To handle input and output time delays that commonly exist in many networked control systems(NCSs), a new robust continuous sliding mode control(CSMC) scheme is proposed for the output tracking in uncertain single inp...To handle input and output time delays that commonly exist in many networked control systems(NCSs), a new robust continuous sliding mode control(CSMC) scheme is proposed for the output tracking in uncertain single input-single-output(SISO) networked control systems. This scheme consists of three consecutive steps. First, although the network-induced delay in those systems can be effectively handled by using Pade approximation(PA), the unmatched disturbance cames out as another difficulty in the control design. Second, to actively estimate this unmatched disturbance, a generalized proportional integral observer(GPIO) technique is utilized based on only one measured state. Third, by constructing a new sliding manifold with the aid of the estimated unmatched disturbance and states, a GPIO-based CSMC is synthesized, which is employed to cope with not only matched and unmatched disturbances, but also networkinduced delays. The stability of the entire closed-loop system under the proposed GPIO-based CSMC is detailedly analyzed.The promising tracking efficiency and feasibility of the proposed control methodology are verified through simulations and experiments on Quanser's servo module for motion control under various test conditions.展开更多
The degradation of formaldehyde gas was studied using UV/TiO2/O3 process under the condition of continuous flow mode. The effects of humidity, initial formaldehyde concentration, residence time and ozone adding amount...The degradation of formaldehyde gas was studied using UV/TiO2/O3 process under the condition of continuous flow mode. The effects of humidity, initial formaldehyde concentration, residence time and ozone adding amount on degradation of formaldehyde gas were investigated. The experimental results indicated that the combination of ozonation with photocatalytic oxidation on the degradation of formaldehyde showed a synergetic action, e.g,, it could considerably increase decomposing of formaldehyde. The degradation efficiency of formaldehyde was between 73.6% and 79.4% while the initial concentration in the range of 1.84--24 mg/m^3 by O3/TiO2flJV process. The optimal humidity was about 50% in UV/TiO2/O3 processs and degradation of formaldehyde increases from 39.0% to 94.1% when the ozone content increased from 0 to 141 mg/m^3. Furthermore, the kinetics of formaldehyde degradation reaction could be described by Langmuir-Hinshelwood model. The rate constant k of 46.72 mg/（m^3.min） and Langmuir adsorption coefficient K of 0.0268 m^3/mg were obtained.展开更多
Lubrication and friction between the mould and strand are strongly influenced by mould oscillation, and play an important role in slab quality and operating safety during continuous casting processes. Investigation of...Lubrication and friction between the mould and strand are strongly influenced by mould oscillation, and play an important role in slab quality and operating safety during continuous casting processes. Investigation of mould oscillation is therefore essential for getting a better online control of the mould processes. A feasible approach for the development and optimization of mould oscillation was put forward, which combined online measurement of mould friction, design of negative oscillating parameters and evaluation for powder consumption. Three different control models including sinusoidal and non-sinusoidal oscillation for mould oscillations were developed to investigate and evaluate the effects of oscillation on mould friction and powder lubrication. For the purpose of investigating mould friction between mould and strand, online measurement was carried out on a slab continuous caster equipped with a hydraulic oscillator. Also the comparison of the mould friction in sinusoidal and non-sinusoidal mould oscillation was made for subsequent analysis. The industrial experiment result shows that the combination of inverse control model and non-sinusoidal oscillation mode will contribute to the proper powder consumption, leading to a suitable effect of friction force on strand surface, especially for high speed continuous casting. The proposed method provides reliable basis for guiding and optimizing mould oscillation among control models, sinusoidal oscillation and non-sinusoidal oscillation.展开更多
According to the fact that the actual inductor and actual capacitor are fractional, the mathematical and state-space averaging models of fractional order Buck converters in continuous conduction mode(CCM) are construc...According to the fact that the actual inductor and actual capacitor are fractional, the mathematical and state-space averaging models of fractional order Buck converters in continuous conduction mode(CCM) are constructed by using fractional calculus theory. Firstly, the parameter conditions that ensure that the converter working in CCM is given and transfer functions are derived. Also, the inductor current and the output voltage are analyzed. Then the difference between the mathematical model and the circuit model are analyzed, and the effect of fractional order is studied by comparing the integer order with fractional order model. Finally, the dynamic behavior of the current-controlled Buck converter is investigated. Simulation experiments are achieved via the use of Matlab/Simulink. The experimental results verify the correctness of theoretical analysis, the order should be taken as a significant parameter. When the order is taken as a bifurcation parameter, the dynamic behavior of the converter will be affected and bifurcation points will be changed as order varies.展开更多
