High qualityβ-Ga_(2)O_(3)single crystal nanobelts with length of 2−3 mm and width from tens of microns to 132μm were synthesized by carbothermal reduction method.Based on the grown nanobelt with the length of 600μm...High qualityβ-Ga_(2)O_(3)single crystal nanobelts with length of 2−3 mm and width from tens of microns to 132μm were synthesized by carbothermal reduction method.Based on the grown nanobelt with the length of 600μm,the dual-Schottky-junctions coupling device(DSCD)was fabricated.Due to the electrically floating Ga_(2)O_(3)nanobelt region coupling with the double Schottky-junctions,the current I_(S2)increases firstly and rapidly reaches into saturation as increase the voltage V_(S2).The saturation current is about 10 pA,which is two orders of magnitude lower than that of a single Schottky-junction.In the case of solar-blind ultraviolet(UV)light irradiation,the photogenerated electrons further aggravate the coupling physical mechanism in device.I_(S2)increases as the intensity of UV light increases.Under the UV light of 1820μW/cm^(2),I_(S2)quickly enters the saturation state.At V_(S2)=10 V,photo-to-dark current ratio(PDCR)of the device reaches more than 104,the external quantum efficiency(EQE)is 1.6×10^(3)%,and the detectivity(D*)is 7.5×10^(12)Jones.In addition,the device has a very short rise and decay times of 25−54 ms under different positive and negative bias.DSCD shows unique electrical and optical control characteristics,which will open a new way for the application of nanobelt-based devices.展开更多
To know about the radiation effects on the super large array 9 k×9 k CCDs used in a space telescope induced by energetic protons,the experiments of the super large array 9 k×9 k charge coupled devices(CCDs)u...To know about the radiation effects on the super large array 9 k×9 k CCDs used in a space telescope induced by energetic protons,the experiments of the super large array 9 k×9 k charge coupled devices(CCDs)used in the space telescope irradiated by 60 MeV and 100 MeV protons are presented.The samples were exposed by 60 MeV and 100 MeV protons at fluences of 5×10^(9)/cm^(2) and 1×10^(10)/cm^(2),respectively.The degradations of the main performance parameters of the super large array CCDs which are paid special attention to the space telescope are investigated.The full well capacity,mean dark current,and the charge transfer inefficiency(CTI)versus proton fluence are presented,which are tested at very low temperature of-85℃.The annealing tests of 168 h were carried out after proton irradiation.The dark images before and after proton irradiation are also presented to compare the image degradation.The degradation mechanisms of the super large array CCDs irradiated by protons are analyzed.The experimental results show that the main performance parameters of the CCDs are degraded after 60 MeV and 100 MeV protons and the degradations induced by 60 MeV protons are larger than that induced by 100 MeV protons.The experimental results of the super large array CCDs irradiated by protons will provide the basic test data support for orbit life assessment of the space telescope.展开更多
Time delay and integration （TDI） charge coupled device （CCD） noise sets a fundamental limit on image sensor performance, especially under low illumination in remote sensing applications. After introducing the comp...Time delay and integration （TDI） charge coupled device （CCD） noise sets a fundamental limit on image sensor performance, especially under low illumination in remote sensing applications. After introducing the complete sources of CCD noise, we study the effects of TDI operation mode on noise, and the relationship between different types of noise and number of the TDI stage. Then we propose a new technique to identify and measure sources of TDI CCD noise employing mathematical statistics theory, where theoretical analysis shows that noise estimated formulation converges well. Finally, we establish a testing platform to carry out experiments, and a standard TDI CCD is calibrated by using the proposed method. The experimental results show that the noise analysis and measurement methods presented in this paper are useful for modeling TDI CCDs.展开更多
Objective： To observe the tested results of the segmental range of motion （ROM） of lumbar spine by charge couple device （CCD）-based system for 3-dimensional real-time positioning （CCD system）, and to analyze it...Objective： To observe the tested results of the segmental range of motion （ROM） of lumbar spine by charge couple device （CCD）-based system for 3-dimensional real-time positioning （CCD system）, and to analyze its clinical significance. Methods： Seven patients with lumbar joint dysfunction and 8 healthy subjects were tested twice by the CCD-based system with an interval of 10 min. Results： The ROM of the patients was obviously lesser than that of the healthy subjects. The measuring data of segmental ROM of lumbar spine by CCD system is correlated significantly to the same data checked later on the same subjects in every direction of the movements. The differences between two checks are usually less than 1 degree. Conclusion： Specially designed CCD based system for 3-dimensional real-time positioning could objectively reflect the segmental ROM of lumbar spine. The system would be of great clinical significance in the assessment of the biomechanical dysfunction of lumbar spine and the effect of the treatment applied.展开更多
