Cu-doped TiO2 nanoparticles with different doping contents from 0 to 2.0% （mole fraction） were synthesized through sol-gel method. X-ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS） and field emissi...Cu-doped TiO2 nanoparticles with different doping contents from 0 to 2.0% （mole fraction） were synthesized through sol-gel method. X-ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS） and field emission scanning electron microscope （FE-SEM） were used to characterize the crystalline structure, chemical valence states and morphology of TiO2 nanoparticles. UV-Vis absorption spectrum was used to measure the optical absorption property of the samples. The photocatalytic performance of the samples was characterized by degrading 20 mg/L methyl orange under UV-Vis irradiation. The results show that the Cu-doped TiO2 nanoparticles exhibit a significant increase in photocatalytic performance over the pure TiO2 nanoparticles, and the TiO2 nanoparticles doped with 1.0% Cu show the best photocatalytic performance. The improvement in photocatalytic performance is attributed to the enhanced light adsorption in UV-Vis range and the decrease of the recombination rate of photoinduced electron-hole oair of the Cu-doped TiO2 nanoparticles.展开更多
Cerium-doped titanium dioxide nano-powders were prepared through the sol-gel method and the compound sampies were characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM）, and UV/Vis diffus...Cerium-doped titanium dioxide nano-powders were prepared through the sol-gel method and the compound sampies were characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM）, and UV/Vis diffuse reflectance spectra （DRS）. The photocatalytic activity was evaluated by photocatalytic degradation of phenol in water. The results of XRD, TEM, and DRS show that pure TiO2 and Ce-doped TiO2 powder crystallines are a mixture of anatase and rutile ; the doping can retard the development of the grain size of TiO2 and decrease the diameter of TiO2 from more than 20 nm of pure TiO2 to about 10 nm; the doped TiO2 can improve the light absorption of TiO2 and suitable doping content tends to move the DRS spectrum of TiO2 towards visible light, but too much doping is not good for the light absorption ability. The results of the photocatalytic experiments show that doping with Ce content of 0.08% -0.4% can increase the photocatalytic activity of TiO2; however, doping with Ce content of 0.5% -2.5% can significantly decrease the photocatalytic activity of TiO2. The favorite doping content is 0.4% in the range of our experiments.展开更多
A carbon‐doped TiO2/fly ash support(C‐TiO2/FAS)composite photocatalyst was successfully synthesized through sol impregnation and subsequent carbonization.The carbon dopants were derived from the organic species gene...A carbon‐doped TiO2/fly ash support(C‐TiO2/FAS)composite photocatalyst was successfully synthesized through sol impregnation and subsequent carbonization.The carbon dopants were derived from the organic species generated during the synthesis of the C‐TiO2/FAS composite.A series of analytical techniques,such as scanning electron microscopy(SEM),attenuated total reflection‐Fourier transform infrared(ATR‐FTIR)spectroscopy,X‐ray photoelectron spectroscopy(XPS),and ultraviolet‐visible diffuse reflectance spectroscopy(UV‐Vis DRS),were used to characterize the properties of the prepared samples.The results indicated that C‐TiO2 was successfully coated on the FAS surface.Coupling between C‐TiO2 and FAS resulted in the formation of Si–O–C and Al–O–Ti bonds at their interface.The formation of Si–O–C and Al–O–Ti bonds gave rise to a positive shift of the valence band edge of C‐TiO2 and enhanced its oxidation capability of photogenerated holes as well as photodegradation efficiency of methyl orange.Moreover,the C‐TiO2/FAS photocatalyst exhibited favorable reusability and separability.This work may provide a new route for tuning the electronic band structure of TiO2.展开更多
The neutral hydrogen evolution reaction(HER)is vital in the chemical industry,and its efficiency depends on the interior character of the catalyst.Herein,work function(WF)engineering is introduced via 3d metal(Fe,Co,N...The neutral hydrogen evolution reaction(HER)is vital in the chemical industry,and its efficiency depends on the interior character of the catalyst.Herein,work function(WF)engineering is introduced via 3d metal(Fe,Co,Ni,and Cu)doping for modulating the Fermi energy level of Mo2C.The defective energy level facilitates the free water molecule adsorption and,subsequently,promotes the neutral HER efficiency.Specifically,at a current density of 10 mA/cm2,Cu-Mo2C exhibits the best HER performance with an overpotential of 78 mV,followed by Ni-Mo2C,Co-Mo2C,Fe-Mo2C,and bare Mo2C with 90,95,100,and 173 mV,respectively,and the corresponding Tafel slope values are 40,43,42,56,and 102 mV/dec.The modified WF can also lead to an enhanced photocatalytic efficiency owing to the lowered Schottky barrier and excellent carrier transition across the electrocatalyst–solution interface.When coupling the metal-doped Mo2C samples with TiO2,enhanced photocatalytic neutral HER rates are obtained in comparison to the case with bare TiO2.Typically,the HER rates are 521,404,275,224,147,and 112μmol/h for Cu,Ni,Co,Fe,bare Mo2C,and bare TiO2,respectively.Time-resolved photoluminescence spectroscopy(TRPS)and ultrafast transient absorption(TA)measurements are carried out to confirm the recombination and migration of the photogenerated carriers.The fittedτvalues from the TRPS curves are 22.6,20.5,10.1,4.7,4.0,2.5,and 1.9 ns for TiO2,TiO2-Mo2C,TiO2-Fe-Mo2C,TiO2-Fe-Mo2C,TiO2-Fe-Mo2C,TiO2-Fe-Mo2C,and TiO2-Pt,respectively.Additionally,the fittedτvalues from the TA results are 31,73,and 105 ps for the TiO2-Mo2C,TiO2-Cu-Mo2C,and TiO2-Pt samples,respectively.This work provides in-depth insights into the WF modulation of an electrocatalyst for improving the HER performance.展开更多