We used a ultrasound/Fe2＋/H2O2 process in continuous dosing mode to degrade the alachlor. Experimental results indicated that lower pH levels enhanced the degradation and mineralization of alachlor. The maximum alach...We used a ultrasound/Fe2＋/H2O2 process in continuous dosing mode to degrade the alachlor. Experimental results indicated that lower pH levels enhanced the degradation and mineralization of alachlor. The maximum alachlor degradation （initial alachlor concentration of 50 mg/L） was as high as 100% at pH 3 with ultrasound of 100 Watts, 20 mg/L of Fe2＋, 2 mg/min of H2O2 and 20℃ within 60 min reaction combined with 46.8% total organic carbon removal. Higher reaction temperatures inhibited the degradation of alachlor. Adequate dosages of Fe2＋ and H2O2 in ultrasound/Fe2＋/H2O2 process not only enhance the degradation efficiency of alachlor but also save the operational cost than the sole ultrasound or Fenton process. A continuous dosing mode ultrasound/Fe2＋/H2O2 process was proven as an effective method to degrade the alachlor.展开更多
This study proposes and experimentally validates an optimal integrated system to control the automotive continuously variable transmission(CVT)by Model Predictive Control(MPC)to achieve its expected transmission effic...This study proposes and experimentally validates an optimal integrated system to control the automotive continuously variable transmission(CVT)by Model Predictive Control(MPC)to achieve its expected transmission efficiency range.The control system framework consists of top and bottom layers.In the top layer,a driving intention recognition system is designed on the basis of fuzzy control strategy to determine the relationship between the driver intention and CVT target ratio at the corresponding time.In the bottom layer,a new slip state dynamic equation is obtained considering slip characteristics and its related constraints,and a clamping force bench is established.Innovatively,a joint controller based on model predictive control(MPC)is designed taking internal combustion engine torque and slip between the metal belt and pulley as optimization dual targets.A cycle is attained by solving the optimization target to achieve optimum engine torque and the input slip in real-time.Moreover,the new controller provides good robustness.Finally,performance is tested by actual CVT vehicles.Results show that compared with traditional control,the proposed control improves vehicle transmission efficiency by approximately 9.12%-9.35%with high accuracy.展开更多
Atmospheric disturbances at 300 hPa are decomposed into normal modes, referred as discrete—spectrum disturbances which can propagate freely in the observed zonal mean flow, and non—modal transient disturbances, refe...Atmospheric disturbances at 300 hPa are decomposed into normal modes, referred as discrete—spectrum disturbances which can propagate freely in the observed zonal mean flow, and non—modal transient disturbances, referred as continuous—spectrum disturbances which are continuously sheared and eventually absorbed by the zonal flow. It is shown that normal modes represent only a small fraction of the observed atmospheric disturbances, while continuous—spectrum disturbances represent the majority of observed disturbances, even when the basic flow is unstable. Daily variabilities of the observed continuous—spectrum disturbances are presented. They are shown to follow the results of wave—packet theory. Calculations suggest that there are abundant sources to excite continuous—spectrum disturbances in the atmosphere.展开更多
Elastic critical buckling load of a column depends on various parameters,such as boundary conditions,material,and crosssection geometry.The main purpose of this work is to present a new method for investigating the bu...Elastic critical buckling load of a column depends on various parameters,such as boundary conditions,material,and crosssection geometry.The main purpose of this work is to present a new method for investigating the buckling load of tapered columns subjected to axial force.The proposed method is based on modified buckling mode shape of tapered structure and perturbation theory.The mode shape of the damaged structure can be expressed as a linear combination of mode shapes of the intact structure.Variations in length in piecewise form can be positive or negative.The method can be used for single-span and continuous columns.Comparison of results with those of finite element and Timoshenko methods shows the high accuracy and efficiency of the proposed method for detecting buckling load.展开更多
A continuous-wave Nd:KGd(WO4)2 single-longitudinal-mode laser is demonstrated with Fabry-Perot etalons in a simple linear cavity.The thermal lens effect is dramatically lowered by propagating the laser beam along the...A continuous-wave Nd:KGd(WO4)2 single-longitudinal-mode laser is demonstrated with Fabry-Perot etalons in a simple linear cavity.The thermal lens effect is dramatically lowered by propagating the laser beam along the‘athermal’direction inside the laser crystal,which is very beneficial to removing the heat generated in the mode selection process.The maximum single-longitudinal-mode output power obtained is 64.8 mW at incident pump power of 4.7 W,corresponding to an optical conversion efficiency of 1.3%and a slope efficiency of 1.7%.展开更多
