This article presents a micro-macro unified model for predicting the deformation of metal matrix composites （MMCs）. A macro-scale model is developed to obtain the proper boundary conditions for the micro-scale model...This article presents a micro-macro unified model for predicting the deformation of metal matrix composites （MMCs）. A macro-scale model is developed to obtain the proper boundary conditions for the micro-scale model, which is used to assess the microstructural deformation of materials. The usage of the submodel technique in the analysis makes it possible to shed light on the stress and strain field at the microlevel. This is helpful to investigate the linkage between the microscopic and the macroscopic flow behavior of the composites. An iterative procedure is also proposed to find out the optimum parameters. The results show that the convergence can be attained after three iterations in computation. In order to demonstrate the reliability of mi- cro-macro unified model, results based on the continuum composite model are also investigated using the stress-strain relation of composite obtained from the iterations. By comparing the proposed unified model to the continuum composite model, it is clear that the former exhibits large plastic deformation in the case of little macroscopic deformation, and the stresses and strains obtained from the submodel are higher than those from the macroscopic deformation.展开更多
Oxidation behavior of C/C-SiC gradient matrix composites and C/C composites were compared in stationary air. The results show that oxidation threshold of C-SiC materials increases with the amount of SiC particles in t...Oxidation behavior of C/C-SiC gradient matrix composites and C/C composites were compared in stationary air. The results show that oxidation threshold of C-SiC materials increases with the amount of SiC particles in the codeposition matrix. Oxidation rate of C/C-SiC gradient matrix composites is significantly lower than that of C/C material. The micro-oxidation process was observed by SEM.展开更多
The microstructure and rheological behavior of semi-solid Mg2Si/AM60 magnesium matrix composite at steady state were investigated.The results show that the primary α-Mg phases are knapped by mechanical stirring and t...The microstructure and rheological behavior of semi-solid Mg2Si/AM60 magnesium matrix composite at steady state were investigated.The results show that the primary α-Mg phases are knapped by mechanical stirring and the Chinese script type reinforced Mg2Si phases exist in liquid phase and grain boundary.The analysis of apparent viscosity indicates that the apparent viscosity of semi-solid Mg2Si/AM60 magnesium matrix composite at steady state increases with increasing the volume fraction of Mg2Si and solid fraction of primary α-Mg,but decreases with increasing the shearing rate and shearing time,and the apparent viscosity keeps stable when shearing time reaches 300 s.展开更多
The interfacial microstructure and tensile properties of the squeeze cast SiCw/AZ91 Mg composites were characterized. There exist uniform, line and discrete MgO particles at the interface between SiC whisker and magn...The interfacial microstructure and tensile properties of the squeeze cast SiCw/AZ91 Mg composites were characterized. There exist uniform, line and discrete MgO particles at the interface between SiC whisker and magnesium in the composites using acid aluminum phosphate binder. The interfacial reaction products MgO are beneficial to interfacial bonding between SiCw and the Mg matrix. resulting in an improvement of the mechanical properties of the composite.展开更多
In order to improve wear resistance and decrease the cost, carbon and carbon nanotubes reinforced copper matrix composites were fabricated by the power metallurgy method. The effects of carbon （carbon and carbon nano...In order to improve wear resistance and decrease the cost, carbon and carbon nanotubes reinforced copper matrix composites were fabricated by the power metallurgy method. The effects of carbon （carbon and carbon nanotubes） volume fraction and applied load on the friction coefficient and wear rate under dry sliding of the composites were investigated at room temperature. By scanning electron microscopy （SEM）, the worn surfaces and debris were observed, and wear mechanism was also analyzed and discussed. The experimental wear process consists of the run-in, steady wear and severe wear process with the increasing of sliding distance. Both the friction coefficient and wear rate of the composites first decrease and then increase with the increasing of carbon volume fraction. The minimum friction coefficient and wear rate are obtained when carbon is 4.0vo1%. The wear mechanisms of the composites change from the adhesive wear and delamination wear to abrasive wear with the increasing of carbon volume fraction.展开更多
Compression tests on semi-solid SiCp/AZ61 magnesium matrix composites were carried out using Thermecmastor-Z dynamic material testing machine.Influences of strain-rate,strain,temperature and volume fraction of SiC par...Compression tests on semi-solid SiCp/AZ61 magnesium matrix composites were carried out using Thermecmastor-Z dynamic material testing machine.Influences of strain-rate,strain,temperature and volume fraction of SiC particles on flow stress were analyzed.The results show that the flow stress of semi-solid SiCp/AZ61 composites is sensitive to temperature and strain rate.The lower the temperature and the larger the strain rate,the higher the flow stress.Meanwhile the flow stress increases with the increase of the volume fraction of SiC particles.This study helps establish the constitutive model of magnesium matrix composites and offers theoretic and experimental references for its thixoforming.展开更多
