Affected by external environmental factors and evolution of dam performance, dam seepage behavior shows nonlinear time-varying characteristics. In this study, to predict and evaluate the long-term development trend an...Affected by external environmental factors and evolution of dam performance, dam seepage behavior shows nonlinear time-varying characteristics. In this study, to predict and evaluate the long-term development trend and short-term fluctuation of the dam seepage behavior, two monitoring models were developed, one for the base flow effect and one for daily variation of dam seepage elements. In the first model, to avoid the influence of the time lag effect on the evaluation of seepage variation with the time effect component of seepage elements, the base values of the seepage element and the reservoir water level were extracted using the wavelet multi-resolution analysis method, and the time effect component was separated by the established base flow effect monitoring model. For the development of the daily variation monitoring model for dam seepage elements, all the previous factors, of which the measured time series prior to the dam seepage element monitoring time may have certain influence on the monitored results, were considered. Those factors that were positively correlated with the analyzed seepage element were initially considered to be the support vector machine(SVM) model input factors, and then the SVM kernel function-based sensitivity analysis was performed to optimize the input factor set and establish the optimized daily variation SVM model. The efficiency and rationality of the two models were verified by case studies of the water level of two piezometric tubes buried under the slope of a concrete gravity dam.Sensitivity analysis of the optimized SVM model shows that the influences of the daily variation of the upstream reservoir water level and rainfall on the daily variation of piezometric tube water level are processes subject to normal distribution.展开更多
The flows behind the base of a generic rocket, at both hypersonic and subsonic flow conditions, are numerically studied. The main concerns are addressed to the evaluation of turbulence models and the using of grid ada...The flows behind the base of a generic rocket, at both hypersonic and subsonic flow conditions, are numerically studied. The main concerns are addressed to the evaluation of turbulence models and the using of grid adaptation techniques. The investigation focuses on two configurations, related to hypersonic and subsonic experiments. The applicability tests of different turbu- lence models are conducted on the level of two-equation models calculating the steady state solution of the Reynolds-averaged Navier-Stokes（RANS） equations. All used models, the original Wilcox k-co, the Menter shear-stress transport （SST） and the ex- plicit algebraic Reynolds stress model（EARSM） formulation, predict an asymmetric base flow in both cases caused by the support of the models. A comparison with preliminary experimental results indicates a preference for the SST and EARSM results over the results from the older k-co model. Sensitivity studies show no significant influence of the grid topology or the location of the laminar to turbulent transition on the base flow field, but a strong influence of even small angles of attack is reported from the related experiments.展开更多
The most controversial river in Thailand is the Yom River.It has not been modified by large dam because of several valuable natural resources.Therefore,the river is flooded in rainy season and very low flow in dry sea...The most controversial river in Thailand is the Yom River.It has not been modified by large dam because of several valuable natural resources.Therefore,the river is flooded in rainy season and very low flow in dry season.The low flow causes drought which is much more serious than flooding.The Yom River Basin management is only way to circumvent the low flow problem by studying base flow index(BFI).Base flow analyses for 8 gauging stations along the river were performed by 2 techniques i.e.graphical and modified U.K.Institute of Hydrology(MIH).The mean BFI results from graphical and MIH are 0.37(0.05)and 0.45(0.12).The result from graphical is more reasonable due to its lower standard deviation.BFI values from MIH vary with watershed area which may result from the using of fixing value of N-day at 10.Solution for this problem is ongoing in this study.展开更多
In order to improve the benefits of base bleed in base flow field,the base flow with hot base bleed for two jet models is studied.Twodimensional axisymmetric Navier-Stokes equations are computed by using a finite volu...In order to improve the benefits of base bleed in base flow field,the base flow with hot base bleed for two jet models is studied.Twodimensional axisymmetric Navier-Stokes equations are computed by using a finite volume scheme.The base flow of a cylinder afterbody with base bleed is simulated.The simulation results are validated with the experimental data,and the experimental results are well reproduced.On this basis,the base flow fields with base bleed for a circular jet model and an annulus jet model are investigated by selecting the injection temperature from 830 K to 2200 K.The results show that the base pressure of the annular jet model is higher than that of the circular jet model with the changes of the injection parameter and the injection temperature.For the circular jet model,the hot gases are concentrated in the vicinity of the base.For the annular jet model,the bleed gases flow into the shear layer directly so that the hot gases are concentrated in the shear layer.The latter temperature distribution is better for the increase of base pressure.展开更多