Based on the method of strain mode, damage identification of continuous beam bridges by comparing the variance of several curves of strain modes difference is studied. Three cases of numerical simulation demonstrate t...Based on the method of strain mode, damage identification of continuous beam bridges by comparing the variance of several curves of strain modes difference is studied. Three cases of numerical simulation demonstrate that the proposed method is applicable to detecting many a damage in a continuous beam bridge, which accurately identifies the damaged positions of the bridge, and detects the damage severity of an element by its according peak value of the curve of strain modes difference that is found to increase with the increasing damage severity.展开更多
The difficulty of quantum key agreement is to realize its security and fairness at the same time.This paper presents a new three-party quantum key agreement protocol based on continuous variable single-mode squeezed s...The difficulty of quantum key agreement is to realize its security and fairness at the same time.This paper presents a new three-party quantum key agreement protocol based on continuous variable single-mode squeezed state.The three parties participating in the agreement are peer entities,making same contributions to the final key.Any one or two participants of the agreement cannot determine the shared key separately.The security analysis shows that the proposed protocol can resist both external and internal attacks.展开更多
Frequency-Modulation Continuous-Wave Synthetic Aperture Radar(FMCW SAR)has shown great potential in the applications of civil and military fields because of its easy deployment and low cost.However,most of these work ...Frequency-Modulation Continuous-Wave Synthetic Aperture Radar(FMCW SAR)has shown great potential in the applications of civil and military fields because of its easy deployment and low cost.However,most of these work and analysis are concentrated on airborne FMCW SAR,where the characteristics of the imaging geometry and signal are much similar to that of traditional pulsed-SAR.As a result,a series of test campaigns of automobile-based FMCW SAR were sponsored by Institute of Electronics,Chinese Academy of Sciences(IECAS)in the autumn of 2012.In this paper,we analyze the imaging issues of FMCW SAR in automobile mode(named as near range mode),where a vehicle is used as moving platform and a large looking angle is configured.The imaging geometry and signal properties are analyzed in detail.We emphasize the difference of the near range mode from the traditional airborne SAR mode.Based on the analysis,a focusing approach is proposed in the paper to handle the data focusing in the case.Simulation experiment and real data of automobile FMCW SAR are used to validate the analysis.展开更多
An example is presented to introduce the concept of implicit continuity proposed as contrasted with the explicit continuity.A sufficient and necessary condition of the implicit continuity is given and proved in forms ...An example is presented to introduce the concept of implicit continuity proposed as contrasted with the explicit continuity.A sufficient and necessary condition of the implicit continuity is given and proved in forms of implicit system.This condition also offers the solution of initial values at the points where the dynamic system is discontinuous.Some discussions are contributed to the physical significance of implicit continuity.展开更多
A 1∶2.5 scale tundish model was set up in laboratory for a six-strand billet continuous casting tundish with different configurations to investigate fluid flow characteristics under different operational conditions b...A 1∶2.5 scale tundish model was set up in laboratory for a six-strand billet continuous casting tundish with different configurations to investigate fluid flow characteristics under different operational conditions by measuring residence time distribution curves.It was found that minimum residence time,maximum concentration time and average residence time of the three strands on the same side of the tundish with the former configuration under normal operation,that is,six strands were open,were small and non-uniform and the tundish had large dead volume fraction.Vortexes easily formed on the liquid surface in the pouring zone of the tundish.The fluid flow characteristics in the tundish with the optimal turbulence inhibitor and baffles were improved and became less non-uniform among the strands.Vortexes were not found on the pouring zone surface in the optimal tundish.For non-normal operation,that is,one strand was close,it was important to choose which strand to be closed for maintaining flow characteristics of the rest two strands.It was found from this investigation that fluid flow characteristics in the optimal configuration tundish with closing strand 2 were better than those with closing strand 3 on the same side.展开更多
