Energy resolution calibration is crucial for gamma-ray spectral analysis,as measured using a scintillation detector.A locally constrained regularization method was proposed to determine the resolution calibration para...Energy resolution calibration is crucial for gamma-ray spectral analysis,as measured using a scintillation detector.A locally constrained regularization method was proposed to determine the resolution calibration parameters.First,a Monte Carlo simulation model consistent with an actual measurement system was constructed to obtain the energy deposition distribution in the scintillation crystal.Subsequently,the regularization objective function is established based on weighted least squares and additional constraints.Additional constraints were designed using a special weighting scheme based on the incident gamma-ray energies.Subsequently,an intelligent algorithm was introduced to search for the optimal resolution calibration parameters by minimizing the objective function.The most appropriate regularization parameter was determined through mathematical experiments.When the regularization parameter was 30,the calibrated results exhibited the minimum RMSE.Simulations and test pit experiments were conducted to verify the performance of the proposed method.The simulation results demonstrate that the proposed algorithm can determine resolution calibration parameters more accurately than the traditional weighted least squares,and the test pit experimental results show that the R-squares between the calibrated and measured spectra are larger than 0.99.The accurate resolution calibration parameters determined by the proposed method lay the foundation for gamma-ray spectral processing and simulation benchmarking.展开更多
The three-dimensional spectral analysis method was applied to airglow data from September 2023 to August 2024 derivedfrom an OH airglow imager located at the Hejing station (42.79°N, 83.73°E) to study the pr...The three-dimensional spectral analysis method was applied to airglow data from September 2023 to August 2024 derivedfrom an OH airglow imager located at the Hejing station (42.79°N, 83.73°E) to study the propagation characteristics of gravity waves(GWs) over Northwest China. We found that obvious seasonal variations occur in the propagation of GWs. In spring, GWs mainlypropagate in the northeast direction. In summer and autumn, GWs mainly propagate in the north direction. However, GWs mainlypropagate in the south direction in winter. The direction of GW propagation in the zonal direction is controlled by the wind-filteringeffect, whereas the north–south meridional direction is mainly determined by the location of the wave source. We found that the averageenergy spectrum exhibits a 10%–20% higher intensity in summer and winter compared with spring and autumn. For the first time, wereport the seasonal variation characteristics of GWs over the inland areas of Northwest China, which is of great significance forunderstanding the regional distribution characteristics of GWs.展开更多
As a frequently occurred marine pollution phenomenon,red tides of water body due to eutrophication cause massive mortality of marine organisms and serious ecological problems.The early warning and prediction of red ti...As a frequently occurred marine pollution phenomenon,red tides of water body due to eutrophication cause massive mortality of marine organisms and serious ecological problems.The early warning and prediction of red tide outbreak can provide guidance to the coastal management,and is of great value to the aquaculture industry and marine environment protection.An approach for the risk assessment of red tide occurrence using spectral indices was made.The optimal spectral indices were explored from three candidates,namely two-band ratio(TBR)method,three-band spectral index(TBSI)method,and fluorescence baseline(FLB)method.The correlations between the spectral indices and the red tide occurrence were quantitatively evaluated through analysis of variance(ANOVA).The risk maps for the Beibu Gulf and the Bohai Bay in China were produced with the normalized spectral indices based on the multi-spectral observation from Sentinel-3 satellite.Results show that both TBR and TBSI values have significant correlations with the occurrences of red tide as the ANOVA results.TBSI illustrated correctly the risk of red tide occurrence in the risk maps and was the optimal spectral index offshore risk assessment of red tide.FLB method failed to recognize the high-risk regions and may not be the appropriate spectral index.The risk assessment method proposed in this study can provide early alarms on red tide occurrence and help timely the countermeasure against potential harms.展开更多
β-ray-induced X-ray spectroscopy(BIXS)is a promising technique for tritium analysis that offers several unique advantages,including substantial detection depth,nondestructive testing capabilities,and ease of operatio...β-ray-induced X-ray spectroscopy(BIXS)is a promising technique for tritium analysis that offers several unique advantages,including substantial detection depth,nondestructive testing capabilities,and ease of operation.For thin solid tritium-containing samples with substrates,the currently used BIXS analysis method can measure the tritium depth profile and content when the sample thickness is known.In this study,a backpropagation(BP)neural network algorithm was used to predict the tritium content and thickness of a thin solid tritium-containing sample with substrates and a uniformly distributed tritium profile.A semi-analytical method was used to generate datasets for training and testing the BP neural network.A dataset ofβ-decay X-ray spectra from 420 tritium-containing zirconium models with different known thicknesses and tritium-tozirconium ratios was used as the input data.The corresponding zirconium thicknesses and tritium-to-zirconium ratios served as the output for training and testing the BP neural network.The mean relative errors(MREs)of the zirconium thickness in the training and test datasets were 0.56%and 0.42%,respectively,whereas the MREs of the tritium-to-zirconium ratio were 0.59%and 0.38%,respectively.Furthermore,the trained BP neural network demonstrates excellent predictive capability across various levels of statistical uncertainty.For the experimentalβ-decay X-ray spectra of two tritium-containing samples,the predicted zirconium thicknesses and tritium-to-zirconium ratios showed good agreement with the results obtained through the elastic backscattering spectrometry(EBS).展开更多
