An efficient design-for-testability （DFT） technique is proposed to achieve low overhead for scan-based delay fault testing. Existing techniques for delay test such as skewed-load or broadside make the test generatio...An efficient design-for-testability （DFT） technique is proposed to achieve low overhead for scan-based delay fault testing. Existing techniques for delay test such as skewed-load or broadside make the test generation process complex and produce lower coverage for scan-based designs as compared with non-scan designs, whereas techniques such as enhanced-scan test can make the test easy but need an extra holding latch to add substantial hardware overhead. A new tri-state holding logic is presented to replace the common holding latch in enhanced-scan test to get a substantial low hardware overhead. This scheme can achieve low delay overhead by avoiding the holding latch on the critical timing scan path. What＇s more, this method can also keep the state and signal activity in the combinational circuit from the scan during data scan-in operation to reduce the power dissipation. Experiment results on a set of ISCAS89 benchmarks show the efficiency of the proposed scheme.展开更多
To study the diagnostic problem of Wire-OR （W-O） interconnect fault of PCB （Printed Circuit Board）, five modified boundary scan adaptive algorithms for interconnect test are put forward. These algorithms apply Glo...To study the diagnostic problem of Wire-OR （W-O） interconnect fault of PCB （Printed Circuit Board）, five modified boundary scan adaptive algorithms for interconnect test are put forward. These algorithms apply Global-diagnosis sequence algorithm to replace the equal weight algorithm of primary test, and the test time is shortened without changing the fault diagnostic capability. The descriptions of five modified adaptive test algorithms are presented, and the capability comparison between the modified algorithm and the original algorithm is made to prove the validity of these algorithms.展开更多
A new nondestructive test method-Impact Echo Scanning was introduced. Application of this method on pavement structure test was discussed. A method to increase the measurement accuracy of the test on multi-layers was ...A new nondestructive test method-Impact Echo Scanning was introduced. Application of this method on pavement structure test was discussed. A method to increase the measurement accuracy of the test on multi-layers was proposed, and was verified by field test. The test results show that the basic structural information can obtained rapidly and accurately by 3-D scanning of the impact echo system.展开更多
A two stage scan architecture is proposed to do low power and low test application cost scan testing. The first stage includes multiple scan chains, where each scan chain is driven by a primary input. Each scan flip-f...A two stage scan architecture is proposed to do low power and low test application cost scan testing. The first stage includes multiple scan chains, where each scan chain is driven by a primary input. Each scan flip-flop in the multiple scan chains drives a group of scan flip-flops. The scan flip-flop in the multiple scan chain and the scan flip-flop driven by it are assigned the same values for all test vectors. Scan flip-flops in the multiple scan chains and those in the second stage use separate clock signals, but the design for testability technqiue needs only one clock. The proposed scan architecture localizes test power consumption to the multiple scan chains during test application. Test signals assigned to scan flip-fiops in the multiple scan chains are applied to the scan flip-flops in the second stage after the test vector has been applied to the multiple scan chains. This technique can make test power consumption very small.展开更多
The IEEE Standard 1149.1 boundary scan (BS) implementation provides the internal access required for testing the digital printed circuit board (PCB). However, the integrity of the boundary scan test infrastructure sh...The IEEE Standard 1149.1 boundary scan (BS) implementation provides the internal access required for testing the digital printed circuit board (PCB). However, the integrity of the boundary scan test infrastructure should be tested first to guarantee the validation of the results of the rest functional test and diagnosis. This paper describes the fault models and test principles of the BS test access port (TAP) lines on PCBs. A test algorithm with high fault coverage and short time is then presented for the PCB on which all ICs are BS ones.展开更多
