The chloride penetration resistance of cement-based grout materials was improved by nano-silica emulsion.Specimens of mixtures containing different nano-silica particles or emulsions were exposed in sodium chloride so...The chloride penetration resistance of cement-based grout materials was improved by nano-silica emulsion.Specimens of mixtures containing different nano-silica particles or emulsions were exposed in sodium chloride solutions of specific concentrations with different test ages.Hardened properties of the mixes were assessed in terms of weight loss and compressive strength.X-ray diffraction(XRD)and scanning electron microscopy(SEM)of mixes were performed to analysis the phase evolution and microstructure.The results demonstrated that the introduction of nano-SiO_(2) emulsion significantly decreased the compressive strength loss and calcium hydroxide(CH)crystal content of hydration production,and then enhanced the resistance of cement-based grouting materials to chloride ion penetration.This improvement derives from the filling and pozzolanic effects of nano-SiO_(2) particles,which were incorporated via an emulsion and attributed to a well dispersion in grouting matrix.展开更多
Grout injection is used for sealing or strengthening the ground in order to prevent water entrance or any failure after excavation.There are many methods of grouting.Permeation grouting is one of the most common types...Grout injection is used for sealing or strengthening the ground in order to prevent water entrance or any failure after excavation.There are many methods of grouting.Permeation grouting is one of the most common types in which the grout material is injected to the pore spaces of the ground.In grouting operations,the grout quality is important to achieve the best results.There are four main characteristics for a grout mixture including bleeding,setting time,strength,and viscosity.In this paper,we try to build some efficient grouting mixtures with different water to cement ratios considering these characteristics.The ingredients of grout mixtures built in this study are cement,water,bentonite,and some chemical additives such as sodium silicate,sodium carbonate,and triethanolamine(TEA).The grout mixtures are prepared for both of the sealing and strengthening purposes for a structural project.Effect of each abovementioned ingredient is profoundly investigated.Since each ingredient may have positive or negative aspect,an optimization of appropriate amount of each ingredient is determined.The optimization is based on 200 grout mixture samples with different percentages of ingredients.Finally,some of these grout mixtures are chosen for the introduced project.It should be mentioned that grouting operations depend on various factors such as pressure of injection,ground structure and grain size of soils.However,quality of a grout can be helpful to make an injection easier and reasonable.For example,during the injection,a wrong estimated setting time can destroy the injected grout by washing the grout or setting early which prevents grouting.This paper tries to show some tests in easy way to achieve a desirable sample of grout.展开更多
Main performance of the cement grouting materials made up by Portland cement（PC） and sulphoaluminate cement（SAC） was investigated in this program, a kind of expanding agent（EA） which was mainly constituted by me...Main performance of the cement grouting materials made up by Portland cement（PC） and sulphoaluminate cement（SAC） was investigated in this program, a kind of expanding agent（EA） which was mainly constituted by metakaolin and alunite was utilized for the compensation of the shrinkage, the hydration products and micro structure of the grouting materials were researched by X-ray diffraction（XRD） and scanning electron microscopy（SEM）. The results showed that a high expansion rate of the grouting materials could be reached as the expanding agent mixed in 6% of PC mass; the addition of SAC in the S2（PC：SAC：EA=34：6：2.25） brought a further improvement of the expansion rate of the grouting materials, the analysis of XRD and SEM showed that due to the reaction of expanding agent and SAC in the grouting materials, more ettringite crystal was generated, which resulted in a higher early strength, the addition of SAC played an expansion and strength reinforcement role in the grouting materials.展开更多
Fractured, very permeable rock hosting repositories for radioactive waste will require grouting. New grout types of possible use where long-term performance is needed should have a small amount of cement for minimizin...Fractured, very permeable rock hosting repositories for radioactive waste will require grouting. New grout types of possible use where long-term performance is needed should have a small amount of cement for minimizing the increase in porosity that will follow from the ultimate dissolution and erosion of this component. They have to be low-viscous and gain strength early after injection and packing theory can assist designers in selecting suitable proportions of various grout components. Optimum particle packing means that the porosity is at minimum and that the amount of cement paste needed to fill the voids between aggregate particles is very small. Low porosity and microstructural stability must be guaranteed for long periods of time. Organic additives for reaching high fluidity cannot be used since they can give off colloids that carry released radionuclides and talc can be an alternative superplasticizer. Low-pH cement reacts with talc to give high strength with time while Portland cement gives early but limited strengthening. The clay mineral palygorskite can be used for early gelation because of its thixotropic properties. Once forced into the rock fractures or channels in soil it stiffens and serves as a filter that prevents fine particles to migrate through it be lost. However, its hydrophilic potential is too high to give the grout a high density and high strength. According to the experiments carried out, most of the investigated grouts are injectable in fractures with apertures down to 100 μm.展开更多
The ongoing operation of subway systems makes existing tunnels vulnerable to deformations and structural damage caused by adjacent foundation pit construction.Such deformations-manifesting as horizontal displacement,h...The ongoing operation of subway systems makes existing tunnels vulnerable to deformations and structural damage caused by adjacent foundation pit construction.Such deformations-manifesting as horizontal displacement,heightened lateral convergence,and internal force redistribution-may significantly compromise subway operational safety.Grouting remediation has become a widely adopted solution for tunnel deformation control and structural reinforcement.Developing optimized grouting materials is crucial for improving remediation effectiveness,ensuring structural integrity,and maintaining uninterrupted subway operations.This investigation explores the substitution of fine mortar aggregates with 0.1 mm discarded rubber particles at varying concentrations(0%,3%,6%,9%,12%,and 15%).Experimental parameters included three water-cement ratios(0.65,0.70,and 0.75)with constant 4%WPU content.Mechanical properties including compressive strength,flexural strength,and compression-to-bending ratio were evaluated across specified curing periods.Material characterization employed Fourier Transform Infrared Spectroscopy(FTIR)spectroscopy for molecular analysis and Scanning Electron Microscopy(SEM)for microstructural examination.Results indicate optimal toughness at 0.70 water-cement ratio with 6%rubber content,meeting mechanical pumping specifications while maintaining structural performance.展开更多
