The influence of different surface coatings of NiTi shape memory allays was examined using in vitro testing methods. Plates of superelastic nickel-titanium shape memory allay （ NiTi ） were coated with calcium phosph...The influence of different surface coatings of NiTi shape memory allays was examined using in vitro testing methods. Plates of superelastic nickel-titanium shape memory allay （ NiTi ） were coated with calcium phosphates （ hydroxyapatite ） by high-temperature plasma-spraying or by dip-coating. The biocompatibility was tested in vitro by cultivation of isolated human granulocytes and whole blood cells. As substrates, pure NiTi, plasma-spray-coated NiTi and dip-coated NiTi were used. Isolated granulocytes showed an increased adhesion to both calcium phosphate-coated NiTi samples. Compared to non-coated NiTi or dip-coated NiTi, the number of dead granulocytes adherent to plasma-sprayed surfaces was significantly increased （ p 〈 0.01 ）. Whether the d/f- ferences in apoptosis of granulocytes on dip-coated vs plasma-sprayed coatings observed are due to differences in material surface morphologies has to be analyzed in further studies. Because of the cellular interactions with the coating layers, h is likely that the results obtained are not caused by the underlying NiTi but due to the coating itself.展开更多
Out of the wide range of calcium phosphate(CaP)biomaterials,calcium phosphate bone cements(CPCs)have attracted increased attention since their discovery in the 1980s due to their valuable properties such as bioactivit...Out of the wide range of calcium phosphate(CaP)biomaterials,calcium phosphate bone cements(CPCs)have attracted increased attention since their discovery in the 1980s due to their valuable properties such as bioactivity,osteoconductivity,injectability,hardening ability through a low-temperature setting reaction and moldability.Thereafter numerous researches have been performed to enhance the properties of CPCs.Nonetheless,low mechanical performance of CPCs limits their clinical application in load bearing regions of bone.Also,the in vivo resorption and replacement of CPC with new bone tissue is still controversial,thus further improvements of high clinical importance are required.Bioactive glasses(BGs)are biocompatible and able to bond to bone,stimulating new bone growth while dissolving over time.In the last decades extensive research has been performed analyzing the role of BGs in combination with different CaPs.Thus,the focal point of this review paper is to summarize the available research data on how injectable CPC properties could be improved or affected by the addition of BG as a secondary powder phase.It was found that despite the variances of setting time and compressive strength results,desirable injectable properties of bone cements can be achieved by the inclusion of BGs into CPCs.The published data also revealed that the degradation rate of CPCs is significantly improved by BG addition.Moreover,the presence of BG in CPCs improves the in vitro osteogenic differentiation and cell response as well as the tissue-material interaction in vivo.展开更多
Calcium phosphates are a family of compounds with different chemical compositions, structures and properties containing calcium ions and functional groups of orthophosphate （ pO34- ）, metaphosphate （ PO3- ） or pyr...Calcium phosphates are a family of compounds with different chemical compositions, structures and properties containing calcium ions and functional groups of orthophosphate （ pO34- ）, metaphosphate （ PO3- ） or pyrophosphate （ P2O4-7 ） and sometimes hydrogen or hydroxide ions. Calcium phosphates can be widely found in nature as well as in hard tissues （bone and tooth） of the vertebrate. Owing to similar chemical composition and structure to the main inorganic constituents of bone and tooth, calcium phosphate-based materials are promising biomaterials with high biocompatibility, and have been investigated for applications in various biomedical areas. Calcium silicate-based materials have attracted much attention on their potential applications in various biomedical fields such as bone de- fect repair and drug delivery. In recent years, this research group has been focusing on the research in this exciting and rapidly evolving research field, and has published many papers. This article will provide a brief review on our main research work on the synthesis, characterization, properties and applications of nanostructured materials of calcium phosphates and calcium silicates. Finally, future perspectives and challenges for the research and applica- tions of nanostructured materials of calcium phosphates and calcium silicates are discussed.展开更多
Due to the similar chemical properties to the inorganic component in calcified tissues,synthetic calcium phosphate has been considered as ideal biomaterials with excellent biocompatibility.Nanostructured calcium phosp...Due to the similar chemical properties to the inorganic component in calcified tissues,synthetic calcium phosphate has been considered as ideal biomaterials with excellent biocompatibility.Nanostructured calcium phosphate materials play an important role in the formation of hard tissues in nature.It is reported that calcium phosphates materials in nano-size can mimic the dimensions of constituent components of calcified tissues.Recently,the synthesis and application of nanostructured calcium phosphate materials have become a very hot field.Lots of methods have been reported to prepare nanostructured calcium phosphate,and various morphologies including nanoparticles,plate-like nanocrystals,nano-needles,whiskers/fibres/wires,mesoporous,nanotubes,nano-blades,and powders with three-dimensional(3-D)structures have been obtained.More studies of nanostructured calcium phosphates are expected in biomedical area,such as tissue engineering scaffolds,drug/gene delivery systems and multifunctional systems.In this article,the synthesis and application of nanostructured calcium phosphates are reviewed and discussed.展开更多
Guided bone regeneration in the alveolar bone relies on the colonization and differentiation of immune cells within the defect area.The absence of osteoinductive and osteoimmune properties of currently available scaff...Guided bone regeneration in the alveolar bone relies on the colonization and differentiation of immune cells within the defect area.The absence of osteoinductive and osteoimmune properties of currently available scaffolds hinders to achieve optimal repair outcomes in clinical settings.Thus,we aimed to enhance the bone repair ability of polycaprolactone(PCL)scaffolds by incorporating osteoinductive amorphous calcium phosphate(ACP)with immune-regulating zinc ions(ACP(Zn),ACZP),to create a favorable immunomodulatory microenvironment.After one day of co-culture with PCL-ACZP,the spreading area of macrophage cells was significantly higher than that from the original PCL scaffold.Additionally,over 32.1%of macrophages exhibited M2 polarization within three days of co-culture.The PCLACZP/macrophage-conditioned medium significantly boosted osteogenic gene expression in MC3T3-E1 cells.After eight weeks of implantation in a rat femoral condyle defect,the BV/TV from the PCL-ACZP group reached 32.9%,1.4 times of that from the PCL group.Furthermore,the PCL-ACZP-GelMA biphasic module as prepared successfully achieved complete regeneration of three-walled alveolar bone defects in rabbits,resulting in arch-shaped alveolar bone repair and providing greater convenience in the clinical settings.This study showcased the effectiveness of PCL-ACZP-GelMA biphasic module as bioactive scaffolds in the morphological restoration of alveolar bone.展开更多