The study of wind erosion processes is of great importance to the prevention and control of soil wind erosion.In this study,three structurally intact soil samples were collected from the steppe of Inner Mongolia Auton...The study of wind erosion processes is of great importance to the prevention and control of soil wind erosion.In this study,three structurally intact soil samples were collected from the steppe of Inner Mongolia Autonomous Region,China and placed in a wind tunnel where they were subjected to six different wind speeds(10,15,17,20,25,and 30 m/s)to simulate wind erosion in the wind tunnel.After each test,the soil surfaces were scanned by a 3D laser scanner to create a high-resolution Digital Elevation Model(DEM),and the changes in wind erosion mass and microtopography were quantified.Based on this,we performed further analysis of wind erosion-controlling factors.The study results showed that the average measurement error between the 3D laser scanning method and weighing method was 6.23%for the three undisturbed soil samples.With increasing wind speed,the microtopography on the undisturbed soil surface first became smooth,and then fine stripes and pits gradually developed.In the initial stage of wind erosion processes,the ability of the soil to resist wind erosion was mainly affected by the soil hardness.In the late stage of wind erosion processes,the degree of soil erosion was mainly affected by soil organic matter and CaCO_(3)content.The results of this study are expected to provide a theoretical basis for soil wind erosion control and promote the application of 3D laser scanners in wind erosion monitoring.展开更多
Side channel attack may result in user key leakage as scan test techniques are applied for crypto-graphic chips. Many secure scan designs have been proposed to protect the user key. This paper meticulously selects thr...Side channel attack may result in user key leakage as scan test techniques are applied for crypto-graphic chips. Many secure scan designs have been proposed to protect the user key. This paper meticulously selects three current scan test techniques, analyses their advantages and disadvantages and also compares them in security and area overhead. Users can choose one of them according to the requirements and further combination can be implemented to achieve better performance.展开更多
In this paper, ultrasonic C-scan test of spot welds for stainless steel has been studied. It is concluded that large scanning step length contributes to high testing efficiency, however, the low-resolution C-scan imag...In this paper, ultrasonic C-scan test of spot welds for stainless steel has been studied. It is concluded that large scanning step length contributes to high testing efficiency, however, the low-resolution C-scan image generated cannot be used to assess spot welding quality reliably. Based on bicubic image interpolation, the C-scan image in low resolution with the large step length 1 000 ~xm is subdivided and reconstructed. By this means, the C-scan image resolution is greatly enhanced and testing results obtained are satisfactory, realizing rapid assessment of spot welds. The results of rapid ultrasonic C-scan test fit the actual metallographic measured value well. Mean value of normal distribution of error statistics is O. 006 67, and the standard deviation is O. 087 11. Rapid ultrasonic C-scan test based on image interpolation is of high accuracy and excellent stability.展开更多
Background: Detection of malignant liver mass is very important for the treatment modalities. Objective: The purpose of the present study was to establish the usefulness of CT scan in the diagnosis of malignant hepati...Background: Detection of malignant liver mass is very important for the treatment modalities. Objective: The purpose of the present study was to establish the usefulness of CT scan in the diagnosis of malignant hepatic mass. Methodology: This cross sectional study was carried out in the Department of Radiology and Imaging at Mymensingh Medical College Hospital (MMCH), Mymensingh, Banghabandhu Sheikh Mujib Medical University (B中央人民政府), Dhaka and Dhaka Medical College Hospital (DMCH), Dhaka during the period of 1st January 2006 to 31st December 2007. Patients admitted in the Department of Medicine and Department of Hepatobiliary of MMCH, B中央人民政府, and DMCH with the clinical diagnosis of fever, abdominal pain, anorexia, nausea/vomiting, loss of appetite, jaundice, weight loss and ascites were selected as study population. CT scan and histopathology were performed to all the patients. Result: A total number of 50 patients were recruited for this study. Mean age of all patients was 51.28 ± 14 years with a range of 17 year to 78 years. Among all patients 28 had multiple lesion, of them 71.4% was malignant and 28.6% was benign. On the other side 22 patients had solitary lesion, of them 36.4% was malignant and 63.6% was benign展开更多
The study of rock failure mechanisms is fundamental to geotechnical engineering,as it enhances design quality and mitigates disaster risks.This research employed in situ compression tests on 3D-printed rocklike sample...The study of rock failure mechanisms is fundamental to geotechnical engineering,as it enhances design quality and mitigates disaster risks.This research employed in situ compression tests on 3D-printed rocklike samples with a single flaw,combining Micro-CT scans and a specialized loading device to analyze their behavior.Mechanical properties and failure modes of these printed samples were compared to those of natural flawed sandstones,demonstrating the capability of 3D printing to replicate natural rock characteristics.By reconstructing 3D crack evolution from 2D CT images and applying digital volume correlation(DVC),the study visualized internal strain fields and established a relationship between strain patterns and rock failure.The results reveal that crack initiation consistently occurs at the flaw,advancing into tensile and secondary shear or