Iron（Ⅲ）-doped nanostructure TiO2-coated SiO2 （TiO2/SiO2） particles were prepared using the layer-by-layer assembly technique and their photocatalytic property was studied. TiO2 colloids were synthesized employing...Iron（Ⅲ）-doped nanostructure TiO2-coated SiO2 （TiO2/SiO2） particles were prepared using the layer-by-layer assembly technique and their photocatalytic property was studied. TiO2 colloids were synthesized employing the sol-gel method with TiChas a precursor. The samples were characterized by Fourier transform infrared spectroscopy （FTIR）, SEM, EDS, XPS, and XRD. The experimental results show that TiO2 nanopowders on the surface of SiO2 particles are well distributed, the amount of TiO2 is increased with the adding of coating layers, the pure anatase-TiO2 coating layers are synthesized at 500℃, and the photocatalytic activity of Fe^3＋-doped TiO2/SiO2 is higher than that of undoped TiO2/SiO2.展开更多
A series of Cr doped TiO2 films were prepared by micro arc oxidation （MAO） using an electrolyte of Na3PO4＋K2Cr2O7. X-ray diffraction and scanning electron microscopy revealed that the films mainly consisted of anat...A series of Cr doped TiO2 films were prepared by micro arc oxidation （MAO） using an electrolyte of Na3PO4＋K2Cr2O7. X-ray diffraction and scanning electron microscopy revealed that the films mainly consisted of anatase phase with a porous surface morphology. The films have an excellent photocatalytic effect for degradation of methylene blue and decomposition of water under visible light illumination. This arises from the formation of Cr3＋/Cr4＋ and oxygen vacancy energy levels owing to Cr doping. The former reduces the electron-hole recombination chance, while the latter generates a new gap between the conduction band （CB） and valence band （VB） of TiO2, which lowers the photo energy of the excited electron in the VB to the oxygen vacancy states. The mechanisms for film synthesis during the MAO process are also presented.展开更多
Sulfur doped anatase TiO2 nanoparticles （3 nm- 12 nm） were synthesized by the reaction of titanium tetrachloride, water and sulfuric acid with addition of 3 M NaOH at room temperature. The electro-optical and photoc...Sulfur doped anatase TiO2 nanoparticles （3 nm- 12 nm） were synthesized by the reaction of titanium tetrachloride, water and sulfuric acid with addition of 3 M NaOH at room temperature. The electro-optical and photocatalytic properties of the synthesized sulfur doped TiO2 nanoparticles were studied along with Degussa commercial TiO2 particles （24 nm）. The results show that band gap of TiO2 particles decreases from 3.31 to 3.25 eV and for that of commercial TiO2 to 3.2 eV when the particle sizes increased from 3 nm to 12 nm with increase in sulfur doping. The results of the photocatalytic activity under UV and sun radiation show maximum phenol conversion at the particle size of 4 nm at 4.80% S-doping. Similar results are obtained using UV energy for both phenol conversion and conversion of CO2＋H2O in which formation of methanol, ethanol and proponal is observed. Production of methanol is also achieved on samples with a particle size of 8 and 12 nm and sulfur doping of 4.80% and 5.26%. For TiO2 particle of 4 nm without S doping, the production of methanol, ethanol and proponal was lower as compared to the S-doped particles. This is attributed to the combined electronic effect and band gap change, S dopant, specific surface area and the light source used.展开更多
Lattice‐doping and surface decoration are prospective routes to improve the visible‐light photocatalytic ability of TiO2,but the two techniques are difficult to combine into one preparation process because they are ...Lattice‐doping and surface decoration are prospective routes to improve the visible‐light photocatalytic ability of TiO2,but the two techniques are difficult to combine into one preparation process because they are usually conducted under different conditions,which limits the efficiency of TiO2 modification.In this study,TiO2 was successfully modified by simultaneous lattice‐doping and surface decoration,and the visible‐light photocatalytic capacity was largely improved.Upon comparing the method reported here with previous ones,the most significant difference is that Fe(II)‐phenanthroline was first used as the co‐precursor of the introduced elements of C,N,and Fe.These three elements were simultaneously introduced to TiO2 at high levels by this co‐precursor method.The as‐synthesized photocatalysts were systemically investigated and analyzed by several characterization methods such as XRD,FT‐IR,XPS,Raman spectroscopy,EPR,UV‐Vis DRS,photoluminescence spectra,photocurrent,electrochemical impedance spectra,TEM,and HRTEM.The photocatalytic degradation of 4‐NP under visible‐light irradiation was used to evaluate the photocatalytic activity of the photocatalysts.Based on the experimental data,a probable mechanism for the photocatalytic degradation by the photocatalysts is proposed.This is a novel method of using one source to simultaneously introduce metal and non‐metal elements to TiO2 at high levels,which may provide a new way to prepare highly effective TiO2 photocatalysts.展开更多
Well crystallized niobium-doped TiO; nanotube arrays （TiNbO-NT） were successfully synthesized via the anodization of titanium/niobium alloy sheets, followed with a heat treatment at 550 ℃ for 2 h. Morphology analys...Well crystallized niobium-doped TiO; nanotube arrays （TiNbO-NT） were successfully synthesized via the anodization of titanium/niobium alloy sheets, followed with a heat treatment at 550 ℃ for 2 h. Morphology analysis results demonstrated that both the titanium/niobium alloy microstructure and the dissolution strength of electrolyte played major roles in the formation of nanotube structure. A single-phase microstructure was more favorable to the formation of uniform nanotube arrays, while modulating the dissolution strength of electrolyte was required to obtain nanotube arrays from the alloys with multi-phase microstructures. X-ray diffraction （XRD） and X-ray photoelectron （XPS） analysis results clearly demonstrated that niobium dopants （Nb^5＋） were successfully doped into TiO2 anatase lattice by substituting Ti^4＋ in this approach.展开更多
