Experimental study on homogeneous charge compression ignition （HCCI） combustion process was carried out on a single-cylinder direct injection diesel engine fueled with dimethyl ether（DME）. The influence of inert g...Experimental study on homogeneous charge compression ignition （HCCI） combustion process was carried out on a single-cylinder direct injection diesel engine fueled with dimethyl ether（DME）. The influence of inert gas CO2 on the ignition and combustion process was investigated. The research results indicate that because of the high cetane number of DME, the stable HCCI operating range is quite narrow while the engine has a high compression ratio. The HCCI operating range can be largely extended when the inert gas is inducted into the charging air. HCCI combustion of DME presents remarkable characteristic of two-stage combustion process. As the concentration of inert gas increases, the ignition timing of the first combustion stage delays, the peak heat release rate decreases, and the combustion duration extends. Inducting inert gas into charging air cannot make the combustion and heat release of DME occur at a perfect crank angle position. Therefore,to obtain HCCI operation for the fuel with high cetane number,other methods such as reducing engine compression ratio should be adopted. Emission results show that under HCCI operation, a nearly zero NOx emission can be obtained with no smoke emissions. But the HC and CO emissions are high, and both rise with the increase of the concentration of inert gases.展开更多
The effects of cooled external exhaust gas recirculation （EGR） on the combustion and emission performance of diesel fuel homogeneous charge compression ignition （HCCI） are studied. Homogeneous mixture is formed by...The effects of cooled external exhaust gas recirculation （EGR） on the combustion and emission performance of diesel fuel homogeneous charge compression ignition （HCCI） are studied. Homogeneous mixture is formed by injecting fuel in-cylinder in the negative valve overlap （NVO） period. So, the HCCI combustion which has low NOx and smoke emission is achieved. Cooled external EGR can delay the start of combustion effectively, which is very useful for high cetane fuel （diesel） HCCI, because these fuels can easily self-ignition, which makes the start of combustion more early. External EGR can avoid the knock combustion of HCCI at high load which means that the EGR can expand the high load limit. HCCI maintains low smoke emission at various EGR rate and various load compared with conventional diesel engine because there is no fuel-rich area in cylinder.展开更多
Gasoline compression ignition(GCI)has been considered as a promising combustion concept to yield ultralow NOX and soot emissions while maintaining high thermal efficiency.However,how to improve the low-load performanc...Gasoline compression ignition(GCI)has been considered as a promising combustion concept to yield ultralow NOX and soot emissions while maintaining high thermal efficiency.However,how to improve the low-load performance becomes an urgent issue to be solved.In this paper,a GCI engine model was built to investigate the effects of internal EGR(i-EGR)and pre-injection on in-cylinder temperature,spatial concentration of mixture and OH radical,combustion and emission characteristics,and the control strategy for improving the combustion performance was further explored.The results showed an obvious expansion of the zone with an equivalence ratio between 0.8∼1.2 is realized by higher pre-injection ratios,and the s decreases with the increase of pre-injection ratio,but increases with the increase of i-EGR ratio.The high overlap among the equivalentmixture zone,the hightemperature zone,and the OH radical-rich zone can be achieved by higher i-EGR ratio coupled with higher preinjection ratio.By increasing the pre-injection ratio,the combustion efficiency increases first and then decreases,also achieves the peak value with a pre-injection ratio of 60%and is unaffected by i-EGR.The emissions of CO,HC,NOX,and soot can also be reduced to low levels by the combination of higher i-EGR ratios and a pre-injection ratio of 60%.展开更多
Gasoline compression ignition(GCI) is a practicable way to obtain low emissions and high thermal efficiency of gasoline-like fuels in internal combustion engines. In this paper, the research octane number(RON) and inj...Gasoline compression ignition(GCI) is a practicable way to obtain low emissions and high thermal efficiency of gasoline-like fuels in internal combustion engines. In this paper, the research octane number(RON) and injection strategy were coordinated to optimize the GCI engine performance and emissions under high loads. The direct injection and port injection were used to achieve two injection strategies: direct injection(DI) and port injection plus direct injection(PIDI), and the primary reference fuels(PRF) with the RON of 60, 70, 80 and 90 were used. The results show that using lower RON fuels under high loads, DI mode can achieve higher efficiency, while PIDI mode can achieve lower combustion noise at an expense of slightly lower fuel economy. When the DI mode is converted to PIDI mode with a pre-injection ratio of 30%, using PRF70 under 12 bar and the exhaust gas recirculation(EGR) rate of 40%, the gross indicated thermal efficiency and the maximum pressure rise rate are reduced by 1% and by 2 bar/°CA, respectively, while the particle emissions also decrease significantly, thus achieving low emissions and high efficiency. However, under the same load and EGR rate, DI mode produces less regulated and unregulated emissions than PIDI mode. In addition, the effect of fuel RON was obvious, the lower RON fuels exhibit obvious three-stage heat release in PIDI mode, however, PRF90 with higher RON only exhibits two-stage heat release, and the peak value of the firststage heat release rate is also lower than those of other fuels.展开更多
The detailed surface reaction mechanism of methane on rhodium catalyst was analyzed. Comparisons between numerical simulation and experiments showed a basic agreement. The combustion process of homogeneous charge comp...The detailed surface reaction mechanism of methane on rhodium catalyst was analyzed. Comparisons between numerical simulation and experiments showed a basic agreement. The combustion process of homogeneous charge compression ignition （HCCI） engine whose piston surface has been coated with catalyst （rhodium and platinum） was numerically investigated. A multi-dimensional model with detailed chemical kinetics was built. The effects of catalytic combustion on the ignition timing, the temperature and CO concentration fields, and HC, CO and NOx emissions of the HCCI engine were discussed. The results showed the ignition timing of the HCCI engine was advanced and the emissions of HC and CO were decreased by the catalysis.展开更多
