs.Pitch-dominated motions,whether involving single or multiple DOFs,caused significant fluctuations in the FOWT aerodynamics.The combination of surge and pitch motions created the most challenging operational environment for the FOWT in all tested scenarios.These findings highlighted the need for stronger construction materials and greater ultimate bearing capacity for FOWTs,as well as the importance of optimizing designs to mitigate excessive pitch and surge.
文摘In this paper, numerical simulations of FPSO ship motion coupled with LNG tank sloshing with low-filling ratios are conducted. The fully coupled problem is addressed with our own unsteady RANS solver: naoe-FOAM-SJTU developed based on the open source tool librar- ies of OpenFOAM. The internal tank sloshing and external wave flow are solved simultaneously. The FPSO model includes 2 LNG tanks. For the ship 3-DOFs are released in the regular beam waves. The filling ratios of the 2 tanks are 20% - 20%, lower than the external free surface. This kind of low-filling condition reduces ship roll motion significantly, and produces complex free surface shapes in tanks. 4 different incident wave frequencies are considered in the simulation in comparison with the existing experimental data. The comparison shows that the numerical re- sults are in good agreement with the experimental data, proving the reliability of the proposed method. The filling conditions with large wave amplitudes are studied further, and due to the coupling effect, violent sloshing occurs in tanks and impulsive pressure forms on bulkhead.
基金supported by the National Natural Science Foundation of China(Grant No.51979130).
文摘The production of hydrogen on offshore platform can decrease reliance on the power grid,mitigate transmission losses of electricity,and diminish investment costs for subsea cables.In this study,the hydrodynamic performances of platforms equipped with two types of tanks separately are evaluated and are comprehensively compared with each other.The Volume of Fluid(VOF)two-phase flow model and the Shear−Stress Transport(SST)k−omega turbulence model are applied to simulate the motion responses of the C-type and Moss-type tanks under the same excitation force of platform based on the time-frequency response results of platforms.Comparisons are made among the shape of the liquid hydrogen surface,variations of the wall pressures,changes of the gas-liquid temperatures,and the pressure drop phenomena induced by phase changes inside the tanks.The results indicate that the interaction between wave-induced excitation force and sloshing force from tanks can either increase or decrease the amplitude of platform’s motion.Meanwhile,the thermodynamic responses of liquid hydrogen sloshing inside the tanks correlate positively with the dynamic behavior.Compared with Moss-type tanks,the sloshing of liquid hydrogen in C-type tanks is more intense,accompanied by jetting and breaking wave phenomena.For the C-type tanks,the substantial increase in interfacial area significantly enhances phase change condensation and heat transfer,leading to the rapid decline in temperature and pressure inside the tanks.The results of this study can provide valuable insights for the future design of floating hydrogen storage platform and the selection of tanks on the platform.
基金Foundation item： Supported by the National Natural Science Foundation of China （Grant No. 51079032） and the ＂111 project＂ （Grant No. B07019）.
文摘Nonlinear interactions among incident wave, tank-sloshing and floating body coupling motion are investigated. The fully nonlinear sloshing and body-surface nonlinear free surface hydrodynamics is simulated using a Non-Uniform Rational B-Spline （NURBS） higher-order panel method in time domain based on the potential theory. A robust and stable improved iterative procedure （Yan and Ma, 2007） for floating bodies is used for calculating the time derivative of velocity potential and floating body motion. An energy dissipation condition based on linear theory adopted by Huang （2011） is developed to consider flow viscosity effects of sloshing flow in nonlinear model. A two-dimensional tank model test was performed to identify its validity. The present nonlinear coupling sway motion results are subsequently compared with the corresponding Rognebakke and Faltinsen （2003）＇s experimental results, showing fair agreement. Thus, the numerical approach presented in this paper is expected to be very efficient and realistic in evaluating the coupling effects of nonlinear sloshing and body motion.
基金supported by the National Natural Science Foundation of China(No.52175270)the Project of Scientific and Technological Development Plan of Jilin Province(No.20220508130RC).
