To fundamentally alleviate the excavation chamber clogging during slurry tunnel boring machine(TBM)advancing in hard rock,large-diameter short screw conveyor was adopted to slurry TBM of Qingdao Jiaozhou Bay Second Un...To fundamentally alleviate the excavation chamber clogging during slurry tunnel boring machine(TBM)advancing in hard rock,large-diameter short screw conveyor was adopted to slurry TBM of Qingdao Jiaozhou Bay Second Undersea Tunnel.To evaluate the discharging performance of short screw conveyor in different cases,the full-scale transient slurry-rock two-phase model for a short screw conveyor actively discharging rocks was established using computational fluid dynamics-discrete element method(CFD-DEM)coupling approach.In the fluid domain of coupling model,the sliding mesh technology was utilized to describe the rotations of the atmospheric composite cutterhead and the short screw conveyor.In the particle domain of coupling model,the dynamic particle factories were established to produce rock particles with the rotation of the cutterhead.And the accuracy and reliability of the CFD-DEM simulation results were validated via the field test and model test.Furthermore,a comprehensive parameter analysis was conducted to examine the effects of TBM operating parameters,the geometric design of screw conveyor and the size of rocks on the discharging performance of short screw conveyor.Accordingly,a reasonable rotational speed of screw conveyor was suggested and applied to Jiaozhou Bay Second Undersea Tunnel project.The findings in this paper could provide valuable references for addressing the excavation chamber clogging during ultra-large-diameter slurry TBM tunneling in hard rock for similar future.展开更多
Liquid phase exfoliation(LPE)process for graphene production is usually carried out in stirred tank reactor and the interactions between the solvent and the graphite particles are important as to improve the productio...Liquid phase exfoliation(LPE)process for graphene production is usually carried out in stirred tank reactor and the interactions between the solvent and the graphite particles are important as to improve the production efficiency.In this paper,these interactions were revealed by computational fluid dynamics–discrete element method(CFD-DEM)method.Based on simulation results,both liquid phase flow hydrodynamics and particle motion behavior have been analyzed,which gave the general information of the multiphase flow behavior inside the stirred tank reactor as to graphene production.By calculating the threshold at the beginning of graphite exfoliation process,the shear force from the slip velocity was determined as the active force.These results can support the optimization of the graphene production process.展开更多
To study the airflow distribution in human nasal cavity during respiration and the characteristic parameters of nasal structure, three-dimensional, anatomically accurate representations of 30 adult nasal cavity models...To study the airflow distribution in human nasal cavity during respiration and the characteristic parameters of nasal structure, three-dimensional, anatomically accurate representations of 30 adult nasal cavity models were recons- tructed based on processed tomography images collected from normal people. The airflow fields in nasal cavities were simulated by fluid dynamics with finite element software ANSYS. The results showed that the difference of human nasal cavity structure led to different airflow distribution in the nasal cavities and variation of the main airstream passing through the common nasal meatus. The nasal resistance in the regions of nasal valve and nasal vestibule accounted for more than half of the overall resistance. The characteristic model of nasal cavity was extracted on the basis of characteristic points and dimensions deduced from the original models. It showed that either the geometric structure or the airflow field of the two kinds of models was similar. The characteristic dimensions were the characteristic parameters of nasal cavity that could properly represent the original model in model studies on nasal cavity.展开更多
