The new CL-20(hexanitrohexaazaisowurtzitane)type aluminized explosives in the overdrive detonation(ODD)conditions of the core problem is how to accurately represent the state of the overdrive detonation products.To th...The new CL-20(hexanitrohexaazaisowurtzitane)type aluminized explosives in the overdrive detonation(ODD)conditions of the core problem is how to accurately represent the state of the overdrive detonation products.To this end,this paper is based on the impedance matching method to test the ODD conditions of CL-20 type aluminium explosive particle velocity.Calculated the interfacial pressure of the shock wave in different media.Determined the characteristic parameters of the reaction zone of the detonation of CL-20 aluminized explosives.Calibrated the parameters of the JoneseWilkinseLee(JWL)+γ equation for the detonation products(DPs).Revealed the effect of different DPs equation of state(EOS)on the Hugoniot pressure of ODD.The results indicate that when the content of aluminum powder ranges from 0%to 30%,the duration of the ODD reaction zone and the width of the detonation reaction zone of the CL-20-based aluminized explosive are directly proportional to the content of aluminum powder.The width of the detonation reaction zone is increased by 1.97 times to 2.7 times compared to that of the reaction zone without the addition of aluminum powder.However,the energy release efficiency of the detonation reaction zone is inversely proportional to the content of aluminum powder.When the aluminum powder content was held constant,the incorporation of AP caused a 25%reduction in the energy release efficiency of the detonation reaction zone.Compared with existing ODD state equations,the JWL +γ equation is superior in calibrating overpressure Hugoniot data and the isentropic expansion in the C-J state.The deviation between calculated pressure results and experimental measurements is within 6%.展开更多
Afterburning behind the detonation front of an aluminized explosive releases energy on the millisecond timescale,which prolong the release of detonation energy and the energy release at different stages also shows sig...Afterburning behind the detonation front of an aluminized explosive releases energy on the millisecond timescale,which prolong the release of detonation energy and the energy release at different stages also shows significant differences.However,at present,there are few effective methods for evaluating the energy release characteristics of the middle reaction stage of such explosives,which can have a duration of tens to hundreds of microseconds.The present work demonstrates an approach to assessing the midstage of an aluminized explosive detonation based on a water push test employing a high degree of confinement.In this method,the explosive is contained in a steel cylinder having one end closed that is installed at the bottom of a transparent water tank.Upon detonation,the gaseous products expand in one direction while forcing water ahead of them.The resulting underwater shock wave and the interface between the gas phase products and the water are tracked using an ultra-high-speed framing and streak camera.The shock wave velocity in water and the expansion work performed by the gaseous detonation products were calculated to assess the energy release characteristics of aluminized explosives such as CL-20 and RDX in the middle stage of the detonation reaction.During the middle stage of the detonation process of these aluminized explosives,the aluminum reaction reduced the attenuation of shock waves and increased the work performed by gas phase products.A higher aluminum content increased the energy output while the presence of oxidants slowed the energy release rate.This work demonstrates an effective means of evaluating the performance of aluminized explosives.展开更多
Taking CL-20(Hexanitrohexaazaisowurtzitane)-based aluminized explosives with high gurney energy as the research object, this research experimentally investigates the work capability of different aluminized explosive f...Taking CL-20(Hexanitrohexaazaisowurtzitane)-based aluminized explosives with high gurney energy as the research object, this research experimentally investigates the work capability of different aluminized explosive formulations when driving metal flyer plates in the denotation wave propagation direction.The research results showed that the formulations with 43 μm aluminum(Al) powder particles(The particle sizes of Al powder were in the range of 2~43 μm) exhibited the optimal performance in driving flyer plates along the denotation wave propagation direction. Compared to the formulations with Al powder 13 μm, the formulations with Al powder 2 μm delivered better performance in accelerating metal flyer plates in the early stage, which, however, turned to be poor in the later stage. The CL-20-based explosives containing 25% Al far under-performed those containing 15% Al. Based on the proposed quasi-isentropic hypothesis, relevant isentropy theories, and the functional relationship between detonation parameters and entropy as well as Al reaction degree, the characteristic lines of aluminized explosives in accelerating flyer plates were theoretically studied, a quasi-isentropic theoretical model for the aluminized explosive driving the flyer plate was built and the calculation methods for the variations of flyer plate velocity, Al reaction degree, and detonation product parameters with time and axial positions were developed. The theoretical model built is verified by the experimental results of the CL-20-based aluminized explosive driving flyer plate. It was found that the model built could accurately calculate the variations of flyer plate velocity and Al reaction degree over time. In addition, how physical parameters including detonation product pressure and temperature varied with time and axial positions was identified. The action time of the positive pressure after the detonation of aluminized explosives was found prolonged and the downtrend of the temperature was slowed down and even reversed to a slight rise due to the aftereffect reaction between the Al powder and the detonation products.展开更多
The outermost coating with single phase Ni2Al3 was obtained on copper surface by electrodepositing nickel followed by slurry pack aluminizing at 800 °C for 12 h. The oxidation resistance and microstructure of the...The outermost coating with single phase Ni2Al3 was obtained on copper surface by electrodepositing nickel followed by slurry pack aluminizing at 800 °C for 12 h. The oxidation resistance and microstructure of the coating oxidized in ambient air at 1000 °C for 25-250 h were investigated using SEM, X-ray diffraction and optical microscope methods. The results show that the copper with single phase Ni2Al3 coating possesses the best high temperature oxidation resistance, and the mass gain of the coating is 1/15 that of pure copper and 1/2 that of nickel coating, respectively. The specimen surface after being oxidized for 25 h still comprises Ni2Al3 phase. However, when the time of oxidizing treatment increases to 50 h, the Ni Al phase is formed. It is also found that the Ni2Al3 phase completely turns into Ni Al phase after oxidizing treatment for 100 h and above. The Ni Al coating shows excellent high temperature oxidation resistance when oxidation time is 250 h.展开更多