Using large strain two dimension axisymmetric elasto plastic finite element method and the modified law of mixture, the effects of thermal residual stresses on the yielding behavior of short fiber reinforced metal mat...Using large strain two dimension axisymmetric elasto plastic finite element method and the modified law of mixture, the effects of thermal residual stresses on the yielding behavior of short fiber reinforced metal matrix composite and their dependencies on the material structure parameters (fiber volume fraction, fiber aspect ratio and fiber end distance) were studied. It is demonstrated that the stress strain partition parameter can be used to describe the stress transfer from the matrix to the fiber. The variation of the second derivation of the stress strain partition parameter can be used to determine the elastic modulus, the proportion limit, the initial and final yield strengths. In the presence of thermal residual stress, these yielding properties are asymmetric and are influenced differently by the material structure parameters under tensile and compressive loadings.展开更多
Non-interlayer liquid phase diffusion welding (China Patent) and laser welding methods for aluminum matrix composite are mainly described in this paper. In the non-interlayer liquid phase diffusion welding, the key pr...Non-interlayer liquid phase diffusion welding (China Patent) and laser welding methods for aluminum matrix composite are mainly described in this paper. In the non-interlayer liquid phase diffusion welding, the key processing parameters affecting the strength of joint is welding temperature. When temperature rises beyond solidus temperature, the bonded line vanishes. The strength of joint reaches the maximum and becomes constant when welding temperature is close to liquid phase temperature. Oxide film in the interface is no longer detected by SEM in the welded joint. With this kind of technique, particle reinforced aluminum matrix composite Al2 O3p/6061Al is welded successfully, and the joint strength is about 80% of the strength of composite (as-casted). In the laser welding, results indicate that because of the huge specific surface area of the reinforcement, the interfacial reaction between the matrix and the reinforcement is restrained intensively at certain laser power and pulsed laser beam. The laser pulse frequency directly affects the reinforcement segregation and the reinforcement distribution in the weld, so that the weldability of the composite could be improved by increasing the laser pulse frequency. The maximum strength of the weld can reach 70% of the strength of the parent.展开更多
The superplastic deformation behavior of titanium alloy matrix composites reinforced with TiB and TiC was studied. Superplastic tension tests under conditions from 750℃ to 1100℃ and initial strain rates ranging from...The superplastic deformation behavior of titanium alloy matrix composites reinforced with TiB and TiC was studied. Superplastic tension tests under conditions from 750℃ to 1100℃ and initial strain rates ranging from 2×10^-2 s^-1 to 10^-4s^-1 were carried out. A maximum elongation of 659% was obtained. The micro-structural evolution was studied by means of optical microscopy （OM） and transmission electron microcopy （TEM）. The deformation mechanism and the effect of reinforcement on superplasticity are also discussed.展开更多
A multi-inclusion cell model is used to investigate the effect of deformation temperature and whisker rotation on the hot compressive behavior of metal matrix composites with misaligned whiskers. Numerical results sho...A multi-inclusion cell model is used to investigate the effect of deformation temperature and whisker rotation on the hot compressive behavior of metal matrix composites with misaligned whiskers. Numerical results show that deformation temperature influences the work-hardening behavior of the matrix and the rotation behavior of the whiskers. With increasing temperature, the work hardening rate of the matrix decreases, but the whisker rotation angle increases. Both whisker rotation and the increase of deformation temperature can induce reductions in the load supported by whisker and the load transferred from matrix to whisker. Additionally, it is found that during large strain deformation at higher temperatures, the enhancing of deformation temperature can reduce the effect of whisker rotation. Meanwhile, the stress-strain behavior of the composite is rather sensitive to deformation temperature. At a relatively lower temperature （150℃）, the composite exhibits work hardening due to the matrix work hardening, but at relatively higher temperatures （300℃ and above）, the composite shows strain softening due to whisker rotation. It is also found that during hot compression at higher temperatures, the softening rate of the composite decreases with increasing temperature. The predicted stress-strain behavior of the composite is approximately in agreement with the experimental results.展开更多