This paper presents a sensitivity analysis method for analyzing the key factors affecting the stability problem of the transonic compressors.The adjoint method is integrated into the meridional stability model,a linea...This paper presents a sensitivity analysis method for analyzing the key factors affecting the stability problem of the transonic compressors.The adjoint method is integrated into the meridional stability model,a linear stability prediction model utilized to analyze the flow stability problem of the compressor,and the sensitivity analysis method is further developed for the flow stability problem of the compressor.The study selects the NASA Rot or 37,a transonic compressor,as the research object to verify the proposed method and explore the sensitive factors leading to the stall inception.The results of sensitivity analysis to both the flow parameters and the external source terms reveal that the stall inception is sensitive to the base flow field at the rotor tip and the stability margin of the compressor can be enhanced by improving the flow field at this region.Physical explanations are presented and discussed to correlate the three-dimensional flow field to the results obtained via the employed analysis method,which shows that flow structures and characteristics near the end-wall region,especially the tip leakage flow or the tip leakage vortex and its interaction with the shock wave,contribute to the stall inception.展开更多
Automatic Digital Orthophoto Map(DOM)generation plays an important role in many downstream works such as land use and cover detection,urban planning,and disaster assessment.Existing DOM generation methods can generate...Automatic Digital Orthophoto Map(DOM)generation plays an important role in many downstream works such as land use and cover detection,urban planning,and disaster assessment.Existing DOM generation methods can generate promising results but always need ground object filtered DEM generation before otho-rectification;this can consume much time and produce building facade contained results.To address this problem,a pixel-by-pixel digital differential rectification-based automatic DOM generation method is proposed in this paper.Firstly,3D point clouds with texture are generated by dense image matching based on an optical flow field for a stereo pair of images,respectively.Then,the grayscale of the digital differential rectification image is extracted directly from the point clouds element by element according to the nearest neighbor method for matched points.Subsequently,the elevation is repaired grid-by-grid using the multi-layer Locally Refined B-spline(LR-B)interpolation method with triangular mesh constraint for the point clouds void area,and the grayscale is obtained by the indirect scheme of digital differential rectification to generate the pixel-by-pixel digital differentially rectified image of a single image slice.Finally,a seamline network is automatically searched using a disparity map optimization algorithm,and DOM is smartly mosaicked.The qualitative and quantitative experimental results on three datasets were produced and evaluated,which confirmed the feasibility of the proposed method,and the DOM accuracy can reach 1 Ground Sample Distance(GSD)level.The comparison experiment with the state-of-the-art commercial softwares showed that the proposed method generated DOM has a better visual effect on building boundaries and roof completeness with comparable accuracy and computational efficiency.展开更多
An analytical simulation based on a new model incorporating surface interaction is conducted to study the slip phenomenon in the Couette flow at different scales. The velocity profile is calculated by taking account o...An analytical simulation based on a new model incorporating surface interaction is conducted to study the slip phenomenon in the Couette flow at different scales. The velocity profile is calculated by taking account of the micro-force between molecules and macro-force from the viscous shearing effect, as they contribute to the achieve- ment of the slip length. The calculated results are compared with those obtained from the molecular dynamics simulation, showing an excellent agreement. Further, the effect of the shear rate on the slip is investigated. The results can well predict the fluid flow behaviors on a solid substrate, but has to be proved by experiment.展开更多
The drift-flux model has a practical importance in two-phase flow analysis.In this study,a finite volume solution is developed for a transient four-equation drift-flux model through the staggered mesh,leading to the d...The drift-flux model has a practical importance in two-phase flow analysis.In this study,a finite volume solution is developed for a transient four-equation drift-flux model through the staggered mesh,leading to the development of a fully implicit discretization method.The main advantage of the fully implicit method is its unconditional stability.Newton's scheme is a popular method of choice for the solution of a nonlinear system of equations arising from fully implicit discretization of field equations.However,the lack of convergence robustness and the construction of Jacobian matrix have created several difficulties for the researchers.In this paper,a fully implicit model is developed based on the SIMPLE algorithm for two-phase flow simulations.The drawbacks of Newton's method are avoided in the developed model.Different limiter functions are considered,and the stabilized method is developed under steady and transient conditions.The results obtained by the numerical modeling are in good agreement with the experimental data.As expected,the results prove that the developed model is not restricted by any stability limit.展开更多
