An S-band high-gradient accelerating structure is designed for a proton therapy linear accelerator(linac)to accommodate the new development of compact,singleroom facilities and ultra-high dose rate(FLASH)radiotherapy....An S-band high-gradient accelerating structure is designed for a proton therapy linear accelerator(linac)to accommodate the new development of compact,singleroom facilities and ultra-high dose rate(FLASH)radiotherapy.To optimize the design,an efficient optimization scheme is applied to improve the simulation efficiency.An S-band accelerating structure with 2856 MHz is designed with a low beta of 0.38,which is a difficult structure to achieve for a linac accelerating proton particles from 70 to 250 MeV,as a high gradient up to 50 MV/m is required.A special design involving a dual-feed coupler eliminates the dipole field effect.This paper presents all the details pertaining to the design,fabrication,and cold test results of the S-band high-gradient accelerating structure.展开更多
In this paper, cold simulation experiments and numerical calculations are conducted to predict 3 D flow field aerodynamics for an oil furnace after being retrofitted due to its fuel variation. K ε model and SIMPLE ...In this paper, cold simulation experiments and numerical calculations are conducted to predict 3 D flow field aerodynamics for an oil furnace after being retrofitted due to its fuel variation. K ε model and SIMPLE program under body fit coordination (BFC) system, in which TTM non orthogonal method is used to control the irregular geometric boundary, are adopted to solve the control equations. Model tests are conducted to check the calculation results, showing that they are in agreement with each other. Three different alternatives with different side window locations are also calculated to optimize the designs. The field retrofitting results show that the combination of cold tests with numerical calculations has prosperous application in retrofitting or renewing medium and small boilers.展开更多
Intermodal containers have many advantages in the bulk supply chain, but idle times may cause freezing problems for containers in terminals and long-lasting deliveries, especially during the winter time in Nordic cond...Intermodal containers have many advantages in the bulk supply chain, but idle times may cause freezing problems for containers in terminals and long-lasting deliveries, especially during the winter time in Nordic conditions. The aim of the cold tests was to study metal and composite containers’ ability to tolerate wood chips freezing into the inner surface of the container. Two of the containers were normal metal containers and one was a composite container. The loaded containers were put inside the laboratory hall, the temperature of which was -30°C, and kept there for variable times: less than 24 hours. The inner surface of one of metal containers was treated with a special coolant, EC1. After the test, the chips were unloaded, and the container walls were checked to determine whether there was any material left on them. The test results indicated the advantages of composite containers having a thermally insulated structure without freezing problems. At the same time, chips were freezing badly onto the floor of both metal containers. A frozen chip layer with a thickness of approximately 50 cm - 60 cm was stuck to the floors. As such, EC1 did not seem to prevent the freezing of the chips onto the inner surfaces. The results proved that intermodal logistics of truck and train transportation would be more suitable for composite containers than for metal containers in the winter time in Nordic conditions.展开更多
The CBPM is a kind of monitor which is used for the measurement of beam transverse position. It is becoming increasingly popular due to its high potential in resolution performance. In theory, the resolution can reach...The CBPM is a kind of monitor which is used for the measurement of beam transverse position. It is becoming increasingly popular due to its high potential in resolution performance. In theory, the resolution can reach about 1 nanometer. In this paper, a rectangular CBPM is designed for it has better X-Y isolation than a cylindrical one. It has been simulated and measured, and the results agree with each other very well. The procedures and results for the simulation and the cold test will be shown later and it will be proved that this is a reliable method for the CBPM design.展开更多
To further improve the performance of acceler-ators,the first cryogenic normal-conducting RF gun in China was designed and manufactured.As a new and attractive trend,this optimized cryogenic RF gun can generate a low-...To further improve the performance of acceler-ators,the first cryogenic normal-conducting RF gun in China was designed and manufactured.As a new and attractive trend,this optimized cryogenic RF gun can generate a low-emittance beam with a short-driven laser pulse because of its promising high gradient on the cath-ode.In this paper,optimization of the RF design and beam dynamics,including suppression of the peak RF field and elimination of the multipole mode,is presented.In addi-tion,the emittance growth caused by the alignment devi-ation and RF jitter is discussed.After the gun was manufactured,a cold test was conducted at both room temperature and cryogenic conditions.At room tempera-ture,the field distribution was obtained by the bead pull method.Under cryogenic conditions,the RF properties,such as the coupling coefficient and quality factor,varied with temperature.The test results agreed with the design.In the cryogenic test,vibration measurements were performed.Without vibration isolation,a maximum vibration of 50 lm was observed.These cold test results are the basis of the following high-power test.展开更多
