Bit-Interleaved Coded Modulation with Iterative Decoding (BICM-ID) is a bandwidth ef- ficient transmission, where the bit error rate is reduced through the iterative information exchange between the inner demapper and...Bit-Interleaved Coded Modulation with Iterative Decoding (BICM-ID) is a bandwidth ef- ficient transmission, where the bit error rate is reduced through the iterative information exchange between the inner demapper and the outer decoder. The choice of the symbol mapping is the crucial design parameter. This paper indicates that the Harmonic Mean of the Minimum Squared Euclidean (HMMSE) distance is the best criterion for the mapping design. Based on the design criterion of the HMMSE distance, a new search algorithm to find the optimized labeling maps for BICM-ID system is proposed. Numerical results and performance comparison show that the new labeling search method has a low complexity and outperforms other labeling schemes using other design criterion in BICM-ID system, therefore it is an optimized labeling method.展开更多
We study the impact of various modulation mapping strategies and signal constellation shapes on the se- crecy rates achievable with bit-interleaved coded modulation （BICM） schemes. Transmission over an ergodic Rayle...We study the impact of various modulation mapping strategies and signal constellation shapes on the se- crecy rates achievable with bit-interleaved coded modulation （BICM） schemes. Transmission over an ergodic Rayleigh fading channel is assumed throughout this work. Various constellations and mapping techniques are considered in this work to maximize the capacity difference between the main channel and the eavesdropper channel, rather than to opti- mize the capacity of both channels. We show that in terms of achievable secrecy rate, Gray and Quasi-Gray mappings only perform Well at low SNR but outperformed by other mapping techniques when SNR increases. The proper design of signal mapping can significantly enhance the achievable secrecy rate in BICM schemes. It is indicated that the key parameter to the secrecy rate of a BICM system is the distance spectrum of Euclidean distances for mappings.展开更多
The demodulation and decoding solution commonly used in the bit interleaving code modulation and the LDPC coded demodulation and decoding system of the iterative decoding （BICM-ID） is to report the soft information ...The demodulation and decoding solution commonly used in the bit interleaving code modulation and the LDPC coded demodulation and decoding system of the iterative decoding （BICM-ID） is to report the soft information output from the decoder of the receiver to the demodulator as priori information for completing the decoding. However, this will give rise to the reduction of the minimum Euclidean distances between codes, so that the performances of the system decline under non-fading Gaussian channel. According to this problem, an optimized iterative demodulation decoding solution is proposed and also is analyzed using simulation. The result shows that this solution can improve the demodulation and decoding performances of LDPC coded modulation and demodulation system.展开更多
Iterative demodulation and decoding scheme is analyzed and modulation labeling is considered to be one of the crucial factors to this scheme. By analyzing the existent mapping design criterion, four aspects are found ...Iterative demodulation and decoding scheme is analyzed and modulation labeling is considered to be one of the crucial factors to this scheme. By analyzing the existent mapping design criterion, four aspects are found as the key techniques for choosing a label mapping. Based on this discovery, a novel mapping design criteflon is proposed and two label mappings are searched according to it. Simulation results show that the performance of BICM-ID using the novel mappings is better than the former ones. The extrinsic information transfer （EXIT） chart is introduced and it is used to evaluate the proposed mapping design criteria.展开更多
Realtime speech communications require high efficient compression algorithms to encode speech signals. As the compressed speech parameters are highly sensitive to transmission errors, robust source and channel decodin...Realtime speech communications require high efficient compression algorithms to encode speech signals. As the compressed speech parameters are highly sensitive to transmission errors, robust source and channel decoding and demodulation schemes are both important and of practical use. In this paper, an it- erative joint souree-channel decoding and demodulation algorithm is proposed for mixed excited linear pre- diction （MELP） vocoder by both exploiting the residual redundancy and passing soft information through- out the receiver while introducing systematic global iteration process to further enhance the performance. Being fully compatible with existing transmitter structure, the proposed algorithm does not introduce addi- tional bandwidth expansion and transmission delay. Simulations show substantial error correcting perfor- mance and synthesized speech quality improvement over conventional separate designed systems in delay and bandwidth constraint channels by using the joint source-channel decoding and demodulation （JSCCM） algorithm.展开更多