To prevent a vehicle from departing the lane in assistant or automatic steering, real-time vision-based detection of lane is studied. The system architecture, detecting principle and lane model are described. Then the...To prevent a vehicle from departing the lane in assistant or automatic steering, real-time vision-based detection of lane is studied. The system architecture, detecting principle and lane model are described. Then the detecting algorithm of the lane image is discussed in detail. In this algorithm, several proper sub-windows in one image are first selected as the processing regions. To every sub-window, by means of such steps as appropriate pre-processing, edge detection and Hough transform, etc., the lane description features are extracted. Experimental results reveal that this detection method is of good real-time, high recognition reliability and strong robustness, etc., which can provide the decision-making foundation for the following automatic or assistant steering to some extent.展开更多
We outline probable and possible developments with wireless capsule endoscopy. It seems likely that capsule endoscopy will become increasingly effective in diagnostic gastrointestinal endoscopy. This will be attractiv...We outline probable and possible developments with wireless capsule endoscopy. It seems likely that capsule endoscopy will become increasingly effective in diagnostic gastrointestinal endoscopy. This will be attractive to patients especially for cancer or varices detection because capsule endoscopy is painless and is likely to have a higher take up rate compared to conventional colonoscopy and gastroscopy. Double imager capsules with increased frame rates have been used to image the esophagus for Barrett's and esophageal varices. The image quality is not bad but needs to be improved if it is to become a realistic substitute for flexible upper and lower gastrointestinal endoscopy. An increase in the frame rate, angle of view, depth of field, image numbers, duration of the procedure and improvements in illumination seem likely. Colonic, esophageal and gastric capsules will improve in quality, eroding the supremacy of flexible endoscopy, and become embedded into screening programs. Therapeutic capsules will emerge with brushing, cytology, fluid aspiration, biopsy and drug delivery capabilities. Electrocautery may also become possible. Diagnostic capsules will integrate physiological measurements with imaging and optical biopsy, and immunologic cancer recognition. Remote control movement will improve with the use of magnets and/or electrostimulation and perhaps electromechanical methods. External wireless commands will influence capsule diagnosis and therapy and will increasingly entail the use of real-time imaging. However, it should be noted that speculations about the future of technology in any detail are almost always wrong.展开更多
This paper presents an automatic system of vehicle number-plate recognition based on neural networks. In this system, location of number-plate and recognition of characters in number-plate can be automatically complet...This paper presents an automatic system of vehicle number-plate recognition based on neural networks. In this system, location of number-plate and recognition of characters in number-plate can be automatically completed. Pixel colors of Number-plate area are classified using neural network, then color features are extracted by analyzing scanning lines of the cross-section of number-plate. It takes full use of number-plate color features to locate number-plate. Characters in number-plate can be effectively recognized using the neural networks. Experimental results show that the correct rate of number-plate location is close to 100%, and the time of number-plate location is less than 1 second. Moreover, recognition rate of characters is improved due to the known number-plate type. It is also observed that this system is not sensitive to variations of weather, illumination and vehicle speed. In addition, and also the size of number-plate need not to be known in prior. This system is of crucial significance to apply and spread the automatic system of vehicle number-plate recognition.展开更多
In order to improve the test accuracy of CCD,a new type of CCD device is proposed.Several columns(rows) of photoelectric diodes(PDs) are combined together,and staggered with the distance of H1=H/N,where H is the space...In order to improve the test accuracy of CCD,a new type of CCD device is proposed.Several columns(rows) of photoelectric diodes(PDs) are combined together,and staggered with the distance of H1=H/N,where H is the space between two adjacent PDs,and N is the number of columns(rows).The photoelectric signals are collected simultaneously by multi-channel A/D,and the accurate measurement result is obtained through appropriate signal processing.Without changing the size or space of PDs,more photographic pixels are arranged in the given direction within a finite length.Diameters of three standard poles are measured by a single CCD and two staggered CCDs,respectively with length of 30 mm and diameters of 5 mm,8 mm and 12 mm,respectively.The results show that the accuracy of double staggered CCDs is two times of that of single CCD.The new type of CCDs can avoid the impact of PD space theoretically and higher measurement accuracy can be obtained.展开更多
A stable and homogeneous well-aligned air microplasma device for application at atmospheric pressure is designed and its electrical and optical characteristics are investigated. Current-voltage measurements and intens...A stable and homogeneous well-aligned air microplasma device for application at atmospheric pressure is designed and its electrical and optical characteristics are investigated. Current-voltage measurements and intensified charge coupled device （ICCD） images show that the well-aligned air microplasma device is able to generate a large-area and homogeneous discharge at the applied voltages ranging from 12 kV to 14 kV, with a repetition frequency of 5 kHz, which is attributed to the diffusion effect of plasma on dielectric surface. Moreover, this well-aligned microplasma device may result in the uniform and large-area surface modification of heat-sensitive PET polymers without damage, such as optimization in hydrophobicity and biocompatibility. In the biomedical field, the utility of this well-aligned microplasma device is further testified. It proves to be very efficient for the large-area and uniform inactivation of E. coli cells with a density of 103/cm2 on LB agar plate culture medium, and inactivation efficiency can reach up to 99% for 2-min treatment.展开更多
