A 1/3-scale reinfored concrete(RC) frame of unequal storey height with specially shaped columns was tested under low frequency cyclic loading.The damage characteristic,bearing capacity,deformation capacity and ductili...A 1/3-scale reinfored concrete(RC) frame of unequal storey height with specially shaped columns was tested under low frequency cyclic loading.The damage characteristic,bearing capacity,deformation capacity and ductility were analyzed.The restoring force model of the frame was obtained based on the study of the hysteresis curve measured in experiment,and the stiffness degeneration characteristics of every storey of the frame were analyzed.Finally the accumulated damage was analyzed with the damage assessment model.It is shown that the seismic behavior of this frame of unequal storey height with specially shaped columns is generally good,but the bottom of first floor column is a weak part,which should be paid more attention in design,and the restoring force model derived from this experiment can be seen as a valuable guide for design and non-linear finite element analysis for this kind of structure.展开更多
This paper examines the quasi-static cyclic behavior, lateral strength and equivalent damping capacities of a system of post-tensioned segmental bridge columns tied with large diameter martensitic Shape Memory Alloy ...This paper examines the quasi-static cyclic behavior, lateral strength and equivalent damping capacities of a system of post-tensioned segmental bridge columns tied with large diameter martensitic Shape Memory Alloy （SMA） link-bars. Moment-curvature constitutive relationships are formulated and analysis tools are developed for the PT column, including a modified four-spring model prepared for the SMA bars. The suggested system is exemplified using a column with an aspect ratio of 7.5 and twelve 36.5 mm diameter NiTi martensitic SMA bars. A post-tensioning force of 40% to 60% of the tendon yield strength is applied in order to obtain a self re-centering system, considering the residual stress of the martensitie SMA bars. The cyclic response results show that the lateral strength remains consistently around 10% of the total vertical load and the equivalent viscous damping ratios reach 10%-12% of critical. When large diameter NiTi superelastic SMA bars are incorporated into the column system, the cyclic response varies substantially. The creep behavior of the superelastic SMA bar is accounted for since it affects the re-centering capability of the column. Two examples are presented to emphasize the modeling sensitivities for these special bars and quantify their cyclic behavior effects within the column assembly.展开更多
In order to study the seismic behavior of frame with specially shaped columns,the hysteretic curve was analyzed based on a quasi-static test of a two-span,three-story frame with specially shaped columns.The top layer ...In order to study the seismic behavior of frame with specially shaped columns,the hysteretic curve was analyzed based on a quasi-static test of a two-span,three-story frame with specially shaped columns.The top layer framework curve and the corresponding resilience model were obtained from the hysteretic curve.And the stiffness and strength degeneration were also investigated.The results indicated that the stiffness degeneration is not obvious,thus the frame with specially shaped columns has high earthquake-resistant behavior.The resilience model calculated from the test can provide reference for design and nonlinear finite element analysis.展开更多
To investigate the seismic behavior of specially shaped column joints with X-shaped reinforcement,two groups of specimens with or without X-shaped reinforcement in joint core region were tested under constant axial co...To investigate the seismic behavior of specially shaped column joints with X-shaped reinforcement,two groups of specimens with or without X-shaped reinforcement in joint core region were tested under constant axial compression load and low reversed cyclic loading,which imitated low to moderate earthquake force.The seismic behavior of specially shaped column joints with X-shaped reinforcement in terms of bearing capacity,displacement,ductility,hysteretic curve,stiffness degradation and energy dissipation was studied and compared to that without Xshaped reinforcement in joint core region.With the damage estimation model,the accumulated damage was analyzed.The shearing capacity formula of specially shaped column joints reinforced by X-shaped reinforcement was proposed with a simple form.The test results show that X-shaped reinforcement is an effective measure for improving the seismic behavior of specially shaped column joints including deformation behavior,ductility and hysteretic characteristic.All specimens were damaged with gradual stiffness degeneration.In addition,X-shaped reinforcement in the joint core region is an effective way to lighten the degree of cumulated damage.The good seismic performance obtained from the specially shaped column joint with X-shaped reinforcement can be used in engineering applications.The test value is higher than the calculated value,which indicates that the formula is safe for the design of specially shaped column joints.展开更多