An S-band cavity BPM is designed for a new injector in National Synchrotron Radiation Laboratory. A re-entrant position cavity is tuned to the TM110 mode as position cavity. Cut-through waveguides are used as pickups ...An S-band cavity BPM is designed for a new injector in National Synchrotron Radiation Laboratory. A re-entrant position cavity is tuned to the TM110 mode as position cavity. Cut-through waveguides are used as pickups to suppress the monopole signal. Theoretical resolution of this design is 31 nm. A prototype cavity BPM system is manufactured for off-line cold tests. The wire scanning method is used to calibrate the BPM and estimate the performance of the on-line BPM system. A cross-talk problem has been detected during the cold test. Racetrack cavity BPM design can be used to suppress the cross-talk. With the nonlinear effect being ignored, transform matrix can be used to correct cross-talk. Analysis of cold test results shows that the position resolution of prototype BPM is better than 3 μm.展开更多
Based on the similarity theory, taking the horseshoe, city-gate and round linings as examples, the value and distribution regularities of normal frost heaving pressures （hereinafter as frost heaving pressures） in tu...Based on the similarity theory, taking the horseshoe, city-gate and round linings as examples, the value and distribution regularities of normal frost heaving pressures （hereinafter as frost heaving pressures） in tunnels excavated in fractured rock mass in cold regions under different constraints and freezing depths were studied by a test model. It was found that the larger the frozen depth, the larger the frost heaving pressure, and the stronger the top constraint, the larger the frost heaving pressure. For the horseshoe lining and city-gate lining, the top constraint has a greater effect on the frost heaving pressures on the arch and the inverted arch. For the round lining, the influences of the top constraint on the frost heaving pressure in all linings are almost the same. The frost heaving pressure is maximum on the city-gate lining and minimal on the round lining. The largest frost heaving pressure all occur near the foot of the inverted arch for the three kinds of lining. Thus, the test data basically coincide with the observed in situ data.展开更多
Low-tempemture stress is a major abiotic stress influencing plant growth, economic yield and quality worldwide. Precise and reliable identification and test of plant cold resistance is a foundation for exploring low-t...Low-tempemture stress is a major abiotic stress influencing plant growth, economic yield and quality worldwide. Precise and reliable identification and test of plant cold resistance is a foundation for exploring low-temperature damages, cold resistance mechanism of plants, cultivating and innovating quality cold-re- sistant germplasm resources, which is rather important for woody plants because their perennial and large-sized characteristics. Generally, most researches on plant cold-resistant physiology focused on identification and utilization of cold resistance worldwide, and a few on test methods of cold resistance, but cold resistance mechanism has been less reported. Therefore, researches on methods of identifying and testing plant resistance have achieved considerable progress, accumulated much experience and formed characteristics gradually in terms of methodology. Current methods of identifying plant cold resistance include open field/outdoor culti- vation evaluation, cold and frost damage investigation, simulated cold weather, and mathematical model forecast. And the methods of testing plant cold resistance include growth condition test, frozen index investigation, electrolyte leakage, bioelectrical impedance mapping and so on. Synthesizing the methods of identifying and testing plant cold resistance should be a key matter in the present and future researches and application of plant cold resistance physiology, improvement and in- novation of the identification and test will be an important direction of the future researches. Identification and test of plant cold resistance based on genomies, meta- bonomics and proteomics should be the new trend of the researches on physiology and ecology of plant cold resistance.展开更多
Gas Transmitting From West to East Project' is significant. It should ensure the welding quality and safety of pipeline. The task is very arduous to guarantee the quality of the project in the condition of long li...Gas Transmitting From West to East Project' is significant. It should ensure the welding quality and safety of pipeline. The task is very arduous to guarantee the quality of the project in the condition of long line, complex weather and geology features. In this paper, the welding cold cracking susceptibility of domestic X 70 pipeline steel adopted by the project, which is one of the most interesting questions of welding quality about petrol pipeline, was studied by means of oblique Y groove cracking test. The crack ratio of surface and section was tested under the conditions of different welding materials and preheat temperature .The thickness of plate steel was 14.7 mm and 10.3 mm . The results reveal that X 70 pipeline steel has good crack resistance. The research has important value for the construction of large scale pipeline engineering and the application of domestic X 70 pipeline steel.展开更多