In order to realize fast maneuvering imaging of the target area with high resolution agile satellite, a new attitude matching algorithm is developed. A strict mosaic imaging model of ray trace and the velocity vector ...In order to realize fast maneuvering imaging of the target area with high resolution agile satellite, a new attitude matching algorithm is developed. A strict mosaic imaging model of ray trace and the velocity vector mapping are built according to the strip mosaic imaging principle and the relationship between imaging target and the camera focal plane. The three-axis attitude is deduced based on the principle of optimal tracking of the maneuvering path. Finally, the geometric scaling simulation is carried out through the time delayed and integration(TDI) charge coupled device(CCD) prototype system, satellite attitude control physical simulation platform and the LED earth target simulator. The experimental results show that the algorithm could realize the matching band seamless splicing imaging of the target very well, confirming the correctness of the algorithm.展开更多
The existence and propagation of transverse surface waves in piezoelectric coupled solids is investigated, in which perfect bonding between a metal/dielectric substrate and a piezoelectric layer of finite-thickness is...The existence and propagation of transverse surface waves in piezoelectric coupled solids is investigated, in which perfect bonding between a metal/dielectric substrate and a piezoelectric layer of finite-thickness is assumed. Dis- persion equations relating phase velocity to material con- stants for the existence of various modes are obtained in a simple mathematical form for a piezoelectric material of class 6mm. It is discovered and proved by numerical examples in this paper that a novel Bleustein-Gulyaev （B-G） type of transverse surface wave can exist in such piezoelectric cou- pled solid media when the bulk-shear-wave velocity in the substrate is less than that in the piezoelectric layer but greater than the corresponding B-G wave velocity in the same pie- zoelectric material with an electroded surface. Such a wave does not exist in such layered structures in the absence of pie- zoelectricity. The mode shapes for displacement and electric potential in the piezoelectric layer are obtained and discussed theoretically. The study extends the regime of transverse sur- face waves and may lead to potential applications to surface acoustic wave devices.展开更多
Measurements of wave heights with image sequences from a Charged Coupled Device(CCD) camera were made. Sinusoidal, as well as unidirectional and directional, waves were used for the experiments. A transfer function wa...Measurements of wave heights with image sequences from a Charged Coupled Device(CCD) camera were made. Sinusoidal, as well as unidirectional and directional, waves were used for the experiments. A transfer function was obtained by calibration of the magnitudes of the gray values of the images against the results of wave gauge measurements for directional waves. With this transfer function, wave heights for regular waves were deduced. It is shown that the average relative errors are smaller than 16% for both unidirectional and directional waves.展开更多
A new 128×128 element PtSi Schottky barrier infrared image sensor with ITCCD readout structure and PtSi thin film optical cavity detector structure has been fabricated,which has 50μm×50 μm pixels,a fill fa...A new 128×128 element PtSi Schottky barrier infrared image sensor with ITCCD readout structure and PtSi thin film optical cavity detector structure has been fabricated,which has 50μm×50 μm pixels,a fill factor of 40 percent,the nonuniformity of 5% or less and the dynamic range of over or equal to 50 dB.The noise equivalent temperature difference is 0.2 K with f/1.0 optics at 300 K background. In this paper,the principle of operation,design consideration and fabrication technology for the device are described.展开更多
The time delay integration charge coupled device(TDI CCD)is the key component in remote sensing systems.The paper analyzes the structure and the working principles of the device according to a customized TDI CCD chip....The time delay integration charge coupled device(TDI CCD)is the key component in remote sensing systems.The paper analyzes the structure and the working principles of the device according to a customized TDI CCD chip.Employing the special clock resources and large-scale phase locked logic(PLL)in field-programmable gate arrays(FPGA),a timing-driven approach is proposed,using which all timing signals including reset gate,horizontal and vertical timing signals,are implemented in one chip.This not only reduces printed circuit board(PCB)space,but also enhances the portability of the system.By studying and calculating CCD parameters thoroughly,load capacity and power consumption,package,etc,are compared between various candidates chips,and detailed comparison results are also listed in table.Experimental results show that clock generator and driving circuit satisfy the requirements of high speed TDI CCD.展开更多