BACKGROUND Although surgery remains the primary treatment for gastric cancer(GC),the identification of effective alternative treatments for individuals for whom surgery is unsuitable holds significance.HER2 overexpres...BACKGROUND Although surgery remains the primary treatment for gastric cancer(GC),the identification of effective alternative treatments for individuals for whom surgery is unsuitable holds significance.HER2 overexpression occurs in approximately 15%-20%of advanced GC cases,directly affecting treatment-related decisions.Spectral-computed tomography(sCT)enables the quantification of material compositions,and sCT iodine concentration parameters have been demonstrated to be useful for the diagnosis of GC and prediction of its invasion depth,angioge-nesis,and response to systemic chemotherapy.No existing report describes the prediction of GC HER2 status through histogram analysis based on sCT iodine maps(IMs).AIM To investigate whether whole-volume histogram analysis of sCT IMs enables the prediction of the GC HER2 status.METHODS This study was performed with data from 101 patients with pathologically confirmed GC who underwent preoperative sCT examinations.Nineteen parameters were extracted via sCT IM histogram analysis:The minimum,maximum,mean,standard deviation,variance,coefficient of variation,skewness,kurtosis,entropy,percentiles(1st,5th,10th,25th,50th,75th,90th,95th,and 99th),and lesion volume.Spearman correlations of the parameters with the HER2 status and clinicopathological parameters were assessed.Receiver operating characteristic curves were used to evaluate the parameters’diagnostic performance.RESULTS Values for the histogram parameters of the maximum,mean,standard deviation,variance,entropy,and percentiles were significantly lower in the HER2+group than in the HER2–group(all P<0.05).The GC differentiation and Lauren classification correlated significantly with the HER2 status of tumor tissue(P=0.001 and 0.023,respectively).The 99th percentile had the largest area under the curve for GC HER2 status identification(0.740),with 76.2%,sensitivity,65.0%specificity,and 67.3%accuracy.All sCT IM histogram parameters correlated positively with the GC HER2 status(r=0.237-0.337,P=0.001-0.017).CONCLUSION Whole-lesion histogram parameters derived from sCT IM analysis,and especially the 99th percentile,can serve as imaging biomarkers of HER2 overexpression in GC.展开更多
Optimization and simplification of optical systems represent a milestone in advancing the development of handheld and portable laser-induced breakdown spectroscopy(LIBS)systems towards smaller,more integrated forms.Th...Optimization and simplification of optical systems represent a milestone in advancing the development of handheld and portable laser-induced breakdown spectroscopy(LIBS)systems towards smaller,more integrated forms.This research,for the first time,conducted a comprehensive optimization design and comparative analysis of three compact LIBS system optical paths:the paraxial optical path(OP),the off-axis OP,and the reflective OP.The differences in spectral intensity and stability among these paths were revealed,providing a scientific basis for selecting the optimal OP for LIBS systems.The research found that the paraxial OP excels in spectral performance and quantitative analysis accuracy,making it the preferred choice for compact LIBS systems.Specifically,the paraxial OP significantly enhances spectral intensity,achieving a 6 times improvement over the off-axis OP and an even more remarkable 150 times increase compared to the reflective OP,greatly enhancing detection sensitivity.Additionally,the relative standard deviation,spectral stability index,maintains a consistently low level,ranging from 10.9%to 13.4%,significantly outperforming the other two OPs and ensuring the reliability of analytical results.In the field of quantitative analysis,the paraxial OP also demonstrates higher accuracy,precision,and sensitivity,comparing to other OPs.The quantitative analysis models for Si,Cu,and Ti elements exhibit excellent fitting,providing users with high-quality quantitative analysis results that are of great significance for applications in material science,environmental monitoring,industrial inspection,and other fields.In summary,this study not only confirms the enormous application potential of the paraxial OP in compact LIBS systems but also provides valuable practical experience and theoretical support for the miniaturization and integration of LIBS systems.Looking ahead,with continuous technological advancements,the design of the paraxial OP is expected to further propel the widespread adoption of LIBS technology in portable,on-site detection applications.展开更多
Pulse echo accumulation is commonly employed in coherent Doppler wind LiDAR(light detection and ranging)under the assumption of steady wind.Here,the measured spectral data are analyzed in the time dimension and freque...Pulse echo accumulation is commonly employed in coherent Doppler wind LiDAR(light detection and ranging)under the assumption of steady wind.Here,the measured spectral data are analyzed in the time dimension and frequency dimension to cope with the temporal wind shear and achieve the optimal accumulation time.A hardware-efficient algorithm combining the interpolation and cross-correlation is used to enhance the wind retrieval accuracy by reducing the frequency sampling interval and then reduce the spectral width calculation error.Moreover,the temporal broadening effect and spatial broadening effect are decoupled according to the strategy we developed.展开更多
In order to overcome the shortcomings that the reconstructed spectral reflectance may be negative when using the classic principal component analysis （PCA）to reduce the dimensions of the multi-spectral data, a nonne...In order to overcome the shortcomings that the reconstructed spectral reflectance may be negative when using the classic principal component analysis （PCA）to reduce the dimensions of the multi-spectral data, a nonnegative constrained principal component analysis method is proposed to construct a low-dimensional multi-spectral space and accomplish the conversion between the new constructed space and the multispectral space. First, the reason behind the negative data is analyzed and a nonnegative constraint is imposed on the classic PCA. Then a set of nonnegative linear independence weight vectors of principal components is obtained, by which a lowdimensional space is constructed. Finally, a nonlinear optimization technique is used to determine the projection vectors of the high-dimensional multi-spectral data in the constructed space. Experimental results show that the proposed method can keep the reconstructed spectral data in [ 0, 1 ]. The precision of the space created by the proposed method is equivalent to or even higher than that by the PCA.展开更多
Synchrotron polychromatic X-ray microdiffraction（micro-XRD） was applied to study in situ deformation twinning of commercially AZ31（Mg-3Al-1Zn） strip subjected to uniaxial tension.The morphology and growth of twins...Synchrotron polychromatic X-ray microdiffraction（micro-XRD） was applied to study in situ deformation twinning of commercially AZ31（Mg-3Al-1Zn） strip subjected to uniaxial tension.The morphology and growth of twins were analyzed in situ under the load level from 64 to 73 MPa.The X-ray microdiffraction data,collected on beamline 12.3.2 at the Advanced Light Source,were then used to map an area of 396μm x 200μm within the region of interest.The experimental set-up and X-ray diffraction microscopy with a depth resolution allow the position and orientation of each illuminated grain to be determined at the submicron size.A list of parent grains sorted by crystallographic orientation were selected to examine their twinning behavior.The results depict twin variant selection,local misorientation fluctuation and mosaic spread for multi-twins within the same parent grain.As load increases,the amplitude of misorientation fluctuation along twin trace keeps increasing.This is attributable to the accumulation of geometrically necessary dislocations.展开更多