Pressure histories were tested in a 500-L chamber to identify the pressure load in confined explosion from aluminized explosives. Different aluminized explosives with Al/O, ranging from 0.25 to 1.23, were used. The re...Pressure histories were tested in a 500-L chamber to identify the pressure load in confined explosion from aluminized explosives. Different aluminized explosives with Al/O, ranging from 0.25 to 1.23, were used. The recorded pressure curves could express the reflection of initial shock wave and the after burning combustion of aluminum. As there is no objective way to gain quasi-static pressure(P_(QS)),method of multipoint averaging was used in smoothing the original pressure curves to gain the P_(QS). The P_(QS),rising time of pressure(t_(QS)) which stands for the duration of the initial reflected shock wave, and attenuation coefficient(ω) which stands for the supportive effects of the combustion of aluminum to the P_(QS) are used to characterize the pressure load in the confined explosion from aluminized explosives. The research results showed that the Al/O significantly affected the three characteristic quantities. With the increase of Al/O, the P_(QS) increased at first and decreased later, gaining maximum at Al/O=0.99; the t_(QS)sustained growth and the ω decreased at first and increased later, gaining minimum at AI/O=0.99.展开更多
The effects of the addition of rare earth （RE） elements on the void band in the diffusion layer, and the re sistances to both oxidation and spalling of aluminized steel were investigated through high temperature oxi...The effects of the addition of rare earth （RE） elements on the void band in the diffusion layer, and the re sistances to both oxidation and spalling of aluminized steel were investigated through high temperature oxidation and spalling tests. The results showed that RE had significant effects on the void band in the diffusion layer and the properties of aluminized steel. After diffusion treatment, a considerable number of the voids between the middle layer and transitional layer of pure aluminized coating, aggregated into wavy-line-shaped void bands parallel to the outer surface. For the RE added aluminized coating, only a few voids aggregated into intermittent block shapes. During high temperature oxidation at 800 ℃ for 200 h, the wavy void band of pure aluminized coating aggregated further into a linear crack parallel to the outer surface, and the internal oxidation occurred within them; the open cracks perpendicular to the surface penetrated through the diffusion layer. For the RE added aluminized coating, only a few voids aggregated into intermittent meniscus shapes. During cyclic spalling tests, the peeling, spallation, and pulver ulent cracking occurred along the void band in the diffusion layer of pure aluminized coating, but only a little spallation occurred in the diffusion layer of the RE-added aluminized coating, in which cracks perpendicular to the surface were much smaller than those of pure aluminized coating and did not penetrate through the diffusion layer. It is evident that RE addition can restrain the formation and aggregation of voids and subsequently improve the resistances to oxidation and spalling. The mechanism of the RE effect on the void band in the diffusion layer is also discussed.展开更多
This work aims to research the effects on the early responses of the air-backed plate subjected to the loading generated by the underwater explosion with aluminized explosives.The loading characteristics of underwater...This work aims to research the effects on the early responses of the air-backed plate subjected to the loading generated by the underwater explosion with aluminized explosives.The loading characteristics of underwater explosion for ideal explosive(TNT),aluminized explosives(RS211 and RBUL) are obtained experimentally.The tested aluminized explosives have different energy output compared with TNT.Based on the Taylor plate theory,the early responses of the air-backed steel plate affected by the measured loading is analyzed.The analytical results indicate that the pressure curve of the shock wave within 1 time decay constant is the main factor affecting the kick-off velocity of the plate when cavitation occurring.The velocity responses of the plate produced by the loading of RS211 and RBUL are obviously different with that of an equivalent TNT charge,which also indicates validity and suitability should be noticed in the case of substituting TNT for aluminized explosives.Moreover,the uncertainties in the responses of the plate produced by RS211 and RBUL are much larger than TNT.展开更多
To investigate the shock wave characteristics of RDX-based aluminized explosives,air blast tests were conducted for measuring the parameters of 10 kg aluminized explosives which contained 0-40% aluminum.The results sh...To investigate the shock wave characteristics of RDX-based aluminized explosives,air blast tests were conducted for measuring the parameters of 10 kg aluminized explosives which contained 0-40% aluminum.The results showed that with the increasing of aluminum content,the overpressures and impulses increase at first and then decrease within 7 m or 5 m,which reached the maximum when aluminum content was 20% or 30%.Power exponential formulas are used to fit the shock wave parameters vs scaled distance,where an equal weight of TNT is used to calculate the scaled distance.The overpressures of HL0 and TNT in tested locations not only conform to the similar law,but also conform to the same attenuation law after gaining the scaled distances of equal TNT mass.The pre-exponential factors of overpressure and impulse,kp and kI,decrease along with the increasing of Al content and keep the same pace as the calculated PCJ）.The attenuation coefficients a_P and aIincrease at first and decrease later with the increasing of aluminum content,and they reached the maximal values with30% Al containing,which keeps the same pace as the calculated QV.展开更多
Cis-and trans-1,3,4,6-tetranitroglycouril(TNGU, Sorguyl) have been considered for density functional treatment at the levels of B3LYP/6-31 G(d,p) and B3LYP/cc-PVDZ. Cis-TNGU has been found to be more stable than its t...Cis-and trans-1,3,4,6-tetranitroglycouril(TNGU, Sorguyl) have been considered for density functional treatment at the levels of B3LYP/6-31 G(d,p) and B3LYP/cc-PVDZ. Cis-TNGU has been found to be more stable than its trans isomer. Then, mono and dialuminized(cis-TNGU + Al and cis-TNGU+2Al) have been subjected to theoretical treatment at the level of B3LYP/6-31 + G(d). The spin states of the aluminized cis-TNGU composites have been considered as well. Although, cis-TNGU + Al(doublet) is found to be structurally stable, cis-TNGU+2Al singlet and triplet composites undergo certain bond cleavages.Structural and some quantum chemical properties, IR-UV spectra etc. have been presented.展开更多
A quasi-isentropic study on the process of driving a cylinder with aluminized explosives was carried out to examine the influence of the aluminum(Al) reaction rate on cylinder expansion and the physical parameters of ...A quasi-isentropic study on the process of driving a cylinder with aluminized explosives was carried out to examine the influence of the aluminum(Al) reaction rate on cylinder expansion and the physical parameters of the detonation products. Based on the proposed quasi-isentropic hypothesis and relevant isentropic theories, the characteristic lines of aluminized explosives driving a cylinder were analyzed,and a quasi-isentropic model was established. This model includes the variation of the cylinder wall velocity and the physical parameters of the detonation products with the Al reaction degree. Using previously reported experimental results, the quasi-isentropic model was verified to be applicative and accurate. This model was used to calculate the physical parameters for cylinder experiments with aluminized cyclotrimethylenetrinitramine explosives with 15.0 % and 30.0 % Al content. The results show that this quasi-isentropic model can be used not only to calculate the cylinder expansion rule or Al reaction degree, but also to calculate the physical parameters of the detonation products in the process of cylinder expansion. For explosives with 15.0 % and 30.0 % Al, 24.3 % and 18.5 % of the Al was found to have reacted at 33.9 μs and 34.0 μs, respectively. The difference in Al content results in different reaction intensity, occurrence time, and duration of two forms of reaction(diffusion and kinetic) between the Al powder and the detonation products;the post-detonation burning reaction between the Al powder and the detonation products prolongs the positive pressure action time, resulting in a continuous rise in temperature after detonation.展开更多