Sclerocarya birrea(Marula)seed oil was extracted and characterized for its physico-chemical properties and fatty acid compositions,respectively,by using standardized laboratory methods of the Association of Official a...Sclerocarya birrea(Marula)seed oil was extracted and characterized for its physico-chemical properties and fatty acid compositions,respectively,by using standardized laboratory methods of the Association of Official and Analytical Chemist(AOAC).The fuel and lubrication properties of marula oil were also determined by using the ASTM methods,and the oil was evaluated in terms of its antiwear,viscometrics,volatility,stability,environmental compatibility properties and energy content.It was found that the high percentage of mono-unsaturated oleic acid(73.6%)provided the oiliness that makes marula oil a natural alternative to genetically modify high oleic acid sunflower oil used in biodiesel production.The aggregate properties of seed oiliness as exemplified by the high oleic acid content,high saponification value(178.6 mg/KOH)and viscosity(41 mm2/s)makes marula oil to be prospective based oil for engine crank case biolubricants with antiwear and friction reduction properties.However,the higher oil viscosity exhibited by marula seed oil in comparison to diesel could pose some durability problems to compression ignition engines,when used directly as fuel.Nonetheless,the reduction of oil viscosity would be required by heating,blending with diesel fuel,or by transesterification to forestall the risk of engine failure resulting from the use of unmodified marula oil.The flash point of marula oil(235℃)is somewhat close to that of monograde SAE 40 mineral oil(240℃),and appreciably higher than that of diesel fuel(52℃).The high flash point makes the seed oil less flammable and ensures safer handling and transportation.While,the low pour point(-13.7℃)ensures the oil usability for engines at cold start and under low load conditions.The oxidation stability of marula oil is ascribed to the traces of natural antioxidants presented in the oil and improves the oil’s shelf life,notwithstanding the high peroxide value(4.58 mequiv/kg),and linolenic acid content(0.3%),which ought to have been the culprit for lipolytic hydrolysis and rancidity.Furthermore,marula seed oil is more biodegradable and environmentally friendly than oils derived from petroleum crude.The closely related cetane number(47.8)and heating values(38.2 mJ/kg)of marula oil to diesel fuel would undeniably sustain the combustion efficiency of diesel fuel and also supply a comparable engine performance output in compression ignition engines.The candidacy of marula seed oil,as a bioenergy resource for alternative fuel,fuel additives and lubricants,will no doubt expand the energy supply mix,conserve fossil fuel reserves and mitigate environmental contamination.展开更多
The internal combustion engines can remain the advantage over competitor technologies for automotive driven,especially the engine efficiency,exceeded 50%while maintaining ultra-low emissions.In this paper,a novel comb...The internal combustion engines can remain the advantage over competitor technologies for automotive driven,especially the engine efficiency,exceeded 50%while maintaining ultra-low emissions.In this paper,a novel combustion mode characterized by dual high-pressure common-rail direct injection systems,denoted as intelligent charge compression ignition(ICCI)combustion,is proposed to realize high efficiency and clean combustion in wide engine operating ranges.Specifically,commercial gasoline and diesel,which are considered to be complementary in physical and chemical properties,are directly injected into the cylinder by the two independent injection systems,respectively.Through this unique design,the in-cylinder air-fuel mixtures can be flexibly adjusted by regulating injection timing and duration of different fuels,consequently obtaining suitable combustion phase and heat release rate.The ICCI mode can widely run from indicated mean effective pressure 2 bar to 16 bar with an utterly controllable cylinder pressure rising rate,around 50%indicated thermal efficiency and low NOxemissions.A series of experiments were carried out to compare the combustion and emissions of ICCI with other combustion modes(including conventional diesel combustion,reactivity-controlled compression ignition,partially premixed combustion,and gasoline compression ignition).The results show that at the medium engine loads,ICCI mode can reach much high indicated thermal efficiency,especially up to 52%along with extremely low NOxemissions.Prospectively,ICCI mode can realize real-time adjustments of in-cylinder mixture stratification and instantaneous combustion mode switch in one cycle at any operating conditions,and has an excellent commercial application prospect for energy conservation and environmental improvement.展开更多
To meet the requirements of the homogeneous charge compression ignition gasoline engine’s rapid cylinder exhaust gas rate and accurate control of combustion phasing,a residual exhaust gas rate model was proposed.A he...To meet the requirements of the homogeneous charge compression ignition gasoline engine’s rapid cylinder exhaust gas rate and accurate control of combustion phasing,a residual exhaust gas rate model was proposed.A heat dissipation model for gas flow in the exhaust passage and exhaust pipe was established,and the exhaust gas was established.Flow through the exhaust valve was considered as an adiabatic expansion process,the exhaust temperature was used to estimate the temperature in the cylinder at the time that the valve was closed,and the cylinder exhaust gas rate was calculated.To meet the requirements of transient operating conditions,a first-order inertial link was used to correct the thermocouple temperature measurement.Addressing this delay problem and modification of the exhaust wall temperature according to different conditions effectively improved the accuracy of the model.The relative error between the calculated results of this model and the simulation results determined using GT-POWER software was within 3.5%.展开更多
Recently, reactivity controlled compression ignition (RCCI) has been proposed inorder to achieve a higher thermal efficiency with lower emissions than conventional combustion. In RCCI mode, as the fuel types and their...Recently, reactivity controlled compression ignition (RCCI) has been proposed inorder to achieve a higher thermal efficiency with lower emissions than conventional combustion. In RCCI mode, as the fuel types and their combinations affects the reactivity stratificationinside cylinder, thus combustion control, in present study, iso-propanol was evaluated as lowreactivity fuel (LRF) when petroleum diesel, commercial biodiesel and their blends were highreactivity fuels. It is of great importance that iso-propanol and biodiesel be used together inRCCI mode, as they significantly affect the in-cylinder stratification due to their high octane/cetane number. Therefore, the reactivity controlled compression ignition (RCCI) combustioncharacteristics was investigated in a diesel research engine using iso-propanol, petroleumdiesel, biodiesel and their blends as fuels. Tests were conducted on varying loadings (from20% to 60% of max torque) and premixed ratios of LRF (Rp Z 0, 0.15, 0.30, 0.45, and0.60) at a constant engine speed of 2400 rpm. Results, which were compared with conventionaldiesel combustion (CDC), showed that, as the premixed ratio (Rp) of low-reactivity fuel (isopropanol) increased, ignition delay (ID) period prolonged while combustion duration (CD) and rate of pressure rise (RoPR) reduced assisted to reduce NO emissions and smoke opacity in theexhaust. NO and smoke opacity reduced simultaneously for biodiesel-propanol combinationsup to 40% under 20% load and 0.60 premixed ratio of LRF compared to CDC. Propanol premixed ratio of 0.30 at 60% load was found to be optimum concerning lowest emissions. In conventional mode, HC emissions reduced by up to 52% when biodiesel and its blends with dieselfuel are used, whereas they increased significantly in RCCI mode. According to overall results,it is concluded that RCCI performed better than CDC at entire load.展开更多