Abstract The continuously rotating detonation engine （CRDE） is a new concept of engines for air- craft and spacecraft. Quasi-stable continuously rotating detonation （CRD） can be observed in an annular combustion c...Abstract The continuously rotating detonation engine （CRDE） is a new concept of engines for air- craft and spacecraft. Quasi-stable continuously rotating detonation （CRD） can be observed in an annular combustion chamber, but the sustaining, stabilizing and adjusting mechanisms are not yet clear. To learn more deeply into the CRDE, experimental studies have been carried out to inves- tigate hydrogen-oxygen CRDE. Pressure histories are obtained during each shot, which show that stable CRD waves are generated in the combustor, when feeding pressures are higher than 0.5 MPa for fuel and oxidizer, respectively. Each shot can keep running as long as fresh gas feeding main- tains. Close-up of the pressure history shows the repeatability of pressure peaks and indicates the detonation velocity in hydrogen-oxygen CRD, which proves the success of forming a stable CRD in the annular chamber. Spectrum of the pressure history matches the close-up analysis and confirms the CRD. It also shows multi-wave phenomenon and affirms the fact that in this case a single detonation wave is rotating in the annulus. Moreover, oscillation phenomenon is found in pressure peaks and a self-adjusting mechanism is proposed to explain the phenomenon.展开更多
The spectral methods and ice-induced fatigue analysis are discussed based on Miner＇s linear cumulative fatigue hypothesis and S-N curve data. According to the long-term data of full-scale tests on the platforms in th...The spectral methods and ice-induced fatigue analysis are discussed based on Miner＇s linear cumulative fatigue hypothesis and S-N curve data. According to the long-term data of full-scale tests on the platforms in the Bohai Sea, the ice force spectrum of conical structures and the fatigue environmental model are established. Moreover, the finite element model of JZ20-2MSW platform, an example of ice-induced fatigue analysis, is built with ANSYS software. The mode analysis and dynamic analysis in frequency domain under all kinds of ice fatigue work conditions are carded on, and the fatigue life of the structure is estimated in detail. The methods in this paper can be helpful in ice-induced fatigue analysis of ice-resistant platforms.展开更多
A method was developed for content determination of Na, Mg, A1, Si, P,S, C1, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Ga, Nb, Zr, Y, Sr, Rb, Ba, La and Ce etc. covering 26 major, minor, and trace elements in marine sedim...A method was developed for content determination of Na, Mg, A1, Si, P,S, C1, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Ga, Nb, Zr, Y, Sr, Rb, Ba, La and Ce etc. covering 26 major, minor, and trace elements in marine sediment samples using fused glass disc by X-ray Fluorescence spectrometry. Calibration was made using marine sediment certified reference materials and the synthetic standard samples prepared by mixing several marine sediments with stream sediment and carbonate standard samples in different proportions. The matrix effect was corrected using theoretical alpha coefficients, experience coefficients and the scattered radiation as the internal standard （for the trace elements）. The accuracy of the method was evaluated by analysis of certified reference materials GBW07314, GBW07334 and GSMS6. The results are in good agreement with the certified values of the standards with RSD less than 2.60%, except for Y, Cr, Ga, Ce, La, Nb, Rb, and V with RSD less than 9.0% （n=12）.展开更多
Although laser-induced breakdown spectroscopy(LIBS),as a fast on-line analysis technology,has great potential and competitiveness in the analysis of chemical composition and proximate analysis results of coal in therm...Although laser-induced breakdown spectroscopy(LIBS),as a fast on-line analysis technology,has great potential and competitiveness in the analysis of chemical composition and proximate analysis results of coal in thermal power plants,the measurement repeatability of LIBS needs to be further improved due to the difficulty in controlling the stability of the generated plasmas at present.In this paper,we propose a novel x-ray fluorescence(XRF) assisted LIBS method for high repeatability analysis of coal quality,which not only inherits the ability of LIBS to directly analyze organic elements such as C and H in coal,but also uses XRF to make up for the lack of stability of LIBS in determining other inorganic ash-forming elements.With the combination of elemental lines in LIBS and XRF spectra,the principal component analysis and the partial least squares are used to establish the prediction model and perform multi-elemental and proximate analysis of coal.Quantitative analysis results show that the relative standard deviation(RSD) of C is 0.15%,the RSDs of other elements are less than 4%,and the standard deviations of calorific value,ash content,sulfur content and volatile matter are 0.11 MJ kg,0.17%,0.79% and 0.41%respectively,indicating that the method has good repeatability in determination of coal quality.This work is helpful to accelerate the development of LIBS in the field of rapid measurement of coal entering the power plant and on-line monitoring of coal entering the furnace.展开更多
Response spectral moments are useful for system reliability analysis.Usually,spectral mo- ments are calculated by the frequency domain method.Based on the time domain modal analysis of random vibrations,the authors pr...Response spectral moments are useful for system reliability analysis.Usually,spectral mo- ments are calculated by the frequency domain method.Based on the time domain modal analysis of random vibrations,the authors present a new method for calculating response spectral moments through response correlation functions.The method can be applied to both classical and non-classical damping cases and to three kinds of random excitations,i.e.,white noise,band-limited white noise, and filtered white noise.展开更多
In this paper, we make use of the functional spectral analysis to infer the periodicity of paleoclimate in the Hongzuisi section since about 15 ka. Through combined analysis of organic carbon isotope and CaCO\-3 conte...In this paper, we make use of the functional spectral analysis to infer the periodicity of paleoclimate in the Hongzuisi section since about 15 ka. Through combined analysis of organic carbon isotope and CaCO\-3 content, the law of paleoclimatic evolution of the Hongzuisi section is obtained. There were climatic changes from 10 ka to about 0.1 ka over the last 15 ka. Among these cycles, the cycle of several ka is most remarkable. The result indicates that functional spectral analysis is helpful for paleoclimatic study, which can provide useful information about paleoclimatic reconstruction and future forecast.展开更多
A technique for timescale analysis of spectral lags performed directly in the time domain is developed. Simulation studies are made to compare the time domain technique with the Fourier frequency analysis for spectral...A technique for timescale analysis of spectral lags performed directly in the time domain is developed. Simulation studies are made to compare the time domain technique with the Fourier frequency analysis for spectral time lags. The time domain technique is applied to studying rapid variabilities of X-ray binaries and γ-ray bursts. The results indicate that in comparison with the Fourier analysis the timescale analysis technique is more powerful for the study of spectral lags in rapid variabilities on short time scales and short duration flaring phenomena.展开更多