Mapping design criteria of bit-interleaved coded modulation with iterative decoding (BICM-ID) with square 16QAM are analyzed. Three of the existing criteria are analyzed and compared with each other. Through the compa...Mapping design criteria of bit-interleaved coded modulation with iterative decoding (BICM-ID) with square 16QAM are analyzed. Three of the existing criteria are analyzed and compared with each other. Through the comparison, two main characters of the mapping design criteria are found. They are the harmonic mean of the minimum squared Euclidean distance and the average of Hamming distances with the nearest Euclidean distance. Based on these two characters, a novel mapping design criterion is proposed and a label mapping named mixed mapping is searched according to it. Simulation results show that mixed mapping performs better than the other mappings in BICM-ID system.展开更多
The 16-ary quadrature amplitude modulation （16QAM） is a high spectral efficient scheme for high-speed transmission systems. To remove the phase ambiguity in the coherent detection system, differential-encoded 16QAM ...The 16-ary quadrature amplitude modulation （16QAM） is a high spectral efficient scheme for high-speed transmission systems. To remove the phase ambiguity in the coherent detection system, differential-encoded 16QAM （DE-16QAM） is usually used, however, it will cause performance degradation about 3 dB as compared to the conventional 16QAM. To overcome the performance loss, a serial concatenated system with outer low density parity check （LDPC） codes and inner DE-16QAM is proposed. At the receiver, joint iterative differential demodulation and decoding （ID） is carried out to approach the maximum likelihood performance. Moreover, a genetic evolution algorithm based on the extrinsic information transfer chart is proposed to optimize the degree distribution of the outer LDPC codes. Both theoretical analyses and simulation results indicate that this algorithm not only compensates the performance loss, but also obtains a significant performance gain, which is up to 1 dB as compared to the conventional non-DE-16QAM.展开更多
It is well known that turbo decoding always begins from the first component decoder and supposes that the apriori information is '0' at the first iterative decoding. To alternatively start decoding at two comp...It is well known that turbo decoding always begins from the first component decoder and supposes that the apriori information is '0' at the first iterative decoding. To alternatively start decoding at two component decoders, we can gain two soft output values for the received observation of an input bit. It is obvious that two soft output values comprise more sufficient extrinsic information than only one output value obtained in the conventional scheme since different start points of decoding result in different combinations of the a priori information and the input codewords with different symbol orders due to the permutation of an interleaver. Summarizing two soft output values for erery bit before making hard decisions, we can correct more errors due to their complement. Consequently, turbo codes can achieve better error correcting performance than before in this way. Simulation results show that the performance of turbo codes using the novel proposed decoding scheme can get a growing improvement with the increment of SNR in general compared to the conventional scheme. When the bit error probability is 10-5 , the proposed scheme can achieve 0.5 dB asymptotic coding gain or so under the given simulation conditions.展开更多
Applications on iterative control and multiple input multiple output (MIMO) system were developed. Two new charts derived from extrinsic information transfer (EXIT) chart were employed as the designing tools, which ar...Applications on iterative control and multiple input multiple output (MIMO) system were developed. Two new charts derived from extrinsic information transfer (EXIT) chart were employed as the designing tools, which are called as output mutual information chart with defined iterative degree (DID) chart and near optimum output mutual information (NOMI) chart respectively. Different from the EXIT chart, they can show the iterative performance on the whole signal-to-noise ratio range with one single curve, whereas computation complexity is greatly reduced compared with conventional bit error ratio (BER) performance curve. The iterative control was implemented according to a near-optimum iterative degree vector determined by NOMI chart, the reasonability of uncertain parameters was analyzed in one MIMO system. The concepts were illustrated based on bit-interleaved coded modulation with iterative decoding (BICM-ID).展开更多