Bio-mediated soil improvement methods keep on gaining the attention of geotechnical engineers and researchers globally due to their nature-based elegance and eco-friendliness.Most prevalent bio-mediated soil improveme...Bio-mediated soil improvement methods keep on gaining the attention of geotechnical engineers and researchers globally due to their nature-based elegance and eco-friendliness.Most prevalent bio-mediated soil improvement methods include microbially induced carbonate precipitation(MICP)and enzyme-induced carbonate precipitation(EICP).During their processes,the bacteria/free urease hydrolyzes the urea into ammonium and carbonic acid,which is accompanied by a considerable increase of alkalinity(about pH 9.0).The major problem associated with the above techniques is the release of gaseous ammonia that is extremely detrimental.Therefore,this study aims to propose a new sustainable approach involving lactic acid bacteria to facilitate the calcium phosphate mineralization for the strengthening of sand matrix.The major objectives of this investigation are:(i)to evaluate the urease activity of the lactic acid bacteria under different temperatures,pH conditions and additions of metal ions,(ii)to assess the treated sand matrix,(iii)to perform cost analysis.The outcomes indicated that Limosilactobacillus sp.could effectively facilitate the urea hydrolysis,hence increasing the pH from acidic to neutral and providing a desirable environment for the calcium phosphate to mineralize within the voids of the sand.The addition of 0.01%Ni^(2+)in culture media was found to enhance the urease activity by 38.8%and compressive strength over 40%.A combined formation of amorphous-and whisker-like precipitates could bridge a larger area at particle-particle contact points,thereby faciliating a strong force-network in sand matrix.The mineralized calcium phosphate compound was found to be brushite.The cost herein for producing 1 L treatment solution was estimated to be about 2.5-folds and 11.8-folds lower compared to that of MICP and EICP treatment solutions,respectively.Moreover,since the treatment pH could potentially be regulated between acidic-neural range,it would greatly control the release of gaseous ammonia.With several environmental and economical benefits,the study has disclosed a new sustainable direction for sand improvement via the use of lactic acid bacteria.展开更多
The possible application of magnesium(Mg)in glaucoma surgical treatment has been investigated in our previous work.In this paper,the degradation behavior and biocompatibility of Mg coated with hydroxyapatite(HA)and di...The possible application of magnesium(Mg)in glaucoma surgical treatment has been investigated in our previous work.In this paper,the degradation behavior and biocompatibility of Mg coated with hydroxyapatite(HA)and dicalcium phosphate dihydrate(DCPD)in eye environment were evaluated,and uncoated Mg was used for comparison.It was found that uniform corrosion occurred macroscopically to the coated Mg samples in sodium lactate ringer’s injection(SLRI)as well as in the rabbit eyes.In micro-scale,the corrosion was characterized by local cracking and pitting primarily.Mg and calcium(Ca)were incorporated into the surface corrosion products and a multi-layer structure was formed.Compared to other samples,HA-coated Mg slowed down dramatically the alkalinity of the solution and the ion release of the sample,and exhibited the lowest corrosion rate in SLRI,which was about 0.22 mm/a.In terms of biocompatibility,fibroblasts demonstrated high viability in the HA-coated and DCPD-coated Mg groups(p<0.05)in vitro.In vivo,HA-coated Mg was found to show lower inflammatory response and fibrosis than the other groups did,as indicated by hematoxylin-eosin and immunofluorescence staining.During the degrading process of HA-coated Mg in the rabbits’eyes,no inflammation was found in the anterior chamber,lens,and vitreous body.HA-coated Mg was fully biodegraded fifteen weeks post-operation,and the scleral drainage channel(SDC)was formed without obvious scarring.It is concluded that HA-coated Mg implantation is a promising adjunctive procedure to improve the success rate of trabeculectomy.Statement of significance:Magnesium(Mg)has shown to be a potential biomaterial for ophthalmic implants in our previous work.However,inflammatory response resulted from the low corrosion resistance of Mg is a major concern.It is shown here that Mg coated with different calcium phosphates can improve these properties in varying degrees and keep the scleral drainage channel unobstructed and unscarred.Based on our in vitro and in vivo studies,HA-coated Mg exhibited a better degradation behavior and excellent biocompatibility.The scleral drainage channel still exists and aqueous humor flows out smoothly after the full degradation of the implant.It is concluded that HA-coated Mg is a promising biomaterial to increase the therapeutic efficiency of trabeculectomy for glaucoma.展开更多
Zinc calcium phosphate （Zn-Ca-P） coating and cerium-doped zinc calcium phosphate （Zn-Ca-Ce-P） coating were prepared on AZ31 magnesium alloy. The chemical compositions, morphologies and corrosion resistance of coat...Zinc calcium phosphate （Zn-Ca-P） coating and cerium-doped zinc calcium phosphate （Zn-Ca-Ce-P） coating were prepared on AZ31 magnesium alloy. The chemical compositions, morphologies and corrosion resistance of coatings were investigated through energy-dispersive X-ray spectroscopy （EDS）, X-ray photoelectron spectroscopy （XPS）, X-ray diffraction （XRD）, electron probe micro-analysis （EPMA） and scanning electron microscopy （SEM） together with hydrogen volumetric and electrochemical tests. The results indicate that both coatings predominately contain crystalline hopeite （Zn3（PO4）2·4H2O）, Mg3（PO4）2 and Ca3（PO4）2, and traces of non-crystalline MgF2 and CaF2. The Zn-Ca-Ce-P coating is more compact than the Zn-Ca-P coating due to the formation of CePO4, and displays better corrosion resistance than the Zn-Ca-P coating. Both coatings protect the AZ31 Mg substrate only during an initial immersion period. The micro-galvanic corrosion between the coatings and their substrates leads to an increase of hydrogen evolution rate （HER） with extending the immersion time. The addition of Ce promotes the homogenous distribution of Ca and formation of hopeite. The Zn-Ca-Ce-P coating has the potential for the primer coating on magnesium alloys.展开更多
Stones in the seminal vesicles are extremely rare. We present a 62-year-old patient with a stone within a seminal vesicle cyst, who was cured by laparoscopic treatment. The operative time was 80 rnin, and the estimate...Stones in the seminal vesicles are extremely rare. We present a 62-year-old patient with a stone within a seminal vesicle cyst, who was cured by laparoscopic treatment. The operative time was 80 rnin, and the estimated blood loss was 90 mL. Scanning electron microscope examination of the stone showed a compact crystal image externally and sparse spherical crystal structure in kernel. Composition of the stone was calcium fluorophosphate on X-ray diffractometer. The follow-up time was 15 months with no recurrence of cyst or stone. To our knowledge, this case is the first to describe laparoscopic removal of a stone within a seminal vesicle cyst, and the first to describe calcium fluorophosphate as the composition of seminal vesicle stones. （Asian JAndro12008 Mar; 10： 337-340）展开更多
Current calcium phosphate （ CaP ） biomaterials for bone repair, substitution, augmentation and regeneration include hydroxyapatite （ HA ） from synthetic or biologic origin, beta-tricaicium phosphate （ β- TCP ）,...Current calcium phosphate （ CaP ） biomaterials for bone repair, substitution, augmentation and regeneration include hydroxyapatite （ HA ） from synthetic or biologic origin, beta-tricaicium phosphate （ β- TCP ）, biphasic calcium phosphate （BCP）, and are available as granules, porous blocks, components of compashes （CaP/pollymer） cements, and as coatings on orthopedic and dental implants. Experimental calcium phosphate biomaterials include CO3^- and F-substituted apatites, Mg-and Zn-substituted β-TCP, calcium phosphate glasses, This paper is a brief review of the different types of CaP biomaterials and their properties such as bioactivity , osteoconductivity , osteoinductivity.展开更多
