Clouds are critical to the global radiation budget and hydrological cycle, but knowledge is still poor concerning the observed climatology of cloud-base height （CBH） in China. Based on fine-resolution sounding obser...Clouds are critical to the global radiation budget and hydrological cycle, but knowledge is still poor concerning the observed climatology of cloud-base height （CBH） in China. Based on fine-resolution sounding observations from the China Radiosonde Network （CRN）, the method used to estimate CBH was modified, and uncertainty analyses indicated that the CBH is good enough. The accuracy of CBH estimation is verified by the comparison between the sounding-derived CBHs and those estimated from the micro-pulse lidar and millimeter-wave cloud radar. As such, the CBH climatology was compiled for the period 2006-16. Overall, the CBH exhibits large geographic variability across China, at both 0800 Local Standard Time （LST） and 2000 LST, irrespective of season. In addition, the summertime cloud base tends to be elevated to higher altitudes in dry regions [i.e., Inner Mongolia and the North China Plain （NCP）]. By comparison, the Tibetan Plateau （TP）, Pearl River Delta （PRD） and Sichuan Basin （SCB） have relatively low CBHs （〈 2.4 km above ground level）. In terms of seasonality, the CBH reaches its maximum in summer and minimum in winter. A low cloud base tends to occur frequently （〉 70%） over the TP, PRD and SCB. In contrast, at most sites over the Yangtze River Delta （YRD） and the NCP, about half the cloud belongs to the high-cloud category. The CBH does not exhibit marked diurnal variation in summer, throughout all CRN sites, probably due to the persistent cloud coverage caused by the East Asia Summer Monsson. To the best of our knowledge, this is the first CBH climatology produced from sounding measurements in China, and provides a useful reference for obtaining observational cloud base information.展开更多
The satellite-based quantification of cloud radiative forcing remains poorly understood,due largely to the limitation or uncertainties in characterizing cloud-base height(CBH).Here,we use the CBH data from radiosonde ...The satellite-based quantification of cloud radiative forcing remains poorly understood,due largely to the limitation or uncertainties in characterizing cloud-base height(CBH).Here,we use the CBH data from radiosonde measurements over China in combination with the collocated cloud-top height(CTH) and cloud properties from MODIS/Aqua to quantify the impact of CBH on shortwave cloud radiative forcing(SWCRF).The climatological mean SWCRF at the surface(SWCRFSUR),at the top of the atmosphere(SWCRFTOA),and in the atmosphere(SWCRFATM) are estimated to be-97.14,-84.35,and 12.79 W m^(-2),respectively for the summers spanning 2010 to 2018 over China.To illustrate the role of the cloud base,we assume four scenarios according to vertical profile patterns of cloud optical depth(COD).Using the CTH and cloud properties from MODIS alone results in large uncertainties for the estimation of SWCRFATM,compared with those under scenarios that consider the CBH.Furthermore,the biases of the CERES estimation of SWCRFATM tend to increase in the presence of thick clouds with low CBH.Additionally,the discrepancy of SWCRFATM relative to that calculated without consideration of CBH varies according to the vertical profile of COD.When a uniform COD vertical profile is assumed,the largest SWCRF discrepancies occur during the early morning or late afternoon.By comparison,the two-point COD vertical distribution assumption has the largest uncertainties occurring at noon when the solar irradiation peaks.These findings justify the urgent need to consider the cloud vertical structures when calculating the SWCRF which is otherwise neglected.展开更多
Cloud base height(CBH) is a crucial parameter for cloud radiative effect estimates, climate change simulations, and aviation guidance. However, due to the limited information on cloud vertical structures included in p...Cloud base height(CBH) is a crucial parameter for cloud radiative effect estimates, climate change simulations, and aviation guidance. However, due to the limited information on cloud vertical structures included in passive satellite radiometer observations, few operational satellite CBH products are currently available. This study presents a new method for retrieving CBH from satellite radiometers. The method first uses the combined measurements of satellite radiometers and ground-based cloud radars to develop a lookup table(LUT) of effective cloud water content(ECWC), representing the vertically varying cloud water content. This LUT allows for the conversion of cloud water path to cloud geometric thickness(CGT), enabling the estimation of CBH as the difference between cloud top height and CGT. Detailed comparative analysis of CBH estimates from the state-of-the-art ECWC LUT are conducted against four ground-based millimeter-wave cloud radar(MMCR) measurements, and results show that the mean bias(correlation coefficient) is0.18±1.79 km(0.73), which is lower(higher) than 0.23±2.11 km(0.67) as derived from the combined measurements of satellite radiometers and satellite radar-lidar(i.e., Cloud Sat and CALIPSO). Furthermore, the percentages of the CBH biases within 250 m increase by 5% to 10%, which varies by location. This indicates that the CBH estimates from our algorithm are more consistent with ground-based MMCR measurements. Therefore, this algorithm shows great potential for further improvement of the CBH retrievals as ground-based MMCR are being increasingly included in global surface meteorological observing networks, and the improved CBH retrievals will contribute to better cloud radiative effect estimates.展开更多