Ignition timing control is of great importance in homogeneous charge compression ignition engines. The effect of hydrogen addition on methane combustion was investigated using a CHEMKIN multi-zone model. Results show ...Ignition timing control is of great importance in homogeneous charge compression ignition engines. The effect of hydrogen addition on methane combustion was investigated using a CHEMKIN multi-zone model. Results show that hydrogen addition advances ignition tim- ing and enhances peak pressure and temperature. A brief analysis of chemical kinetics of methane blending hydrogen is also performed in order to investigate the scope of its appli- cation, and the analysis suggests that OH radical plays an important role in the oxidation. Hydrogen addition increases NOx while decreasing HC and CO emissions. Exhaust gas recir- culation （EGR） also advances ignition timing; however, its effects on emissions are generally the opposite. By adjusting the hydrogen addition and EGR rate, the ignition timing can be regulated with a low emission level. Investigation into zones suggests that NOx is mostly formed in core zones while HC and CO mostly originate in the crevice and the quench layer.展开更多
The catalytic combustion of methane in a mierochannel whose surface was coated with platinum（Pt） catalyst was studied by numerical-simulation. The effects of gas-phase reactions on the whole catalytic combustion pro...The catalytic combustion of methane in a mierochannel whose surface was coated with platinum（Pt） catalyst was studied by numerical-simulation. The effects of gas-phase reactions on the whole catalytic combustion process were analyzed at a high inlet pressure. A sensitivity analysis of the detailed mechanisms of the surface reaction of methane on Pt revealed that the most sensitive reactions affecting the heterogeneous ignition are oxygen adsorption/desorption and methane adsorption, and the most sensitive reactions affecting the homogeneous ignition are OH and H2O adsorption/desorption. The combustion process of the homogeneous charge compression ignition（HCCI） engine whose piston face was coated with Pt catalyst was simulated. The effects of catalysis and the most sensitive reactions on the ignition timing and the concentration of the main intermediate species during the HCCI engine combustion are discussed. The results show that the ignition timing of the HCCI engine can be increased by catalysis, and the most sensitive reactions affecting the ignition timing of the HCCI engine are OH and H2O adsorption/desorption.展开更多
Near dense Mg 0.5 wt.% Zr（0,1,2.5 and 4） wt.% La alloys were successfully synthesized by disintegrated melt deposition technique followed by hot extrusion and were characterized for their microstructural, ignition, ...Near dense Mg 0.5 wt.% Zr（0,1,2.5 and 4） wt.% La alloys were successfully synthesized by disintegrated melt deposition technique followed by hot extrusion and were characterized for their microstructural, ignition, hardness, tensile and compression properties. Combined effects of Zr and La assisted in significant grain refinement of Mg and Mg 0.5 wt.% Zr 4 wt.% La exhibited an average grain size as low as ~2.75 μm. High ignition temperature of ~645 oC was realized with Mg 0.5 wt.% Zr（1,2.5 and 4） wt.% La alloys. Microhardness value as high as ~103 Hv was observed with Mg 0.5 wt.% Zr 4 wt.% La alloy. Under room temperature tensile and compression loading, significant improvements in the strength properties of pure Mg with the addition of 0.5 wt.% Zr（0, 1, 2.5 and 4） wt.% La was observed. Mg 0.5 wt.% Zr 4 wt.% La exhibited the maximum 0.2% tensile and compression yield strengths of ~283 MPa and ~264 MPa, respectively. The tensile and compression fracture strain values of synthesized pure Mg were found to be unaffected with the addition of 0.5 wt.% Zr. But the tensile fracture strain reduced with the addition of La while the compressive fracture strain was unaffected. Minimal tensile-compression asymmetry（~1） was exhibited by Mg 0.5 wt.% Zr（1 and 2.5） wt.% La alloys.展开更多
This paper examines the effect of equalizing ignition delay in a compression ignition engine.Two sets of tests were conducted,i.e.a set of constant injection timing tests with start of fuel injection at 10°crank ...This paper examines the effect of equalizing ignition delay in a compression ignition engine.Two sets of tests were conducted,i.e.a set of constant injection timing tests with start of fuel injection at 10°crank angle degree(CAD)before top dead center(BTDC)and a set of constant ignition timing tests while also keeping the 10℃AD BTDC injection and adding ignition improver(2-ethylhexylnitrate-,2-EHN)to the fuel mixtures.Soot particles were characterized using DMS-500 instrument in terms of mass,size,and number.The experimental results showed that adding 2-EHN to the model fuel blends reduced the soot surface area,soot mass concentration and soot mean size.Replacing 20 vol%of a C 7-heptane with 20 vol%methyl-decanoate(an oxygenated C 11 molecule)did not affect the ignition delay or rate of fuel air premixing,the peak in-cylinder pressure or heat release rates.Toluene addition(0−22.5 vol%)to heptane increased the mean size of the soot particles generated by only 3%while also resulted in a slight increase in the peak cylinder pressure and peak heat release rates.Blending toluene and methyl-decanoate into heptane without adding 2-EHN increased the premix phase fraction by at least 13%.However,by adding 2-EHN(4×10^(−4)−1.5×10^(−3)),the premixed phase fraction decreased by at least 11%.展开更多
For homogeneous charge compression ignition （HCCI） combustion, the auto-ignition process is very sensitive to in-cylinder conditions, including in-cylinder temperature, in-cylinder components and concentrations. The...For homogeneous charge compression ignition （HCCI） combustion, the auto-ignition process is very sensitive to in-cylinder conditions, including in-cylinder temperature, in-cylinder components and concentrations. Therefore, accurate control is required for reliable and efficient HCCI combustion. This paper outlines a simplified gasoline-fueled HCCI engine model implemented in Simulink environment. The model is able to run in real-time and with fixed simulation steps with the aim of cycle-to-cycle control and hardware- in-the-loop simulation. With the aim of controlling the desired amount of the trapped exhaust gas recirculation （EGR） from the previous cycle, the phase of the intake and exhaust valves and the respective profiles are designed to vary in this model. The model is able to anticipate the auto-ignition timing and the in-cylinder pressure and temperature. The validation has been conducted using a comparison of the experimental results on Ricardo Hydro engine published in a research by Tianjin University and a JAGUAR V6 HCCI test engine at the University of Birmingham. The comparison shows the typical HCCI combustion and a fair agreement between the simulation and experimental results.展开更多