The time-dependent Jones Wilkins-Lee equation products for aluminized explosives. To obtain the of state （JWL-EOS） is applied to describe detonation state time-dependent JWL-EOS parameters, cylinder tests and underw...The time-dependent Jones Wilkins-Lee equation products for aluminized explosives. To obtain the of state （JWL-EOS） is applied to describe detonation state time-dependent JWL-EOS parameters, cylinder tests and underwater explosion experiments are performed. According to the result of the wall radial velocity in cylinder tests and the shock wave pressures in underwater explosion experiments, the time-dependent JWL-EOS parameters are determined by iterating these variables in AUTODYN hydroeode simulations until the experimental values are reproduced. In addition, to verify the reliability of the derived JWL-EOS parameters, the aluminized explosive experiment is conducted in concrete. The shock wave pressures in the affected concrete bodies are measured by using manganin pressure sensors, and the rod velocity is obtained by using a high-speed camera. Simultaneously, the shock wave pressure and the rod velocity are calculated by using the derived time-dependent JWL equation of state. The calculated results are in good agreement with the experimental data.展开更多
Hot-dip aluminizing（HDA） is a proven surface coating technique for improving the oxidation and corrosion resistance of ferrous substrates. Although extensive studies on the HDA of plain carbon steels have been repor...Hot-dip aluminizing（HDA） is a proven surface coating technique for improving the oxidation and corrosion resistance of ferrous substrates. Although extensive studies on the HDA of plain carbon steels have been reported, studies on the HDA of stainless steels are limited. Because of the technological importance of stainless steels in high-temperature applications, studies of their microstructural development during HDA are needed. In the present investigation, the HDA of AISI 321 stainless steel was carried out in a pure Al bath. The microstructural features of the coating were studied using scanning electron microscopy and transmission electron microscopy. These studies revealed that the coating consists of two regions： an Al top coat and an aluminide layer at the interface between the steel and Al. The Al top coat was found to consist of intermetallic phases such as Al_7Cr and Al_3Fe dispersed in an Al matrix. Twinning was observed in both the Al_7Cr and the Al_3Fe phases. Furthermore, the aluminide layer comprised a mixture of nanocrystalline Fe_2Al_5, Al_7Cr, and Al. Details of the microstructural features are presented, and their formation mechanisms are discussed.展开更多
Microstructures,high-temperature oxidation and wear resistance of hot dipping Al-Si-Y coating on SCH12 heat resistant cast steel were investigated in this study.The aluminized coating was characterized by scanning ele...Microstructures,high-temperature oxidation and wear resistance of hot dipping Al-Si-Y coating on SCH12 heat resistant cast steel were investigated in this study.The aluminized coating was characterized by scanning electron microscopy(SEM),energy dispersive X-ray spectrometry(EDX)and X-ray diffraction(XRD).The results showed that the coating was composed of the Al-rich outer layer and the intermetallics inner layer.In the Al-rich layer,some Y-rich precipitates and Fe-Al-Si-Cr precipitates could be observed.The intermetallics layer presented three layers induced by the increase of Fe,Cr,Ni content and the corresponding decrease of Al,Si content.The oxidation tests were conducted in still air at 850℃for up to 100 h.After oxidation,a top oxide scale composed of mainlyα-Al2O3,Al5Y3O12 was formed on the steel surface.The intermetallics beneath the oxide scale consisted of mainly FeAl and small amount of Fe2Al5 and Cr3Si phase.The mass gain of the coated and uncoated SCH1steel is 0.45 mg/cm 2 and 0.57 mg/cm 2,respectively.The wear resistance was investigated using a high-temperature pin-on-disc tribometer at 650℃.The wear rate for the coated and uncoated steel is 0.45μm 3 /μm.N and 3.01μm 3 /μm.N,respectively.The high temperature wear tests and oxidation tests results demonstrated that the yttrium-modified aluminized specimen had significantly improved high-temperature wear resistance and equivalent oxidation resistance compared with the original SCH12 specimen.展开更多
The corrosion behavior of Super304H,HR3C and related aluminized coatings under K_(2)SO_(4)+Na_(2)SO_(4)(mass ratio=1:1)and K_(2)SO_(4)+Na_(2)SO_(4)+KCl(45:45:10)deposits in a mixed gas of 0.5SO_(2)–4O_(2)–20H_(2)O-7...The corrosion behavior of Super304H,HR3C and related aluminized coatings under K_(2)SO_(4)+Na_(2)SO_(4)(mass ratio=1:1)and K_(2)SO_(4)+Na_(2)SO_(4)+KCl(45:45:10)deposits in a mixed gas of 0.5SO_(2)–4O_(2)–20H_(2)O-75.5CO_(2)(vol.%)at 700℃were studied.Super304H undergoes severe corrosion under both deposits,the addition of KCl did not significantly accelerate the corrosion process but resulted in an extremely porous and thickness-doubled scale.While HR3C with higher Cr content shows excellent corrosion resistance in Cl free environment due to the formation of dense Cr_(2)O_(3).Due to the involvement of Cl,HR3C can no longer resist the corrosion of the salts.The corrosion depth increases by two orders of magnitude and becomes as severe as Super304H.Aluminizing significantly improved the corrosion resistance of the alloys on account ofα-Al_(2)O_(3)formation by a new mechanism.The addition of KCl had little effect on this mechanism and only increased the thickness of the corrosion products slightly.展开更多
Aluminized coating was prepared on K452 superalloy by chemical vapor deposition(CVD)technique.The oxidation/corrosion behavior of alloy and coating were investigated at 750℃in air,air with solid NaCl deposit and mois...Aluminized coating was prepared on K452 superalloy by chemical vapor deposition(CVD)technique.The oxidation/corrosion behavior of alloy and coating were investigated at 750℃in air,air with solid NaCl deposit and moist air with solid NaCl deposit,respectively.The microstructure and composition of samples were characterized by SEM/EDS and XRD techniques.The results demonstrated that aluminized coating exhibited better oxidation/corrosion resistance than K452 alloy in the three environments above.And the main oxidation and corrosion products of alloy were Cr_(2)O_(3)and NiO,respectively.This indicated that Ni participated in the corrosion process due to the depletion of Cr during accelerated corrosion.Therefore,the established corrosion scale was non-protective,which could not protect underlying alloy from accelerated corrosion.Contrarily,the main oxidation and corrosion products of coating were protective Al_(2)O_(3),which acted as a barrier to separate coating from NaCl and oxygen,interrupting the self-sustainable accelerated corrosion.Additionally,the presence of water vapor was beneficial in reducing the spallation of corrosion products within a short time.The mechanisms of K452 alloy and aluminized coating in the three environments above were discussed in detail.展开更多