The hierarchical nanostructured N-doped TiO2 immobilized activated carbon fiber(N-TiO2/ACF)porous composites are fabricated to removal dynamic toluene gas.The results show that nitrogen ions doping and ACF modificatio...The hierarchical nanostructured N-doped TiO2 immobilized activated carbon fiber(N-TiO2/ACF)porous composites are fabricated to removal dynamic toluene gas.The results show that nitrogen ions doping and ACF modification can decrease the band gap of TiO2,leading to red shift toward visible light region.Interestingly,N-TiO2/ACF exhibits strongly synergistic effect owing to high surface area,good crystallinity,enhanced bandgap structure and light harvesting.The toluene removal rate of N-TiO2/ACF composites is 2.29 times higher than that of TiO2.The N-TiO2/ACF for toluene degradation followed the Langmuir-Hinshelwood kinetic model,and the rate constant is enhanced 8 times compared with TiO2.The possible photodegradation pathway and mechanisms are proposed.展开更多
TiO2 doped with C, N and S (TCNS photocatalyst) was prepared by hydrolysis process using titanium iso-propoxide and thiourea. The prepared samples were characterized by X-ray diffraction (XRD), scanning electron micro...TiO2 doped with C, N and S (TCNS photocatalyst) was prepared by hydrolysis process using titanium iso-propoxide and thiourea. The prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photo electron spectroscopy (XPS), BET surface area, FTIR and diffuse reflectance spectra (DRS). The results showed that the prepared catalysts are anatase type and nanosized par-ticles. The catalysts exhibited stronger absorption in the visible light region with a red shift in the adsorption edge. The photocatalytic activity of TCNS photocatalysts was evaluated by the photocatalytic degradation of isoproturon pesticide in aqueous solution. In the present study the maximum activity was achieved for TCNS5 catalyst at neutral pH with 1 g L-1 catalyst amount and at 1.14 x 10-4 M concentration of the pesticide solution. The TCNS photocatalysts showed higher phtocatalytic activity under solar light irradiation. This is attributed to the synergetic effects of red shift in the absorption edge, higher surface area and the inhibition of charge carrier recombination process.展开更多
Using polystyrene （PSt） particles as template, PSt/TiO2 composite particles with AgCl incorporation were prepared through hydrolysis of tetrabutyl titanate in the presence of AgNO3 and NaCl. AgCl doped TiO2 hollow p...Using polystyrene （PSt） particles as template, PSt/TiO2 composite particles with AgCl incorporation were prepared through hydrolysis of tetrabutyl titanate in the presence of AgNO3 and NaCl. AgCl doped TiO2 hollow particles were successfully prepared with the PSt/TiO2 composite microspheres pretreated at 180 ℃ followed by calcination. The morphology of PSt/TiO2 particles and the crystal structures of the AgCl doped TiO2 hollow particles were characterized. The photocatalytic activity of the doped TiO2 hollow particles in degradation of Rhodamine B was tested under UV and visible lights and compared to that with Ag doped TiO2 particles. The results showed that TiO2 hollow particles, either doped with Ag or AgCl, demonstrated higher photocatalytic activity than the pure TiO2 particles. This enhancement in photocatalytic activity was more significant with AgCl doped TiO2 than that with Ag doped, and more distinct when the degradation was done under visible light than that under UV light.展开更多
The waterborne polyurethane/doped Ti O2 nanoparticle hybrid films were prepared. Nd, I doped Ti O2 was prepared with a 50 nm particle size firstly. The hybrid film was prepared by mixing doped Ti O2 with waterborne po...The waterborne polyurethane/doped Ti O2 nanoparticle hybrid films were prepared. Nd, I doped Ti O2 was prepared with a 50 nm particle size firstly. The hybrid film was prepared by mixing doped Ti O2 with waterborne polyurethane, followed by heat treatment. The presence and nanometric distribution of doped Ti O2 nanoparticles in prepared membranes is evident according to SEM images. The photocatalytic activities of doped Ti O2 were signifi cantly enhanced compared with pure Ti O2 powders. After the hybrid fi lm fabrication, the photocatalytic activities were almost the same as the pure catalysts with kMB of 0.046. In the antibacterial testing, the hybrid fi lms can inhibit E. coli growth. A signifi cant decrease in membrane fl uidity and increase of permeability of E. coli were observed.展开更多
N-doped TiO2 nanocrystals were prepared using titanium alkoxide as precipitant with different proportional materials. The products were characterized by X-ray diffraction, scanning electron microscopy, transmission el...N-doped TiO2 nanocrystals were prepared using titanium alkoxide as precipitant with different proportional materials. The products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and UV-vis diffuse reflectance spectra. It is confirmed experimentally that the photocatalytic activity of N-doped TiO2 is much higher than that of Degussa P25, when used for the degradation of crystal violet. The degradation kinetics follows an apparent first-order reaction, which is consistent with a generally observed Langmuir-Hinshelwood mechanism. The doping of TiO2 with nitrogen significantly increases the absorption in the region of visible light. The energy of the band gap of N-doped TiO2 is 2.92 eV. The better performance of N-doped TiO2 can be explained by the fact that it is also excited with longer-wavelength light.展开更多