The aim of this study is to appraise the potential of calcium sulfoaluminate(CSA)cement-based grouts in simulated permafrost environments.The hydration and performance of CSA cement-based grouts cured in cold environm...The aim of this study is to appraise the potential of calcium sulfoaluminate(CSA)cement-based grouts in simulated permafrost environments.The hydration and performance of CSA cement-based grouts cured in cold environments(10,0,and−10℃)are investigated using a combination of tests,including temperature recording,X-ray diffraction(XRD)tests,thermogravimetric analysis(TGA),and unconfined compressive strength(UCS)tests.The recorded temperature shows a rapid increase in temperature at the early stage in all the samples.Meanwhile,results of the TGA and XRD tests show the generation of a significant quantity of hydration products,which indicates the rapid hydration of CSA cement-based grouts at the early stage at low temperatures.Consequently,the CSA cement-based grouts exhibit remarkably high early strength.The UCS values of the samples cured for 2 h at−10,0,and 10℃ are 6.5,12.0,and 12.3 MPa,respectively.The UCS of the grouts cured at−10,0,and 10℃ increases continuously with age and ultimately reached 14.9,19.0,and 30.6 MPa at 28 d,respectively.The findings show that the strength of grouts fabricated using CSA cement can develop rapidly in cold environments,thus rendering them promising for permafrost applications.展开更多
The applicability of cement grout （or cement-based grout） has been considered as an alternative to bentonite grout commonly used to backfill closed-loop vertical ground heat exchangers. In a geothermal heat pump sys...The applicability of cement grout （or cement-based grout） has been considered as an alternative to bentonite grout commonly used to backfill closed-loop vertical ground heat exchangers. In a geothermal heat pump system, repeated heating-cooling cycles may cause adverse effects on the integrity of cement grout in the ground heat exchanger. To account for the temperature cycling effect, the strength degradation of cement grout due to temperature cycling has been examined by measuring the unconfined compression strength of cured specimens in a humidity-temperature controlling chamber with applying temperature cycles between -5℃ and 50℃. There is a tendency that the unconfined compression strength decreases with an increase in the number of temperature cycles. On the other hand, an equivalent hydraulic conductivity of a pipe-embedded cement grout specimen was evaluated by carrying out a modified flexible wall permeameter test equipped with a water circulating system to control temperature inside the pipe section. The applied operating temperature range was from 5 to 35℃. After three cycles of heating-cooling circulation, the equivalent hydraulic conductivity becomes asymptotic to a constant value, which implies there is no severe detachment of the pipe from the cement grout.展开更多
The study aims to investigate the carbonated water erosion mechanism of lining concrete in tunnels traversing karst environment and enhance its resistance.In this study,dynamic carbonated water erosion was simulated t...The study aims to investigate the carbonated water erosion mechanism of lining concrete in tunnels traversing karst environment and enhance its resistance.In this study,dynamic carbonated water erosion was simulated to assess erosion depth,microstructure,phase migrations,and pore structure in various tunnel lining cement-based materials.Additionally,Ca^(2+)leaching was analyzed,and impact of Ca/Si molar ratio in hydration products on erosion resistance was discussed by thermodynamic calculations.The results indicate that carbonated water erosion caused rough and porous surface on specimens,with reduced portlandite and CaCO_(3) content,increased porosity,and an enlargement of pore size.The thermodynamic calculations indicate that the erosion is spontaneous,driven by physical dissolution and chemical reactions dominated by Gibbs free energy.And the erosion reactions proceed more spontaneously and extensively when Ca/Si molar ratio in hydration products was higher.Therefore,cement-based materials with higher portlandite content exhibit weaker erosion resistance.Model-building concrete,with C-S-H gel and portlandite as primary hydration products,has greater erosion susceptibility than shotcrete with ettringite as main hydration product.Moreover,adding silicon-rich mineral admixtures can enhance the erosion resistance.This research offers theory and tech insights to boost cement-based material resistance against carbonated water erosion in karst tunnel engineering.展开更多
Chloride ions(Cl^(-))have been shown to impact the long-lasting nature of reinforced concrete.However,Cl^(-)that are already bound inside the concrete will not lead to the deterioration of the concrete’s characterist...Chloride ions(Cl^(-))have been shown to impact the long-lasting nature of reinforced concrete.However,Cl^(-)that are already bound inside the concrete will not lead to the deterioration of the concrete’s characteristics.The composition of the cement-based material,including the type of cement and auxiliary materials,greatly influences the ability of the material to bind Cl^(-),and varied components result in varying binding beha-vior of the Cl^(-).Simultaneously,the Cl^(-)binding process in concrete is influenced by both the internal and exterior surroundings,as well as the curing practices.These factors impact the hydration process of the cement and the internal pore structure of the concrete.Currently,mathematical theories and molecular dynamics simulations have increasingly been employed as the prevalent methods for examining the binding behaviors of Cl^(-)in concrete.These techniques are extensively utilized for predicting the lifespan and conducting microscopic studies of reinforced concrete in Cl^(-)settings.This work proposes recommendations for future research based on a summary of experimental and simulation investigations on Cl^(-)binding.Which will offer theoretical guidance for studying the binding of Cl^(-)in cement-based materials.展开更多
A slurry-phase carbonation technique was utilized,employing argon oxygen decarburization slag(AOD slag)as a source of calcium and MgCl_(2) as a regulator for the crystal morphology of acicular aragonite.Subsequently,t...A slurry-phase carbonation technique was utilized,employing argon oxygen decarburization slag(AOD slag)as a source of calcium and MgCl_(2) as a regulator for the crystal morphology of acicular aragonite.Subsequently,the carbonated AOD slag,enriched with acicular aragonite,was employed in fabricating composite cementitious materials,followed by an analysis of their evolution in hydration heat,hydration products,and microscopic morphology.Additionally,it delved into the mechanism through which acicular aragonite enhances the stength of composite cementitious materials.Moreover,advanced simulation software for engineering and sciences(ABAQUS)was utilized to simulate the compressive performance of composite mortar with varying dosages of acicular aragonite.The findings demonstrate that the carbonated AOD slag,containing 83.4%acicular aragonite(with an average aspect ratio of 21.31),exhibited commendable compatibility with cement.Moderate integration of carbonated AOD slag facilitated the formation of calcium sulfoaluminate hydrate(AFt)phases.The acicular aragonite within the cementitious matrix showcased remarkable filling effects.As the dosage of carbonated AOD slag increased,flexural and compressive strengths of cement mortar initially rose before declining.Upon reaching a 6%cement inclusion of carbonated AOD slag,the various constituents of the cementitious material displayed optimal synergy.The numerical simulation results confirmed the experimental findings,demonstrating a favorable increase in compressive strength and flexural strength with the addition of acicular aragonite.The acicular aragonite strengthened the matrix by serving bridging and pull-out functions.展开更多