Fatigue failure has long been an important issue for ships and offshore structures. Among the numerous methods for predicting fatigue life, the spectral method is accepted as the most reliable. Although the theory beh...Fatigue failure has long been an important issue for ships and offshore structures. Among the numerous methods for predicting fatigue life, the spectral method is accepted as the most reliable. Although the theory behind spectral analysis is straight-forward, the analysis itself is complicated and time-consuming because it is closely related to critical technical details such as the application of fatigue loading (wave pressures and the inertial forces due to cargoes), the extraction of the stress, and the calculation of stress RAO. Here, four key technical details-loading application, displacement boundary condition, the calculation of stress RAO, and the extraction of the fatigue stress-are discussed thoroughly. For each aspect, a resolution is presented based on the finite element pre-and post-processing software MSC/PATRAN or FE solver MSC/NASTRAN. The resolutions are effective and efficient, which can help engineers perform spectral fatigue analysis accurately and faster.展开更多
Mineral dissemination and pore space distribution in ore particles are important features that influence heap leaching performance.To quantify the mineral dissemination and pore space distribution of an ore particle,a...Mineral dissemination and pore space distribution in ore particles are important features that influence heap leaching performance.To quantify the mineral dissemination and pore space distribution of an ore particle,a cylindrical copper oxide ore sample(I center dot 4.6 mm x 5.6 mm)was scanned using high-resolution X-ray computed tomography(HRXCT),a nondestructive imaging technology,at a spatial resolution of 4.85 mu m.Combined with three-dimensional(3D)image analysis techniques,the main mineral phases and pore space were segmented and the volume fraction of each phase was calculated.In addition,the mass fraction of each mineral phase was estimated and the result was validated with that obtained using traditional techniques.Furthermore,the pore phase features,including the pore size distribution,pore surface area,pore fractal dimension,pore centerline,and the pore connectivity,were investigated quantitatively.The pore space analysis results indicate that the pore size distribution closely fits a log-normal distribution and that the pore space morphology is complicated,with a large surface area and low connectivity.This study demonstrates that the combination of HRXCT and 3D image analysis is an effective tool for acquiring 3D mineralogical and pore structural data.展开更多
Fourier transform （FF） is a commonly used method in spectral analysis of ocean wave and offshore structure responses, but it is not suitable for records of short length. In this paper another method, wavelet transfo...Fourier transform （FF） is a commonly used method in spectral analysis of ocean wave and offshore structure responses, but it is not suitable for records of short length. In this paper another method, wavelet transform （WT）, is applied to ＇analyze the data of short length. The Morlet wavelet is employed to calculate the spectra density functions for wave records and simulated Floating Production Storage and Offloading （FPSO） vessels＇ responses. Computed wave data include simulated wave data based on JONSWAP spectrum and the recorded data of Storm 149 from North Alwyn. Wavelet method is validated by comparing the statistical characteristics by WF method and those by fast Fourier transform （FFT） method with those of target spectra. The spectral density fnnctions＇ shapes calculated by WT are less malformed and have less error of statistical characteristics compared with those by FT especially when the record lengths decrease.展开更多
The full-spectrum least-squares(FSLS) method is introduced to perform quantitative energy-dispersive X-ray fluorescence analysis for unknown solid samples.Based on the conventional least-squares principle, this spectr...The full-spectrum least-squares(FSLS) method is introduced to perform quantitative energy-dispersive X-ray fluorescence analysis for unknown solid samples.Based on the conventional least-squares principle, this spectrum evaluation method is able to obtain the background-corrected and interference-free net peaks, which is significant for quantization analyses. A variety of analytical parameters and functions to describe the features of the fluorescence spectra of pure elements are used and established, such as the mass absorption coefficient, the Gi factor, and fundamental fluorescence formulas. The FSLS iterative program was compiled in the C language. The content of each component should reach the convergence criterion at the end of the calculations. After a basic theory analysis and experimental preparation, 13 national standard soil samples were detected using a spectrometer to test the feasibility of using the algorithm. The results show that the calculated contents of Ti, Fe, Ni, Cu, and Zn have the same changing tendency as the corresponding standard content in the 13 reference samples. Accuracies of 0.35% and 14.03% are obtained, respectively, for Fe and Ti, whose standard concentrations are 8.82% and 0.578%, respectively. However, the calculated results of trace elements (only tens of lg/g) deviate from the standard values. This may be because of measurement accuracy and mutual effects between the elements.展开更多
基金supported by the National Natural Science Foundation of China(No.41804141)。
文摘Energy resolution calibration is crucial for gamma-ray spectral analysis,as measured using a scintillation detector.A locally constrained regularization method was proposed to determine the resolution calibration parameters.First,a Monte Carlo simulation model consistent with an actual measurement system was constructed to obtain the energy deposition distribution in the scintillation crystal.Subsequently,the regularization objective function is established based on weighted least squares and additional constraints.Additional constraints were designed using a special weighting scheme based on the incident gamma-ray energies.Subsequently,an intelligent algorithm was introduced to search for the optimal resolution calibration parameters by minimizing the objective function.The most appropriate regularization parameter was determined through mathematical experiments.When the regularization parameter was 30,the calibrated results exhibited the minimum RMSE.Simulations and test pit experiments were conducted to verify the performance of the proposed method.The simulation results demonstrate that the proposed algorithm can determine resolution calibration parameters more accurately than the traditional weighted least squares,and the test pit experimental results show that the R-squares between the calibrated and measured spectra are larger than 0.99.The accurate resolution calibration parameters determined by the proposed method lay the foundation for gamma-ray spectral processing and simulation benchmarking.