In this paper, a new method to approximate the compensation term in the Jacobian logarithm used by the MAP decoder is proposed. Using the proposed approximation, the complex functions In（.） and exp（.） in the Exact...In this paper, a new method to approximate the compensation term in the Jacobian logarithm used by the MAP decoder is proposed. Using the proposed approximation, the complex functions In（.） and exp（.） in the Exact-log-MAP algorithm can be estimated with high accuracy and lower computational complexity. The efficacy of the proposed approximation is investigated and demonstrated by applying it to iteratively decoded BICM （Bit Interleaved Coded Modulation）.展开更多
This paper proposes a novel mapping scheme for bit-interleaved coded modulation with iterative decoding(BICM-ID).The symbol mapping is composed of two QPSK with different radiuses and phases,called cross equalization-...This paper proposes a novel mapping scheme for bit-interleaved coded modulation with iterative decoding(BICM-ID).The symbol mapping is composed of two QPSK with different radiuses and phases,called cross equalization-8PSK-quasi-semi set partitioning(CE-8PSK-Quasi-SSP).Providing the same average power,the proposed scheme can increase the minimum squared Euclidean distance(MSED)and then improve the receiving performance of BICM-ID compared with conventional symbol mapping schemes.Simultaneously,a modified iteration decoding algorithm is proposed in this paper.In the process of iteration decoding,different proportion of the extrinsic information to the systematic observations results in distinct decoding performance.At high SNR(4~9dB),the observation information plays a more important role than the extrinsic information.Simulation results show that the proportion set at 1.2 is more suitable for the novel mapping in BICM-ID.When the BER is 10^(-4),more than 0.9dB coding gain over Rayleigh channels can be achieved for the improved mapping and decoding scheme.展开更多
Bit-interleaved coded modulation (BICM) is suitable to bandwidth-efficient communication systems. Hybrid automatic repeat request (HARQ) can provide more reliability to high-speed wireless data transmission. A new pat...Bit-interleaved coded modulation (BICM) is suitable to bandwidth-efficient communication systems. Hybrid automatic repeat request (HARQ) can provide more reliability to high-speed wireless data transmission. A new path weight complementary convolutional (PWCC) code used in the type-Ⅱ BICM-HARQ system is proposed. The PWCC code is composed of the original code and the complimentary code. The path in trellis with large hamming weight of the complimentary code is designed to compensate for the path in trellis with small hamming weight of the original code. Hence, both of the original code and the complimentary code can achieve the performance of the good code criterion of corresponding code rate. The throughput efficiency of the BICM-HARQ system wit PWCC code is higher than repeat code system, a little higher than puncture code system in low signal-to-noise ratio (SNR) values and much higher than puncture code system, the same as repeat code system in high SNR values. These results are confirmed by the simulation.展开更多
为了研究Polar码在编码调制(CM)系统中的性能,提出了一种基于Polar码的比特交织编码调制(BICM)系统.分析了高斯白噪声(AWGN)信道中不同调制方式对系统误比特率(BER)性能的影响,并将所提系统的BER性能与基于低密度奇偶校验(LDPC)码的BIC...为了研究Polar码在编码调制(CM)系统中的性能,提出了一种基于Polar码的比特交织编码调制(BICM)系统.分析了高斯白噪声(AWGN)信道中不同调制方式对系统误比特率(BER)性能的影响,并将所提系统的BER性能与基于低密度奇偶校验(LDPC)码的BICM系统性能进行了对比.仿真结果表明,在QPSK调制下,基于Polar码的BICM系统与基于Polar码的无编码调制系统的BER曲线几乎完全重合;而在16QAM调制下,当码长较大时,基于Polar码的BICM系统较基于Polar码的无编码调制系统最大节省0.8 d B的比特信噪比.当信道编码码长为1 024、码率为0.5时,在中高比特信噪比区域上,基于Polar码的BICM系统可比基于LDPC码的BICM系统获得至少2 d B的比特信噪比增益.展开更多
基金Supported by the National Natural Science Foundation of China (No.60472104).
文摘Bit-Interleaved Coded Modulation with Iterative Decoding (BICM-ID) is a bandwidth ef- ficient transmission, where the bit error rate is reduced through the iterative information exchange between the inner demapper and the outer decoder. The choice of the symbol mapping is the crucial design parameter. This paper indicates that the Harmonic Mean of the Minimum Squared Euclidean (HMMSE) distance is the best criterion for the mapping design. Based on the design criterion of the HMMSE distance, a new search algorithm to find the optimized labeling maps for BICM-ID system is proposed. Numerical results and performance comparison show that the new labeling search method has a low complexity and outperforms other labeling schemes using other design criterion in BICM-ID system, therefore it is an optimized labeling method.
文摘We study the impact of various modulation mapping strategies and signal constellation shapes on the se- crecy rates achievable with bit-interleaved coded modulation （BICM） schemes. Transmission over an ergodic Rayleigh fading channel is assumed throughout this work. Various constellations and mapping techniques are considered in this work to maximize the capacity difference between the main channel and the eavesdropper channel, rather than to opti- mize the capacity of both channels. We show that in terms of achievable secrecy rate, Gray and Quasi-Gray mappings only perform Well at low SNR but outperformed by other mapping techniques when SNR increases. The proper design of signal mapping can significantly enhance the achievable secrecy rate in BICM schemes. It is indicated that the key parameter to the secrecy rate of a BICM system is the distance spectrum of Euclidean distances for mappings.