Traditional cement-based slurries are often constrained by excessive cement consumption,prolonged setting times,and limited controllability,which hinder their broader engineering applications.To overcome these challen...Traditional cement-based slurries are often constrained by excessive cement consumption,prolonged setting times,and limited controllability,which hinder their broader engineering applications.To overcome these challenges,this study focuses on optimizing ordinary cement-based slurry through the incorporation of targeted additives and rational adjustment of mix proportions,with the aim of developing a rapid-setting,early-strength cementitious system.In particular,a series of comparative and orthogonal experiments were conducted to systematically examine the evolution of the slurry's macroscopic properties.In addition,the response surface methodology(RSM)was introduced to reveal the interaction mechanisms among key parameters,thereby establishing a quantitative foundation for the precise regulation of slurry performance.The comparative results demonstrate that silica fume significantly outperforms fly ash in enhancing both the rheological and mechanical behavior of the slurry.Regarding fluidity,the average consistency and slump of the silica fume mixture were reduced by 80 mm and 75 mm,respectively,compared with those containing fly ash,indicating more effective control of flowability.In terms of setting and strength development,the silica fume slurry exhibited a setting time up to 9.6 h shorter and a compressive strength up to 3.6 MPa higher under identical mix conditions.These results confirm the clear superiority of silica fume in promoting rapid solidification and early strength gain.展开更多
In order to realize the full resource utilization of ferronickel slag(FNS)in cement-based materials,this paper studied the influences of mechanical grinding activation on the physical and chemical properties and react...In order to realize the full resource utilization of ferronickel slag(FNS)in cement-based materials,this paper studied the influences of mechanical grinding activation on the physical and chemical properties and reactivity of ferrous extraction tailing of nickel slag(FETNS).Four grinding processes of 5,10,20 and 30 min were set up to evaluate the influence of grinding process on the physical and chemical properties of FETNS with the aid of BET,XRD,Rietveld analysis and particle size distribution.The cement-FETNS composite cementitious material was prepared by replacing cement with 0%,10%,15%,20%,25%and 30%FETNS.The influence of FETNS fineness and content on the properties of composite cementitious system were characterized by mechanical properties,reaction products,early hydration process and pore structure characteristics.The results show that the grinding process can effectively improve the pozzolanic activity of FETNS.The compressive strength of FETNS-M_(30)paste is higher than that of FETNS-M_(5) paste in the early and late stages,and the later strength is higher than that of the baseline group when the content of FETNS-M_(30)is 10%-25%.The pozzolanic activity of FETNS-M_(30)powder is significantly improved and higher than that of FETNS-M_(5) powder.Under the same content,the Ca/Si ratio of C-S-H gel in FETNS-M_(30)paste is small,and the degree of silicate polymerization is higher.When the FETNS-M_(30)content is 10%,the proportions of favorable pores d<50 nm(harmless pores and less-harmful pores)of FETNS-M_(5) paste and FETNS-M_(30)paste is 95.3%and 95.4%,respectively,indicating a denser pore structure of the FETNS-M_(30)paste.展开更多
To address the issues of short setting time and high bleeding rate of A component,which easily cause pipe plugging and poor grouting performance when a two-component grout is injected synchronously behind the Segmenta...To address the issues of short setting time and high bleeding rate of A component,which easily cause pipe plugging and poor grouting performance when a two-component grout is injected synchronously behind the Segmental Lining,the inorganic retarder sodium pyrophosphate(TSPP)and three organic retarders were added to the A component:sodium citrate(SC),sodium tartrate(ST)and glycerol(GLY).The effect law and microscopic mechanism of viscosity,bleeding rate,setting time,gelling time,compressive strength,and stone rate were investigated.The results revealed that the addition of retarders could enhance the stability and setting time of the A component and increase the gelling time,stone rate,and compressive strength of two-component grout.Among them,the performance of the grout with an SC dosage of 0.1% was superior.The bleeding rate of this grout was reduced to 3.5%,the stone rate of the two-component grout was more than 99%,and the early compressive strength and late compressive strength of this grout were increased by approximately 35% and 7%,respectively.The initial and final setting time of the A component with a TSPP dosage of 0.3% was the longest,which was prolonged to 17 and 26 h,respectively.Microscopic analysis revealed that the four retarders hindered the hydration process of cement through complexation and adsorption,and inhibited the hydration of C_(3)S and the crystallisation of CH.Moreover,they reduced the defects caused by the rapid reaction of water glass and CH on the solid phase structure,enabled the microstructure of the stone body to be denser,and subsequently,enhanced the compressive strength.展开更多
The main purpose of using geothermal energy piles(GEPs)is to enable the exploitation of geothermal energy for meeting the heating/cooling demands of buildings efficiently.However,the installation process of convention...The main purpose of using geothermal energy piles(GEPs)is to enable the exploitation of geothermal energy for meeting the heating/cooling demands of buildings efficiently.However,the installation process of conventional GEPs is inconvenient compared with that of traditional foundation piles.The pre-bored grouted planted geothermal energy pile(PGP GEP)is an innovative technology to simplify the installation process.Most investigations of in-situ experiments for conventional GEPs have focused on summer conditions.An in-situ test for a PGP GEP was conducted to analyze the temperature changes and thermo-mechanical characteristics under winter conditions.The results show that the average temperature of the pile decreased by 5.1℃,and the pile exhibited a general trend of high temperatures at both ends and low temperatures in the middle.In mechanics,strong pile end restraints resulted in smaller observed axial strain and higher axial thermal-induced force in the pile ends than at the middle of the pile.展开更多