Based on ground-based Atmospheric Emitted Radiance Interferometer (AERI) observations in Shouxian, Anhui province, China, the authors retrieve the cloud base height (CBH) and effective cloud emissivity by using the mi...Based on ground-based Atmospheric Emitted Radiance Interferometer (AERI) observations in Shouxian, Anhui province, China, the authors retrieve the cloud base height (CBH) and effective cloud emissivity by using the minimum root-mean-square difference method. This method was originally developed for satellite remote sensing. The high-temporal-resolution retrieval results can depict the trivial variations of the zenith clouds continu-ously. The retrieval results are evaluated by comparing them with observations by the cloud radar. The comparison shows that the retrieval bias is smaller for the middle and low cloud, especially for the opaque cloud. When two layers of clouds exist, the retrieval results reflect the weighting radiative contribution of the multi-layer cloud. The retrieval accuracy is affected by uncertainties of the AERI radiances and sounding profiles, in which the role of uncertainty in the temperature profile is dominant.展开更多
In this study,cloud base height（CBH） and cloud top height（CTH） observed by the Ka-band（33.44 GHz） cloud radar at the Boseong National Center for Intensive Observation of Severe Weather during fall 2013（Septembe...In this study,cloud base height（CBH） and cloud top height（CTH） observed by the Ka-band（33.44 GHz） cloud radar at the Boseong National Center for Intensive Observation of Severe Weather during fall 2013（September-November） were verified and corrected.For comparative verification,CBH and CTH were obtained using a ceilometer（CL51） and the Communication,Ocean and Meteorological Satellite（COMS）.During rainfall,the CBH and CTH observed by the cloud radar were lower than observed by the ceilometer and COMS because of signal attenuation due to raindrops,and this difference increased with rainfall intensity.During dry periods,however,the CBH and CTH observed by the cloud radar,ceilometer,and COMS were similar.Thin and low-density clouds were observed more effectively by the cloud radar compared with the ceilometer and COMS.In cases of rainfall or missing cloud radar data,the ceilometer and COMS data were proven effective in correcting or compensating the cloud radar data.These corrected cloud data were used to classify cloud types,which revealed that low clouds occurred most frequently.展开更多
In the paper, we propose a new method of identifying the clear sky based on the Atmospheric Emitted Radiance Interferometer （AERI）. Using the Atmospheric Radiation Measurement （ARM） Mobile Facility （AFM） dataset...In the paper, we propose a new method of identifying the clear sky based on the Atmospheric Emitted Radiance Interferometer （AERI）. Using the Atmospheric Radiation Measurement （ARM） Mobile Facility （AFM） dataset in Shouxian in 2008, we sim- ulate the downwelling radiances on the surface in the 8-12 μm window region using Line-By-Line Radiative Transfer Model （LBLRTM）, and compare the results with the AERI radiances, The differences larger （smaller） than 3 mW （cm2 sr cm-1）-1 suggest a cloudy （clear） sky. Meanwhile, we develop the new algorithms for retrieving the zenith equivalent cloud base height （CBHe） and the equivalent emissivity （ee）, respectively. The retrieval methods are described as follows. （1） An infinitely thin and isothermal blackbody cloud is simulated by the LBLRTM. The cloud base height （H） is adjusted iteratively to satisfy the situation that the contribution of the blackbody to the downwelling radiance is equal to that of realistic cloud. The final H is considered as CBHe. The retrieval results indicate that the differences between the CBHe and observational cloud base height （CBH） are much smaller for thick low cloud, and increase with the increasing CBH. （2） An infinitely thin and isothermal gray body cloud is simulated by the LBLRTM, with the CBH specified as the observed value. The cloud base emissivity （co） is ad- justed iteratively until the contribution of the gray body to the downwelling radiance is the same as that of realistic cloud. The corresponding εc is εe. The average εe for the low, middle, and high cloud is 0.967, 0.781, and 0.616 for the 50 cases, respec- tively. It decreases with the increasing CBH. The retrieval results will be useful for studying the role of cloud in the radiation budget in the window region and cloud parameterizations in the climate model.展开更多