mixed cracks.For flaw angles(α)ranging from 0°to 45°,the 3D-printed samples exhibited a higher number of newly formed cracks and a faster increase in crack volume with strain.In contrast,for flaw angles of 45°≤α≤90°,the opposite trend was observed.The internal strain field exhibited significant strain localization,with this uneven distribution playing a critical role in sample failure.When the flaw angle was in the range of 0°≤α≤30°,failure was primarily driven by tensile cracks,forming distinct tensile bands.Conversely,for 30°<α≤90°,a combination of tensile and shear cracks dominated the failure,producing both shear and tensile bands in the sample.Additionally,the strain field component ε_(yy) showed a strong correlation with the evolution of internal damage,providing valuable insights into the underlying rock failure mechanisms.展开更多
It is very important to detect transition-delay faults and stuck-at faults in system on chip （SoC） under 90 nm processing technology, and the transition-delay faults can only be detected by using an at-speed testing...It is very important to detect transition-delay faults and stuck-at faults in system on chip （SoC） under 90 nm processing technology, and the transition-delay faults can only be detected by using an at-speed testing method. In this paper, an on-chip clock （OCC） controller with a bypass function based on an internal phase-locked loop is designed to test faults in SoC. Furthermore, a clock chain logic which can eliminate the metastable state is realized to generate an enable signal for the OCC controller, and then, the test pattern is generated by automatic test pattern generation （ATPG） tools. Next, the scan test pattern is simulated by using the Synopsys tool and the correctness of the design is verified. The result shows that the design of an at-speed scan test in this paper is highly efficient for detecting timing-related defects. Finally, the 89.29% transition-delay fault coverage and the 94.50% stuck-at fault coverage are achieved, and it is successfully applied to an integrated circuit design.展开更多
The mechanical properties of the SiC fiber-reinforced Mg-Al metal matrix composite materials have been studied on internal microstructure by (scanning electron microscopy) SEM in-situ tensile test. The emergence and p...The mechanical properties of the SiC fiber-reinforced Mg-Al metal matrix composite materials have been studied on internal microstructure by (scanning electron microscopy) SEM in-situ tensile test. The emergence and propagation of the crack, and the fracture behavior in materials have been observed and studied. It is found that in the case of the tensile test, the crack emerged in SiC fiber initially. In the case of the strong cohesion of the fiber-metal interface, the crack propagated in the fiber, meanwhile the fibers in the neighborhood of the cracked fiber began to crack and the Mg-Al metal deformed plastically, and at last the material fractured. Otherwise the toughness of the materials grows in the case of the lower cohesion of the fiber-metal matrix interface.展开更多
基金This project was supported by the National Natural Science Foundation of China (90407007).
文摘An efficient design-for-testability （DFT） technique is proposed to achieve low overhead for scan-based delay fault testing. Existing techniques for delay test such as skewed-load or broadside make the test generation process complex and produce lower coverage for scan-based designs as compared with non-scan designs, whereas techniques such as enhanced-scan test can make the test easy but need an extra holding latch to add substantial hardware overhead. A new tri-state holding logic is presented to replace the common holding latch in enhanced-scan test to get a substantial low hardware overhead. This scheme can achieve low delay overhead by avoiding the holding latch on the critical timing scan path. What＇s more, this method can also keep the state and signal activity in the combinational circuit from the scan during data scan-in operation to reduce the power dissipation. Experiment results on a set of ISCAS89 benchmarks show the efficiency of the proposed scheme.
文摘To study the diagnostic problem of Wire-OR （W-O） interconnect fault of PCB （Printed Circuit Board）, five modified boundary scan adaptive algorithms for interconnect test are put forward. These algorithms apply Global-diagnosis sequence algorithm to replace the equal weight algorithm of primary test, and the test time is shortened without changing the fault diagnostic capability. The descriptions of five modified adaptive test algorithms are presented, and the capability comparison between the modified algorithm and the original algorithm is made to prove the validity of these algorithms.
基金Funded by the National Natural Science Foundation of China(No.50472042) Doctoral Base Fund of Ministry of Education of China(No.20050497010)
文摘A new nondestructive test method-Impact Echo Scanning was introduced. Application of this method on pavement structure test was discussed. A method to increase the measurement accuracy of the test on multi-layers was proposed, and was verified by field test. The test results show that the basic structural information can obtained rapidly and accurately by 3-D scanning of the impact echo system.