Concrete is a continuously evolving material, and even the definition of high-performance concrete has changed over time. In this paper, high-performance characteristics of concrete material are considered to be those...Concrete is a continuously evolving material, and even the definition of high-performance concrete has changed over time. In this paper, high-performance characteristics of concrete material are considered to be those that support the desirable durability, resilience, and sustainability of civil infrastructure that directly impact our quality of life. It is proposed that high-performance material characteristics include tensile ductility, autogenous crack-width control, and material “greenness.” Furthermore, smart functionalities should be aimed at enhancing infrastructure durability, resilience, and sustainability by responding to changes in the surrounding environment of the structure in order to perform desirable functions, thus causing the material to behave in a manner more akin to certain biological materials. Based on recent advances in engineered cementitious composites (ECCs), this paper suggests that concrete embodying such high-performance characteristics and smart multifunctionalities can be designed, and holds the potential to fulfill the expected civil infrastructure needs of the 21st century. Highlights of relevant properties of ECCs are provided, and directions for necessary future research are indicated.展开更多
The electrical characteristics of cement-based material can be remarkably improved by the addition of short carbon fibers. Carbon fiber reinforced cement composite (CFRC) is an intrinsically smart material that can se...The electrical characteristics of cement-based material can be remarkably improved by the addition of short carbon fibers. Carbon fiber reinforced cement composite (CFRC) is an intrinsically smart material that can sense not only the stress and strain, but also the temperature. In this paper, variations of electrical resistivity with external applied load, and relation of thermoelectric force and temperature were investigated. Test results indicated that the electrical signal is related to the increase in the material volume resistivity during crack generation or propagation and the decrease in the resistivity during crack closure. Moreover, it was found that the fiber addition increased the linearity and reversibility of the Seebeck effect in the cement-based materials. The change of electrical characteristics reflects large amount of information of inner damage and temperature differential of composite, which can be used for stress-strain or thermal self-monitoring by embedding it in the concrete structures.展开更多
Effects of calcined coal gangue （CG） aggregates treated by the surface thermal activation on the flowability and strength, and paste-CG aggregate interfaces of the cement-based material were investigated. The experi...Effects of calcined coal gangue （CG） aggregates treated by the surface thermal activation on the flowability and strength, and paste-CG aggregate interfaces of the cement-based material were investigated. The experimental results show that the compressive and flexural strength of the cement-based material with the calcined CG aggregates is much higher than that of the material with the natural CG aggregates, but the flowability of the material with calcined CG is significantly reduced with the calcined time. The strength of the material with the calcined CG aggregates only increases little with the calcined time at the same w/c ratio, but is reduced with the calcined time at the same flowability. The CG aggregates calcined by the surface thermal activation obviously overcomes the disadvantages of fully calcined CG.展开更多
The self-healing action of a permeable crystalline coating on the po rous mortar was investigated by two times impermeability test. Moreover, the sel f-healing mechanism of cement-based materials with the permeable cr...The self-healing action of a permeable crystalline coating on the po rous mortar was investigated by two times impermeability test. Moreover, the sel f-healing mechanism of cement-based materials with the permeable crystalline c oating was studied by SEM. The results indicate that the permeable crystalline c oating not only seals the pores and cracks in mortar during its curing process, but also heals the permeable pathway caused by first impermeability test or crac ks produced by freeze-thaw cycles. Therefore, cement-based materials can be im proved by the permeable crystalline coating for the self-healing function. SEM images prove that the self-healing function is realized by generating a great q uantity of non-soluble dendritic crystalline within the pores and cracks, which prevents the penetration of water and other liquids.展开更多
The influence of water content on the conductivity and piezoresistivity of cement-based material with carbon fiber （CF） and carbon black （CB） was investigated. The piezoresistivity of cement-based material with bo...The influence of water content on the conductivity and piezoresistivity of cement-based material with carbon fiber （CF） and carbon black （CB） was investigated. The piezoresistivity of cement-based material with both CF and CB was compared with that of cement-based material with CF only, and the changes in electrical resistivity of cement-based material with both CF and CB under static and loading conditions in different drying and soaking time were studied. It is found that the piezoresistivity of cement-based material with both CF and CB has better repeatability and linearity than that of cement-based material with CF only. The conductivity and the sensitivity of piezoresistive cement-based material with both CF and CB are enhanced as the water content in piezoresistive cement-based material increases.展开更多
The effects of the component gradient distribution at interface and the fiber gradient distribution on the strength of cement-based materials were studied. The results show that the flexural strength and compressive s...The effects of the component gradient distribution at interface and the fiber gradient distribution on the strength of cement-based materials were studied. The results show that the flexural strength and compressive strength of the mortar and concrete with interface component and fiber gradient distributions are obviously improved. The strengthes of the fiber gradient distributed mortar and concrete (FGDM/C) are higher than those of fiber homogeneously distributed mortar and concrete (FHDM/C). To obtain the same strength, therefore, a smaller fiber volume content in FGDM/C is needed than that in FHDM/C. The results also show that the component gradient distribution of the concrete can be obtained by means of multi-layer vibrating formation.展开更多
基金Funded by a Science and Technology Project from the Ministry of Housing and Urban-Rural Development of the People’s Republic of China(No.2019-K-047)Yangzhou Government-Yangzhou University Cooperative Platform Project for Science and Technology Innovation(No.YZ2020262)。
文摘The chloride penetration resistance of cement-based grout materials was improved by nano-silica emulsion.Specimens of mixtures containing different nano-silica particles or emulsions were exposed in sodium chloride solutions of specific concentrations with different test ages.Hardened properties of the mixes were assessed in terms of weight loss and compressive strength.X-ray diffraction(XRD)and scanning electron microscopy(SEM)of mixes were performed to analysis the phase evolution and microstructure.The results demonstrated that the introduction of nano-SiO_(2) emulsion significantly decreased the compressive strength loss and calcium hydroxide(CH)crystal content of hydration production,and then enhanced the resistance of cement-based grouting materials to chloride ion penetration.This improvement derives from the filling and pozzolanic effects of nano-SiO_(2) particles,which were incorporated via an emulsion and attributed to a well dispersion in grouting matrix.