A novel method for preparing Ta-doped Ti02 via using Ta2 05 as the doping source is proposed. The preparation process combines the hydrothernlal fluorination of Ta2O5 and the subsequent formation of Ta-doped TiO2 sol....A novel method for preparing Ta-doped Ti02 via using Ta2 05 as the doping source is proposed. The preparation process combines the hydrothernlal fluorination of Ta2O5 and the subsequent formation of Ta-doped TiO2 sol. The results show that the doped sample annealed at 393 K generates an unstable intermediate NH4 TiOF3, which converts into anatase TiO2 with the increase of temperature. After annealing at ≥673K, the Ta-doped TiO2 nanocrystals with the grain size 〈20nm are obtained. Both the XRD and TG-DSC results confirm that Ta doping prevents the anatase-rutile crystal transition of TiO2. The band gap values of the doped samples, as obtained by UV-vis diffuse reflectance spectra, are smaller than that of pure anatase TiO2. The first-principle pseudopotential method calculations indicate that Ta5＋ lies in the TiO2 lattice at the interstitial position.展开更多
FeTi_1-O_2（= 0.00,0.05,0.10） nanocomposites are synthesized using a sol-gel method involving an ethanol solvent in the presence of ethylene glycol as the stabilizer,and acetic acid as the chemical reagent.Their stru...FeTi_1-O_2（= 0.00,0.05,0.10） nanocomposites are synthesized using a sol-gel method involving an ethanol solvent in the presence of ethylene glycol as the stabilizer,and acetic acid as the chemical reagent.Their structural and optical analyses are studied to reveal their physicochemical properties.Using the x-ray diffractometer（XRD）analysis,the size of the nanoparticles（NPs） is found to be 18-32 nm,where the size of the NPs decreases down to 18 nm when Fe impurity of up to 10% is added,whereas their structure remains unchanged.The results also indicate that the structure of the NPs is tetragonal in the anatase phase.The Fourier transform infrared spectroscopy analysis suggests the presence of a vibration bond（Ti-O） in the sample.The photoluminescence analysis indicates that the diffusion of Fe^（3＋） ions into the TiO_2 matrix results in a decreasing electron-hole recombination,and increases the photocatalytic properties,where the best efficiency appears at an impurity of10%.The UV-diffuse reflection spectroscopy analysis indicates that with the elevation of iron impurity,the band gap value decreases from 3.47 eV for the pure sample to 2.95 eV for the 10 mol% Fe-doped TiO_2 NPs.展开更多
In this study, vanadium doped TiO2 thin films were deposited on glass substrates using a sol-gel dip-coating process. X-Ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and UV-Vis spectrophotomete...In this study, vanadium doped TiO2 thin films were deposited on glass substrates using a sol-gel dip-coating process. X-Ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and UV-Vis spectrophotometer were used to characterize the structural, chemical and the optical properties of the thin films. The photo-catalytic activities of films were investigated by methylene blue degradation. Water contact angle on the film surfaces was measured by a water contact angle analyzer. The results indicated that vanadium doping had a significant effect on the self-cleaning properties of TiO2 thin films.展开更多
The nitrogen-doped porous TiO2 layer on Ti6Al4V substrate was fabricated by plasma-based ion implantation of He, O and N. In order to increase the photodegradation efficiency of TiO2 layer, two methods were used in th...The nitrogen-doped porous TiO2 layer on Ti6Al4V substrate was fabricated by plasma-based ion implantation of He, O and N. In order to increase the photodegradation efficiency of TiO2 layer, two methods were used in the process by forming mesopores to increase the specific surface area and by nitrogen doping to increase visible light absorption. Importantly, TiO2 formation, porosity architectures and nitrogen doping can be performed by implantation of He, O and N in one step. After implantation, annealing at 650 ℃ leads to a mixing phase of anatase with a little rutile in the implanted layer. By removing the near surface compact layer using argon ion sputtering, the meso-porous structure was exposed on surfaces. Nitrogen doping enlarges the photo-response region of visible light. Moreover, the nitrogen dose of 8×1015 ion/cm2 induces a stronger visible light absorption. The photodegradation of rhodamine B solution with visible light sources indicates that the mesopores on surfaces and nitrogen doping contribute to an apparent increase of photocatalysis efficiency.展开更多
Capacity of the silver-doped TiO2 under UV-C light to restrain cyanobacterial growth was explored with Anabaena sp. PCC 7120 and Microcystis aeruginosa as test species. The survival, chlorophyll bleaching, photosynthe...Capacity of the silver-doped TiO2 under UV-C light to restrain cyanobacterial growth was explored with Anabaena sp. PCC 7120 and Microcystis aeruginosa as test species. The survival, chlorophyll bleaching, photosynthetic activity, DNA breakages, antioxidant enzyme activities, lipid peroxidation, and cellular morphologic structure of test cyanobacteria were analyzed. The results indicate that the test cyanobacteria with UV-C photocatalysis by silver-doped TiO2 sufferd from effects of reactive oxygen species, which promote the damage of the cell wall and the peroxidation of cell membranes, and subsequently, aggravate the losses of cell organelle and viability. The results suggest that UV-C photocatalysis by the silver ions doped TiO2 could be a promising method to prevent fast and excessive growth of cyanobacteria in eutrophic water sources.展开更多