基金This workis supported in part by JSPS under grant L03540and the National Science Foundation of China under grant60373009
文摘A two stage scan architecture is proposed to do low power and low test application cost scan testing. The first stage includes multiple scan chains, where each scan chain is driven by a primary input. Each scan flip-flop in the multiple scan chains drives a group of scan flip-flops. The scan flip-flop in the multiple scan chain and the scan flip-flop driven by it are assigned the same values for all test vectors. Scan flip-flops in the multiple scan chains and those in the second stage use separate clock signals, but the design for testability technqiue needs only one clock. The proposed scan architecture localizes test power consumption to the multiple scan chains during test application. Test signals assigned to scan flip-fiops in the multiple scan chains are applied to the scan flip-flops in the second stage after the test vector has been applied to the multiple scan chains. This technique can make test power consumption very small.
文摘The IEEE Standard 1149.1 boundary scan (BS) implementation provides the internal access required for testing the digital printed circuit board (PCB). However, the integrity of the boundary scan test infrastructure should be tested first to guarantee the validation of the results of the rest functional test and diagnosis. This paper describes the fault models and test principles of the BS test access port (TAP) lines on PCBs. A test algorithm with high fault coverage and short time is then presented for the PCB on which all ICs are BS ones.
基金supported by National Natural Science Foundation of China(41871010)The Second Comprehensive Scientific Expedition to the Qinghai-Tibet Plateau of China(2019QZKK0906)。
文摘The study of wind erosion processes is of great importance to the prevention and control of soil wind erosion.In this study,three structurally intact soil samples were collected from the steppe of Inner Mongolia Autonomous Region,China and placed in a wind tunnel where they were subjected to six different wind speeds(10,15,17,20,25,and 30 m/s)to simulate wind erosion in the wind tunnel.After each test,the soil surfaces were scanned by a 3D laser scanner to create a high-resolution Digital Elevation Model(DEM),and the changes in wind erosion mass and microtopography were quantified.Based on this,we performed further analysis of wind erosion-controlling factors.The study results showed that the average measurement error between the 3D laser scanning method and weighing method was 6.23%for the three undisturbed soil samples.With increasing wind speed,the microtopography on the undisturbed soil surface first became smooth,and then fine stripes and pits gradually developed.In the initial stage of wind erosion processes,the ability of the soil to resist wind erosion was mainly affected by the soil hardness.In the late stage of wind erosion processes,the degree of soil erosion was mainly affected by soil organic matter and CaCO_(3)content.The results of this study are expected to provide a theoretical basis for soil wind erosion control and promote the application of 3D laser scanners in wind erosion monitoring.
文摘Side channel attack may result in user key leakage as scan test techniques are applied for crypto-graphic chips. Many secure scan designs have been proposed to protect the user key. This paper meticulously selects three current scan test techniques, analyses their advantages and disadvantages and also compares them in security and area overhead. Users can choose one of them according to the requirements and further combination can be implemented to achieve better performance.
文摘In this paper, ultrasonic C-scan test of spot welds for stainless steel has been studied. It is concluded that large scanning step length contributes to high testing efficiency, however, the low-resolution C-scan image generated cannot be used to assess spot welding quality reliably. Based on bicubic image interpolation, the C-scan image in low resolution with the large step length 1 000 ~xm is subdivided and reconstructed. By this means, the C-scan image resolution is greatly enhanced and testing results obtained are satisfactory, realizing rapid assessment of spot welds. The results of rapid ultrasonic C-scan test fit the actual metallographic measured value well. Mean value of normal distribution of error statistics is O. 006 67, and the standard deviation is O. 087 11. Rapid ultrasonic C-scan test based on image interpolation is of high accuracy and excellent stability.
