To reduce the temperature diseases of asphalt pavement,improve the service quality of road and extend service life,the research of inorganic powders that reduce the temperature of asphalt pavements was systematically ...To reduce the temperature diseases of asphalt pavement,improve the service quality of road and extend service life,the research of inorganic powders that reduce the temperature of asphalt pavements was systematically sorted out.The common types,physicochemical properties and application methods of inorganic powders were defined.The road performances of modified asphalt and its mixture were evaluated.The modification mechanism of inorganic powders in asphalt was analyzed.On this basis,the cooling effect and cooling mechanism of inorganic powders was revealed.The results indicate that inorganic powders are classified into hollow,porous,and energy conversion types.The high-temperature performance of inorganic powders modified asphalt and its mixture is significantly improved,while there is no significant change in low-temperature performance and water stability.The average increase in rutting resistance factor(G*/sin(δ))and dynamic stability is 40%–72%and 30%–50%,respectively.The modification mechanism of inorganic powders in asphalt is physical blending.The thermal conductivity of hollow and porous inorganic powders modified asphalt mixture decreases by 30.05%and 43.14%,respectively.The temperature of hollow,porous and energy conversion inorganic powders modified asphalt mixture at 5 cm decreases by 2.3 ℃–3.5 ℃,0.8 ℃–3.7 ℃and 4.1 ℃–4.7℃,respectively.Hollow and porous inorganic powders block heat conduction,while energy conversion inorganic powders achieve cooling through their functional properties.展开更多
Silicon nanowires(SiNWs)have been used in a wide variety of applications over the past few decades due to their excellent material properties.The only drawback is the high production cost of SiNWs.The preparation of S...Silicon nanowires(SiNWs)have been used in a wide variety of applications over the past few decades due to their excellent material properties.The only drawback is the high production cost of SiNWs.The preparation of SiNWs from photovoltaic waste silicon(WSi)powders,which are high-volume industrial wastes,not only avoids the secondary energy consumption and environmental pollution caused by complicated recycling methods,but also realizes its high-value utilization.Herein,we present a method to rapidly convert photovoltaic WSi powders into SiNWs products.The flash heating and quenching provided by carbothermal shock induce the production of free silicon atoms from the WSi powders,which are rapidly reorganized and assembled into SiNWs during the vapor-phase process.This method allows for the one-step composite of SiNWs and carbon cloth(CC)and the formation of SiC at the interface of the silicon(Si)and carbon(C)contact to create a stable chemical connection.The obtained SiNWs-CC(SiNWs@CC)composites can be directly used as lithium anodes,exhibiting high initial coulombic efficiency(86.4%)and stable cycling specific capacity(2437.4 mA h g^(-1)at 0.5 A g^(-1)after 165 cycles).In addition,various SiNWs@C composite electrodes are easily prepared using this method.展开更多
Magnetostrictive Fe-Ga alloys have captivated substantial focus in biomedical applications because of their exceptional transition efficiency and favorable cytocompatibility.Nevertheless,Fe-Ga alloys always exhibit fr...Magnetostrictive Fe-Ga alloys have captivated substantial focus in biomedical applications because of their exceptional transition efficiency and favorable cytocompatibility.Nevertheless,Fe-Ga alloys always exhibit frustrating magnetostriction coefficients when presented in bulk dimensions.It is well-established that the magnetostrictive performance of Fe-Ga alloys is intimately linked to their phase and crystal structures.In this study,various concentrations of boron(B)were doped into Fe_(81)Ga_(19) alloys via the laser-beam powder bed fusion(LPBF)technique to tailor the crystal and phase structures,thereby improving the magnetostrictive performance.The results revealed the capacity for quick solidification of the LPBF process in expediting the solid solution of B element,which increased both lattice distortion and dislocations within the Fe-Ga matrix.These factors contributed to an elevation in the density of the modified-D0_(3) phase structure.Moreover,the prepared Fe-Ga-B alloys also exhibited a(001)preferred grain orientation caused by the high thermal gradients during the LPBF process.As a result,a maximum magnetostriction coefficient of 105 ppm was achieved in the(Fe_(81)Ga_(19))_(98.5)B_(1.5) alloy.In alternating magnetic fields,all the LPBF-prepared alloys showed good dynamic magnetostriction response without visible hysteresis,while the(Fe_(81)Ga_(19))_(98.5)B_(1.5) alloy presented a notable enhancement of~30%in magnetostriction coefficient when compared with the Fe_(81)Ga_(19) alloy.Moreover.the(Fe_(81)Ga_(19))_(98.5)B_(1.5) alloy exhibited favorable biocompatibility and osteogenesis,as confirmed by increased alkaline phosphatase(ALP)activity and the formation of mineralized nodules.These findings suggest that the B-doped Fe-Ga alloys combined with the LPBF technique hold promise for the development of bulk magnetostrictive alloys that are applicable for bone repair applications.展开更多
Laser additively manufactured(LAM)Ni-based superalloys commonly exhibit low strength and high residual stress in the as-built state,requiring post-heat treatment to improve mechanical properties.We propose a modified ...Laser additively manufactured(LAM)Ni-based superalloys commonly exhibit low strength and high residual stress in the as-built state,requiring post-heat treatment to improve mechanical properties.We propose a modified heat treatment(MHT)process that only involves a single-step aging at 650℃ for 4 h to achieve high strength,high ductility,and low residual stress simultaneously in a laser powder bed fusion(LPBF)-processed Inconel 718(IN718)alloy.The MHT treated alloy exhibits comparable tensile strength(1368 MPa)to the conventional solution plus two-step aging(SA)treated alloy(1398 MPa),while the tensile elongation(∼21.7%for MHT treated alloy and 13.4%for SA treated alloy)is 60%higher and the residual stress(∼195 MPa)is 20%lower than the SA treated alloy.The balanced high performance of the MHT IN718 alloy was mainly attributed to the precipitation of abundantγ’’phase with a size of∼5 nm,while the original nano-sized Laves precipitates and dislocation cells were mostly retained.The finer size and higher fraction ofγ”of the MHT sample mainly result from the dislocation structure and compositional variations in the as-built IN718,which promotes precipitation during aging.The retention of Laves phase,and cellular dislocation network in the MHT alloy also contributes to work hardening during tension and suspends the occurrence of necking.This study unveils a unique strengthening and toughening mechanism in the Ni-based superalloy produced by LAM with the presence of abundant Laves precipitates and provides a simple,low energy-consumption and cost-effective heat treatment route for achieving desirable mechanical properties.展开更多
This work investigated the anisotropy tensile properties of Inconel 625 alloy fabricated by laser powder bed fusion (LPBF) under various tests temperature, focusing the anisotropy evolution during the high temperature...This work investigated the anisotropy tensile properties of Inconel 625 alloy fabricated by laser powder bed fusion (LPBF) under various tests temperature, focusing the anisotropy evolution during the high temperature. The microstructure contained columnar grains with (111) texture in the vertical plane (90° sample), while a large equiaxed grain with (100) texture was produced in the horizontal plane (0° sample). As for 45° sample, a large number of equiaxed grains and a few columnar grains with (111) texture can be observed. The sample produced at a 0° orientation demonstrates the highest tensile strength, whereas the 90° sample exhibits the greatest elongation. Conversely, the 45° sample displays the least favorable overall performance. As the tests temperature increased from room temperature to 600℃, the anisotropy rate of ultimate tensile strength, yield strength and ductility between 0° and 45° samples, decreased from 8.98 to 6.96%, 2.36 to 1.28%, 19.93 to 12.23%, as well as between 0° and 90° samples decreased from 4.87 to 4.03%, 11.88 to 7.21% and 14.11 to 6.89%, respectively, because of the recovery of oriented columnar grains.展开更多