文摘The demodulation and decoding solution commonly used in the bit interleaving code modulation and the LDPC coded demodulation and decoding system of the iterative decoding （BICM-ID） is to report the soft information output from the decoder of the receiver to the demodulator as priori information for completing the decoding. However, this will give rise to the reduction of the minimum Euclidean distances between codes, so that the performances of the system decline under non-fading Gaussian channel. According to this problem, an optimized iterative demodulation decoding solution is proposed and also is analyzed using simulation. The result shows that this solution can improve the demodulation and decoding performances of LDPC coded modulation and demodulation system.
文摘Iterative demodulation and decoding scheme is analyzed and modulation labeling is considered to be one of the crucial factors to this scheme. By analyzing the existent mapping design criterion, four aspects are found as the key techniques for choosing a label mapping. Based on this discovery, a novel mapping design criteflon is proposed and two label mappings are searched according to it. Simulation results show that the performance of BICM-ID using the novel mappings is better than the former ones. The extrinsic information transfer （EXIT） chart is introduced and it is used to evaluate the proposed mapping design criteria.
基金Supported by the National Natural Science Foundation of China （No. 60572081 ）
文摘Realtime speech communications require high efficient compression algorithms to encode speech signals. As the compressed speech parameters are highly sensitive to transmission errors, robust source and channel decoding and demodulation schemes are both important and of practical use. In this paper, an it- erative joint souree-channel decoding and demodulation algorithm is proposed for mixed excited linear pre- diction （MELP） vocoder by both exploiting the residual redundancy and passing soft information through- out the receiver while introducing systematic global iteration process to further enhance the performance. Being fully compatible with existing transmitter structure, the proposed algorithm does not introduce addi- tional bandwidth expansion and transmission delay. Simulations show substantial error correcting perfor- mance and synthesized speech quality improvement over conventional separate designed systems in delay and bandwidth constraint channels by using the joint source-channel decoding and demodulation （JSCCM） algorithm.
文摘Mapping design criteria of bit-interleaved coded modulation with iterative decoding (BICM-ID) with square 16QAM are analyzed. Three of the existing criteria are analyzed and compared with each other. Through the comparison, two main characters of the mapping design criteria are found. They are the harmonic mean of the minimum squared Euclidean distance and the average of Hamming distances with the nearest Euclidean distance. Based on these two characters, a novel mapping design criterion is proposed and a label mapping named mixed mapping is searched according to it. Simulation results show that mixed mapping performs better than the other mappings in BICM-ID system.
基金supported by the National Natural Science Foundation of China(61171101)the State Major Science and Technology Special Projects(2009ZX03003-011-03)
文摘The 16-ary quadrature amplitude modulation （16QAM） is a high spectral efficient scheme for high-speed transmission systems. To remove the phase ambiguity in the coherent detection system, differential-encoded 16QAM （DE-16QAM） is usually used, however, it will cause performance degradation about 3 dB as compared to the conventional 16QAM. To overcome the performance loss, a serial concatenated system with outer low density parity check （LDPC） codes and inner DE-16QAM is proposed. At the receiver, joint iterative differential demodulation and decoding （ID） is carried out to approach the maximum likelihood performance. Moreover, a genetic evolution algorithm based on the extrinsic information transfer chart is proposed to optimize the degree distribution of the outer LDPC codes. Both theoretical analyses and simulation results indicate that this algorithm not only compensates the performance loss, but also obtains a significant performance gain, which is up to 1 dB as compared to the conventional non-DE-16QAM.
文摘It is well known that turbo decoding always begins from the first component decoder and supposes that the apriori information is '0' at the first iterative decoding. To alternatively start decoding at two component decoders, we can gain two soft output values for the received observation of an input bit. It is obvious that two soft output values comprise more sufficient extrinsic information than only one output value obtained in the conventional scheme since different start points of decoding result in different combinations of the a priori information and the input codewords with different symbol orders due to the permutation of an interleaver. Summarizing two soft output values for erery bit before making hard decisions, we can correct more errors due to their complement. Consequently, turbo codes can achieve better error correcting performance than before in this way. Simulation results show that the performance of turbo codes using the novel proposed decoding scheme can get a growing improvement with the increment of SNR in general compared to the conventional scheme. When the bit error probability is 10-5 , the proposed scheme can achieve 0.5 dB asymptotic coding gain or so under the given simulation conditions.