To develop a novel method predicting the viscoelastic behavior of polymer matrix composites according to the viscoelasticity of the matrix, we used the viscoelastic model of the matrix to build new models for unidirec...To develop a novel method predicting the viscoelastic behavior of polymer matrix composites according to the viscoelasticity of the matrix, we used the viscoelastic model of the matrix to build new models for unidirectional composites in both 0° and 90° directions. Viscoelastic parameters for both new models were derived, and the obtained equations shared the same form as the viscoelastic constitutive equation of matrix material. The viscoelastic behaviors of matrix material and unidirectional composites were also tested. Results showed that fitting parameters of creep compliance equation were close to the theoretical values of viscoelastic constitutive parameters of the unidirectional composites, proving the validity of the models. A new method was obtained to predict the viscoelastic property of the unidirectional composites based on the viscoelastic property of composite matrix and elastic property of the unidirectional composites. This method provides a theoretical basis for future studies on the viscoelasticity of composite laminates.展开更多
We studied the characteristics of two-scale pore structure of preform in the deposition process and the mass transfer of reactant gas in dual-scale pores, and observed the physiochemical phenomenon associated with the...We studied the characteristics of two-scale pore structure of preform in the deposition process and the mass transfer of reactant gas in dual-scale pores, and observed the physiochemical phenomenon associated with the reaction. Thereby, we established mathematical models on two scales, respectively, preform and reactor. These models were used for the numerical simulation of the process of ceramic matrix composites densified by isothermal chemical vapor infiltration(ICVI). The models were used to carry out a systematic study on the influence of process conditions and the preform structure on the densification behaviors. The most important findings of our study are that the processing time could be reduced by about 50% without compromising the quality of the material, if the processing temperature is 950-1 000 ℃ for the first 70 hours and then raised to 1 100 ℃.展开更多
Consistency degree calculation is established on the basis of known correspondence, but in real life, the correspondence is generally unknown, so how to calculate consistency of two models under unknown correspondence...Consistency degree calculation is established on the basis of known correspondence, but in real life, the correspondence is generally unknown, so how to calculate consistency of two models under unknown correspondence has become a problem. For this condition, we should analyze unknown correspondence due to the influence of different correspondences.In this paper we obtain the relations of transitions based on event relations using branching processes, and build a behavioral matrix of relations. Based on the permutation of behavioral matrix, we express different correspondences, and define a new formula to compute the maximal consistency degree of two workflow nets. Additionally, this paper utilizes an example to show these definitions, computation as well as the advantages.展开更多
The stiffness and nanotopographical characteristics of the extracellular matrix （ECM） influence numerous developmental, physiological, and pathological processes in vivo. These biophysical cues have therefore been a...The stiffness and nanotopographical characteristics of the extracellular matrix （ECM） influence numerous developmental, physiological, and pathological processes in vivo. These biophysical cues have therefore been applied to modulate almost all aspects of cell behavior, from cell adhesion and spreading to proliferation and differentiation. Delineation of the biophysical modulation of cell behavior is critical to the rational design of new biomaterials, implants, and medical devices. The effects of stiffness and topographical cues on cell behavior have previously been reviewed, respectively; however, the interwoven effects of stiffness and nanotopographical cues on cell behavior have not been well described, despite similarities in phenotypic manifestations. Herein, we first review the effects of substrate stiffness and nanotopography on cell behavior, and then focus on intracellular transmission of the biophysical signals from integrins to nucleus. Attempts are made to connect extracellular regulation of cell behavior with the biophysical cues. We then discuss the challenges in dissecting the biophysical regulation of cell behavior and in translating the mechanistic understanding of these cues to tissue engineering and regenerative medicine.展开更多