BACKGROUND Ulcerative colitis(UC)is a chronic inflammatory disease affecting the colon.The most common psychological issue in UC patients is varying degrees of depre-ssion,which affects the condition and quality of li...BACKGROUND Ulcerative colitis(UC)is a chronic inflammatory disease affecting the colon.The most common psychological issue in UC patients is varying degrees of depre-ssion,which affects the condition and quality of life of UC patients and may lead to deterioration of the patient’s condition.UC drugs combined with anti-anxiety and antidepression drugs can alleviate symptoms of both depression and UC.Brain-derived neurotrophic factor(BDNF)precursor(proBDNF)/p75 neurotrophin receptor(p75NTR)/sortilin and BDNF/tropomyosin receptor kinase B(TrkB)signalling balance is essential for maintaining brain homeostasis and preventing the development of depressive behaviours.AIM To explore the mechanism by which Wuling powder regulates the proBDNF/p75NTR/sortilin and BDNF/TrkB pathways in the treatment of UC with depre-ssion.METHODS Depression was established in C57BL/6J mice via chronic restraint stress,and the UC model was induced with dextran sodium sulfate(DSS).In the treatment stage,mesalazine(MS)was the basic treatment,Wuling powder was the experimental treatment,and fluoxetine was the positive control drug for treating depression.Changes in intestinal mucosal inflammation,behaviour,and the proBDNFp75NTR/sortilin and BDNF/TrkB pathways were evaluated.RESULTS In the depression groups,Wuling powder decreased the immobility time,increased the distance travelled in the central zone and the total distance travelled,and restored balance in the proBDNF/p75NTR/sortilin and BDNF/TrkB signalling pathways.In the DSS and chronic restraint stress+DSS groups,immobility time increased,distance travelled in the central zone and total distance travelled decreased,activity of the proBDNF/p75NTR/sortilin pathway was upregulated,and activity of the BDNF/TrkB pathway was downregulated,indicating that mice with UC often have comorbid depression.Compared with those of MS alone,Wuling powder combined with MS further decreased the colon histopathological scores and the expression levels of tumor necrosis factor-alpha and interleukin-6 mRNAs.CONCLUSION This study confirmed that Wuling powder may play an antidepressant role by regulating the balance of the proBDNF/p75NTR/sortilin and BDNF/TrkB signalling pathways and further relieve intestinal inflammation in UC.展开更多
In order to achieve the large-scale application of manufactured sand in railway high-strength concrete structure,a series of high-strength manufactured sand concrete(HMC)are prepared by taking the manufactured sand li...In order to achieve the large-scale application of manufactured sand in railway high-strength concrete structure,a series of high-strength manufactured sand concrete(HMC)are prepared by taking the manufactured sand lithology(tuff,limestone,basalt,granite),stone powder content(0,5%,10%,15%)and concrete strength grade(C60,C80,C100)as variables.The evolution of mechanical properties of HMC and the correlation between cubic compressive strength and other mechanical properties are studied.Compared to river sand,manufactured sand enhances the cubic compressive strength,axial compressive strength and elastic modulus of concrete,while its potential microcracks weaken the flexural strength and splitting tensile strength of concrete.Stone powder content displays both positive and negative effects on mechanical properties of HMC,and the stone powder content is suggested to be less than 10%.The empirical formulas between cubic compressive strength and other mechanical properties are proposed.展开更多
The feasibility of manufacturing Ti-6Al-4V samples through a combination of laser-aided additive manufacturing with powder(LAAM_(p))and wire(LAAM_(w))was explored.A process study was first conducted to successfully ci...The feasibility of manufacturing Ti-6Al-4V samples through a combination of laser-aided additive manufacturing with powder(LAAM_(p))and wire(LAAM_(w))was explored.A process study was first conducted to successfully circumvent defects in Ti-6Al-4V deposits for LAAM_(p) and LAAM_(w),respectively.With the optimized process parameters,robust interfaces were achieved between powder/wire deposits and the forged substrate,as well as between powder and wire deposits.Microstructure characterization results revealed the epitaxial prior β grains in the deposited Ti-6Al-4V,wherein the powder deposit was dominated by a finerα′microstructure and the wire deposit was characterized by lamellar α phases.The mechanisms of microstructure formation and correlation with mechanical behavior were analyzed and discussed.The mechanical properties of the interfacial samples can meet the requirements of the relevant Aerospace Material Specifications(AMS 6932)even without post heat treatment.No fracture occurred within the interfacial area,further suggesting the robust interface.The findings of this study highlighted the feasibility of combining LAAM_(p) and LAAM_(w) in the direct manufacturing of Ti-6Al-4V parts in accordance with the required dimensional resolution and deposition rate,together with sound strength and ductility balance in the as-built condition.展开更多
Additive manufacturing (AM) of high-strength metallic alloys frequently encounters detrimental distortion and cracking, attributed to the accumulation of thermal stresses. These issues significantly impede the practic...Additive manufacturing (AM) of high-strength metallic alloys frequently encounters detrimental distortion and cracking, attributed to the accumulation of thermal stresses. These issues significantly impede the practical application of as-printed components. This study examines the Mg-15Gd-1Zn-0.4Zr (GZ151K, wt.%) alloy, a prototypical high-strength casting Mg-RE alloy, fabricated through laser powder bed fusion (LPBF). Despite achieving ultra-high strength, the GZ151K alloy concurrently exhibits a pronounced cold-cracking susceptibility. The as-printed GZ151K alloy consists of almost fully fine equiaxed grains with an average grain size of merely 2.87 µm. Subsequent direct aging (T5) heat treatment induces the formation of dense prismatic β' precipitates. Consequently, the LPBF-T5 GZ151K alloy manifests an ultra-high yield strength of 405 MPa, surpassing all previously reported yield strengths for Mg alloys fabricated via LPBF and even exceeding that of its extrusion-T5 counterpart. Interestingly, as-printed GZ151K samples with a build height of 2 mm exhibit no cracking, whereas samples with build heights ranging from 4 to 18 mm demonstrate severe cold cracking. Thermal stress simulation also suggests that the cold cracking susceptibility increases significantly with increasing build height. The combination of high thermal stress and low ductility in the as-printed GZ151K alloy culminates in a high cold cracking susceptibility. This study offers novel insights into the intricate issue of cold cracking in the LPBF process of high-strength Mg alloys, highlighting the critical balance between achieving high strength and mitigating cold cracking susceptibility.展开更多
Introduction The widespread use of cement in concrete leads to increased carbon emissions,so the demand for supplementary cementitious materials increases significantly.Limestone powder and steel slag powder are widel...Introduction The widespread use of cement in concrete leads to increased carbon emissions,so the demand for supplementary cementitious materials increases significantly.Limestone powder and steel slag powder are widely used as supplementary cementitious materials in modern concrete.However,for UHPC and self-compacting concrete,an extremely low water/binder(W/B)ratio is on one hand a key factor in achieving ultra-high strength and ultra-low porosity of the materials,on the other hand,also leads to the deterioration of the rheological properties of the fresh paste.Meanwhile,the existing researches focus on the influence of single limestone powder or steel slag powder on the mechanical properties or microstructure of cement-based materials.Little work on the influence of steel slag powder or limestone powder on the rheological properties of composite paste at an extremely low water/binder ratio has been investigated quantitatively.The mechanism of the effect of steel slag powder or limestone powder on the rheological properties of composite paste at extremely low water/binder ratios is still unclear.In this work,the effects of steel slag powder and limestone powder on the rheological properties of composite paste at different low water/binder ratios were analyzed via determining the flow diameter,setting time,marsh cone flow time,rheological parameters,and total organic carbon content.Methods A composite paste was prepared with P.I 42.5 ordinary Portland cement,steel slag powder,limestone powder,blast furnace slag and silica fume as raw materials in a certain proportion.To achieve the preparation of composite paste with extremely low water/binder ratios,a polycarboxylate superplasticizer with a water/reducing rate of 40%(Jiangsu Subot New Materials Co.,Ltd.,China)was used.The dosage of polycarboxylate superplasticizer for the composite paste with different water/binder ratios of 0.16 and 0.21 was 2%and 0.8%,respectively.Composite pastes with different proportions of steel slag powder or limestone powder at water/binder ratios of 0.16 and 0.21 were prepared.The flow diameter(i.e.,the larger the flow diameter,the better the fluidity),setting time(i.e.,the time when the fluidity is lost)and marsh