Building detection in very high resolution (VHR) images is crucial for mapping and analysing urban environments. Since buildings are elevated objects, elevation data need to be integrated with images for reliable dete...Building detection in very high resolution (VHR) images is crucial for mapping and analysing urban environments. Since buildings are elevated objects, elevation data need to be integrated with images for reliable detection. This process requires two critical steps: optical-elevation data co-registration and aboveground elevation calculation. These two steps are still challenging to some extent. Therefore, this paper introduces optical-elevation data co-registration and normalization techniques for generating a dataset that facilitates elevation-based building detection. For achieving accurate co-registration, a dense set of stereo-based elevations is generated and co-registered to their relevant image based on their corresponding image locations. To normalize these co-registered elevations, the bare-earth elevations are detected based on classification information of some terrain-level features after achieving the image co-registration. The developed method was executed and validated. After implementation, 80% overall-quality of detection result was achieved with 94% correct detection. Together, the developed techniques successfully facilitate the incorporation of stereo-based elevations for detecting buildings in VHR remote sensing images.展开更多
Korean larch(Larix olgensis)is one of the main tree species for aff orestation and timber production in northeast China.However,its timber quality and growth ability are largely infl uenced by crown size,structure and...Korean larch(Larix olgensis)is one of the main tree species for aff orestation and timber production in northeast China.However,its timber quality and growth ability are largely infl uenced by crown size,structure and shape.The majority of crown models are static models based on tree size and stand characteristics from temporary sample plots,but crown dynamic models has seldom been constructed.Therefore,this study aimed to develop height to crown base(HCB)and crown length(CL)dynamic models using the branch mortality technique for a Korean larch plantation.The nonlinear mixed-eff ects model with random eff ects,variance functions and correlation structures,was used to build HCB and CL dynamic models.The data were obtained from 95 sample trees of 19 plots in Meng JiaGang forest farm in Northeast China.The results showed that HCB progressively increases as tree age,tree height growth(HT growth)and diameter at breast height growth(DBH growth).The CL was increased with tree age in 20 years ago,and subsequently stabilized.HT growth,DBH growth stand basal area(BAS)and crown competition factor(CCF)signifi cantly infl uenced HCB and CL.The HCB was positively correlated with BAS,HT growth and DBH growth,but negatively correlated with CCF.The CL was positively correlated with BAS and CCF,but negatively correlated with DBH growth.Model fi tting and validation confi rmed that the mixed-eff ects model considering the stand and tree level random eff ects was accurate and reliable for predicting the HCB and CL dynamics.However,the models involving adding variance functions and time series correlation structure could not completely remove heterogeneity and autocorrelation,and the fi tting precision of the models was reduced.Therefore,from the point of view of application,we should take care to avoid setting up over-complex models.The HCB and CL dynamic models in our study may also be incorporated into stand growth and yield model systems in China.展开更多
Background： Tree species recognition is the main bottleneck in remote sensing based inventories aiming to produce an input for species-specific growth and yield models. We hypothesized that a stratification of the ta...Background： Tree species recognition is the main bottleneck in remote sensing based inventories aiming to produce an input for species-specific growth and yield models. We hypothesized that a stratification of the target data according to the dominant species could improve the subsequent predictions of species-specific attributes in particular in study areas strongly dominated by certain species. Methods： We tested this hypothesis and an operational potential to improve the predictions of timber volumes, stratified to Scots pine, Norway spruce and deciduous trees, in a conifer forest dominated by the pine species. We derived predictor features from airborne laser scanning （ALS） data and used Most Similar Neighbor （MSN） and Seemingly Unrelated Regression （SUR） as examples of non-parametric and parametric prediction methods, respectively Results： The relationships between the ALS features and the volumes of the aforementioned species were considerably different depending on the dominant species. Incorporating the observed dominant species inthe predictions improved the root mean squared errors by 