Metal organic chenlical vapor deposition （AIOCVD） growth systems arc one of the. main types of equipment used for growing single crystal materials, such as GaN. To obtain fihn epitaxial materials with uniform perfor...Metal organic chenlical vapor deposition （AIOCVD） growth systems arc one of the. main types of equipment used for growing single crystal materials, such as GaN. To obtain fihn epitaxial materials with uniform performanee, the flow field and ternperature field in a GaN-MOCVD reactor are investigated by modeling and simulating. To make the simulation results more consistent with the actual situation, the gases in the reactor are considered to be compressible, making it possible to investigate the distributions of gas density and pressure in the reactor. The computational fluid dynamics method is used to stud,v the effects of inlet gas flow velocity, pressure in the reactor, rotational speed of graphite susceptor, and gases used in the growth, which has great guiding~ significance for the growth of GaN fihn materials.展开更多
A combined characteristic-based split algorithm and all adaptive meshing technique for analyzing two-dimensional viscous incompressible flow are presented. Tile method uses the three-node triangular element with equal...A combined characteristic-based split algorithm and all adaptive meshing technique for analyzing two-dimensional viscous incompressible flow are presented. Tile method uses the three-node triangular element with equal-order interpolation functions for all variables of tile velocity components and pressure. The main advantage of the combined nlethod is that it inlproves the sohltion accuracy by coupling an error estinla- tion procedure to an adaptive meshing technique that generates small elements in regions with a large change ill sohmtion gradients, mid at the same time, larger elements in the other regions. The performance of the combined procedure is evaluated by analyzing one test case of the flow past a cylinder, for their transient and steady-state flow behaviors.展开更多
The isolation and culture of conventional detection method of salmonella can not meet the testing requirements of quick and easy detection at the grassroots level. In this study, we prepare the fluorescent nanoparticl...The isolation and culture of conventional detection method of salmonella can not meet the testing requirements of quick and easy detection at the grassroots level. In this study, we prepare the fluorescent nanoparticles as a marker, covalently conjugate with monoclonal antibodies of Salmonella pullorum. The whole Salmonella pullorum antigen and goat anti-mouse antibody sprayed on the nitrocellulose membranes are used as test line and control line. The fluorescence nanoparticles immune based lateral flow strips are made according to the principle of antigen-antibody immune response. The test strips may interpret results within 30 min. The results of the salmonella A, S. agona, S. chester and S. arechavaleta are positive, including, S. agona for weakly positive. After analysis, it is found that in addition to the salmonella of group A, the other positive salmonella are in group B. But it is negative of S. derby, S. rissen, and other 6 kinds of salmonella, with good specificity. The fluorescence nanoparticles immune based lateral flow strips are a little of sample can be detected fast, easily, inexpensive, easy to universal without professional technical personnel detection method. It provides a new detection method for the detections of Salmonella pullorum.展开更多
A new video-based measurement is proposed to collect and investigate traffic flow parameters. The output of the measurement is velocity-headway distance data pairs. Because density can be directly acquired by the reci...A new video-based measurement is proposed to collect and investigate traffic flow parameters. The output of the measurement is velocity-headway distance data pairs. Because density can be directly acquired by the reciprocal of headway distance, the data pairs have the advantage of better simultaneity than those from common detectors. By now, over 33 000 pairs of data have been collected from two road sections in the cities of Shanghai and Zhengzhou. Through analyzing the video files recording traffic movements on urban expressways, the following issues are studied：laws of vehicle velocity changing with headway distance, proportions of di0erent driving behaviors in the traffic system, and characteristics of traffic flow in snowy days. The results show that the real road traffic is very complex, and factors such as location and climate need to be taken into consideration in the formation of traffic flow models.展开更多