In order to solve the failure of fuel system when using petroleum coke oil slurry (PCOS) in a R180 diesel engine directly,a petroleum coke oil slurry fuel system (PCOSFS) was developed and installed in R180 engine,whi...In order to solve the failure of fuel system when using petroleum coke oil slurry (PCOS) in a R180 diesel engine directly,a petroleum coke oil slurry fuel system (PCOSFS) was developed and installed in R180 engine,which was called PCOS engine.In order to analyze performances and emissions of the PCOS engine,a comparative experiment between PCOS engine fueled with PCOS and R180 engine fueled with diesel oil was carried out.The results show that the PCOS engine can run smoothly,the maximum output power decreases by about 6.2% and 19.0% and the maximum brake thermal efficiency reduces by around 5.85% and 4.13% as compared to R180 engine under the conditions of 1 200 and 1 600 r/min.The HC emissions of PCOS engine are lower than those of R180 engine at 1 200 r/min,and are close to those of R180 engine at 1 600 r/min.The CO emissions are similar to R180 engine at 1 200 and 1 600 r/min.The smoke intensity is close to R180 engine at 1 200 r/min,and is higher than R180 engine at 1 600 r/min.The particles emitted from PCOS engine array sparsely,but particles emitted from R180 engine array closely,cohering together.展开更多
The negative valve overlap (NVO) strategy of HCCI operation was experimentally investigated on a gasoline HCCI engine operated with variable valve timing in association with the addition of diesel fuel. The experiment...The negative valve overlap (NVO) strategy of HCCI operation was experimentally investigated on a gasoline HCCI engine operated with variable valve timing in association with the addition of diesel fuel. The experimental results show that, by using gasoline and diesel blended fuels, the required NVO interval for suitable HCCI combustion under a given engine speed and a moderate compression ratio condition could be reduced, and the HCCI combustion region was extended remarkably without substantial increase in NOx emissions under a given inlet and exhaust valve timing due to the improvement of charge ignitability. In addition, the possible scale of NVO was extended. A substantial increase in the lean limit of excess air ratio and the upper limit of load range can be achieved because of higher volumetric efficiency, resulting from the decrease in the required NVO and the presence of less residual gases in cylinder.展开更多
To reduce their fuel related logistic burden,North Atlantic Treaty Organization(NATO)Armed Forces are advancing the use of a single fuel for both aircraft and ground equipment.To this end,F-34(the commercial equivalen...To reduce their fuel related logistic burden,North Atlantic Treaty Organization(NATO)Armed Forces are advancing the use of a single fuel for both aircraft and ground equipment.To this end,F-34(the commercial equivalent is Jet A-1)is replacing distillate diesel fuel in many applications.However,tests conducted with this kerosene type on high frequency reciprocating rig showed that this type of fuel causes unacceptable wear.This excessive wear is caused by the poor lubricity of aviation fuel.In order to make this type of fuel compatible with direct injection compression engines,seven di-carboxylic acid esters have tested to improve the lubricity of kerosene.Tribological results showed that all esters tested in this series of experiments seem to be suitable for increasing the kerosene lubricity to a satisfactory level.展开更多
Gasoline direct injection(GDI)engines are currently the dominant powertrains for passenger cars.With the implementation of increasingly stringent fuel consumption and emission regulationsworldwide,GDI engines are faci...Gasoline direct injection(GDI)engines are currently the dominant powertrains for passenger cars.With the implementation of increasingly stringent fuel consumption and emission regulationsworldwide,GDI engines are facing challenges owing to high particulate matter emissions and a tendency to knock,leading to a change in the research and design(R&D)issues compared with those in the twentieth century.This paper reviews the progress in research regarding GDI engine technologies over the past 20 years,focusing on combustion system configurations,and also highlights common issues in GDI R&D,including pre-ignition and deto-knock,soot formation and PM emissions,injector deposits and gasoline compression ignition(GCI).First,an overview of recent developments in the field as driven by regulations is provided,following which progress in injection and combustion systems is examined.Third,the review addresses the occurrence and mechanism of deto-knock and considers means of suppressing this phenomenon.The fourth section discusses soot formation mechanisms and particulate matter emission characteristics of GDI engines and describes the application of gasoline particulate filter(GPF)after-treatment.The subsequent section summarizes studies regarding injector deposit formation,as well as pioneering research into GCI combustion modes.Finally,a summary and future prospects for GDI engine technologies are provided.展开更多
Gasoline compression ignition(GCI)combustion faces problems such as high maximum pressure rise rate(MPRR)and combustion deterioration at high loads.This paper aims to improve the engine performance of the GCI mode by ...Gasoline compression ignition(GCI)combustion faces problems such as high maximum pressure rise rate(MPRR)and combustion deterioration at high loads.This paper aims to improve the engine performance of the GCI mode by regulating concentration stratification and promoting fuel-gas mixing by utilizing the double main-injection(DMI)strategy.Two direct injectors simultaneously injected gasoline with an octane number of 82.7 to investigate the energy ratio between the two main-injection and exhaust gas recirculation(EGR)on combustion and emissions.High-load experiments were conducted using the DMI strategy and compared with the single main-injection(SMI)strategy and conventional diesel combustion.The results indicate that the DMI strategy have a great potential to reduce the MPRR and improve the fuel economy of the GCI mode.At a 10 bar indicated mean effective pressure,increasing the main-injection-2 ratio(Rm-2)shortens the injection duration and increases the mean mixing time.Optimized Rm-2 could moderate the trade-off between the MPRR and the indicated specific fuel consumption with both reductions.An appropriate EGR should be adopted considering combustion and emissions.The DMI strategy achieves a highly efficient and stable combustion at high loads,with an indicated thermal efficiency(ITE)greater than 48%,CO and THC emissions at low levels,and MPRR within a reasonable range.Compared with the SMI strategy,the maximum improvement of the ITE is 1.5%,and the maximum reduction of MPRR is 1.5 bar/°CA.展开更多