With the requirements of multimedia service increasing in people＇ s life, sensor modules such as microphone, camera are added in the smart home＇ s sensor network, and the acquisition and processing of a large amount...With the requirements of multimedia service increasing in people＇ s life, sensor modules such as microphone, camera are added in the smart home＇ s sensor network, and the acquisition and processing of a large amount of information media such as audio, image and video is becoming a significant characteristics of smart home. The paper focuses on solving the following technical problems： the building of Zigbee multimedia network, the Design and selection of multimedia sensor node. These provide the basic network platform and the core technical support for the building of smart home.展开更多
Scintillators are high-density luminescent materials that convert X-rays to visible light. Thallium doped cesium iodide (CsI:Tl) scintillation materials are widely used as converters for X-rays into visible light, wit...Scintillators are high-density luminescent materials that convert X-rays to visible light. Thallium doped cesium iodide (CsI:Tl) scintillation materials are widely used as converters for X-rays into visible light, with very high conversion efficiency of 64.000 optical photons/MeV. CsI:Tl crystals are commercially available, but, the possibility of developing these crystals into different geometric shapes, meeting the need for coupling the photosensor and reducing cost, makes this material very attractive for scientific research. The objective of this work was to study the feasibility of using radiation sensors, scintillators type, developed for use in imaging systems for X-rays. In this paper, the CsI:Tl scintillator crystal with nominal concentration of the 10-3 M was grown by the vertical Bridgman technique. The imaging performance of CsI:Tl scintillator was studied as a function of the design type and thickness, since it interferes with the light scattering and, hence, the detection efficiency plus final image resolution. The result of the diffraction X-ray analysis in the grown crystals was consistent with the pattern of a face-centered cubic (fcc) crystal structure. Slices 25 × 2 × 3 mm3 (length, thickness, height) of the crystal and mini crystals of 1 × 2 × 3 mm3 (length, thickness, height) were used for comparison in the imaging systems for X-rays. With these crystals scintillators, images of undesirable elements, such as metals in food packaging, were obtained. One-dimensional array of photodiodes and the photosensor CCD (Coupled Charge Device) component were used. In order to determine the ideal thickness of the slices of the scintillator crystal CsI:Tl, Monte Carlo method was used.展开更多
A Princeton Instruments PI-LCX 1300 charge-coupled device （CCD） camera used for X-ray spectrum measurements in laser-plasma experiments is calibrated using three radioactive sources and investigated with the Monte C...A Princeton Instruments PI-LCX 1300 charge-coupled device （CCD） camera used for X-ray spectrum measurements in laser-plasma experiments is calibrated using three radioactive sources and investigated with the Monte Carlo code Geant4. The exposure level is controlled to make the CCD work in single photon counting mode. A summation algorithm for obtaining accurate X-ray spectra is developed to reconstruct the X-ray spectra, and the results show that the developed algorithm effectively reduces the low-energy tail caused by split pixel events. The obtained CCD energy response shows good linearity. The detection efficiency curves from both Monte Carlo simulations and the manufacturer agree well with the experimental results. This consistency demonstrates that event losses in charge collection processes are negligible when the developed summation algorithm of sDlit Dixel events is emDloved.展开更多
A novel spectral calibration method is developed for spectral domain optical coherence tomography system. The method is based on two measurements of interference spectra from two reference mirror positions. It removes...A novel spectral calibration method is developed for spectral domain optical coherence tomography system. The method is based on two measurements of interference spectra from two reference mirror positions. It removes the influence of dispersion mismatch, and hence accurately determines the spectral distribution on the line-scan charge-coupled device （CCD） for sequent precise interpolation. High quality imaging can be realized with this method. Elimination of the degradation effect caused by dispersion mismatch is verified experimentally, and improved two-dimensional （2D） imaging of fresh orange pulp based on the proposed spectral calibration method is demonstrated.展开更多
For space optical remote sensor (SORS) with either film or time delay and integrate charge coupled device (TDI-CCD) imaging, in order to achieve higher resolution it requires more accurate real-time image motion compe...For space optical remote sensor (SORS) with either film or time delay and integrate charge coupled device (TDI-CCD) imaging, in order to achieve higher resolution it requires more accurate real-time image motion compensation. This primarily depends on real-time computation of the image motion velocity vector (IMVV) and error budget and synthesis on related parameters. An effective modeling scheme is introduced and the derivation of IMVV equation, error budget and synthesis by Monte-Carlo method are presented in detail. This total solution was applied to SORS system test on orbit and has been confirmed to be very accurate based on the resolution, transfer function at Nyquist frequency, signal-to-noise ratio and average gray scale of the captured images.展开更多
基金supported by Natural Science Basic Research Program in Shaanxi Province of China(No.2023-JCYB-574)National Natural Science Foundation of China(No.62204203).