cone flow time(i.e.,the shorter the flow time,the better the fluidity)were determined to analyze the fluidity of the composite pastes.the rheological properties of composite paste at a water/binder ratio of 0.16 for rheological properties tests were determined,and the rheological parameters were obtained by the H-B model.The adsorption performance of the polycarboxylate superplasticizer was analyzed by testing the TOC content.Results and discussion When the ratio of water/binder is 0.16,both limestone powder and steel slag powder initially increase the flow diameter of the composite paste.However,the fluidity of the composite paste decreases over time,and the reduction is more pronounced with steel slag powder.This is because the nucleation and hydration promotion effect of limestone powder can reduce the loss rate of flow diameter,while the rough particles of steel slag powder increase the internal friction force,resulting in a decrease in the flow diameter of composite paste.Adding limestone powder and steel slag powder both shortens the setting time and marsh cone flow time of the composite paste.However,the steel slag powder addition of 30%delays the final setting time due to its delaying effect.Also,limestone powder can enhance the thixotropy and reduce the yield stress and plastic viscosity,thereby improving the rheological properties.In contrast,steel slag powder can increase the yield stress and plastic viscosity,thereby weakening the rheological properties and thixotropy.Steel slag powder and limestone powder both can enhance the adsorption effect of polycarboxylate superplasticizer.Steel slag powder has a stronger adsorption effect.The composite paste containing limestone powder has a higher free water content.This is because the rough and porous surface of steel slag itself and the uneven particle shape lead to the physical adsorption of polycarboxylate superplasticizer molecules on the surface of steel slag particles,thereby reducing the effective content of the water reducer dispersion.Increasing the water/binder ratio to 0.21 results in a decrease in the flow diameter of the composite paste.Furthermore,the setting time and marsh cone flow time can prolong due to the reduction in the dosage of polycarboxylate superplasticizer.Conclusions The results showed that the fluidity loss rate of composite paste with limestone powder could be lower than that of composite paste with steel slag powder.Compared to steel slag powder,the addition of limestone powder reduced the setting time and marsh cone flow time of the composite paste.The addition of limestone powder could shorten the yield stress and plastic viscosity of the composite paste.Therefore,the composite paste with limestone powder had better rheological properties and stronger thixotropy rather than that with steel slag powder.The addition of limestone powder could improve the rheological properties of the composite paste.Compared to composite paste with limestone powder,a better adsorption effect of polycarboxylate superplasticizer on the surface of the composite binder with steel slag powder could be obtained.The free water content of the composite paste with limestone powder was still higher than that of the composite paste with steel slag powder.The fluidity and rheological properties of the composite paste with limestone powder could be better.The comprehensive analysis indicated that a positive effect of limestone powder on rheological properties of composite paste at an extremely low water/binder ratio could be more dominant than that of steel slag powder.展开更多
Ti-6Al-4Zr-2Sn-6Mo alloy is one of the most recent titanium alloys processed using powder bed fusion-laser beam(PBF-LB)technology.This alloy has the potential to replace Ti-6Al-4V in automotive and aerospace applicati...Ti-6Al-4Zr-2Sn-6Mo alloy is one of the most recent titanium alloys processed using powder bed fusion-laser beam(PBF-LB)technology.This alloy has the potential to replace Ti-6Al-4V in automotive and aerospace applications,given its superior mechanical properties,which are approximately 10%higher in terms of ultimate tensile strength(UTS)and yield strength after appropriate heat treatment.In as-built conditions,the alloy is characterized by the presence of soft orthorhombicα″martensite,necessitating a postprocessing heat treatment to decompose this phase and enhance the mechanical properties of the alloy.Usually,PBFed Ti6246 components undergo an annealing process that transforms theα″martensite into anα-βlamellar microstructure.The primary objective of this research was to develop a solution treatment and aging(STA)heat treatment tailored to the unique microstructure produced by the additive manufacturing process to achieve an ultrafine bilamellar microstructure reinforced by precipitation hardening.This study investigated the effects of various solution temperatures in theα-βfield(ranging from 800 to 875℃),cooling media(air and water),and aging time to determine the optimal heat treatment parameters for achieving the desired bilamellar microstructure.For each heat treatment condition,differentα-βmicrostructures were found,varying in terms of theα/βratio and the size of the primaryα-phase lamellae.Particular attention was given to how these factors were influenced by increases in solution temperature and how microhardness correlated with the percentage of the metastableβphase present after quenching.Tensile tests were performed on samples subjected to the most promising heat treatment parameters.A comparison with literature data revealed that the optimized STA treatment enhanced hardness and UTS by13%and 23%,respectively,compared with those of the annealed alloy.Fracture surface analyses were conducted to investigate fracture mechanisms.展开更多
To enhance the mechanical properties of Mo alloys prepared through laser powder bed fusion(LPBF),a hot isostatic pressing(HIP)treatment was used.Results show that following HIP treatment,the porosity decreases from 0....To enhance the mechanical properties of Mo alloys prepared through laser powder bed fusion(LPBF),a hot isostatic pressing(HIP)treatment was used.Results show that following HIP treatment,the porosity decreases from 0.27%to 0.22%,enabling the elements Mo and Ti to diffuse fully and to distribute more uniformly,and to forming a substantial number of low-angle grain boundaries.The tensile strength soars from 286±32 MPa to 598±22 MPa,while the elongation increases from 0.08%±0.02%to 0.18%±0.02%,without notable alterations in grain morphology during the tensile deformation.HIP treatment eliminates the molten pool boundaries,which are the primary source for premature failure in LPBFed Mo alloys.Consequently,HIP treatment emerges as a novel and effective approach for strengthening the mechanical properties of LPBFed Mo alloys,offering a fresh perspective on producing high-performance Mo-based alloys.展开更多
Cu suffers from oxidation and corrosion during application due to its active chemical properties.Graphene⁃modified Cu can significantly improve its stability during application.However,copper is easily sintered at hig...Cu suffers from oxidation and corrosion during application due to its active chemical properties.Graphene⁃modified Cu can significantly improve its stability during application.However,copper is easily sintered at high temperatures,so that graphene cannot be grown inside.We demonstrate two kinds of spacers,graphite and SiO_(2),which are effective in preventing the sintering of copper and are used to assist in the growth of graphene.In the Cu⁃C system,the nucleation of graphene is scarce,and it tends to nucleate and grow on the concave surface of copper first,and then grow epitaxially to the convex surface of copper.Eventually,the obtained graphene is relatively thick.In the Cu⁃SiO_(2) system,due to the oxygen released by SiO_(2) at high temperatures,the surface of copper becomes rough.This leads to an increase in the number of graphene nucleation sites without preferred orientation,and relatively thin graphene is obtained.Two different growth mechanisms have been established for spacerseffects on graphene growth.It provides insights for graphene engineering for further applications.展开更多
The use of recycled concrete and oyster shells as partial cement and aggregate replacements is ongoing research to solve this multifaceted problem of concrete waste in the construction industry as well as waste from o...The use of recycled concrete and oyster shells as partial cement and aggregate replacements is ongoing research to solve this multifaceted problem of concrete waste in the construction industry as well as waste from oyster shell farming. However, there is a lack of evidence on the possibility of producing a fully recycled composite consisting of recycled concrete and oyster shell without the need for new cement and natural aggregates. In this study, recycled concrete powder (RCP) and oyster shell were used to produce a green composite. Separate ground and combined ground (separate ground and co-ground) RCP and oyster shells are used to determine the effects of grinding approaches on the mechanical and chemical properties of the composite. The composite samples were molded via press molding by applying 30 MPa of pressure for 10 minutes. The results revealed that the composite prepared via the combined ground approach presented the highest flexural strength compared to the separate ground and unground samples. The FTIR and XRD characterization results revealed no chemical or phase alterations in the raw materials or the resulting composites before and after grinding. SEM analysis revealed that combined grinding reduced the particles’ size and improved the dispersion of the mixture, thereby increasing the strength.展开更多