This paper presents an adapted stabilisation method for the equal-order mixed scheme of finite elements on convex polygonal meshes to analyse the high velocity and pressure gradient of incompressible fluid flows that ...This paper presents an adapted stabilisation method for the equal-order mixed scheme of finite elements on convex polygonal meshes to analyse the high velocity and pressure gradient of incompressible fluid flows that are governed by Stokes equations system.This technique is constructed by a local pressure projection which is extremely simple,yet effective,to eliminate the poor or even non-convergence as well as the instability of equal-order mixed polygonal technique.In this research,some numerical examples of incompressible Stokes fluid flow that is coded and programmed by MATLAB will be presented to examine the effectiveness of the proposed stabilised method.展开更多
This paper presents and proves the mixed compatible finite element variationalprinciples in dynamics of viscous barotropic fluids. When the principles are proved, itis found that the compatibility conditions of stress...This paper presents and proves the mixed compatible finite element variationalprinciples in dynamics of viscous barotropic fluids. When the principles are proved, itis found that the compatibility conditions of stress can be naturally satisfied. The gene-rallzed variational principles with mixed hybrid incompatible finite elements are alsopresented and proved, and they can reduce the computation of incompatible elements indynamics of viscous barotropic flows.展开更多
While finite volume methodologies (FVM) have predominated in fluid flow computations, many flow problems, including groundwater models, would benefit from the use of boundary methods, such as the Complex Variable Boun...While finite volume methodologies (FVM) have predominated in fluid flow computations, many flow problems, including groundwater models, would benefit from the use of boundary methods, such as the Complex Variable Boundary Element Method (CVBEM). However, to date, there has been no reporting of a comparison of computational results between the FVM and the CVBEM in the assessment of flow field characteristics. In this work, the CVBEM is used to develop a flow field vector outcome of ideal fluid flow in a 90-degree bend which is then compared to the computational results from a finite volume model of the same situation. The focus of the modelling comparison in the current work is flow field trajectory vectors of the fluid flow, with respect to vector magnitude and direction. Such a comparison is necessary to validate the development of flow field vectors from the CVBEM and is of interest to many engineering flow problems, specifically groundwater modelling. Comparison of the CVBEM and FVM flow field trajectory vectors for the target problem of ideal flow in a 90-degree bend shows good agreement between the considered methodologies.展开更多
A discontinuous Galerkin finite element method （DG-FEM） is developed for solving the axisymmetric Euler equations based on two-dimensional conservation laws. The method is used to simulate the unsteady-state underex...A discontinuous Galerkin finite element method （DG-FEM） is developed for solving the axisymmetric Euler equations based on two-dimensional conservation laws. The method is used to simulate the unsteady-state underexpanded axisymmetric jet. Several flow property distributions along the jet axis, including density, pres- sure and Mach number are obtained and the qualitative flowfield structures of interest are well captured using the proposed method, including shock waves, slipstreams, traveling vortex ring and multiple Mach disks. Two Mach disk locations agree well with computational and experimental measurement results. It indicates that the method is robust and efficient for solving the unsteady-state underexpanded axisymmetric jet.展开更多
