Shaking table tests of a 1:10 scale arch model performed to investigate the seismic behavior and resistance of concrete filled steel tubular (CFT) arch structures are described in this paper. The El-Centro record and ...Shaking table tests of a 1:10 scale arch model performed to investigate the seismic behavior and resistance of concrete filled steel tubular (CFT) arch structures are described in this paper. The El-Centro record and Shanghai artificial wave were adopted as the input excitation. The entire test process can be divided into three stages depending on the lateral brace configurations, i.e., fully (five) braced, two braces removed, and all braces removed. A total of 46 tests, starting from the elastic state to failure condition, have been conducted. The natural vibration frequencies, responses of acceleration, displacement and strain were measured. From the test results, it is demonstrated that the CFT arch structures are capable of resisting severe ground motions and that CFT arches offer a credible alternative to reinforced concrete arches, especially in regions of high seismic intensity.展开更多
High-pile and beam-slab quays have been widely used after several years development. They are mature enough to be one of the most important structural types of wharves in China coastal areas. In order to accommodate l...High-pile and beam-slab quays have been widely used after several years development. They are mature enough to be one of the most important structural types of wharves in China coastal areas. In order to accommodate large tonnage vessels, wharves should be eorrstructed in deep water gradually. However, conventional high-pile and beam-slab structares are hard to meet the requirements of large deep-water wharf. According to arch＇ s stress characteristics, a new type of wharf with catenary arched longitudinal beams is presented in this paper. The new wharf structure can make full use of arch＇s overhead crossing and reinforced concrete compression resistance, improve the interval between transverse bents greatly, and decrease underwater construction quantity. Thus, the construction cost cab be reduced. Take the third phase project of the Yangshan Deep-water Port for example, comparative analysis on catenary arched longitudinal beams and conventional longitudinal beams has been made. The result shows that with the same wharf length and width, the same loads and same longitudinal beam moment, catenary arch structure can improve the interval between bents up to 28 m, decrease the nmnber of piles and underwater construction quantity.展开更多
The wind-induced dynamic response of long-span light-weight steel arch structure of the global transportation center (GTC) of Beijing Capital International Airport was studied. A composite technique with combination o...The wind-induced dynamic response of long-span light-weight steel arch structure of the global transportation center (GTC) of Beijing Capital International Airport was studied. A composite technique with combination of WAWS(Weighted Amplitude Wavelet Superposition) and FFT(Fast Fourier Transformation) was introduced to simulate wind velocity time series of hundreds of spatial points simultaneously. The structural shape factors of wind load was obtained from wind tunnel model test. The wind vibration factor based on structural displacement response was investigated. After comparing the computational results with wind tunnel model test data, it was found out that the two results accord with each other if wind comes from 0° direction angle, but are quite different if wind comes from 180° direction angle in the area blocked off by airport terminals. The possible reasons of this difference were analyzed. Haar wavelet was used to transform and analyze wind velocity time series and structural wind-induced dynamic responses. The relationship between exciting wind loads and structural responses was studied in time and frequency domains.展开更多
This paper presents a method for isolatedly solving the normal mode of vi-bration according to the uncoupling condition of vibrations inside and outside the archplane.The finite element method for curved beam elements...This paper presents a method for isolatedly solving the normal mode of vi-bration according to the uncoupling condition of vibrations inside and outside the archplane.The finite element method for curved beam elements is adopted to analyse the dy-namic characteristics of arch structures and the calculating program is made.The resultsobtained from Apple II microcomputer are compared with those from SAP5 program byan example,and are in good agreement.展开更多
Based on the analyses on arch and peltate venation structures, the design of reinforcing frames was improved. First, distribution rules of the arch structure were summarized. According to the load condition and the st...Based on the analyses on arch and peltate venation structures, the design of reinforcing frames was improved. First, distribution rules of the arch structure were summarized. According to the load condition and the structure of the frame, a mechanical model of arch structure was devel- oped, and two solutions for the model were analyzed and compared with each other. Through the a- nalysis, application rules of arch structure for improving the design were obtained. Then, distribu- tion rules of peltate venation structure were summarized. By using the same method, application rules of peltate venation structure for improving the design were also obtained. Finally, mechanical problem of the frame was described, and rib arrangement of the frame was redesigned. A parameter optimization for the widths of ribs in bionic arrangement was also carried out to accomplish the im- proving design. Comparison between bionic and conventional reinforcing frames shows that the weight is reduced by as much as 15.3%.展开更多
