Steel cylindrical shells are widely used in engineering structures due to their high strength-to-weight ratio,but they are vulnerable to buckling under axial loads.To address this limitation,fiber-reinforced polymer(F...Steel cylindrical shells are widely used in engineering structures due to their high strength-to-weight ratio,but they are vulnerable to buckling under axial loads.To address this limitation,fiber-reinforced polymer(FRP)composites have emerged as promising materials for structural reinforcement.This study investigates the buckling behavior of steel cylindrical shells reinforced with inner and outer layers of polymer composite materials under axial compression.Using analytical and numerical modeling methods,the critical buckling loads for different reinforcement options were evaluated.Two-sided glass fiber reinforced plastic(GFRP)or carbon fiber reinforced plastic(CFRP)coatings,as well as combined coatings with layers of different composites,were considered.GFRP+CFRPIn the calculations,the coatings were treated as homogeneous orthotropic materials with equivalent averaged elastic characteristics.The numerical analysis revealed that CFRP reinforcement achieved the highest increase in buckling load,with improvements ranging from 9.84%to 47.29%,depending on the composite thickness and steel shell thickness.GFRP reinforcement,while beneficial,demonstrated a lower effectiveness,with buckling load increases between 5.89%and 19.30%.The hybrid reinforcement provided an optimal balance,improving buckling resistance by GFRP+CFRP6.94%to 43.95%.Statistical analysis further identified composite type and thickness as the most significant factors affecting buckling performance.The findings suggest that CFRP is the preferred reinforcement material,especially when applied to thin-walled cylindrical shells,while hybrid reinforcements can be effectively utilized for structures requiring a balance between stiffness and ductility.These insights provide a foundation for optimizing FRP reinforcement strategies to enhance the structural integrity of steel shells in engineering applications.展开更多
Post stall behaviors of a single stage compression system are studied theoretically and experimentally in this paper. A one dimensional nonlinear model, which is able to describe the dynamically post stall behavio...Post stall behaviors of a single stage compression system are studied theoretically and experimentally in this paper. A one dimensional nonlinear model, which is able to describe the dynamically post stall behaviors of the compression system, is applied to simulate the post stall behaviors digitally. The stall types, i.e. , rotating stall and surge, are determined. The variations of annular average parameters while the compression system goes into stall are also calculated exactly. The post stall behaviors are measured on the single stage compressor test rig. The measurement shows that rotating stall and surge appear under different conditions. On the basis of experiments, it is found that the post stall behaviors are influenced remarkably by some factors, such as rotation speeds, construction type and size of the exhaust duct. Good agreement between the simulation and experiments proves that this modeling technique is valid for simulating the post stall behaviors.展开更多
The volumetric strain was categorized into elastic and plastic parts. The farmer camposed of axial and lateral strains is uniform and determined by Hooke＇s law ; however, the latter consisting of axial and lateral st...The volumetric strain was categorized into elastic and plastic parts. The farmer camposed of axial and lateral strains is uniform and determined by Hooke＇s law ; however, the latter consisting of axial and lateral strains is a fuaction af thickness af shear band determined by grndieat-dependeat plasticity by cansidering the heterngeneity of quasi- brittle materials. The non- uniform lateral strain due to the fact that shear band was farmed in the middle of specimen was averaged within specimen to precisely assess the volumetric strain. Then, the analytical expression for volumetric strain was verified by comparison with two earlier experimental results for concrete and rack. Finally, a detailed parametric study was carried out to investigate effects of constitutive parameters （ shear band thickness, elastic and softening rnoduli ） and geometrical size of specimen（ height and width of specimen ） on the volume dilatancy.展开更多
Based on the characteristics of an L-shaped column composed of concrete-filled square steel tubes, the axial compression experiment and nonlinear finite element analysis were carried out to study the mechanical proper...Based on the characteristics of an L-shaped column composed of concrete-filled square steel tubes, the axial compression experiment and nonlinear finite element analysis were carried out to study the mechanical property of the L-shaped column. The load-displacement curve for the L-shaped column, the deflection and load-strain curves for the mono columns were obtained by the axial compression experiment. The results show that the L-shaped column exhibits a flexural-torsional buckling failure mode. The numerical simulation by the finite element analysis shows that the bearing capacity and failure mode are in accordance with those of the axial compression experiment and the feasi- bility of the finite element analysis is proved. For the calculation of the bearing capacity of the L-shaped column com- posed of concrete-filled square steel tubes, an analytical method is proposed based on the theory of the elastic stability and spatial truss model. The results of the analytical method are in good agreement with those of the axial compression experiment and the finite element analysis.展开更多
Since fibre-reinforced polymer(FRP) and stainless steel(SS) offer advantages of corrosion resistance and hybrid confinement, this study proposed a new type of composite column: sea sand concrete(SSC)-filled SS tubular...Since fibre-reinforced polymer(FRP) and stainless steel(SS) offer advantages of corrosion resistance and hybrid confinement, this study proposed a new type of composite column: sea sand concrete(SSC)-filled SS tubular columns with an inner FRP tube(CFSTFs) to help exploit abundant ocean resources in marine engineering. To study compressive behaviours of these novel members, eight CFSTFs and two SSC-filled SS tubular columns(CFSTs)were tested under axial compression. Their axial load-displacement curves, axial load-strain curves in SS or FRP tubes were obtained, and influences of key test parameters(the existence of glass FRP(GFRP) tubes, steel tube shapes, and GFRP tube thicknesses and diameters) were discussed. Further, specimen failure mechanism was analyzed employing the finite element method using ABAQUS software. Test results confirmed the excellent ductility and load-bearing capacity of CFSTFs. The existence of GFRP tubes inside can postpone SS tube buckling, and the content of inner FRP tubes, particularly increasing diameters, was found to improve compressive behaviours. GFRP contents helped develop the second elastic-plastic stage of the load-displacement curves. Furthermore, the bearing capacity of CFSTFs with a circular cross-section was approximately 26% higher than that with a square cross-section, and this difference narrowed with the increase in GFRP ratios.展开更多