2D carbon fiber reinforced AZ91 D matrix composites（2D-C_f/AZ91 D composites） were fabricated by liquid–solid extrusion and vacuum pressure infiltration technique（LSEVI）. In order to modify the interface between ...2D carbon fiber reinforced AZ91 D matrix composites（2D-C_f/AZ91 D composites） were fabricated by liquid–solid extrusion and vacuum pressure infiltration technique（LSEVI）. In order to modify the interface between fibers and matrix and protect the fiber, pyrolytic carbon（Py C） coating was deposited on the surface of T700 carbon fiber by chemical vapor deposition（CVD）. Microstructure observation of the composites revealed that the composites were well fabricated by LSEVI. The segregation of aluminum at fiber surface led to the formation of Mg_（17）Al_（12） precipitates at the interface. The aluminum improved the infiltration of the alloy and Py C coating protected the fibers effectively. The ultimate tensile strength of 2D-C_f/AZ91 D composites was about 400 MPa. The fracture process of 2D-C_f/AZ91 D composites was transverse fiber interface cracking–matrix transferring load–longitudinal fibers bearing load–longitudinal fibers breaking.展开更多
In this study, magnesium matrix composites reinforced with different loading of AlN particles were fabricated by the powder metallurgy technique. The microstructure, bending strength and fracture behavior of the resul...In this study, magnesium matrix composites reinforced with different loading of AlN particles were fabricated by the powder metallurgy technique. The microstructure, bending strength and fracture behavior of the resulting Mg-Al/Al N composites were investigated. It showed that the 5 wt% AlN reinforcements led to the highest densification and bending strength. The total strengthening effect of AlN particles was predicted by considering the contributions of CTE mismatch between the matrix and the particles,load bearing and Hall-Petch mechanism. The results revealed that the increase of dislocation density,the change of Mg17Al12 phase morphology, and the effective load transfer were the major strengthening contributors to the composites. The fracture of the composites altered from plastic to brittle mode with increasing reinforcement content. The regions of clustered particles in the composites were easy to be damaged under external load, and the fracture occurred mainly along grain boundaries.展开更多
Aluminum matrix composites reinforced with carbon nanotube were fabricated by a powder metallurgy method. The effects of carbon nanotube content on the relative density,the hardness,and the friction and wear behavior ...Aluminum matrix composites reinforced with carbon nanotube were fabricated by a powder metallurgy method. The effects of carbon nanotube content on the relative density,the hardness,and the friction and wear behavior of the composites under dry sliding condition were investigated using the ball(pin)-on-block tester. By scanning electron microscopy(SEM),the worn surfaces and worn chips were observed,and the wear mechanism of composites was analyzed and discussed. The results indicate that the addition to the aluminum matrix of 2.0%(mass fraction) carbon nanotube causes the increase in the Vickers hardness of about 80%. Within the range of carbon nanotubes content from 1.0% to 2.0%,both the friction coefficient and wear rate of composites decrease with the increase of carbon nanotube content. The delamination wear is the main wear mechanism for the composites.展开更多
In this note, the basic limit behaviors of the solution to Riccati equation in the extended Kalman filter as a parameter estimator for a sinusoidal signal are analytically investigated by using lira sup and lim inf in...In this note, the basic limit behaviors of the solution to Riccati equation in the extended Kalman filter as a parameter estimator for a sinusoidal signal are analytically investigated by using lira sup and lim inf in advanced calculus. We show that if the covariance matrix has a limit, then it must be a zero matrix.展开更多
基金Aeronautical Basic Science Foundation of China (03H53048)
文摘This article presents a micro-macro unified model for predicting the deformation of metal matrix composites （MMCs）. A macro-scale model is developed to obtain the proper boundary conditions for the micro-scale model, which is used to assess the microstructural deformation of materials. The usage of the submodel technique in the analysis makes it possible to shed light on the stress and strain field at the microlevel. This is helpful to investigate the linkage between the microscopic and the macroscopic flow behavior of the composites. An iterative procedure is also proposed to find out the optimum parameters. The results show that the convergence can be attained after three iterations in computation. In order to demonstrate the reliability of mi- cro-macro unified model, results based on the continuum composite model are also investigated using the stress-strain relation of composite obtained from the iterations. By comparing the proposed unified model to the continuum composite model, it is clear that the former exhibits large plastic deformation in the case of little macroscopic deformation, and the stresses and strains obtained from the submodel are higher than those from the macroscopic deformation.
文摘Oxidation behavior of C/C-SiC gradient matrix composites and C/C composites were compared in stationary air. The results show that oxidation threshold of C-SiC materials increases with the amount of SiC particles in the codeposition matrix. Oxidation rate of C/C-SiC gradient matrix composites is significantly lower than that of C/C material. The micro-oxidation process was observed by SEM.