13.3-16.4 % and 12.6-28.9 % based on MSN and SUR, respectively, depending on the species. Predicting the dominant species based on a linear discriminant analysis had an overall accuracy of only 76 % at best, which degraded the accuracies of the predicted volumes. Consequently, the predictions that did not consider the dominant species were more accurate than those refined with the predicted species. The MSN method gave slightly better results than models fitted with SUR. Conclusions： According to our results, incorporating information on the dominant species has a clear potential to improve the subsequent predictions of species-specific forest attributes. Determining the dominant species based solely on ALS data is deemed challenging, but important in particular in areas where the species composition is otherwise seemingly homogeneous except being dominated by certain species.展开更多
CuSn powders and Till2 powders were milled using high energy mechanical milling to prepare Cu-based alloy powders for brazing diamond. And Ce was added to the milled Cu-based alloy powders to improve the wettability. ...CuSn powders and Till2 powders were milled using high energy mechanical milling to prepare Cu-based alloy powders for brazing diamond. And Ce was added to the milled Cu-based alloy powders to improve the wettability. It is found that the wetting angle reaches the minimum value 13.2° and the maximum spreading area 178 mm2 is achieved when the amount of Ce is 0.75 wt%. And Ce remarkably reduces the surface tension of liquid alloy, which improves the climbing height along the diamond and forms a massive support profile. And the results show that Ce can effectively improve the transverse rupture strength （TRS） due to high wettability. The wear characteristics of the diamonds brazed with Cu-based alloy containing 0.75 wt% Ce mainly consist of integrity, micro-fracture, fracture and rubdown, diamonds pull-out can not easily happen.展开更多
The sounding data of a multi-channel parallel ground-based microwave radiometer （MWR） in Fuzhou station in July and August in 2016 were compared with the sounding data of a radiosonde in the same position in the sam...The sounding data of a multi-channel parallel ground-based microwave radiometer （MWR） in Fuzhou station in July and August in 2016 were compared with the sounding data of a radiosonde in the same position in the same period. The results showed that the correlations between the two types of temperature or humidity detected by the microwave radiometer and the radiosonde were significant at 0.05 level, indicating that the overall changing trends of temperature or humidity detected by the two devices were similar. The temperature detected by the microwave radiometer and the radiosonde decreased with the increase of height. The difference between the changes in the height of the zero layer detected by the micro- wave radiometer and the radiosonde was not significant, and their trends were basically the same.展开更多
基金the Ministry of Science and Technology of China (Grant Nos. 2017YFC1501701, 2017YFC1501401, 2017YFA0603501 and 2016YFA0600403)the National Natural Science Foundation of China (Grant Nos. 91544217, 41771399 and 41471301)+1 种基金the Chinese Academy of Meteorological Sciences (Grant Nos. 2017Z005 and 2017R001)the Fundamental Research Funds for the Central Universities (Grant No. 2017STUD17)
文摘Clouds are critical to the global radiation budget and hydrological cycle, but knowledge is still poor concerning the observed climatology of cloud-base height （CBH） in China. Based on fine-resolution sounding observations from the China Radiosonde Network （CRN）, the method used to estimate CBH was modified, and uncertainty analyses indicated that the CBH is good enough. The accuracy of CBH estimation is verified by the comparison between the sounding-derived CBHs and those estimated from the micro-pulse lidar and millimeter-wave cloud radar. As such, the CBH climatology was compiled for the period 2006-16. Overall, the CBH exhibits large geographic variability across China, at both 0800 Local Standard Time （LST） and 2000 LST, irrespective of season. In addition, the summertime cloud base tends to be elevated to higher altitudes in dry regions [i.e., Inner Mongolia and the North China Plain （NCP）]. By comparison, the Tibetan Plateau （TP）, Pearl River Delta （PRD） and Sichuan Basin （SCB） have relatively low CBHs （〈 2.4 km above ground level）. In terms of seasonality, the CBH reaches its maximum in summer and minimum in winter. A low cloud base tends to occur frequently （〉 70%） over the TP, PRD and SCB. In contrast, at most sites over the Yangtze River Delta （YRD） and the NCP, about half the cloud belongs to the high-cloud category. The CBH does not exhibit marked diurnal variation in summer, throughout all CRN sites, probably due to the persistent cloud coverage caused by the East Asia Summer Monsson. To the best of our knowledge, this is the first CBH climatology produced from sounding measurements in China, and provides a useful reference for obtaining observational cloud base information.