Dissolution kinetics of CaO·2Al_(2)O_(3)(CA_(2))particles in a synthetic CaO-Al_(2)O_(3)-SiO_(2)steelmaking slag system have been investigated using the high-temperature confocal laser scanning microscope.Effects...Dissolution kinetics of CaO·2Al_(2)O_(3)(CA_(2))particles in a synthetic CaO-Al_(2)O_(3)-SiO_(2)steelmaking slag system have been investigated using the high-temperature confocal laser scanning microscope.Effects of temperature(i.e.,1500,1550,and 1600℃)and slag composition on the dissolution time of CA_(2)particles are investigated,along with the time dependency of the projection area of the particle during the dissolution process.It is found that the dissolution rate was enhanced by either an increase in temperature or a decrease in slag viscosity.Moreover,a higher ratio of CaO/Al_(2)O_(3)(C/A)leads to an increased dissolution rate of CA_(2)particle at 1600℃.Thermodynamic calculations suggested the dissolution product,i.e.,melilite,formed on the surface of the CA_(2)particle during dissolution in slag with a C/A ratio of 3.8 at 1550℃.Scanning electron microscopy equipped with energy dispersive X-ray spectrometry analysis of as-quenched samples confirmed the dissolution path of CA_(2)particles in slags with C/A ratios of 1.8 and 3.8 as well as the melilite formed on the surface of CA_(2)particle.The formation of this layer during the dissolution process was identified as a hindrance,impeding the dissolution of CA_(2)particle.A valuable reference for designing or/and choosing the composition of top slag for clean steel production is provided,especially using calcium treatment during the secondary refining process.展开更多
The high-temperature oxidation resistance of AISI 321 stainless steel used in solar thermal power heat exchangers determines its service life.In this study,aluminizing and subsequent laser shock peening(LSP)treatments...The high-temperature oxidation resistance of AISI 321 stainless steel used in solar thermal power heat exchangers determines its service life.In this study,aluminizing and subsequent laser shock peening(LSP)treatments were employed to improve the high-temperature oxidation resistance of AISI 321 stainless steel at 620°C.These two treatments decreased the oxidation rate of AISI 321 steel.Specifically,the optimal oxidation resistance was observed in aluminized steel before oxidation for 144 h owing to the increased entropy of the LSP-treated specimen.After 144 h,LSP-treated steel achieved the best oxidation resistance because of the formation of a protectiveα-Al2O3film.Moreover,the large amount of subgrain boundaries formed on the aluminized layer of the LSP-treated samples could act as short-circuit paths for the outward diffusion of Al,facilitating the rapid nucleation ofα-Al2O3.Meanwhile,the aluminized layer could isolate the contact between the oxidation environment and matrix,thereby decreasing the oxidation rate.Furthermore,the minimum oxidation parabolic constant was calculated for LSP-treated steel(6.45787×10^(-14)),which was 69.18%and 36.36%that of aluminized and 321 steel,respectively,during the entire oxidation process.Therefore,the combination of aluminizing and LSP treatments can improve the high-temperature oxidation resistance of 321 stainless steel,providing a new idea for its surface treatment to achieve a long service life at high temperatures.展开更多
In order to prepare high density magnesium aluminate spinel materials,the light-burned magnesia and alumina powder were used as the main raw materials.Active magnesium aluminate spinel powders were synthesized at diff...In order to prepare high density magnesium aluminate spinel materials,the light-burned magnesia and alumina powder were used as the main raw materials.Active magnesium aluminate spinel powders were synthesized at different temperatures,and the sintering properties of the synthesized materials were characterized.The results show that the optimal light-burned temperature for synthesizing active magnesium aluminate spinel raw materials with small grain sizes and high sintering activity is 1400℃.The active spinel raw materials were sintered at 1750℃ for 3 h to form a dense spinel material,in which the spinel grains were well developed,exhibited a dense interlocking structure,and were uniformly distributed,with an average grain size of about 7.26μm.The bulk density and apparent porosity of the dense spinel material were 3.29 g·cm^(-3) and 3.5%,respectively.展开更多
We focused on the efflorescence induced microstructural evolution of ettringite-rich systems prepared with calcium aluminate cement(CAC)and anhydrite.The effects of anhydrite on the visible efflorescence,and the corre...We focused on the efflorescence induced microstructural evolution of ettringite-rich systems prepared with calcium aluminate cement(CAC)and anhydrite.The effects of anhydrite on the visible efflorescence,and the corresponding capillary absorption of CAC-anhydrite mortars were revealed.The composition and microstructure of efflorescence-causing substances were investigated by optical microscope,in-situ Raman spectroscopy,scanning electron microscope,energy dispersive spectrometer,thermogravimetric analysis,and differential scanning calorimetry,at multi-scales.Results indicate that,besides the calcium carbonate,ettringite is another main component of efflorescence-causing substances.Compared with the neat CAC mortars,the addition of anhydrite has a significant effect on the degree of efflorescence by acting on the composition of hydration products and pore structure.In addition,methods are proposed for the prevention of efflorescence of CAC-anhydrite binary system.展开更多
In order to investigate the modification behavior and regularity of inclusions in X80 pipeline steel by Mg-treatment, the comparative industrial experiments of Mg-treatment and Ca-treatment in X80 pipeline steel were ...In order to investigate the modification behavior and regularity of inclusions in X80 pipeline steel by Mg-treatment, the comparative industrial experiments of Mg-treatment and Ca-treatment in X80 pipeline steel were carried out. Mg and Ca were added to the steel in the form of cored wire after RH (Ruhrstahl-Hereaeus vacuum degassing) process. After adding Ca-containing cored wire, the inclusions were transformed into CaO–Al_(2)O_(3) in the steel. With the progress of smelting, the cleanliness of molten steel became worse, and the equivalent diameter of inclusions was at a higher level. Mg-treatment had a good effect on the modification of inclusions. After Mg-containing cored wire was added to the steel, Al_(2)O_(3) and CaO–Al_(2)O_(3) in the steel were transformed into MgO, MgO·Al_(2)O_(3), and CaO–MgO–Al_(2)O_(3) inclusions, which were basically spherical. The initial precipitated MgO became the core of other inclusions in the steel, which promotes the precipitation of MgO·Al_(2)O_(3). After Mg-treatment, almost no unmodified calcium aluminate inclusions existed in the hot rolled plate, and the cleanliness of the steel was improved. The effect of Ca and Mg on the transformation of inclusions in pipeline steel was studied by thermodynamic calculation, the result of which is consistent with the experimental results.展开更多
基金supported by the National Natural Science Foundation of China(NSFC,Grant Nos.11872120,12102050)Key Laboratory of Explosion Science and Technology(Grant No.QNKT22-01).