This paper discusses a new fibrous composite known as continuous basalt fiber reinforced polymer /plastic(BFRP).Compared with other fiber reinforced polymer/plastic,BFRP has many advantages,such as ductility,high ther...This paper discusses a new fibrous composite known as continuous basalt fiber reinforced polymer /plastic(BFRP).Compared with other fiber reinforced polymer/plastic,BFRP has many advantages,such as ductility,high thermal resistance,corrosion resistance and economic cost.To test mechanical properties and failure modes of flexural members strengthened with BFRP,flexural experiment is conducted on four two-span T-section continuous beams strengthened with BFRP and one un-strengthened comparative beam.The experimental result shows that the strengthened beams perform remarkably in terms of yield strength,ultimate strength and ductility.BFRP has good prospects in retrofitting and strengthening of concrete structures which require good ductility and corrosion resistance.展开更多
The principle and technological design of electroslag continuous casting （ESCC）, including bifilar mode, T-shaped mould, and metal level detecting system, are detailed. Remelting was carded out for 1Crl8Ni9Ti stainl...The principle and technological design of electroslag continuous casting （ESCC）, including bifilar mode, T-shaped mould, and metal level detecting system, are detailed. Remelting was carded out for 1Crl8Ni9Ti stainless steel with ESCC. The surface finish, chemical composition, macroand microstructures, and inclusions of the remelted billets were characterized. ESCC reduces the cost and increases the productivity in comparison to traditional ESR, while achieves comparably excellent products.展开更多
To investigate the impact of combustor width on continuous rotating detonation(CRD)fueled by ethylene and air,a series of 3 D simulations are conducted by changing the inner cylinder radius of an annular combustor whi...To investigate the impact of combustor width on continuous rotating detonation(CRD)fueled by ethylene and air,a series of 3 D simulations are conducted by changing the inner cylinder radius of an annular combustor while retaining the same outer cylinder radius.The results show that the CRD wave propagates more steadily and faster as the combustor width increases.The high-temperature zone at the backward-facing step preheats the propellants and contributes to the steady propagation of the CRD wave in 25-and 30-mm wide combustors.The highest and the lowest velocities are obtained in the30-and 15-mm wide combustors at,respectively,1880.27 and 1681.01 m/s.On the other hand,the average thrust decreases as the combustor width increases.The highest thrust is obtained in the 15-mm wide combustor while the lowest is in the 30-mm wide combustor,at 758.06 and 525.93 N,respectively.Nevertheless,the thrust is much more stable in the 25-and 30-mm wide combustors than in the 15-and 20-mm wide combustors.展开更多
The dynamics of modulated waves in a nonlinear bi-inductance transmission line with dissipative elements are examined.We show the existence of two frequency modes and carry out intensive investigations on the low freq...The dynamics of modulated waves in a nonlinear bi-inductance transmission line with dissipative elements are examined.We show the existence of two frequency modes and carry out intensive investigations on the low frequency mode.Thanks to the multiple scales method,the behavior of these waves is investigated and the dissipative effects are analyzed.It appears that the dissipation coefficient increases with the carrier wave frequency.In the continuous approximation,we derive that the propagation of these waves is governed by the complex Ginzburg-Landau equation instead of the Korteweg-de-Vries equation as previously established.Asymptotic studies of the dynamics of plane waves in the line reveal the existence of three additional regions in the dispersion curve where the modulational phenomenon is observed.In the low frequency mode,we demonstrate that the network allows the propagation of dark and bright solitons.Numerical findings are in perfect agreement with the analytical predictions.展开更多
This paper presents intensive investigation of dynamics of high frequency nonlinear modulated excitations in a damped bimodal lattice. The effects of the dissipation are considered through a linear dissipation coeffic...This paper presents intensive investigation of dynamics of high frequency nonlinear modulated excitations in a damped bimodal lattice. The effects of the dissipation are considered through a linear dissipation coefficient whose evolution in terms of the carrier wave frequency is checked. There appears that the dissipation coefficient increases with the carrier wave frequency. In the linear limit and for high frequency waves, study of the asymptotic behavior of plane waves reveals the existence of two additional regions in the dispersion curve where the modulational phenomenon is observed compared to the lossless line. Based on the multiple scales method exploited in the continuum approximation using an appropriate decoupling ansatz for the voltage of the two different cells, it appears that the motion of modulated waves is described by a dissipative complex Ginzburg–Landau equation instead of a Korteweg–de Vries equation. We also show that this amplitude wave equation admits envelope and hole solitons in the high frequency mode. From basic sources, we design a programmable electronic generator of complex signals with desired characteristics, which delivers signals exploited as input waves for all our numerical simulations. These simulations are performed in the LTspice software that uses realistic components and give the results that corroborate perfectly our analytical predictions.展开更多