Based on the introductions of a type of diaphragm-through connection between concrete-filled square steel tubular columns (CFSSTCs) and H-shaped steel beams,a finite element model of the connection is developed and us...Based on the introductions of a type of diaphragm-through connection between concrete-filled square steel tubular columns (CFSSTCs) and H-shaped steel beams,a finite element model of the connection is developed and used to investigate the seismic behavior of the connection.The results of the finite element model are validated by a set of cyclic loading tests.The cyclic loading tests and the finite element analyses indicate that the failure mode of the suggested connections is plastic hinge at the beam with inelastic rotation angle exceeding 0.04 rad.The suggested connections have sufficient strength,plastic deformation and energy dissipation capacity to be used in composite moment frames as beam-to-column rigid connections.展开更多
Four exterior joints with special-shaped columns which have different lengths of limbs are tested under low cyclic loading. Speeial-shaped columns adopted are L- and T-shaped in section. It can be concluded that crack...Four exterior joints with special-shaped columns which have different lengths of limbs are tested under low cyclic loading. Speeial-shaped columns adopted are L- and T-shaped in section. It can be concluded that crack pattern, failure mode and shear strength of joints are affected by the length of limb, and that shear strength and ductility increase with the length of limb; the joints with the flexural failure of the beam have better seismic behavior than those with the shear failure of the joint core.展开更多
Elastic critical buckling load of a column depends on various parameters,such as boundary conditions,material,and crosssection geometry.The main purpose of this work is to present a new method for investigating the bu...Elastic critical buckling load of a column depends on various parameters,such as boundary conditions,material,and crosssection geometry.The main purpose of this work is to present a new method for investigating the buckling load of tapered columns subjected to axial force.The proposed method is based on modified buckling mode shape of tapered structure and perturbation theory.The mode shape of the damaged structure can be expressed as a linear combination of mode shapes of the intact structure.Variations in length in piecewise form can be positive or negative.The method can be used for single-span and continuous columns.Comparison of results with those of finite element and Timoshenko methods shows the high accuracy and efficiency of the proposed method for detecting buckling load.展开更多
Oscillating Water Column （OWC） wave energy converting system is one of the most widely used facilities all over the world. The air chamber is utilized to convert the wave energy into the pneumatic energy. The numeri...Oscillating Water Column （OWC） wave energy converting system is one of the most widely used facilities all over the world. The air chamber is utilized to convert the wave energy into the pneumatic energy. The numerical wave tank based on the two-phase VOF model is established in the present study toinvestigate the operating performance of OWC air chamber. The RANS equations, standard k-ε turbulence model and dynamic mesh technology are employed in the numerical model. The effects of incident wave conditions and shape parameters on the wave energy converting efficiency are studied and the capability of the present numerical wave tank on the corresponding engineering application is validated.展开更多
基金Project(50878141) supported by the National Natural Science Foundation of ChinaProject(Z2010250) supported by the Natural Science Foundation of Education Department of Hebei Province,China
文摘A 1/3-scale reinfored concrete(RC) frame of unequal storey height with specially shaped columns was tested under low frequency cyclic loading.The damage characteristic,bearing capacity,deformation capacity and ductility were analyzed.The restoring force model of the frame was obtained based on the study of the hysteresis curve measured in experiment,and the stiffness degeneration characteristics of every storey of the frame were analyzed.Finally the accumulated damage was analyzed with the damage assessment model.It is shown that the seismic behavior of this frame of unequal storey height with specially shaped columns is generally good,but the bottom of first floor column is a weak part,which should be paid more attention in design,and the restoring force model derived from this experiment can be seen as a valuable guide for design and non-linear finite element analysis for this kind of structure.
基金Research fund of Hanyang University Under Grant No.HY-2010-N
文摘This paper examines the quasi-static cyclic behavior, lateral strength and equivalent damping capacities of a system of post-tensioned segmental bridge columns tied with large diameter martensitic Shape Memory Alloy （SMA） link-bars. Moment-curvature constitutive relationships are formulated and analysis tools are developed for the PT column, including a modified four-spring model prepared for the SMA bars. The suggested system is exemplified using a column with an aspect ratio of 7.5 and twelve 36.5 mm diameter NiTi martensitic SMA bars. A post-tensioning force of 40% to 60% of the tendon yield strength is applied in order to obtain a self re-centering system, considering the residual stress of the martensitie SMA bars. The cyclic response results show that the lateral strength remains consistently around 10% of the total vertical load and the equivalent viscous damping ratios reach 10%-12% of critical. When large diameter NiTi superelastic SMA bars are incorporated into the column system, the cyclic response varies substantially. The creep behavior of the superelastic SMA bar is accounted for since it affects the re-centering capability of the column. Two examples are presented to emphasize the modeling sensitivities for these special bars and quantify their cyclic behavior effects within the column assembly.