Through a modified inherent strain model based on the minimum residual stress and deformation,three building schemes with different building postures and support structures were evaluated by finite element analysis.Re...Through a modified inherent strain model based on the minimum residual stress and deformation,three building schemes with different building postures and support structures were evaluated by finite element analysis.Results demonstrate that according to the principle of reducing the overall height of the building and reducing the support structure with a large tilt angle from the building direction,the residual stress and deformation can be effectively reduced by proper design of building posture and support before laser powder bed melting.Moreover,without the data of thermophysical property variation of Ti-6Al-4V artificial knee implants with temperature,predicting the residual stress and deformation with acceptable accuracy and reduced time cost can be achieved by the inherent strain model.展开更多
Increasing concern over the amount of insecticide residues in food has encouraged research for ecologically sound strategies to effectively manage stored-product insect pests and protect living organisms and the envir...Increasing concern over the amount of insecticide residues in food has encouraged research for ecologically sound strategies to effectively manage stored-product insect pests and protect living organisms and the environment. Botanicals were evaluated as potential alternatives to control maize weevil, Sitophilus zeamais Motschulsky, in stored sorghum, Sorghum bicolor (L.) Moench. Beetles and moths of stored grain at farm and consumer levels damage 5 - 35% worldwide and >40% in tropical countries. Maize weevil is the most damaging storage insect of sorghum grain. Management of storage insects relies on insecticides that leave residues in food and the environment. Treatments were powders of neem bark, Azadirachta indica;mesquite pods, Prosopis glandulosa;milkweed leaves, Asclepias speciosa;and a check (no botanical powder). Eight newly emerged maize weevils were provided 5 g of Malisor-84 grain treated with three doses of each plant powder. Every 2 days, data were recorded on the number of adults killed by each treatment. Percentage killed was calculated by dose per treatment and compared with the check. Grain loss was calculated based on initial and final weights. LD50 was determined by probit analysis, and associations between variables were assessed by simple linear correlation. Powder of mesquite and milkweed at 0.2 g were more effective than neem or the check in killing S. zeamais (>90%) and reducing grain damage (34 - 35.2%) and weight loss (0.8%). Milkweed at 0.1 g and neem at 0.2 g killed 78.1% of weevils. Neem at 0.05 g was slow acting, resulting in 62.5% dead and more grain damage (59.5%) and weight loss (3.6%). Botanicals at low doses (LD50 = 0.2 - 0.4 g) showed efficacy in controlling maize weevils and are recommended alternatives to guarantee quantity and quality of stored cereal grains.展开更多
The leaching process of magnesiothermic self-propagating product generated during the multistage deep reduction process was investigated.The influence of magnesiothermic self-propagating product particle size,HCl solu...The leaching process of magnesiothermic self-propagating product generated during the multistage deep reduction process was investigated.The influence of magnesiothermic self-propagating product particle size,HCl solution concentration,and leaching solution temperature on the leaching behavior of elements Al and V was investigated.Results demonstrate that the leaching rate of Al and V is increased with the rise in leaching solution temperature,the increase in HCl solution concentration,and the enlargement of magnesiothermic self-propagating product particle size.The leaching processes of Al and V are consistent with the chemical reaction control model.When the magnesiothermic self-propagation product with D_(50) of 59.4μm is selected as the raw material,the leaching temperature is 40℃,and 1 mol/L HCl solution is employed,after leaching for 180 min,the leaching rates of Al and V are 24.8%and 12.6%,respectively.The acid-leached product exhibits a porous structure with a specific surface area of 3.5633 m^(2)/g.展开更多
Four types of resins,P1–P4,are used as binders for FeSiBC amorphous powder,which are then press-molded and heat-treated to fabricate magnetic powder cores(MPCs).By testing the permeability,loss,density,and radial cru...Four types of resins,P1–P4,are used as binders for FeSiBC amorphous powder,which are then press-molded and heat-treated to fabricate magnetic powder cores(MPCs).By testing the permeability,loss,density,and radial crush strength of MPCs,the effect of the binder on the magnetic properties of the cores is investigated and the best resin is found.The results show that the silicone resin P3 exhibits the best thermal stability,retaining 82.1%of its mass after heat treatment at 430°C.This contributes to improving the insulation of MPCs and reducing the eddy current loss,which is 46.06 mW cm^(−3)(150 kHz,20 mT)with the mechanical strength of 11.13 MPa.The bonding of epoxy resin P4 is superior to that of other resins,which significantly improves the powder compactness and makes MPCs density reach 5.67 g cm^(−3),and its permeability is as high as 28.7.The two types of resins have different advantages,and both lead to MPCs with excellent properties.展开更多
Ti-xNb alloys produced by laser powder bed fusion(LPBF)from mixed powder usually exhibit an inhomogeneous elemental distribution,leading to a deterioration in mechanical properties.To address this issue,we proposed a ...Ti-xNb alloys produced by laser powder bed fusion(LPBF)from mixed powder usually exhibit an inhomogeneous elemental distribution,leading to a deterioration in mechanical properties.To address this issue,we proposed a strategy to achieve heterostructure in laser powder bed fused Ti-xNb alloys from mixed powders through precipitation ofωwithinβ.Moreover,the effect of Nb content on the micro structure and mechanical behavior of Ti-xNb alloys was studied.The results indicated that in-situ laser re-melting can realize the homogeneous elemental distribution in Ti-xNb alloys.When the Nb content increases from 30 wt%,35 wt%to40 wt%,Ti-xNb alloys experience a transformation from β+α' to β+ω and monolithic β.Specifically,ωnano-precipitates in Ti-35Nb alloy are only distributed in some β grains,forming a heterostructure with“softβ”and“hard β+ω”grains.As a result,LPBF-produced Ti-35Nb alloy demonstrates excellent mechanical properties,with yield strength of ^(792±6)MPa,tensile strength of ^(806±7)MPa,Young's modulus of ^(68±6)GPa,and uniform elongation of ^(18.0±1.1)%.The Frank-Read mechanism induces dislocation proliferation and dislocation cross-slip,and the geometrically necessary dislocations(GNDs)are induced at the heterogeneous interface of“softβ”and“hard β+ω”grains,resulting in an enhancement in the strength-ductility synergy of Ti-35Nb alloy produced by LPBF.This work provides an innovative strategy to improve the strength-ductility synergy of LPBF-produced Ti-xNb alloys from mixed powders by tailoring ω nano-precipitates.展开更多
A comparative study on the performance of gas atomized(GA)and rotating-disk atomized(RDA)aluminum alloy powders produced on industrial scale for laser directed energy deposition(L-DED)process was carried out.The powde...A comparative study on the performance of gas atomized(GA)and rotating-disk atomized(RDA)aluminum alloy powders produced on industrial scale for laser directed energy deposition(L-DED)process was carried out.The powder characteristics,the printing process window,and the quality,microstructure,and mechanical properties of printed parts were taken into account for comparison and discussion.The results demonstrate that the RDA powder is superior to the GA powder in terms of sphericity,surface quality,internal defects,flowability,and apparent density,together with a larger printing process window during the L-DED parts fabrication.Besides,the resultant parts from the RDA powder have higher dimensional accuracy,lower internal defects,more uniform and finer microstructure,and more favorable mechanical properties than those from the GA powder.展开更多
基金supported by Fundamental Research Funds for the Central Universities(300102214908)Innovation Capability Support Program of Shaanxi(2022TD-07).