文摘The new CL-20(hexanitrohexaazaisowurtzitane)type aluminized explosives in the overdrive detonation(ODD)conditions of the core problem is how to accurately represent the state of the overdrive detonation products.To this end,this paper is based on the impedance matching method to test the ODD conditions of CL-20 type aluminium explosive particle velocity.Calculated the interfacial pressure of the shock wave in different media.Determined the characteristic parameters of the reaction zone of the detonation of CL-20 aluminized explosives.Calibrated the parameters of the JoneseWilkinseLee(JWL)+γ equation for the detonation products(DPs).Revealed the effect of different DPs equation of state(EOS)on the Hugoniot pressure of ODD.The results indicate that when the content of aluminum powder ranges from 0%to 30%,the duration of the ODD reaction zone and the width of the detonation reaction zone of the CL-20-based aluminized explosive are directly proportional to the content of aluminum powder.The width of the detonation reaction zone is increased by 1.97 times to 2.7 times compared to that of the reaction zone without the addition of aluminum powder.However,the energy release efficiency of the detonation reaction zone is inversely proportional to the content of aluminum powder.When the aluminum powder content was held constant,the incorporation of AP caused a 25%reduction in the energy release efficiency of the detonation reaction zone.Compared with existing ODD state equations,the JWL +γ equation is superior in calibrating overpressure Hugoniot data and the isentropic expansion in the C-J state.The deviation between calculated pressure results and experimental measurements is within 6%.
基金supported by the National Natural Science Foundation of China(Grant No.11832006)。
文摘Afterburning behind the detonation front of an aluminized explosive releases energy on the millisecond timescale,which prolong the release of detonation energy and the energy release at different stages also shows significant differences.However,at present,there are few effective methods for evaluating the energy release characteristics of the middle reaction stage of such explosives,which can have a duration of tens to hundreds of microseconds.The present work demonstrates an approach to assessing the midstage of an aluminized explosive detonation based on a water push test employing a high degree of confinement.In this method,the explosive is contained in a steel cylinder having one end closed that is installed at the bottom of a transparent water tank.Upon detonation,the gaseous products expand in one direction while forcing water ahead of them.The resulting underwater shock wave and the interface between the gas phase products and the water are tracked using an ultra-high-speed framing and streak camera.The shock wave velocity in water and the expansion work performed by the gaseous detonation products were calculated to assess the energy release characteristics of aluminized explosives such as CL-20 and RDX in the middle stage of the detonation reaction.During the middle stage of the detonation process of these aluminized explosives,the aluminum reaction reduced the attenuation of shock waves and increased the work performed by gas phase products.A higher aluminum content increased the energy output while the presence of oxidants slowed the energy release rate.This work demonstrates an effective means of evaluating the performance of aluminized explosives.
基金National Natural Science Foundation of China(Grant No.11872120).
文摘Taking CL-20(Hexanitrohexaazaisowurtzitane)-based aluminized explosives with high gurney energy as the research object, this research experimentally investigates the work capability of different aluminized explosive formulations when driving metal flyer plates in the denotation wave propagation direction.The research results showed that the formulations with 43 μm aluminum(Al) powder particles(The particle sizes of Al powder were in the range of 2~43 μm) exhibited the optimal performance in driving flyer plates along the denotation wave propagation direction. Compared to the formulations with Al powder 13 μm, the formulations with Al powder 2 μm delivered better performance in accelerating metal flyer plates in the early stage, which, however, turned to be poor in the later stage. The CL-20-based explosives containing 25% Al far under-performed those containing 15% Al. Based on the proposed quasi-isentropic hypothesis, relevant isentropy theories, and the functional relationship between detonation parameters and entropy as well as Al reaction degree, the characteristic lines of aluminized explosives in accelerating flyer plates were theoretically studied, a quasi-isentropic theoretical model for the aluminized explosive driving the flyer plate was built and the calculation methods for the variations of flyer plate velocity, Al reaction degree, and detonation product parameters with time and axial positions were developed. The theoretical model built is verified by the experimental results of the CL-20-based aluminized explosive driving flyer plate. It was found that the model built could accurately calculate the variations of flyer plate velocity and Al reaction degree over time. In addition, how physical parameters including detonation product pressure and temperature varied with time and axial positions was identified. The action time of the positive pressure after the detonation of aluminized explosives was found prolonged and the downtrend of the temperature was slowed down and even reversed to a slight rise due to the aftereffect reaction between the Al powder and the detonation products.
基金Projects(CKJB201205,QKJB201202,YJK201307)supported by the Nanjing Institute of Technology,China
文摘The outermost coating with single phase Ni2Al3 was obtained on copper surface by electrodepositing nickel followed by slurry pack aluminizing at 800 °C for 12 h. The oxidation resistance and microstructure of the coating oxidized in ambient air at 1000 °C for 25-250 h were investigated using SEM, X-ray diffraction and optical microscope methods. The results show that the copper with single phase Ni2Al3 coating possesses the best high temperature oxidation resistance, and the mass gain of the coating is 1/15 that of pure copper and 1/2 that of nickel coating, respectively. The specimen surface after being oxidized for 25 h still comprises Ni2Al3 phase. However, when the time of oxidizing treatment increases to 50 h, the Ni Al phase is formed. It is also found that the Ni2Al3 phase completely turns into Ni Al phase after oxidizing treatment for 100 h and above. The Ni Al coating shows excellent high temperature oxidation resistance when oxidation time is 250 h.
