An axial symmetry finite element model coupled with electricity-thermal effect was developed to study the temperature field distribution in process of the flash butt welding （FBW） of frog highmanganese steel. The in...An axial symmetry finite element model coupled with electricity-thermal effect was developed to study the temperature field distribution in process of the flash butt welding （FBW） of frog highmanganese steel. The influence of temperature dependent material properties and the contact resistance were taken into account in FEM ＇simulation. Meanwhile, the lost materials due to .splutter was resolved by using birth and death element. The result of analyzing data shows that the moddel in the FBW flashing is reasonable and feasible, and can exactly simulate the temperature field distribution. The modeling provides reference for analysis of welding technologies on the temperature field of high-manganese steel in FBW.展开更多
Under the spirit of sustainable development, ‘lightweight’ has been gradually included into the vehicle design criterion by many manufacturers and used in automobile production. Following this trend, domestic wheel ...Under the spirit of sustainable development, ‘lightweight’ has been gradually included into the vehicle design criterion by many manufacturers and used in automobile production. Following this trend, domestic wheel suppliers also begin to study the technology of lightweight wheel. One way to achieve this goal is improving strength grade of the steel and optimizing the structure design in the field of steel wheels. But there are a few problems in flash butt welding process in the application of high strength steel, leading to high rejection rates. SW400 steel is a special high strength wheel steel developed by Benxi Steel. Taking SW400 steel as the research material, this article studys the feasibility of improving the properties of rim flash butt welded joints by adding preheating process.展开更多
The fatigue life evaluation of the girth butt weld within the welded cast steel joint was studied based on the extrapolation notch stress method.Firstly,the mesh sensitivity of the finite element model of the welded c...The fatigue life evaluation of the girth butt weld within the welded cast steel joint was studied based on the extrapolation notch stress method.Firstly,the mesh sensitivity of the finite element model of the welded cast steel joint was analyzed to determine the optimal mesh size.Based on the stress field analysis of the finite element model of the welded cast steel joint at the weld toe and weld root,the sharp model of the extrapolation notch stress method was applied to derive the effective notch stress of the rounded model belonging to the effective notch stress method,in which the key problem is to calculate the extrapolation point C,and the extrapolation point C has an exponential function relationship with the geometric parameters of the welded cast steel joint.By setting different values of geometric parameters,the corresponding value of parameter C is calculated,and then the functional relationship between the extrapolation point C and the geometric parameters can be obtained by the multiple linear regression analysis.Meanwhile,the fatigue life evaluation of the girth butt weld within welded cast steel joints based on the effective notch stress was performed according to the guideline recommended by the IIW(International Institute of Welding).The results indicate that the extrapolation notch stress method can effectively simplify the process of calculating the effective notch stress and accurately evaluate the fatigue life of the girth butt weld within welded cast steel joints.展开更多
In order to investigate the laws of variation on tensile strength of butt welded joint post high temperatures, the wide plate tension tests for butt welded joint were conducted after cooling down from different high t...In order to investigate the laws of variation on tensile strength of butt welded joint post high temperatures, the wide plate tension tests for butt welded joint were conducted after cooling down from different high temperatures. The tests indicate that specimens appear ductile fracture at the steel plate during the tension tests after cooling down. The maximum temperatures undergone and the cooling pattern are major factors influencing tensile strength of butt welded joint post high temperatures. The tensile strength mostly reduces by 8% within 900℃. Based on the experimental results, the paper proposes the calculation formulas of tensile strength of butt welded joint post high temperatures. The conclusions of the paper supply references for evaluation damage and reinforcement of steel structure post fire.展开更多
Many processes are used to join reinforcing bar (steel bar), but only a few of them, e.g. overlapping welding, gas pressure welding, thread joining, cold pressure sleeve joining, are able to be used on building sites ...Many processes are used to join reinforcing bar (steel bar), but only a few of them, e.g. overlapping welding, gas pressure welding, thread joining, cold pressure sleeve joining, are able to be used on building sites because the conditions of building sites are very particular. First, the work of joining reinforcing bar is mobile, that is to say, it must be moved from one place to another after having accomplished one joint. So it demands that the welding equipment (especially the welding head) must be convenient for moving. So it must be small and light. Second, the electricity capacity of the welding equipment can not be too large because the whole electricity capacity of a building site is limited. Third, the welding process ought to be simple because the situation og building sites is very poor and is on the open air. The more complex the process is, the more difficult the work will be. Fourth, the quality of the joint should be reliable and stable because it is impossible to check the quality of every joint, and there is no suitable way to do it even by now. For those reasons, the electroslag pressure butt welding has got great development recent years and is just suitable to be used on building sites to join vertical reinforcing bars. The article introduces its basic principle, processing, chief properties, and some test results.展开更多
This paper illustrates the construction and application of the applied computeraided .system for hotplate butt welding of plastics with regard to inquiry, imitation and Optimization.
