Soil desiccation cracking is a prevalent natural phenomenon that poses significant geotechnical and geoenvironmental challenges.Cracks typically initiate at surface defects such as air bubbles,large aggregates,tiny pi...Soil desiccation cracking is a prevalent natural phenomenon that poses significant geotechnical and geoenvironmental challenges.Cracks typically initiate at surface defects such as air bubbles,large aggregates,tiny pits,or uneven surfaces,where localized stress concentrations are readily induced.This study conducted a series of laboratory desiccation tests on slurry samples to investigate the initiation and propagation of desiccation cracks in the presence of varying types and quantities of surface defects.Digital image correlation(DIC)technology was employed to monitor the strain and displacement fields on the soil surface during the desiccation process.The results reveal that strain and displacement data derived from DIC can precisely predict the initiation sites and propagation directions of desiccation cracks.In samples with internal defects,cracks predominantly propagate through the defect,whereas external defects tend to initiate cracks along their edges.In samples with multiple defects,Y-shaped crack patterns generally form initially,followed by T-shaped and straight cracks,driven by the evolving stress field.The dynamic interplay between crack formation and tensile stress redistribution governs the initiation and propagation of desiccation cracks.展开更多
Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent...Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent properties of natural layered rock masses.In this paper,soft-hard interbedded rock masses with different dip angles were prepared based on 3D printing(3DP)sand core technology.Uniaxial compression creep tests were conducted to investigate its anisotropic creep behavior based on digital imaging correlation(DIC)technology.The results show that the anisotropic creep behavior of the 3DP soft-hard interbedded rock mass is mainly affected by the dip angles of the weak interlayer when the stress is at low levels.As the stress level increases,the effect of creep stress on its creep anisotropy increases significantly,and the dip angle is no longer the main factor.The minimum value of the long-term strength and creep failure strength always appears in the weak interlayer within 30°–60°,which explains why the failure of the layered rock mass is controlled by the weak interlayer and generally emerges at 45°.The tests results are verified by comparing with theoretical and other published studies.The feasibility of the 3DP soft-hard interbedded rock mass provides broad prospects and application values for 3DP technology in future experimental research.展开更多
In this paper,the occurrence and development mechanism of strain on the cross-section during the wood drying is explored.Therefore,strain regularity on the cross-section of 50 mm thickness elm(Ulmus rubra)board at the...In this paper,the occurrence and development mechanism of strain on the cross-section during the wood drying is explored.Therefore,strain regularity on the cross-section of 50 mm thickness elm(Ulmus rubra)board at the temperature of 40℃and 80℃is detected via digital image correlation technology.Hence,the difference between tangential and radial strain at surface and core layers was denoted.The results showed that strain distribution in the width direction of the board is uneven.Moreover,a large drying shrinkage strain occurs at the near-core layer,while the maximum strain difference reaches 4.08%.Hence,the surface of the board is cracked along the thickness direction.The radial strain of the board is higher than the tangential strain in the early stage of drying,while these strains are reversed in the later stage of drying.The temperature is related to the difference between the tangential and radial strains of the elm board.These differences at the core layer are larger than those of the surface layer.The conducted research results provide a theoretical basis for process optimization.展开更多
[Objectives]To explore the correlation of processing technology,physical parameters and chemical components during plain stir-baking of Trichosanthis Radix.[Methods]Based on mixture uniform experiment design,the Trich...[Objectives]To explore the correlation of processing technology,physical parameters and chemical components during plain stir-baking of Trichosanthis Radix.[Methods]Based on mixture uniform experiment design,the Trichosanthis Radix was prepared by plain stir-bake method.Delphi method was used to evaluate and select the highest-scoring processed product for measuring physical parameters.UV spectrophotometry was used to determine the contents of starch and polysaccharide.The correlation and linear regression model of processing technology,physical parameters and chemical components were established with the aid of SPSS 26.0[Results]After processing by plain stir-bake method,the relative density and chromaticity showed a decreasing trend in the processed products of Trichosanthis Radix,the oxidation value,hydroscopic rate and swelling decreased firstly and then increased,and pH increased firstly and then decreased.The content of total starch decreased,the content of polysaccharide increased,and there was a negative correlation between them.There was a significant positive correlation between temperature and oxidation value,swelling and hydroscopic rate,hydroscopic rate and polysaccharide,and there was a significant negative correlation between relative density and hydroscopic rate or polysaccharide,total starch and hydroscopic rate or swelling.The linear relation model between processing technology and physical parameters and chemical components was r2>0.9.[Conclusions]After processing by plain stir-bake method,the physical parameters of Trichosanthis Radix changed,and there may be mutual conversion between total starch and polysaccharides.To a certain extent,physical parameters can be used to evaluate the quality of processed products of Trichosanthis Radix.This study is expected to provide a reference for research on quality evaluation of processed products of traditional Chinese medicine.展开更多
Signals from infrared detector are very weak in SO2 concentration measuring system.In order to improve the sensitivity of detection,combining with filter correlation technology and infrared absorption principle,the we...Signals from infrared detector are very weak in SO2 concentration measuring system.In order to improve the sensitivity of detection,combining with filter correlation technology and infrared absorption principle,the weak signal processing circuit is designed according to correlation detection technology.Under laboratory conditions,system performance of SO2 concentration is tested,and the experimental data are analyzed and processed.Then relationship of SO2 concentration and the measuring voltage is provided to prove that the design improves measuring sensitivity of the system.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.42525201,42230710,42407521).