文摘The human thumb plays a crucial role in performing coordinated hand movements for precise tool use.However,quantifying and interpreting the kinematics and couplings of the six degrees of freedom(6DOF)between the interphalangeal(IP)and metacarpophalangeal(MCP)joints during hand functional tasks remains challenging.To address this issue,advanced dynamic biplane radiography combined with a model-based 2D–3D tracking technique was employed to decode the inherent kinematics of the thumb IP and MCP joints during key pinch,tip pinch,palmar pinch and wide grasp.The results indicate that the functional tasks of the thumb are intricately modulated by the 3D rotational and translational motions of the IP and MCP joints.The IP joint exhibited the greatest flexion/extension range of motion during the tip pinch task(67.2°±8.4°),compared to smaller ranges in key pinch(27.6°±3.8°)and wide grasp(16.2°±7.1°)tasks.In the wide grasp task,the IP joint showed more movement in the radius/ulna direction(3.4±1.2 mm)compared to tip pinch(3.1±0.8 mm).Furthermore,the kinematic data of the IP joint challenge the traditional notion that the IP joint normally acts as a hinge mechanism.The results of this study help to elucidate the kinematics of human thumb IP and MCP joints and may provide new inspiration for the design of high-performance bionic hands or thumb prosthetics as well as for evaluating the outcomes of thumb therapeutic interventions and surgical procedures.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51239008 and 51279130)
文摘The dynamic analysis of a Tension Leg Platform (TLP) in random wave is investigated by considering the set-down of a floating body. The nonlinear restoring stiffness is derived with the set-down motion of a floating body and the coupled motion of the tension leg and platform and the differential equations of the motion are established. The study focuses on the influence of the set-down motion on the nonlinear response of the platform. By considering different significant wave heights and currents, motion responses of the platform are calculated and compared. The analysis shows that the set-down motion significantly increases the heave motion with low frequency and the equilibrium position of the heave motion with the set-down motion is much lower than that without set-down motion. The results in this paper indicate that the set-down motion has a major impact on the safety of the platform inproduction operation, and it is also a threat to the strength of tension legs and risers.
基金financially supported by Lloyd’s Register Foundation(LRF),a UK-registered charity and sole shareholder of Lloyd’s Register Group Ltd.the Youth Innovation Fund of State Key Laboratory of Ocean Engineering(Grant No.GKZD010059-21)
文摘Simulating the coupled motions of multiple bodies in the time domain is a complex problem because of the strong hydrodynamic interactions and coupled effect of various mechanical connectors. In this study, we investigate the hydrodynamic responses of three barges moored side-by-side in a floatover operation in the frequency and time domains. In the frequency domain, the damping lid method is adopted to improve the overestimated hydrodynamic coefficients calculated from conventional potential flow theory. A time-domain computing program based on potential flow theory and impulse theory is compiled for analyses that consider multibody hydrodynamic interactions and mechanical effects from lines and fenders. Correspondingly, an experiment is carried out for comparison with the numerical results. All statistics, time series, and power density spectra from decay and irregular wave tests are in a fairly good agreement.
文摘In order to clarify the mechanism and main influencing factors of the vibration energy coupling transmission with a dual-piston structure,a thermodynamic and dynamic coupling model of the free piston linear generator(FPLG)was established.The system energy conversion,vibration energy coupling transmission,and influencing factors were studied in detail.The coupling transmission paths and the secondary influence mechanism from in-cylinder combustion on vibration energy transmission were obtained.In addition,the influence of the movement characteristics of the dual-piston on the vibration energy transmission was studied,and the typical parameter variation law was obtained,which provides theoretical guidance for the subsequent vibration reduction design of the FPLG.
基金National Natural Science Foundation of China(Grant No.51909039)Shandong Provincial Key Laboratory of Ocean Engineering(Grant No.201807).
文摘The launching and recovery process of a human-occupied vehicle(HOV)faces more complex wave effects than other types of submersible operations.However,due to the nonlinearity between the HOV and its mother ship,difficulties occur in theoretically simulating their coupled motion and hydrodynamics.The coupled motion responses and the load under different regular wave conditions are investigated experimentally in this study.The optimized design of the experimental scheme simulated the launching and recovery process of the mother ship and HOV in regular waves.The attitude sensor performed synchronous real-time measurement of the coupled motion between the mother ship and HOV as well as obtained the load data on the coupled motion under different cable lengths.The results show that models in heading waves mainly lead to the vertical motion of the hoisting point.In beam waves,the transverse and vertical motions of the hoisting point occur in a certain frequency of waves.Under the heading and beam wave conditions,the longer the hoisting cable is,the greater the movement amplitude of the submersible is.Moreover,compared with the condition of the beam waves,the hoisting submersible has less influence on the mother ship under the condition of the heading waves.The findings provide theoretical support for the design optimization of the launching and recovery operation.
