High-temperature compressive deformation behaviors of Mg–6Zn–1.5Y–0.5Ce–0.4Zr alloy were investigated at temperatures and strain rates ranging from 523 to 673 K and from 0.001 to 1 s~(-1),respectively.The studied ...High-temperature compressive deformation behaviors of Mg–6Zn–1.5Y–0.5Ce–0.4Zr alloy were investigated at temperatures and strain rates ranging from 523 to 673 K and from 0.001 to 1 s~(-1),respectively.The studied alloy was mainly composed ofα-Mg,Mg_(3)Zn_(6)Y(I phase),Mg–Zn–Ce and Mg_(3)Zn_(3)Y_(2)(W phase).The constitutive equation of Mg alloy was obtained,and the apparent activation energy(Q)was determined as 200.44 k J/mol,indicating that rare earth phase increases the difficulty of deformation.The work hardening involves three stages:(1)linear hardening stage;(2)strain hardening stage;and(3)softening and steady-state stage.During these three stages,the dislocation aggregation and tangling,dynamic recovery and recrystallization occur sequentially.To characterize the dynamic recrystallization(DRX)volume fraction,the DRX kinetics was investigated using the Avrami-type equation.The deformation mechanism of magnesium alloy under different Zener–Hollomon parameter(Z)value conditions was also studied.At high Z values and intermediate conditions,dislocations rapidly generate and pile up in the alloy.Recrystallization is hardly seen at this time.At low Z condition,the DRX occurs in the alloy.展开更多
The hot deformation behavior of extruded AZ80 magnesium alloy was studied through hot compression tests performed at temperatures ranging from 250 to 450 ~C with strain rates varying from 0.001 to 10 s-1. The flow str...The hot deformation behavior of extruded AZ80 magnesium alloy was studied through hot compression tests performed at temperatures ranging from 250 to 450 ~C with strain rates varying from 0.001 to 10 s-1. The flow stress was corrected due to the deformation heating. The Zener-Hollomon parameter （Z parameter） and processing map were established to describe the hot deformation behavior. The results indicate that the applicable deformation should be conducted at the strain rate of 0.1 s-~ and the temperature range of 350-400 ~C. Besides, the relationship between the microstructure evolution and Z parameter was also discussed. High temperature and low strain rate result in a low Z parameter, which leads to full dynamic recrystallization （DRX） and large DRX grain size in the microstructure. Considering processing map and microstructure, the hot deformation should be carried out at the temperature of 400 ~C and the strain rate of 0.1 s 1.展开更多
The automobile suspension parts of a high strength 6xxx aluminum alloy were produced using a novel technique known as near net shape casting for forging stock preparation. Based on the outline dimension of the forging...The automobile suspension parts of a high strength 6xxx aluminum alloy were produced using a novel technique known as near net shape casting for forging stock preparation. Based on the outline dimension of the forging stock, the shape of the ingot was designed as the near net shape and its casting process was studied by the numerical simulation and experimental investigation. The results show that the shrinkage of the ingot was highly correlated to its shape parameters and could be successfully forecast by the stimulation model. The casting parameters of the near net shape ingot were optimized and the near net shape 6xxx aluminum alloy ingots free of defects were cast in the laboratory. In order to obtain high performance forged suspension parts, the hot compression tests of the ingot were carried out. The results show that the subgrain fraction of the forged ingot was strongly affected by Zener-Hollomon parameters （Z parameters）. The intermediate Z parameters, 1.09×10^16 s^-1, will contribute to the larger number fraction of subgrains inside the forged ingot, which contributes to the high performance of the forged products.展开更多
The dynamic recrystallization and carbides precipitation of the Cr-Co-Mo-Ni bearing steel were investigated by hot compression tests performed at temperatures ranging from 850 ℃to 1080 ℃ with strain rate of 1-20 s-1...The dynamic recrystallization and carbides precipitation of the Cr-Co-Mo-Ni bearing steel were investigated by hot compression tests performed at temperatures ranging from 850 ℃to 1080 ℃ with strain rate of 1-20 s-1. The activation energy（Q） for the tested steel is calculated to be around 682.99 k J/mol at a deformation strain of 0.6. Microstructural analysis by SEM shows that the dynamic recrystallization（DRX） behavior is dependent sensitively on the deformation strain, temperature and strain rate, while an exponential relationship between DRX grain size and Z parameter is obtained from the computational formula. Moreover, the M6C-type carbides（〈1 μm） act as the main prohibitor of grain coarsening, and the polynomial regression relationship between them is worked out. With electron backscatter diffraction（EBSD） observation, DRX is the main nucleation mechanism responsible for the formation of new grains during hot compression. In conclusion, the interaction between DRX affected by hot deformation parameters and carbides precipitation determines the ultimate grain size refinement.展开更多