A stiffened cylindrical shell is normally used in refuge chambers of a coal mine. Based on the method of application and shape characteristics of a refuge chamber, we simplified its shell as an orthotropic cylinder. T...A stiffened cylindrical shell is normally used in refuge chambers of a coal mine. Based on the method of application and shape characteristics of a refuge chamber, we simplified its shell as an orthotropic cylinder. The basic buckling equation of the stiffened cylindrical shell under uniform axial compression was deduced by using a Donnell function. The factors affecting its buckling capacity were studied by theoretical analysis and numerical calculations. The results reveal that the torsional rigidity of the longitudinal stiffener had little effect on the buckling capacity of the shell and that the critical load of an externally stiffened cylindrical shell is higher than that of an internally stiffened cylindrical shell.展开更多
This paper seeks to outline the temperature effect on the buckling properties of ultra-thin-walled lenticular collapsible composite tube（LCCT） subjected to axial compression.The buckling tests of the LCCT specimens ...This paper seeks to outline the temperature effect on the buckling properties of ultra-thin-walled lenticular collapsible composite tube（LCCT） subjected to axial compression.The buckling tests of the LCCT specimens subjected to axial compression were carried out on INSTRON-500 N servo-hydraulic machine in dry state and at the temperatures of 25 C, 100 C and 80 C. The load–displacement curves and buckling initiation loads were measured and the buckling initiation mechanism was discussed from experimental observations. Experiments show that the buckling initiation load, on average, is only about 2.2% greater at the low temperature of 80 C than at the room temperature of 25 C due to the material hardening, demonstrating an insignificant increase in the buckling initiation load, whereas it is about 19.5% lower at the high temperature of 100 C than at the room temperature owing to the material softening, implying a significant decrease in the buckling initiation load. The failure mode of the LCCT in axial compression tests at three different temperatures can be reckoned to be characteristic of the buckling initiation and propagation around the central region until rupture. The finite element（FE） model is presented to simulate the buckling initiation mechanism based on the eigenvalue-based methodology. Good correlation between experimental and numerical results is achieved.展开更多
Although smoothness, softness, and stiffness determine the physical and mechanical behavior of a fabric and the subjective assessment of quality when it is handled, the perceived comfort of clothing is more important ...Although smoothness, softness, and stiffness determine the physical and mechanical behavior of a fabric and the subjective assessment of quality when it is handled, the perceived comfort of clothing is more important to consumers. The sensations perceived from the contact of clothing with the skin can greatly influence our over-all state of comfort and one aspect of this is the unpleasant skin sensation of prickle. Surface prickle of fabrics can be a factor limiting the use of the coarser types of ramie in apparel. And the mechanical stimulus of fabric-evoked prickle underlies our discomfort to fabrics independent in the majority of cases of any chemical or the atopic status of the individual. It is known that the prickle of fabric can be reduced by fabric-finishing treatments, but the assessment of fabric prickle is often done subjectively. This is time consuming, and it is difficult to obtain reliable and reproducible results, since variability between subjects in their sensitivity to prickle, such as skin mechanical properties, effective density of nociceptors and the mood state of the individual. In order to find an objective method of measuring the physical properties of the stiff fiber ends protruding from the fabrics to predict prickle, axial compression bending tests were examined by using single ramie fiber. By comparing analysis, it is found that the critical compressing load (Pcr), the bending modulus (E) are the important parameters. The relationship of the critical load (Pcr) with the length of fiber (L) and the fineness of fiber (Nt) has been investigated.展开更多
The static tests of nine traditional and bird beak square hollow structure(SHS) T-joints with different β values and connection types under axial compression at brace end were carried out. Experimental test schemes, ...The static tests of nine traditional and bird beak square hollow structure(SHS) T-joints with different β values and connection types under axial compression at brace end were carried out. Experimental test schemes, failure modes of specimens, jack load-vertical displacement curves, jack load-deformation of chord and strain intensity distribution curves of joints were presented. The effects of β and connection types on axial compression property of joints were studied. The results show that the ultimate axial compression capacity of common bird beak SHS T-joints and diamond bird beak SHS T-joints is larger than that of traditional SHS T-joint specimens with big values of β. The ultimate axial compression capacity of diamond bird beak SHS T-joints is larger than that of common bird beak SHS T-joints. As β increases, the increase of the ultimate axial compression capacity of diamond bird beak SHS T-joints over that of common bird beak joints grows. The ultimate axial compression capacity and the initial axial stiffness of all kinds of joints increase as β increases, and the initial axial stiffness of the diamond bird beak SHS T-joints is the largest. The ductilities of common bird beak and diamond bird beak SHS T-joints increase as β increases, but the ductility of the traditional SHS T-joints decreases as β increases.展开更多
Based on the constancy hypothesis of material volume, the circumferential and radial stresses of a cylinder specimen are analyzed when the cylinder is subject to a loading along the axial direction. The circumferentia...Based on the constancy hypothesis of material volume, the circumferential and radial stresses of a cylinder specimen are analyzed when the cylinder is subject to a loading along the axial direction. The circumferential and radial stress distribution is a power function of radius parameter when the constitutive relation of specimen material is orthotropic. The stress distribution is a quadratic function of radius parameter for transversely isotropic material. Along the cylinder axial line, the circumferential and radial stresses are maximum and equal to each other. In the circumference boundary surface, the radial stress is zero and the circumferential stress value is minimal. The failure theory of maximum tensile circumferential strain is applied to calculate the critical axial loading. The circumference-boundary-layer failure criterion of orthotropic cylinders is described with the Hill-Tsai strength theory. The obtained strength theory is related to axial stress and mechanical properties of specimen material and to the specimen axialdeformation strain rate and the change rate of strain rate.展开更多