基金This work was financially supported by the National Natural Science Foundation of China(Grant No.52101357)the Natural Science Foundation of the Jiangsu Higher Education Institutions of China(Grant No.21KJB580012)the Scientific Research Start-up Fund of Jiangsu University of Science and Technology.
文摘Motion responses of two ships advancing parallel in waves with hydrodynamic interactions are investigated in this paper. Within the framework of the frequency-domain potential flow theory, a semi-analytical higher-order translating-pulsating source(HOTP) method is presented to solve the problems of coupled radiation and diffraction potential. The method employs nine-node bi-quadratic curvilinear elements to discretize the boundary integral equations(BIEs) constructed over the mean wetted surface of the two ship hulls. In order to eliminate the numerical oscillation, analytical quadrature formulas are derived and adopted to evaluate the integrals related to the Froudedependent part of the Green’s function along the horizontal direction in the BIEs. Based on the method, a numerical program is originally coded. Through the calculations of hydrodynamic responses of single ships, the numerical implementation is proved successful. Then the validated program is applied in the investigations on the hydrodynamic interactions of two identical Wigley Ⅲ hulls and the underway replenishment of a frigate and a supply ship in waves with and without stagger, respectively. The comparison between the present computed results with experimental data and numerical solutions of other methods shows that the semi-analytical HOTP method is of higher accuracy than the pulsating source Green’s function method with speed correction and better stability than the traditional HOTP method based on Gauss quadrature. In addition, for two ships with obviously different dimensions,the influence of hydrodynamic interactions on the smaller ship is found to be more noticeable than that on the larger ship, which leads to the differences between the motions of frigate with and without the presence of supply ship.
文摘A problem of couple motion between vessel wall and blood in the entrance regionof a tapered vessel is considered in this paper A mathematical model of co-coupleaction is formed for both motion of vessel wall and blood flow in the entrance regance regionof elastic vessel with tapered angle. Under the situation that the relative boundary conditions are satisfied a.set of velocity distribution formula. pressure distributionformula for the blood flow in a tapered elastic vessel are derived. Some importantconclusions are obtained.
基金the National Natural Science Foundation of China(Grant Nos.51179103 and 51979167)the Ministry of Industry and Information Technology(Grant No.[2016]22)the Hainan Provincial Joint Project of Sanya Bay Science and Technology City(Grant No.520LH051).
文摘For general dynamic positioning systems,controllers are mainly based on the feedback of motions only in the horizontal plane.However,for marine structures with a small water plane area and low metacentric height,undesirable surge and pitch oscillations may be induced by the thruster actions.In this paper,three control laws are investigated to suppress the induced pitch motion by adding pitch rate,pitch angle or pitch acceleration into the feedback control loop.Extensive numerical simulations are conducted with a semi-submersible platform for each control law.The influences of additional terms on surge−pitch coupled motions are analyzed in both frequency and time domain.The mechanical constraints of the thrust allocation and the frequency characters of external forces are simultaneously considered.It is concluded that adding pitch angle or pitch acceleration into the feedback loop changes the natural frequency in pitch,and its performance is highly dependent on the frequency distribution of external forces,while adding pitch rate into the feedback loop is always effective in mitigating surge−pitch coupled motions.
基金Project(51005086)supported by the National Natural Science Foundation of ChinaProject(2010MS085)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(DMETKF2013008)supported by the Open Project of the State Key Laboratory of Digital Manufacturing Equipment and Technology,China
文摘A layered modeling method is proposed to resolve the problems resulting from the complexity of the error model of a multi-axis motion control system. In this model, a low level layer can be used as a virtual axis by the high level layer. The first advantage of this model is that the complex error model of a four-axis motion control system can be divided into several simple layers and each layer has different coupling strength to match the real control system. The second advantage lies in the fact that the controller in each layer can be designed specifically for a certain purpose. In this research, a three-layered cross coupling scheme in a four-axis motion control system is proposed to compensate the contouring error of the motion control system. Simulation results show that the maximum contouring error is reduced from 0.208 mm to 0.022 mm and the integration of absolute error is reduced from 0.108 mm to 0.015 mm, which are respectively better than 0.027 mm and 0.037 mm by the traditional method. And in the bottom layer the proposed method also has remarkable ability to achieve high contouring accuracy.