文摘To reduce the temperature diseases of asphalt pavement,improve the service quality of road and extend service life,the research of inorganic powders that reduce the temperature of asphalt pavements was systematically sorted out.The common types,physicochemical properties and application methods of inorganic powders were defined.The road performances of modified asphalt and its mixture were evaluated.The modification mechanism of inorganic powders in asphalt was analyzed.On this basis,the cooling effect and cooling mechanism of inorganic powders was revealed.The results indicate that inorganic powders are classified into hollow,porous,and energy conversion types.The high-temperature performance of inorganic powders modified asphalt and its mixture is significantly improved,while there is no significant change in low-temperature performance and water stability.The average increase in rutting resistance factor(G*/sin(δ))and dynamic stability is 40%–72%and 30%–50%,respectively.The modification mechanism of inorganic powders in asphalt is physical blending.The thermal conductivity of hollow and porous inorganic powders modified asphalt mixture decreases by 30.05%and 43.14%,respectively.The temperature of hollow,porous and energy conversion inorganic powders modified asphalt mixture at 5 cm decreases by 2.3 ℃–3.5 ℃,0.8 ℃–3.7 ℃and 4.1 ℃–4.7℃,respectively.Hollow and porous inorganic powders block heat conduction,while energy conversion inorganic powders achieve cooling through their functional properties.
基金partially funded by the National Natural Science Foundation of China(52074255,52274412)。
文摘Silicon nanowires(SiNWs)have been used in a wide variety of applications over the past few decades due to their excellent material properties.The only drawback is the high production cost of SiNWs.The preparation of SiNWs from photovoltaic waste silicon(WSi)powders,which are high-volume industrial wastes,not only avoids the secondary energy consumption and environmental pollution caused by complicated recycling methods,but also realizes its high-value utilization.Herein,we present a method to rapidly convert photovoltaic WSi powders into SiNWs products.The flash heating and quenching provided by carbothermal shock induce the production of free silicon atoms from the WSi powders,which are rapidly reorganized and assembled into SiNWs during the vapor-phase process.This method allows for the one-step composite of SiNWs and carbon cloth(CC)and the formation of SiC at the interface of the silicon(Si)and carbon(C)contact to create a stable chemical connection.The obtained SiNWs-CC(SiNWs@CC)composites can be directly used as lithium anodes,exhibiting high initial coulombic efficiency(86.4%)and stable cycling specific capacity(2437.4 mA h g^(-1)at 0.5 A g^(-1)after 165 cycles).In addition,various SiNWs@C composite electrodes are easily prepared using this method.
基金supported by the National Natural Science Foundation of China(Nos.52275395,51935014,and 82072084)the Science and Technology Innovation Program of Hunan Province(No.2023RC3046)+4 种基金the Young Elite Scientists Sponsorship Program byCAST(No.2020QNRC002)the NationalKeyResearchand Development Program of China(No.2023YFB4605800)the Central South University Innovation-Driven Research Programme(No.2023CXQD023)the Jiangxi Provincial Natural Science Foundation of China(No.20224ACB204013)the Project of State Key Laboratory of Precision Manufacturing for Extreme Service Performance,Central South University.
文摘Magnetostrictive Fe-Ga alloys have captivated substantial focus in biomedical applications because of their exceptional transition efficiency and favorable cytocompatibility.Nevertheless,Fe-Ga alloys always exhibit frustrating magnetostriction coefficients when presented in bulk dimensions.It is well-established that the magnetostrictive performance of Fe-Ga alloys is intimately linked to their phase and crystal structures.In this study,various concentrations of boron(B)were doped into Fe_(81)Ga_(19) alloys via the laser-beam powder bed fusion(LPBF)technique to tailor the crystal and phase structures,thereby improving the magnetostrictive performance.The results revealed the capacity for quick solidification of the LPBF process in expediting the solid solution of B element,which increased both lattice distortion and dislocations within the Fe-Ga matrix.These factors contributed to an elevation in the density of the modified-D0_(3) phase structure.Moreover,the prepared Fe-Ga-B alloys also exhibited a(001)preferred grain orientation caused by the high thermal gradients during the LPBF process.As a result,a maximum magnetostriction coefficient of 105 ppm was achieved in the(Fe_(81)Ga_(19))_(98.5)B_(1.5) alloy.In alternating magnetic fields,all the LPBF-prepared alloys showed good dynamic magnetostriction response without visible hysteresis,while the(Fe_(81)Ga_(19))_(98.5)B_(1.5) alloy presented a notable enhancement of~30%in magnetostriction coefficient when compared with the Fe_(81)Ga_(19) alloy.Moreover.the(Fe_(81)Ga_(19))_(98.5)B_(1.5) alloy exhibited favorable biocompatibility and osteogenesis,as confirmed by increased alkaline phosphatase(ALP)activity and the formation of mineralized nodules.These findings suggest that the B-doped Fe-Ga alloys combined with the LPBF technique hold promise for the development of bulk magnetostrictive alloys that are applicable for bone repair applications.
基金financially supported by the Ministry of Science and Technology of China via the National Key Research&Development Plan(Nos.2022YFB3707105 and 2020YFA0405900)Jiangsu Department of Science and Technology via Provincial Key Research&Development(Industrial Foresight and Key Core Technology,No.BE2021037)+1 种基金Department of the National Science Foundation of China(No.52204390)the Natural Science Foundation of Jiangsu Province(No.BK20202010).
文摘Laser additively manufactured(LAM)Ni-based superalloys commonly exhibit low strength and high residual stress in the as-built state,requiring post-heat treatment to improve mechanical properties.We propose a modified heat treatment(MHT)process that only involves a single-step aging at 650℃ for 4 h to achieve high strength,high ductility,and low residual stress simultaneously in a laser powder bed fusion(LPBF)-processed Inconel 718(IN718)alloy.The MHT treated alloy exhibits comparable tensile strength(1368 MPa)to the conventional solution plus two-step aging(SA)treated alloy(1398 MPa),while the tensile elongation(∼21.7%for MHT treated alloy and 13.4%for SA treated alloy)is 60%higher and the residual stress(∼195 MPa)is 20%lower than the SA treated alloy.The balanced high performance of the MHT IN718 alloy was mainly attributed to the precipitation of abundantγ’’phase with a size of∼5 nm,while the original nano-sized Laves precipitates and dislocation cells were mostly retained.The finer size and higher fraction ofγ”of the MHT sample mainly result from the dislocation structure and compositional variations in the as-built IN718,which promotes precipitation during aging.The retention of Laves phase,and cellular dislocation network in the MHT alloy also contributes to work hardening during tension and suspends the occurrence of necking.This study unveils a unique strengthening and toughening mechanism in the Ni-based superalloy produced by LAM with the presence of abundant Laves precipitates and provides a simple,low energy-consumption and cost-effective heat treatment route for achieving desirable mechanical properties.
基金supported by the National Natural Science Foundation of China(Grant Nos.52205140,52175129)the Outstanding Youth Foundation of Hunan Province(Grant No.2023JJ20041)the Science and Technology Innovation Program of Hunan Province(2023RC3241).
文摘This work investigated the anisotropy tensile properties of Inconel 625 alloy fabricated by laser powder bed fusion (LPBF) under various tests temperature, focusing the anisotropy evolution during the high temperature. The microstructure contained columnar grains with (111) texture in the vertical plane (90° sample), while a large equiaxed grain with (100) texture was produced in the horizontal plane (0° sample). As for 45° sample, a large number of equiaxed grains and a few columnar grains with (111) texture can be observed. The sample produced at a 0° orientation demonstrates the highest tensile strength, whereas the 90° sample exhibits the greatest elongation. Conversely, the 45° sample displays the least favorable overall performance. As the tests temperature increased from room temperature to 600℃, the anisotropy rate of ultimate tensile strength, yield strength and ductility between 0° and 45° samples, decreased from 8.98 to 6.96%, 2.36 to 1.28%, 19.93 to 12.23%, as well as between 0° and 90° samples decreased from 4.87 to 4.03%, 11.88 to 7.21% and 14.11 to 6.89%, respectively, because of the recovery of oriented columnar grains.