An investigation is conducted on the static ultimate limit state assessment of ship hull plates with elastically restrained edges subjected to axial compression.Both material and geometric non-linearities were conside...An investigation is conducted on the static ultimate limit state assessment of ship hull plates with elastically restrained edges subjected to axial compression.Both material and geometric non-linearities were considered in finite element(FE)analysis.The initial geometric imperfection of the plate was considered,while the residual stress introduced by welding was not considered.The ultimate strength of simply supported ship hull plates compared well with the existing empirical formula to validate the correctness of the applied boundary conditions,initial imperfection and mesh size.The extensive FE calculations on the ultimate strength of ship hull plates with elastically restrained edges are presented.Then a new simple empirical formula for plate ultimate strength is developed,which includes the effect of the rotational restraint stiffness,rotational restraint stiffness,and aspect ratios.By applying the new formula and FE method to ship hull plates in real ships,a good coincidence of the results between these two methods is obtained,which indicates that the new formula can accurately predict the ultimate strength of ship hull plates with elastically restrained edges.展开更多
Field reversed configuration(FRC)is widely considered as an ideal target plasma for magnetoinertial fusion.However,its confinement and stability,both proportional to the radius,will deteriorate inevitably during radia...Field reversed configuration(FRC)is widely considered as an ideal target plasma for magnetoinertial fusion.However,its confinement and stability,both proportional to the radius,will deteriorate inevitably during radial compression.Hence,we propose a new fusion approach based on axial compression of a large-sized FRC.The axial compression can be made by plasma jets or plasmoids converging onto the axial ends of the FRC.The parameter space that can reach the ignition condition while preserving the FRC's overall quality is studied using a numerical model based on different FRC confinement scalings.It is found that ignition is possible for a large FRC that can be achieved with the current FRC formation techniques if compression ratio is greater than 50.A more realistic compression is to combine axial with moderate radial compression,which is also presented and calculated in this work.展开更多
In this paper,a new type of bamboo scrimber column embedded with steel bars(rebars)was proposed,and the compression performance was improved by pre-embedding rebars during the preparation of the columns.The effects of...In this paper,a new type of bamboo scrimber column embedded with steel bars(rebars)was proposed,and the compression performance was improved by pre-embedding rebars during the preparation of the columns.The effects of the slenderness ratio and the reinforcement ratio on the axial compression performance of reinforced bamboo scrimber columns were studied by axial compression tests on 28 specimens.The results showed that the increase in the slenderness ratio had a significant negative effect on the axial compression performance of the columns.When the slenderness ratio increased from 19.63 to 51.96,the failure mode changed from strength failure to buckling failure,and the maximum bearing capacity decreased by 43.03%.The axial compression performance of the reinforced bamboo scrimber columns did not significantly improve at a slenderness ratio of 19.63,but the opposite was true at slenderness ratios of 36.95 and 51.96.When the reinforcement ratio increased from 0%to 4.52%,the bearing capacity of those with a slenderness ratio of 51.96 increased by up to 16.99%,and the stiffness and ductility were also improved.Finally,based on existing specifications,two modification parameters,the overall elastic modulus Ec and the combined strength fcc,were introduced to establish a calculation method for the bearing capacity of the reinforced bamboo scrimber columns.The calculation results were compared with the test results,and the results showed that the proposed calculation models can more accurately predict the bearing capacity.展开更多
Stability analyses of perfect and imperfect cylindrical shells under axial compression and torsion were presented. Finite element method for the stability analysis of perfect cylindrical shells was put forward through...Stability analyses of perfect and imperfect cylindrical shells under axial compression and torsion were presented. Finite element method for the stability analysis of perfect cylindrical shells was put forward through comparing critical loads and the first buckling modes with those obtained through theoretical analysis. Two typical initial defects, non-circularity and uneven thickness distribution, were studied. Critical loads decline with the increase of non-circularity, which exist in imperfect cylindrical shells under both axial compression and torsion. Non-circularity defect has no effect on the first buckling mode when cylindrical shell is under torsion. Unfortunately, it has a completely different buckling mode when cylindrical shell is under axial compression. Critical loads decline with the increase of thickness defect amplitude, which exist in imperfect cylindrical shells under both axial compression and torsion, too. A greater wave number is conducive to the stability of cylindrical shells. The first buckling mode of imperfect cylindrical shells under torsion maintains its original shape, but it changes with wave number when the cylindrical shell is under axial compression.展开更多
In recent years,cold-formed steel(CFS)built-up sections have gained a lot of attention in construction.This is mainly because of their structural efficiency and the design advantages they offer.They provide better loa...In recent years,cold-formed steel(CFS)built-up sections have gained a lot of attention in construction.This is mainly because of their structural efficiency and the design advantages they offer.They provide better loadbearing strength and show greater resistance to elastic instability.This study looks at both experimental and numerical analysis of built-up CFS columns.The columns were formed by joining two C-sections in different ways:back-to-back,face-to-face,and box arrangements.Each type was tested with different slenderness ratios.For the experiments,the back-to-back and box sections were connected using two rows of rivets.The face-to-face sections,on the other hand,were joined by welding.In order to improve axial strength and overall stability,all column samples were filled with ordinary concrete,conforming to class C25/30.The numerical modeling was done in ABAQUS to study themechanical behavior of the columns.This helped in understanding how different joining methods affect their axial compression performance.Analytical checkswere also carried out using Eurocode 3 for hollowsections and Eurocode 4 for concretefilled sections.The role of concrete confinement was examined as well,following American Concrete Institute(ACI)guidelines,for both face-to-face and box-shaped columns.Thenumerical results matched closely with the experimental findings,with variations of less than 5%.The study identified key failure modes such as local buckling and distortional buckling.It highlighted how section shape,type of connection,and concrete infill all play amajor role in improving the strength of built-up CFS columns.展开更多