The massless scalar quasiaormal modes （QNMs） of a stationary axisymmetric Einstein-Maxwell dilato-axioa （EMDA） black hole are calculated numerically using the continued fraction method first proposed by Leaver. Th...The massless scalar quasiaormal modes （QNMs） of a stationary axisymmetric Einstein-Maxwell dilato-axioa （EMDA） black hole are calculated numerically using the continued fraction method first proposed by Leaver. The fundamental quasinormal frequencies （slowly damped QNMs） are obtained and the peculiar behaviours of them are studied. It is shown that these frequencies depend on the dilaton parameter D, the rotational parameter a, the multiple moment l and the azimuthal number m, and have the same values with other authors at the Schwarzschild and Kerr limit.展开更多
基金supported in part by the Australian Research Council Discovery Project(DP190101557)
文摘To handle input and output time delays that commonly exist in many networked control systems(NCSs), a new robust continuous sliding mode control(CSMC) scheme is proposed for the output tracking in uncertain single input-single-output(SISO) networked control systems. This scheme consists of three consecutive steps. First, although the network-induced delay in those systems can be effectively handled by using Pade approximation(PA), the unmatched disturbance cames out as another difficulty in the control design. Second, to actively estimate this unmatched disturbance, a generalized proportional integral observer(GPIO) technique is utilized based on only one measured state. Third, by constructing a new sliding manifold with the aid of the estimated unmatched disturbance and states, a GPIO-based CSMC is synthesized, which is employed to cope with not only matched and unmatched disturbances, but also networkinduced delays. The stability of the entire closed-loop system under the proposed GPIO-based CSMC is detailedly analyzed.The promising tracking efficiency and feasibility of the proposed control methodology are verified through simulations and experiments on Quanser's servo module for motion control under various test conditions.
基金Project supported by the Science Project of Harbin City(No. H2001-12)the Youth Foundation of School of Municipal and Environmental Engineering in Harbin Institute of Technology(No. 01306914).
文摘The degradation of formaldehyde gas was studied using UV/TiO2/O3 process under the condition of continuous flow mode. The effects of humidity, initial formaldehyde concentration, residence time and ozone adding amount on degradation of formaldehyde gas were investigated. The experimental results indicated that the combination of ozonation with photocatalytic oxidation on the degradation of formaldehyde showed a synergetic action, e.g,, it could considerably increase decomposing of formaldehyde. The degradation efficiency of formaldehyde was between 73.6% and 79.4% while the initial concentration in the range of 1.84--24 mg/m^3 by O3/TiO2flJV process. The optimal humidity was about 50% in UV/TiO2/O3 processs and degradation of formaldehyde increases from 39.0% to 94.1% when the ozone content increased from 0 to 141 mg/m^3. Furthermore, the kinetics of formaldehyde degradation reaction could be described by Langmuir-Hinshelwood model. The rate constant k of 46.72 mg/（m^3.min） and Langmuir adsorption coefficient K of 0.0268 m^3/mg were obtained.
基金Item Sponsored by National Natural Science Foundation of China(51004012)National High-Tech Research and Development Program (863 Program) of China (2009AA04Z134)China Postdoctoral Science Foundation (2012M520621)
文摘Lubrication and friction between the mould and strand are strongly influenced by mould oscillation, and play an important role in slab quality and operating safety during continuous casting processes. Investigation of mould oscillation is therefore essential for getting a better online control of the mould processes. A feasible approach for the development and optimization of mould oscillation was put forward, which combined online measurement of mould friction, design of negative oscillating parameters and evaluation for powder consumption. Three different control models including sinusoidal and non-sinusoidal oscillation for mould oscillations were developed to investigate and evaluate the effects of oscillation on mould friction and powder lubrication. For the purpose of investigating mould friction between mould and strand, online measurement was carried out on a slab continuous caster equipped with a hydraulic oscillator. Also the comparison of the mould friction in sinusoidal and non-sinusoidal mould oscillation was made for subsequent analysis. The industrial experiment result shows that the combination of inverse control model and non-sinusoidal oscillation mode will contribute to the proper powder consumption, leading to a suitable effect of friction force on strand surface, especially for high speed continuous casting. The proposed method provides reliable basis for guiding and optimizing mould oscillation among control models, sinusoidal oscillation and non-sinusoidal oscillation.