文摘Soil desiccation cracking is a prevalent natural phenomenon that poses significant geotechnical and geoenvironmental challenges.Cracks typically initiate at surface defects such as air bubbles,large aggregates,tiny pits,or uneven surfaces,where localized stress concentrations are readily induced.This study conducted a series of laboratory desiccation tests on slurry samples to investigate the initiation and propagation of desiccation cracks in the presence of varying types and quantities of surface defects.Digital image correlation(DIC)technology was employed to monitor the strain and displacement fields on the soil surface during the desiccation process.The results reveal that strain and displacement data derived from DIC can precisely predict the initiation sites and propagation directions of desiccation cracks.In samples with internal defects,cracks predominantly propagate through the defect,whereas external defects tend to initiate cracks along their edges.In samples with multiple defects,Y-shaped crack patterns generally form initially,followed by T-shaped and straight cracks,driven by the evolving stress field.The dynamic interplay between crack formation and tensile stress redistribution governs the initiation and propagation of desiccation cracks.
基金the support of the National Natural Science Foundation of China(Grant Nos.42207199,52179113,42272333)Zhejiang Postdoctoral Scientific Research Project(Grant Nos.ZJ2022155,ZJ2022156)。
文摘Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent properties of natural layered rock masses.In this paper,soft-hard interbedded rock masses with different dip angles were prepared based on 3D printing(3DP)sand core technology.Uniaxial compression creep tests were conducted to investigate its anisotropic creep behavior based on digital imaging correlation(DIC)technology.The results show that the anisotropic creep behavior of the 3DP soft-hard interbedded rock mass is mainly affected by the dip angles of the weak interlayer when the stress is at low levels.As the stress level increases,the effect of creep stress on its creep anisotropy increases significantly,and the dip angle is no longer the main factor.The minimum value of the long-term strength and creep failure strength always appears in the weak interlayer within 30°–60°,which explains why the failure of the layered rock mass is controlled by the weak interlayer and generally emerges at 45°.The tests results are verified by comparing with theoretical and other published studies.The feasibility of the 3DP soft-hard interbedded rock mass provides broad prospects and application values for 3DP technology in future experimental research.
基金supported by the National Natural Science Foundation of China(No.31901242)Heilongjiang Science Foundation Project(No.LH2020C038)National Undergraduate Training Programs for Innovations(No.202110225074)。
文摘In this paper,the occurrence and development mechanism of strain on the cross-section during the wood drying is explored.Therefore,strain regularity on the cross-section of 50 mm thickness elm(Ulmus rubra)board at the temperature of 40℃and 80℃is detected via digital image correlation technology.Hence,the difference between tangential and radial strain at surface and core layers was denoted.The results showed that strain distribution in the width direction of the board is uneven.Moreover,a large drying shrinkage strain occurs at the near-core layer,while the maximum strain difference reaches 4.08%.Hence,the surface of the board is cracked along the thickness direction.The radial strain of the board is higher than the tangential strain in the early stage of drying,while these strains are reversed in the later stage of drying.The temperature is related to the difference between the tangential and radial strains of the elm board.These differences at the core layer are larger than those of the surface layer.The conducted research results provide a theoretical basis for process optimization.
基金Science and Technology Research and Development Project of Chengde City,Hebei Province(201706A043)Young Scholar Program of Hebei Pharmaceutical Association Hospital Pharmaceutical Research Project(2020—Hbsyxhqn0029)Public Health Service Subsidy Fund Project of Chinese Medicine Department,State Administration of Traditional Chinese Medicine(Guo Zhong Yi Gui Cai Fa[2015]No.21).
文摘[Objectives]To explore the correlation of processing technology,physical parameters and chemical components during plain stir-baking of Trichosanthis Radix.[Methods]Based on mixture uniform experiment design,the Trichosanthis Radix was prepared by plain stir-bake method.Delphi method was used to evaluate and select the highest-scoring processed product for measuring physical parameters.UV spectrophotometry was used to determine the contents of starch and polysaccharide.The correlation and linear regression model of processing technology,physical parameters and chemical components were established with the aid of SPSS 26.0[Results]After processing by plain stir-bake method,the relative density and chromaticity showed a decreasing trend in the processed products of Trichosanthis Radix,the oxidation value,hydroscopic rate and swelling decreased firstly and then increased,and pH increased firstly and then decreased.The content of total starch decreased,the content of polysaccharide increased,and there was a negative correlation between them.There was a significant positive correlation between temperature and oxidation value,swelling and hydroscopic rate,hydroscopic rate and polysaccharide,and there was a significant negative correlation between relative density and hydroscopic rate or polysaccharide,total starch and hydroscopic rate or swelling.The linear relation model between processing technology and physical parameters and chemical components was r2>0.9.[Conclusions]After processing by plain stir-bake method,the physical parameters of Trichosanthis Radix changed,and there may be mutual conversion between total starch and polysaccharides.To a certain extent,physical parameters can be used to evaluate the quality of processed products of Trichosanthis Radix.This study is expected to provide a reference for research on quality evaluation of processed products of traditional Chinese medicine.
文摘Signals from infrared detector are very weak in SO2 concentration measuring system.In order to improve the sensitivity of detection,combining with filter correlation technology and infrared absorption principle,the weak signal processing circuit is designed according to correlation detection technology.Under laboratory conditions,system performance of SO2 concentration is tested,and the experimental data are analyzed and processed.Then relationship of SO2 concentration and the measuring voltage is provided to prove that the design improves measuring sensitivity of the system.