基金Project(50765005) supported by the National Natural Science Foundation of Chinasupported by Key Laboratory of Ministry of Education for Conveyance and Equipment (East China Jiaotong University),China
文摘The microstructure and rheological behavior of semi-solid Mg2Si/AM60 magnesium matrix composite at steady state were investigated.The results show that the primary α-Mg phases are knapped by mechanical stirring and the Chinese script type reinforced Mg2Si phases exist in liquid phase and grain boundary.The analysis of apparent viscosity indicates that the apparent viscosity of semi-solid Mg2Si/AM60 magnesium matrix composite at steady state increases with increasing the volume fraction of Mg2Si and solid fraction of primary α-Mg,but decreases with increasing the shearing rate and shearing time,and the apparent viscosity keeps stable when shearing time reaches 300 s.
基金National Natllral S(tience l.'oundation of China (No. 59631080).
文摘The interfacial microstructure and tensile properties of the squeeze cast SiCw/AZ91 Mg composites were characterized. There exist uniform, line and discrete MgO particles at the interface between SiC whisker and magnesium in the composites using acid aluminum phosphate binder. The interfacial reaction products MgO are beneficial to interfacial bonding between SiCw and the Mg matrix. resulting in an improvement of the mechanical properties of the composite.
基金Funded by the National Natural Science Foundation of China (50873047)the Natural Science Foundation of Gansu Province (3ZS061-A25-039)
文摘In order to improve wear resistance and decrease the cost, carbon and carbon nanotubes reinforced copper matrix composites were fabricated by the power metallurgy method. The effects of carbon （carbon and carbon nanotubes） volume fraction and applied load on the friction coefficient and wear rate under dry sliding of the composites were investigated at room temperature. By scanning electron microscopy （SEM）, the worn surfaces and debris were observed, and wear mechanism was also analyzed and discussed. The experimental wear process consists of the run-in, steady wear and severe wear process with the increasing of sliding distance. Both the friction coefficient and wear rate of the composites first decrease and then increase with the increasing of carbon volume fraction. The minimum friction coefficient and wear rate are obtained when carbon is 4.0vo1%. The wear mechanisms of the composites change from the adhesive wear and delamination wear to abrasive wear with the increasing of carbon volume fraction.
基金Projects (50765005,50465003) supported by the National Natural Science Foundation of ChinaProject (S00875) supported by Innovative Group of Science and Technology of College of Jiangxi Province,China
文摘Compression tests on semi-solid SiCp/AZ61 magnesium matrix composites were carried out using Thermecmastor-Z dynamic material testing machine.Influences of strain-rate,strain,temperature and volume fraction of SiC particles on flow stress were analyzed.The results show that the flow stress of semi-solid SiCp/AZ61 composites is sensitive to temperature and strain rate.The lower the temperature and the larger the strain rate,the higher the flow stress.Meanwhile the flow stress increases with the increase of the volume fraction of SiC particles.This study helps establish the constitutive model of magnesium matrix composites and offers theoretic and experimental references for its thixoforming.
文摘Using large strain two dimension axisymmetric elasto plastic finite element method and the modified law of mixture, the effects of thermal residual stresses on the yielding behavior of short fiber reinforced metal matrix composite and their dependencies on the material structure parameters (fiber volume fraction, fiber aspect ratio and fiber end distance) were studied. It is demonstrated that the stress strain partition parameter can be used to describe the stress transfer from the matrix to the fiber. The variation of the second derivation of the stress strain partition parameter can be used to determine the elastic modulus, the proportion limit, the initial and final yield strengths. In the presence of thermal residual stress, these yielding properties are asymmetric and are influenced differently by the material structure parameters under tensile and compressive loadings.
基金supported by the National Natural Science Foundation of China(No.50171025)open project of foundation of National Key Laboratory of Metal Matrix Composite,Shanghai Jiaotong University
文摘Non-interlayer liquid phase diffusion welding (China Patent) and laser welding methods for aluminum matrix composite are mainly described in this paper. In the non-interlayer liquid phase diffusion welding, the key processing parameters affecting the strength of joint is welding temperature. When temperature rises beyond solidus temperature, the bonded line vanishes. The strength of joint reaches the maximum and becomes constant when welding temperature is close to liquid phase temperature. Oxide film in the interface is no longer detected by SEM in the welded joint. With this kind of technique, particle reinforced aluminum matrix composite Al2 O3p/6061Al is welded successfully, and the joint strength is about 80% of the strength of composite (as-casted). In the laser welding, results indicate that because of the huge specific surface area of the reinforcement, the interfacial reaction between the matrix and the reinforcement is restrained intensively at certain laser power and pulsed laser beam. The laser pulse frequency directly affects the reinforcement segregation and the reinforcement distribution in the weld, so that the weldability of the composite could be improved by increasing the laser pulse frequency. The maximum strength of the weld can reach 70% of the strength of the parent.