This paper experimentally and numerically studied the effects of fuel combination and intake valve opening(IVO)timing on combustion and emissions of an n-heptane and gasoline dual-flicl homogeneous charge compression ...This paper experimentally and numerically studied the effects of fuel combination and intake valve opening(IVO)timing on combustion and emissions of an n-heptane and gasoline dual-flicl homogeneous charge compression ignition(HCCI)engine.By changing the gasoline fraction(GF)from 0」to 0.5 and the IVO timing from-15°CA ATDC to 35°CA ATDC,the in-cylinder pressure traces,heat release behaviors,and HC and CO emissions were investigated.The results showed that both the increased GF and the retarded IVO timing delay the combustion phasing,lengthen the combustion duration,and decrease the peak heat release rate and the maximum average combustion temperature,whereas the IVO timing has a more obvious influence on combustion than GF.HC and CO emissions are decreased with reduced GF,advanced IVO timing and increased operational load.展开更多
文摘Experimental study on homogeneous charge compression ignition （HCCI） combustion process was carried out on a single-cylinder direct injection diesel engine fueled with dimethyl ether（DME）. The influence of inert gas CO2 on the ignition and combustion process was investigated. The research results indicate that because of the high cetane number of DME, the stable HCCI operating range is quite narrow while the engine has a high compression ratio. The HCCI operating range can be largely extended when the inert gas is inducted into the charging air. HCCI combustion of DME presents remarkable characteristic of two-stage combustion process. As the concentration of inert gas increases, the ignition timing of the first combustion stage delays, the peak heat release rate decreases, and the combustion duration extends. Inducting inert gas into charging air cannot make the combustion and heat release of DME occur at a perfect crank angle position. Therefore,to obtain HCCI operation for the fuel with high cetane number,other methods such as reducing engine compression ratio should be adopted. Emission results show that under HCCI operation, a nearly zero NOx emission can be obtained with no smoke emissions. But the HC and CO emissions are high, and both rise with the increase of the concentration of inert gases.
基金This project is supported by National Basic Research Program of China (973Program, No. 2001CB209205)National Natural Science Foundation ofChina (No. 50406016)
文摘The effects of cooled external exhaust gas recirculation （EGR） on the combustion and emission performance of diesel fuel homogeneous charge compression ignition （HCCI） are studied. Homogeneous mixture is formed by injecting fuel in-cylinder in the negative valve overlap （NVO） period. So, the HCCI combustion which has low NOx and smoke emission is achieved. Cooled external EGR can delay the start of combustion effectively, which is very useful for high cetane fuel （diesel） HCCI, because these fuels can easily self-ignition, which makes the start of combustion more early. External EGR can avoid the knock combustion of HCCI at high load which means that the EGR can expand the high load limit. HCCI maintains low smoke emission at various EGR rate and various load compared with conventional diesel engine because there is no fuel-rich area in cylinder.
基金sponsored by the projects of National Natural Science Foundation of China (Grant Nos.51806127 and 52075307)Key Research and Development Program of Shandong Province (Grant No.2019GHZ016).
文摘Gasoline compression ignition(GCI)has been considered as a promising combustion concept to yield ultralow NOX and soot emissions while maintaining high thermal efficiency.However,how to improve the low-load performance becomes an urgent issue to be solved.In this paper,a GCI engine model was built to investigate the effects of internal EGR(i-EGR)and pre-injection on in-cylinder temperature,spatial concentration of mixture and OH radical,combustion and emission characteristics,and the control strategy for improving the combustion performance was further explored.The results showed an obvious expansion of the zone with an equivalence ratio between 0.8∼1.2 is realized by higher pre-injection ratios,and the s decreases with the increase of pre-injection ratio,but increases with the increase of i-EGR ratio.The high overlap among the equivalentmixture zone,the hightemperature zone,and the OH radical-rich zone can be achieved by higher i-EGR ratio coupled with higher preinjection ratio.By increasing the pre-injection ratio,the combustion efficiency increases first and then decreases,also achieves the peak value with a pre-injection ratio of 60%and is unaffected by i-EGR.The emissions of CO,HC,NOX,and soot can also be reduced to low levels by the combination of higher i-EGR ratios and a pre-injection ratio of 60%.
基金supported by the National Natural Science Foundation of China(Grant Nos.51425602 and 51961135105)
文摘Gasoline compression ignition(GCI) is a practicable way to obtain low emissions and high thermal efficiency of gasoline-like fuels in internal combustion engines. In this paper, the research octane number(RON) and injection strategy were coordinated to optimize the GCI engine performance and emissions under high loads. The direct injection and port injection were used to achieve two injection strategies: direct injection(DI) and port injection plus direct injection(PIDI), and the primary reference fuels(PRF) with the RON of 60, 70, 80 and 90 were used. The results show that using lower RON fuels under high loads, DI mode can achieve higher efficiency, while PIDI mode can achieve lower combustion noise at an expense of slightly lower fuel economy. When the DI mode is converted to PIDI mode with a pre-injection ratio of 30%, using PRF70 under 12 bar and the exhaust gas recirculation(EGR) rate of 40%, the gross indicated thermal efficiency and the maximum pressure rise rate are reduced by 1% and by 2 bar/°CA, respectively, while the particle emissions also decrease significantly, thus achieving low emissions and high efficiency. However, under the same load and EGR rate, DI mode produces less regulated and unregulated emissions than PIDI mode. In addition, the effect of fuel RON was obvious, the lower RON fuels exhibit obvious three-stage heat release in PIDI mode, however, PRF90 with higher RON only exhibits two-stage heat release, and the peak value of the firststage heat release rate is also lower than those of other fuels.
文摘The detailed surface reaction mechanism of methane on rhodium catalyst was analyzed. Comparisons between numerical simulation and experiments showed a basic agreement. The combustion process of homogeneous charge compression ignition （HCCI） engine whose piston surface has been coated with catalyst （rhodium and platinum） was numerically investigated. A multi-dimensional model with detailed chemical kinetics was built. The effects of catalytic combustion on the ignition timing, the temperature and CO concentration fields, and HC, CO and NOx emissions of the HCCI engine were discussed. The results showed the ignition timing of the HCCI engine was advanced and the emissions of HC and CO were decreased by the catalysis.