The present study reports on the growth of calcium phosphate coatings on Ti6Al4V substrate by electrodeposition under high magnetic field.The electrodeposition is conducted by potentiostatic method on horizontal elect...The present study reports on the growth of calcium phosphate coatings on Ti6Al4V substrate by electrodeposition under high magnetic field.The electrodeposition is conducted by potentiostatic method on horizontal electrode whose roughness was modified to reach a value of 3μm.The coatings are obtained from an electrolyte containing calcium nitrate as the Ca^(2+) source and ammonium phosphate as the P source with a Ca/P ratio equal to two.The LNCMI high field continuous magnet in a 170 mm bore with homogeneity of 600.10~6 in I cm^3 has been used.The magnetic field with a magnitude up to 12 T is applied perpendicularly to the electrode surface.The surface morphology and chemical composition of the obtained coatings were characterized by 3D digital microscope and scanning electron microscopy associated with X-ray microanalysis(SEM-EDX).The phase composition was analyzed by X-Ray diffraction.The presence of several crystalline phases comprising octacalcium phosphate and hydroxyapatite is obtained and magnetic field seems to change the relative importance of these phases.The coating morphology changes from belt shape crystallites to needle shape crystallites with high magnetic field superimposition without important modification of Ca/P ratio in the deposit.On the other hand formation of volcano-like structures due to the presence of hydrogen bubbles during deposition is considerably reduced in the presence of magnetic field.展开更多
To determine whether a biodegradable calcium phosphate cement(CPC) provides significant augmentation of pedicle screw fixation or not,an in vitro biomechanical study was carried out to evaluate the biomechanical effec...To determine whether a biodegradable calcium phosphate cement(CPC) provides significant augmentation of pedicle screw fixation or not,an in vitro biomechanical study was carried out to evaluate the biomechanical effect of CPC in the restoration and augmentation of pedicle screw fixation.Axial pullout test and cyclic bending resistance test were employed in the experiment,and polymethylmethacrylate (PMMA) was chosen as control.The results demonstrate that the pullout strengths following CPC restoration and augmentation are 74% greater on an average than those of the control group,but less than those of PMMA restoration group and augmentation group respectively (increased by 126% versus control).In cyclic bending resistance test,the CPC augmented screws are found to withstand a greater number of cycles or greater loading with less displacement before loosening,but the augmentation effect of PMMA is greater than that of CPC.展开更多
A facile one-step co-precipitation method was demonstrated to fabricate amorphous sulfurcontaining calcium phosphate （SCP） nanoparticles, in which the sulfur group was in-situ introduced into calcium phosphate. The ...A facile one-step co-precipitation method was demonstrated to fabricate amorphous sulfurcontaining calcium phosphate （SCP） nanoparticles, in which the sulfur group was in-situ introduced into calcium phosphate. The resulting SCP exhibited a noticeable enhanced performance for Pb（II） removal in comparison with hydroxyapatite （HAP）, being capable of easily reducing 20 ppm of Pb（II） to below the acceptable standard for drinking water within less than 10 min. Remarkably, the saturated removal capacities of Pb（II） on SCP were as high as 1720.57 mg/g calculated by the Langmuir isotherm model, exceeding largely that of the previously reported absorbents. Significantly, SCP displayed highly selective removal ability toward Pb（II） ions in the presence of the competing metal ions （Ni（II）, Co（II）, Zn（II）, and Cd（II））. Further investigations indicated that such ultra-high removal efficiency and preferable affinity of Pb（II） ions on SCP may be reasonably ascribed to the formation of rodlike hydroxypyromorphite crystals on the surface of SCP via dissolution-precipitation and ion exchange reactions, accompanied by the presence of lead sulfide precipitates. High removal efficiency, fast removal kinetics and excellent selectivity toward Pb（II） made the obtained SCP material an ideal candidate for Pb（II） ions decontamination in practical application.展开更多
For phosphorus （P） recovery from wastewater, the effect of humic substances （HS） on the precipitation of calcium phosphate was studied. Batch experiments of calcium phosphate precipitation were undertaken with syn...For phosphorus （P） recovery from wastewater, the effect of humic substances （HS） on the precipitation of calcium phosphate was studied. Batch experiments of calcium phosphate precipitation were undertaken with synthetic water that contained 20 mg/L phosphate （as P） and 20 mg/L HS （as dissolved organic carbon, DOC） at a constant pH value in the range of 8.0-10.0. The concentration variations of phosphate, calcium （Ca） and HS were measured in the precipitation process; the crystalline state and compositions of the precipitates were analysed by powder X-ray diffraction （XRD） and chemical methods, respectively. It showed that at solution pH 8.0, the precipitation rate and removal efficiency of phosphate were greatly reduced by HS, but at solution pH ≥9.0, the effect of HS was very small. The Ca consumption for the precipitation of phosphate increased when HS was added; HS was also removed from solution with the precipitation of calcium phosphate. At solution pH 8.0 and HS concentrations ≤3.5 mg/L, and at pH ≥ 9.0 and HS concentrations ≤ 10 mg/L, the final precipitates were proved to be hydroxyapatite （HAP） by XRD. The increases of solution pH value and initial Ca/P ratio helped reduce the influence of HS on the precipitation of phosphate.展开更多
Composites containing nanoparticles of amorphous calcium phosphate （NACP） remineralize tooth lesions and inhibit caries. A recent study synthesized quaternary ammonium methacrylates （QAMs） with chain lengths （CLs...Composites containing nanoparticles of amorphous calcium phosphate （NACP） remineralize tooth lesions and inhibit caries. A recent study synthesized quaternary ammonium methacrylates （QAMs） with chain lengths （CLs） of 3-18 and determined their effects on a bonding agent. This study aimed to incorporate these QAMs into NACP nanocomposites for the first time to simultaneously endow the material with antibacterial and remineralizing capabilities and to investigate the effects of the CL on the mechanical and biofilm properties. Five QAMs were synthesized： DMAPM （CL3）, DMAHM （CL6）, DMADDM （CL12）, DMAHDM （CL16）, and DMAODM （CL18）. Each QAM was incorporated into a composite containing 20% NACP and 50% glass fillers. A dental plaque microcosm biofilm model was used to evaluate the antibacterial activity. The flexural strength and elastic modulus of nanocomposites with QAMs matched those of a commercial control composite （n = 6; P 〉 0.1）. Increasing the CL from 3 to 16 greatly enhanced the antibacterial activity of the NACP nanocomposite （P 〈 0.05）; further increasing the CL to 18 decreased the antibacterial potency. The NACP nanocomposite with a CL of 16 exhibited biofilm metabolic activity and acid production that were 10-fold lesser than those of the control composite. The NACP nanocomposite with a CL of 16 produced 2-log decreases in the colony-forming units （CFU） of total microorganisms, total streptococci, and mutans streptococci. In conclusion, QAMs with CLs of 3-18 were synthesized and incorporated into an NACP nanocomposite for the first time to simultaneously endow the material with antibacterial and remineralization capabilities. Increasing the C/reduced the metabolic activity and acid production of biofilms and caused a 2-log decrease in CFU without compromising the mechanical properties. Nanocomposites exhibiting strong anti-biofilm activity, remineralization effects, and mechanical properties are promising materials for tooth restorations that inhibit caries.展开更多