This work presents a new application for the Hierarchical Function Expansion Method for the solution of the Navier-Stokes equations for compressible fluids in two dimensions and in high velocity. This method is based ...This work presents a new application for the Hierarchical Function Expansion Method for the solution of the Navier-Stokes equations for compressible fluids in two dimensions and in high velocity. This method is based on the finite elements method using the Petrov-Galerkin formulation, know as SUPG (Streamline Upwind Petrov-Galerkin), applied with the expansion of the variables into hierarchical functions. To test and validate the numerical method proposed as well as the computational program developed simulations are performed for some cases whose theoretical solutions are known. These cases are the following: continuity test, stability and convergence test, temperature step problem, and several oblique shocks. The objective of the last cases is basically to verify the capture of the shock wave by the method developed. The results obtained in the simulations with the proposed method were good both qualitatively and quantitatively when compared with the theoretical solutions. This allows concluding that the objectives of this work are reached.展开更多
A simulation was carried out on an unsteady flow of a viscous, incompressible and electrically conducting fluid past an infinite vertical porous plate. A generic computer program using the Galerkin finite element meth...A simulation was carried out on an unsteady flow of a viscous, incompressible and electrically conducting fluid past an infinite vertical porous plate. A generic computer program using the Galerkin finite element method is employed to solve the coupled non-linear differential equations for velocity and temperature fields. The diffusion equation, the energy equation, the momentum equations and other relevant parameters are transformed into interpretable postfix codes. Numerical calculations are carried out on the flow fields both in the presence of cooling and heating of the plate by free convection currents. The effects of the dimensionless parameters, namely, the Prandtl number, the Eckert number, the modified Grashof number, the Schmidt number and the time on the temperature and velocity distributions are discussed.展开更多
lronmaking using an oxygen blast furnace is an attractive approach for reducing energy consumption in the iron and steel industry. This paper presents a numerical study of gas-solid flow in an oxygen blast fur- nace b...lronmaking using an oxygen blast furnace is an attractive approach for reducing energy consumption in the iron and steel industry. This paper presents a numerical study of gas-solid flow in an oxygen blast fur- nace by coupling the discrete element method with computational fluid dynamics. The model reliability was verified by previous experimental results. The influences of particle diameter, shaft tuyere size, and specific ratio （X） of shaft-injected gas （51G） flowrate to total gas flowrate on the SIC penetration behavior and pressure field in the furnace were investigated. The results showed that gas penetration capacity in the furnace gradually decreased as the particle diameter decreased from 100 to 40 mm. Decreasing particle diameter and increasing shaft tuyere size both slightly increased the SIG concentration near the furnace wall but decreased it at the furnace center. The value of X has a significant impact on the SIG distribution. According to the pressure fields obtained under different conditions, the key factor affecting SIG penetration depth is the pressure difference between the upper and lower levels of the shaft tuyere. If the pressure difference is small, the SIG can easily penetrate to the furnace center.展开更多
The pebble-bed reactor is one of the most promising designs for the nuclear energy industry. In this paper,a discrete element method-computational fluid dynamics(DEM-CFD) approach that includes thermal conduction, rad...The pebble-bed reactor is one of the most promising designs for the nuclear energy industry. In this paper,a discrete element method-computational fluid dynamics(DEM-CFD) approach that includes thermal conduction, radiation, and natural convection mechanisms was proposed to simulate the thermal-fluid phenomena after the failure of forced circulation cooling system in a pebble-bed core. The whole large-scale packed bed was created using the DEM technique, and the calculated radial porosity of the bed was validated with empirical correlations reported by researchers. To reduce computational costs, a segment of the bed was extracted, which served as a good representative of the large-scale packed bed for CFD calculation. The temperature distributions simulated with two different fluids in this DEM-CFD approach were in good agreement with SANA experimental data. The influence of the natural convection mechanism on heat transfer must be taken into account for coolants with strong convective capacity. The proposed DEM-CFD methodology offers a computationally efficient and widely applied method for understanding the heat transfer process in a pebble-bed core. The method can also be easily extended to assess the passive safety features of newly designed fluoride-salt-cooled pebble-bed reactors.展开更多