In order to propose high effective simulation using finite element method (FEM) for predicting deformation and residual stress generated by one pass butt welding, a series of numerical analyses were carried out. By id...In order to propose high effective simulation using finite element method (FEM) for predicting deformation and residual stress generated by one pass butt welding, a series of numerical analyses were carried out. By idealizing the movement of heat source (the instantaneous heat input method), the tendency of welding out-of-plane deformation and the residual stress distribution could be predicted. The computing time was around 9% of that by the precise model with considering the movement of heat source. On the other hand, applicability of two dimensional shell elements instead of generally used three dimensional solid elements was examined. The heat input model with considering the temperature distribution in the thickness direction was proposed for the simulation by using the shell elements. It was confirmed that the welding out-of-plane deformation and residual stress could be predicted with high accuracy by the model with shell elements and the distributed heat input methods. The computing time was around 8% of that by the precise model with solid elements.展开更多
Arc pressure is the key influencing factor to forming of molten pool. Countering the characteristic of tungsten inert gas arc welding with micro gap for tantalum sheet, according to the fundament of arc physics, a dis...Arc pressure is the key influencing factor to forming of molten pool. Countering the characteristic of tungsten inert gas arc welding with micro gap for tantalum sheet, according to the fundament of arc physics, a distribution model of arc pressure and forming mechanism of molten pool with micro butt gap are proposed, and the influences of arc pressure on forming of molten pool are discussed. Experimental researches for the dynamic formation process of weld molten pool by using high-speed vidicon camera show that when butt gap is appropriate, that is from 0. 1 to 0. 15 mm, molten metals formed on two workpiece uplift and grow up first, then are fused and form uniform molten pool finally.展开更多
The fatigue properties of friction stir welded （FSW） butt joint and base metal of MB8 magnesium alloy were investigated. The comparative fatigue tests were carried out using EHF-EM2OOK2-070-IA fatigue testing machin...The fatigue properties of friction stir welded （FSW） butt joint and base metal of MB8 magnesium alloy were investigated. The comparative fatigue tests were carried out using EHF-EM2OOK2-070-IA fatigue testing machine for both FSW butt joint and base metal specimens. The fatigue fractures were observed and analyzed using a scanning electron microscope of JSM-6063LA type. The experimental results show that the fatigue performance of the FSW butt joint of MB8 magnesium alloy is sharply decreased. The conditional fatigue limit （2 x 106） of base metal and welded butt joint is about 77.44 MPa and 49. 91 MPa, respectively. The conditional fatigue limit （2 x 106 ） of the welded butt joint is 64.45% of that of base metal. The main reasons are that the welding can lead to stress concentration in the flash area, tensile welding residual stress in the welded joint（ The residual stress value was 30. 5 MPa）, as well as the grain size is not uniform in the heat-affected zone. The cleavage steps or quasi-cleavage patterns present on the fatigue fracture surface, the fracture type of the FSW butt joint belongs to a brittle fracture.展开更多
The effects of parallel and angular butt designs with different gap widths on the microstructure and mechanical properties of the resultant magnesium joints in gas tungsten arc welding were investigated. The experimen...The effects of parallel and angular butt designs with different gap widths on the microstructure and mechanical properties of the resultant magnesium joints in gas tungsten arc welding were investigated. The experimental results displayed that the tensile strength of the joint made with angular butt joint and 0.3 ram-wide gap reached 266 MPa, the joint fractured through the heat-affected zone or base metal during tensile testing, and the microstructure examination showed that no macropore appeared in the fusion zone. However, macropores in diameter of larger than 200 micron occurred for other joint designs, the tensile strength of the resultant joints decreased, and the joints fractured through the fusion zone during tensile testing. The fracture surfaces were examined by scanning electron microscopy and the microhardness distribution in the joints was measured by using a Vickers microhardness tester.展开更多
This paper presents an experimental investigation of laser welding low carbon galvanized steel in butt-joint configurations. The experimental work is focused on the effects of various laser welding parameters on the w...This paper presents an experimental investigation of laser welding low carbon galvanized steel in butt-joint configurations. The experimental work is focused on the effects of various laser welding parameters on the welds quality. The investigations are based on a structured experimental design using the Taguchi method. Welding experiments are conducted using a 3 kW Nd:YAG laser source. The selected laser welding parameters (laser power, welding speed, laser fiber diameter, gap between sheets and sheet thickness) are combined and used to evaluate the variation of four weld quality attributes (bead width, penetration depth, underfill and hardness) and to identify the possible relationship between welding parameters and weld physical and geometrical attributes. The effects of these parameters are studied using ANOVA to find their contributions to the variation of different weld characteristics. Plots of the main effects and the interaction effects are also used to understand the influence of the welding parameters. The results reveal that all welding parameters are relevant to bead width (BDW) and depth of penetration (DOP) with a relative predominance of laser power and welding speed. The effect of laser fiber diameter on penetration depth is insignificant. Typical gap-dependent weld shapes show that a small gap results in a narrower and deeper weld. Due to the standard sheared edge, an underfill between 5% and 10% occurs for no-gap experiments. The resulting hardness values are relatively similar for all the experimental tests.展开更多
文摘An axial symmetry finite element model coupled with electricity-thermal effect was developed to study the temperature field distribution in process of the flash butt welding （FBW） of frog highmanganese steel. The influence of temperature dependent material properties and the contact resistance were taken into account in FEM ＇simulation. Meanwhile, the lost materials due to .splutter was resolved by using birth and death element. The result of analyzing data shows that the moddel in the FBW flashing is reasonable and feasible, and can exactly simulate the temperature field distribution. The modeling provides reference for analysis of welding technologies on the temperature field of high-manganese steel in FBW.