文摘Pressure histories were tested in a 500-L chamber to identify the pressure load in confined explosion from aluminized explosives. Different aluminized explosives with Al/O, ranging from 0.25 to 1.23, were used. The recorded pressure curves could express the reflection of initial shock wave and the after burning combustion of aluminum. As there is no objective way to gain quasi-static pressure(P_(QS)),method of multipoint averaging was used in smoothing the original pressure curves to gain the P_(QS). The P_(QS),rising time of pressure(t_(QS)) which stands for the duration of the initial reflected shock wave, and attenuation coefficient(ω) which stands for the supportive effects of the combustion of aluminum to the P_(QS) are used to characterize the pressure load in the confined explosion from aluminized explosives. The research results showed that the Al/O significantly affected the three characteristic quantities. With the increase of Al/O, the P_(QS) increased at first and decreased later, gaining maximum at Al/O=0.99; the t_(QS)sustained growth and the ω decreased at first and increased later, gaining minimum at AI/O=0.99.
基金Item Sponsored by Key Science and Technology Plan Foundation of Henan of China (0423023500) and Natural ScienceFoundation of Henan Province (0511021600)
文摘The effects of the addition of rare earth （RE） elements on the void band in the diffusion layer, and the re sistances to both oxidation and spalling of aluminized steel were investigated through high temperature oxidation and spalling tests. The results showed that RE had significant effects on the void band in the diffusion layer and the properties of aluminized steel. After diffusion treatment, a considerable number of the voids between the middle layer and transitional layer of pure aluminized coating, aggregated into wavy-line-shaped void bands parallel to the outer surface. For the RE added aluminized coating, only a few voids aggregated into intermittent block shapes. During high temperature oxidation at 800 ℃ for 200 h, the wavy void band of pure aluminized coating aggregated further into a linear crack parallel to the outer surface, and the internal oxidation occurred within them; the open cracks perpendicular to the surface penetrated through the diffusion layer. For the RE added aluminized coating, only a few voids aggregated into intermittent meniscus shapes. During cyclic spalling tests, the peeling, spallation, and pulver ulent cracking occurred along the void band in the diffusion layer of pure aluminized coating, but only a little spallation occurred in the diffusion layer of the RE-added aluminized coating, in which cracks perpendicular to the surface were much smaller than those of pure aluminized coating and did not penetrate through the diffusion layer. It is evident that RE addition can restrain the formation and aggregation of voids and subsequently improve the resistances to oxidation and spalling. The mechanism of the RE effect on the void band in the diffusion layer is also discussed.
基金This paper is supported by the project of State Key Laboratory of Explosion Science and Technology(Beijing Institute of Technology).The project number is NO.QNKT19-04.
文摘This work aims to research the effects on the early responses of the air-backed plate subjected to the loading generated by the underwater explosion with aluminized explosives.The loading characteristics of underwater explosion for ideal explosive(TNT),aluminized explosives(RS211 and RBUL) are obtained experimentally.The tested aluminized explosives have different energy output compared with TNT.Based on the Taylor plate theory,the early responses of the air-backed steel plate affected by the measured loading is analyzed.The analytical results indicate that the pressure curve of the shock wave within 1 time decay constant is the main factor affecting the kick-off velocity of the plate when cavitation occurring.The velocity responses of the plate produced by the loading of RS211 and RBUL are obviously different with that of an equivalent TNT charge,which also indicates validity and suitability should be noticed in the case of substituting TNT for aluminized explosives.Moreover,the uncertainties in the responses of the plate produced by RS211 and RBUL are much larger than TNT.
文摘To investigate the shock wave characteristics of RDX-based aluminized explosives,air blast tests were conducted for measuring the parameters of 10 kg aluminized explosives which contained 0-40% aluminum.The results showed that with the increasing of aluminum content,the overpressures and impulses increase at first and then decrease within 7 m or 5 m,which reached the maximum when aluminum content was 20% or 30%.Power exponential formulas are used to fit the shock wave parameters vs scaled distance,where an equal weight of TNT is used to calculate the scaled distance.The overpressures of HL0 and TNT in tested locations not only conform to the similar law,but also conform to the same attenuation law after gaining the scaled distances of equal TNT mass.The pre-exponential factors of overpressure and impulse,kp and kI,decrease along with the increasing of Al content and keep the same pace as the calculated PCJ）.The attenuation coefficients a_P and aIincrease at first and decrease later with the increasing of aluminum content,and they reached the maximal values with30% Al containing,which keeps the same pace as the calculated QV.
文摘Cis-and trans-1,3,4,6-tetranitroglycouril(TNGU, Sorguyl) have been considered for density functional treatment at the levels of B3LYP/6-31 G(d,p) and B3LYP/cc-PVDZ. Cis-TNGU has been found to be more stable than its trans isomer. Then, mono and dialuminized(cis-TNGU + Al and cis-TNGU+2Al) have been subjected to theoretical treatment at the level of B3LYP/6-31 + G(d). The spin states of the aluminized cis-TNGU composites have been considered as well. Although, cis-TNGU + Al(doublet) is found to be structurally stable, cis-TNGU+2Al singlet and triplet composites undergo certain bond cleavages.Structural and some quantum chemical properties, IR-UV spectra etc. have been presented.
基金National Natural Science Foundation of China(Grant No.11872120).
文摘A quasi-isentropic study on the process of driving a cylinder with aluminized explosives was carried out to examine the influence of the aluminum(Al) reaction rate on cylinder expansion and the physical parameters of the detonation products. Based on the proposed quasi-isentropic hypothesis and relevant isentropic theories, the characteristic lines of aluminized explosives driving a cylinder were analyzed,and a quasi-isentropic model was established. This model includes the variation of the cylinder wall velocity and the physical parameters of the detonation products with the Al reaction degree. Using previously reported experimental results, the quasi-isentropic model was verified to be applicative and accurate. This model was used to calculate the physical parameters for cylinder experiments with aluminized cyclotrimethylenetrinitramine explosives with 15.0 % and 30.0 % Al content. The results show that this quasi-isentropic model can be used not only to calculate the cylinder expansion rule or Al reaction degree, but also to calculate the physical parameters of the detonation products in the process of cylinder expansion. For explosives with 15.0 % and 30.0 % Al, 24.3 % and 18.5 % of the Al was found to have reacted at 33.9 μs and 34.0 μs, respectively. The difference in Al content results in different reaction intensity, occurrence time, and duration of two forms of reaction(diffusion and kinetic) between the Al powder and the detonation products;the post-detonation burning reaction between the Al powder and the detonation products prolongs the positive pressure action time, resulting in a continuous rise in temperature after detonation.