Research on recycling waste Printed Circuit Boards(PCB) is at the forefront of preventing environmental pollution and finding ways to recycle resources.The Tapered Column Separation Bed(TCSB) is invented aiming at dis...Research on recycling waste Printed Circuit Boards(PCB) is at the forefront of preventing environmental pollution and finding ways to recycle resources.The Tapered Column Separation Bed(TCSB) is invented aiming at disposing the problem that fine particles of waste printed circuit boards cannot be separated efficiently so as to obtain further insight about the underlying mechanisms and demonstrate the separation feasibility in the tapered column separation bed.In this work,a Computational Fluid Dynamics(CFD) coupled with Discrete Element Method(DEM) model for two-phase flow has been extended to simulate the fluid-solid flow in the tapered column separation bed.Its validity is demonstrated by its successful capturing the key features of particles' flow pattern,velocity,the pressure distribution,the axial position with time and axial force for particles with different densities.Simulation results show that the plastic particles and resin particles become overflow,while copper particles,iron particles and aluminum particles successively become underflow,with a discharge water flow rate of 1 m^3/h,an obliquity of 30°.The simulated results agree reasonably well with the experimental observation.Using this equipment to separate waste PCBs is feasible,theoretically.展开更多
The agglomeration behavior of particles significantly impacts on the defluidization occurring in a fluidized bed during the direct reduction process.The influence of CO/H_(2)ratio on surface diffusion of iron atoms wa...The agglomeration behavior of particles significantly impacts on the defluidization occurring in a fluidized bed during the direct reduction process.The influence of CO/H_(2)ratio on surface diffusion of iron atoms was proposed,and the solid bridge force between iron oxide particles was quantificationally analyzed.Moreover,the solid bridge force was successfully added into a CFD–DEM(computational fluid dynamics–discrete element method)model combined with heat transfer and mass transport to investigate the detailed information of agglomeration in a fluidized bed,including the spatial distribution of temperature,velocity and metallization of iron oxide particles.The region of defluidization is sensitive to the reduction temperature.At the same reduction temperature,the iron oxide powder will perform higher metallization and stable fluidization properties with molar fraction of H_(2)in the range of 0.6–0.8,when iron oxide is reduced by CO/H_(2)mixture.展开更多
【目的】棒销式砂磨机的工作过程存在复杂的气体、液体和固体的三相耦合现象,为了使仿真工况更接近实际工况,构建气-液-固三相耦合仿真模型,提高棒销式砂磨机仿真设计的准确性。【方法】采用离散单元法(discrete element method,DEM)和...【目的】棒销式砂磨机的工作过程存在复杂的气体、液体和固体的三相耦合现象,为了使仿真工况更接近实际工况,构建气-液-固三相耦合仿真模型,提高棒销式砂磨机仿真设计的准确性。【方法】采用离散单元法(discrete element method,DEM)和计算流体动力学(computational fluid dynamics,CFD)分别研究固体相和流体相,并引入流体体积模型(volume of fluid model,VOF)区分流体相所包含的液体相和气体相,分析固体相运动方程、流体相控制方程,确定气-液界面的识别方法和耦合计算方法,制定仿真流程;通过单球落水仿真、颗粒群落水仿真试验分析CFD-DEM-VOF三相耦合模型仿真计算的精度,并进行准确性验证;在设置仿真参数、进行网格划分及其无关性分析基础上,针对棒销式砂磨机的CFD-DEM-VOF三相耦合模型进行仿真试验;对流体速度、颗粒总能量和颗粒的速度的仿真结果进行分析,并通过实验验证仿真结果。【结果】在单球落水仿真试验中,根据CFD-DEM-VOF三相耦合模型的仿真结果与根据Stokes定律的理论计算结果基本吻合;在颗粒群落水仿真过程中,液面上升高度的仿真值与理论值之间的相对误差为1.37%,VOF模型的体积守恒性较好;棒销四面体网格边长小于2 mm、研磨桶四面体网格边长小于2.5 mm时,满足网格独立性的精度要求,同时计算量也较少;随着棒销转速的增大,流体速度、颗粒总能量、颗粒平均速度也逐渐增大;当棒销转速为1400~2000 r/min时,CFD-DEM-VOF三相耦合模型流体速度的仿真与实验结果最为接近;当棒销转速为1400~2200 r/min时,CFD-DEM-VOF三相耦合模型的颗粒总能量仿真值与实验值的最大相对误差为1%。【结论】与仅仅采用流体相、固体相单相模型或固-液两相模型相比,采用CFD-DEM-VOF三相耦合模型设计棒销式砂磨机的计算精度和准确性较高,仿真性能好。展开更多
基金supported by the Fundamental Research Funds for the Central Universities(Grant No.2023YJS053)the National Natural Science Foundation of China(Grant No.52278386).