基金supported by the National Science Foundation of China(Grant Nos.42374205 and 41974179)the Specialized Research Fund of the National Space Science Center,Chinese Academy of Sciences(Grant No.E4PD3010)supported by the Specialized Research Fund for State Key Laboratories.
文摘The three-dimensional spectral analysis method was applied to airglow data from September 2023 to August 2024 derivedfrom an OH airglow imager located at the Hejing station (42.79°N, 83.73°E) to study the propagation characteristics of gravity waves(GWs) over Northwest China. We found that obvious seasonal variations occur in the propagation of GWs. In spring, GWs mainlypropagate in the northeast direction. In summer and autumn, GWs mainly propagate in the north direction. However, GWs mainlypropagate in the south direction in winter. The direction of GW propagation in the zonal direction is controlled by the wind-filteringeffect, whereas the north–south meridional direction is mainly determined by the location of the wave source. We found that the averageenergy spectrum exhibits a 10%–20% higher intensity in summer and winter compared with spring and autumn. For the first time, wereport the seasonal variation characteristics of GWs over the inland areas of Northwest China, which is of great significance forunderstanding the regional distribution characteristics of GWs.
基金Supported by the National Key R&D Program of China(No.2023YFC3108300)the Dalian High-level Talent Innovation Program(No.2022RG02)the Fundamental Research Funds for the Central Universities(No.3132023507)。
文摘As a frequently occurred marine pollution phenomenon,red tides of water body due to eutrophication cause massive mortality of marine organisms and serious ecological problems.The early warning and prediction of red tide outbreak can provide guidance to the coastal management,and is of great value to the aquaculture industry and marine environment protection.An approach for the risk assessment of red tide occurrence using spectral indices was made.The optimal spectral indices were explored from three candidates,namely two-band ratio(TBR)method,three-band spectral index(TBSI)method,and fluorescence baseline(FLB)method.The correlations between the spectral indices and the red tide occurrence were quantitatively evaluated through analysis of variance(ANOVA).The risk maps for the Beibu Gulf and the Bohai Bay in China were produced with the normalized spectral indices based on the multi-spectral observation from Sentinel-3 satellite.Results show that both TBR and TBSI values have significant correlations with the occurrences of red tide as the ANOVA results.TBSI illustrated correctly the risk of red tide occurrence in the risk maps and was the optimal spectral index offshore risk assessment of red tide.FLB method failed to recognize the high-risk regions and may not be the appropriate spectral index.The risk assessment method proposed in this study can provide early alarms on red tide occurrence and help timely the countermeasure against potential harms.
基金supported by the National Natural Science Foundation of China(No.12175158)the Institute of Nuclear Physics and Chemistry,China Academy of Engineering Physics(No.HG2022022)。
文摘β-ray-induced X-ray spectroscopy(BIXS)is a promising technique for tritium analysis that offers several unique advantages,including substantial detection depth,nondestructive testing capabilities,and ease of operation.For thin solid tritium-containing samples with substrates,the currently used BIXS analysis method can measure the tritium depth profile and content when the sample thickness is known.In this study,a backpropagation(BP)neural network algorithm was used to predict the tritium content and thickness of a thin solid tritium-containing sample with substrates and a uniformly distributed tritium profile.A semi-analytical method was used to generate datasets for training and testing the BP neural network.A dataset ofβ-decay X-ray spectra from 420 tritium-containing zirconium models with different known thicknesses and tritium-tozirconium ratios was used as the input data.The corresponding zirconium thicknesses and tritium-to-zirconium ratios served as the output for training and testing the BP neural network.The mean relative errors(MREs)of the zirconium thickness in the training and test datasets were 0.56%and 0.42%,respectively,whereas the MREs of the tritium-to-zirconium ratio were 0.59%and 0.38%,respectively.Furthermore,the trained BP neural network demonstrates excellent predictive capability across various levels of statistical uncertainty.For the experimentalβ-decay X-ray spectra of two tritium-containing samples,the predicted zirconium thicknesses and tritium-to-zirconium ratios showed good agreement with the results obtained through the elastic backscattering spectrometry(EBS).
基金Supported by Science and Technology Program of Fujian Province,No.2021J01430Joint Funds for the Innovation of Science and Technology of Fujian Province,No.2021Y9229.