文摘BACKGROUND Ulcerative colitis(UC)is a chronic inflammatory disease affecting the colon.The most common psychological issue in UC patients is varying degrees of depre-ssion,which affects the condition and quality of life of UC patients and may lead to deterioration of the patient’s condition.UC drugs combined with anti-anxiety and antidepression drugs can alleviate symptoms of both depression and UC.Brain-derived neurotrophic factor(BDNF)precursor(proBDNF)/p75 neurotrophin receptor(p75NTR)/sortilin and BDNF/tropomyosin receptor kinase B(TrkB)signalling balance is essential for maintaining brain homeostasis and preventing the development of depressive behaviours.AIM To explore the mechanism by which Wuling powder regulates the proBDNF/p75NTR/sortilin and BDNF/TrkB pathways in the treatment of UC with depre-ssion.METHODS Depression was established in C57BL/6J mice via chronic restraint stress,and the UC model was induced with dextran sodium sulfate(DSS).In the treatment stage,mesalazine(MS)was the basic treatment,Wuling powder was the experimental treatment,and fluoxetine was the positive control drug for treating depression.Changes in intestinal mucosal inflammation,behaviour,and the proBDNFp75NTR/sortilin and BDNF/TrkB pathways were evaluated.RESULTS In the depression groups,Wuling powder decreased the immobility time,increased the distance travelled in the central zone and the total distance travelled,and restored balance in the proBDNF/p75NTR/sortilin and BDNF/TrkB signalling pathways.In the DSS and chronic restraint stress+DSS groups,immobility time increased,distance travelled in the central zone and total distance travelled decreased,activity of the proBDNF/p75NTR/sortilin pathway was upregulated,and activity of the BDNF/TrkB pathway was downregulated,indicating that mice with UC often have comorbid depression.Compared with those of MS alone,Wuling powder combined with MS further decreased the colon histopathological scores and the expression levels of tumor necrosis factor-alpha and interleukin-6 mRNAs.CONCLUSION This study confirmed that Wuling powder may play an antidepressant role by regulating the balance of the proBDNF/p75NTR/sortilin and BDNF/TrkB signalling pathways and further relieve intestinal inflammation in UC.
基金Funded by the National Natural Science Foundation of China(Nos.U1934206,52108260)China Academy of Railway Sciences Fund(No.2021YJ078)+1 种基金Railway Engineering Construction Standard Project(No.2023-BZWW-006)New Cornerstone Science Foundation through the XPLORER PRIZE。
文摘In order to achieve the large-scale application of manufactured sand in railway high-strength concrete structure,a series of high-strength manufactured sand concrete(HMC)are prepared by taking the manufactured sand lithology(tuff,limestone,basalt,granite),stone powder content(0,5%,10%,15%)and concrete strength grade(C60,C80,C100)as variables.The evolution of mechanical properties of HMC and the correlation between cubic compressive strength and other mechanical properties are studied.Compared to river sand,manufactured sand enhances the cubic compressive strength,axial compressive strength and elastic modulus of concrete,while its potential microcracks weaken the flexural strength and splitting tensile strength of concrete.Stone powder content displays both positive and negative effects on mechanical properties of HMC,and the stone powder content is suggested to be less than 10%.The empirical formulas between cubic compressive strength and other mechanical properties are proposed.
基金financially supported by the Agency for Science,Technology and Research(A*Star),Republic of Singapore,under the Aerospace Consortium Cycle 12“Characterization of the Effect of Wire and Powder Deposited Materials”(No.A1815a0078)。
文摘The feasibility of manufacturing Ti-6Al-4V samples through a combination of laser-aided additive manufacturing with powder(LAAM_(p))and wire(LAAM_(w))was explored.A process study was first conducted to successfully circumvent defects in Ti-6Al-4V deposits for LAAM_(p) and LAAM_(w),respectively.With the optimized process parameters,robust interfaces were achieved between powder/wire deposits and the forged substrate,as well as between powder and wire deposits.Microstructure characterization results revealed the epitaxial prior β grains in the deposited Ti-6Al-4V,wherein the powder deposit was dominated by a finerα′microstructure and the wire deposit was characterized by lamellar α phases.The mechanisms of microstructure formation and correlation with mechanical behavior were analyzed and discussed.The mechanical properties of the interfacial samples can meet the requirements of the relevant Aerospace Material Specifications(AMS 6932)even without post heat treatment.No fracture occurred within the interfacial area,further suggesting the robust interface.The findings of this study highlighted the feasibility of combining LAAM_(p) and LAAM_(w) in the direct manufacturing of Ti-6Al-4V parts in accordance with the required dimensional resolution and deposition rate,together with sound strength and ductility balance in the as-built condition.
基金supported by the National Key Research and Development Program of China(No.2021YFB3701000)the National Natural Science Foundation of China(Nos.51971130,52201129,U21A2047,51821001,U2037601)+2 种基金support by the China Postdoctoral Science Foun-dation(2023M742219)the Postdoctoral Fellowship Program of CPSF under Grant Number GZB20240419support by the Ministry of Education,Singapore,under its Academic Research Fund Tier 2(MOE-T2EP50221-0013).
文摘Additive manufacturing (AM) of high-strength metallic alloys frequently encounters detrimental distortion and cracking, attributed to the accumulation of thermal stresses. These issues significantly impede the practical application of as-printed components. This study examines the Mg-15Gd-1Zn-0.4Zr (GZ151K, wt.%) alloy, a prototypical high-strength casting Mg-RE alloy, fabricated through laser powder bed fusion (LPBF). Despite achieving ultra-high strength, the GZ151K alloy concurrently exhibits a pronounced cold-cracking susceptibility. The as-printed GZ151K alloy consists of almost fully fine equiaxed grains with an average grain size of merely 2.87 µm. Subsequent direct aging (T5) heat treatment induces the formation of dense prismatic β' precipitates. Consequently, the LPBF-T5 GZ151K alloy manifests an ultra-high yield strength of 405 MPa, surpassing all previously reported yield strengths for Mg alloys fabricated via LPBF and even exceeding that of its extrusion-T5 counterpart. Interestingly, as-printed GZ151K samples with a build height of 2 mm exhibit no cracking, whereas samples with build heights ranging from 4 to 18 mm demonstrate severe cold cracking. Thermal stress simulation also suggests that the cold cracking susceptibility increases significantly with increasing build height. The combination of high thermal stress and low ductility in the as-printed GZ151K alloy culminates in a high cold cracking susceptibility. This study offers novel insights into the intricate issue of cold cracking in the LPBF process of high-strength Mg alloys, highlighting the critical balance between achieving high strength and mitigating cold cracking susceptibility.