Aimed at the frozen soil arch reinforcement form of upside shed used for the shield machine launching in tunneling the internal force of the structure was calculated with the aid of the structural mechanics theory. Co...Aimed at the frozen soil arch reinforcement form of upside shed used for the shield machine launching in tunneling the internal force of the structure was calculated with the aid of the structural mechanics theory. Considering the space characteristics of the structure, this calculating method is suitable for practical engineering. Moreover, the behavior of the freezing arch reinforcement structure was analyzed combined with an engineering case.展开更多
<div style="text-align:justify;"> Arches are employed for bridges. This particular type of structures, characterized by a very old use tradition, is nowadays, widely exploited because of its strength, ...<div style="text-align:justify;"> Arches are employed for bridges. This particular type of structures, characterized by a very old use tradition, is nowadays, widely exploited because of its strength, resilience, cost-effectiveness and charm. In recent years, a more conscious design approach that focuses on a more proper use of the building materials combined with the increasing of the computational capability of the modern computers, has led the research in the civil engineering field to the study of optimization algorithms applications aimed at the definition of the best design parameters. In this paper, a differential formulation and a MATLAB code for the calculation of the internal stresses in the arch structure are proposed. Then, the application of a machine learning algorithm, the genetic algorithm, for the calculation of the geometrical parameters, that allows to minimize the quantity of material that constitute the arch structures, is implemented. In this phase, the method used to calculate the stresses has been considered as a constraint function to reduce the range of the solutions to the only ones able to bear the design loads with the smallest volume. In particular, some case studies with different cross-sections are reported to prove the validity of the method and to compare the obtained results in terms of optimization effectiveness. </div>展开更多
基金This study was supported by the National Natural Science Foundation of China under Grant No.50078016Open Funding of State Key Laboratory for Disaster Reduction in Civil Engineering,China.
文摘Shaking table tests of a 1:10 scale arch model performed to investigate the seismic behavior and resistance of concrete filled steel tubular (CFT) arch structures are described in this paper. The El-Centro record and Shanghai artificial wave were adopted as the input excitation. The entire test process can be divided into three stages depending on the lateral brace configurations, i.e., fully (five) braced, two braces removed, and all braces removed. A total of 46 tests, starting from the elastic state to failure condition, have been conducted. The natural vibration frequencies, responses of acceleration, displacement and strain were measured. From the test results, it is demonstrated that the CFT arch structures are capable of resisting severe ground motions and that CFT arches offer a credible alternative to reinforced concrete arches, especially in regions of high seismic intensity.
基金supported bythe National Natural Science Foundation of China(Grant No.40776053)
文摘High-pile and beam-slab quays have been widely used after several years development. They are mature enough to be one of the most important structural types of wharves in China coastal areas. In order to accommodate large tonnage vessels, wharves should be eorrstructed in deep water gradually. However, conventional high-pile and beam-slab structares are hard to meet the requirements of large deep-water wharf. According to arch＇ s stress characteristics, a new type of wharf with catenary arched longitudinal beams is presented in this paper. The new wharf structure can make full use of arch＇s overhead crossing and reinforced concrete compression resistance, improve the interval between transverse bents greatly, and decrease underwater construction quantity. Thus, the construction cost cab be reduced. Take the third phase project of the Yangshan Deep-water Port for example, comparative analysis on catenary arched longitudinal beams and conventional longitudinal beams has been made. The result shows that with the same wharf length and width, the same loads and same longitudinal beam moment, catenary arch structure can improve the interval between bents up to 28 m, decrease the nmnber of piles and underwater construction quantity.