文摘To fundamentally alleviate the excavation chamber clogging during slurry tunnel boring machine(TBM)advancing in hard rock,large-diameter short screw conveyor was adopted to slurry TBM of Qingdao Jiaozhou Bay Second Undersea Tunnel.To evaluate the discharging performance of short screw conveyor in different cases,the full-scale transient slurry-rock two-phase model for a short screw conveyor actively discharging rocks was established using computational fluid dynamics-discrete element method(CFD-DEM)coupling approach.In the fluid domain of coupling model,the sliding mesh technology was utilized to describe the rotations of the atmospheric composite cutterhead and the short screw conveyor.In the particle domain of coupling model,the dynamic particle factories were established to produce rock particles with the rotation of the cutterhead.And the accuracy and reliability of the CFD-DEM simulation results were validated via the field test and model test.Furthermore,a comprehensive parameter analysis was conducted to examine the effects of TBM operating parameters,the geometric design of screw conveyor and the size of rocks on the discharging performance of short screw conveyor.Accordingly,a reasonable rotational speed of screw conveyor was suggested and applied to Jiaozhou Bay Second Undersea Tunnel project.The findings in this paper could provide valuable references for addressing the excavation chamber clogging during ultra-large-diameter slurry TBM tunneling in hard rock for similar future.
基金National Natural Science Foundation of China(U2004176,22008055)Technology Research Project of Henan Province(232102240034)are gratefully acknowledged.
文摘Liquid phase exfoliation(LPE)process for graphene production is usually carried out in stirred tank reactor and the interactions between the solvent and the graphite particles are important as to improve the production efficiency.In this paper,these interactions were revealed by computational fluid dynamics–discrete element method(CFD-DEM)method.Based on simulation results,both liquid phase flow hydrodynamics and particle motion behavior have been analyzed,which gave the general information of the multiphase flow behavior inside the stirred tank reactor as to graphene production.By calculating the threshold at the beginning of graphite exfoliation process,the shear force from the slip velocity was determined as the active force.These results can support the optimization of the graphene production process.
基金the National Natural Science Foundation of China (1047202510672036)the Natural Science Foundation of Liaoning Province,China (20032109)
文摘To study the airflow distribution in human nasal cavity during respiration and the characteristic parameters of nasal structure, three-dimensional, anatomically accurate representations of 30 adult nasal cavity models were recons- tructed based on processed tomography images collected from normal people. The airflow fields in nasal cavities were simulated by fluid dynamics with finite element software ANSYS. The results showed that the difference of human nasal cavity structure led to different airflow distribution in the nasal cavities and variation of the main airstream passing through the common nasal meatus. The nasal resistance in the regions of nasal valve and nasal vestibule accounted for more than half of the overall resistance. The characteristic model of nasal cavity was extracted on the basis of characteristic points and dimensions deduced from the original models. It showed that either the geometric structure or the airflow field of the two kinds of models was similar. The characteristic dimensions were the characteristic parameters of nasal cavity that could properly represent the original model in model studies on nasal cavity.
基金The authors would like to present our gratitude to the Flemish Government financially supporting for the VLIR-OUS TEAM Project,VN2017TEA454A103‘An innovative solution to protect Vietnamese coastal riverbanks from floods and erosion’.
文摘This paper presents an adapted stabilisation method for the equal-order mixed scheme of finite elements on convex polygonal meshes to analyse the high velocity and pressure gradient of incompressible fluid flows that are governed by Stokes equations system.This technique is constructed by a local pressure projection which is extremely simple,yet effective,to eliminate the poor or even non-convergence as well as the instability of equal-order mixed polygonal technique.In this research,some numerical examples of incompressible Stokes fluid flow that is coded and programmed by MATLAB will be presented to examine the effectiveness of the proposed stabilised method.
文摘This paper presents and proves the mixed compatible finite element variationalprinciples in dynamics of viscous barotropic fluids. When the principles are proved, itis found that the compatibility conditions of stress can be naturally satisfied. The gene-rallzed variational principles with mixed hybrid incompatible finite elements are alsopresented and proved, and they can reduce the computation of incompatible elements indynamics of viscous barotropic flows.