In order to study the axial compression characteristics of brick masonry historical buildings, and to better protect and repair traditional mortar-brick masonry historical buildings, axial compression tests were carri...In order to study the axial compression characteristics of brick masonry historical buildings, and to better protect and repair traditional mortar-brick masonry historical buildings, axial compression tests were carried out on three kinds of restored mortar (pure mud mortar, pure mortar, and mud mortar) brick masonry with restored mortar brick masonry as the object of study. The damage modes, axial compression chemical indexes (compressive strength and elastic modulus), load-displacement curves and stress-strain curves of the three kinds of restored mortar brick masonry were obtained. The experimental results show that the compressive strength of mud mortar brick masonry of 1.676 MPa is better than that of pure mud 1.530 MPa and pure mortar 1.471 MPa brick masonry, which is due to the difference in the bond effect between the restored mortar material and the brick block. According to the test results, the compressive strength formula of the restored mortar brick masonry was modified, and the reasons for the difference between the experimental value of the modulus of elasticity of the restored mortar brick masonry and that of the traditional formula and the measured value were compared and analyzed by a factor of 6.73–7.1. Referring to the axial-pressure ontological relationship of the conventional brick masonry, the 4-parameter segmental function expression was proposed for the characterization of the stress-strain relationship of the restored mortar brick masonry with the use of the stress-strain normalization process. The research results provide theoretical support for the inheritance and development of traditional mortar brick masonry historical architecture.展开更多
Tube thinning control without wrinkling occurring is a key problem urgently to be solved for improving the forming qualities in numerical control （NC） bending processes of large-diameter Al-alloy thin-walled tubes ...Tube thinning control without wrinkling occurring is a key problem urgently to be solved for improving the forming qualities in numerical control （NC） bending processes of large-diameter Al-alloy thin-walled tubes （AATTs）. It may be a way solving this problem to exert axial compression loads （ACL） on the tube end in the bending. Thus, this article establishes a three-dimensional （3D） elastic-plastic explicit finite element （FE） model for the bending under ACL and has its reliability verified. Through a multi-index orthogonal experiment design, a combination of process parameters, each expressed by a proper range, for this FE model is derived to overcome the compression instability on tube ends. By combining the FE model with a wrinkling energy prediction model, an in-depth study is conducted on the forming characteristics of large-diameter AATTs with small bending radii and it can be concluded that （1） The larger the tube diameters and the smaller the bending radii, the larger the induced tangent tension stress zones on tube intrados, by which the tube maximum tangent compression stress zones will be partitioned in the bending processes; thus, the smaller the ACL roles in decreasing thinning degrees and the larger the compression instability possibilities on tube ends. （2） The tube wrinkling possibilities under ACL are larger than without ACL acting in the earlier forming periods, and smaller in the later ones. （3） For the tubes with a size factor less than 80, the ACL roles in decreasing thinning degrees are stronger than in increasing wrinkling possibilities.展开更多
To enhance the deformation capacity of vertical support columns of underground structures and improve their overall seismic performance,a new truncated column connected by unbonded prestressed tendons is proposed,insp...To enhance the deformation capacity of vertical support columns of underground structures and improve their overall seismic performance,a new truncated column connected by unbonded prestressed tendons is proposed,inspired by the concepts of the toughness seismic resistance and rocking design.Although many experimental and numerical studies have focused on underground structures,research on the behavior of truncated columns remains limited.This paper develops threedimensional(3D)finite element(FE)models for various columns,including cast-in-place column(CIPC)and prestressed tendon truncated column(PTTC),to evaluate the effects of three parameters,including axial compression ratio(ACR),initial tendon stress,and the effect of hole diameter on mechanical performance—specifically deformation capacity,strength,residual deformation and gap width.The results indicate that the deformability and self-centering ability of the prestressed tendon truncated column is obviously superior to the cast-in-place column,but its strength was comparatively lower.The axial compression ratio has obvious effects on seismic performance,especially deformation and residual deformation,while initial tendon stress and hole diameter influence performance only in the case of a small axial compression ratio.This study systematically identifies the influence of various factors on seismic performance.Additionally,this study proposes a method to evaluate the self-centering capability of structures and establishes an empirical relationship between maximum recoverable deformation and the axial compression ratio.The developed numerical model can serve as a tool for future studies to predict the seismic responses of overall subway stations that feature truncated columns.展开更多
This paper provides a review of recent research advances and trends in the area of stability of unstiffened circular cylindrical shells subjected to general non-uniform axial compressive stresses.Only the more importa...This paper provides a review of recent research advances and trends in the area of stability of unstiffened circular cylindrical shells subjected to general non-uniform axial compressive stresses.Only the more important and interesting aspects of the research,judged from a personal viewpoint,are discussed.They can be crudely classified into four categories:(1) shells subjected to non-uniform loads;(2) shells on discrete supports;(3) shells with intended cutouts/holes;and (4) shells with non-uniform settlements.展开更多
The axial bearing capacity of prefabricated composite walls composed of inner and outer concrete wythes,expandable polystyrene(EPS)boards and steel sleeve connectors is investigated.An experimental study on the axial ...The axial bearing capacity of prefabricated composite walls composed of inner and outer concrete wythes,expandable polystyrene(EPS)boards and steel sleeve connectors is investigated.An experimental study on the axial bearing capacity of four prefabricated composite walls after fire treatment is carried out.Two of the prefabricated composite walls are normal-temperature specimens,and the others are treated with fire.The damage modes and crack development are observed,and the axial bearing capacity,lateral deformation of the specimens,and the concrete and reinforcing bar strain are tested.The results show that the ultimate bearing capacity of specimens after a fire is less than that of normal-temperature specimens;when the insulation board thicknesses are 40 mm and 60 mm,the decrease amplitudes are 20.8%and 16.8%,respectively.The maximum lateral deformation of specimens after a fire is greater than that of normal-temperature specimens,and under the same level of load,the lateral deformation increases as the insulation board thickness increases.Moreover,the strain values of the concrete and reinforcing bars of specimens after a fire are greater than those of normal-temperature specimens,and the strain values increase as the thickness of insulation board increases.展开更多