文摘Sclerocarya birrea(Marula)seed oil was extracted and characterized for its physico-chemical properties and fatty acid compositions,respectively,by using standardized laboratory methods of the Association of Official and Analytical Chemist(AOAC).The fuel and lubrication properties of marula oil were also determined by using the ASTM methods,and the oil was evaluated in terms of its antiwear,viscometrics,volatility,stability,environmental compatibility properties and energy content.It was found that the high percentage of mono-unsaturated oleic acid(73.6%)provided the oiliness that makes marula oil a natural alternative to genetically modify high oleic acid sunflower oil used in biodiesel production.The aggregate properties of seed oiliness as exemplified by the high oleic acid content,high saponification value(178.6 mg/KOH)and viscosity(41 mm2/s)makes marula oil to be prospective based oil for engine crank case biolubricants with antiwear and friction reduction properties.However,the higher oil viscosity exhibited by marula seed oil in comparison to diesel could pose some durability problems to compression ignition engines,when used directly as fuel.Nonetheless,the reduction of oil viscosity would be required by heating,blending with diesel fuel,or by transesterification to forestall the risk of engine failure resulting from the use of unmodified marula oil.The flash point of marula oil(235℃)is somewhat close to that of monograde SAE 40 mineral oil(240℃),and appreciably higher than that of diesel fuel(52℃).The high flash point makes the seed oil less flammable and ensures safer handling and transportation.While,the low pour point(-13.7℃)ensures the oil usability for engines at cold start and under low load conditions.The oxidation stability of marula oil is ascribed to the traces of natural antioxidants presented in the oil and improves the oil’s shelf life,notwithstanding the high peroxide value(4.58 mequiv/kg),and linolenic acid content(0.3%),which ought to have been the culprit for lipolytic hydrolysis and rancidity.Furthermore,marula seed oil is more biodegradable and environmentally friendly than oils derived from petroleum crude.The closely related cetane number(47.8)and heating values(38.2 mJ/kg)of marula oil to diesel fuel would undeniably sustain the combustion efficiency of diesel fuel and also supply a comparable engine performance output in compression ignition engines.The candidacy of marula seed oil,as a bioenergy resource for alternative fuel,fuel additives and lubricants,will no doubt expand the energy supply mix,conserve fossil fuel reserves and mitigate environmental contamination.
基金supported by the National Natural Science Foundation of China(Grant Nos.51961135105,51425602)。
文摘The internal combustion engines can remain the advantage over competitor technologies for automotive driven,especially the engine efficiency,exceeded 50%while maintaining ultra-low emissions.In this paper,a novel combustion mode characterized by dual high-pressure common-rail direct injection systems,denoted as intelligent charge compression ignition(ICCI)combustion,is proposed to realize high efficiency and clean combustion in wide engine operating ranges.Specifically,commercial gasoline and diesel,which are considered to be complementary in physical and chemical properties,are directly injected into the cylinder by the two independent injection systems,respectively.Through this unique design,the in-cylinder air-fuel mixtures can be flexibly adjusted by regulating injection timing and duration of different fuels,consequently obtaining suitable combustion phase and heat release rate.The ICCI mode can widely run from indicated mean effective pressure 2 bar to 16 bar with an utterly controllable cylinder pressure rising rate,around 50%indicated thermal efficiency and low NOxemissions.A series of experiments were carried out to compare the combustion and emissions of ICCI with other combustion modes(including conventional diesel combustion,reactivity-controlled compression ignition,partially premixed combustion,and gasoline compression ignition).The results show that at the medium engine loads,ICCI mode can reach much high indicated thermal efficiency,especially up to 52%along with extremely low NOxemissions.Prospectively,ICCI mode can realize real-time adjustments of in-cylinder mixture stratification and instantaneous combustion mode switch in one cycle at any operating conditions,and has an excellent commercial application prospect for energy conservation and environmental improvement.
基金Hebei Provincial Science and Technology Research Project(Grant No.Z2015092)Langfang Science and Technology Bureau High-Tech Support Project(Grant No.2016011018)Yanjing Institute of Technology Research Project(Grant No.2017YITSRF105)are thanked for joint funding.
文摘To meet the requirements of the homogeneous charge compression ignition gasoline engine’s rapid cylinder exhaust gas rate and accurate control of combustion phasing,a residual exhaust gas rate model was proposed.A heat dissipation model for gas flow in the exhaust passage and exhaust pipe was established,and the exhaust gas was established.Flow through the exhaust valve was considered as an adiabatic expansion process,the exhaust temperature was used to estimate the temperature in the cylinder at the time that the valve was closed,and the cylinder exhaust gas rate was calculated.To meet the requirements of transient operating conditions,a first-order inertial link was used to correct the thermocouple temperature measurement.Addressing this delay problem and modification of the exhaust wall temperature according to different conditions effectively improved the accuracy of the model.The relative error between the calculated results of this model and the simulation results determined using GT-POWER software was within 3.5%.
基金The Scientific and Technological Research Council of Turkey(TUBITAK)is greatly acknowledgment for financial support with project numbered 118M650.
文摘Recently, reactivity controlled compression ignition (RCCI) has been proposed inorder to achieve a higher thermal efficiency with lower emissions than conventional combustion. In RCCI mode, as the fuel types and their combinations affects the reactivity stratificationinside cylinder, thus combustion control, in present study, iso-propanol was evaluated as lowreactivity fuel (LRF) when petroleum diesel, commercial biodiesel and their blends were highreactivity fuels. It is of great importance that iso-propanol and biodiesel be used together inRCCI mode, as they significantly affect the in-cylinder stratification due to their high octane/cetane number. Therefore, the reactivity controlled compression ignition (RCCI) combustioncharacteristics was investigated in a diesel research engine using iso-propanol, petroleumdiesel, biodiesel and their blends as fuels. Tests were conducted on varying loadings (from20% to 60% of max torque) and premixed ratios of LRF (Rp Z 0, 0.15, 0.30, 0.45, and0.60) at a constant engine speed of 2400 rpm. Results, which were compared with conventionaldiesel combustion (CDC), showed that, as the premixed ratio (Rp) of low-reactivity fuel (isopropanol) increased, ignition delay (ID) period prolonged while combustion duration (CD) and rate of pressure rise (RoPR) reduced assisted to reduce NO emissions and smoke opacity in theexhaust. NO and smoke opacity reduced simultaneously for biodiesel-propanol combinationsup to 40% under 20% load and 0.60 premixed ratio of LRF compared to CDC. Propanol premixed ratio of 0.30 at 60% load was found to be optimum concerning lowest emissions. In conventional mode, HC emissions reduced by up to 52% when biodiesel and its blends with dieselfuel are used, whereas they increased significantly in RCCI mode. According to overall results,it is concluded that RCCI performed better than CDC at entire load.