Magnesium has been known as an appropriate biological material on account of its good biocompatibility and biodegradability properties in addition to advantageous mechanical properties.Mg and its alloys are of poor co...Magnesium has been known as an appropriate biological material on account of its good biocompatibility and biodegradability properties in addition to advantageous mechanical properties.Mg and its alloys are of poor corrosion resistance.Its high corrosion rate leads to its quick decomposition in the corrosive ambiance and as a result weakening its mechanical properties and before it is repaired,it will vanish.The corrosion and degradation rate must be controlled in the body to advance the usage of Mg and its alloys as implants.Different techniques have been utilized to boost biological properties.Plasma electrolytic oxidation(PEO)can provide porous and biocompatible coatings for implants among various techniques.Biodegradable implants are generally supposed to show enough corrosion resistance and mechanical integrity in the body environment.Much research has been carried out in order to produce PEO coatings containing calcium phosphate compounds.Calcium phosphates are really similar to bone mineral composition and present great biocompatibility.The present study deals with the usage of calcium phosphates as biocompatible coatings applied on Mg and its alloys to study the properties and control the corrosion rate.展开更多
Calcium phosphate cements(CPCs)are frequently used to repair bone defects.Since their discovery in the 1980s,extensive research has been conducted to improve their properties,and emerging evidence supports their incre...Calcium phosphate cements(CPCs)are frequently used to repair bone defects.Since their discovery in the 1980s,extensive research has been conducted to improve their properties,and emerging evidence supports their increased application in bone tissue engineering.Much effort has been made to enhance the biological performance of CPCs,including their biocompatibility,osteoconductivity,osteoinductivity,biodegradability,bioactivity,and interactions with cells.This review article focuses on the major recent developments in CPCs,including 3D printing,injectability,stem cell delivery,growth factor and drug delivery,and pre-vascularization of CPC scaffolds via co-culture and tri-culture techniques to enhance angiogenesis and osteogenesis.展开更多
Dental composites are commonly used restorative materials; however, secondary caries due to biofilm acids remains a major problem. The objectives of this study were （1） to develop a composite containing quaternary a...Dental composites are commonly used restorative materials; however, secondary caries due to biofilm acids remains a major problem. The objectives of this study were （1） to develop a composite containing quaternary ammonium dimethacrylate （QADM）, nanoparticles of silver （NAg）, and nanoparticles of amorphous calcium phosphate （NACP）, and （2） to conduct the first investigation of the mechanical properties, biofilm response and acid production vs water-ageing time from 1 day to 12 months. A 4 x 5 design was utilized, with four composites （NACP-QADM composite, NACP-NAg composite, NACP-QADM-NAg composite, and a commercial control composite）, and five water-ageing time periods （1 day, and 3, 6, 9, and 12 months）. After each water- ageing period, the mechanical properties of the resins were measured in a three-point flexure, and antibacterial properties were tested via a dental plaque biofilm model using human saliva as an inoculum. After 12 months of water-ageing, NACP-QADM- NAg had a flexural strength and elastic modulus matching those of the commercial control （P〉 0.1）. Incorporation of QADM or NAg into the NACP composite greatly reduced biofilm viability, metabolic activity and acid production. A composite containing both QADM and NAg possessed a stronger antibacterial capability than one with QADM or NAg alone （P〈0.05）. The anti-biofilm activity was maintained after 12 months of water-ageing and showed no significant decrease with increasing time （P〉0.1）. In conclusion, the NACP-QADM-NAg composite decreased biofilm viability and lactic acid production, while matching the load- bearing capability of a commercial composite. There was no decrease in its antibacterial properties after 1 year of water-ageing. The durable antibacterial and mechanical properties indicate that NACP-QADM-NAg composites may be useful in dental restorations to combat caries.展开更多
The influences of pH value, electrolyte temperature and loading time on depositing calcium phosphate coating on pure titanium substrate by electrodeposition process were investigated. The process was carried out with ...The influences of pH value, electrolyte temperature and loading time on depositing calcium phosphate coating on pure titanium substrate by electrodeposition process were investigated. The process was carried out with an electrochemical work-station supplying a direct current power at potential of -0.8V （vs SCE）. The electrolyte consists of 7 mmol·L-1 CaCl2·2H2O, 3 mmol·L-1 Ca（H2PO4）2·H2O and 2.5% H2O2. NaOH and HCl solutions were used to adjust pH value. The deposited samples were characterized by X-ray diffraction and scanning electron microscope. The comparison of the deposits obtained at lower and higher pH values demonstrates that the crystallization process at the interface is favoured by high pH value. With temperature increasing, the deposited hydroxyapatite is occasionally of plate-like shape, and the width and the length of the deposited calcium phosphates at 65 ℃ are larger than those at 55 ℃. Therefore, it is confirmed that the morphology and microstructure of electrochemically deposited calcium phosphates can be regulated. Additionally, the coating formed in electrolyte with H2O2 additive is homogeneous and the evolution of H2 bubble can be eliminated.展开更多
Tissue engineering is promising to meet the increasing need for bone regeneration. Nanostructured calcium phosphate （CAP） biomaterials/scaffolds are of special interest as they share chemical/crystallographic simila...Tissue engineering is promising to meet the increasing need for bone regeneration. Nanostructured calcium phosphate （CAP） biomaterials/scaffolds are of special interest as they share chemical/crystallographic similarities to inorganic components of bone. Three applications of nano-CaP are discussed in this review： nanostructured calcium phosphate cement （CPC）; nano-CaP composites; and nano-CaP coatings. The interactions between stem cells and nano-CaP are highlighted, including cell attachment, orientation/ morphology, differentiation and in vivo bone regeneration. Several trends can be seen： （i） nano-CaP biomaterials support stem cell attachment/proliferation and induce osteogenic differentiation, in some cases even without osteogenic supplements; （ii） the influence of nano-CaP surface patterns on cell alignment is not prominent due to non-uniform distribution of nano-crystals; （iii） nano-CaP can achieve better bone regeneration than conventional CaP biomaterials; （iv） combining stem cells with nano-CaP accelerates bone regeneration, the effect of which can be further enhanced by growth factors; and （v） cell microencapsulation in nano-CaP scaffolds is promising for bone tissue engineering. These understandings would help researchers to further uncover the underlying mechanisms and interactions in nano-CaP stem cell constructs in vitro and in vivo, tailor nano-CaP composite construct design and stem cell type selection to enhance cell function and bone regeneration, and translate laboratory findings to clinical treatments.展开更多
文摘The influence of different surface coatings of NiTi shape memory allays was examined using in vitro testing methods. Plates of superelastic nickel-titanium shape memory allay （ NiTi ） were coated with calcium phosphates （ hydroxyapatite ） by high-temperature plasma-spraying or by dip-coating. The biocompatibility was tested in vitro by cultivation of isolated human granulocytes and whole blood cells. As substrates, pure NiTi, plasma-spray-coated NiTi and dip-coated NiTi were used. Isolated granulocytes showed an increased adhesion to both calcium phosphate-coated NiTi samples. Compared to non-coated NiTi or dip-coated NiTi, the number of dead granulocytes adherent to plasma-sprayed surfaces was significantly increased （ p 〈 0.01 ）. Whether the d/f- ferences in apoptosis of granulocytes on dip-coated vs plasma-sprayed coatings observed are due to differences in material surface morphologies has to be analyzed in further studies. Because of the cellular interactions with the coating layers, h is likely that the results obtained are not caused by the underlying NiTi but due to the coating itself.