文摘Steel cylindrical shells are widely used in engineering structures due to their high strength-to-weight ratio,but they are vulnerable to buckling under axial loads.To address this limitation,fiber-reinforced polymer(FRP)composites have emerged as promising materials for structural reinforcement.This study investigates the buckling behavior of steel cylindrical shells reinforced with inner and outer layers of polymer composite materials under axial compression.Using analytical and numerical modeling methods,the critical buckling loads for different reinforcement options were evaluated.Two-sided glass fiber reinforced plastic(GFRP)or carbon fiber reinforced plastic(CFRP)coatings,as well as combined coatings with layers of different composites,were considered.GFRP+CFRPIn the calculations,the coatings were treated as homogeneous orthotropic materials with equivalent averaged elastic characteristics.The numerical analysis revealed that CFRP reinforcement achieved the highest increase in buckling load,with improvements ranging from 9.84%to 47.29%,depending on the composite thickness and steel shell thickness.GFRP reinforcement,while beneficial,demonstrated a lower effectiveness,with buckling load increases between 5.89%and 19.30%.The hybrid reinforcement provided an optimal balance,improving buckling resistance by GFRP+CFRP6.94%to 43.95%.Statistical analysis further identified composite type and thickness as the most significant factors affecting buckling performance.The findings suggest that CFRP is the preferred reinforcement material,especially when applied to thin-walled cylindrical shells,while hybrid reinforcements can be effectively utilized for structures requiring a balance between stiffness and ductility.These insights provide a foundation for optimizing FRP reinforcement strategies to enhance the structural integrity of steel shells in engineering applications.
文摘Post stall behaviors of a single stage compression system are studied theoretically and experimentally in this paper. A one dimensional nonlinear model, which is able to describe the dynamically post stall behaviors of the compression system, is applied to simulate the post stall behaviors digitally. The stall types, i.e. , rotating stall and surge, are determined. The variations of annular average parameters while the compression system goes into stall are also calculated exactly. The post stall behaviors are measured on the single stage compressor test rig. The measurement shows that rotating stall and surge appear under different conditions. On the basis of experiments, it is found that the post stall behaviors are influenced remarkably by some factors, such as rotation speeds, construction type and size of the exhaust duct. Good agreement between the simulation and experiments proves that this modeling technique is valid for simulating the post stall behaviors.
基金Funded by the National Natural Science Foundation of China(No.50309004)
文摘The volumetric strain was categorized into elastic and plastic parts. The farmer camposed of axial and lateral strains is uniform and determined by Hooke＇s law ; however, the latter consisting of axial and lateral strains is a fuaction af thickness af shear band determined by grndieat-dependeat plasticity by cansidering the heterngeneity of quasi- brittle materials. The non- uniform lateral strain due to the fact that shear band was farmed in the middle of specimen was averaged within specimen to precisely assess the volumetric strain. Then, the analytical expression for volumetric strain was verified by comparison with two earlier experimental results for concrete and rack. Finally, a detailed parametric study was carried out to investigate effects of constitutive parameters （ shear band thickness, elastic and softening rnoduli ） and geometrical size of specimen（ height and width of specimen ） on the volume dilatancy.
基金Foundation of Key Laboratory of Coast Civil Structure Safety (Tianjin University),Ministry of EducationChinese Program for New Century Excellent Talents in University+1 种基金Seed Foundation of Tianjin UniversitySeed Foundation of Xinjiang University
文摘Based on the characteristics of an L-shaped column composed of concrete-filled square steel tubes, the axial compression experiment and nonlinear finite element analysis were carried out to study the mechanical property of the L-shaped column. The load-displacement curve for the L-shaped column, the deflection and load-strain curves for the mono columns were obtained by the axial compression experiment. The results show that the L-shaped column exhibits a flexural-torsional buckling failure mode. The numerical simulation by the finite element analysis shows that the bearing capacity and failure mode are in accordance with those of the axial compression experiment and the feasi- bility of the finite element analysis is proved. For the calculation of the bearing capacity of the L-shaped column com- posed of concrete-filled square steel tubes, an analytical method is proposed based on the theory of the elastic stability and spatial truss model. The results of the analytical method are in good agreement with those of the axial compression experiment and the finite element analysis.
基金financially supported by the Guangdong Basic and Applied Basic Research Foundation (Grant Nos. 2020A1515010095and 2023A1515010080)the Science and Technology Program of Guangzhou (Grant No. 202201010126)the Young Science and Technology Talent Support Project of Guangzhou Association for Science and Technology (Grant No. X20210201066)。
文摘Since fibre-reinforced polymer(FRP) and stainless steel(SS) offer advantages of corrosion resistance and hybrid confinement, this study proposed a new type of composite column: sea sand concrete(SSC)-filled SS tubular columns with an inner FRP tube(CFSTFs) to help exploit abundant ocean resources in marine engineering. To study compressive behaviours of these novel members, eight CFSTFs and two SSC-filled SS tubular columns(CFSTs)were tested under axial compression. Their axial load-displacement curves, axial load-strain curves in SS or FRP tubes were obtained, and influences of key test parameters(the existence of glass FRP(GFRP) tubes, steel tube shapes, and GFRP tube thicknesses and diameters) were discussed. Further, specimen failure mechanism was analyzed employing the finite element method using ABAQUS software. Test results confirmed the excellent ductility and load-bearing capacity of CFSTFs. The existence of GFRP tubes inside can postpone SS tube buckling, and the content of inner FRP tubes, particularly increasing diameters, was found to improve compressive behaviours. GFRP contents helped develop the second elastic-plastic stage of the load-displacement curves. Furthermore, the bearing capacity of CFSTFs with a circular cross-section was approximately 26% higher than that with a square cross-section, and this difference narrowed with the increase in GFRP ratios.