基金Supported by the National Natural Science Foundation of China under Grant No 11172042
文摘The time-dependent Jones Wilkins-Lee equation products for aluminized explosives. To obtain the of state （JWL-EOS） is applied to describe detonation state time-dependent JWL-EOS parameters, cylinder tests and underwater explosion experiments are performed. According to the result of the wall radial velocity in cylinder tests and the shock wave pressures in underwater explosion experiments, the time-dependent JWL-EOS parameters are determined by iterating these variables in AUTODYN hydroeode simulations until the experimental values are reproduced. In addition, to verify the reliability of the derived JWL-EOS parameters, the aluminized explosive experiment is conducted in concrete. The shock wave pressures in the affected concrete bodies are measured by using manganin pressure sensors, and the rod velocity is obtained by using a high-speed camera. Simultaneously, the shock wave pressure and the rod velocity are calculated by using the derived time-dependent JWL equation of state. The calculated results are in good agreement with the experimental data.
文摘Hot-dip aluminizing（HDA） is a proven surface coating technique for improving the oxidation and corrosion resistance of ferrous substrates. Although extensive studies on the HDA of plain carbon steels have been reported, studies on the HDA of stainless steels are limited. Because of the technological importance of stainless steels in high-temperature applications, studies of their microstructural development during HDA are needed. In the present investigation, the HDA of AISI 321 stainless steel was carried out in a pure Al bath. The microstructural features of the coating were studied using scanning electron microscopy and transmission electron microscopy. These studies revealed that the coating consists of two regions： an Al top coat and an aluminide layer at the interface between the steel and Al. The Al top coat was found to consist of intermetallic phases such as Al_7Cr and Al_3Fe dispersed in an Al matrix. Twinning was observed in both the Al_7Cr and the Al_3Fe phases. Furthermore, the aluminide layer comprised a mixture of nanocrystalline Fe_2Al_5, Al_7Cr, and Al. Details of the microstructural features are presented, and their formation mechanisms are discussed.
文摘Microstructures,high-temperature oxidation and wear resistance of hot dipping Al-Si-Y coating on SCH12 heat resistant cast steel were investigated in this study.The aluminized coating was characterized by scanning electron microscopy(SEM),energy dispersive X-ray spectrometry(EDX)and X-ray diffraction(XRD).The results showed that the coating was composed of the Al-rich outer layer and the intermetallics inner layer.In the Al-rich layer,some Y-rich precipitates and Fe-Al-Si-Cr precipitates could be observed.The intermetallics layer presented three layers induced by the increase of Fe,Cr,Ni content and the corresponding decrease of Al,Si content.The oxidation tests were conducted in still air at 850℃for up to 100 h.After oxidation,a top oxide scale composed of mainlyα-Al2O3,Al5Y3O12 was formed on the steel surface.The intermetallics beneath the oxide scale consisted of mainly FeAl and small amount of Fe2Al5 and Cr3Si phase.The mass gain of the coated and uncoated SCH1steel is 0.45 mg/cm 2 and 0.57 mg/cm 2,respectively.The wear resistance was investigated using a high-temperature pin-on-disc tribometer at 650℃.The wear rate for the coated and uncoated steel is 0.45μm 3 /μm.N and 3.01μm 3 /μm.N,respectively.The high temperature wear tests and oxidation tests results demonstrated that the yttrium-modified aluminized specimen had significantly improved high-temperature wear resistance and equivalent oxidation resistance compared with the original SCH12 specimen.
基金supported by the Liaoning Revitalization Talents Program (XLYC2203133)the Fundamental Research Funds for the Central Universities (N2302018)the Ningbo Yuyao City Science and Technology Plan Project (2023J03010010)
文摘The corrosion behavior of Super304H,HR3C and related aluminized coatings under K_(2)SO_(4)+Na_(2)SO_(4)(mass ratio=1:1)and K_(2)SO_(4)+Na_(2)SO_(4)+KCl(45:45:10)deposits in a mixed gas of 0.5SO_(2)–4O_(2)–20H_(2)O-75.5CO_(2)(vol.%)at 700℃were studied.Super304H undergoes severe corrosion under both deposits,the addition of KCl did not significantly accelerate the corrosion process but resulted in an extremely porous and thickness-doubled scale.While HR3C with higher Cr content shows excellent corrosion resistance in Cl free environment due to the formation of dense Cr_(2)O_(3).Due to the involvement of Cl,HR3C can no longer resist the corrosion of the salts.The corrosion depth increases by two orders of magnitude and becomes as severe as Super304H.Aluminizing significantly improved the corrosion resistance of the alloys on account ofα-Al_(2)O_(3)formation by a new mechanism.The addition of KCl had little effect on this mechanism and only increased the thickness of the corrosion products slightly.
基金financially supported by the National Key R&D Program of China(No.2020YFB2010404)
文摘Aluminized coating was prepared on K452 superalloy by chemical vapor deposition(CVD)technique.The oxidation/corrosion behavior of alloy and coating were investigated at 750℃in air,air with solid NaCl deposit and moist air with solid NaCl deposit,respectively.The microstructure and composition of samples were characterized by SEM/EDS and XRD techniques.The results demonstrated that aluminized coating exhibited better oxidation/corrosion resistance than K452 alloy in the three environments above.And the main oxidation and corrosion products of alloy were Cr_(2)O_(3)and NiO,respectively.This indicated that Ni participated in the corrosion process due to the depletion of Cr during accelerated corrosion.Therefore,the established corrosion scale was non-protective,which could not protect underlying alloy from accelerated corrosion.Contrarily,the main oxidation and corrosion products of coating were protective Al_(2)O_(3),which acted as a barrier to separate coating from NaCl and oxygen,interrupting the self-sustainable accelerated corrosion.Additionally,the presence of water vapor was beneficial in reducing the spallation of corrosion products within a short time.The mechanisms of K452 alloy and aluminized coating in the three environments above were discussed in detail.
基金the Natural Sciences and Engineering Research Council of Canada(NSERC)for funding this researchThis research used a high temperature confocal laser scanning microscope-VL2000DX-SVF17SP funded by Canada Foundation for Innovation John Evans Leaders Fund(CFI JELF,Project Number:32826),a PANalytical X’Pert diffraction instrument located at the Centre for crystal growth,Brockhouse Institute for Materials Research,and a scanning electron microscope-JEOL 6610 located at the Canadian Centre for Electron Microscopy at McMaster University.W.Mu would like to acknowledge Swedish Iron and Steel Research Office(Jernkonteret),STINT and SSF for supporting the time for international collaboration research regarding clean steel.