文摘Grout injection is used for sealing or strengthening the ground in order to prevent water entrance or any failure after excavation.There are many methods of grouting.Permeation grouting is one of the most common types in which the grout material is injected to the pore spaces of the ground.In grouting operations,the grout quality is important to achieve the best results.There are four main characteristics for a grout mixture including bleeding,setting time,strength,and viscosity.In this paper,we try to build some efficient grouting mixtures with different water to cement ratios considering these characteristics.The ingredients of grout mixtures built in this study are cement,water,bentonite,and some chemical additives such as sodium silicate,sodium carbonate,and triethanolamine(TEA).The grout mixtures are prepared for both of the sealing and strengthening purposes for a structural project.Effect of each abovementioned ingredient is profoundly investigated.Since each ingredient may have positive or negative aspect,an optimization of appropriate amount of each ingredient is determined.The optimization is based on 200 grout mixture samples with different percentages of ingredients.Finally,some of these grout mixtures are chosen for the introduced project.It should be mentioned that grouting operations depend on various factors such as pressure of injection,ground structure and grain size of soils.However,quality of a grout can be helpful to make an injection easier and reasonable.For example,during the injection,a wrong estimated setting time can destroy the injected grout by washing the grout or setting early which prevents grouting.This paper tries to show some tests in easy way to achieve a desirable sample of grout.
基金Funded by the National Key Technology R&D Program in the12th Five Year Plan of China(No.2011BAE14B06)the National High Technology ResearchDevelopment Program of China(No.2015AA034701)
文摘Main performance of the cement grouting materials made up by Portland cement（PC） and sulphoaluminate cement（SAC） was investigated in this program, a kind of expanding agent（EA） which was mainly constituted by metakaolin and alunite was utilized for the compensation of the shrinkage, the hydration products and micro structure of the grouting materials were researched by X-ray diffraction（XRD） and scanning electron microscopy（SEM）. The results showed that a high expansion rate of the grouting materials could be reached as the expanding agent mixed in 6% of PC mass; the addition of SAC in the S2（PC：SAC：EA=34：6：2.25） brought a further improvement of the expansion rate of the grouting materials, the analysis of XRD and SEM showed that due to the reaction of expanding agent and SAC in the grouting materials, more ettringite crystal was generated, which resulted in a higher early strength, the addition of SAC played an expansion and strength reinforcement role in the grouting materials.
文摘Fractured, very permeable rock hosting repositories for radioactive waste will require grouting. New grout types of possible use where long-term performance is needed should have a small amount of cement for minimizing the increase in porosity that will follow from the ultimate dissolution and erosion of this component. They have to be low-viscous and gain strength early after injection and packing theory can assist designers in selecting suitable proportions of various grout components. Optimum particle packing means that the porosity is at minimum and that the amount of cement paste needed to fill the voids between aggregate particles is very small. Low porosity and microstructural stability must be guaranteed for long periods of time. Organic additives for reaching high fluidity cannot be used since they can give off colloids that carry released radionuclides and talc can be an alternative superplasticizer. Low-pH cement reacts with talc to give high strength with time while Portland cement gives early but limited strengthening. The clay mineral palygorskite can be used for early gelation because of its thixotropic properties. Once forced into the rock fractures or channels in soil it stiffens and serves as a filter that prevents fine particles to migrate through it be lost. However, its hydrophilic potential is too high to give the grout a high density and high strength. According to the experiments carried out, most of the investigated grouts are injectable in fractures with apertures down to 100 μm.
基金supported by the National Natural Science Foundation of China,Grant Nos.42477185,41602308the Zhejiang Provincial Natural Science Foundation of China,Grant No.LY20E080005+2 种基金the Zhejiang Province University Students Science and Technology Innovation Program,Grant No.0201310P28the PostGraduate Course Construction Project of Zhejiang University of Science and Technology,Grant No.2021yjskj05the Zhejiang University of Science and Technology Graduate Research and Innovation Fund,Grant No.2023yjskc10.