基金financial support from the European Union’s Horizon 2020 research and innovation programme under the grant agreement No 857287(BBCE).
文摘Out of the wide range of calcium phosphate(CaP)biomaterials,calcium phosphate bone cements(CPCs)have attracted increased attention since their discovery in the 1980s due to their valuable properties such as bioactivity,osteoconductivity,injectability,hardening ability through a low-temperature setting reaction and moldability.Thereafter numerous researches have been performed to enhance the properties of CPCs.Nonetheless,low mechanical performance of CPCs limits their clinical application in load bearing regions of bone.Also,the in vivo resorption and replacement of CPC with new bone tissue is still controversial,thus further improvements of high clinical importance are required.Bioactive glasses(BGs)are biocompatible and able to bond to bone,stimulating new bone growth while dissolving over time.In the last decades extensive research has been performed analyzing the role of BGs in combination with different CaPs.Thus,the focal point of this review paper is to summarize the available research data on how injectable CPC properties could be improved or affected by the addition of BG as a secondary powder phase.It was found that despite the variances of setting time and compressive strength results,desirable injectable properties of bone cements can be achieved by the inclusion of BGs into CPCs.The published data also revealed that the degradation rate of CPCs is significantly improved by BG addition.Moreover,the presence of BG in CPCs improves the in vitro osteogenic differentiation and cell response as well as the tissue-material interaction in vivo.
文摘Calcium phosphates are a family of compounds with different chemical compositions, structures and properties containing calcium ions and functional groups of orthophosphate （ pO34- ）, metaphosphate （ PO3- ） or pyrophosphate （ P2O4-7 ） and sometimes hydrogen or hydroxide ions. Calcium phosphates can be widely found in nature as well as in hard tissues （bone and tooth） of the vertebrate. Owing to similar chemical composition and structure to the main inorganic constituents of bone and tooth, calcium phosphate-based materials are promising biomaterials with high biocompatibility, and have been investigated for applications in various biomedical areas. Calcium silicate-based materials have attracted much attention on their potential applications in various biomedical fields such as bone de- fect repair and drug delivery. In recent years, this research group has been focusing on the research in this exciting and rapidly evolving research field, and has published many papers. This article will provide a brief review on our main research work on the synthesis, characterization, properties and applications of nanostructured materials of calcium phosphates and calcium silicates. Finally, future perspectives and challenges for the research and applica- tions of nanostructured materials of calcium phosphates and calcium silicates are discussed.
基金National Natural Science Foundation of China(51172260,51102258)Science and Technology Commission of Shanghai(1052nm06200,11nm0506600,11ZR1441800)Chinese Nano-973 Project(2010CB933901)is gratefully acknowledged.
文摘Due to the similar chemical properties to the inorganic component in calcified tissues,synthetic calcium phosphate has been considered as ideal biomaterials with excellent biocompatibility.Nanostructured calcium phosphate materials play an important role in the formation of hard tissues in nature.It is reported that calcium phosphates materials in nano-size can mimic the dimensions of constituent components of calcified tissues.Recently,the synthesis and application of nanostructured calcium phosphate materials have become a very hot field.Lots of methods have been reported to prepare nanostructured calcium phosphate,and various morphologies including nanoparticles,plate-like nanocrystals,nano-needles,whiskers/fibres/wires,mesoporous,nanotubes,nano-blades,and powders with three-dimensional(3-D)structures have been obtained.More studies of nanostructured calcium phosphates are expected in biomedical area,such as tissue engineering scaffolds,drug/gene delivery systems and multifunctional systems.In this article,the synthesis and application of nanostructured calcium phosphates are reviewed and discussed.
基金financially supported by the National Natural Science Foundation of China(Nos.82203680 and 52273278)the Natural Scientific Foundation of Liaoning Province(No.2021-MS-176)+1 种基金Shenyang Bureau of Science and Technology(No.RC230527)the Central Guidance Funding for Local Scientific and Techno-logical Development in Liaoning(No.2023JH6/100100029).
文摘Guided bone regeneration in the alveolar bone relies on the colonization and differentiation of immune cells within the defect area.The absence of osteoinductive and osteoimmune properties of currently available scaffolds hinders to achieve optimal repair outcomes in clinical settings.Thus,we aimed to enhance the bone repair ability of polycaprolactone(PCL)scaffolds by incorporating osteoinductive amorphous calcium phosphate(ACP)with immune-regulating zinc ions(ACP(Zn),ACZP),to create a favorable immunomodulatory microenvironment.After one day of co-culture with PCL-ACZP,the spreading area of macrophage cells was significantly higher than that from the original PCL scaffold.Additionally,over 32.1%of macrophages exhibited M2 polarization within three days of co-culture.The PCLACZP/macrophage-conditioned medium significantly boosted osteogenic gene expression in MC3T3-E1 cells.After eight weeks of implantation in a rat femoral condyle defect,the BV/TV from the PCL-ACZP group reached 32.9%,1.4 times of that from the PCL group.Furthermore,the PCL-ACZP-GelMA biphasic module as prepared successfully achieved complete regeneration of three-walled alveolar bone defects in rabbits,resulting in arch-shaped alveolar bone repair and providing greater convenience in the clinical settings.This study showcased the effectiveness of PCL-ACZP-GelMA biphasic module as bioactive scaffolds in the morphological restoration of alveolar bone.
基金supported by the Japan Society for the Promotion of Science(JSPS)KAKENHI Grant Number JP22H01581the authors sincerely acknowledge the support.