Carbon doped titanium dioxide (C-TiO2) is considered as a promising photocatalytic material due to its optical absorption extended in the visible region compared to pure TiO2. However, in the field of photovoltaic’s,...Carbon doped titanium dioxide (C-TiO2) is considered as a promising photocatalytic material due to its optical absorption extended in the visible region compared to pure TiO2. However, in the field of photovoltaic’s, use of C-doped nano-crystalline titanium dioxide (C-TiO2) electrodes for light absorption has been considered to be unnecessary so far. In this context, we report here on the use of C-TiO2 nano-crystalline electrodes in photochemical solar cells devices (PCSC). Carbon doping has reduced the band gap of TiO2 to 2.41 eV and 2.25 eV with increase in the doping extent for the 9 mM C-TiO2 and 45 mM C-TiO2 respectively. The C-TiO2 electrodes were first used as photo electrodes for solar cells, exhibiting JSC of 1.34651 mA/cm2, VOC 0.683 V, FF 50.23% and η 0.46%. for the 9 mM C-TiO2 and exhibiting JSC of 1.34651 mA/cm2, VOC 0.815 V, FF 54.3% and η 0.59% for the 45 mM C-TiO2. The fabricated solar cell devices have shown an increase in VOC of up to 0.815 V, which is higher than that of 0.7 V for dye sensitized solar cells. The doping of carbon in TiO2 lattice was closely studied by SEM, XRD, RS and UV-Vis spectroscopy.展开更多
基金Project(2010CB631001)supported by the National Basic Research Program of ChinaProject(50871046)supported by the National Natural Science Foundation of China
文摘Cu-doped TiO2 nanoparticles with different doping contents from 0 to 2.0% （mole fraction） were synthesized through sol-gel method. X-ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS） and field emission scanning electron microscope （FE-SEM） were used to characterize the crystalline structure, chemical valence states and morphology of TiO2 nanoparticles. UV-Vis absorption spectrum was used to measure the optical absorption property of the samples. The photocatalytic performance of the samples was characterized by degrading 20 mg/L methyl orange under UV-Vis irradiation. The results show that the Cu-doped TiO2 nanoparticles exhibit a significant increase in photocatalytic performance over the pure TiO2 nanoparticles, and the TiO2 nanoparticles doped with 1.0% Cu show the best photocatalytic performance. The improvement in photocatalytic performance is attributed to the enhanced light adsorption in UV-Vis range and the decrease of the recombination rate of photoinduced electron-hole oair of the Cu-doped TiO2 nanoparticles.
文摘Cerium-doped titanium dioxide nano-powders were prepared through the sol-gel method and the compound sampies were characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM）, and UV/Vis diffuse reflectance spectra （DRS）. The photocatalytic activity was evaluated by photocatalytic degradation of phenol in water. The results of XRD, TEM, and DRS show that pure TiO2 and Ce-doped TiO2 powder crystallines are a mixture of anatase and rutile ; the doping can retard the development of the grain size of TiO2 and decrease the diameter of TiO2 from more than 20 nm of pure TiO2 to about 10 nm; the doped TiO2 can improve the light absorption of TiO2 and suitable doping content tends to move the DRS spectrum of TiO2 towards visible light, but too much doping is not good for the light absorption ability. The results of the photocatalytic experiments show that doping with Ce content of 0.08% -0.4% can increase the photocatalytic activity of TiO2; however, doping with Ce content of 0.5% -2.5% can significantly decrease the photocatalytic activity of TiO2. The favorite doping content is 0.4% in the range of our experiments.
文摘A carbon‐doped TiO2/fly ash support(C‐TiO2/FAS)composite photocatalyst was successfully synthesized through sol impregnation and subsequent carbonization.The carbon dopants were derived from the organic species generated during the synthesis of the C‐TiO2/FAS composite.A series of analytical techniques,such as scanning electron microscopy(SEM),attenuated total reflection‐Fourier transform infrared(ATR‐FTIR)spectroscopy,X‐ray photoelectron spectroscopy(XPS),and ultraviolet‐visible diffuse reflectance spectroscopy(UV‐Vis DRS),were used to characterize the properties of the prepared samples.The results indicated that C‐TiO2 was successfully coated on the FAS surface.Coupling between C‐TiO2 and FAS resulted in the formation of Si–O–C and Al–O–Ti bonds at their interface.The formation of Si–O–C and Al–O–Ti bonds gave rise to a positive shift of the valence band edge of C‐TiO2 and enhanced its oxidation capability of photogenerated holes as well as photodegradation efficiency of methyl orange.Moreover,the C‐TiO2/FAS photocatalyst exhibited favorable reusability and separability.This work may provide a new route for tuning the electronic band structure of TiO2.
文摘The neutral hydrogen evolution reaction(HER)is vital in the chemical industry,and its efficiency depends on the interior character of the catalyst.Herein,work function(WF)engineering is introduced via 3d metal(Fe,Co,Ni,and Cu)doping for modulating the Fermi energy level of Mo2C.The defective energy level facilitates the free water molecule adsorption and,subsequently,promotes the neutral HER efficiency.Specifically,at a current density of 10 mA/cm2,Cu-Mo2C exhibits the best HER performance with an overpotential of 78 mV,followed by Ni-Mo2C,Co-Mo2C,Fe-Mo2C,and bare Mo2C with 90,95,100,and 173 mV,respectively,and the corresponding Tafel slope values are 40,43,42,56,and 102 mV/dec.The modified WF can also lead to an enhanced photocatalytic efficiency owing to the lowered Schottky barrier and excellent carrier transition across the electrocatalyst–solution interface.When coupling the metal-doped Mo2C samples with TiO2,enhanced photocatalytic neutral HER rates are obtained in comparison to the case with bare TiO2.Typically,the HER rates are 521,404,275,224,147,and 112μmol/h for Cu,Ni,Co,Fe,bare Mo2C,and bare TiO2,respectively.Time-resolved photoluminescence spectroscopy(TRPS)and ultrafast transient absorption(TA)measurements are carried out to confirm the recombination and migration of the photogenerated carriers.The fittedτvalues from the TRPS curves are 22.6,20.5,10.1,4.7,4.0,2.5,and 1.9 ns for TiO2,TiO2-Mo2C,TiO2-Fe-Mo2C,TiO2-Fe-Mo2C,TiO2-Fe-Mo2C,TiO2-Fe-Mo2C,and TiO2-Pt,respectively.Additionally,the fittedτvalues from the TA results are 31,73,and 105 ps for the TiO2-Mo2C,TiO2-Cu-Mo2C,and TiO2-Pt samples,respectively.This work provides in-depth insights into the WF modulation of an electrocatalyst for improving the HER performance.