文摘While finite volume methodologies (FVM) have predominated in fluid flow computations, many flow problems, including groundwater models, would benefit from the use of boundary methods, such as the Complex Variable Boundary Element Method (CVBEM). However, to date, there has been no reporting of a comparison of computational results between the FVM and the CVBEM in the assessment of flow field characteristics. In this work, the CVBEM is used to develop a flow field vector outcome of ideal fluid flow in a 90-degree bend which is then compared to the computational results from a finite volume model of the same situation. The focus of the modelling comparison in the current work is flow field trajectory vectors of the fluid flow, with respect to vector magnitude and direction. Such a comparison is necessary to validate the development of flow field vectors from the CVBEM and is of interest to many engineering flow problems, specifically groundwater modelling. Comparison of the CVBEM and FVM flow field trajectory vectors for the target problem of ideal flow in a 90-degree bend shows good agreement between the considered methodologies.
文摘A discontinuous Galerkin finite element method （DG-FEM） is developed for solving the axisymmetric Euler equations based on two-dimensional conservation laws. The method is used to simulate the unsteady-state underexpanded axisymmetric jet. Several flow property distributions along the jet axis, including density, pres- sure and Mach number are obtained and the qualitative flowfield structures of interest are well captured using the proposed method, including shock waves, slipstreams, traveling vortex ring and multiple Mach disks. Two Mach disk locations agree well with computational and experimental measurement results. It indicates that the method is robust and efficient for solving the unsteady-state underexpanded axisymmetric jet.
文摘This work presents a new application for the Hierarchical Function Expansion Method for the solution of the Navier-Stokes equations for compressible fluids in two dimensions and in high velocity. This method is based on the finite elements method using the Petrov-Galerkin formulation, know as SUPG (Streamline Upwind Petrov-Galerkin), applied with the expansion of the variables into hierarchical functions. To test and validate the numerical method proposed as well as the computational program developed simulations are performed for some cases whose theoretical solutions are known. These cases are the following: continuity test, stability and convergence test, temperature step problem, and several oblique shocks. The objective of the last cases is basically to verify the capture of the shock wave by the method developed. The results obtained in the simulations with the proposed method were good both qualitatively and quantitatively when compared with the theoretical solutions. This allows concluding that the objectives of this work are reached.
文摘A simulation was carried out on an unsteady flow of a viscous, incompressible and electrically conducting fluid past an infinite vertical porous plate. A generic computer program using the Galerkin finite element method is employed to solve the coupled non-linear differential equations for velocity and temperature fields. The diffusion equation, the energy equation, the momentum equations and other relevant parameters are transformed into interpretable postfix codes. Numerical calculations are carried out on the flow fields both in the presence of cooling and heating of the plate by free convection currents. The effects of the dimensionless parameters, namely, the Prandtl number, the Eckert number, the modified Grashof number, the Schmidt number and the time on the temperature and velocity distributions are discussed.
基金We gratefully acknowledge the support of the National Basic Research Program of China （973 Program） （No. 2012CB720401 ） and the Key Project of National Natural Science Foundation of China （No. 51134008）.
文摘lronmaking using an oxygen blast furnace is an attractive approach for reducing energy consumption in the iron and steel industry. This paper presents a numerical study of gas-solid flow in an oxygen blast fur- nace by coupling the discrete element method with computational fluid dynamics. The model reliability was verified by previous experimental results. The influences of particle diameter, shaft tuyere size, and specific ratio （X） of shaft-injected gas （51G） flowrate to total gas flowrate on the SIC penetration behavior and pressure field in the furnace were investigated. The results showed that gas penetration capacity in the furnace gradually decreased as the particle diameter decreased from 100 to 40 mm. Decreasing particle diameter and increasing shaft tuyere size both slightly increased the SIG concentration near the furnace wall but decreased it at the furnace center. The value of X has a significant impact on the SIG distribution. According to the pressure fields obtained under different conditions, the key factor affecting SIG penetration depth is the pressure difference between the upper and lower levels of the shaft tuyere. If the pressure difference is small, the SIG can easily penetrate to the furnace center.