基金Financial support from the National Hi-tech Research and Development Program of China is much appreciated
文摘A stiffened cylindrical shell is normally used in refuge chambers of a coal mine. Based on the method of application and shape characteristics of a refuge chamber, we simplified its shell as an orthotropic cylinder. The basic buckling equation of the stiffened cylindrical shell under uniform axial compression was deduced by using a Donnell function. The factors affecting its buckling capacity were studied by theoretical analysis and numerical calculations. The results reveal that the torsional rigidity of the longitudinal stiffener had little effect on the buckling capacity of the shell and that the critical load of an externally stiffened cylindrical shell is higher than that of an internally stiffened cylindrical shell.
基金supported by the National Natural Science Foundation of China (Nos. 51075019 and 51375033)Aeronautical Science Foundation (No. 20095251024) of Chinathe Fundamental Research Funds for the Central Universities (No. YWF-13-T-RSC-121) of China
文摘This paper seeks to outline the temperature effect on the buckling properties of ultra-thin-walled lenticular collapsible composite tube（LCCT） subjected to axial compression.The buckling tests of the LCCT specimens subjected to axial compression were carried out on INSTRON-500 N servo-hydraulic machine in dry state and at the temperatures of 25 C, 100 C and 80 C. The load–displacement curves and buckling initiation loads were measured and the buckling initiation mechanism was discussed from experimental observations. Experiments show that the buckling initiation load, on average, is only about 2.2% greater at the low temperature of 80 C than at the room temperature of 25 C due to the material hardening, demonstrating an insignificant increase in the buckling initiation load, whereas it is about 19.5% lower at the high temperature of 100 C than at the room temperature owing to the material softening, implying a significant decrease in the buckling initiation load. The failure mode of the LCCT in axial compression tests at three different temperatures can be reckoned to be characteristic of the buckling initiation and propagation around the central region until rupture. The finite element（FE） model is presented to simulate the buckling initiation mechanism based on the eigenvalue-based methodology. Good correlation between experimental and numerical results is achieved.
文摘Although smoothness, softness, and stiffness determine the physical and mechanical behavior of a fabric and the subjective assessment of quality when it is handled, the perceived comfort of clothing is more important to consumers. The sensations perceived from the contact of clothing with the skin can greatly influence our over-all state of comfort and one aspect of this is the unpleasant skin sensation of prickle. Surface prickle of fabrics can be a factor limiting the use of the coarser types of ramie in apparel. And the mechanical stimulus of fabric-evoked prickle underlies our discomfort to fabrics independent in the majority of cases of any chemical or the atopic status of the individual. It is known that the prickle of fabric can be reduced by fabric-finishing treatments, but the assessment of fabric prickle is often done subjectively. This is time consuming, and it is difficult to obtain reliable and reproducible results, since variability between subjects in their sensitivity to prickle, such as skin mechanical properties, effective density of nociceptors and the mood state of the individual. In order to find an objective method of measuring the physical properties of the stiff fiber ends protruding from the fabrics to predict prickle, axial compression bending tests were examined by using single ramie fiber. By comparing analysis, it is found that the critical compressing load (Pcr), the bending modulus (E) are the important parameters. The relationship of the critical load (Pcr) with the length of fiber (L) and the fineness of fiber (Nt) has been investigated.
基金Projects(51278209,51478047)supported by the National Natural Science Foundation of ChinaProject(2014FJ-NCET-ZR03)supported by the Program for New Century Excellent Talents in Fujian Provincial Universities,China+1 种基金Project(JA13005)supported by the Incubation Program for Excellent Young Science and Technology Talents in Fujian Provincial Universities,ChinaProject(ZQN-PY110)supported by the Young and Middle-aged Academic Staff of Huaqiao University,China
文摘The static tests of nine traditional and bird beak square hollow structure(SHS) T-joints with different β values and connection types under axial compression at brace end were carried out. Experimental test schemes, failure modes of specimens, jack load-vertical displacement curves, jack load-deformation of chord and strain intensity distribution curves of joints were presented. The effects of β and connection types on axial compression property of joints were studied. The results show that the ultimate axial compression capacity of common bird beak SHS T-joints and diamond bird beak SHS T-joints is larger than that of traditional SHS T-joint specimens with big values of β. The ultimate axial compression capacity of diamond bird beak SHS T-joints is larger than that of common bird beak SHS T-joints. As β increases, the increase of the ultimate axial compression capacity of diamond bird beak SHS T-joints over that of common bird beak joints grows. The ultimate axial compression capacity and the initial axial stiffness of all kinds of joints increase as β increases, and the initial axial stiffness of the diamond bird beak SHS T-joints is the largest. The ductilities of common bird beak and diamond bird beak SHS T-joints increase as β increases, but the ductility of the traditional SHS T-joints decreases as β increases.
基金Project supported by the National Natural Science Foudation of China (No. 50874095)The Na-tional Basic Research Program of China (973 Program)
文摘Based on the constancy hypothesis of material volume, the circumferential and radial stresses of a cylinder specimen are analyzed when the cylinder is subject to a loading along the axial direction. The circumferential and radial stress distribution is a power function of radius parameter when the constitutive relation of specimen material is orthotropic. The stress distribution is a quadratic function of radius parameter for transversely isotropic material. Along the cylinder axial line, the circumferential and radial stresses are maximum and equal to each other. In the circumference boundary surface, the radial stress is zero and the circumferential stress value is minimal. The failure theory of maximum tensile circumferential strain is applied to calculate the critical axial loading. The circumference-boundary-layer failure criterion of orthotropic cylinders is described with the Hill-Tsai strength theory. The obtained strength theory is related to axial stress and mechanical properties of specimen material and to the specimen axialdeformation strain rate and the change rate of strain rate.