The microstructural evolution of AA6061 and Mn-bearing Al-Mg-Si-Cu alloys was studied by compression tests that were carried out between 300 and 500 °C with a wide range of strain rates. Compared to the AA6061 al...The microstructural evolution of AA6061 and Mn-bearing Al-Mg-Si-Cu alloys was studied by compression tests that were carried out between 300 and 500 °C with a wide range of strain rates. Compared to the AA6061 alloy, the large amount of α-Al(MnFeCr)Si dispersoids in the Mn-bearing alloy yielded a significant increase in the flow stress under all deformation conditions. The effects of the deformation parameters on the evolution of the microstructure were studied using electronic backscatter diffraction measurements. The predominant softening mechanism of both alloys was dynamic recovery. The presence of α dispersoids in Mn-bearing alloys effectively refined the size of substructures with misorientation angles in the range of 2°-5°, which retarded the dynamic recovery. To predict the subgrain size under various deformation conditions, the threshold stresses that were caused by α dispersoids were calculated by the modified Orowan equation and incorporated into a conventional constitutive equation. The subgrain size that was predicted by the modified constitutive equation showed satisfactory agreement with the experimental measurements.展开更多
To realize numerical simulation of rolling and obtain the hot forming process parameters for X70 HD steel, the flow stress behaviors of X70 HD steel were investigated under different temperatures（820-1100 ℃ and stra...To realize numerical simulation of rolling and obtain the hot forming process parameters for X70 HD steel, the flow stress behaviors of X70 HD steel were investigated under different temperatures（820-1100 ℃ and strain rates（0.01-10 s-1） on a Gleeble-3500 thermo-simulation machine. A new flow stress model was established. The linear and exponential relationship methods were applied to the parameters with respect to temperature and deformation rates. The rise of curve ends under certain conditions was analyzed. The flow stress of X70 HD steel predicted by the proposed model agrees well with the experimental results. So, it greatly improves the precision of the metal thermoplastic processing through finite element method and practical application of engineering.展开更多
The hot deformation behavior and microstructure evolution of high manganese transformation induced plasticity steel(Fe - 20Mn - 3Si - 3Al) were investigated by using hot compression test in a temperature range from 80...The hot deformation behavior and microstructure evolution of high manganese transformation induced plasticity steel(Fe - 20Mn - 3Si - 3Al) were investigated by using hot compression test in a temperature range from 800℃to 1 050℃and strain rate ranging from 0.01 s^(-1) to 5.0 s^(-1).The effects of temperature,strain rate,and true strain on the flow behavior and microstructures of high manganese transformation induced plasticity steel were discussed.The results show that the dynamic recrystallization occurs only at higher temperature and lower strain rate.Hot deformation behaviors of high manganese transformation induced plasticity steel were sensitive to temperature and strain rate.The apparent stress exponent and the apparent activation energy of the investigated steel were about 4.280 and 463.791 kJ/mol, respectively.The apparent activation energy of the high manganese transformation induced plasticity steel was approached to the austenitic stainless steel(400 -500 kJ/mol).The hot working equation is obtained. Hot deformation peak stress increased with increasing of the value of lnZ.Peak stress and InZ exhibits a linear variation,the linear correlation coefficient was 0.988 9.The results show that the dynamic recrystallization was prone to occur when lnZ≤43.842 26 and Z≤1.098×10^(19),and better hot deformation properties would be obtained under this condition.展开更多
A new general parameterization with eight mixing parameters among Z, γ and an extra neutral gauge boson Z is proposed and subjected to phenomenological analysis. We show that in addition to the conventional Weinberg ...A new general parameterization with eight mixing parameters among Z, γ and an extra neutral gauge boson Z is proposed and subjected to phenomenological analysis. We show that in addition to the conventional Weinberg angle θW , there are seven other phenomenological parameters, G , ξ, η, θl, θr, r and l, for the most general Z-γ-Z mixings, in which parameter G arises due to the presence of an extra Stueckelberg- type mass coupling. Combined with the conventional Z-Z mass mixing angle θ , the remaining six parameters, ξ, η, θl θ , θr θ , r and l, are caused by general kinetic mixing. In all eight phenomenological parameters, θW , G , ξ, η, θl, θr , r and l, we can determine the Z-Z mass mixing angle θ and the mass ratio MZ/MZ . The Z-γ-Z mixing that we discuss are based on the model-independent description of the extended electroweak chiral Lagrangian （EWCL） previously proposed by us. In addition, we show that there are eight corresponding independent theoretical coefficients in our EWCL, which are fully fixed by our eight phenomenological mixing parameters. We further find that the experimental measurability of these eight parameters does not rely on the extended neutral current for Z , but depends on the Z-Z mass ratio.展开更多