文摘High qualityβ-Ga_(2)O_(3)single crystal nanobelts with length of 2−3 mm and width from tens of microns to 132μm were synthesized by carbothermal reduction method.Based on the grown nanobelt with the length of 600μm,the dual-Schottky-junctions coupling device(DSCD)was fabricated.Due to the electrically floating Ga_(2)O_(3)nanobelt region coupling with the double Schottky-junctions,the current I_(S2)increases firstly and rapidly reaches into saturation as increase the voltage V_(S2).The saturation current is about 10 pA,which is two orders of magnitude lower than that of a single Schottky-junction.In the case of solar-blind ultraviolet(UV)light irradiation,the photogenerated electrons further aggravate the coupling physical mechanism in device.I_(S2)increases as the intensity of UV light increases.Under the UV light of 1820μW/cm^(2),I_(S2)quickly enters the saturation state.At V_(S2)=10 V,photo-to-dark current ratio(PDCR)of the device reaches more than 104,the external quantum efficiency(EQE)is 1.6×10^(3)%,and the detectivity(D*)is 7.5×10^(12)Jones.In addition,the device has a very short rise and decay times of 25−54 ms under different positive and negative bias.DSCD shows unique electrical and optical control characteristics,which will open a new way for the application of nanobelt-based devices.
基金The National Science Foundation of China(U2167208,11875223)Natural Science Basic Research Program of Shaanxi(2024JC-JCQN)The Foundation of State Key Laboratory of China(NKLIPR2320)。
文摘To know about the radiation effects on the super large array 9 k×9 k CCDs used in a space telescope induced by energetic protons,the experiments of the super large array 9 k×9 k charge coupled devices(CCDs)used in the space telescope irradiated by 60 MeV and 100 MeV protons are presented.The samples were exposed by 60 MeV and 100 MeV protons at fluences of 5×10^(9)/cm^(2) and 1×10^(10)/cm^(2),respectively.The degradations of the main performance parameters of the super large array CCDs which are paid special attention to the space telescope are investigated.The full well capacity,mean dark current,and the charge transfer inefficiency(CTI)versus proton fluence are presented,which are tested at very low temperature of-85℃.The annealing tests of 168 h were carried out after proton irradiation.The dark images before and after proton irradiation are also presented to compare the image degradation.The degradation mechanisms of the super large array CCDs irradiated by protons are analyzed.The experimental results show that the main performance parameters of the CCDs are degraded after 60 MeV and 100 MeV protons and the degradations induced by 60 MeV protons are larger than that induced by 100 MeV protons.The experimental results of the super large array CCDs irradiated by protons will provide the basic test data support for orbit life assessment of the space telescope.
基金Project supported by the National High Technology Research and Development Program of China (Grant No. 2006AA06A208)
文摘Time delay and integration （TDI） charge coupled device （CCD） noise sets a fundamental limit on image sensor performance, especially under low illumination in remote sensing applications. After introducing the complete sources of CCD noise, we study the effects of TDI operation mode on noise, and the relationship between different types of noise and number of the TDI stage. Then we propose a new technique to identify and measure sources of TDI CCD noise employing mathematical statistics theory, where theoretical analysis shows that noise estimated formulation converges well. Finally, we establish a testing platform to carry out experiments, and a standard TDI CCD is calibrated by using the proposed method. The experimental results show that the noise analysis and measurement methods presented in this paper are useful for modeling TDI CCDs.