基金The National Natural Science Foundation of China (No. 60496316) The National Hi-Tech Research and Development Program (863) of China (No. 2006AA01Z270)
文摘Applications on iterative control and multiple input multiple output (MIMO) system were developed. Two new charts derived from extrinsic information transfer (EXIT) chart were employed as the designing tools, which are called as output mutual information chart with defined iterative degree (DID) chart and near optimum output mutual information (NOMI) chart respectively. Different from the EXIT chart, they can show the iterative performance on the whole signal-to-noise ratio range with one single curve, whereas computation complexity is greatly reduced compared with conventional bit error ratio (BER) performance curve. The iterative control was implemented according to a near-optimum iterative degree vector determined by NOMI chart, the reasonability of uncertain parameters was analyzed in one MIMO system. The concepts were illustrated based on bit-interleaved coded modulation with iterative decoding (BICM-ID).
文摘In this paper, a new method to approximate the compensation term in the Jacobian logarithm used by the MAP decoder is proposed. Using the proposed approximation, the complex functions In（.） and exp（.） in the Exact-log-MAP algorithm can be estimated with high accuracy and lower computational complexity. The efficacy of the proposed approximation is investigated and demonstrated by applying it to iteratively decoded BICM （Bit Interleaved Coded Modulation）.
基金Supported by the Key Project of Chinese Ministry of Education(No.106042)the Scientific Research Foundation for the Returned Overseas Chinese Scholars,State Education Ministry(2007[24])
文摘This paper proposes a novel mapping scheme for bit-interleaved coded modulation with iterative decoding(BICM-ID).The symbol mapping is composed of two QPSK with different radiuses and phases,called cross equalization-8PSK-quasi-semi set partitioning(CE-8PSK-Quasi-SSP).Providing the same average power,the proposed scheme can increase the minimum squared Euclidean distance(MSED)and then improve the receiving performance of BICM-ID compared with conventional symbol mapping schemes.Simultaneously,a modified iteration decoding algorithm is proposed in this paper.In the process of iteration decoding,different proportion of the extrinsic information to the systematic observations results in distinct decoding performance.At high SNR(4~9dB),the observation information plays a more important role than the extrinsic information.Simulation results show that the proportion set at 1.2 is more suitable for the novel mapping in BICM-ID.When the BER is 10^(-4),more than 0.9dB coding gain over Rayleigh channels can be achieved for the improved mapping and decoding scheme.
基金the National Natural Science Foundation of China(Nos. 60302006 and 60462002)
文摘Bit-interleaved coded modulation (BICM) is suitable to bandwidth-efficient communication systems. Hybrid automatic repeat request (HARQ) can provide more reliability to high-speed wireless data transmission. A new path weight complementary convolutional (PWCC) code used in the type-Ⅱ BICM-HARQ system is proposed. The PWCC code is composed of the original code and the complimentary code. The path in trellis with large hamming weight of the complimentary code is designed to compensate for the path in trellis with small hamming weight of the original code. Hence, both of the original code and the complimentary code can achieve the performance of the good code criterion of corresponding code rate. The throughput efficiency of the BICM-HARQ system wit PWCC code is higher than repeat code system, a little higher than puncture code system in low signal-to-noise ratio (SNR) values and much higher than puncture code system, the same as repeat code system in high SNR values. These results are confirmed by the simulation.
文摘为了研究Polar码在编码调制(CM)系统中的性能,提出了一种基于Polar码的比特交织编码调制(BICM)系统.分析了高斯白噪声(AWGN)信道中不同调制方式对系统误比特率(BER)性能的影响,并将所提系统的BER性能与基于低密度奇偶校验(LDPC)码的BICM系统性能进行了对比.仿真结果表明,在QPSK调制下,基于Polar码的BICM系统与基于Polar码的无编码调制系统的BER曲线几乎完全重合;而在16QAM调制下,当码长较大时,基于Polar码的BICM系统较基于Polar码的无编码调制系统最大节省0.8 d B的比特信噪比.当信道编码码长为1 024、码率为0.5时,在中高比特信噪比区域上,基于Polar码的BICM系统可比基于LDPC码的BICM系统获得至少2 d B的比特信噪比增益.