文摘Bio-mediated soil improvement methods keep on gaining the attention of geotechnical engineers and researchers globally due to their nature-based elegance and eco-friendliness.Most prevalent bio-mediated soil improvement methods include microbially induced carbonate precipitation(MICP)and enzyme-induced carbonate precipitation(EICP).During their processes,the bacteria/free urease hydrolyzes the urea into ammonium and carbonic acid,which is accompanied by a considerable increase of alkalinity(about pH 9.0).The major problem associated with the above techniques is the release of gaseous ammonia that is extremely detrimental.Therefore,this study aims to propose a new sustainable approach involving lactic acid bacteria to facilitate the calcium phosphate mineralization for the strengthening of sand matrix.The major objectives of this investigation are:(i)to evaluate the urease activity of the lactic acid bacteria under different temperatures,pH conditions and additions of metal ions,(ii)to assess the treated sand matrix,(iii)to perform cost analysis.The outcomes indicated that Limosilactobacillus sp.could effectively facilitate the urea hydrolysis,hence increasing the pH from acidic to neutral and providing a desirable environment for the calcium phosphate to mineralize within the voids of the sand.The addition of 0.01%Ni^(2+)in culture media was found to enhance the urease activity by 38.8%and compressive strength over 40%.A combined formation of amorphous-and whisker-like precipitates could bridge a larger area at particle-particle contact points,thereby faciliating a strong force-network in sand matrix.The mineralized calcium phosphate compound was found to be brushite.The cost herein for producing 1 L treatment solution was estimated to be about 2.5-folds and 11.8-folds lower compared to that of MICP and EICP treatment solutions,respectively.Moreover,since the treatment pH could potentially be regulated between acidic-neural range,it would greatly control the release of gaseous ammonia.With several environmental and economical benefits,the study has disclosed a new sustainable direction for sand improvement via the use of lactic acid bacteria.
基金supported by the Natural Science Foundation of Chongqing(Grant No.csts2018jcyjAX0016)Funded by the Senior Medical Talents Program of Chongqing for Young and Middle-aged.
文摘The possible application of magnesium(Mg)in glaucoma surgical treatment has been investigated in our previous work.In this paper,the degradation behavior and biocompatibility of Mg coated with hydroxyapatite(HA)and dicalcium phosphate dihydrate(DCPD)in eye environment were evaluated,and uncoated Mg was used for comparison.It was found that uniform corrosion occurred macroscopically to the coated Mg samples in sodium lactate ringer’s injection(SLRI)as well as in the rabbit eyes.In micro-scale,the corrosion was characterized by local cracking and pitting primarily.Mg and calcium(Ca)were incorporated into the surface corrosion products and a multi-layer structure was formed.Compared to other samples,HA-coated Mg slowed down dramatically the alkalinity of the solution and the ion release of the sample,and exhibited the lowest corrosion rate in SLRI,which was about 0.22 mm/a.In terms of biocompatibility,fibroblasts demonstrated high viability in the HA-coated and DCPD-coated Mg groups(p<0.05)in vitro.In vivo,HA-coated Mg was found to show lower inflammatory response and fibrosis than the other groups did,as indicated by hematoxylin-eosin and immunofluorescence staining.During the degrading process of HA-coated Mg in the rabbits’eyes,no inflammation was found in the anterior chamber,lens,and vitreous body.HA-coated Mg was fully biodegraded fifteen weeks post-operation,and the scleral drainage channel(SDC)was formed without obvious scarring.It is concluded that HA-coated Mg implantation is a promising adjunctive procedure to improve the success rate of trabeculectomy.Statement of significance:Magnesium(Mg)has shown to be a potential biomaterial for ophthalmic implants in our previous work.However,inflammatory response resulted from the low corrosion resistance of Mg is a major concern.It is shown here that Mg coated with different calcium phosphates can improve these properties in varying degrees and keep the scleral drainage channel unobstructed and unscarred.Based on our in vitro and in vivo studies,HA-coated Mg exhibited a better degradation behavior and excellent biocompatibility.The scleral drainage channel still exists and aqueous humor flows out smoothly after the full degradation of the implant.It is concluded that HA-coated Mg is a promising biomaterial to increase the therapeutic efficiency of trabeculectomy for glaucoma.
基金Project(51571134)supported by the National Natural Science Foundation of ChinaProject(2014TDJH104)supported by the SDUST Research Fund+1 种基金the Joint Innovative Centre for Safe and Effective Mining Technology and Equipment of Coal Resources,Shandong Province,ChinaProject(cstc2012jj A50034)supported by the Natural Science Foundation of Chongqing,China
文摘Zinc calcium phosphate （Zn-Ca-P） coating and cerium-doped zinc calcium phosphate （Zn-Ca-Ce-P） coating were prepared on AZ31 magnesium alloy. The chemical compositions, morphologies and corrosion resistance of coatings were investigated through energy-dispersive X-ray spectroscopy （EDS）, X-ray photoelectron spectroscopy （XPS）, X-ray diffraction （XRD）, electron probe micro-analysis （EPMA） and scanning electron microscopy （SEM） together with hydrogen volumetric and electrochemical tests. The results indicate that both coatings predominately contain crystalline hopeite （Zn3（PO4）2·4H2O）, Mg3（PO4）2 and Ca3（PO4）2, and traces of non-crystalline MgF2 and CaF2. The Zn-Ca-Ce-P coating is more compact than the Zn-Ca-P coating due to the formation of CePO4, and displays better corrosion resistance than the Zn-Ca-P coating. Both coatings protect the AZ31 Mg substrate only during an initial immersion period. The micro-galvanic corrosion between the coatings and their substrates leads to an increase of hydrogen evolution rate （HER） with extending the immersion time. The addition of Ce promotes the homogenous distribution of Ca and formation of hopeite. The Zn-Ca-Ce-P coating has the potential for the primer coating on magnesium alloys.
文摘Stones in the seminal vesicles are extremely rare. We present a 62-year-old patient with a stone within a seminal vesicle cyst, who was cured by laparoscopic treatment. The operative time was 80 rnin, and the estimated blood loss was 90 mL. Scanning electron microscope examination of the stone showed a compact crystal image externally and sparse spherical crystal structure in kernel. Composition of the stone was calcium fluorophosphate on X-ray diffractometer. The follow-up time was 15 months with no recurrence of cyst or stone. To our knowledge, this case is the first to describe laparoscopic removal of a stone within a seminal vesicle cyst, and the first to describe calcium fluorophosphate as the composition of seminal vesicle stones. （Asian JAndro12008 Mar; 10： 337-340）
文摘Current calcium phosphate （ CaP ） biomaterials for bone repair, substitution, augmentation and regeneration include hydroxyapatite （ HA ） from synthetic or biologic origin, beta-tricaicium phosphate （ β- TCP ）, biphasic calcium phosphate （BCP）, and are available as granules, porous blocks, components of compashes （CaP/pollymer） cements, and as coatings on orthopedic and dental implants. Experimental calcium phosphate biomaterials include CO3^- and F-substituted apatites, Mg-and Zn-substituted β-TCP, calcium phosphate glasses, This paper is a brief review of the different types of CaP biomaterials and their properties such as bioactivity , osteoconductivity , osteoinductivity.