基金the Nationnal Natural Science Foundation of China (No. 50342016).
文摘Iron（Ⅲ）-doped nanostructure TiO2-coated SiO2 （TiO2/SiO2） particles were prepared using the layer-by-layer assembly technique and their photocatalytic property was studied. TiO2 colloids were synthesized employing the sol-gel method with TiChas a precursor. The samples were characterized by Fourier transform infrared spectroscopy （FTIR）, SEM, EDS, XPS, and XRD. The experimental results show that TiO2 nanopowders on the surface of SiO2 particles are well distributed, the amount of TiO2 is increased with the adding of coating layers, the pure anatase-TiO2 coating layers are synthesized at 500℃, and the photocatalytic activity of Fe^3＋-doped TiO2/SiO2 is higher than that of undoped TiO2/SiO2.
文摘A series of Cr doped TiO2 films were prepared by micro arc oxidation （MAO） using an electrolyte of Na3PO4＋K2Cr2O7. X-ray diffraction and scanning electron microscopy revealed that the films mainly consisted of anatase phase with a porous surface morphology. The films have an excellent photocatalytic effect for degradation of methylene blue and decomposition of water under visible light illumination. This arises from the formation of Cr3＋/Cr4＋ and oxygen vacancy energy levels owing to Cr doping. The former reduces the electron-hole recombination chance, while the latter generates a new gap between the conduction band （CB） and valence band （VB） of TiO2, which lowers the photo energy of the excited electron in the VB to the oxygen vacancy states. The mechanisms for film synthesis during the MAO process are also presented.
文摘Sulfur doped anatase TiO2 nanoparticles （3 nm- 12 nm） were synthesized by the reaction of titanium tetrachloride, water and sulfuric acid with addition of 3 M NaOH at room temperature. The electro-optical and photocatalytic properties of the synthesized sulfur doped TiO2 nanoparticles were studied along with Degussa commercial TiO2 particles （24 nm）. The results show that band gap of TiO2 particles decreases from 3.31 to 3.25 eV and for that of commercial TiO2 to 3.2 eV when the particle sizes increased from 3 nm to 12 nm with increase in sulfur doping. The results of the photocatalytic activity under UV and sun radiation show maximum phenol conversion at the particle size of 4 nm at 4.80% S-doping. Similar results are obtained using UV energy for both phenol conversion and conversion of CO2＋H2O in which formation of methanol, ethanol and proponal is observed. Production of methanol is also achieved on samples with a particle size of 8 and 12 nm and sulfur doping of 4.80% and 5.26%. For TiO2 particle of 4 nm without S doping, the production of methanol, ethanol and proponal was lower as compared to the S-doped particles. This is attributed to the combined electronic effect and band gap change, S dopant, specific surface area and the light source used.
基金supported by the National Natural Science Foundation of China(51368044,51568051,51668046)the National Science Fund for Excellent Young Scholars(51422807)+6 种基金the Science and Technology Supporting Program of Jiangxi Province(20151BBG70018)the Natural Science Foundation of Jiangxi Province for Distinguished Young Scholars(20162BCB23041)the Science Foundation for Young Scientists of Jiangxi Province-Key Project(20171ACB21034)the Science and Technology Project of Jiangxi Provincial Education Department(GJJ160700)the Natural Science Foundation of Jiangxi Province(20161BAB216102)the Jiangxi Province Educational Reform Project(JXJG-16-8-7)the Nanchang Hangkong University Educational Reform Project(JY1604,JY1605,KCPY-1511)~~
文摘Lattice‐doping and surface decoration are prospective routes to improve the visible‐light photocatalytic ability of TiO2,but the two techniques are difficult to combine into one preparation process because they are usually conducted under different conditions,which limits the efficiency of TiO2 modification.In this study,TiO2 was successfully modified by simultaneous lattice‐doping and surface decoration,and the visible‐light photocatalytic capacity was largely improved.Upon comparing the method reported here with previous ones,the most significant difference is that Fe(II)‐phenanthroline was first used as the co‐precursor of the introduced elements of C,N,and Fe.These three elements were simultaneously introduced to TiO2 at high levels by this co‐precursor method.The as‐synthesized photocatalysts were systemically investigated and analyzed by several characterization methods such as XRD,FT‐IR,XPS,Raman spectroscopy,EPR,UV‐Vis DRS,photoluminescence spectra,photocurrent,electrochemical impedance spectra,TEM,and HRTEM.The photocatalytic degradation of 4‐NP under visible‐light irradiation was used to evaluate the photocatalytic activity of the photocatalysts.Based on the experimental data,a probable mechanism for the photocatalytic degradation by the photocatalysts is proposed.This is a novel method of using one source to simultaneously introduce metal and non‐metal elements to TiO2 at high levels,which may provide a new way to prepare highly effective TiO2 photocatalysts.