基金This work was supported by the Natural Science Foundation of Anhui Province （No.090412030）.
文摘Ignition timing control is of great importance in homogeneous charge compression ignition engines. The effect of hydrogen addition on methane combustion was investigated using a CHEMKIN multi-zone model. Results show that hydrogen addition advances ignition tim- ing and enhances peak pressure and temperature. A brief analysis of chemical kinetics of methane blending hydrogen is also performed in order to investigate the scope of its appli- cation, and the analysis suggests that OH radical plays an important role in the oxidation. Hydrogen addition increases NOx while decreasing HC and CO emissions. Exhaust gas recir- culation （EGR） also advances ignition timing; however, its effects on emissions are generally the opposite. By adjusting the hydrogen addition and EGR rate, the ignition timing can be regulated with a low emission level. Investigation into zones suggests that NOx is mostly formed in core zones while HC and CO mostly originate in the crevice and the quench layer.
基金Supported by the National Key Basic Research Development Project of China(No.2001CB209201).
文摘The catalytic combustion of methane in a mierochannel whose surface was coated with platinum（Pt） catalyst was studied by numerical-simulation. The effects of gas-phase reactions on the whole catalytic combustion process were analyzed at a high inlet pressure. A sensitivity analysis of the detailed mechanisms of the surface reaction of methane on Pt revealed that the most sensitive reactions affecting the heterogeneous ignition are oxygen adsorption/desorption and methane adsorption, and the most sensitive reactions affecting the homogeneous ignition are OH and H2O adsorption/desorption. The combustion process of the homogeneous charge compression ignition（HCCI） engine whose piston face was coated with Pt catalyst was simulated. The effects of catalysis and the most sensitive reactions on the ignition timing and the concentration of the main intermediate species during the HCCI engine combustion are discussed. The results show that the ignition timing of the HCCI engine can be increased by catalysis, and the most sensitive reactions affecting the ignition timing of the HCCI engine are OH and H2O adsorption/desorption.
基金Project supported by Singapore Ministry of Education Academic Research Fund Tier 2(R265000498112)
文摘Near dense Mg 0.5 wt.% Zr（0,1,2.5 and 4） wt.% La alloys were successfully synthesized by disintegrated melt deposition technique followed by hot extrusion and were characterized for their microstructural, ignition, hardness, tensile and compression properties. Combined effects of Zr and La assisted in significant grain refinement of Mg and Mg 0.5 wt.% Zr 4 wt.% La exhibited an average grain size as low as ~2.75 μm. High ignition temperature of ~645 oC was realized with Mg 0.5 wt.% Zr（1,2.5 and 4） wt.% La alloys. Microhardness value as high as ~103 Hv was observed with Mg 0.5 wt.% Zr 4 wt.% La alloy. Under room temperature tensile and compression loading, significant improvements in the strength properties of pure Mg with the addition of 0.5 wt.% Zr（0, 1, 2.5 and 4） wt.% La was observed. Mg 0.5 wt.% Zr 4 wt.% La exhibited the maximum 0.2% tensile and compression yield strengths of ~283 MPa and ~264 MPa, respectively. The tensile and compression fracture strain values of synthesized pure Mg were found to be unaffected with the addition of 0.5 wt.% Zr. But the tensile fracture strain reduced with the addition of La while the compressive fracture strain was unaffected. Minimal tensile-compression asymmetry（~1） was exhibited by Mg 0.5 wt.% Zr（1 and 2.5） wt.% La alloys.
文摘This paper examines the effect of equalizing ignition delay in a compression ignition engine.Two sets of tests were conducted,i.e.a set of constant injection timing tests with start of fuel injection at 10°crank angle degree(CAD)before top dead center(BTDC)and a set of constant ignition timing tests while also keeping the 10℃AD BTDC injection and adding ignition improver(2-ethylhexylnitrate-,2-EHN)to the fuel mixtures.Soot particles were characterized using DMS-500 instrument in terms of mass,size,and number.The experimental results showed that adding 2-EHN to the model fuel blends reduced the soot surface area,soot mass concentration and soot mean size.Replacing 20 vol%of a C 7-heptane with 20 vol%methyl-decanoate(an oxygenated C 11 molecule)did not affect the ignition delay or rate of fuel air premixing,the peak in-cylinder pressure or heat release rates.Toluene addition(0−22.5 vol%)to heptane increased the mean size of the soot particles generated by only 3%while also resulted in a slight increase in the peak cylinder pressure and peak heat release rates.Blending toluene and methyl-decanoate into heptane without adding 2-EHN increased the premix phase fraction by at least 13%.However,by adding 2-EHN(4×10^(−4)−1.5×10^(−3)),the premixed phase fraction decreased by at least 11%.
文摘For homogeneous charge compression ignition （HCCI） combustion, the auto-ignition process is very sensitive to in-cylinder conditions, including in-cylinder temperature, in-cylinder components and concentrations. Therefore, accurate control is required for reliable and efficient HCCI combustion. This paper outlines a simplified gasoline-fueled HCCI engine model implemented in Simulink environment. The model is able to run in real-time and with fixed simulation steps with the aim of cycle-to-cycle control and hardware- in-the-loop simulation. With the aim of controlling the desired amount of the trapped exhaust gas recirculation （EGR） from the previous cycle, the phase of the intake and exhaust valves and the respective profiles are designed to vary in this model. The model is able to anticipate the auto-ignition timing and the in-cylinder pressure and temperature. The validation has been conducted using a comparison of the experimental results on Ricardo Hydro engine published in a research by Tianjin University and a JAGUAR V6 HCCI test engine at the University of Birmingham. The comparison shows the typical HCCI combustion and a fair agreement between the simulation and experimental results.