基金support from the National Key R&D Program of China under Grants Nos.2017YFC1501401 and 2017YFC0212803the National Natural Science Foundation under Grant No.41771399the Chinese Academy of Meteorological Sciences under Grant No.2018Y014。
文摘The satellite-based quantification of cloud radiative forcing remains poorly understood,due largely to the limitation or uncertainties in characterizing cloud-base height(CBH).Here,we use the CBH data from radiosonde measurements over China in combination with the collocated cloud-top height(CTH) and cloud properties from MODIS/Aqua to quantify the impact of CBH on shortwave cloud radiative forcing(SWCRF).The climatological mean SWCRF at the surface(SWCRFSUR),at the top of the atmosphere(SWCRFTOA),and in the atmosphere(SWCRFATM) are estimated to be-97.14,-84.35,and 12.79 W m^(-2),respectively for the summers spanning 2010 to 2018 over China.To illustrate the role of the cloud base,we assume four scenarios according to vertical profile patterns of cloud optical depth(COD).Using the CTH and cloud properties from MODIS alone results in large uncertainties for the estimation of SWCRFATM,compared with those under scenarios that consider the CBH.Furthermore,the biases of the CERES estimation of SWCRFATM tend to increase in the presence of thick clouds with low CBH.Additionally,the discrepancy of SWCRFATM relative to that calculated without consideration of CBH varies according to the vertical profile of COD.When a uniform COD vertical profile is assumed,the largest SWCRF discrepancies occur during the early morning or late afternoon.By comparison,the two-point COD vertical distribution assumption has the largest uncertainties occurring at noon when the solar irradiation peaks.These findings justify the urgent need to consider the cloud vertical structures when calculating the SWCRF which is otherwise neglected.
基金funded by the National Natural Science Foundation of China (Grant Nos. 42305150 and 42325501)the China Postdoctoral Science Foundation (Grant No. 2023M741774)。
文摘Cloud base height(CBH) is a crucial parameter for cloud radiative effect estimates, climate change simulations, and aviation guidance. However, due to the limited information on cloud vertical structures included in passive satellite radiometer observations, few operational satellite CBH products are currently available. This study presents a new method for retrieving CBH from satellite radiometers. The method first uses the combined measurements of satellite radiometers and ground-based cloud radars to develop a lookup table(LUT) of effective cloud water content(ECWC), representing the vertically varying cloud water content. This LUT allows for the conversion of cloud water path to cloud geometric thickness(CGT), enabling the estimation of CBH as the difference between cloud top height and CGT. Detailed comparative analysis of CBH estimates from the state-of-the-art ECWC LUT are conducted against four ground-based millimeter-wave cloud radar(MMCR) measurements, and results show that the mean bias(correlation coefficient) is0.18±1.79 km(0.73), which is lower(higher) than 0.23±2.11 km(0.67) as derived from the combined measurements of satellite radiometers and satellite radar-lidar(i.e., Cloud Sat and CALIPSO). Furthermore, the percentages of the CBH biases within 250 m increase by 5% to 10%, which varies by location. This indicates that the CBH estimates from our algorithm are more consistent with ground-based MMCR measurements. Therefore, this algorithm shows great potential for further improvement of the CBH retrievals as ground-based MMCR are being increasingly included in global surface meteorological observing networks, and the improved CBH retrievals will contribute to better cloud radiative effect estimates.
基金supported by the National Natural Science Foundation of China (Grant No. 40710059003)
文摘Based on ground-based Atmospheric Emitted Radiance Interferometer (AERI) observations in Shouxian, Anhui province, China, the authors retrieve the cloud base height (CBH) and effective cloud emissivity by using the minimum root-mean-square difference method. This method was originally developed for satellite remote sensing. The high-temporal-resolution retrieval results can depict the trivial variations of the zenith clouds continu-ously. The retrieval results are evaluated by comparing them with observations by the cloud radar. The comparison shows that the retrieval bias is smaller for the middle and low cloud, especially for the opaque cloud. When two layers of clouds exist, the retrieval results reflect the weighting radiative contribution of the multi-layer cloud. The retrieval accuracy is affected by uncertainties of the AERI radiances and sounding profiles, in which the role of uncertainty in the temperature profile is dominant.