文摘An investigation is conducted on the static ultimate limit state assessment of ship hull plates with elastically restrained edges subjected to axial compression.Both material and geometric non-linearities were considered in finite element(FE)analysis.The initial geometric imperfection of the plate was considered,while the residual stress introduced by welding was not considered.The ultimate strength of simply supported ship hull plates compared well with the existing empirical formula to validate the correctness of the applied boundary conditions,initial imperfection and mesh size.The extensive FE calculations on the ultimate strength of ship hull plates with elastically restrained edges are presented.Then a new simple empirical formula for plate ultimate strength is developed,which includes the effect of the rotational restraint stiffness,rotational restraint stiffness,and aspect ratios.By applying the new formula and FE method to ship hull plates in real ships,a good coincidence of the results between these two methods is obtained,which indicates that the new formula can accurately predict the ultimate strength of ship hull plates with elastically restrained edges.
基金supported by National Natural Science Foundation of China(No.12175226)。
文摘Field reversed configuration(FRC)is widely considered as an ideal target plasma for magnetoinertial fusion.However,its confinement and stability,both proportional to the radius,will deteriorate inevitably during radial compression.Hence,we propose a new fusion approach based on axial compression of a large-sized FRC.The axial compression can be made by plasma jets or plasmoids converging onto the axial ends of the FRC.The parameter space that can reach the ignition condition while preserving the FRC's overall quality is studied using a numerical model based on different FRC confinement scalings.It is found that ignition is possible for a large FRC that can be achieved with the current FRC formation techniques if compression ratio is greater than 50.A more realistic compression is to combine axial with moderate radial compression,which is also presented and calculated in this work.
基金supported by the Resources Industry Science and Technology Innovation Joint Funding Project of Nanping City(N2021Z007)the Innovation Foundation for Doctoral Program of Forestry Engineering of Northeast Forestry University(LYGC202119).
文摘In this paper,a new type of bamboo scrimber column embedded with steel bars(rebars)was proposed,and the compression performance was improved by pre-embedding rebars during the preparation of the columns.The effects of the slenderness ratio and the reinforcement ratio on the axial compression performance of reinforced bamboo scrimber columns were studied by axial compression tests on 28 specimens.The results showed that the increase in the slenderness ratio had a significant negative effect on the axial compression performance of the columns.When the slenderness ratio increased from 19.63 to 51.96,the failure mode changed from strength failure to buckling failure,and the maximum bearing capacity decreased by 43.03%.The axial compression performance of the reinforced bamboo scrimber columns did not significantly improve at a slenderness ratio of 19.63,but the opposite was true at slenderness ratios of 36.95 and 51.96.When the reinforcement ratio increased from 0%to 4.52%,the bearing capacity of those with a slenderness ratio of 51.96 increased by up to 16.99%,and the stiffness and ductility were also improved.Finally,based on existing specifications,two modification parameters,the overall elastic modulus Ec and the combined strength fcc,were introduced to establish a calculation method for the bearing capacity of the reinforced bamboo scrimber columns.The calculation results were compared with the test results,and the results showed that the proposed calculation models can more accurately predict the bearing capacity.
基金Project(11102163)supported by the National Natural Science Foundation of ChinaProjects(JC20110218,JC20110260)supported by Foundation for Fundamental Research of Northwestern Polytechnical University,China
文摘Stability analyses of perfect and imperfect cylindrical shells under axial compression and torsion were presented. Finite element method for the stability analysis of perfect cylindrical shells was put forward through comparing critical loads and the first buckling modes with those obtained through theoretical analysis. Two typical initial defects, non-circularity and uneven thickness distribution, were studied. Critical loads decline with the increase of non-circularity, which exist in imperfect cylindrical shells under both axial compression and torsion. Non-circularity defect has no effect on the first buckling mode when cylindrical shell is under torsion. Unfortunately, it has a completely different buckling mode when cylindrical shell is under axial compression. Critical loads decline with the increase of thickness defect amplitude, which exist in imperfect cylindrical shells under both axial compression and torsion, too. A greater wave number is conducive to the stability of cylindrical shells. The first buckling mode of imperfect cylindrical shells under torsion maintains its original shape, but it changes with wave number when the cylindrical shell is under axial compression.
文摘In recent years,cold-formed steel(CFS)built-up sections have gained a lot of attention in construction.This is mainly because of their structural efficiency and the design advantages they offer.They provide better loadbearing strength and show greater resistance to elastic instability.This study looks at both experimental and numerical analysis of built-up CFS columns.The columns were formed by joining two C-sections in different ways:back-to-back,face-to-face,and box arrangements.Each type was tested with different slenderness ratios.For the experiments,the back-to-back and box sections were connected using two rows of rivets.The face-to-face sections,on the other hand,were joined by welding.In order to improve axial strength and overall stability,all column samples were filled with ordinary concrete,conforming to class C25/30.The numerical modeling was done in ABAQUS to study themechanical behavior of the columns.This helped in understanding how different joining methods affect their axial compression performance.Analytical checkswere also carried out using Eurocode 3 for hollowsections and Eurocode 4 for concretefilled sections.The role of concrete confinement was examined as well,following American Concrete Institute(ACI)guidelines,for both face-to-face and box-shaped columns.Thenumerical results matched closely with the experimental findings,with variations of less than 5%.The study identified key failure modes such as local buckling and distortional buckling.It highlighted how section shape,type of connection,and concrete infill all play amajor role in improving the strength of built-up CFS columns.
基金funded by National Key R&D Program of China(No.2022YFC3803500).