文摘The present study reports on the growth of calcium phosphate coatings on Ti6Al4V substrate by electrodeposition under high magnetic field.The electrodeposition is conducted by potentiostatic method on horizontal electrode whose roughness was modified to reach a value of 3μm.The coatings are obtained from an electrolyte containing calcium nitrate as the Ca^(2+) source and ammonium phosphate as the P source with a Ca/P ratio equal to two.The LNCMI high field continuous magnet in a 170 mm bore with homogeneity of 600.10~6 in I cm^3 has been used.The magnetic field with a magnitude up to 12 T is applied perpendicularly to the electrode surface.The surface morphology and chemical composition of the obtained coatings were characterized by 3D digital microscope and scanning electron microscopy associated with X-ray microanalysis(SEM-EDX).The phase composition was analyzed by X-Ray diffraction.The presence of several crystalline phases comprising octacalcium phosphate and hydroxyapatite is obtained and magnetic field seems to change the relative importance of these phases.The coating morphology changes from belt shape crystallites to needle shape crystallites with high magnetic field superimposition without important modification of Ca/P ratio in the deposit.On the other hand formation of volcano-like structures due to the presence of hydrogen bubbles during deposition is considerably reduced in the presence of magnetic field.
文摘To determine whether a biodegradable calcium phosphate cement(CPC) provides significant augmentation of pedicle screw fixation or not,an in vitro biomechanical study was carried out to evaluate the biomechanical effect of CPC in the restoration and augmentation of pedicle screw fixation.Axial pullout test and cyclic bending resistance test were employed in the experiment,and polymethylmethacrylate (PMMA) was chosen as control.The results demonstrate that the pullout strengths following CPC restoration and augmentation are 74% greater on an average than those of the control group,but less than those of PMMA restoration group and augmentation group respectively (increased by 126% versus control).In cyclic bending resistance test,the CPC augmented screws are found to withstand a greater number of cycles or greater loading with less displacement before loosening,but the augmentation effect of PMMA is greater than that of CPC.
文摘A facile one-step co-precipitation method was demonstrated to fabricate amorphous sulfurcontaining calcium phosphate （SCP） nanoparticles, in which the sulfur group was in-situ introduced into calcium phosphate. The resulting SCP exhibited a noticeable enhanced performance for Pb（II） removal in comparison with hydroxyapatite （HAP）, being capable of easily reducing 20 ppm of Pb（II） to below the acceptable standard for drinking water within less than 10 min. Remarkably, the saturated removal capacities of Pb（II） on SCP were as high as 1720.57 mg/g calculated by the Langmuir isotherm model, exceeding largely that of the previously reported absorbents. Significantly, SCP displayed highly selective removal ability toward Pb（II） ions in the presence of the competing metal ions （Ni（II）, Co（II）, Zn（II）, and Cd（II））. Further investigations indicated that such ultra-high removal efficiency and preferable affinity of Pb（II） ions on SCP may be reasonably ascribed to the formation of rodlike hydroxypyromorphite crystals on the surface of SCP via dissolution-precipitation and ion exchange reactions, accompanied by the presence of lead sulfide precipitates. High removal efficiency, fast removal kinetics and excellent selectivity toward Pb（II） made the obtained SCP material an ideal candidate for Pb（II） ions decontamination in practical application.
基金The German Research Foundation (DFG-Graduiertenkolleg 366) Grant Program for the High-Level Returned Scholars fromAbroad, Ministry of Personnel of China (No. 2004-2005)
文摘For phosphorus （P） recovery from wastewater, the effect of humic substances （HS） on the precipitation of calcium phosphate was studied. Batch experiments of calcium phosphate precipitation were undertaken with synthetic water that contained 20 mg/L phosphate （as P） and 20 mg/L HS （as dissolved organic carbon, DOC） at a constant pH value in the range of 8.0-10.0. The concentration variations of phosphate, calcium （Ca） and HS were measured in the precipitation process; the crystalline state and compositions of the precipitates were analysed by powder X-ray diffraction （XRD） and chemical methods, respectively. It showed that at solution pH 8.0, the precipitation rate and removal efficiency of phosphate were greatly reduced by HS, but at solution pH ≥9.0, the effect of HS was very small. The Ca consumption for the precipitation of phosphate increased when HS was added; HS was also removed from solution with the precipitation of calcium phosphate. At solution pH 8.0 and HS concentrations ≤3.5 mg/L, and at pH ≥ 9.0 and HS concentrations ≤ 10 mg/L, the final precipitates were proved to be hydroxyapatite （HAP） by XRD. The increases of solution pH value and initial Ca/P ratio helped reduce the influence of HS on the precipitation of phosphate.
基金supported by National Institutes of Health (NIH) R01DE17974 (Hockin HK Xu)National Natural Science Foundation of China grant 81400540 (Ke Zhang)a seed fund (Hockin HK Xu) from the University of Maryland School of Dentistry
文摘Composites containing nanoparticles of amorphous calcium phosphate （NACP） remineralize tooth lesions and inhibit caries. A recent study synthesized quaternary ammonium methacrylates （QAMs） with chain lengths （CLs） of 3-18 and determined their effects on a bonding agent. This study aimed to incorporate these QAMs into NACP nanocomposites for the first time to simultaneously endow the material with antibacterial and remineralizing capabilities and to investigate the effects of the CL on the mechanical and biofilm properties. Five QAMs were synthesized： DMAPM （CL3）, DMAHM （CL6）, DMADDM （CL12）, DMAHDM （CL16）, and DMAODM （CL18）. Each QAM was incorporated into a composite containing 20% NACP and 50% glass fillers. A dental plaque microcosm biofilm model was used to evaluate the antibacterial activity. The flexural strength and elastic modulus of nanocomposites with QAMs matched those of a commercial control composite （n = 6; P 〉 0.1）. Increasing the CL from 3 to 16 greatly enhanced the antibacterial activity of the NACP nanocomposite （P 〈 0.05）; further increasing the CL to 18 decreased the antibacterial potency. The NACP nanocomposite with a CL of 16 exhibited biofilm metabolic activity and acid production that were 10-fold lesser than those of the control composite. The NACP nanocomposite with a CL of 16 produced 2-log decreases in the colony-forming units （CFU） of total microorganisms, total streptococci, and mutans streptococci. In conclusion, QAMs with CLs of 3-18 were synthesized and incorporated into an NACP nanocomposite for the first time to simultaneously endow the material with antibacterial and remineralization capabilities. Increasing the C/reduced the metabolic activity and acid production of biofilms and caused a 2-log decrease in CFU without compromising the mechanical properties. Nanocomposites exhibiting strong anti-biofilm activity, remineralization effects, and mechanical properties are promising materials for tooth restorations that inhibit caries.