基金financially supported by the National Key R&D Program of China(2016YFB0301100)the Natural Science Foundation of Chongqing,China(cstc2019jcyj-msxmX0505)the support of the“111 Project”(B16007)by the Ministry of Education and Fundamental Research Fund of Central Universities in China(Grant No.2018CDJDCL0019)。
文摘High-temperature compressive deformation behaviors of Mg–6Zn–1.5Y–0.5Ce–0.4Zr alloy were investigated at temperatures and strain rates ranging from 523 to 673 K and from 0.001 to 1 s~(-1),respectively.The studied alloy was mainly composed ofα-Mg,Mg_(3)Zn_(6)Y(I phase),Mg–Zn–Ce and Mg_(3)Zn_(3)Y_(2)(W phase).The constitutive equation of Mg alloy was obtained,and the apparent activation energy(Q)was determined as 200.44 k J/mol,indicating that rare earth phase increases the difficulty of deformation.The work hardening involves three stages:(1)linear hardening stage;(2)strain hardening stage;and(3)softening and steady-state stage.During these three stages,the dislocation aggregation and tangling,dynamic recovery and recrystallization occur sequentially.To characterize the dynamic recrystallization(DRX)volume fraction,the DRX kinetics was investigated using the Avrami-type equation.The deformation mechanism of magnesium alloy under different Zener–Hollomon parameter(Z)value conditions was also studied.At high Z values and intermediate conditions,dislocations rapidly generate and pile up in the alloy.Recrystallization is hardly seen at this time.At low Z condition,the DRX occurs in the alloy.
文摘The hot deformation behavior of extruded AZ80 magnesium alloy was studied through hot compression tests performed at temperatures ranging from 250 to 450 ~C with strain rates varying from 0.001 to 10 s-1. The flow stress was corrected due to the deformation heating. The Zener-Hollomon parameter （Z parameter） and processing map were established to describe the hot deformation behavior. The results indicate that the applicable deformation should be conducted at the strain rate of 0.1 s-~ and the temperature range of 350-400 ~C. Besides, the relationship between the microstructure evolution and Z parameter was also discussed. High temperature and low strain rate result in a low Z parameter, which leads to full dynamic recrystallization （DRX） and large DRX grain size in the microstructure. Considering processing map and microstructure, the hot deformation should be carried out at the temperature of 400 ~C and the strain rate of 0.1 s 1.
文摘The automobile suspension parts of a high strength 6xxx aluminum alloy were produced using a novel technique known as near net shape casting for forging stock preparation. Based on the outline dimension of the forging stock, the shape of the ingot was designed as the near net shape and its casting process was studied by the numerical simulation and experimental investigation. The results show that the shrinkage of the ingot was highly correlated to its shape parameters and could be successfully forecast by the stimulation model. The casting parameters of the near net shape ingot were optimized and the near net shape 6xxx aluminum alloy ingots free of defects were cast in the laboratory. In order to obtain high performance forged suspension parts, the hot compression tests of the ingot were carried out. The results show that the subgrain fraction of the forged ingot was strongly affected by Zener-Hollomon parameters （Z parameters）. The intermediate Z parameters, 1.09×10^16 s^-1, will contribute to the larger number fraction of subgrains inside the forged ingot, which contributes to the high performance of the forged products.
基金Project(2012AA03A503) supported by the National High Technology Research and Development Program of China
文摘The dynamic recrystallization and carbides precipitation of the Cr-Co-Mo-Ni bearing steel were investigated by hot compression tests performed at temperatures ranging from 850 ℃to 1080 ℃ with strain rate of 1-20 s-1. The activation energy（Q） for the tested steel is calculated to be around 682.99 k J/mol at a deformation strain of 0.6. Microstructural analysis by SEM shows that the dynamic recrystallization（DRX） behavior is dependent sensitively on the deformation strain, temperature and strain rate, while an exponential relationship between DRX grain size and Z parameter is obtained from the computational formula. Moreover, the M6C-type carbides（〈1 μm） act as the main prohibitor of grain coarsening, and the polynomial regression relationship between them is worked out. With electron backscatter diffraction（EBSD） observation, DRX is the main nucleation mechanism responsible for the formation of new grains during hot compression. In conclusion, the interaction between DRX affected by hot deformation parameters and carbides precipitation determines the ultimate grain size refinement.