文摘Introduction The widespread use of cement in concrete leads to increased carbon emissions,so the demand for supplementary cementitious materials increases significantly.Limestone powder and steel slag powder are widely used as supplementary cementitious materials in modern concrete.However,for UHPC and self-compacting concrete,an extremely low water/binder(W/B)ratio is on one hand a key factor in achieving ultra-high strength and ultra-low porosity of the materials,on the other hand,also leads to the deterioration of the rheological properties of the fresh paste.Meanwhile,the existing researches focus on the influence of single limestone powder or steel slag powder on the mechanical properties or microstructure of cement-based materials.Little work on the influence of steel slag powder or limestone powder on the rheological properties of composite paste at an extremely low water/binder ratio has been investigated quantitatively.The mechanism of the effect of steel slag powder or limestone powder on the rheological properties of composite paste at extremely low water/binder ratios is still unclear.In this work,the effects of steel slag powder and limestone powder on the rheological properties of composite paste at different low water/binder ratios were analyzed via determining the flow diameter,setting time,marsh cone flow time,rheological parameters,and total organic carbon content.Methods A composite paste was prepared with P.I 42.5 ordinary Portland cement,steel slag powder,limestone powder,blast furnace slag and silica fume as raw materials in a certain proportion.To achieve the preparation of composite paste with extremely low water/binder ratios,a polycarboxylate superplasticizer with a water/reducing rate of 40%(Jiangsu Subot New Materials Co.,Ltd.,China)was used.The dosage of polycarboxylate superplasticizer for the composite paste with different water/binder ratios of 0.16 and 0.21 was 2%and 0.8%,respectively.Composite pastes with different proportions of steel slag powder or limestone powder at water/binder ratios of 0.16 and 0.21 were prepared.The flow diameter(i.e.,the larger the flow diameter,the better the fluidity),setting time(i.e.,the time when the fluidity is lost)and marsh cone flow time(i.e.,the shorter the flow time,the better the fluidity)were determined to analyze the fluidity of the composite pastes.the rheological properties of composite paste at a water/binder ratio of 0.16 for rheological properties tests were determined,and the rheological parameters were obtained by the H-B model.The adsorption performance of the polycarboxylate superplasticizer was analyzed by testing the TOC content.Results and discussion When the ratio of water/binder is 0.16,both limestone powder and steel slag powder initially increase the flow diameter of the composite paste.However,the fluidity of the composite paste decreases over time,and the reduction is more pronounced with steel slag powder.This is because the nucleation and hydration promotion effect of limestone powder can reduce the loss rate of flow diameter,while the rough particles of steel slag powder increase the internal friction force,resulting in a decrease in the flow diameter of composite paste.Adding limestone powder and steel slag powder both shortens the setting time and marsh cone flow time of the composite paste.However,the steel slag powder addition of 30%delays the final setting time due to its delaying effect.Also,limestone powder can enhance the thixotropy and reduce the yield stress and plastic viscosity,thereby improving the rheological properties.In contrast,steel slag powder can increase the yield stress and plastic viscosity,thereby weakening the rheological properties and thixotropy.Steel slag powder and limestone powder both can enhance the adsorption effect of polycarboxylate superplasticizer.Steel slag powder has a stronger adsorption effect.The composite paste containing limestone powder has a higher free water content.This is because the rough and porous surface of steel slag itself and the uneven particle shape lead to the physical adsorption of polycarboxylate superplasticizer molecules on the surface of steel slag particles,thereby reducing the effective content of the water reducer dispersion.Increasing the water/binder ratio to 0.21 results in a decrease in the flow diameter of the composite paste.Furthermore,the setting time and marsh cone flow time can prolong due to the reduction in the dosage of polycarboxylate superplasticizer.Conclusions The results showed that the fluidity loss rate of composite paste with limestone powder could be lower than that of composite paste with steel slag powder.Compared to steel slag powder,the addition of limestone powder reduced the setting time and marsh cone flow time of the composite paste.The addition of limestone powder could shorten the yield stress and plastic viscosity of the composite paste.Therefore,the composite paste with limestone powder had better rheological properties and stronger thixotropy rather than that with steel slag powder.The addition of limestone powder could improve the rheological properties of the composite paste.Compared to composite paste with limestone powder,a better adsorption effect of polycarboxylate superplasticizer on the surface of the composite binder with steel slag powder could be obtained.The free water content of the composite paste with limestone powder was still higher than that of the composite paste with steel slag powder.The fluidity and rheological properties of the composite paste with limestone powder could be better.The comprehensive analysis indicated that a positive effect of limestone powder on rheological properties of composite paste at an extremely low water/binder ratio could be more dominant than that of steel slag powder.
基金financed by the European Union-Next Generation EU(National Sustainable Mobility Center CN00000023,Italian Ministry of University and Research Decree n.1033-17/06/2022,Spoke 11-Innovative Materials&Lightweighting)。
文摘Ti-6Al-4Zr-2Sn-6Mo alloy is one of the most recent titanium alloys processed using powder bed fusion-laser beam(PBF-LB)technology.This alloy has the potential to replace Ti-6Al-4V in automotive and aerospace applications,given its superior mechanical properties,which are approximately 10%higher in terms of ultimate tensile strength(UTS)and yield strength after appropriate heat treatment.In as-built conditions,the alloy is characterized by the presence of soft orthorhombicα″martensite,necessitating a postprocessing heat treatment to decompose this phase and enhance the mechanical properties of the alloy.Usually,PBFed Ti6246 components undergo an annealing process that transforms theα″martensite into anα-βlamellar microstructure.The primary objective of this research was to develop a solution treatment and aging(STA)heat treatment tailored to the unique microstructure produced by the additive manufacturing process to achieve an ultrafine bilamellar microstructure reinforced by precipitation hardening.This study investigated the effects of various solution temperatures in theα-βfield(ranging from 800 to 875℃),cooling media(air and water),and aging time to determine the optimal heat treatment parameters for achieving the desired bilamellar microstructure.For each heat treatment condition,differentα-βmicrostructures were found,varying in terms of theα/βratio and the size of the primaryα-phase lamellae.Particular attention was given to how these factors were influenced by increases in solution temperature and how microhardness correlated with the percentage of the metastableβphase present after quenching.Tensile tests were performed on samples subjected to the most promising heat treatment parameters.A comparison with literature data revealed that the optimized STA treatment enhanced hardness and UTS by13%and 23%,respectively,compared with those of the annealed alloy.Fracture surface analyses were conducted to investigate fracture mechanisms.
基金National Natural Science Foundation of China(52105385)Stable Support Plan Program of Shenzhen Natural Science Fund(20220810132537001)+2 种基金Guangdong Basic and Applied Basic Research Foundation(2022A1515010781)Joint Fund of Henan Province Science and Technology R&D Program(225200810002)Fundamental Research Funds of Henan Academy of Sciences(240621041)。
文摘To enhance the mechanical properties of Mo alloys prepared through laser powder bed fusion(LPBF),a hot isostatic pressing(HIP)treatment was used.Results show that following HIP treatment,the porosity decreases from 0.27%to 0.22%,enabling the elements Mo and Ti to diffuse fully and to distribute more uniformly,and to forming a substantial number of low-angle grain boundaries.The tensile strength soars from 286±32 MPa to 598±22 MPa,while the elongation increases from 0.08%±0.02%to 0.18%±0.02%,without notable alterations in grain morphology during the tensile deformation.HIP treatment eliminates the molten pool boundaries,which are the primary source for premature failure in LPBFed Mo alloys.Consequently,HIP treatment emerges as a novel and effective approach for strengthening the mechanical properties of LPBFed Mo alloys,offering a fresh perspective on producing high-performance Mo-based alloys.
文摘Cu suffers from oxidation and corrosion during application due to its active chemical properties.Graphene⁃modified Cu can significantly improve its stability during application.However,copper is easily sintered at high temperatures,so that graphene cannot be grown inside.We demonstrate two kinds of spacers,graphite and SiO_(2),which are effective in preventing the sintering of copper and are used to assist in the growth of graphene.In the Cu⁃C system,the nucleation of graphene is scarce,and it tends to nucleate and grow on the concave surface of copper first,and then grow epitaxially to the convex surface of copper.Eventually,the obtained graphene is relatively thick.In the Cu⁃SiO_(2) system,due to the oxygen released by SiO_(2) at high temperatures,the surface of copper becomes rough.This leads to an increase in the number of graphene nucleation sites without preferred orientation,and relatively thin graphene is obtained.Two different growth mechanisms have been established for spacerseffects on graphene growth.It provides insights for graphene engineering for further applications.
文摘The use of recycled concrete and oyster shells as partial cement and aggregate replacements is ongoing research to solve this multifaceted problem of concrete waste in the construction industry as well as waste from oyster shell farming. However, there is a lack of evidence on the possibility of producing a fully recycled composite consisting of recycled concrete and oyster shell without the need for new cement and natural aggregates. In this study, recycled concrete powder (RCP) and oyster shell were used to produce a green composite. Separate ground and combined ground (separate ground and co-ground) RCP and oyster shells are used to determine the effects of grinding approaches on the mechanical and chemical properties of the composite. The composite samples were molded via press molding by applying 30 MPa of pressure for 10 minutes. The results revealed that the composite prepared via the combined ground approach presented the highest flexural strength compared to the separate ground and unground samples. The FTIR and XRD characterization results revealed no chemical or phase alterations in the raw materials or the resulting composites before and after grinding. SEM analysis revealed that combined grinding reduced the particles’ size and improved the dispersion of the mixture, thereby increasing the strength.