基金supported by the National Key R&D Program of China(Grant No.2018YFB1304600)the CAS Interdisciplinary Innovation Team(Grant No.JCTD-2018-11)the National Natural Science Foundation of China(Grant No.51775541)。
文摘Coilable masts are extensively utilized in aerospace systems owing to their structural simplicity,reliability,and high deployment ratios.However,their application is constrained by compression-twist coupling motion during deployment,which induces large structure deformations and displacements.To address this limitation,this study proposes a parallel chiral coilable mast with synergistic control strategies.This design transforms the conventional unidirectional compression-twist motion into a bidirectional synchronous pure sliding deployment.Three pretensioned modes were developed for a single-bay unit based on diagonal constraints,leveraging the critical role of diagonals in achieving structural bistability.A topologyoptimized multi-bay configuration enables directional rotation while maintaining structural stability via pretension modes.By redesigning structural constraints on the top and bottom disks,a decoupling strategy achieves pure linear motion at the top batten frame,significantly expanding the operational envelope.The parallel-designed chiral configuration is developed based on the synergistic control strategies of these two structural constraints.Numerical simulations and experimental validation confirm the effectiveness and feasibility of the synergistic control strategies.The chiral configuration facilitates multifunctional deployment capabilities in geometrically unconstrained environments,demonstrating substantial improvements over conventional designs.
基金financially supported by the National Natural Science Foundation of China(Grant No.51579055)the Natural Science Foundation of Jiangsu Province(Grant No.BK20180980)
文摘Point absorber wave energy device with multiple degrees of freedom(DOF) is assumed to have a better absorption ability of mechanical energy from ocean waves. In this paper, a coaxial symmetric articulated point absorber wave energy converter with two degrees of freedom is presented. The mechanical equations of the oscillation buoy with power take-off mechanism(PTO) in regular waves are established. The three-dimensional numerical wave tank is built in consideration of the buoy motion based upon the CFD method. The appropriate simulation elements are selected for the buoy and wave parameters. The feasibility of the CFD method is verified through the contrast between the numerical simulation results of typical wave conditions and test results. In such case, the buoy with single DOF of heave, pitch and their coupling motion considering free(no PTO damping) and damped oscillations in regular waves are simulated by using the verified CFD method respectively. The hydrodynamic and wave energy conversion characteristics with typical wave conditions are analyzed. The numerical results show that the heave and pitch can affect each other in the buoy coupling motion, hydrodynamic loads, wave energy absorption and flow field.The total capture width ratio with two coupled DOF motion is higher than that with a single DOF motion. The wave energy conversion of a certain DOF motion may be higher than that of the single certain DOF motion even though the wave is at the resonance period. When the wave periods are high enough, the interaction between the coupled DOF motions can be neglected.
基金Supported by National Natural Science Foundation of China(Grant No.51005195)Natural Science Research Fund for Youth in Higher Education Institutions of Hebei Province,China(Grant No.QN2014175)
文摘The pre-research on mobility analysis presented a unified-mobility formula and a methodology based on reciprocal screw theory by HUANG, which focused on classical and modem parallel mechanisms. However its range of application needs to further extend to general multi-loop spatial mechanism. This kind of mechanism is not only more complex in structure but also with strong motion coupling among loops, making the mobility analysis even more complicated, and the relevant research has long been ignored. It is focused on how to apply the new principle for general spatial mechanism to those various multi-loop spatial mechanisms, and some new meaningful knowledge is further found. Several typical examples of the genera/multi-loop spatial mechanisms with motion couple even strong motion couple are considered. These spatial mechanisms include different closing way： over-constraint appearing in rigid closure, in movable closure, and in dynamic closure as well; these examples also include two different new methods to solve this kind of issue： the way to recognize over-constraints by analyzing relative movement between two connected links and by constructing a virtual loop to recognize over-constraints. In addition, over-constraint determination tabulation is brought to analyze the motion couple. The researches above are all based upon the screw theory. All these multi-loop spatial mechanisms with different kinds of structures can completely be solved by following the directions and examples, and the new mobility theory based on the screw theory is also proved to be valid. This study not only enriches and develops the theory and makes the theory more universal, but also has a special meaning for innovation in mechanical engineering.