文摘The ongoing operation of subway systems makes existing tunnels vulnerable to deformations and structural damage caused by adjacent foundation pit construction.Such deformations-manifesting as horizontal displacement,heightened lateral convergence,and internal force redistribution-may significantly compromise subway operational safety.Grouting remediation has become a widely adopted solution for tunnel deformation control and structural reinforcement.Developing optimized grouting materials is crucial for improving remediation effectiveness,ensuring structural integrity,and maintaining uninterrupted subway operations.This investigation explores the substitution of fine mortar aggregates with 0.1 mm discarded rubber particles at varying concentrations(0%,3%,6%,9%,12%,and 15%).Experimental parameters included three water-cement ratios(0.65,0.70,and 0.75)with constant 4%WPU content.Mechanical properties including compressive strength,flexural strength,and compression-to-bending ratio were evaluated across specified curing periods.Material characterization employed Fourier Transform Infrared Spectroscopy(FTIR)spectroscopy for molecular analysis and Scanning Electron Microscopy(SEM)for microstructural examination.Results indicate optimal toughness at 0.70 water-cement ratio with 6%rubber content,meeting mechanical pumping specifications while maintaining structural performance.
基金This study was supported by a research project(RES0049413)at the University of Alberta.The first author is grateful for the scholarship provided by the China Scholarship Council。
文摘The aim of this study is to appraise the potential of calcium sulfoaluminate(CSA)cement-based grouts in simulated permafrost environments.The hydration and performance of CSA cement-based grouts cured in cold environments(10,0,and−10℃)are investigated using a combination of tests,including temperature recording,X-ray diffraction(XRD)tests,thermogravimetric analysis(TGA),and unconfined compressive strength(UCS)tests.The recorded temperature shows a rapid increase in temperature at the early stage in all the samples.Meanwhile,results of the TGA and XRD tests show the generation of a significant quantity of hydration products,which indicates the rapid hydration of CSA cement-based grouts at the early stage at low temperatures.Consequently,the CSA cement-based grouts exhibit remarkably high early strength.The UCS values of the samples cured for 2 h at−10,0,and 10℃ are 6.5,12.0,and 12.3 MPa,respectively.The UCS of the grouts cured at−10,0,and 10℃ increases continuously with age and ultimately reached 14.9,19.0,and 30.6 MPa at 28 d,respectively.The findings show that the strength of grouts fabricated using CSA cement can develop rapidly in cold environments,thus rendering them promising for permafrost applications.
基金supported by the Fundamental Research and Development Program of the Center of New and Renewable Energy of the Ministry of Knowledge and Economy (Grant No. 2008-N-GE08-R-01)the National Research Foundation of Korea Grant funded by the Korean Government (Grant No. 2010-0011159)
文摘The applicability of cement grout （or cement-based grout） has been considered as an alternative to bentonite grout commonly used to backfill closed-loop vertical ground heat exchangers. In a geothermal heat pump system, repeated heating-cooling cycles may cause adverse effects on the integrity of cement grout in the ground heat exchanger. To account for the temperature cycling effect, the strength degradation of cement grout due to temperature cycling has been examined by measuring the unconfined compression strength of cured specimens in a humidity-temperature controlling chamber with applying temperature cycles between -5℃ and 50℃. There is a tendency that the unconfined compression strength decreases with an increase in the number of temperature cycles. On the other hand, an equivalent hydraulic conductivity of a pipe-embedded cement grout specimen was evaluated by carrying out a modified flexible wall permeameter test equipped with a water circulating system to control temperature inside the pipe section. The applied operating temperature range was from 5 to 35℃. After three cycles of heating-cooling circulation, the equivalent hydraulic conductivity becomes asymptotic to a constant value, which implies there is no severe detachment of the pipe from the cement grout.
基金Project(2021YJ059)supported by the Research Project of China Academy of Railway Sciences。
文摘The study aims to investigate the carbonated water erosion mechanism of lining concrete in tunnels traversing karst environment and enhance its resistance.In this study,dynamic carbonated water erosion was simulated to assess erosion depth,microstructure,phase migrations,and pore structure in various tunnel lining cement-based materials.Additionally,Ca^(2+)leaching was analyzed,and impact of Ca/Si molar ratio in hydration products on erosion resistance was discussed by thermodynamic calculations.The results indicate that carbonated water erosion caused rough and porous surface on specimens,with reduced portlandite and CaCO_(3) content,increased porosity,and an enlargement of pore size.The thermodynamic calculations indicate that the erosion is spontaneous,driven by physical dissolution and chemical reactions dominated by Gibbs free energy.And the erosion reactions proceed more spontaneously and extensively when Ca/Si molar ratio in hydration products was higher.Therefore,cement-based materials with higher portlandite content exhibit weaker erosion resistance.Model-building concrete,with C-S-H gel and portlandite as primary hydration products,has greater erosion susceptibility than shotcrete with ettringite as main hydration product.Moreover,adding silicon-rich mineral admixtures can enhance the erosion resistance.This research offers theory and tech insights to boost cement-based material resistance against carbonated water erosion in karst tunnel engineering.
文摘Chloride ions(Cl^(-))have been shown to impact the long-lasting nature of reinforced concrete.However,Cl^(-)that are already bound inside the concrete will not lead to the deterioration of the concrete’s characteristics.The composition of the cement-based material,including the type of cement and auxiliary materials,greatly influences the ability of the material to bind Cl^(-),and varied components result in varying binding beha-vior of the Cl^(-).Simultaneously,the Cl^(-)binding process in concrete is influenced by both the internal and exterior surroundings,as well as the curing practices.These factors impact the hydration process of the cement and the internal pore structure of the concrete.Currently,mathematical theories and molecular dynamics simulations have increasingly been employed as the prevalent methods for examining the binding behaviors of Cl^(-)in concrete.These techniques are extensively utilized for predicting the lifespan and conducting microscopic studies of reinforced concrete in Cl^(-)settings.This work proposes recommendations for future research based on a summary of experimental and simulation investigations on Cl^(-)binding.Which will offer theoretical guidance for studying the binding of Cl^(-)in cement-based materials.
基金the financial support from Innovative Research Group Project of Natural Science Foundation of Hebei Province(No.E2022209093)Central Guidance Local Science and Technology Development Fund Project of Hebei Province(No.236Z3803G)+1 种基金Scientific and Technological Project of Tangshan(No.23130205E)Youth Teacher Pre Research Fund Project of the School of Metallurgy and Energy(No.YJY20244373).