文摘BACKGROUND Although surgery remains the primary treatment for gastric cancer(GC),the identification of effective alternative treatments for individuals for whom surgery is unsuitable holds significance.HER2 overexpression occurs in approximately 15%-20%of advanced GC cases,directly affecting treatment-related decisions.Spectral-computed tomography(sCT)enables the quantification of material compositions,and sCT iodine concentration parameters have been demonstrated to be useful for the diagnosis of GC and prediction of its invasion depth,angioge-nesis,and response to systemic chemotherapy.No existing report describes the prediction of GC HER2 status through histogram analysis based on sCT iodine maps(IMs).AIM To investigate whether whole-volume histogram analysis of sCT IMs enables the prediction of the GC HER2 status.METHODS This study was performed with data from 101 patients with pathologically confirmed GC who underwent preoperative sCT examinations.Nineteen parameters were extracted via sCT IM histogram analysis:The minimum,maximum,mean,standard deviation,variance,coefficient of variation,skewness,kurtosis,entropy,percentiles(1st,5th,10th,25th,50th,75th,90th,95th,and 99th),and lesion volume.Spearman correlations of the parameters with the HER2 status and clinicopathological parameters were assessed.Receiver operating characteristic curves were used to evaluate the parameters’diagnostic performance.RESULTS Values for the histogram parameters of the maximum,mean,standard deviation,variance,entropy,and percentiles were significantly lower in the HER2+group than in the HER2–group(all P<0.05).The GC differentiation and Lauren classification correlated significantly with the HER2 status of tumor tissue(P=0.001 and 0.023,respectively).The 99th percentile had the largest area under the curve for GC HER2 status identification(0.740),with 76.2%,sensitivity,65.0%specificity,and 67.3%accuracy.All sCT IM histogram parameters correlated positively with the GC HER2 status(r=0.237-0.337,P=0.001-0.017).CONCLUSION Whole-lesion histogram parameters derived from sCT IM analysis,and especially the 99th percentile,can serve as imaging biomarkers of HER2 overexpression in GC.
基金financially supported by National Natural Science Foundation of China (Nos.62305392 and 62305123)Independent Research and Development Project of Naval Engineering University (No.2023504050)the Nursery Plan Project of Navel University of Engineering (2022)。
文摘Optimization and simplification of optical systems represent a milestone in advancing the development of handheld and portable laser-induced breakdown spectroscopy(LIBS)systems towards smaller,more integrated forms.This research,for the first time,conducted a comprehensive optimization design and comparative analysis of three compact LIBS system optical paths:the paraxial optical path(OP),the off-axis OP,and the reflective OP.The differences in spectral intensity and stability among these paths were revealed,providing a scientific basis for selecting the optimal OP for LIBS systems.The research found that the paraxial OP excels in spectral performance and quantitative analysis accuracy,making it the preferred choice for compact LIBS systems.Specifically,the paraxial OP significantly enhances spectral intensity,achieving a 6 times improvement over the off-axis OP and an even more remarkable 150 times increase compared to the reflective OP,greatly enhancing detection sensitivity.Additionally,the relative standard deviation,spectral stability index,maintains a consistently low level,ranging from 10.9%to 13.4%,significantly outperforming the other two OPs and ensuring the reliability of analytical results.In the field of quantitative analysis,the paraxial OP also demonstrates higher accuracy,precision,and sensitivity,comparing to other OPs.The quantitative analysis models for Si,Cu,and Ti elements exhibit excellent fitting,providing users with high-quality quantitative analysis results that are of great significance for applications in material science,environmental monitoring,industrial inspection,and other fields.In summary,this study not only confirms the enormous application potential of the paraxial OP in compact LIBS systems but also provides valuable practical experience and theoretical support for the miniaturization and integration of LIBS systems.Looking ahead,with continuous technological advancements,the design of the paraxial OP is expected to further propel the widespread adoption of LIBS technology in portable,on-site detection applications.
基金Project supported by the Shanghai Science and Technology Innovation Action(Grant No.22dz1208700).
文摘Pulse echo accumulation is commonly employed in coherent Doppler wind LiDAR(light detection and ranging)under the assumption of steady wind.Here,the measured spectral data are analyzed in the time dimension and frequency dimension to cope with the temporal wind shear and achieve the optimal accumulation time.A hardware-efficient algorithm combining the interpolation and cross-correlation is used to enhance the wind retrieval accuracy by reducing the frequency sampling interval and then reduce the spectral width calculation error.Moreover,the temporal broadening effect and spatial broadening effect are decoupled according to the strategy we developed.
基金The Pre-Research Foundation of National Ministries andCommissions (No9140A16050109DZ01)the Scientific Research Program of the Education Department of Shanxi Province (No09JK701)
文摘In order to overcome the shortcomings that the reconstructed spectral reflectance may be negative when using the classic principal component analysis （PCA）to reduce the dimensions of the multi-spectral data, a nonnegative constrained principal component analysis method is proposed to construct a low-dimensional multi-spectral space and accomplish the conversion between the new constructed space and the multispectral space. First, the reason behind the negative data is analyzed and a nonnegative constraint is imposed on the classic PCA. Then a set of nonnegative linear independence weight vectors of principal components is obtained, by which a lowdimensional space is constructed. Finally, a nonlinear optimization technique is used to determine the projection vectors of the high-dimensional multi-spectral data in the constructed space. Experimental results show that the proposed method can keep the reconstructed spectral data in [ 0, 1 ]. The precision of the space created by the proposed method is equivalent to or even higher than that by the PCA.