基金Shanghai RisingStar Program(B type)under Grant No.07QB14001.
文摘The superplastic deformation behavior of titanium alloy matrix composites reinforced with TiB and TiC was studied. Superplastic tension tests under conditions from 750℃ to 1100℃ and initial strain rates ranging from 2×10^-2 s^-1 to 10^-4s^-1 were carried out. A maximum elongation of 659% was obtained. The micro-structural evolution was studied by means of optical microscopy （OM） and transmission electron microcopy （TEM）. The deformation mechanism and the effect of reinforcement on superplasticity are also discussed.
基金This study was financially supported by the National Natural Science Foundation of China (No. 50071008).
文摘A multi-inclusion cell model is used to investigate the effect of deformation temperature and whisker rotation on the hot compressive behavior of metal matrix composites with misaligned whiskers. Numerical results show that deformation temperature influences the work-hardening behavior of the matrix and the rotation behavior of the whiskers. With increasing temperature, the work hardening rate of the matrix decreases, but the whisker rotation angle increases. Both whisker rotation and the increase of deformation temperature can induce reductions in the load supported by whisker and the load transferred from matrix to whisker. Additionally, it is found that during large strain deformation at higher temperatures, the enhancing of deformation temperature can reduce the effect of whisker rotation. Meanwhile, the stress-strain behavior of the composite is rather sensitive to deformation temperature. At a relatively lower temperature （150℃）, the composite exhibits work hardening due to the matrix work hardening, but at relatively higher temperatures （300℃ and above）, the composite shows strain softening due to whisker rotation. It is also found that during hot compression at higher temperatures, the softening rate of the composite decreases with increasing temperature. The predicted stress-strain behavior of the composite is approximately in agreement with the experimental results.
基金Funded by the National High-tech Research and Development Program of China(863 Program)(No.2013AA03 1306)Fundamental Research Funds for the Central Universities(No.WUT:2014-Ia-014)
文摘To develop a novel method predicting the viscoelastic behavior of polymer matrix composites according to the viscoelasticity of the matrix, we used the viscoelastic model of the matrix to build new models for unidirectional composites in both 0° and 90° directions. Viscoelastic parameters for both new models were derived, and the obtained equations shared the same form as the viscoelastic constitutive equation of matrix material. The viscoelastic behaviors of matrix material and unidirectional composites were also tested. Results showed that fitting parameters of creep compliance equation were close to the theoretical values of viscoelastic constitutive parameters of the unidirectional composites, proving the validity of the models. A new method was obtained to predict the viscoelastic property of the unidirectional composites based on the viscoelastic property of composite matrix and elastic property of the unidirectional composites. This method provides a theoretical basis for future studies on the viscoelasticity of composite laminates.
基金Funded by the National Natural Science Foundation of China(No.51472092)
文摘We studied the characteristics of two-scale pore structure of preform in the deposition process and the mass transfer of reactant gas in dual-scale pores, and observed the physiochemical phenomenon associated with the reaction. Thereby, we established mathematical models on two scales, respectively, preform and reactor. These models were used for the numerical simulation of the process of ceramic matrix composites densified by isothermal chemical vapor infiltration(ICVI). The models were used to carry out a systematic study on the influence of process conditions and the preform structure on the densification behaviors. The most important findings of our study are that the processing time could be reduced by about 50% without compromising the quality of the material, if the processing temperature is 950-1 000 ℃ for the first 70 hours and then raised to 1 100 ℃.
基金supported in part by the National Key R&D Program of China(2017YFB1001804)Shanghai Science and Technology Innovation Action Plan Project(16511100900)the National Natural Science Foundation of China(61572360)
文摘Consistency degree calculation is established on the basis of known correspondence, but in real life, the correspondence is generally unknown, so how to calculate consistency of two models under unknown correspondence has become a problem. For this condition, we should analyze unknown correspondence due to the influence of different correspondences.In this paper we obtain the relations of transitions based on event relations using branching processes, and build a behavioral matrix of relations. Based on the permutation of behavioral matrix, we express different correspondences, and define a new formula to compute the maximal consistency degree of two workflow nets. Additionally, this paper utilizes an example to show these definitions, computation as well as the advantages.