基金supported by the principal project, “Development and application of technology for weather forecasting (NIMR-2012-B-1)” of the National Institute of Meteorological Sciences of the Korea Meteorological Administration
文摘In this study,cloud base height（CBH） and cloud top height（CTH） observed by the Ka-band（33.44 GHz） cloud radar at the Boseong National Center for Intensive Observation of Severe Weather during fall 2013（September-November） were verified and corrected.For comparative verification,CBH and CTH were obtained using a ceilometer（CL51） and the Communication,Ocean and Meteorological Satellite（COMS）.During rainfall,the CBH and CTH observed by the cloud radar were lower than observed by the ceilometer and COMS because of signal attenuation due to raindrops,and this difference increased with rainfall intensity.During dry periods,however,the CBH and CTH observed by the cloud radar,ceilometer,and COMS were similar.Thin and low-density clouds were observed more effectively by the cloud radar compared with the ceilometer and COMS.In cases of rainfall or missing cloud radar data,the ceilometer and COMS data were proven effective in correcting or compensating the cloud radar data.These corrected cloud data were used to classify cloud types,which revealed that low clouds occurred most frequently.
基金supported by the Chinese Academy of Sciences (Grant No. XDA05040300)National Natural Science Foundation of China (Grant No. 40710059003)
文摘In the paper, we propose a new method of identifying the clear sky based on the Atmospheric Emitted Radiance Interferometer （AERI）. Using the Atmospheric Radiation Measurement （ARM） Mobile Facility （AFM） dataset in Shouxian in 2008, we sim- ulate the downwelling radiances on the surface in the 8-12 μm window region using Line-By-Line Radiative Transfer Model （LBLRTM）, and compare the results with the AERI radiances, The differences larger （smaller） than 3 mW （cm2 sr cm-1）-1 suggest a cloudy （clear） sky. Meanwhile, we develop the new algorithms for retrieving the zenith equivalent cloud base height （CBHe） and the equivalent emissivity （ee）, respectively. The retrieval methods are described as follows. （1） An infinitely thin and isothermal blackbody cloud is simulated by the LBLRTM. The cloud base height （H） is adjusted iteratively to satisfy the situation that the contribution of the blackbody to the downwelling radiance is equal to that of realistic cloud. The final H is considered as CBHe. The retrieval results indicate that the differences between the CBHe and observational cloud base height （CBH） are much smaller for thick low cloud, and increase with the increasing CBH. （2） An infinitely thin and isothermal gray body cloud is simulated by the LBLRTM, with the CBH specified as the observed value. The cloud base emissivity （co） is ad- justed iteratively until the contribution of the gray body to the downwelling radiance is the same as that of realistic cloud. The corresponding εc is εe. The average εe for the low, middle, and high cloud is 0.967, 0.781, and 0.616 for the 50 cases, respec- tively. It decreases with the increasing CBH. The retrieval results will be useful for studying the role of cloud in the radiation budget in the window region and cloud parameterizations in the climate model.
文摘Building detection in very high resolution (VHR) images is crucial for mapping and analysing urban environments. Since buildings are elevated objects, elevation data need to be integrated with images for reliable detection. This process requires two critical steps: optical-elevation data co-registration and aboveground elevation calculation. These two steps are still challenging to some extent. Therefore, this paper introduces optical-elevation data co-registration and normalization techniques for generating a dataset that facilitates elevation-based building detection. For achieving accurate co-registration, a dense set of stereo-based elevations is generated and co-registered to their relevant image based on their corresponding image locations. To normalize these co-registered elevations, the bare-earth elevations are detected based on classification information of some terrain-level features after achieving the image co-registration. The developed method was executed and validated. After implementation, 80% overall-quality of detection result was achieved with 94% correct detection. Together, the developed techniques successfully facilitate the incorporation of stereo-based elevations for detecting buildings in VHR remote sensing images.