基金Sponsored by the National Natural Sciences Foundation of China(Grant No.61201227)
文摘According to the fact that the actual inductor and actual capacitor are fractional, the mathematical and state-space averaging models of fractional order Buck converters in continuous conduction mode(CCM) are constructed by using fractional calculus theory. Firstly, the parameter conditions that ensure that the converter working in CCM is given and transfer functions are derived. Also, the inductor current and the output voltage are analyzed. Then the difference between the mathematical model and the circuit model are analyzed, and the effect of fractional order is studied by comparing the integer order with fractional order model. Finally, the dynamic behavior of the current-controlled Buck converter is investigated. Simulation experiments are achieved via the use of Matlab/Simulink. The experimental results verify the correctness of theoretical analysis, the order should be taken as a significant parameter. When the order is taken as a bifurcation parameter, the dynamic behavior of the converter will be affected and bifurcation points will be changed as order varies.
基金supported by the National Science Council, Republic of China (No. 101-2221-E-264-005)
文摘We used a ultrasound/Fe2＋/H2O2 process in continuous dosing mode to degrade the alachlor. Experimental results indicated that lower pH levels enhanced the degradation and mineralization of alachlor. The maximum alachlor degradation （initial alachlor concentration of 50 mg/L） was as high as 100% at pH 3 with ultrasound of 100 Watts, 20 mg/L of Fe2＋, 2 mg/min of H2O2 and 20℃ within 60 min reaction combined with 46.8% total organic carbon removal. Higher reaction temperatures inhibited the degradation of alachlor. Adequate dosages of Fe2＋ and H2O2 in ultrasound/Fe2＋/H2O2 process not only enhance the degradation efficiency of alachlor but also save the operational cost than the sole ultrasound or Fenton process. A continuous dosing mode ultrasound/Fe2＋/H2O2 process was proven as an effective method to degrade the alachlor.
基金Supported by National Natural Science Foundation of China(Grant No.51905044)Postdoctoral Science Foundation of China(Grant No.2017M611316).
文摘This study proposes and experimentally validates an optimal integrated system to control the automotive continuously variable transmission(CVT)by Model Predictive Control(MPC)to achieve its expected transmission efficiency range.The control system framework consists of top and bottom layers.In the top layer,a driving intention recognition system is designed on the basis of fuzzy control strategy to determine the relationship between the driver intention and CVT target ratio at the corresponding time.In the bottom layer,a new slip state dynamic equation is obtained considering slip characteristics and its related constraints,and a clamping force bench is established.Innovatively,a joint controller based on model predictive control(MPC)is designed taking internal combustion engine torque and slip between the metal belt and pulley as optimization dual targets.A cycle is attained by solving the optimization target to achieve optimum engine torque and the input slip in real-time.Moreover,the new controller provides good robustness.Finally,performance is tested by actual CVT vehicles.Results show that compared with traditional control,the proposed control improves vehicle transmission efficiency by approximately 9.12%-9.35%with high accuracy.
文摘Atmospheric disturbances at 300 hPa are decomposed into normal modes, referred as discrete—spectrum disturbances which can propagate freely in the observed zonal mean flow, and non—modal transient disturbances, referred as continuous—spectrum disturbances which are continuously sheared and eventually absorbed by the zonal flow. It is shown that normal modes represent only a small fraction of the observed atmospheric disturbances, while continuous—spectrum disturbances represent the majority of observed disturbances, even when the basic flow is unstable. Daily variabilities of the observed continuous—spectrum disturbances are presented. They are shown to follow the results of wave—packet theory. Calculations suggest that there are abundant sources to excite continuous—spectrum disturbances in the atmosphere.
文摘Elastic critical buckling load of a column depends on various parameters,such as boundary conditions,material,and crosssection geometry.The main purpose of this work is to present a new method for investigating the buckling load of tapered columns subjected to axial force.The proposed method is based on modified buckling mode shape of tapered structure and perturbation theory.The mode shape of the damaged structure can be expressed as a linear combination of mode shapes of the intact structure.Variations in length in piecewise form can be positive or negative.The method can be used for single-span and continuous columns.Comparison of results with those of finite element and Timoshenko methods shows the high accuracy and efficiency of the proposed method for detecting buckling load.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11674273 and 61805209).