基金Project(DP140102355)supported by the Australian Research Council(ARC)Project supported by the China Scholarship Council(CSC)
文摘Synchrotron polychromatic X-ray microdiffraction（micro-XRD） was applied to study in situ deformation twinning of commercially AZ31（Mg-3Al-1Zn） strip subjected to uniaxial tension.The morphology and growth of twins were analyzed in situ under the load level from 64 to 73 MPa.The X-ray microdiffraction data,collected on beamline 12.3.2 at the Advanced Light Source,were then used to map an area of 396μm x 200μm within the region of interest.The experimental set-up and X-ray diffraction microscopy with a depth resolution allow the position and orientation of each illuminated grain to be determined at the submicron size.A list of parent grains sorted by crystallographic orientation were selected to examine their twinning behavior.The results depict twin variant selection,local misorientation fluctuation and mosaic spread for multi-twins within the same parent grain.As load increases,the amplitude of misorientation fluctuation along twin trace keeps increasing.This is attributable to the accumulation of geometrically necessary dislocations.
基金supported by the National Natural Science Foundation of China(No.91441110)
文摘Abstract The continuously rotating detonation engine （CRDE） is a new concept of engines for air- craft and spacecraft. Quasi-stable continuously rotating detonation （CRD） can be observed in an annular combustion chamber, but the sustaining, stabilizing and adjusting mechanisms are not yet clear. To learn more deeply into the CRDE, experimental studies have been carried out to inves- tigate hydrogen-oxygen CRDE. Pressure histories are obtained during each shot, which show that stable CRD waves are generated in the combustor, when feeding pressures are higher than 0.5 MPa for fuel and oxidizer, respectively. Each shot can keep running as long as fresh gas feeding main- tains. Close-up of the pressure history shows the repeatability of pressure peaks and indicates the detonation velocity in hydrogen-oxygen CRD, which proves the success of forming a stable CRD in the annular chamber. Spectrum of the pressure history matches the close-up analysis and confirms the CRD. It also shows multi-wave phenomenon and affirms the fact that in this case a single detonation wave is rotating in the annulus. Moreover, oscillation phenomenon is found in pressure peaks and a self-adjusting mechanism is proposed to explain the phenomenon.
基金The paper was supported by the National 863 High Technology Develpoment Plan Project(Grant No.2001AA602015)
文摘The spectral methods and ice-induced fatigue analysis are discussed based on Miner＇s linear cumulative fatigue hypothesis and S-N curve data. According to the long-term data of full-scale tests on the platforms in the Bohai Sea, the ice force spectrum of conical structures and the fatigue environmental model are established. Moreover, the finite element model of JZ20-2MSW platform, an example of ice-induced fatigue analysis, is built with ANSYS software. The mode analysis and dynamic analysis in frequency domain under all kinds of ice fatigue work conditions are carded on, and the fatigue life of the structure is estimated in detail. The methods in this paper can be helpful in ice-induced fatigue analysis of ice-resistant platforms.
基金Supported by China Ministry of Science and Technology (2000DEB20081)China Ocean Mineral Resources R&D Association (COMRA) (No.DY105-05-01-05)+1 种基金China Ministry of Education(No.205089)China National Natural Science Foundation (No.40076015)
文摘A method was developed for content determination of Na, Mg, A1, Si, P,S, C1, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Ga, Nb, Zr, Y, Sr, Rb, Ba, La and Ce etc. covering 26 major, minor, and trace elements in marine sediment samples using fused glass disc by X-ray Fluorescence spectrometry. Calibration was made using marine sediment certified reference materials and the synthetic standard samples prepared by mixing several marine sediments with stream sediment and carbonate standard samples in different proportions. The matrix effect was corrected using theoretical alpha coefficients, experience coefficients and the scattered radiation as the internal standard （for the trace elements）. The accuracy of the method was evaluated by analysis of certified reference materials GBW07314, GBW07334 and GSMS6. The results are in good agreement with the certified values of the standards with RSD less than 2.60%, except for Y, Cr, Ga, Ce, La, Nb, Rb, and V with RSD less than 9.0% （n=12）.
基金supported by National Energy R&D Center of Petroleum Refining Technology of China(RIPP,SINOPEC)National Key Research and Development Program of China(No.2017YFA0304203)+5 种基金Changjiang Scholars and Innovative Research Team in University of Ministry of Education of China(No.IRT_17R70)National Natural Science Foundation of China(Nos.61975103,61875108,61775125 and 11434007)Industrial Application Innovation Project(No.627010407)Scientific and Technological Innovation Project of Shanxi Gemeng US-China Clean Energy R&D Center Co.,Ltd111 Project(D18001)Fund for Shanxi‘1331KSC’。
文摘Although laser-induced breakdown spectroscopy(LIBS),as a fast on-line analysis technology,has great potential and competitiveness in the analysis of chemical composition and proximate analysis results of coal in thermal power plants,the measurement repeatability of LIBS needs to be further improved due to the difficulty in controlling the stability of the generated plasmas at present.In this paper,we propose a novel x-ray fluorescence(XRF) assisted LIBS method for high repeatability analysis of coal quality,which not only inherits the ability of LIBS to directly analyze organic elements such as C and H in coal,but also uses XRF to make up for the lack of stability of LIBS in determining other inorganic ash-forming elements.With the combination of elemental lines in LIBS and XRF spectra,the principal component analysis and the partial least squares are used to establish the prediction model and perform multi-elemental and proximate analysis of coal.Quantitative analysis results show that the relative standard deviation(RSD) of C is 0.15%,the RSDs of other elements are less than 4%,and the standard deviations of calorific value,ash content,sulfur content and volatile matter are 0.11 MJ kg,0.17%,0.79% and 0.41%respectively,indicating that the method has good repeatability in determination of coal quality.This work is helpful to accelerate the development of LIBS in the field of rapid measurement of coal entering the power plant and on-line monitoring of coal entering the furnace.