文摘Dissolution kinetics of CaO·2Al_(2)O_(3)(CA_(2))particles in a synthetic CaO-Al_(2)O_(3)-SiO_(2)steelmaking slag system have been investigated using the high-temperature confocal laser scanning microscope.Effects of temperature(i.e.,1500,1550,and 1600℃)and slag composition on the dissolution time of CA_(2)particles are investigated,along with the time dependency of the projection area of the particle during the dissolution process.It is found that the dissolution rate was enhanced by either an increase in temperature or a decrease in slag viscosity.Moreover,a higher ratio of CaO/Al_(2)O_(3)(C/A)leads to an increased dissolution rate of CA_(2)particle at 1600℃.Thermodynamic calculations suggested the dissolution product,i.e.,melilite,formed on the surface of the CA_(2)particle during dissolution in slag with a C/A ratio of 3.8 at 1550℃.Scanning electron microscopy equipped with energy dispersive X-ray spectrometry analysis of as-quenched samples confirmed the dissolution path of CA_(2)particles in slags with C/A ratios of 1.8 and 3.8 as well as the melilite formed on the surface of CA_(2)particle.The formation of this layer during the dissolution process was identified as a hindrance,impeding the dissolution of CA_(2)particle.A valuable reference for designing or/and choosing the composition of top slag for clean steel production is provided,especially using calcium treatment during the secondary refining process.
基金Supported by National Natural Science Foundation of China(Grant Nos.52075048,51675058,12232004)Hunan Provincial Excellent Youth Project of the Education Department(Grant No.21B0304)+2 种基金Natural Science Foundation of Hunan Province(Grant No.2023JJ30025)Science and Technology Innovation Program of Hunan Province(Grant No.2023RC1058)Scientific Research Innovation Project for Graduate Student of Changsha University of Science and Technology(Grant No.CLSJCX22096)。
文摘The high-temperature oxidation resistance of AISI 321 stainless steel used in solar thermal power heat exchangers determines its service life.In this study,aluminizing and subsequent laser shock peening(LSP)treatments were employed to improve the high-temperature oxidation resistance of AISI 321 stainless steel at 620°C.These two treatments decreased the oxidation rate of AISI 321 steel.Specifically,the optimal oxidation resistance was observed in aluminized steel before oxidation for 144 h owing to the increased entropy of the LSP-treated specimen.After 144 h,LSP-treated steel achieved the best oxidation resistance because of the formation of a protectiveα-Al2O3film.Moreover,the large amount of subgrain boundaries formed on the aluminized layer of the LSP-treated samples could act as short-circuit paths for the outward diffusion of Al,facilitating the rapid nucleation ofα-Al2O3.Meanwhile,the aluminized layer could isolate the contact between the oxidation environment and matrix,thereby decreasing the oxidation rate.Furthermore,the minimum oxidation parabolic constant was calculated for LSP-treated steel(6.45787×10^(-14)),which was 69.18%and 36.36%that of aluminized and 321 steel,respectively,during the entire oxidation process.Therefore,the combination of aluminizing and LSP treatments can improve the high-temperature oxidation resistance of 321 stainless steel,providing a new idea for its surface treatment to achieve a long service life at high temperatures.
文摘In order to prepare high density magnesium aluminate spinel materials,the light-burned magnesia and alumina powder were used as the main raw materials.Active magnesium aluminate spinel powders were synthesized at different temperatures,and the sintering properties of the synthesized materials were characterized.The results show that the optimal light-burned temperature for synthesizing active magnesium aluminate spinel raw materials with small grain sizes and high sintering activity is 1400℃.The active spinel raw materials were sintered at 1750℃ for 3 h to form a dense spinel material,in which the spinel grains were well developed,exhibited a dense interlocking structure,and were uniformly distributed,with an average grain size of about 7.26μm.The bulk density and apparent porosity of the dense spinel material were 3.29 g·cm^(-3) and 3.5%,respectively.
基金Funded by the National Key Research and Development Program of China(No.2022YFC3803400)National Natural Science Foundation of China(Nos.52378255,52278270)+1 种基金Shanghai Municipal Science and Technology Major Project(No.2021SHZDZX0100)the Fundamental Research Funds for the Central Universities and the Experimental Center of Materials Science and Engineering in Tongji University。
文摘We focused on the efflorescence induced microstructural evolution of ettringite-rich systems prepared with calcium aluminate cement(CAC)and anhydrite.The effects of anhydrite on the visible efflorescence,and the corresponding capillary absorption of CAC-anhydrite mortars were revealed.The composition and microstructure of efflorescence-causing substances were investigated by optical microscope,in-situ Raman spectroscopy,scanning electron microscope,energy dispersive spectrometer,thermogravimetric analysis,and differential scanning calorimetry,at multi-scales.Results indicate that,besides the calcium carbonate,ettringite is another main component of efflorescence-causing substances.Compared with the neat CAC mortars,the addition of anhydrite has a significant effect on the degree of efflorescence by acting on the composition of hydration products and pore structure.In addition,methods are proposed for the prevention of efflorescence of CAC-anhydrite binary system.
基金funded by the National Natural Science Foundation of China(Nos.52104334,51874195 and 52074179)Center for Advanced Solidification Technology(CAST)and State Key Laboratory of Advanced Special Steel.
文摘In order to investigate the modification behavior and regularity of inclusions in X80 pipeline steel by Mg-treatment, the comparative industrial experiments of Mg-treatment and Ca-treatment in X80 pipeline steel were carried out. Mg and Ca were added to the steel in the form of cored wire after RH (Ruhrstahl-Hereaeus vacuum degassing) process. After adding Ca-containing cored wire, the inclusions were transformed into CaO–Al_(2)O_(3) in the steel. With the progress of smelting, the cleanliness of molten steel became worse, and the equivalent diameter of inclusions was at a higher level. Mg-treatment had a good effect on the modification of inclusions. After Mg-containing cored wire was added to the steel, Al_(2)O_(3) and CaO–Al_(2)O_(3) in the steel were transformed into MgO, MgO·Al_(2)O_(3), and CaO–MgO–Al_(2)O_(3) inclusions, which were basically spherical. The initial precipitated MgO became the core of other inclusions in the steel, which promotes the precipitation of MgO·Al_(2)O_(3). After Mg-treatment, almost no unmodified calcium aluminate inclusions existed in the hot rolled plate, and the cleanliness of the steel was improved. The effect of Ca and Mg on the transformation of inclusions in pipeline steel was studied by thermodynamic calculation, the result of which is consistent with the experimental results.