基金supported by the Chinese TMSR Strategic Pioneer Science and Technology Project(No.XDA02010000)the Frontier Science Key Program of the Chinese Academy of Sciences(No.QYZDY-SSW-JSC016)
文摘The pebble-bed reactor is one of the most promising designs for the nuclear energy industry. In this paper,a discrete element method-computational fluid dynamics(DEM-CFD) approach that includes thermal conduction, radiation, and natural convection mechanisms was proposed to simulate the thermal-fluid phenomena after the failure of forced circulation cooling system in a pebble-bed core. The whole large-scale packed bed was created using the DEM technique, and the calculated radial porosity of the bed was validated with empirical correlations reported by researchers. To reduce computational costs, a segment of the bed was extracted, which served as a good representative of the large-scale packed bed for CFD calculation. The temperature distributions simulated with two different fluids in this DEM-CFD approach were in good agreement with SANA experimental data. The influence of the natural convection mechanism on heat transfer must be taken into account for coolants with strong convective capacity. The proposed DEM-CFD methodology offers a computationally efficient and widely applied method for understanding the heat transfer process in a pebble-bed core. The method can also be easily extended to assess the passive safety features of newly designed fluoride-salt-cooled pebble-bed reactors.
基金the National Key Basic Research Program of China(No.2012CB214904)the National Natural Science Foundation of China for Innovative Research Group(No.51221462)+2 种基金the National Natural Science Foundation of China(Nos.51304196,51134022,and 51174203)the Natural Science Foundation of Jiangsu Province of China(No. BK2012136)the Specialized Research Fund for the Doctoral Program of Higher Education(No.20120095130001)
文摘Research on recycling waste Printed Circuit Boards(PCB) is at the forefront of preventing environmental pollution and finding ways to recycle resources.The Tapered Column Separation Bed(TCSB) is invented aiming at disposing the problem that fine particles of waste printed circuit boards cannot be separated efficiently so as to obtain further insight about the underlying mechanisms and demonstrate the separation feasibility in the tapered column separation bed.In this work,a Computational Fluid Dynamics(CFD) coupled with Discrete Element Method(DEM) model for two-phase flow has been extended to simulate the fluid-solid flow in the tapered column separation bed.Its validity is demonstrated by its successful capturing the key features of particles' flow pattern,velocity,the pressure distribution,the axial position with time and axial force for particles with different densities.Simulation results show that the plastic particles and resin particles become overflow,while copper particles,iron particles and aluminum particles successively become underflow,with a discharge water flow rate of 1 m^3/h,an obliquity of 30°.The simulated results agree reasonably well with the experimental observation.Using this equipment to separate waste PCBs is feasible,theoretically.
基金the National Natural Science Foundation Project of China(51374263 and 51974046).
文摘The agglomeration behavior of particles significantly impacts on the defluidization occurring in a fluidized bed during the direct reduction process.The influence of CO/H_(2)ratio on surface diffusion of iron atoms was proposed,and the solid bridge force between iron oxide particles was quantificationally analyzed.Moreover,the solid bridge force was successfully added into a CFD–DEM(computational fluid dynamics–discrete element method)model combined with heat transfer and mass transport to investigate the detailed information of agglomeration in a fluidized bed,including the spatial distribution of temperature,velocity and metallization of iron oxide particles.The region of defluidization is sensitive to the reduction temperature.At the same reduction temperature,the iron oxide powder will perform higher metallization and stable fluidization properties with molar fraction of H_(2)in the range of 0.6–0.8,when iron oxide is reduced by CO/H_(2)mixture.