文摘Objective： To observe the tested results of the segmental range of motion （ROM） of lumbar spine by charge couple device （CCD）-based system for 3-dimensional real-time positioning （CCD system）, and to analyze its clinical significance. Methods： Seven patients with lumbar joint dysfunction and 8 healthy subjects were tested twice by the CCD-based system with an interval of 10 min. Results： The ROM of the patients was obviously lesser than that of the healthy subjects. The measuring data of segmental ROM of lumbar spine by CCD system is correlated significantly to the same data checked later on the same subjects in every direction of the movements. The differences between two checks are usually less than 1 degree. Conclusion： Specially designed CCD based system for 3-dimensional real-time positioning could objectively reflect the segmental ROM of lumbar spine. The system would be of great clinical significance in the assessment of the biomechanical dysfunction of lumbar spine and the effect of the treatment applied.
文摘To prevent a vehicle from departing the lane in assistant or automatic steering, real-time vision-based detection of lane is studied. The system architecture, detecting principle and lane model are described. Then the detecting algorithm of the lane image is discussed in detail. In this algorithm, several proper sub-windows in one image are first selected as the processing regions. To every sub-window, by means of such steps as appropriate pre-processing, edge detection and Hough transform, etc., the lane description features are extracted. Experimental results reveal that this detection method is of good real-time, high recognition reliability and strong robustness, etc., which can provide the decision-making foundation for the following automatic or assistant steering to some extent.
文摘We outline probable and possible developments with wireless capsule endoscopy. It seems likely that capsule endoscopy will become increasingly effective in diagnostic gastrointestinal endoscopy. This will be attractive to patients especially for cancer or varices detection because capsule endoscopy is painless and is likely to have a higher take up rate compared to conventional colonoscopy and gastroscopy. Double imager capsules with increased frame rates have been used to image the esophagus for Barrett's and esophageal varices. The image quality is not bad but needs to be improved if it is to become a realistic substitute for flexible upper and lower gastrointestinal endoscopy. An increase in the frame rate, angle of view, depth of field, image numbers, duration of the procedure and improvements in illumination seem likely. Colonic, esophageal and gastric capsules will improve in quality, eroding the supremacy of flexible endoscopy, and become embedded into screening programs. Therapeutic capsules will emerge with brushing, cytology, fluid aspiration, biopsy and drug delivery capabilities. Electrocautery may also become possible. Diagnostic capsules will integrate physiological measurements with imaging and optical biopsy, and immunologic cancer recognition. Remote control movement will improve with the use of magnets and/or electrostimulation and perhaps electromechanical methods. External wireless commands will influence capsule diagnosis and therapy and will increasingly entail the use of real-time imaging. However, it should be noted that speculations about the future of technology in any detail are almost always wrong.
基金the Key Development Plan Project of Science and Technology (No.991p0111).
文摘This paper presents an automatic system of vehicle number-plate recognition based on neural networks. In this system, location of number-plate and recognition of characters in number-plate can be automatically completed. Pixel colors of Number-plate area are classified using neural network, then color features are extracted by analyzing scanning lines of the cross-section of number-plate. It takes full use of number-plate color features to locate number-plate. Characters in number-plate can be effectively recognized using the neural networks. Experimental results show that the correct rate of number-plate location is close to 100%, and the time of number-plate location is less than 1 second. Moreover, recognition rate of characters is improved due to the known number-plate type. It is also observed that this system is not sensitive to variations of weather, illumination and vehicle speed. In addition, and also the size of number-plate need not to be known in prior. This system is of crucial significance to apply and spread the automatic system of vehicle number-plate recognition.
基金supported by the National Natural Science Foundation of China (No.51005188)the Fund of Key Laboratory of Manufacturing and Automation of Xihua University (No.SZJJ2009-023)the University Talent Foundation of Xihua University (No.R0720221)
文摘In order to improve the test accuracy of CCD,a new type of CCD device is proposed.Several columns(rows) of photoelectric diodes(PDs) are combined together,and staggered with the distance of H1=H/N,where H is the space between two adjacent PDs,and N is the number of columns(rows).The photoelectric signals are collected simultaneously by multi-channel A/D,and the accurate measurement result is obtained through appropriate signal processing.Without changing the size or space of PDs,more photographic pixels are arranged in the given direction within a finite length.Diameters of three standard poles are measured by a single CCD and two staggered CCDs,respectively with length of 30 mm and diameters of 5 mm,8 mm and 12 mm,respectively.The results show that the accuracy of double staggered CCDs is two times of that of single CCD.The new type of CCDs can avoid the impact of PD space theoretically and higher measurement accuracy can be obtained.