文摘Magnesium has been known as an appropriate biological material on account of its good biocompatibility and biodegradability properties in addition to advantageous mechanical properties.Mg and its alloys are of poor corrosion resistance.Its high corrosion rate leads to its quick decomposition in the corrosive ambiance and as a result weakening its mechanical properties and before it is repaired,it will vanish.The corrosion and degradation rate must be controlled in the body to advance the usage of Mg and its alloys as implants.Different techniques have been utilized to boost biological properties.Plasma electrolytic oxidation(PEO)can provide porous and biocompatible coatings for implants among various techniques.Biodegradable implants are generally supposed to show enough corrosion resistance and mechanical integrity in the body environment.Much research has been carried out in order to produce PEO coatings containing calcium phosphate compounds.Calcium phosphates are really similar to bone mineral composition and present great biocompatibility.The present study deals with the usage of calcium phosphates as biocompatible coatings applied on Mg and its alloys to study the properties and control the corrosion rate.
基金supported by NIH R01 DE14190 and R21 DE22625(HX)the National Science Foundation of China 81401794(PW)and 81400487(LW)+2 种基金the Youth Fund of Science and Technology of Jilin Province 20150520043JH(LW)the China Postdoctoral Science Foundation 2015M581405(LW)the University of Maryland School of Dentistry bridge fund(HX)
文摘Calcium phosphate cements(CPCs)are frequently used to repair bone defects.Since their discovery in the 1980s,extensive research has been conducted to improve their properties,and emerging evidence supports their increased application in bone tissue engineering.Much effort has been made to enhance the biological performance of CPCs,including their biocompatibility,osteoconductivity,osteoinductivity,biodegradability,bioactivity,and interactions with cells.This review article focuses on the major recent developments in CPCs,including 3D printing,injectability,stem cell delivery,growth factor and drug delivery,and pre-vascularization of CPC scaffolds via co-culture and tri-culture techniques to enhance angiogenesis and osteogenesis.
基金supported by the International Science and Technology Cooperation Program of China (2014DFE30180) (Xue-Dong Zhou)National Natural Science Foundation of China grant 81430011 (Xue-Dong Zhou),81372889 (Lei Cheng),81400540 (Ke Zhang)+1 种基金?nancial support from the School of Stomatology at the Capital Medical University in China (Ke Zhang),NIH R01 DE17974 (Hockin HK Xu)a seed grant from the University of Maryland School of Dentistry (Hockin HK Xu)
文摘Dental composites are commonly used restorative materials; however, secondary caries due to biofilm acids remains a major problem. The objectives of this study were （1） to develop a composite containing quaternary ammonium dimethacrylate （QADM）, nanoparticles of silver （NAg）, and nanoparticles of amorphous calcium phosphate （NACP）, and （2） to conduct the first investigation of the mechanical properties, biofilm response and acid production vs water-ageing time from 1 day to 12 months. A 4 x 5 design was utilized, with four composites （NACP-QADM composite, NACP-NAg composite, NACP-QADM-NAg composite, and a commercial control composite）, and five water-ageing time periods （1 day, and 3, 6, 9, and 12 months）. After each water- ageing period, the mechanical properties of the resins were measured in a three-point flexure, and antibacterial properties were tested via a dental plaque biofilm model using human saliva as an inoculum. After 12 months of water-ageing, NACP-QADM- NAg had a flexural strength and elastic modulus matching those of the commercial control （P〉 0.1）. Incorporation of QADM or NAg into the NACP composite greatly reduced biofilm viability, metabolic activity and acid production. A composite containing both QADM and NAg possessed a stronger antibacterial capability than one with QADM or NAg alone （P〈0.05）. The anti-biofilm activity was maintained after 12 months of water-ageing and showed no significant decrease with increasing time （P〉0.1）. In conclusion, the NACP-QADM-NAg composite decreased biofilm viability and lactic acid production, while matching the load- bearing capability of a commercial composite. There was no decrease in its antibacterial properties after 1 year of water-ageing. The durable antibacterial and mechanical properties indicate that NACP-QADM-NAg composites may be useful in dental restorations to combat caries.
文摘The influences of pH value, electrolyte temperature and loading time on depositing calcium phosphate coating on pure titanium substrate by electrodeposition process were investigated. The process was carried out with an electrochemical work-station supplying a direct current power at potential of -0.8V （vs SCE）. The electrolyte consists of 7 mmol·L-1 CaCl2·2H2O, 3 mmol·L-1 Ca（H2PO4）2·H2O and 2.5% H2O2. NaOH and HCl solutions were used to adjust pH value. The deposited samples were characterized by X-ray diffraction and scanning electron microscope. The comparison of the deposits obtained at lower and higher pH values demonstrates that the crystallization process at the interface is favoured by high pH value. With temperature increasing, the deposited hydroxyapatite is occasionally of plate-like shape, and the width and the length of the deposited calcium phosphates at 65 ℃ are larger than those at 55 ℃. Therefore, it is confirmed that the morphology and microstructure of electrochemically deposited calcium phosphates can be regulated. Additionally, the coating formed in electrolyte with H2O2 additive is homogeneous and the evolution of H2 bubble can be eliminated.
基金supported by NIH R01 DE14190 and R21 DE22625 (HX)National Science Foundation of China 31100695 and 31328008 (LZ), 81401794 (PW)Maryland Stem Cell Research Fund and University of Maryland School of Dentistry
文摘Tissue engineering is promising to meet the increasing need for bone regeneration. Nanostructured calcium phosphate （CAP） biomaterials/scaffolds are of special interest as they share chemical/crystallographic similarities to inorganic components of bone. Three applications of nano-CaP are discussed in this review： nanostructured calcium phosphate cement （CPC）; nano-CaP composites; and nano-CaP coatings. The interactions between stem cells and nano-CaP are highlighted, including cell attachment, orientation/ morphology, differentiation and in vivo bone regeneration. Several trends can be seen： （i） nano-CaP biomaterials support stem cell attachment/proliferation and induce osteogenic differentiation, in some cases even without osteogenic supplements; （ii） the influence of nano-CaP surface patterns on cell alignment is not prominent due to non-uniform distribution of nano-crystals; （iii） nano-CaP can achieve better bone regeneration than conventional CaP biomaterials; （iv） combining stem cells with nano-CaP accelerates bone regeneration, the effect of which can be further enhanced by growth factors; and （v） cell microencapsulation in nano-CaP scaffolds is promising for bone tissue engineering. These understandings would help researchers to further uncover the underlying mechanisms and interactions in nano-CaP stem cell constructs in vitro and in vivo, tailor nano-CaP composite construct design and stem cell type selection to enhance cell function and bone regeneration, and translate laboratory findings to clinical treatments.