基金supported by the Key Science and Technology of Jilin Province(Grant No.20140204070GX)
文摘Under the spirit of sustainable development, ‘lightweight’ has been gradually included into the vehicle design criterion by many manufacturers and used in automobile production. Following this trend, domestic wheel suppliers also begin to study the technology of lightweight wheel. One way to achieve this goal is improving strength grade of the steel and optimizing the structure design in the field of steel wheels. But there are a few problems in flash butt welding process in the application of high strength steel, leading to high rejection rates. SW400 steel is a special high strength wheel steel developed by Benxi Steel. Taking SW400 steel as the research material, this article studys the feasibility of improving the properties of rim flash butt welded joints by adding preheating process.
基金The National Key Research and Development Program of China(No.2017YFC0805100),the National Natural Science Foundation of China(No.51578137)the Priority Academic Program Development of Jiangsu Higher Education Institutions,the Open Research Fund Program of Jiangsu Key Laboratory of Engineering Mechanics.
文摘The fatigue life evaluation of the girth butt weld within the welded cast steel joint was studied based on the extrapolation notch stress method.Firstly,the mesh sensitivity of the finite element model of the welded cast steel joint was analyzed to determine the optimal mesh size.Based on the stress field analysis of the finite element model of the welded cast steel joint at the weld toe and weld root,the sharp model of the extrapolation notch stress method was applied to derive the effective notch stress of the rounded model belonging to the effective notch stress method,in which the key problem is to calculate the extrapolation point C,and the extrapolation point C has an exponential function relationship with the geometric parameters of the welded cast steel joint.By setting different values of geometric parameters,the corresponding value of parameter C is calculated,and then the functional relationship between the extrapolation point C and the geometric parameters can be obtained by the multiple linear regression analysis.Meanwhile,the fatigue life evaluation of the girth butt weld within welded cast steel joints based on the effective notch stress was performed according to the guideline recommended by the IIW(International Institute of Welding).The results indicate that the extrapolation notch stress method can effectively simplify the process of calculating the effective notch stress and accurately evaluate the fatigue life of the girth butt weld within welded cast steel joints.
文摘In order to investigate the laws of variation on tensile strength of butt welded joint post high temperatures, the wide plate tension tests for butt welded joint were conducted after cooling down from different high temperatures. The tests indicate that specimens appear ductile fracture at the steel plate during the tension tests after cooling down. The maximum temperatures undergone and the cooling pattern are major factors influencing tensile strength of butt welded joint post high temperatures. The tensile strength mostly reduces by 8% within 900℃. Based on the experimental results, the paper proposes the calculation formulas of tensile strength of butt welded joint post high temperatures. The conclusions of the paper supply references for evaluation damage and reinforcement of steel structure post fire.
文摘Many processes are used to join reinforcing bar (steel bar), but only a few of them, e.g. overlapping welding, gas pressure welding, thread joining, cold pressure sleeve joining, are able to be used on building sites because the conditions of building sites are very particular. First, the work of joining reinforcing bar is mobile, that is to say, it must be moved from one place to another after having accomplished one joint. So it demands that the welding equipment (especially the welding head) must be convenient for moving. So it must be small and light. Second, the electricity capacity of the welding equipment can not be too large because the whole electricity capacity of a building site is limited. Third, the welding process ought to be simple because the situation og building sites is very poor and is on the open air. The more complex the process is, the more difficult the work will be. Fourth, the quality of the joint should be reliable and stable because it is impossible to check the quality of every joint, and there is no suitable way to do it even by now. For those reasons, the electroslag pressure butt welding has got great development recent years and is just suitable to be used on building sites to join vertical reinforcing bars. The article introduces its basic principle, processing, chief properties, and some test results.