基金Natural Science Foundation of Shandong Province(ZR2020ME020)。
文摘Through a modified inherent strain model based on the minimum residual stress and deformation,three building schemes with different building postures and support structures were evaluated by finite element analysis.Results demonstrate that according to the principle of reducing the overall height of the building and reducing the support structure with a large tilt angle from the building direction,the residual stress and deformation can be effectively reduced by proper design of building posture and support before laser powder bed melting.Moreover,without the data of thermophysical property variation of Ti-6Al-4V artificial knee implants with temperature,predicting the residual stress and deformation with acceptable accuracy and reduced time cost can be achieved by the inherent strain model.
文摘Increasing concern over the amount of insecticide residues in food has encouraged research for ecologically sound strategies to effectively manage stored-product insect pests and protect living organisms and the environment. Botanicals were evaluated as potential alternatives to control maize weevil, Sitophilus zeamais Motschulsky, in stored sorghum, Sorghum bicolor (L.) Moench. Beetles and moths of stored grain at farm and consumer levels damage 5 - 35% worldwide and >40% in tropical countries. Maize weevil is the most damaging storage insect of sorghum grain. Management of storage insects relies on insecticides that leave residues in food and the environment. Treatments were powders of neem bark, Azadirachta indica;mesquite pods, Prosopis glandulosa;milkweed leaves, Asclepias speciosa;and a check (no botanical powder). Eight newly emerged maize weevils were provided 5 g of Malisor-84 grain treated with three doses of each plant powder. Every 2 days, data were recorded on the number of adults killed by each treatment. Percentage killed was calculated by dose per treatment and compared with the check. Grain loss was calculated based on initial and final weights. LD50 was determined by probit analysis, and associations between variables were assessed by simple linear correlation. Powder of mesquite and milkweed at 0.2 g were more effective than neem or the check in killing S. zeamais (>90%) and reducing grain damage (34 - 35.2%) and weight loss (0.8%). Milkweed at 0.1 g and neem at 0.2 g killed 78.1% of weevils. Neem at 0.05 g was slow acting, resulting in 62.5% dead and more grain damage (59.5%) and weight loss (3.6%). Botanicals at low doses (LD50 = 0.2 - 0.4 g) showed efficacy in controlling maize weevils and are recommended alternatives to guarantee quantity and quality of stored cereal grains.
基金Scientific and Technological Project of Nanyang(23KJGG017)Key Specialized Research&Development and Promotion Project(Scientific and Technological Project)of Henan Province(232102221022)+1 种基金College Students and Technology Innovation Fund Project of Nanyang Institute of Technology(2023139)Project of Doctoral Scientific Research Startup Fund of Nanyang Institute of Technology(NGBJ-2023-25)。
文摘The leaching process of magnesiothermic self-propagating product generated during the multistage deep reduction process was investigated.The influence of magnesiothermic self-propagating product particle size,HCl solution concentration,and leaching solution temperature on the leaching behavior of elements Al and V was investigated.Results demonstrate that the leaching rate of Al and V is increased with the rise in leaching solution temperature,the increase in HCl solution concentration,and the enlargement of magnesiothermic self-propagating product particle size.The leaching processes of Al and V are consistent with the chemical reaction control model.When the magnesiothermic self-propagation product with D_(50) of 59.4μm is selected as the raw material,the leaching temperature is 40℃,and 1 mol/L HCl solution is employed,after leaching for 180 min,the leaching rates of Al and V are 24.8%and 12.6%,respectively.The acid-leached product exhibits a porous structure with a specific surface area of 3.5633 m^(2)/g.
基金financially supported by the Key research and development project of Shandong province in China(Grant No.2022CXGC020308).
文摘Four types of resins,P1–P4,are used as binders for FeSiBC amorphous powder,which are then press-molded and heat-treated to fabricate magnetic powder cores(MPCs).By testing the permeability,loss,density,and radial crush strength of MPCs,the effect of the binder on the magnetic properties of the cores is investigated and the best resin is found.The results show that the silicone resin P3 exhibits the best thermal stability,retaining 82.1%of its mass after heat treatment at 430°C.This contributes to improving the insulation of MPCs and reducing the eddy current loss,which is 46.06 mW cm^(−3)(150 kHz,20 mT)with the mechanical strength of 11.13 MPa.The bonding of epoxy resin P4 is superior to that of other resins,which significantly improves the powder compactness and makes MPCs density reach 5.67 g cm^(−3),and its permeability is as high as 28.7.The two types of resins have different advantages,and both lead to MPCs with excellent properties.
基金supported by the National Natural Science Foundation of China(Grant Nos.92166112,52373236 and 52271132)the Natural Science Foundation of Guangdong Province(Grant No.2024A1515010658)+6 种基金the Guangdong Province International Science and Technology Cooperation Project(Grant No.2023A0505050103)the Guangxi Key Laboratory of Information Materials(Grant No.231033-K)the Open Project Program of Wuhan National Laboratory for Optoelectronics(Grant No.2021WNLOKF010)Guangzhou Science and Technology Planning Project(2024A04J9966)Guangdong Provincial Science and Technology Plan Project(2022A0505050043)The financial support from the ECU industrial grant(No.G1006320)ECU DVC strategic research fund(project number 23965)。
文摘Ti-xNb alloys produced by laser powder bed fusion(LPBF)from mixed powder usually exhibit an inhomogeneous elemental distribution,leading to a deterioration in mechanical properties.To address this issue,we proposed a strategy to achieve heterostructure in laser powder bed fused Ti-xNb alloys from mixed powders through precipitation ofωwithinβ.Moreover,the effect of Nb content on the micro structure and mechanical behavior of Ti-xNb alloys was studied.The results indicated that in-situ laser re-melting can realize the homogeneous elemental distribution in Ti-xNb alloys.When the Nb content increases from 30 wt%,35 wt%to40 wt%,Ti-xNb alloys experience a transformation from β+α' to β+ω and monolithic β.Specifically,ωnano-precipitates in Ti-35Nb alloy are only distributed in some β grains,forming a heterostructure with“softβ”and“hard β+ω”grains.As a result,LPBF-produced Ti-35Nb alloy demonstrates excellent mechanical properties,with yield strength of ^(792±6)MPa,tensile strength of ^(806±7)MPa,Young's modulus of ^(68±6)GPa,and uniform elongation of ^(18.0±1.1)%.The Frank-Read mechanism induces dislocation proliferation and dislocation cross-slip,and the geometrically necessary dislocations(GNDs)are induced at the heterogeneous interface of“softβ”and“hard β+ω”grains,resulting in an enhancement in the strength-ductility synergy of Ti-35Nb alloy produced by LPBF.This work provides an innovative strategy to improve the strength-ductility synergy of LPBF-produced Ti-xNb alloys from mixed powders by tailoring ω nano-precipitates.
基金supported by the National Natural Science Foundation of China(No.52074157)Department of Education of Guangdong Province,China(No.2023KTSCX121)Shenzhen Science and Technology Programs,China(Nos.JSGG20210802154210032,JCYJ20210324104608023,JSGG20180508152608855)。
文摘A comparative study on the performance of gas atomized(GA)and rotating-disk atomized(RDA)aluminum alloy powders produced on industrial scale for laser directed energy deposition(L-DED)process was carried out.The powder characteristics,the printing process window,and the quality,microstructure,and mechanical properties of printed parts were taken into account for comparison and discussion.The results demonstrate that the RDA powder is superior to the GA powder in terms of sphericity,surface quality,internal defects,flowability,and apparent density,together with a larger printing process window during the L-DED parts fabrication.Besides,the resultant parts from the RDA powder have higher dimensional accuracy,lower internal defects,more uniform and finer microstructure,and more favorable mechanical properties than those from the GA powder.