We study the interaction of a uniform, cold and collisional plasma with a test charged particle moving off-axis at a constant speed down a cylindrical tube with a resistive thick metallic wall. Upon matching the elect...We study the interaction of a uniform, cold and collisional plasma with a test charged particle moving off-axis at a constant speed down a cylindrical tube with a resistive thick metallic wall. Upon matching the electromagnetic field components at all interfaces, the induced monopole electromagnetic fields in the plasma are obtained in the frequency domain. An expression for the plasma electric resistance and reactance is derived and analyzed numerically for some representative parameters. Near the plasma resonant frequency, the plasma resistance evolves with frequency like a parallel RLC resonator with peak resistance at the plasma frequency pe, while the plasma reactance can be capacitive or inductive in nature depending on the frequency under consideration.展开更多
The energy efficiency design of the exterior wall in the buildings of the hot summer and cold winter zone of China should consider the heat prevention in summer and the heat insulation in winter. The self-insulation o...The energy efficiency design of the exterior wall in the buildings of the hot summer and cold winter zone of China should consider the heat prevention in summer and the heat insulation in winter. The self-insulation of the exterior?wall is a more feasible design to satisfy the energy efficiency of buildings in the?zone. However, the systematic research is urgently needed for the self-insulation of the exterior wall in the hot summer and cold winter zone of China. The paper tested the thermal performance of the common non-clay materials such as shale sintered hollow brick, sand autoclaved aerated concrete block, etc. by means of indoor experiments. The energy efficiency effect of the common materials was verified using dynamic calculation soft PKPM and several constitutions of exterior wall with different main bricks and insulation materials on the heat bridge were simulated, too. Besides, the tests of the thermal performance of exterior wall in real constructions were carried out to testify the practical effect of the recommended constitutions of exterior wall with different main bricks and insulation materials on the heat bridge. The conclusions are: the physical and thermal properties of the six non-clay wall material are better than the clay porous brick;the thermal performance of the non-clay brick can be improved obviously through the rational arrangement of the holes;shale sintered hollow brick after increasing the holes and rationalizing the hole arrangement and sand autoclaved aerated concrete block are recommended for buildings in the hot summer and cold winter area of China. The dynamic calculation results show that the thermal performances?of the non-clay materials are all satisfied with the energy efficiency;The heat transfer coefficient of the exterior wall with composition?③,?in which?the main wall was sand autoclaved aerated concrete block and the material on the heat bridge was sand autoclaved aerated concrete plate, is the smallest among the three recommended compositions.展开更多
基金This work was supported by the Alliance of International Science Organizations(No.ANSO-CR-KP-2020-16).
文摘An S-band high-gradient accelerating structure is designed for a proton therapy linear accelerator(linac)to accommodate the new development of compact,singleroom facilities and ultra-high dose rate(FLASH)radiotherapy.To optimize the design,an efficient optimization scheme is applied to improve the simulation efficiency.An S-band accelerating structure with 2856 MHz is designed with a low beta of 0.38,which is a difficult structure to achieve for a linac accelerating proton particles from 70 to 250 MeV,as a high gradient up to 50 MV/m is required.A special design involving a dual-feed coupler eliminates the dipole field effect.This paper presents all the details pertaining to the design,fabrication,and cold test results of the S-band high-gradient accelerating structure.
文摘In this paper, cold simulation experiments and numerical calculations are conducted to predict 3 D flow field aerodynamics for an oil furnace after being retrofitted due to its fuel variation. K ε model and SIMPLE program under body fit coordination (BFC) system, in which TTM non orthogonal method is used to control the irregular geometric boundary, are adopted to solve the control equations. Model tests are conducted to check the calculation results, showing that they are in agreement with each other. Three different alternatives with different side window locations are also calculated to optimize the designs. The field retrofitting results show that the combination of cold tests with numerical calculations has prosperous application in retrofitting or renewing medium and small boilers.