基金the financial supports from the National Natural Science Foundation of China (No. U1864209)Jincheng Science and Technology Plan Project of Shanxi Province, China (No. 201702014)。
文摘The microstructural evolution of AA6061 and Mn-bearing Al-Mg-Si-Cu alloys was studied by compression tests that were carried out between 300 and 500 °C with a wide range of strain rates. Compared to the AA6061 alloy, the large amount of α-Al(MnFeCr)Si dispersoids in the Mn-bearing alloy yielded a significant increase in the flow stress under all deformation conditions. The effects of the deformation parameters on the evolution of the microstructure were studied using electronic backscatter diffraction measurements. The predominant softening mechanism of both alloys was dynamic recovery. The presence of α dispersoids in Mn-bearing alloys effectively refined the size of substructures with misorientation angles in the range of 2°-5°, which retarded the dynamic recovery. To predict the subgrain size under various deformation conditions, the threshold stresses that were caused by α dispersoids were calculated by the modified Orowan equation and incorporated into a conventional constitutive equation. The subgrain size that was predicted by the modified constitutive equation showed satisfactory agreement with the experimental measurements.
基金Project(51304171)supported by the National Natural Science Foundation of ChinaProject(E2013203248)supported by Natural Science Foundation of Hebei Province of ChinaProject(NECSR-201209)supported by Open Foundation of the National Engineering Research Center for Equipment and Technology of Cold Rolling Strip,China
文摘To realize numerical simulation of rolling and obtain the hot forming process parameters for X70 HD steel, the flow stress behaviors of X70 HD steel were investigated under different temperatures（820-1100 ℃ and strain rates（0.01-10 s-1） on a Gleeble-3500 thermo-simulation machine. A new flow stress model was established. The linear and exponential relationship methods were applied to the parameters with respect to temperature and deformation rates. The rise of curve ends under certain conditions was analyzed. The flow stress of X70 HD steel predicted by the proposed model agrees well with the experimental results. So, it greatly improves the precision of the metal thermoplastic processing through finite element method and practical application of engineering.
文摘The hot deformation behavior and microstructure evolution of high manganese transformation induced plasticity steel(Fe - 20Mn - 3Si - 3Al) were investigated by using hot compression test in a temperature range from 800℃to 1 050℃and strain rate ranging from 0.01 s^(-1) to 5.0 s^(-1).The effects of temperature,strain rate,and true strain on the flow behavior and microstructures of high manganese transformation induced plasticity steel were discussed.The results show that the dynamic recrystallization occurs only at higher temperature and lower strain rate.Hot deformation behaviors of high manganese transformation induced plasticity steel were sensitive to temperature and strain rate.The apparent stress exponent and the apparent activation energy of the investigated steel were about 4.280 and 463.791 kJ/mol, respectively.The apparent activation energy of the high manganese transformation induced plasticity steel was approached to the austenitic stainless steel(400 -500 kJ/mol).The hot working equation is obtained. Hot deformation peak stress increased with increasing of the value of lnZ.Peak stress and InZ exhibits a linear variation,the linear correlation coefficient was 0.988 9.The results show that the dynamic recrystallization was prone to occur when lnZ≤43.842 26 and Z≤1.098×10^(19),and better hot deformation properties would be obtained under this condition.
基金Supported by National Natural Science Foundation of China(10875065,10947152,11005084)
文摘A new general parameterization with eight mixing parameters among Z, γ and an extra neutral gauge boson Z is proposed and subjected to phenomenological analysis. We show that in addition to the conventional Weinberg angle θW , there are seven other phenomenological parameters, G , ξ, η, θl, θr, r and l, for the most general Z-γ-Z mixings, in which parameter G arises due to the presence of an extra Stueckelberg- type mass coupling. Combined with the conventional Z-Z mass mixing angle θ , the remaining six parameters, ξ, η, θl θ , θr θ , r and l, are caused by general kinetic mixing. In all eight phenomenological parameters, θW , G , ξ, η, θl, θr , r and l, we can determine the Z-Z mass mixing angle θ and the mass ratio MZ/MZ . The Z-γ-Z mixing that we discuss are based on the model-independent description of the extended electroweak chiral Lagrangian （EWCL） previously proposed by us. In addition, we show that there are eight corresponding independent theoretical coefficients in our EWCL, which are fully fixed by our eight phenomenological mixing parameters. We further find that the experimental measurability of these eight parameters does not rely on the extended neutral current for Z , but depends on the Z-Z mass ratio.