基金Project supported by the National Natural Science Foundation of China.
文摘Response spectral moments are useful for system reliability analysis.Usually,spectral mo- ments are calculated by the frequency domain method.Based on the time domain modal analysis of random vibrations,the authors present a new method for calculating response spectral moments through response correlation functions.The method can be applied to both classical and non-classical damping cases and to three kinds of random excitations,i.e.,white noise,band-limited white noise, and filtered white noise.
基金GrantedbytheNationalNaturalScienceFoundationofChina (No .4 9972 0 5 7)
文摘In this paper, we make use of the functional spectral analysis to infer the periodicity of paleoclimate in the Hongzuisi section since about 15 ka. Through combined analysis of organic carbon isotope and CaCO\-3 content, the law of paleoclimatic evolution of the Hongzuisi section is obtained. There were climatic changes from 10 ka to about 0.1 ka over the last 15 ka. Among these cycles, the cycle of several ka is most remarkable. The result indicates that functional spectral analysis is helpful for paleoclimatic study, which can provide useful information about paleoclimatic reconstruction and future forecast.
基金the National Natural Science Foundation of China.
文摘A technique for timescale analysis of spectral lags performed directly in the time domain is developed. Simulation studies are made to compare the time domain technique with the Fourier frequency analysis for spectral time lags. The time domain technique is applied to studying rapid variabilities of X-ray binaries and γ-ray bursts. The results indicate that in comparison with the Fourier analysis the timescale analysis technique is more powerful for the study of spectral lags in rapid variabilities on short time scales and short duration flaring phenomena.
文摘Fatigue failure has long been an important issue for ships and offshore structures. Among the numerous methods for predicting fatigue life, the spectral method is accepted as the most reliable. Although the theory behind spectral analysis is straight-forward, the analysis itself is complicated and time-consuming because it is closely related to critical technical details such as the application of fatigue loading (wave pressures and the inertial forces due to cargoes), the extraction of the stress, and the calculation of stress RAO. Here, four key technical details-loading application, displacement boundary condition, the calculation of stress RAO, and the extraction of the fatigue stress-are discussed thoroughly. For each aspect, a resolution is presented based on the finite element pre-and post-processing software MSC/PATRAN or FE solver MSC/NASTRAN. The resolutions are effective and efficient, which can help engineers perform spectral fatigue analysis accurately and faster.
基金financially supported by the National Natural Science Foundation of China(No.51304076)the Natural Science Foundation of Hunan Province,China(No.14JJ4064)
文摘Mineral dissemination and pore space distribution in ore particles are important features that influence heap leaching performance.To quantify the mineral dissemination and pore space distribution of an ore particle,a cylindrical copper oxide ore sample(I center dot 4.6 mm x 5.6 mm)was scanned using high-resolution X-ray computed tomography(HRXCT),a nondestructive imaging technology,at a spatial resolution of 4.85 mu m.Combined with three-dimensional(3D)image analysis techniques,the main mineral phases and pore space were segmented and the volume fraction of each phase was calculated.In addition,the mass fraction of each mineral phase was estimated and the result was validated with that obtained using traditional techniques.Furthermore,the pore phase features,including the pore size distribution,pore surface area,pore fractal dimension,pore centerline,and the pore connectivity,were investigated quantitatively.The pore space analysis results indicate that the pore size distribution closely fits a log-normal distribution and that the pore space morphology is complicated,with a large surface area and low connectivity.This study demonstrates that the combination of HRXCT and 3D image analysis is an effective tool for acquiring 3D mineralogical and pore structural data.
文摘Fourier transform （FF） is a commonly used method in spectral analysis of ocean wave and offshore structure responses, but it is not suitable for records of short length. In this paper another method, wavelet transform （WT）, is applied to ＇analyze the data of short length. The Morlet wavelet is employed to calculate the spectra density functions for wave records and simulated Floating Production Storage and Offloading （FPSO） vessels＇ responses. Computed wave data include simulated wave data based on JONSWAP spectrum and the recorded data of Storm 149 from North Alwyn. Wavelet method is validated by comparing the statistical characteristics by WF method and those by fast Fourier transform （FFT） method with those of target spectra. The spectral density fnnctions＇ shapes calculated by WT are less malformed and have less error of statistical characteristics compared with those by FT especially when the record lengths decrease.
基金supported by the National Key R&D Project of China(No.2017YFC0602100)the National Natural Science Foundation of China(No.41774147)Sichuan Science and Technology Support Program(No.2015GZ0272)
文摘The full-spectrum least-squares(FSLS) method is introduced to perform quantitative energy-dispersive X-ray fluorescence analysis for unknown solid samples.Based on the conventional least-squares principle, this spectrum evaluation method is able to obtain the background-corrected and interference-free net peaks, which is significant for quantization analyses. A variety of analytical parameters and functions to describe the features of the fluorescence spectra of pure elements are used and established, such as the mass absorption coefficient, the Gi factor, and fundamental fluorescence formulas. The FSLS iterative program was compiled in the C language. The content of each component should reach the convergence criterion at the end of the calculations. After a basic theory analysis and experimental preparation, 13 national standard soil samples were detected using a spectrometer to test the feasibility of using the algorithm. The results show that the calculated contents of Ti, Fe, Ni, Cu, and Zn have the same changing tendency as the corresponding standard content in the 13 reference samples. Accuracies of 0.35% and 14.03% are obtained, respectively, for Fe and Ti, whose standard concentrations are 8.82% and 0.578%, respectively. However, the calculated results of trace elements (only tens of lg/g) deviate from the standard values. This may be because of measurement accuracy and mutual effects between the elements.