文摘In order to study the axial compression characteristics of brick masonry historical buildings, and to better protect and repair traditional mortar-brick masonry historical buildings, axial compression tests were carried out on three kinds of restored mortar (pure mud mortar, pure mortar, and mud mortar) brick masonry with restored mortar brick masonry as the object of study. The damage modes, axial compression chemical indexes (compressive strength and elastic modulus), load-displacement curves and stress-strain curves of the three kinds of restored mortar brick masonry were obtained. The experimental results show that the compressive strength of mud mortar brick masonry of 1.676 MPa is better than that of pure mud 1.530 MPa and pure mortar 1.471 MPa brick masonry, which is due to the difference in the bond effect between the restored mortar material and the brick block. According to the test results, the compressive strength formula of the restored mortar brick masonry was modified, and the reasons for the difference between the experimental value of the modulus of elasticity of the restored mortar brick masonry and that of the traditional formula and the measured value were compared and analyzed by a factor of 6.73–7.1. Referring to the axial-pressure ontological relationship of the conventional brick masonry, the 4-parameter segmental function expression was proposed for the characterization of the stress-strain relationship of the restored mortar brick masonry with the use of the stress-strain normalization process. The research results provide theoretical support for the inheritance and development of traditional mortar brick masonry historical architecture.
基金National Natural Science Foundation of China (59975076, 50175092)National Science Fund of China for Distinguished Young Scholars (50225518)
文摘Tube thinning control without wrinkling occurring is a key problem urgently to be solved for improving the forming qualities in numerical control （NC） bending processes of large-diameter Al-alloy thin-walled tubes （AATTs）. It may be a way solving this problem to exert axial compression loads （ACL） on the tube end in the bending. Thus, this article establishes a three-dimensional （3D） elastic-plastic explicit finite element （FE） model for the bending under ACL and has its reliability verified. Through a multi-index orthogonal experiment design, a combination of process parameters, each expressed by a proper range, for this FE model is derived to overcome the compression instability on tube ends. By combining the FE model with a wrinkling energy prediction model, an in-depth study is conducted on the forming characteristics of large-diameter AATTs with small bending radii and it can be concluded that （1） The larger the tube diameters and the smaller the bending radii, the larger the induced tangent tension stress zones on tube intrados, by which the tube maximum tangent compression stress zones will be partitioned in the bending processes; thus, the smaller the ACL roles in decreasing thinning degrees and the larger the compression instability possibilities on tube ends. （2） The tube wrinkling possibilities under ACL are larger than without ACL acting in the earlier forming periods, and smaller in the later ones. （3） For the tubes with a size factor less than 80, the ACL roles in decreasing thinning degrees are stronger than in increasing wrinkling possibilities.
基金National Natural Science Foundation of China under Grant Nos.52478488 and 51908013the National Key Basic Research and Development Program of China under Grant No.2018YFC1504305。
文摘To enhance the deformation capacity of vertical support columns of underground structures and improve their overall seismic performance,a new truncated column connected by unbonded prestressed tendons is proposed,inspired by the concepts of the toughness seismic resistance and rocking design.Although many experimental and numerical studies have focused on underground structures,research on the behavior of truncated columns remains limited.This paper develops threedimensional(3D)finite element(FE)models for various columns,including cast-in-place column(CIPC)and prestressed tendon truncated column(PTTC),to evaluate the effects of three parameters,including axial compression ratio(ACR),initial tendon stress,and the effect of hole diameter on mechanical performance—specifically deformation capacity,strength,residual deformation and gap width.The results indicate that the deformability and self-centering ability of the prestressed tendon truncated column is obviously superior to the cast-in-place column,but its strength was comparatively lower.The axial compression ratio has obvious effects on seismic performance,especially deformation and residual deformation,while initial tendon stress and hole diameter influence performance only in the case of a small axial compression ratio.This study systematically identifies the influence of various factors on seismic performance.Additionally,this study proposes a method to evaluate the self-centering capability of structures and establishes an empirical relationship between maximum recoverable deformation and the axial compression ratio.The developed numerical model can serve as a tool for future studies to predict the seismic responses of overall subway stations that feature truncated columns.
文摘This paper provides a review of recent research advances and trends in the area of stability of unstiffened circular cylindrical shells subjected to general non-uniform axial compressive stresses.Only the more important and interesting aspects of the research,judged from a personal viewpoint,are discussed.They can be crudely classified into four categories:(1) shells subjected to non-uniform loads;(2) shells on discrete supports;(3) shells with intended cutouts/holes;and (4) shells with non-uniform settlements.
基金The National Key Research and Development Program of China(No.2016YFC0701703)the Natural Science Foundation of Higher Education Institutions of Jiangsu Province(No.2016TM045J)the Scientific Innovation Research of Graduate Students in Jiangsu Province(No.KYLX_0151)
文摘The axial bearing capacity of prefabricated composite walls composed of inner and outer concrete wythes,expandable polystyrene(EPS)boards and steel sleeve connectors is investigated.An experimental study on the axial bearing capacity of four prefabricated composite walls after fire treatment is carried out.Two of the prefabricated composite walls are normal-temperature specimens,and the others are treated with fire.The damage modes and crack development are observed,and the axial bearing capacity,lateral deformation of the specimens,and the concrete and reinforcing bar strain are tested.The results show that the ultimate bearing capacity of specimens after a fire is less than that of normal-temperature specimens;when the insulation board thicknesses are 40 mm and 60 mm,the decrease amplitudes are 20.8%and 16.8%,respectively.The maximum lateral deformation of specimens after a fire is greater than that of normal-temperature specimens,and under the same level of load,the lateral deformation increases as the insulation board thickness increases.Moreover,the strain values of the concrete and reinforcing bars of specimens after a fire are greater than those of normal-temperature specimens,and the strain values increase as the thickness of insulation board increases.