文摘A continuous-wave Nd:KGd(WO4)2 single-longitudinal-mode laser is demonstrated with Fabry-Perot etalons in a simple linear cavity.The thermal lens effect is dramatically lowered by propagating the laser beam along the‘athermal’direction inside the laser crystal,which is very beneficial to removing the heat generated in the mode selection process.The maximum single-longitudinal-mode output power obtained is 64.8 mW at incident pump power of 4.7 W,corresponding to an optical conversion efficiency of 1.3%and a slope efficiency of 1.7%.
文摘Based on the method of strain mode, damage identification of continuous beam bridges by comparing the variance of several curves of strain modes difference is studied. Three cases of numerical simulation demonstrate that the proposed method is applicable to detecting many a damage in a continuous beam bridge, which accurately identifies the damaged positions of the bridge, and detects the damage severity of an element by its according peak value of the curve of strain modes difference that is found to increase with the increasing damage severity.
基金Supported by Beijing Natural Science Foundation under Grant Nos.4182006,4162005National Natural Science Foundation of China under Grant Nos.61572053,61472048,61671087,U1636106,61602019,61502016
文摘The difficulty of quantum key agreement is to realize its security and fairness at the same time.This paper presents a new three-party quantum key agreement protocol based on continuous variable single-mode squeezed state.The three parties participating in the agreement are peer entities,making same contributions to the final key.Any one or two participants of the agreement cannot determine the shared key separately.The security analysis shows that the proposed protocol can resist both external and internal attacks.
文摘Frequency-Modulation Continuous-Wave Synthetic Aperture Radar(FMCW SAR)has shown great potential in the applications of civil and military fields because of its easy deployment and low cost.However,most of these work and analysis are concentrated on airborne FMCW SAR,where the characteristics of the imaging geometry and signal are much similar to that of traditional pulsed-SAR.As a result,a series of test campaigns of automobile-based FMCW SAR were sponsored by Institute of Electronics,Chinese Academy of Sciences(IECAS)in the autumn of 2012.In this paper,we analyze the imaging issues of FMCW SAR in automobile mode(named as near range mode),where a vehicle is used as moving platform and a large looking angle is configured.The imaging geometry and signal properties are analyzed in detail.We emphasize the difference of the near range mode from the traditional airborne SAR mode.Based on the analysis,a focusing approach is proposed in the paper to handle the data focusing in the case.Simulation experiment and real data of automobile FMCW SAR are used to validate the analysis.
文摘An example is presented to introduce the concept of implicit continuity proposed as contrasted with the explicit continuity.A sufficient and necessary condition of the implicit continuity is given and proved in forms of implicit system.This condition also offers the solution of initial values at the points where the dynamic system is discontinuous.Some discussions are contributed to the physical significance of implicit continuity.
基金Item Sponsored by National High Technology Research and Development Plan of China(2007AA04Z194)
文摘A 1∶2.5 scale tundish model was set up in laboratory for a six-strand billet continuous casting tundish with different configurations to investigate fluid flow characteristics under different operational conditions by measuring residence time distribution curves.It was found that minimum residence time,maximum concentration time and average residence time of the three strands on the same side of the tundish with the former configuration under normal operation,that is,six strands were open,were small and non-uniform and the tundish had large dead volume fraction.Vortexes easily formed on the liquid surface in the pouring zone of the tundish.The fluid flow characteristics in the tundish with the optimal turbulence inhibitor and baffles were improved and became less non-uniform among the strands.Vortexes were not found on the pouring zone surface in the optimal tundish.For non-normal operation,that is,one strand was close,it was important to choose which strand to be closed for maintaining flow characteristics of the rest two strands.It was found from this investigation that fluid flow characteristics in the optimal configuration tundish with closing strand 2 were better than those with closing strand 3 on the same side.
基金the National Key Technology Research and Development Program(No.2009BAJ28B02)
文摘This paper discusses a new fibrous composite known as continuous basalt fiber reinforced polymer /plastic(BFRP).Compared with other fiber reinforced polymer/plastic,BFRP has many advantages,such as ductility,high thermal resistance,corrosion resistance and economic cost.To test mechanical properties and failure modes of flexural members strengthened with BFRP,flexural experiment is conducted on four two-span T-section continuous beams strengthened with BFRP and one un-strengthened comparative beam.The experimental result shows that the strengthened beams perform remarkably in terms of yield strength,ultimate strength and ductility.BFRP has good prospects in retrofitting and strengthening of concrete structures which require good ductility and corrosion resistance.