基金supported by the National Natural Science Foundation of China (Grant No. 51102246)the Knowledge Innovation Program of Institute of Metal Research, Chinese Academy of Sciences (Grant No.Y0N5A111A1)the Youth Innovation Promotion Association, Chinese Academy of Sciences (Grant No.Y2N5711171)
文摘Well crystallized niobium-doped TiO; nanotube arrays （TiNbO-NT） were successfully synthesized via the anodization of titanium/niobium alloy sheets, followed with a heat treatment at 550 ℃ for 2 h. Morphology analysis results demonstrated that both the titanium/niobium alloy microstructure and the dissolution strength of electrolyte played major roles in the formation of nanotube structure. A single-phase microstructure was more favorable to the formation of uniform nanotube arrays, while modulating the dissolution strength of electrolyte was required to obtain nanotube arrays from the alloys with multi-phase microstructures. X-ray diffraction （XRD） and X-ray photoelectron （XPS） analysis results clearly demonstrated that niobium dopants （Nb^5＋） were successfully doped into TiO2 anatase lattice by substituting Ti^4＋ in this approach.
基金This study was supported by the CNPC Research Institute of Safety and Environmental Protection Technology(No.PPCIP2017005).
文摘The hierarchical nanostructured N-doped TiO2 immobilized activated carbon fiber(N-TiO2/ACF)porous composites are fabricated to removal dynamic toluene gas.The results show that nitrogen ions doping and ACF modification can decrease the band gap of TiO2,leading to red shift toward visible light region.Interestingly,N-TiO2/ACF exhibits strongly synergistic effect owing to high surface area,good crystallinity,enhanced bandgap structure and light harvesting.The toluene removal rate of N-TiO2/ACF composites is 2.29 times higher than that of TiO2.The N-TiO2/ACF for toluene degradation followed the Langmuir-Hinshelwood kinetic model,and the rate constant is enhanced 8 times compared with TiO2.The possible photodegradation pathway and mechanisms are proposed.
文摘TiO2 doped with C, N and S (TCNS photocatalyst) was prepared by hydrolysis process using titanium iso-propoxide and thiourea. The prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photo electron spectroscopy (XPS), BET surface area, FTIR and diffuse reflectance spectra (DRS). The results showed that the prepared catalysts are anatase type and nanosized par-ticles. The catalysts exhibited stronger absorption in the visible light region with a red shift in the adsorption edge. The photocatalytic activity of TCNS photocatalysts was evaluated by the photocatalytic degradation of isoproturon pesticide in aqueous solution. In the present study the maximum activity was achieved for TCNS5 catalyst at neutral pH with 1 g L-1 catalyst amount and at 1.14 x 10-4 M concentration of the pesticide solution. The TCNS photocatalysts showed higher phtocatalytic activity under solar light irradiation. This is attributed to the synergetic effects of red shift in the absorption edge, higher surface area and the inhibition of charge carrier recombination process.
文摘Using polystyrene （PSt） particles as template, PSt/TiO2 composite particles with AgCl incorporation were prepared through hydrolysis of tetrabutyl titanate in the presence of AgNO3 and NaCl. AgCl doped TiO2 hollow particles were successfully prepared with the PSt/TiO2 composite microspheres pretreated at 180 ℃ followed by calcination. The morphology of PSt/TiO2 particles and the crystal structures of the AgCl doped TiO2 hollow particles were characterized. The photocatalytic activity of the doped TiO2 hollow particles in degradation of Rhodamine B was tested under UV and visible lights and compared to that with Ag doped TiO2 particles. The results showed that TiO2 hollow particles, either doped with Ag or AgCl, demonstrated higher photocatalytic activity than the pure TiO2 particles. This enhancement in photocatalytic activity was more significant with AgCl doped TiO2 than that with Ag doped, and more distinct when the degradation was done under visible light than that under UV light.
基金Funded by the National Natural Science Foundation of China(No.51208141)Open Project of State Key Laboratory of Urban Water Resource and Environment,Harbin Institute of Technology(No.QA201206)
文摘The waterborne polyurethane/doped Ti O2 nanoparticle hybrid films were prepared. Nd, I doped Ti O2 was prepared with a 50 nm particle size firstly. The hybrid film was prepared by mixing doped Ti O2 with waterborne polyurethane, followed by heat treatment. The presence and nanometric distribution of doped Ti O2 nanoparticles in prepared membranes is evident according to SEM images. The photocatalytic activities of doped Ti O2 were signifi cantly enhanced compared with pure Ti O2 powders. After the hybrid fi lm fabrication, the photocatalytic activities were almost the same as the pure catalysts with kMB of 0.046. In the antibacterial testing, the hybrid fi lms can inhibit E. coli growth. A signifi cant decrease in membrane fl uidity and increase of permeability of E. coli were observed.
基金supported by the Outstanding Adult-Young Scientific Research Encouraging Foundation of Shandong Province (No.2008BS09016)the Nature Science Foundation of Shandong Province (No.Y2007B15)the Scientific Research Program of Shandong Province Education Department, China (No.J06D55)
文摘N-doped TiO2 nanocrystals were prepared using titanium alkoxide as precipitant with different proportional materials. The products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and UV-vis diffuse reflectance spectra. It is confirmed experimentally that the photocatalytic activity of N-doped TiO2 is much higher than that of Degussa P25, when used for the degradation of crystal violet. The degradation kinetics follows an apparent first-order reaction, which is consistent with a generally observed Langmuir-Hinshelwood mechanism. The doping of TiO2 with nitrogen significantly increases the absorption in the region of visible light. The energy of the band gap of N-doped TiO2 is 2.92 eV. The better performance of N-doped TiO2 can be explained by the fact that it is also excited with longer-wavelength light.