When characterizing flows in miniaturized channels, the determination of the dynamic contact angle is important. By measuring the dynamic contact angle, the flow properties of the flowing liquid and the effect of mate...When characterizing flows in miniaturized channels, the determination of the dynamic contact angle is important. By measuring the dynamic contact angle, the flow properties of the flowing liquid and the effect of material properties on the flow can be characterized. A machine vision based system to measure the contact angle of front or rear menisci of a moving liquid plug is described in this article. In this research, transparent flow channels fabricated on thermoplastic polymer and sealed with an adhesive tape are used. The transparency of the channels enables image based monitoring and measurement of flow variables, including the dynamic contact angle. It is shown that the dynamic angle can be measured from a liquid flow in a channel using the image based measurement system. An image processing algorithm has been developed in a MATLAB environment. Images are taken using a CCD camera and the channels are illuminated using a custom made ring light. Two fitting methods, a circle and two parabolas, are experimented and the results are compared in the measurement of the dynamic contact angles.展开更多
Using the collected 433 heat flow values, we estimated the bases of methane hydrate stability zone （BHSZ）, in northern South China Sea （NSCS）. Through comparing BHSZs with the depths of bottom simulating reflecto...Using the collected 433 heat flow values, we estimated the bases of methane hydrate stability zone （BHSZ）, in northern South China Sea （NSCS）. Through comparing BHSZs with the depths of bottom simulating reflectors （BSRs）, in Shenhu Area （SA）, we found that there are big differences between them. In the north of SA, where the water depth is shallow, many slumps developed and the sedimentation rate is high, it appears great negative difference （as large as -192%）. However, to the southeast of SA, where the water depth is deeper, sedimentation rate is relatively low and uplift basement topography exists, it changes to positive difference （as large as ＋45%）. The differences change so great, which haven＇t been observed in other places of the world. After considering the errors from the process of heat flow measurement, the BSR depth, the relationship of thermal conductivity with the sediments depth, and the fluid flow activities, we conclude that the difference should be not caused by these errors. Such big disagreement may be due to the misunderstanding of BSR. The deviant ＂BSRs＂ could represent the paleo-BSRs or just gas-bearing sediment layers, such as unconformities or the specific strata where have different permeability, which are not hydraterelated BSRs.展开更多
To enhance the applicability and measurement accuracy of phase-based optical flow method using complex steerable pyramids in structural displacement measurement engineering applications, an improved method of optimizi...To enhance the applicability and measurement accuracy of phase-based optical flow method using complex steerable pyramids in structural displacement measurement engineering applications, an improved method of optimizing parameter settings is proposed. The optimized parameters include the best measurement points of the Region of Interest (ROI) and the levels of pyramid filters. Additionally, to address the issue of updating reference frames in practical applications due to the difficulty in estimating the maximum effective measurement value, a mechanism for dynamically updating reference frames is introduced. Experimental results demonstrate that compared to representative image gradient-based displacement measurement methods, the proposed method exhibits higher measurement accuracy in engineering applications. This provides reliable data support for structural damage identification research based on vibration signals and is expected to broaden the engineering application prospects for structural health monitoring.展开更多
In this work, we study the characteristics I-V and P-V of a silicon solar cell as well as its fill factor, its electrical power from the optimum thickness obtained in the base under variation of the irradiation energy...In this work, we study the characteristics I-V and P-V of a silicon solar cell as well as its fill factor, its electrical power from the optimum thickness obtained in the base under variation of the irradiation energy flow of charged particles. The recombination velocity at the junction corresponding to the maximum power point was also deduced.展开更多
The experimental investigation of unsteady complex flow fields in wind tunnels requires advanced measurement techniques. The most important of such image based measurement techniques are those for the measurement of p...The experimental investigation of unsteady complex flow fields in wind tunnels requires advanced measurement techniques. The most important of such image based measurement techniques are those for the measurement of planar flow velocity fields, planar pressure distribution, model location and deformation, model temperature and quantitative high speed flow visualization. The applications as carried out by DLR range from low speed flows to transonic flows, from high lift configurations to propellers and rotors, from wake vortex investigations in catapult facilities and water towing tanks to investigations of vortex break down phenomena on delta wings. The capability to use image based measurement techniques in transonic flows requires dedicated technical developments and experienced scientists due to the special environment of a transonic wind tunnel. In this paper an overview of the state-of-the art of the application of image based measurement techniques in transonic flows as performed by DLR＇s Institute of Aerodynamics and Flow Technology will be given.展开更多