文摘The principle and technological design of electroslag continuous casting （ESCC）, including bifilar mode, T-shaped mould, and metal level detecting system, are detailed. Remelting was carded out for 1Crl8Ni9Ti stainless steel with ESCC. The surface finish, chemical composition, macroand microstructures, and inclusions of the remelted billets were characterized. ESCC reduces the cost and increases the productivity in comparison to traditional ESR, while achieves comparably excellent products.
基金supported by the National Natural Science Foundation of China(No.51776220)the Postgraduate Scientific Research Innovation Project of Hunan Province,China。
文摘To investigate the impact of combustor width on continuous rotating detonation(CRD)fueled by ethylene and air,a series of 3 D simulations are conducted by changing the inner cylinder radius of an annular combustor while retaining the same outer cylinder radius.The results show that the CRD wave propagates more steadily and faster as the combustor width increases.The high-temperature zone at the backward-facing step preheats the propellants and contributes to the steady propagation of the CRD wave in 25-and 30-mm wide combustors.The highest and the lowest velocities are obtained in the30-and 15-mm wide combustors at,respectively,1880.27 and 1681.01 m/s.On the other hand,the average thrust decreases as the combustor width increases.The highest thrust is obtained in the 15-mm wide combustor while the lowest is in the 30-mm wide combustor,at 758.06 and 525.93 N,respectively.Nevertheless,the thrust is much more stable in the 25-and 30-mm wide combustors than in the 15-and 20-mm wide combustors.
文摘The dynamics of modulated waves in a nonlinear bi-inductance transmission line with dissipative elements are examined.We show the existence of two frequency modes and carry out intensive investigations on the low frequency mode.Thanks to the multiple scales method,the behavior of these waves is investigated and the dissipative effects are analyzed.It appears that the dissipation coefficient increases with the carrier wave frequency.In the continuous approximation,we derive that the propagation of these waves is governed by the complex Ginzburg-Landau equation instead of the Korteweg-de-Vries equation as previously established.Asymptotic studies of the dynamics of plane waves in the line reveal the existence of three additional regions in the dispersion curve where the modulational phenomenon is observed.In the low frequency mode,we demonstrate that the network allows the propagation of dark and bright solitons.Numerical findings are in perfect agreement with the analytical predictions.
文摘This paper presents intensive investigation of dynamics of high frequency nonlinear modulated excitations in a damped bimodal lattice. The effects of the dissipation are considered through a linear dissipation coefficient whose evolution in terms of the carrier wave frequency is checked. There appears that the dissipation coefficient increases with the carrier wave frequency. In the linear limit and for high frequency waves, study of the asymptotic behavior of plane waves reveals the existence of two additional regions in the dispersion curve where the modulational phenomenon is observed compared to the lossless line. Based on the multiple scales method exploited in the continuum approximation using an appropriate decoupling ansatz for the voltage of the two different cells, it appears that the motion of modulated waves is described by a dissipative complex Ginzburg–Landau equation instead of a Korteweg–de Vries equation. We also show that this amplitude wave equation admits envelope and hole solitons in the high frequency mode. From basic sources, we design a programmable electronic generator of complex signals with desired characteristics, which delivers signals exploited as input waves for all our numerical simulations. These simulations are performed in the LTspice software that uses realistic components and give the results that corroborate perfectly our analytical predictions.
基金Project supported by the National Natural Science Foundation of China （Grant No 10473004）, the FADEDD （Grant No 200317）, and the SRFDP （Grant No 20040542003）.
文摘The massless scalar quasiaormal modes （QNMs） of a stationary axisymmetric Einstein-Maxwell dilato-axioa （EMDA） black hole are calculated numerically using the continued fraction method first proposed by Leaver. The fundamental quasinormal frequencies （slowly damped QNMs） are obtained and the peculiar behaviours of them are studied. It is shown that these frequencies depend on the dilaton parameter D, the rotational parameter a, the multiple moment l and the azimuthal number m, and have the same values with other authors at the Schwarzschild and Kerr limit.