文摘Background: Detection of malignant liver mass is very important for the treatment modalities. Objective: The purpose of the present study was to establish the usefulness of CT scan in the diagnosis of malignant hepatic mass. Methodology: This cross sectional study was carried out in the Department of Radiology and Imaging at Mymensingh Medical College Hospital (MMCH), Mymensingh, Banghabandhu Sheikh Mujib Medical University (B中央人民政府), Dhaka and Dhaka Medical College Hospital (DMCH), Dhaka during the period of 1st January 2006 to 31st December 2007. Patients admitted in the Department of Medicine and Department of Hepatobiliary of MMCH, B中央人民政府, and DMCH with the clinical diagnosis of fever, abdominal pain, anorexia, nausea/vomiting, loss of appetite, jaundice, weight loss and ascites were selected as study population. CT scan and histopathology were performed to all the patients. Result: A total number of 50 patients were recruited for this study. Mean age of all patients was 51.28 ± 14 years with a range of 17 year to 78 years. Among all patients 28 had multiple lesion, of them 71.4% was malignant and 28.6% was benign. On the other side 22 patients had solitary lesion, of them 36.4% was malignant and 63.6% was benign
基金supported by the Korea Institute of Energy Technology Evaluation and Planning(KETEP)grant funded by the Korea Government(MOTIE)(Grant No.20214000000500,Training program of CCUS for the green growth)by the National Research Foundation of Korea(NRF)grant funded by the Korea Government(MSIT)(Grant No.2022R1F1A1076409)the support from the Chinese Scholarship Council for awarding a scholarship(CSC No.202106820011).
文摘The study of rock failure mechanisms is fundamental to geotechnical engineering,as it enhances design quality and mitigates disaster risks.This research employed in situ compression tests on 3D-printed rocklike samples with a single flaw,combining Micro-CT scans and a specialized loading device to analyze their behavior.Mechanical properties and failure modes of these printed samples were compared to those of natural flawed sandstones,demonstrating the capability of 3D printing to replicate natural rock characteristics.By reconstructing 3D crack evolution from 2D CT images and applying digital volume correlation(DVC),the study visualized internal strain fields and established a relationship between strain patterns and rock failure.The results reveal that crack initiation consistently occurs at the flaw,advancing into tensile and secondary shear or mixed cracks.For flaw angles(α)ranging from 0°to 45°,the 3D-printed samples exhibited a higher number of newly formed cracks and a faster increase in crack volume with strain.In contrast,for flaw angles of 45°≤α≤90°,the opposite trend was observed.The internal strain field exhibited significant strain localization,with this uneven distribution playing a critical role in sample failure.When the flaw angle was in the range of 0°≤α≤30°,failure was primarily driven by tensile cracks,forming distinct tensile bands.Conversely,for 30°<α≤90°,a combination of tensile and shear cracks dominated the failure,producing both shear and tensile bands in the sample.Additionally,the strain field component ε_(yy) showed a strong correlation with the evolution of internal damage,providing valuable insights into the underlying rock failure mechanisms.
基金Project supported by the Key Project Science and Technology Cooperation of Fujian Province,China(No.2013I0003)
文摘It is very important to detect transition-delay faults and stuck-at faults in system on chip （SoC） under 90 nm processing technology, and the transition-delay faults can only be detected by using an at-speed testing method. In this paper, an on-chip clock （OCC） controller with a bypass function based on an internal phase-locked loop is designed to test faults in SoC. Furthermore, a clock chain logic which can eliminate the metastable state is realized to generate an enable signal for the OCC controller, and then, the test pattern is generated by automatic test pattern generation （ATPG） tools. Next, the scan test pattern is simulated by using the Synopsys tool and the correctness of the design is verified. The result shows that the design of an at-speed scan test in this paper is highly efficient for detecting timing-related defects. Finally, the 89.29% transition-delay fault coverage and the 94.50% stuck-at fault coverage are achieved, and it is successfully applied to an integrated circuit design.
文摘The mechanical properties of the SiC fiber-reinforced Mg-Al metal matrix composite materials have been studied on internal microstructure by (scanning electron microscopy) SEM in-situ tensile test. The emergence and propagation of the crack, and the fracture behavior in materials have been observed and studied. It is found that in the case of the tensile test, the crack emerged in SiC fiber initially. In the case of the strong cohesion of the fiber-metal interface, the crack propagated in the fiber, meanwhile the fibers in the neighborhood of the cracked fiber began to crack and the Mg-Al metal deformed plastically, and at last the material fractured. Otherwise the toughness of the materials grows in the case of the lower cohesion of the fiber-metal matrix interface.