In the present study,the base pressure variations induced by the presence of a cavity,known to have a strong influence of the behaviour of supersonic projectiles,are investigated through numerical solution of the bala...In the present study,the base pressure variations induced by the presence of a cavity,known to have a strong influence of the behaviour of supersonic projectiles,are investigated through numerical solution of the balance equations for mass,momentum,and energy.An area ratio of four is considered and numerical simulations are carried out at Mach M=1.2,1.4,1.6,and 1.8 assuming no cavity or cavity locations 0.5D,1D,1.5D,and 2D.The inlet pressure of the nozzle is considered as a flow variable.The Taguchi method is also used,and the considered cases are then analyzed using a full factorial experimental design.The results show that the cavity is effective in increasing the base pressure for the conditions examined.For other nozzle pressure ratios,cavities do not lead to passive control due the change in the reattachment length.The distribution of wall pressure reveals that,in general,a cavity used to implement passive control of the base pressure does not adversely influence the flow pattern in the domain.展开更多
基金supported by the National Natural Science Foundation of China(Grant No.51709021)the Open Foundation of the State Key Laboratory of Hydrology-Water Resources and Hydraulic Engineering(Grant No.2016491111)
文摘Affected by external environmental factors and evolution of dam performance, dam seepage behavior shows nonlinear time-varying characteristics. In this study, to predict and evaluate the long-term development trend and short-term fluctuation of the dam seepage behavior, two monitoring models were developed, one for the base flow effect and one for daily variation of dam seepage elements. In the first model, to avoid the influence of the time lag effect on the evaluation of seepage variation with the time effect component of seepage elements, the base values of the seepage element and the reservoir water level were extracted using the wavelet multi-resolution analysis method, and the time effect component was separated by the established base flow effect monitoring model. For the development of the daily variation monitoring model for dam seepage elements, all the previous factors, of which the measured time series prior to the dam seepage element monitoring time may have certain influence on the monitored results, were considered. Those factors that were positively correlated with the analyzed seepage element were initially considered to be the support vector machine(SVM) model input factors, and then the SVM kernel function-based sensitivity analysis was performed to optimize the input factor set and establish the optimized daily variation SVM model. The efficiency and rationality of the two models were verified by case studies of the water level of two piezometric tubes buried under the slope of a concrete gravity dam.Sensitivity analysis of the optimized SVM model shows that the influences of the daily variation of the upstream reservoir water level and rainfall on the daily variation of piezometric tube water level are processes subject to normal distribution.
基金German Research Foundation (Deutsche Forschungs-gemeinschaft-DFG) Sonderforschungsbereich Transregio 40
文摘The flows behind the base of a generic rocket, at both hypersonic and subsonic flow conditions, are numerically studied. The main concerns are addressed to the evaluation of turbulence models and the using of grid adaptation techniques. The investigation focuses on two configurations, related to hypersonic and subsonic experiments. The applicability tests of different turbu- lence models are conducted on the level of two-equation models calculating the steady state solution of the Reynolds-averaged Navier-Stokes（RANS） equations. All used models, the original Wilcox k-co, the Menter shear-stress transport （SST） and the ex- plicit algebraic Reynolds stress model（EARSM） formulation, predict an asymmetric base flow in both cases caused by the support of the models. A comparison with preliminary experimental results indicates a preference for the SST and EARSM results over the results from the older k-co model. Sensitivity studies show no significant influence of the grid topology or the location of the laminar to turbulent transition on the base flow field, but a strong influence of even small angles of attack is reported from the related experiments.
文摘The most controversial river in Thailand is the Yom River.It has not been modified by large dam because of several valuable natural resources.Therefore,the river is flooded in rainy season and very low flow in dry season.The low flow causes drought which is much more serious than flooding.The Yom River Basin management is only way to circumvent the low flow problem by studying base flow index(BFI).Base flow analyses for 8 gauging stations along the river were performed by 2 techniques i.e.graphical and modified U.K.Institute of Hydrology(MIH).The mean BFI results from graphical and MIH are 0.37(0.05)and 0.45(0.12).The result from graphical is more reasonable due to its lower standard deviation.BFI values from MIH vary with watershed area which may result from the using of fixing value of N-day at 10.Solution for this problem is ongoing in this study.