基金supported by the Natural Science Foundation of Fujian Province,China(Grant No.2014J01025)the National Natural Science Foundation of China(Grant No.11275261)+1 种基金the Natural Science Foundation of Guangdong Province,China(Grant No.2015A030313005)the Fund from the Fujian Provincia Key Laboratory for Plasma and Magnetic Resonance,China
文摘A stable and homogeneous well-aligned air microplasma device for application at atmospheric pressure is designed and its electrical and optical characteristics are investigated. Current-voltage measurements and intensified charge coupled device （ICCD） images show that the well-aligned air microplasma device is able to generate a large-area and homogeneous discharge at the applied voltages ranging from 12 kV to 14 kV, with a repetition frequency of 5 kHz, which is attributed to the diffusion effect of plasma on dielectric surface. Moreover, this well-aligned microplasma device may result in the uniform and large-area surface modification of heat-sensitive PET polymers without damage, such as optimization in hydrophobicity and biocompatibility. In the biomedical field, the utility of this well-aligned microplasma device is further testified. It proves to be very efficient for the large-area and uniform inactivation of E. coli cells with a density of 103/cm2 on LB agar plate culture medium, and inactivation efficiency can reach up to 99% for 2-min treatment.
基金supported by the Youth Innovation Promotion Association(No.2017261)
文摘In order to realize fast maneuvering imaging of the target area with high resolution agile satellite, a new attitude matching algorithm is developed. A strict mosaic imaging model of ray trace and the velocity vector mapping are built according to the strip mosaic imaging principle and the relationship between imaging target and the camera focal plane. The three-axis attitude is deduced based on the principle of optimal tracking of the maneuvering path. Finally, the geometric scaling simulation is carried out through the time delayed and integration(TDI) charge coupled device(CCD) prototype system, satellite attitude control physical simulation platform and the LED earth target simulator. The experimental results show that the algorithm could realize the matching band seamless splicing imaging of the target very well, confirming the correctness of the algorithm.
基金supported by the National Natural Science Foundation of China(10972171)the Program for New Century Excellent Talents in Universities(NCET-08-0429)
文摘The existence and propagation of transverse surface waves in piezoelectric coupled solids is investigated, in which perfect bonding between a metal/dielectric substrate and a piezoelectric layer of finite-thickness is assumed. Dis- persion equations relating phase velocity to material con- stants for the existence of various modes are obtained in a simple mathematical form for a piezoelectric material of class 6mm. It is discovered and proved by numerical examples in this paper that a novel Bleustein-Gulyaev （B-G） type of transverse surface wave can exist in such piezoelectric cou- pled solid media when the bulk-shear-wave velocity in the substrate is less than that in the piezoelectric layer but greater than the corresponding B-G wave velocity in the same pie- zoelectric material with an electroded surface. Such a wave does not exist in such layered structures in the absence of pie- zoelectricity. The mode shapes for displacement and electric potential in the piezoelectric layer are obtained and discussed theoretically. The study extends the regime of transverse sur- face waves and may lead to potential applications to surface acoustic wave devices.
基金This work was financially supported by the Science Council, Taiwan (Project No. NSC 91 2611 E 019 007)
文摘Measurements of wave heights with image sequences from a Charged Coupled Device(CCD) camera were made. Sinusoidal, as well as unidirectional and directional, waves were used for the experiments. A transfer function was obtained by calibration of the magnitudes of the gray values of the images against the results of wave gauge measurements for directional waves. With this transfer function, wave heights for regular waves were deduced. It is shown that the average relative errors are smaller than 16% for both unidirectional and directional waves.
文摘A new 128×128 element PtSi Schottky barrier infrared image sensor with ITCCD readout structure and PtSi thin film optical cavity detector structure has been fabricated,which has 50μm×50 μm pixels,a fill factor of 40 percent,the nonuniformity of 5% or less and the dynamic range of over or equal to 50 dB.The noise equivalent temperature difference is 0.2 K with f/1.0 optics at 300 K background. In this paper,the principle of operation,design consideration and fabrication technology for the device are described.
基金National High Technology Research and Development Program of China(863 Program)(No.2009AA7010102)
文摘The time delay integration charge coupled device(TDI CCD)is the key component in remote sensing systems.The paper analyzes the structure and the working principles of the device according to a customized TDI CCD chip.Employing the special clock resources and large-scale phase locked logic(PLL)in field-programmable gate arrays(FPGA),a timing-driven approach is proposed,using which all timing signals including reset gate,horizontal and vertical timing signals,are implemented in one chip.This not only reduces printed circuit board(PCB)space,but also enhances the portability of the system.By studying and calculating CCD parameters thoroughly,load capacity and power consumption,package,etc,are compared between various candidates chips,and detailed comparison results are also listed in table.Experimental results show that clock generator and driving circuit satisfy the requirements of high speed TDI CCD.