文摘A slurry-phase carbonation technique was utilized,employing argon oxygen decarburization slag(AOD slag)as a source of calcium and MgCl_(2) as a regulator for the crystal morphology of acicular aragonite.Subsequently,the carbonated AOD slag,enriched with acicular aragonite,was employed in fabricating composite cementitious materials,followed by an analysis of their evolution in hydration heat,hydration products,and microscopic morphology.Additionally,it delved into the mechanism through which acicular aragonite enhances the stength of composite cementitious materials.Moreover,advanced simulation software for engineering and sciences(ABAQUS)was utilized to simulate the compressive performance of composite mortar with varying dosages of acicular aragonite.The findings demonstrate that the carbonated AOD slag,containing 83.4%acicular aragonite(with an average aspect ratio of 21.31),exhibited commendable compatibility with cement.Moderate integration of carbonated AOD slag facilitated the formation of calcium sulfoaluminate hydrate(AFt)phases.The acicular aragonite within the cementitious matrix showcased remarkable filling effects.As the dosage of carbonated AOD slag increased,flexural and compressive strengths of cement mortar initially rose before declining.Upon reaching a 6%cement inclusion of carbonated AOD slag,the various constituents of the cementitious material displayed optimal synergy.The numerical simulation results confirmed the experimental findings,demonstrating a favorable increase in compressive strength and flexural strength with the addition of acicular aragonite.The acicular aragonite strengthened the matrix by serving bridging and pull-out functions.
基金the National Natural Science Foundation of China(52278403).
文摘Traditional cement-based slurries are often constrained by excessive cement consumption,prolonged setting times,and limited controllability,which hinder their broader engineering applications.To overcome these challenges,this study focuses on optimizing ordinary cement-based slurry through the incorporation of targeted additives and rational adjustment of mix proportions,with the aim of developing a rapid-setting,early-strength cementitious system.In particular,a series of comparative and orthogonal experiments were conducted to systematically examine the evolution of the slurry's macroscopic properties.In addition,the response surface methodology(RSM)was introduced to reveal the interaction mechanisms among key parameters,thereby establishing a quantitative foundation for the precise regulation of slurry performance.The comparative results demonstrate that silica fume significantly outperforms fly ash in enhancing both the rheological and mechanical behavior of the slurry.Regarding fluidity,the average consistency and slump of the silica fume mixture were reduced by 80 mm and 75 mm,respectively,compared with those containing fly ash,indicating more effective control of flowability.In terms of setting and strength development,the silica fume slurry exhibited a setting time up to 9.6 h shorter and a compressive strength up to 3.6 MPa higher under identical mix conditions.These results confirm the clear superiority of silica fume in promoting rapid solidification and early strength gain.
基金Funded by the Science and Technology Program of Gansu Province(Nos.25CXGA070,24JRRA213)the National Natural Science Foundation of China(Nos.52468036,52178216,U21A20150)。
文摘In order to realize the full resource utilization of ferronickel slag(FNS)in cement-based materials,this paper studied the influences of mechanical grinding activation on the physical and chemical properties and reactivity of ferrous extraction tailing of nickel slag(FETNS).Four grinding processes of 5,10,20 and 30 min were set up to evaluate the influence of grinding process on the physical and chemical properties of FETNS with the aid of BET,XRD,Rietveld analysis and particle size distribution.The cement-FETNS composite cementitious material was prepared by replacing cement with 0%,10%,15%,20%,25%and 30%FETNS.The influence of FETNS fineness and content on the properties of composite cementitious system were characterized by mechanical properties,reaction products,early hydration process and pore structure characteristics.The results show that the grinding process can effectively improve the pozzolanic activity of FETNS.The compressive strength of FETNS-M_(30)paste is higher than that of FETNS-M_(5) paste in the early and late stages,and the later strength is higher than that of the baseline group when the content of FETNS-M_(30)is 10%-25%.The pozzolanic activity of FETNS-M_(30)powder is significantly improved and higher than that of FETNS-M_(5) powder.Under the same content,the Ca/Si ratio of C-S-H gel in FETNS-M_(30)paste is small,and the degree of silicate polymerization is higher.When the FETNS-M_(30)content is 10%,the proportions of favorable pores d<50 nm(harmless pores and less-harmful pores)of FETNS-M_(5) paste and FETNS-M_(30)paste is 95.3%and 95.4%,respectively,indicating a denser pore structure of the FETNS-M_(30)paste.
基金Funded by the National Natural Science Foundation of China(No.52378394)the Fundamental Research Funds for the Central Universities(No.B230201037)。
文摘To address the issues of short setting time and high bleeding rate of A component,which easily cause pipe plugging and poor grouting performance when a two-component grout is injected synchronously behind the Segmental Lining,the inorganic retarder sodium pyrophosphate(TSPP)and three organic retarders were added to the A component:sodium citrate(SC),sodium tartrate(ST)and glycerol(GLY).The effect law and microscopic mechanism of viscosity,bleeding rate,setting time,gelling time,compressive strength,and stone rate were investigated.The results revealed that the addition of retarders could enhance the stability and setting time of the A component and increase the gelling time,stone rate,and compressive strength of two-component grout.Among them,the performance of the grout with an SC dosage of 0.1% was superior.The bleeding rate of this grout was reduced to 3.5%,the stone rate of the two-component grout was more than 99%,and the early compressive strength and late compressive strength of this grout were increased by approximately 35% and 7%,respectively.The initial and final setting time of the A component with a TSPP dosage of 0.3% was the longest,which was prolonged to 17 and 26 h,respectively.Microscopic analysis revealed that the four retarders hindered the hydration process of cement through complexation and adsorption,and inhibited the hydration of C_(3)S and the crystallisation of CH.Moreover,they reduced the defects caused by the rapid reaction of water glass and CH on the solid phase structure,enabled the microstructure of the stone body to be denser,and subsequently,enhanced the compressive strength.