基金Supported by the Fundamental Research Funds for the Central Universities under Grant No 2012QNA03
文摘A novel method for preparing Ta-doped Ti02 via using Ta2 05 as the doping source is proposed. The preparation process combines the hydrothernlal fluorination of Ta2O5 and the subsequent formation of Ta-doped TiO2 sol. The results show that the doped sample annealed at 393 K generates an unstable intermediate NH4 TiOF3, which converts into anatase TiO2 with the increase of temperature. After annealing at ≥673K, the Ta-doped TiO2 nanocrystals with the grain size 〈20nm are obtained. Both the XRD and TG-DSC results confirm that Ta doping prevents the anatase-rutile crystal transition of TiO2. The band gap values of the doped samples, as obtained by UV-vis diffuse reflectance spectra, are smaller than that of pure anatase TiO2. The first-principle pseudopotential method calculations indicate that Ta5＋ lies in the TiO2 lattice at the interstitial position.
文摘FeTi_1-O_2（= 0.00,0.05,0.10） nanocomposites are synthesized using a sol-gel method involving an ethanol solvent in the presence of ethylene glycol as the stabilizer,and acetic acid as the chemical reagent.Their structural and optical analyses are studied to reveal their physicochemical properties.Using the x-ray diffractometer（XRD）analysis,the size of the nanoparticles（NPs） is found to be 18-32 nm,where the size of the NPs decreases down to 18 nm when Fe impurity of up to 10% is added,whereas their structure remains unchanged.The results also indicate that the structure of the NPs is tetragonal in the anatase phase.The Fourier transform infrared spectroscopy analysis suggests the presence of a vibration bond（Ti-O） in the sample.The photoluminescence analysis indicates that the diffusion of Fe^（3＋） ions into the TiO_2 matrix results in a decreasing electron-hole recombination,and increases the photocatalytic properties,where the best efficiency appears at an impurity of10%.The UV-diffuse reflection spectroscopy analysis indicates that with the elevation of iron impurity,the band gap value decreases from 3.47 eV for the pure sample to 2.95 eV for the 10 mol% Fe-doped TiO_2 NPs.
文摘In this study, vanadium doped TiO2 thin films were deposited on glass substrates using a sol-gel dip-coating process. X-Ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and UV-Vis spectrophotometer were used to characterize the structural, chemical and the optical properties of the thin films. The photo-catalytic activities of films were investigated by methylene blue degradation. Water contact angle on the film surfaces was measured by a water contact angle analyzer. The results indicated that vanadium doping had a significant effect on the self-cleaning properties of TiO2 thin films.
基金Project(20040213048) supported by the Specialized Research Fund for the Doctoral Program of Higher Education of ChinaProject(20090450737) supported by the China Postdoctoral Science Foundation
文摘The nitrogen-doped porous TiO2 layer on Ti6Al4V substrate was fabricated by plasma-based ion implantation of He, O and N. In order to increase the photodegradation efficiency of TiO2 layer, two methods were used in the process by forming mesopores to increase the specific surface area and by nitrogen doping to increase visible light absorption. Importantly, TiO2 formation, porosity architectures and nitrogen doping can be performed by implantation of He, O and N in one step. After implantation, annealing at 650 ℃ leads to a mixing phase of anatase with a little rutile in the implanted layer. By removing the near surface compact layer using argon ion sputtering, the meso-porous structure was exposed on surfaces. Nitrogen doping enlarges the photo-response region of visible light. Moreover, the nitrogen dose of 8×1015 ion/cm2 induces a stronger visible light absorption. The photodegradation of rhodamine B solution with visible light sources indicates that the mesopores on surfaces and nitrogen doping contribute to an apparent increase of photocatalysis efficiency.
基金Funded by the National Natural Science Foundation of China(No.30540070)the Specialized Research Fund for the Doctoral Program of Higher Education(No.20060487018)
文摘Capacity of the silver-doped TiO2 under UV-C light to restrain cyanobacterial growth was explored with Anabaena sp. PCC 7120 and Microcystis aeruginosa as test species. The survival, chlorophyll bleaching, photosynthetic activity, DNA breakages, antioxidant enzyme activities, lipid peroxidation, and cellular morphologic structure of test cyanobacteria were analyzed. The results indicate that the test cyanobacteria with UV-C photocatalysis by silver-doped TiO2 sufferd from effects of reactive oxygen species, which promote the damage of the cell wall and the peroxidation of cell membranes, and subsequently, aggravate the losses of cell organelle and viability. The results suggest that UV-C photocatalysis by the silver ions doped TiO2 could be a promising method to prevent fast and excessive growth of cyanobacteria in eutrophic water sources.
文摘Carbon doped titanium dioxide (C-TiO2) is considered as a promising photocatalytic material due to its optical absorption extended in the visible region compared to pure TiO2. However, in the field of photovoltaic’s, use of C-doped nano-crystalline titanium dioxide (C-TiO2) electrodes for light absorption has been considered to be unnecessary so far. In this context, we report here on the use of C-TiO2 nano-crystalline electrodes in photochemical solar cells devices (PCSC). Carbon doping has reduced the band gap of TiO2 to 2.41 eV and 2.25 eV with increase in the doping extent for the 9 mM C-TiO2 and 45 mM C-TiO2 respectively. The C-TiO2 electrodes were first used as photo electrodes for solar cells, exhibiting JSC of 1.34651 mA/cm2, VOC 0.683 V, FF 50.23% and η 0.46%. for the 9 mM C-TiO2 and exhibiting JSC of 1.34651 mA/cm2, VOC 0.815 V, FF 54.3% and η 0.59% for the 45 mM C-TiO2. The fabricated solar cell devices have shown an increase in VOC of up to 0.815 V, which is higher than that of 0.7 V for dye sensitized solar cells. The doping of carbon in TiO2 lattice was closely studied by SEM, XRD, RS and UV-Vis spectroscopy.