基金supported by National Nature Science Foundation of China(Grant No.51176076)
文摘In order to improve the benefits of base bleed in base flow field,the base flow with hot base bleed for two jet models is studied.Twodimensional axisymmetric Navier-Stokes equations are computed by using a finite volume scheme.The base flow of a cylinder afterbody with base bleed is simulated.The simulation results are validated with the experimental data,and the experimental results are well reproduced.On this basis,the base flow fields with base bleed for a circular jet model and an annulus jet model are investigated by selecting the injection temperature from 830 K to 2200 K.The results show that the base pressure of the annular jet model is higher than that of the circular jet model with the changes of the injection parameter and the injection temperature.For the circular jet model,the hot gases are concentrated in the vicinity of the base.For the annular jet model,the bleed gases flow into the shear layer directly so that the hot gases are concentrated in the shear layer.The latter temperature distribution is better for the increase of base pressure.
基金supported by the National Natural Science Foundation of China(Nos.52306036,52325602 and U2441279)the National Science and Technology Major Project,China(Nos.Y2022-Ⅱ-0003-0006 and Y2022-Ⅱ-0002-0005)supported by the Project of National Key Laboratory of Science and Technology on Aero-Engine Aero-thermodynamics,China(Nos.6142702200101 and 2024-CXPT-GF-JJ-88-0103)。
文摘This paper presents a sensitivity analysis method for analyzing the key factors affecting the stability problem of the transonic compressors.The adjoint method is integrated into the meridional stability model,a linear stability prediction model utilized to analyze the flow stability problem of the compressor,and the sensitivity analysis method is further developed for the flow stability problem of the compressor.The study selects the NASA Rot or 37,a transonic compressor,as the research object to verify the proposed method and explore the sensitive factors leading to the stall inception.The results of sensitivity analysis to both the flow parameters and the external source terms reveal that the stall inception is sensitive to the base flow field at the rotor tip and the stability margin of the compressor can be enhanced by improving the flow field at this region.Physical explanations are presented and discussed to correlate the three-dimensional flow field to the results obtained via the employed analysis method,which shows that flow structures and characteristics near the end-wall region,especially the tip leakage flow or the tip leakage vortex and its interaction with the shock wave,contribute to the stall inception.
基金supported by the National Natural Science Foundation of China[Grant No.41771479]the National High-Resolution Earth Observation System(the Civil Part)[Grant No.50-H31D01-0508-13/15]the Japan Society for the Promotion of Science[Grant No.22H03573].
文摘Automatic Digital Orthophoto Map(DOM)generation plays an important role in many downstream works such as land use and cover detection,urban planning,and disaster assessment.Existing DOM generation methods can generate promising results but always need ground object filtered DEM generation before otho-rectification;this can consume much time and produce building facade contained results.To address this problem,a pixel-by-pixel digital differential rectification-based automatic DOM generation method is proposed in this paper.Firstly,3D point clouds with texture are generated by dense image matching based on an optical flow field for a stereo pair of images,respectively.Then,the grayscale of the digital differential rectification image is extracted directly from the point clouds element by element according to the nearest neighbor method for matched points.Subsequently,the elevation is repaired grid-by-grid using the multi-layer Locally Refined B-spline(LR-B)interpolation method with triangular mesh constraint for the point clouds void area,and the grayscale is obtained by the indirect scheme of digital differential rectification to generate the pixel-by-pixel digital differentially rectified image of a single image slice.Finally,a seamline network is automatically searched using a disparity map optimization algorithm,and DOM is smartly mosaicked.The qualitative and quantitative experimental results on three datasets were produced and evaluated,which confirmed the feasibility of the proposed method,and the DOM accuracy can reach 1 Ground Sample Distance(GSD)level.The comparison experiment with the state-of-the-art commercial softwares showed that the proposed method generated DOM has a better visual effect on building boundaries and roof completeness with comparable accuracy and computational efficiency.
基金Supported by the National Natural Science Foundation of China under Grant No 51305033the Ministry of National Defense of China under Grant No 9140C340506
文摘An analytical simulation based on a new model incorporating surface interaction is conducted to study the slip phenomenon in the Couette flow at different scales. The velocity profile is calculated by taking account of the micro-force between molecules and macro-force from the viscous shearing effect, as they contribute to the achieve- ment of the slip length. The calculated results are compared with those obtained from the molecular dynamics simulation, showing an excellent agreement. Further, the effect of the shear rate on the slip is investigated. The results can well predict the fluid flow behaviors on a solid substrate, but has to be proved by experiment.