文摘The main purpose of using geothermal energy piles(GEPs)is to enable the exploitation of geothermal energy for meeting the heating/cooling demands of buildings efficiently.However,the installation process of conventional GEPs is inconvenient compared with that of traditional foundation piles.The pre-bored grouted planted geothermal energy pile(PGP GEP)is an innovative technology to simplify the installation process.Most investigations of in-situ experiments for conventional GEPs have focused on summer conditions.An in-situ test for a PGP GEP was conducted to analyze the temperature changes and thermo-mechanical characteristics under winter conditions.The results show that the average temperature of the pile decreased by 5.1℃,and the pile exhibited a general trend of high temperatures at both ends and low temperatures in the middle.In mechanics,strong pile end restraints resulted in smaller observed axial strain and higher axial thermal-induced force in the pile ends than at the middle of the pile.
基金supported by a grant from the CMMI program at the United States National Science Foundation(1634694).
文摘Concrete is a continuously evolving material, and even the definition of high-performance concrete has changed over time. In this paper, high-performance characteristics of concrete material are considered to be those that support the desirable durability, resilience, and sustainability of civil infrastructure that directly impact our quality of life. It is proposed that high-performance material characteristics include tensile ductility, autogenous crack-width control, and material “greenness.” Furthermore, smart functionalities should be aimed at enhancing infrastructure durability, resilience, and sustainability by responding to changes in the surrounding environment of the structure in order to perform desirable functions, thus causing the material to behave in a manner more akin to certain biological materials. Based on recent advances in engineered cementitious composites (ECCs), this paper suggests that concrete embodying such high-performance characteristics and smart multifunctionalities can be designed, and holds the potential to fulfill the expected civil infrastructure needs of the 21st century. Highlights of relevant properties of ECCs are provided, and directions for necessary future research are indicated.
基金This work was supported by NSFC(No.59908007)a foundation for phosphor plan from the Science and Technology Committee of Shanghai Municipality(No.01QE14052)The financial support from the Foundation for the University Key Studies of Shanghai was also gratefully acknowledged.
文摘The electrical characteristics of cement-based material can be remarkably improved by the addition of short carbon fibers. Carbon fiber reinforced cement composite (CFRC) is an intrinsically smart material that can sense not only the stress and strain, but also the temperature. In this paper, variations of electrical resistivity with external applied load, and relation of thermoelectric force and temperature were investigated. Test results indicated that the electrical signal is related to the increase in the material volume resistivity during crack generation or propagation and the decrease in the resistivity during crack closure. Moreover, it was found that the fiber addition increased the linearity and reversibility of the Seebeck effect in the cement-based materials. The change of electrical characteristics reflects large amount of information of inner damage and temperature differential of composite, which can be used for stress-strain or thermal self-monitoring by embedding it in the concrete structures.
基金Funded by the Major State Basic Research Development Program of China('973'Project,2001CB610705)
文摘Effects of calcined coal gangue （CG） aggregates treated by the surface thermal activation on the flowability and strength, and paste-CG aggregate interfaces of the cement-based material were investigated. The experimental results show that the compressive and flexural strength of the cement-based material with the calcined CG aggregates is much higher than that of the material with the natural CG aggregates, but the flowability of the material with calcined CG is significantly reduced with the calcined time. The strength of the material with the calcined CG aggregates only increases little with the calcined time at the same w/c ratio, but is reduced with the calcined time at the same flowability. The CG aggregates calcined by the surface thermal activation obviously overcomes the disadvantages of fully calcined CG.
基金Funded by the Scientific and Technological Project of Hubei Province(2004BCS005)
文摘The self-healing action of a permeable crystalline coating on the po rous mortar was investigated by two times impermeability test. Moreover, the sel f-healing mechanism of cement-based materials with the permeable crystalline c oating was studied by SEM. The results indicate that the permeable crystalline c oating not only seals the pores and cracks in mortar during its curing process, but also heals the permeable pathway caused by first impermeability test or crac ks produced by freeze-thaw cycles. Therefore, cement-based materials can be im proved by the permeable crystalline coating for the self-healing function. SEM images prove that the self-healing function is realized by generating a great q uantity of non-soluble dendritic crystalline within the pores and cracks, which prevents the penetration of water and other liquids.
基金Funded by the National Natural Science Foundation of China (No.50238040, 50538020)the Postdoctoral Science Foundation of China (No.20060390803)the High-Tech Research and Development Program of China (No. 2002AA335010)
文摘The influence of water content on the conductivity and piezoresistivity of cement-based material with carbon fiber （CF） and carbon black （CB） was investigated. The piezoresistivity of cement-based material with both CF and CB was compared with that of cement-based material with CF only, and the changes in electrical resistivity of cement-based material with both CF and CB under static and loading conditions in different drying and soaking time were studied. It is found that the piezoresistivity of cement-based material with both CF and CB has better repeatability and linearity than that of cement-based material with CF only. The conductivity and the sensitivity of piezoresistive cement-based material with both CF and CB are enhanced as the water content in piezoresistive cement-based material increases.
文摘The effects of the component gradient distribution at interface and the fiber gradient distribution on the strength of cement-based materials were studied. The results show that the flexural strength and compressive strength of the mortar and concrete with interface component and fiber gradient distributions are obviously improved. The strengthes of the fiber gradient distributed mortar and concrete (FGDM/C) are higher than those of fiber homogeneously distributed mortar and concrete (FHDM/C). To obtain the same strength, therefore, a smaller fiber volume content in FGDM/C is needed than that in FHDM/C. The results also show that the component gradient distribution of the concrete can be obtained by means of multi-layer vibrating formation.