文摘With the requirements of multimedia service increasing in people＇ s life, sensor modules such as microphone, camera are added in the smart home＇ s sensor network, and the acquisition and processing of a large amount of information media such as audio, image and video is becoming a significant characteristics of smart home. The paper focuses on solving the following technical problems： the building of Zigbee multimedia network, the Design and selection of multimedia sensor node. These provide the basic network platform and the core technical support for the building of smart home.
基金FAPESP(Foundation Research of the State of Sao Paulo)for financial support.
文摘Scintillators are high-density luminescent materials that convert X-rays to visible light. Thallium doped cesium iodide (CsI:Tl) scintillation materials are widely used as converters for X-rays into visible light, with very high conversion efficiency of 64.000 optical photons/MeV. CsI:Tl crystals are commercially available, but, the possibility of developing these crystals into different geometric shapes, meeting the need for coupling the photosensor and reducing cost, makes this material very attractive for scientific research. The objective of this work was to study the feasibility of using radiation sensors, scintillators type, developed for use in imaging systems for X-rays. In this paper, the CsI:Tl scintillator crystal with nominal concentration of the 10-3 M was grown by the vertical Bridgman technique. The imaging performance of CsI:Tl scintillator was studied as a function of the design type and thickness, since it interferes with the light scattering and, hence, the detection efficiency plus final image resolution. The result of the diffraction X-ray analysis in the grown crystals was consistent with the pattern of a face-centered cubic (fcc) crystal structure. Slices 25 × 2 × 3 mm3 (length, thickness, height) of the crystal and mini crystals of 1 × 2 × 3 mm3 (length, thickness, height) were used for comparison in the imaging systems for X-rays. With these crystals scintillators, images of undesirable elements, such as metals in food packaging, were obtained. One-dimensional array of photodiodes and the photosensor CCD (Coupled Charge Device) component were used. In order to determine the ideal thickness of the slices of the scintillator crystal CsI:Tl, Monte Carlo method was used.
基金supported by the National Natural Science Foundation of China(Nos.10975121,10905051,10902051,and 11174259)the Foundation of CAEP(Nos.2009A0102003 and 2011B0102021)the Foundation of Science and Technology on Plasma Physics Laboratory(No.9140C6802041004)
文摘A Princeton Instruments PI-LCX 1300 charge-coupled device （CCD） camera used for X-ray spectrum measurements in laser-plasma experiments is calibrated using three radioactive sources and investigated with the Monte Carlo code Geant4. The exposure level is controlled to make the CCD work in single photon counting mode. A summation algorithm for obtaining accurate X-ray spectra is developed to reconstruct the X-ray spectra, and the results show that the developed algorithm effectively reduces the low-energy tail caused by split pixel events. The obtained CCD energy response shows good linearity. The detection efficiency curves from both Monte Carlo simulations and the manufacturer agree well with the experimental results. This consistency demonstrates that event losses in charge collection processes are negligible when the developed summation algorithm of sDlit Dixel events is emDloved.
基金supported by the National"863"Project of China(No.2006AA02Z4E0,2008AA02Z422)the National Natural Science Foundation of China(No.60378041,60478040)+1 种基金the Natural Science Foundation of Zhejiang Province(No.Z603003)the Program for New Century Excellent Talents in University(NCET-04-0528).
文摘A novel spectral calibration method is developed for spectral domain optical coherence tomography system. The method is based on two measurements of interference spectra from two reference mirror positions. It removes the influence of dispersion mismatch, and hence accurately determines the spectral distribution on the line-scan charge-coupled device （CCD） for sequent precise interpolation. High quality imaging can be realized with this method. Elimination of the degradation effect caused by dispersion mismatch is verified experimentally, and improved two-dimensional （2D） imaging of fresh orange pulp based on the proposed spectral calibration method is demonstrated.
文摘For space optical remote sensor (SORS) with either film or time delay and integrate charge coupled device (TDI-CCD) imaging, in order to achieve higher resolution it requires more accurate real-time image motion compensation. This primarily depends on real-time computation of the image motion velocity vector (IMVV) and error budget and synthesis on related parameters. An effective modeling scheme is introduced and the derivation of IMVV equation, error budget and synthesis by Monte-Carlo method are presented in detail. This total solution was applied to SORS system test on orbit and has been confirmed to be very accurate based on the resolution, transfer function at Nyquist frequency, signal-to-noise ratio and average gray scale of the captured images.