基金Project(2007BAA09B05)supported by the National Key Technology Research and Development Program of ChinaProject(50804004)supported by the National Natural Science Foundation of China
文摘In order to solve the failure of fuel system when using petroleum coke oil slurry (PCOS) in a R180 diesel engine directly,a petroleum coke oil slurry fuel system (PCOSFS) was developed and installed in R180 engine,which was called PCOS engine.In order to analyze performances and emissions of the PCOS engine,a comparative experiment between PCOS engine fueled with PCOS and R180 engine fueled with diesel oil was carried out.The results show that the PCOS engine can run smoothly,the maximum output power decreases by about 6.2% and 19.0% and the maximum brake thermal efficiency reduces by around 5.85% and 4.13% as compared to R180 engine under the conditions of 1 200 and 1 600 r/min.The HC emissions of PCOS engine are lower than those of R180 engine at 1 200 r/min,and are close to those of R180 engine at 1 600 r/min.The CO emissions are similar to R180 engine at 1 200 and 1 600 r/min.The smoke intensity is close to R180 engine at 1 200 r/min,and is higher than R180 engine at 1 600 r/min.The particles emitted from PCOS engine array sparsely,but particles emitted from R180 engine array closely,cohering together.
基金Supported by the Engineering and Physical Sciences Research Council of the UK(No58338/01)
文摘The negative valve overlap (NVO) strategy of HCCI operation was experimentally investigated on a gasoline HCCI engine operated with variable valve timing in association with the addition of diesel fuel. The experimental results show that, by using gasoline and diesel blended fuels, the required NVO interval for suitable HCCI combustion under a given engine speed and a moderate compression ratio condition could be reduced, and the HCCI combustion region was extended remarkably without substantial increase in NOx emissions under a given inlet and exhaust valve timing due to the improvement of charge ignitability. In addition, the possible scale of NVO was extended. A substantial increase in the lean limit of excess air ratio and the upper limit of load range can be achieved because of higher volumetric efficiency, resulting from the decrease in the required NVO and the presence of less residual gases in cylinder.
文摘To reduce their fuel related logistic burden,North Atlantic Treaty Organization(NATO)Armed Forces are advancing the use of a single fuel for both aircraft and ground equipment.To this end,F-34(the commercial equivalent is Jet A-1)is replacing distillate diesel fuel in many applications.However,tests conducted with this kerosene type on high frequency reciprocating rig showed that this type of fuel causes unacceptable wear.This excessive wear is caused by the poor lubricity of aviation fuel.In order to make this type of fuel compatible with direct injection compression engines,seven di-carboxylic acid esters have tested to improve the lubricity of kerosene.Tribological results showed that all esters tested in this series of experiments seem to be suitable for increasing the kerosene lubricity to a satisfactory level.
基金The authors acknowledge theChina NationalNat-ural Science Foundation Project“Formation and Evolution of PM from GDI Engines:From Primary Particles to Secondary Aerosols”(Grant No.51636003)the National Key R&D Plan Project“Integration Technology of PM Capture and Clean Emissions for GDI Vehicles”(Grant No.2017YFC02110004).
文摘Gasoline direct injection(GDI)engines are currently the dominant powertrains for passenger cars.With the implementation of increasingly stringent fuel consumption and emission regulationsworldwide,GDI engines are facing challenges owing to high particulate matter emissions and a tendency to knock,leading to a change in the research and design(R&D)issues compared with those in the twentieth century.This paper reviews the progress in research regarding GDI engine technologies over the past 20 years,focusing on combustion system configurations,and also highlights common issues in GDI R&D,including pre-ignition and deto-knock,soot formation and PM emissions,injector deposits and gasoline compression ignition(GCI).First,an overview of recent developments in the field as driven by regulations is provided,following which progress in injection and combustion systems is examined.Third,the review addresses the occurrence and mechanism of deto-knock and considers means of suppressing this phenomenon.The fourth section discusses soot formation mechanisms and particulate matter emission characteristics of GDI engines and describes the application of gasoline particulate filter(GPF)after-treatment.The subsequent section summarizes studies regarding injector deposit formation,as well as pioneering research into GCI combustion modes.Finally,a summary and future prospects for GDI engine technologies are provided.
基金supported by the National Key R&D Program of China(Grant No.2022YFE0100100).
文摘Gasoline compression ignition(GCI)combustion faces problems such as high maximum pressure rise rate(MPRR)and combustion deterioration at high loads.This paper aims to improve the engine performance of the GCI mode by regulating concentration stratification and promoting fuel-gas mixing by utilizing the double main-injection(DMI)strategy.Two direct injectors simultaneously injected gasoline with an octane number of 82.7 to investigate the energy ratio between the two main-injection and exhaust gas recirculation(EGR)on combustion and emissions.High-load experiments were conducted using the DMI strategy and compared with the single main-injection(SMI)strategy and conventional diesel combustion.The results indicate that the DMI strategy have a great potential to reduce the MPRR and improve the fuel economy of the GCI mode.At a 10 bar indicated mean effective pressure,increasing the main-injection-2 ratio(Rm-2)shortens the injection duration and increases the mean mixing time.Optimized Rm-2 could moderate the trade-off between the MPRR and the indicated specific fuel consumption with both reductions.An appropriate EGR should be adopted considering combustion and emissions.The DMI strategy achieves a highly efficient and stable combustion at high loads,with an indicated thermal efficiency(ITE)greater than 48%,CO and THC emissions at low levels,and MPRR within a reasonable range.Compared with the SMI strategy,the maximum improvement of the ITE is 1.5%,and the maximum reduction of MPRR is 1.5 bar/°CA.
基金the National Natural Science Foundation of China(Grant Nos.51861135303 and 51776124)the Shanghai Science and Technology Committee,China(Grant No.19160745400).
文摘This paper experimentally and numerically studied the effects of fuel combination and intake valve opening(IVO)timing on combustion and emissions of an n-heptane and gasoline dual-flicl homogeneous charge compression ignition(HCCI)engine.By changing the gasoline fraction(GF)from 0」to 0.5 and the IVO timing from-15°CA ATDC to 35°CA ATDC,the in-cylinder pressure traces,heat release behaviors,and HC and CO emissions were investigated.The results showed that both the increased GF and the retarded IVO timing delay the combustion phasing,lengthen the combustion duration,and decrease the peak heat release rate and the maximum average combustion temperature,whereas the IVO timing has a more obvious influence on combustion than GF.HC and CO emissions are decreased with reduced GF,advanced IVO timing and increased operational load.