基金National Natural Science Foundation ofChina (No.50278054) and the Fund ofScience and Technology Development ofShanghai (No.04JC14059)
文摘The wind-induced dynamic response of long-span light-weight steel arch structure of the global transportation center (GTC) of Beijing Capital International Airport was studied. A composite technique with combination of WAWS(Weighted Amplitude Wavelet Superposition) and FFT(Fast Fourier Transformation) was introduced to simulate wind velocity time series of hundreds of spatial points simultaneously. The structural shape factors of wind load was obtained from wind tunnel model test. The wind vibration factor based on structural displacement response was investigated. After comparing the computational results with wind tunnel model test data, it was found out that the two results accord with each other if wind comes from 0° direction angle, but are quite different if wind comes from 180° direction angle in the area blocked off by airport terminals. The possible reasons of this difference were analyzed. Haar wavelet was used to transform and analyze wind velocity time series and structural wind-induced dynamic responses. The relationship between exciting wind loads and structural responses was studied in time and frequency domains.
文摘This paper presents a method for isolatedly solving the normal mode of vi-bration according to the uncoupling condition of vibrations inside and outside the archplane.The finite element method for curved beam elements is adopted to analyse the dy-namic characteristics of arch structures and the calculating program is made.The resultsobtained from Apple II microcomputer are compared with those from SAP5 program byan example,and are in good agreement.
基金Supported by the National Natural Science Foundation of Chi- na （ 50975012 ） Research Fund for the Doctoral Program of Higher Education of China （ 20091102110022 ） Innovation Foundation of BUAA for PhD Graduates （YWF-12-RBYJ-015）
文摘Based on the analyses on arch and peltate venation structures, the design of reinforcing frames was improved. First, distribution rules of the arch structure were summarized. According to the load condition and the structure of the frame, a mechanical model of arch structure was devel- oped, and two solutions for the model were analyzed and compared with each other. Through the a- nalysis, application rules of arch structure for improving the design were obtained. Then, distribu- tion rules of peltate venation structure were summarized. By using the same method, application rules of peltate venation structure for improving the design were also obtained. Finally, mechanical problem of the frame was described, and rib arrangement of the frame was redesigned. A parameter optimization for the widths of ribs in bionic arrangement was also carried out to accomplish the im- proving design. Comparison between bionic and conventional reinforcing frames shows that the weight is reduced by as much as 15.3%.
基金Project 2002CB412704 supported by The National 973 Item
文摘Aimed at the frozen soil arch reinforcement form of upside shed used for the shield machine launching in tunneling the internal force of the structure was calculated with the aid of the structural mechanics theory. Considering the space characteristics of the structure, this calculating method is suitable for practical engineering. Moreover, the behavior of the freezing arch reinforcement structure was analyzed combined with an engineering case.
文摘<div style="text-align:justify;"> Arches are employed for bridges. This particular type of structures, characterized by a very old use tradition, is nowadays, widely exploited because of its strength, resilience, cost-effectiveness and charm. In recent years, a more conscious design approach that focuses on a more proper use of the building materials combined with the increasing of the computational capability of the modern computers, has led the research in the civil engineering field to the study of optimization algorithms applications aimed at the definition of the best design parameters. In this paper, a differential formulation and a MATLAB code for the calculation of the internal stresses in the arch structure are proposed. Then, the application of a machine learning algorithm, the genetic algorithm, for the calculation of the geometrical parameters, that allows to minimize the quantity of material that constitute the arch structures, is implemented. In this phase, the method used to calculate the stresses has been considered as a constraint function to reduce the range of the solutions to the only ones able to bear the design loads with the smallest volume. In particular, some case studies with different cross-sections are reported to prove the validity of the method and to compare the obtained results in terms of optimization effectiveness. </div>