文摘The drift-flux model has a practical importance in two-phase flow analysis.In this study,a finite volume solution is developed for a transient four-equation drift-flux model through the staggered mesh,leading to the development of a fully implicit discretization method.The main advantage of the fully implicit method is its unconditional stability.Newton's scheme is a popular method of choice for the solution of a nonlinear system of equations arising from fully implicit discretization of field equations.However,the lack of convergence robustness and the construction of Jacobian matrix have created several difficulties for the researchers.In this paper,a fully implicit model is developed based on the SIMPLE algorithm for two-phase flow simulations.The drawbacks of Newton's method are avoided in the developed model.Different limiter functions are considered,and the stabilized method is developed under steady and transient conditions.The results obtained by the numerical modeling are in good agreement with the experimental data.As expected,the results prove that the developed model is not restricted by any stability limit.
基金Supported by the National Key R&D Program of China under Grant No 2016YFB0400104
文摘Metal organic chenlical vapor deposition （AIOCVD） growth systems arc one of the. main types of equipment used for growing single crystal materials, such as GaN. To obtain fihn epitaxial materials with uniform performanee, the flow field and ternperature field in a GaN-MOCVD reactor are investigated by modeling and simulating. To make the simulation results more consistent with the actual situation, the gases in the reactor are considered to be compressible, making it possible to investigate the distributions of gas density and pressure in the reactor. The computational fluid dynamics method is used to stud,v the effects of inlet gas flow velocity, pressure in the reactor, rotational speed of graphite susceptor, and gases used in the growth, which has great guiding~ significance for the growth of GaN fihn materials.
文摘A combined characteristic-based split algorithm and all adaptive meshing technique for analyzing two-dimensional viscous incompressible flow are presented. Tile method uses the three-node triangular element with equal-order interpolation functions for all variables of tile velocity components and pressure. The main advantage of the combined nlethod is that it inlproves the sohltion accuracy by coupling an error estinla- tion procedure to an adaptive meshing technique that generates small elements in regions with a large change ill sohmtion gradients, mid at the same time, larger elements in the other regions. The performance of the combined procedure is evaluated by analyzing one test case of the flow past a cylinder, for their transient and steady-state flow behaviors.
文摘The isolation and culture of conventional detection method of salmonella can not meet the testing requirements of quick and easy detection at the grassroots level. In this study, we prepare the fluorescent nanoparticles as a marker, covalently conjugate with monoclonal antibodies of Salmonella pullorum. The whole Salmonella pullorum antigen and goat anti-mouse antibody sprayed on the nitrocellulose membranes are used as test line and control line. The fluorescence nanoparticles immune based lateral flow strips are made according to the principle of antigen-antibody immune response. The test strips may interpret results within 30 min. The results of the salmonella A, S. agona, S. chester and S. arechavaleta are positive, including, S. agona for weakly positive. After analysis, it is found that in addition to the salmonella of group A, the other positive salmonella are in group B. But it is negative of S. derby, S. rissen, and other 6 kinds of salmonella, with good specificity. The fluorescence nanoparticles immune based lateral flow strips are a little of sample can be detected fast, easily, inexpensive, easy to universal without professional technical personnel detection method. It provides a new detection method for the detections of Salmonella pullorum.
基金supported by the National Natural Science Foundation of China (10772050)
文摘A new video-based measurement is proposed to collect and investigate traffic flow parameters. The output of the measurement is velocity-headway distance data pairs. Because density can be directly acquired by the reciprocal of headway distance, the data pairs have the advantage of better simultaneity than those from common detectors. By now, over 33 000 pairs of data have been collected from two road sections in the cities of Shanghai and Zhengzhou. Through analyzing the video files recording traffic movements on urban expressways, the following issues are studied：laws of vehicle velocity changing with headway distance, proportions of di0erent driving behaviors in the traffic system, and characteristics of traffic flow in snowy days. The results show that the real road traffic is very complex, and factors such as location and climate need to be taken into consideration in the formation of traffic flow models.
基金This research was done as part of TEKES-funded PanFlow project and as part of a project OPTIMI funded by the Academy of Finland (grant number 117587) in Micro- and Nanosystems Research Group, Tampere University of Technology, Finland.