基金The authors would like to acknowledge funding support for Yong Yang from the National Science Foundation （CBET 1511759） and the National Institute of Health （NIH） （R15GM122953）, and for Kam W. Leong from NIH （HL109442, AI096305, GMl10494, and UH3 TR000505）, Guangdong Innovative and Entrepreneurial Research Team Program （2013S086）, and the Global Research Laboratory Program （Korean NSF GRL 2015032163）.
文摘The stiffness and nanotopographical characteristics of the extracellular matrix （ECM） influence numerous developmental, physiological, and pathological processes in vivo. These biophysical cues have therefore been applied to modulate almost all aspects of cell behavior, from cell adhesion and spreading to proliferation and differentiation. Delineation of the biophysical modulation of cell behavior is critical to the rational design of new biomaterials, implants, and medical devices. The effects of stiffness and topographical cues on cell behavior have previously been reviewed, respectively; however, the interwoven effects of stiffness and nanotopographical cues on cell behavior have not been well described, despite similarities in phenotypic manifestations. Herein, we first review the effects of substrate stiffness and nanotopography on cell behavior, and then focus on intracellular transmission of the biophysical signals from integrins to nucleus. Attempts are made to connect extracellular regulation of cell behavior with the biophysical cues. We then discuss the challenges in dissecting the biophysical regulation of cell behavior and in translating the mechanistic understanding of these cues to tissue engineering and regenerative medicine.
基金supported by the National Nature Science Foundation of China (Nos. 51472203, 51521061, 51575447 and 51432008)
文摘2D carbon fiber reinforced AZ91 D matrix composites（2D-C_f/AZ91 D composites） were fabricated by liquid–solid extrusion and vacuum pressure infiltration technique（LSEVI）. In order to modify the interface between fibers and matrix and protect the fiber, pyrolytic carbon（Py C） coating was deposited on the surface of T700 carbon fiber by chemical vapor deposition（CVD）. Microstructure observation of the composites revealed that the composites were well fabricated by LSEVI. The segregation of aluminum at fiber surface led to the formation of Mg_（17）Al_（12） precipitates at the interface. The aluminum improved the infiltration of the alloy and Py C coating protected the fibers effectively. The ultimate tensile strength of 2D-C_f/AZ91 D composites was about 400 MPa. The fracture process of 2D-C_f/AZ91 D composites was transverse fiber interface cracking–matrix transferring load–longitudinal fibers bearing load–longitudinal fibers breaking.
基金financially supported by the State Key Laboratory for Mechanical Behavior of Materials (No. 20151712)
文摘In this study, magnesium matrix composites reinforced with different loading of AlN particles were fabricated by the powder metallurgy technique. The microstructure, bending strength and fracture behavior of the resulting Mg-Al/Al N composites were investigated. It showed that the 5 wt% AlN reinforcements led to the highest densification and bending strength. The total strengthening effect of AlN particles was predicted by considering the contributions of CTE mismatch between the matrix and the particles,load bearing and Hall-Petch mechanism. The results revealed that the increase of dislocation density,the change of Mg17Al12 phase morphology, and the effective load transfer were the major strengthening contributors to the composites. The fracture of the composites altered from plastic to brittle mode with increasing reinforcement content. The regions of clustered particles in the composites were easy to be damaged under external load, and the fracture occurred mainly along grain boundaries.
基金Project(3ZS061-A25-039) supported by the Natural Science Foundation of Gansu Province, China
文摘Aluminum matrix composites reinforced with carbon nanotube were fabricated by a powder metallurgy method. The effects of carbon nanotube content on the relative density,the hardness,and the friction and wear behavior of the composites under dry sliding condition were investigated using the ball(pin)-on-block tester. By scanning electron microscopy(SEM),the worn surfaces and worn chips were observed,and the wear mechanism of composites was analyzed and discussed. The results indicate that the addition to the aluminum matrix of 2.0%(mass fraction) carbon nanotube causes the increase in the Vickers hardness of about 80%. Within the range of carbon nanotubes content from 1.0% to 2.0%,both the friction coefficient and wear rate of composites decrease with the increase of carbon nanotube content. The delamination wear is the main wear mechanism for the composites.
基金This work was supported by the National Natural Science Foundation of China （No. 61374084）.
文摘In this note, the basic limit behaviors of the solution to Riccati equation in the extended Kalman filter as a parameter estimator for a sinusoidal signal are analytically investigated by using lira sup and lim inf in advanced calculus. We show that if the covariance matrix has a limit, then it must be a zero matrix.