文摘Intermodal containers have many advantages in the bulk supply chain, but idle times may cause freezing problems for containers in terminals and long-lasting deliveries, especially during the winter time in Nordic conditions. The aim of the cold tests was to study metal and composite containers’ ability to tolerate wood chips freezing into the inner surface of the container. Two of the containers were normal metal containers and one was a composite container. The loaded containers were put inside the laboratory hall, the temperature of which was -30°C, and kept there for variable times: less than 24 hours. The inner surface of one of metal containers was treated with a special coolant, EC1. After the test, the chips were unloaded, and the container walls were checked to determine whether there was any material left on them. The test results indicated the advantages of composite containers having a thermally insulated structure without freezing problems. At the same time, chips were freezing badly onto the floor of both metal containers. A frozen chip layer with a thickness of approximately 50 cm - 60 cm was stuck to the floors. As such, EC1 did not seem to prevent the freezing of the chips onto the inner surfaces. The results proved that intermodal logistics of truck and train transportation would be more suitable for composite containers than for metal containers in the winter time in Nordic conditions.
文摘The CBPM is a kind of monitor which is used for the measurement of beam transverse position. It is becoming increasingly popular due to its high potential in resolution performance. In theory, the resolution can reach about 1 nanometer. In this paper, a rectangular CBPM is designed for it has better X-Y isolation than a cylindrical one. It has been simulated and measured, and the results agree with each other very well. The procedures and results for the simulation and the cold test will be shown later and it will be proved that this is a reliable method for the CBPM design.
基金supported by the National Key R&D Program of China(No.2018YFF0109203)ANSO(ANSO-CR-KP-2020-16).
文摘To further improve the performance of acceler-ators,the first cryogenic normal-conducting RF gun in China was designed and manufactured.As a new and attractive trend,this optimized cryogenic RF gun can generate a low-emittance beam with a short-driven laser pulse because of its promising high gradient on the cath-ode.In this paper,optimization of the RF design and beam dynamics,including suppression of the peak RF field and elimination of the multipole mode,is presented.In addi-tion,the emittance growth caused by the alignment devi-ation and RF jitter is discussed.After the gun was manufactured,a cold test was conducted at both room temperature and cryogenic conditions.At room tempera-ture,the field distribution was obtained by the bead pull method.Under cryogenic conditions,the RF properties,such as the coupling coefficient and quality factor,varied with temperature.The test results agreed with the design.In the cryogenic test,vibration measurements were performed.Without vibration isolation,a maximum vibration of 50 lm was observed.These cold test results are the basis of the following high-power test.
基金supported by the National Natural Science Foundation of China (Grant Nos. 10875117 and 11005106)National "985 Project" (Grnat No. 173123200402002)+1 种基金China Postdoctoral Science Foundation (Grant No. 20100470853)"the Fundamental Research Funds for the Central Universities"
文摘An S-band cavity BPM is designed for a new injector in National Synchrotron Radiation Laboratory. A re-entrant position cavity is tuned to the TM110 mode as position cavity. Cut-through waveguides are used as pickups to suppress the monopole signal. Theoretical resolution of this design is 31 nm. A prototype cavity BPM system is manufactured for off-line cold tests. The wire scanning method is used to calibrate the BPM and estimate the performance of the on-line BPM system. A cross-talk problem has been detected during the cold test. Racetrack cavity BPM design can be used to suppress the cross-talk. With the nonlinear effect being ignored, transform matrix can be used to correct cross-talk. Analysis of cold test results shows that the position resolution of prototype BPM is better than 3 μm.
文摘Based on the similarity theory, taking the horseshoe, city-gate and round linings as examples, the value and distribution regularities of normal frost heaving pressures （hereinafter as frost heaving pressures） in tunnels excavated in fractured rock mass in cold regions under different constraints and freezing depths were studied by a test model. It was found that the larger the frozen depth, the larger the frost heaving pressure, and the stronger the top constraint, the larger the frost heaving pressure. For the horseshoe lining and city-gate lining, the top constraint has a greater effect on the frost heaving pressures on the arch and the inverted arch. For the round lining, the influences of the top constraint on the frost heaving pressure in all linings are almost the same. The frost heaving pressure is maximum on the city-gate lining and minimal on the round lining. The largest frost heaving pressure all occur near the foot of the inverted arch for the three kinds of lining. Thus, the test data basically coincide with the observed in situ data.