文摘When characterizing flows in miniaturized channels, the determination of the dynamic contact angle is important. By measuring the dynamic contact angle, the flow properties of the flowing liquid and the effect of material properties on the flow can be characterized. A machine vision based system to measure the contact angle of front or rear menisci of a moving liquid plug is described in this article. In this research, transparent flow channels fabricated on thermoplastic polymer and sealed with an adhesive tape are used. The transparency of the channels enables image based monitoring and measurement of flow variables, including the dynamic contact angle. It is shown that the dynamic angle can be measured from a liquid flow in a channel using the image based measurement system. An image processing algorithm has been developed in a MATLAB environment. Images are taken using a CCD camera and the channels are illuminated using a custom made ring light. Two fitting methods, a circle and two parabolas, are experimented and the results are compared in the measurement of the dynamic contact angles.
基金The National Natural Science Foundation of China under contract No. 40774033863 Program under contract No. 2006AA09A203-05973 Program under contract No. 2009CB219503
文摘Using the collected 433 heat flow values, we estimated the bases of methane hydrate stability zone （BHSZ）, in northern South China Sea （NSCS）. Through comparing BHSZs with the depths of bottom simulating reflectors （BSRs）, in Shenhu Area （SA）, we found that there are big differences between them. In the north of SA, where the water depth is shallow, many slumps developed and the sedimentation rate is high, it appears great negative difference （as large as -192%）. However, to the southeast of SA, where the water depth is deeper, sedimentation rate is relatively low and uplift basement topography exists, it changes to positive difference （as large as ＋45%）. The differences change so great, which haven＇t been observed in other places of the world. After considering the errors from the process of heat flow measurement, the BSR depth, the relationship of thermal conductivity with the sediments depth, and the fluid flow activities, we conclude that the difference should be not caused by these errors. Such big disagreement may be due to the misunderstanding of BSR. The deviant ＂BSRs＂ could represent the paleo-BSRs or just gas-bearing sediment layers, such as unconformities or the specific strata where have different permeability, which are not hydraterelated BSRs.
文摘To enhance the applicability and measurement accuracy of phase-based optical flow method using complex steerable pyramids in structural displacement measurement engineering applications, an improved method of optimizing parameter settings is proposed. The optimized parameters include the best measurement points of the Region of Interest (ROI) and the levels of pyramid filters. Additionally, to address the issue of updating reference frames in practical applications due to the difficulty in estimating the maximum effective measurement value, a mechanism for dynamically updating reference frames is introduced. Experimental results demonstrate that compared to representative image gradient-based displacement measurement methods, the proposed method exhibits higher measurement accuracy in engineering applications. This provides reliable data support for structural damage identification research based on vibration signals and is expected to broaden the engineering application prospects for structural health monitoring.
文摘In this work, we study the characteristics I-V and P-V of a silicon solar cell as well as its fill factor, its electrical power from the optimum thickness obtained in the base under variation of the irradiation energy flow of charged particles. The recombination velocity at the junction corresponding to the maximum power point was also deduced.
文摘The experimental investigation of unsteady complex flow fields in wind tunnels requires advanced measurement techniques. The most important of such image based measurement techniques are those for the measurement of planar flow velocity fields, planar pressure distribution, model location and deformation, model temperature and quantitative high speed flow visualization. The applications as carried out by DLR range from low speed flows to transonic flows, from high lift configurations to propellers and rotors, from wake vortex investigations in catapult facilities and water towing tanks to investigations of vortex break down phenomena on delta wings. The capability to use image based measurement techniques in transonic flows requires dedicated technical developments and experienced scientists due to the special environment of a transonic wind tunnel. In this paper an overview of the state-of-the art of the application of image based measurement techniques in transonic flows as performed by DLR＇s Institute of Aerodynamics and Flow Technology will be given.
文摘In the present study,the base pressure variations induced by the presence of a cavity,known to have a strong influence of the behaviour of supersonic projectiles,are investigated through numerical solution of the balance equations for mass,momentum,and energy.An area ratio of four is considered and numerical simulations are carried out at Mach M=1.2,1.4,1.6,and 1.8 assuming no cavity or cavity locations 0.5D,1D,1.5D,and 2D.The inlet pressure of the nozzle is considered as a flow variable.The Taguchi method is also used,and the considered cases are then analyzed using a full factorial experimental design.The results show that the cavity is effective in increasing the base pressure for the conditions examined.For other nozzle pressure ratios,cavities do not lead to passive control due the change in the reattachment length.The distribution of wall pressure reveals that,in general,a cavity used to implement passive control of the base pressure does not adversely influence the flow pattern in the domain.