基金Supported by Fund of Specially Shaped Column Code of Ministry of Construction of China.
文摘In order to study the seismic behavior of frame with specially shaped columns,the hysteretic curve was analyzed based on a quasi-static test of a two-span,three-story frame with specially shaped columns.The top layer framework curve and the corresponding resilience model were obtained from the hysteretic curve.And the stiffness and strength degeneration were also investigated.The results indicated that the stiffness degeneration is not obvious,thus the frame with specially shaped columns has high earthquake-resistant behavior.The resilience model calculated from the test can provide reference for design and nonlinear finite element analysis.
基金Supported by National Natural Science Foundation of China (No. 50878141)Hebei Natural Science Foundation,China (No. E2011202013)High School of Hebei Science and Technology Research Youth Foundation,China(No. Q2012083)
文摘To investigate the seismic behavior of specially shaped column joints with X-shaped reinforcement,two groups of specimens with or without X-shaped reinforcement in joint core region were tested under constant axial compression load and low reversed cyclic loading,which imitated low to moderate earthquake force.The seismic behavior of specially shaped column joints with X-shaped reinforcement in terms of bearing capacity,displacement,ductility,hysteretic curve,stiffness degradation and energy dissipation was studied and compared to that without Xshaped reinforcement in joint core region.With the damage estimation model,the accumulated damage was analyzed.The shearing capacity formula of specially shaped column joints reinforced by X-shaped reinforcement was proposed with a simple form.The test results show that X-shaped reinforcement is an effective measure for improving the seismic behavior of specially shaped column joints including deformation behavior,ductility and hysteretic characteristic.All specimens were damaged with gradual stiffness degeneration.In addition,X-shaped reinforcement in the joint core region is an effective way to lighten the degree of cumulated damage.The good seismic performance obtained from the specially shaped column joint with X-shaped reinforcement can be used in engineering applications.The test value is higher than the calculated value,which indicates that the formula is safe for the design of specially shaped column joints.
基金Supported by National Natural Science Foundation of China(No.51268054)Natural Science Foundation of Tianjin(No.13JCQNJC07300)the foundation of Key Laboratory of Coast Civil Structure Safety(Tianjin University),Ministry of Education of China(No.2011-1)
文摘Based on the introductions of a type of diaphragm-through connection between concrete-filled square steel tubular columns (CFSSTCs) and H-shaped steel beams,a finite element model of the connection is developed and used to investigate the seismic behavior of the connection.The results of the finite element model are validated by a set of cyclic loading tests.The cyclic loading tests and the finite element analyses indicate that the failure mode of the suggested connections is plastic hinge at the beam with inelastic rotation angle exceeding 0.04 rad.The suggested connections have sufficient strength,plastic deformation and energy dissipation capacity to be used in composite moment frames as beam-to-column rigid connections.
文摘Four exterior joints with special-shaped columns which have different lengths of limbs are tested under low cyclic loading. Speeial-shaped columns adopted are L- and T-shaped in section. It can be concluded that crack pattern, failure mode and shear strength of joints are affected by the length of limb, and that shear strength and ductility increase with the length of limb; the joints with the flexural failure of the beam have better seismic behavior than those with the shear failure of the joint core.
文摘Elastic critical buckling load of a column depends on various parameters,such as boundary conditions,material,and crosssection geometry.The main purpose of this work is to present a new method for investigating the buckling load of tapered columns subjected to axial force.The proposed method is based on modified buckling mode shape of tapered structure and perturbation theory.The mode shape of the damaged structure can be expressed as a linear combination of mode shapes of the intact structure.Variations in length in piecewise form can be positive or negative.The method can be used for single-span and continuous columns.Comparison of results with those of finite element and Timoshenko methods shows the high accuracy and efficiency of the proposed method for detecting buckling load.
基金supported by the National Natural Science Foundation of China(Grant Nos. 50909089 and 40911140281)Qingdao S&T Development Program(09-1-3-41-jch)Korean Ministry of Land,Transport & Maritime Affairs through KORDI Program
文摘Oscillating Water Column （OWC） wave energy converting system is one of the most widely used facilities all over the world. The air chamber is utilized to convert the wave energy into the pneumatic energy. The numerical wave tank based on the two-phase VOF model is established in the present study toinvestigate the operating performance of OWC air chamber. The RANS equations, standard k-ε turbulence model and dynamic mesh technology are employed in the numerical model. The effects of incident wave conditions and shape parameters on the wave energy converting efficiency are studied and the capability of the present numerical wave tank on the corresponding engineering application is validated.