文摘This paper presents a design of boundary controllers implemented at the top end for global stabilization of a marine riser in a three dimensional space under environmental loadings. Based on the energy approach, nonlinear partial differential equations of motion, including bending-bending and longitudinal-bending couplings for the risers are derived. The couplings cause mutual effects between the three independent directions in the riser＇s motions, and make it difficult to minimize its vibrations. The Lyapunov direct method is employed to design the boundary controller. It is shown that the proposed boundary controllers can effectively reduce the riser＇s vibration. Stability analysis of the closed-loop system is performed using the Lyapunov direct method. Numerical simulations illustrate the results.
文摘A rigid flexible coupling physical model which can represent a flexible spacecraft is investigated in this paper. By applying the mechanics theory in a non-inertial coordinate system,the rigid flexible coupling dynamic model with dynamic stiffening is established via the subsystemmodeling framework. It is clearly elucidated for the first time that,dynamic stiffening is produced by the coupling effect of the centrifugal inertial load distributed on the beamand the transverse vibration deformation of the beam. The modeling approach in this paper successfully avoids problems which are caused by other popular modeling methods nowadays： the derivation process is too complex by using only one dynamic principle; a clearly theoretical explanation for dynamic stiffening can＇t be provided. First,the continuous dynamic models of the flexible beamand the central rigid body are established via structural dynamics and angular momentumtheory respectively. Then,based on the conclusions of orthogonalization about the normal constrained modes,the finite dimensional dynamic model suitable for controller design is obtained. The numerical simulation validations showthat： dynamic stiffening is successfully incorporated into the dynamic characteristics of the first-order model established in this paper,which can indicate the dynamic responses of the rigid flexible coupling system with large overall motion accurately,and has a clear modeling mechanism,concise expressions and a good convergence.
基金supported by the National Natural Science Foundation of China(52175270,91848204)the Project of Scientific and Technological Development Plan of Jilin Province(20220508130RC).
文摘Accurate knowledge of the kinematics of the in vivo Ankle Joint Complex(AJC)is critical for understanding the biomechanical function of the foot and assessing postoperative rehabilitation of ankle disorders,as well as an essential guide to the design of ankle–foot assistant devices.However,detailed analysis of the continuous 3D motion of the tibiotalar and subtalar joints during normal walking throughout the stance phase is still considered to be lacking.In this study,dynamic radiographs of the hindfoot were acquired from eight subjects during normal walking.Natural motions with six Degrees of Freedom(DOF)and the coupled patterns of the two joints were analyzed.It was found that the movements of the two joints were mostly in opposite directions(including rotation and translation),mainly in the early and late stages.There were significant differences in the Range of Motion(ROM)in Dorsiflexion/Plantarflexion(D/P),Inversion/Eversion(In/Ev),and Anterior–Posterior(AP)and Medial–Lateral(ML)translation of the tibiotalar and subtalar joints(p<0.05).Plantarflexion of the tibiotalar joint was coupled with eversion and posterior translation of the subtalar joint during the impact phase(R^(2)=0.87 and 0.86,respectively),and plantarflexion of the tibiotalar joint was coupled with inversion and anterior translation of the subtalar joint during the push-off phase(R^(2)=0.93 and 0.75,respectively).This coordinated coupled motion of the two joints may be a manifestation of the AJC to move flexibly while bearing weight and still have stability.
基金the National Natural Science Foundation of China(no.22173095)S.W.acknowledges the National Natural Science Foundation of China(no.52103021).
文摘Developing a dual-cross-linked network,with weaker cross-links to dissipate energy and stronger ones to sustain integrity,is an effective protocol to overcome the well-known trade-off between hardness and stretchability for achieving high toughness.Although this protocol has been extensively explored in the past two decades,the molecular mechanism underlying the protocol is yet to be better understood.In this study,we copolymerize hexyl methacrylate with hydrogen-bonding n-isopropyl methacrylamide and vitrimeric cross-linkers to prepare dual-cross-linked networks.During the tensile tests,the energy dissipation is greatly enhanced by increasing the density of hydrogen bonds,enabling the initial modulus to increase from∼1 MPa,which is typical for an elastomer,to 300 MPa,which is closer to the glass.Nevertheless,the breakup of the hydrogen bonds during the elongation significantly dissipates the energy,leading to the softening of the materials,thereby facilitating the stretch to high strain.The softening process,seen as an overshoot in the stress−strain curve,is well captured by the Dobrynin theory modified by Konkolewicz and co-workers upon including a strain rate-dependent element.The deviation at a high content of hydrogen bonds,where the distance between hydrogen bonds becomes smaller than the Kuhn length,is attributed to the coupled motion of the hydrogen bonds.