基金Supported by the National Natural Science Fundation of China(No.31270674)
文摘Low-tempemture stress is a major abiotic stress influencing plant growth, economic yield and quality worldwide. Precise and reliable identification and test of plant cold resistance is a foundation for exploring low-temperature damages, cold resistance mechanism of plants, cultivating and innovating quality cold-re- sistant germplasm resources, which is rather important for woody plants because their perennial and large-sized characteristics. Generally, most researches on plant cold-resistant physiology focused on identification and utilization of cold resistance worldwide, and a few on test methods of cold resistance, but cold resistance mechanism has been less reported. Therefore, researches on methods of identifying and testing plant resistance have achieved considerable progress, accumulated much experience and formed characteristics gradually in terms of methodology. Current methods of identifying plant cold resistance include open field/outdoor culti- vation evaluation, cold and frost damage investigation, simulated cold weather, and mathematical model forecast. And the methods of testing plant cold resistance include growth condition test, frozen index investigation, electrolyte leakage, bioelectrical impedance mapping and so on. Synthesizing the methods of identifying and testing plant cold resistance should be a key matter in the present and future researches and application of plant cold resistance physiology, improvement and in- novation of the identification and test will be an important direction of the future researches. Identification and test of plant cold resistance based on genomies, meta- bonomics and proteomics should be the new trend of the researches on physiology and ecology of plant cold resistance.
文摘Gas Transmitting From West to East Project' is significant. It should ensure the welding quality and safety of pipeline. The task is very arduous to guarantee the quality of the project in the condition of long line, complex weather and geology features. In this paper, the welding cold cracking susceptibility of domestic X 70 pipeline steel adopted by the project, which is one of the most interesting questions of welding quality about petrol pipeline, was studied by means of oblique Y groove cracking test. The crack ratio of surface and section was tested under the conditions of different welding materials and preheat temperature .The thickness of plate steel was 14.7 mm and 10.3 mm . The results reveal that X 70 pipeline steel has good crack resistance. The research has important value for the construction of large scale pipeline engineering and the application of domestic X 70 pipeline steel.
基金Supported by the Yarmouk Universitythe KUSTAR–KAIST Institution Fund
文摘We study the interaction of a uniform, cold and collisional plasma with a test charged particle moving off-axis at a constant speed down a cylindrical tube with a resistive thick metallic wall. Upon matching the electromagnetic field components at all interfaces, the induced monopole electromagnetic fields in the plasma are obtained in the frequency domain. An expression for the plasma electric resistance and reactance is derived and analyzed numerically for some representative parameters. Near the plasma resonant frequency, the plasma resistance evolves with frequency like a parallel RLC resonator with peak resistance at the plasma frequency pe, while the plasma reactance can be capacitive or inductive in nature depending on the frequency under consideration.
文摘The energy efficiency design of the exterior wall in the buildings of the hot summer and cold winter zone of China should consider the heat prevention in summer and the heat insulation in winter. The self-insulation of the exterior?wall is a more feasible design to satisfy the energy efficiency of buildings in the?zone. However, the systematic research is urgently needed for the self-insulation of the exterior wall in the hot summer and cold winter zone of China. The paper tested the thermal performance of the common non-clay materials such as shale sintered hollow brick, sand autoclaved aerated concrete block, etc. by means of indoor experiments. The energy efficiency effect of the common materials was verified using dynamic calculation soft PKPM and several constitutions of exterior wall with different main bricks and insulation materials on the heat bridge were simulated, too. Besides, the tests of the thermal performance of exterior wall in real constructions were carried out to testify the practical effect of the recommended constitutions of exterior wall with different main bricks and insulation materials on the heat bridge. The conclusions are: the physical and thermal properties of the six non-clay wall material are better than the clay porous brick;the thermal performance of the non-clay brick can be improved obviously through the rational arrangement of the holes;shale sintered hollow brick after increasing the holes and rationalizing the hole arrangement and sand autoclaved aerated concrete block are recommended for buildings in the hot summer and cold winter area of China. The dynamic calculation results show that the thermal performances?of the non-clay materials are all satisfied with the energy efficiency;The heat transfer coefficient of the exterior wall with composition?③,?in which?the main wall was sand autoclaved aerated concrete block and the material on the heat bridge was sand autoclaved aerated concrete plate, is the smallest among the three recommended compositions.