基金supported by the National Key Research and Development Program of China(2017YFD0600401)the Fundamental Research Funds for the Central Universities(2572019CP08)
文摘Korean larch(Larix olgensis)is one of the main tree species for aff orestation and timber production in northeast China.However,its timber quality and growth ability are largely infl uenced by crown size,structure and shape.The majority of crown models are static models based on tree size and stand characteristics from temporary sample plots,but crown dynamic models has seldom been constructed.Therefore,this study aimed to develop height to crown base(HCB)and crown length(CL)dynamic models using the branch mortality technique for a Korean larch plantation.The nonlinear mixed-eff ects model with random eff ects,variance functions and correlation structures,was used to build HCB and CL dynamic models.The data were obtained from 95 sample trees of 19 plots in Meng JiaGang forest farm in Northeast China.The results showed that HCB progressively increases as tree age,tree height growth(HT growth)and diameter at breast height growth(DBH growth).The CL was increased with tree age in 20 years ago,and subsequently stabilized.HT growth,DBH growth stand basal area(BAS)and crown competition factor(CCF)signifi cantly infl uenced HCB and CL.The HCB was positively correlated with BAS,HT growth and DBH growth,but negatively correlated with CCF.The CL was positively correlated with BAS and CCF,but negatively correlated with DBH growth.Model fi tting and validation confi rmed that the mixed-eff ects model considering the stand and tree level random eff ects was accurate and reliable for predicting the HCB and CL dynamics.However,the models involving adding variance functions and time series correlation structure could not completely remove heterogeneity and autocorrelation,and the fi tting precision of the models was reduced.Therefore,from the point of view of application,we should take care to avoid setting up over-complex models.The HCB and CL dynamic models in our study may also be incorporated into stand growth and yield model systems in China.
基金financed by the Finnish Funding Agency for Innovation(Tekes) and its business and research partners
文摘Background： Tree species recognition is the main bottleneck in remote sensing based inventories aiming to produce an input for species-specific growth and yield models. We hypothesized that a stratification of the target data according to the dominant species could improve the subsequent predictions of species-specific attributes in particular in study areas strongly dominated by certain species. Methods： We tested this hypothesis and an operational potential to improve the predictions of timber volumes, stratified to Scots pine, Norway spruce and deciduous trees, in a conifer forest dominated by the pine species. We derived predictor features from airborne laser scanning （ALS） data and used Most Similar Neighbor （MSN） and Seemingly Unrelated Regression （SUR） as examples of non-parametric and parametric prediction methods, respectively Results： The relationships between the ALS features and the volumes of the aforementioned species were considerably different depending on the dominant species. Incorporating the observed dominant species inthe predictions improved the root mean squared errors by 13.3-16.4 % and 12.6-28.9 % based on MSN and SUR, respectively, depending on the species. Predicting the dominant species based on a linear discriminant analysis had an overall accuracy of only 76 % at best, which degraded the accuracies of the predicted volumes. Consequently, the predictions that did not consider the dominant species were more accurate than those refined with the predicted species. The MSN method gave slightly better results than models fitted with SUR. Conclusions： According to our results, incorporating information on the dominant species has a clear potential to improve the subsequent predictions of species-specific forest attributes. Determining the dominant species based solely on ALS data is deemed challenging, but important in particular in areas where the species composition is otherwise seemingly homogeneous except being dominated by certain species.
基金Project supported by National Natural Science Foundation of China(51575179,51205126)Natural Science Foundation of Hunan Province(2017JJ3073,12JJB006)
文摘CuSn powders and Till2 powders were milled using high energy mechanical milling to prepare Cu-based alloy powders for brazing diamond. And Ce was added to the milled Cu-based alloy powders to improve the wettability. It is found that the wetting angle reaches the minimum value 13.2° and the maximum spreading area 178 mm2 is achieved when the amount of Ce is 0.75 wt%. And Ce remarkably reduces the surface tension of liquid alloy, which improves the climbing height along the diamond and forms a massive support profile. And the results show that Ce can effectively improve the transverse rupture strength （TRS） due to high wettability. The wear characteristics of the diamonds brazed with Cu-based alloy containing 0.75 wt% Ce mainly consist of integrity, micro-fracture, fracture and rubdown, diamonds pull-out can not easily happen.
文摘The sounding data of a multi-channel parallel ground-based microwave radiometer （MWR） in Fuzhou station in July and August in 2016 were compared with the sounding data of a radiosonde in the same position in the same period. The results showed that the correlations between the two types of temperature or humidity detected by the microwave radiometer and the radiosonde were significant at 0.05 level, indicating that the overall changing trends of temperature or humidity detected by the two devices were similar. The temperature detected by the microwave radiometer and the radiosonde decreased with the increase of height. The difference between the changes in the height of the zero layer detected by the micro- wave radiometer and the radiosonde was not significant, and their trends were basically the same.