文摘This paper illustrates the construction and application of the applied computeraided .system for hotplate butt welding of plastics with regard to inquiry, imitation and Optimization.
文摘In order to propose high effective simulation using finite element method (FEM) for predicting deformation and residual stress generated by one pass butt welding, a series of numerical analyses were carried out. By idealizing the movement of heat source (the instantaneous heat input method), the tendency of welding out-of-plane deformation and the residual stress distribution could be predicted. The computing time was around 9% of that by the precise model with considering the movement of heat source. On the other hand, applicability of two dimensional shell elements instead of generally used three dimensional solid elements was examined. The heat input model with considering the temperature distribution in the thickness direction was proposed for the simulation by using the shell elements. It was confirmed that the welding out-of-plane deformation and residual stress could be predicted with high accuracy by the model with shell elements and the distributed heat input methods. The computing time was around 8% of that by the precise model with solid elements.
文摘Arc pressure is the key influencing factor to forming of molten pool. Countering the characteristic of tungsten inert gas arc welding with micro gap for tantalum sheet, according to the fundament of arc physics, a distribution model of arc pressure and forming mechanism of molten pool with micro butt gap are proposed, and the influences of arc pressure on forming of molten pool are discussed. Experimental researches for the dynamic formation process of weld molten pool by using high-speed vidicon camera show that when butt gap is appropriate, that is from 0. 1 to 0. 15 mm, molten metals formed on two workpiece uplift and grow up first, then are fused and form uniform molten pool finally.
基金supported by the National Natural Science Foundation(No.51265013)the Natural Science Foundation of Jiangxi Province(No.20151BAB206007)
文摘The fatigue properties of friction stir welded （FSW） butt joint and base metal of MB8 magnesium alloy were investigated. The comparative fatigue tests were carried out using EHF-EM2OOK2-070-IA fatigue testing machine for both FSW butt joint and base metal specimens. The fatigue fractures were observed and analyzed using a scanning electron microscope of JSM-6063LA type. The experimental results show that the fatigue performance of the FSW butt joint of MB8 magnesium alloy is sharply decreased. The conditional fatigue limit （2 x 106） of base metal and welded butt joint is about 77.44 MPa and 49. 91 MPa, respectively. The conditional fatigue limit （2 x 106 ） of the welded butt joint is 64.45% of that of base metal. The main reasons are that the welding can lead to stress concentration in the flash area, tensile welding residual stress in the welded joint（ The residual stress value was 30. 5 MPa）, as well as the grain size is not uniform in the heat-affected zone. The cleavage steps or quasi-cleavage patterns present on the fatigue fracture surface, the fracture type of the FSW butt joint belongs to a brittle fracture.
基金supported by the State Key Lab of Advanced Welding and Joining,Harbin Institute of Technology (Project No.09009)
文摘The effects of parallel and angular butt designs with different gap widths on the microstructure and mechanical properties of the resultant magnesium joints in gas tungsten arc welding were investigated. The experimental results displayed that the tensile strength of the joint made with angular butt joint and 0.3 ram-wide gap reached 266 MPa, the joint fractured through the heat-affected zone or base metal during tensile testing, and the microstructure examination showed that no macropore appeared in the fusion zone. However, macropores in diameter of larger than 200 micron occurred for other joint designs, the tensile strength of the resultant joints decreased, and the joints fractured through the fusion zone during tensile testing. The fracture surfaces were examined by scanning electron microscopy and the microhardness distribution in the joints was measured by using a Vickers microhardness tester.
文摘This paper presents an experimental investigation of laser welding low carbon galvanized steel in butt-joint configurations. The experimental work is focused on the effects of various laser welding parameters on the welds quality. The investigations are based on a structured experimental design using the Taguchi method. Welding experiments are conducted using a 3 kW Nd:YAG laser source. The selected laser welding parameters (laser power, welding speed, laser fiber diameter, gap between sheets and sheet thickness) are combined and used to evaluate the variation of four weld quality attributes (bead width, penetration depth, underfill and hardness) and to identify the possible relationship between welding parameters and weld physical and geometrical attributes. The effects of these parameters are studied using ANOVA to find their contributions to the variation of different weld characteristics. Plots of the main effects and the interaction effects are also used to understand the influence of the welding parameters. The results reveal that all welding parameters are relevant to bead width (BDW) and depth of penetration (DOP) with a relative predominance of laser power and welding speed. The effect of laser fiber diameter on penetration depth is insignificant. Typical gap-dependent weld shapes show that a small gap results in a narrower and deeper weld. Due to the standard sheared edge, an underfill between 5% and 10% occurs for no-gap experiments. The resulting hardness values are relatively similar for all the experimental tests.
