The woven textile sandwich composite（WTSC） is a promising lightweight composite.In bending,two competing core shearing failure modes reduce the strength;deflection induced by the core shearing deformation reduces th...The woven textile sandwich composite（WTSC） is a promising lightweight composite.In bending,two competing core shearing failure modes reduce the strength;deflection induced by the core shearing deformation reduces the flexural rigidity.To replace a solid composite laminate,the span of WTSC panel must be greater than a critical value,which was deduced on the condition that the load capacity and flexural rigidity of the WTSC panel are equal to those of the composite laminate.Three WTSC panels were tested in bending,so that the failure modes were observed,and the critical spans were determined.Using the alternative design method,the WTSC based wind deflector with reduced weight has been fabricated and mounted on the CRH（China Railway High-speed）.展开更多
Aiming to mitigate the aerodynamic lift force imbalance between pantograph strips,which exacerbates wear and affects the current collection performance of the pantograph-catenary system,a study has been conducted to s...Aiming to mitigate the aerodynamic lift force imbalance between pantograph strips,which exacerbates wear and affects the current collection performance of the pantograph-catenary system,a study has been conducted to support the beam deflector optimization using a combination of experimental measurements and computational fluid dynamics(CFD)simulations.The results demonstrate that the size,position,and installation orientation of the wind deflectors significantly influence the amount of force compensation.They also indicate that the front strip deflectors should be installed downwards and the rear strip deflectors upwards,thereby forming a“π”shape.Moreover,the lift force compensation provided by the wind deflectors increases with the size of the deflector.Alternative wind compensation strategies,such as control circuits,are also discussed,putting emphasis on the pros and cons of various pantograph types and wind compensation approaches.展开更多
In this paper, the differences in the characteristics of airflow around thevan-body truck and of the aerodynamic drag, which were caused by the installation of a winddeflector, were studied by experimentally and numer...In this paper, the differences in the characteristics of airflow around thevan-body truck and of the aerodynamic drag, which were caused by the installation of a winddeflector, were studied by experimentally and numerically. The results show that after theinstallation of the deflector, the airflow around the top and bottom of the truck becoms smooth, theintensity of tail-vortex is weakened and its contribution area lessened. It also indicates that theaerodynamic characteristics of the airflow are changed distinctly and the aerodynamic drag isreduced considerably. The effect of the thin-wall deflector is better than the solid one indecreasing the drag. It is also concluded that proper design of the gap between the deflector bottomand the top of the driver cab can enhance the effect of the deflector in reducing drag.展开更多
When the spacecraft flies much faster than the sound speed (~1200 km/h), the airflow disturbances deflected forward from the spacecraft cannot get away from the spacecraft and form a shock wave in front of it. Shock w...When the spacecraft flies much faster than the sound speed (~1200 km/h), the airflow disturbances deflected forward from the spacecraft cannot get away from the spacecraft and form a shock wave in front of it. Shock waves have been a detriment for the development of supersonic aircrafts, which have to overcome high wave drag and surface heating from additional friction. Shock wave also produces sonic booms. The noise issue raises environmental concerns, which have precluded routine supersonic flight over land. Therefore, mitigation of shock wave is essential to advance the development of supersonic aircrafts. A plasma mitigation technique is studied. A theory is presented to show that shock wave structure can be modified via flow deflection. Symmetrical deflection evades the need of exchanging the transverse momentum between the flow and the deflector. The analysis shows that the plasma generated in front of the model can effectively deflect the incoming flow. A non-thermal air plasma, generated by on-board 60 Hz periodic electric arc discharge in front of a wind tunnel model, was applied as a plasma deflector for shock wave mitigation technique. The experiment was conducted in a Mach 2.5 wind tunnel. The results show that the air plasma was generated symmetrically in front of the wind tunnel model. With increasing discharge intensity, the plasma deflector transforms the shock from a welldefined attached shock into a highly curved shock structure with increasing standoff distance from the model;this curved shock has increased shock angle and also appears in increasingly diffused form. In the decay of the discharge intensity, the shock front is first transformed back to a well-defined curve shock, which moves downstream to become a perturbed oblique shock;the baseline shock front then reappears as the discharge is reduced to low level again. The experimental observations confirm the theory. The steady of the incoming flow during the discharge cycle is manifested by the repeat of the baseline shock front.展开更多
基金Project supported by the National Natural Science Foundation of China(Nos.11172089 and 11372095)the State Key Laboratory of Mechanics and Control of Mechanical Structures(Nos.MCMS-0212G01 and MCMS-0215G01)
文摘The woven textile sandwich composite（WTSC） is a promising lightweight composite.In bending,two competing core shearing failure modes reduce the strength;deflection induced by the core shearing deformation reduces the flexural rigidity.To replace a solid composite laminate,the span of WTSC panel must be greater than a critical value,which was deduced on the condition that the load capacity and flexural rigidity of the WTSC panel are equal to those of the composite laminate.Three WTSC panels were tested in bending,so that the failure modes were observed,and the critical spans were determined.Using the alternative design method,the WTSC based wind deflector with reduced weight has been fabricated and mounted on the CRH（China Railway High-speed）.
文摘Aiming to mitigate the aerodynamic lift force imbalance between pantograph strips,which exacerbates wear and affects the current collection performance of the pantograph-catenary system,a study has been conducted to support the beam deflector optimization using a combination of experimental measurements and computational fluid dynamics(CFD)simulations.The results demonstrate that the size,position,and installation orientation of the wind deflectors significantly influence the amount of force compensation.They also indicate that the front strip deflectors should be installed downwards and the rear strip deflectors upwards,thereby forming a“π”shape.Moreover,the lift force compensation provided by the wind deflectors increases with the size of the deflector.Alternative wind compensation strategies,such as control circuits,are also discussed,putting emphasis on the pros and cons of various pantograph types and wind compensation approaches.
文摘In this paper, the differences in the characteristics of airflow around thevan-body truck and of the aerodynamic drag, which were caused by the installation of a winddeflector, were studied by experimentally and numerically. The results show that after theinstallation of the deflector, the airflow around the top and bottom of the truck becoms smooth, theintensity of tail-vortex is weakened and its contribution area lessened. It also indicates that theaerodynamic characteristics of the airflow are changed distinctly and the aerodynamic drag isreduced considerably. The effect of the thin-wall deflector is better than the solid one indecreasing the drag. It is also concluded that proper design of the gap between the deflector bottomand the top of the driver cab can enhance the effect of the deflector in reducing drag.
文摘When the spacecraft flies much faster than the sound speed (~1200 km/h), the airflow disturbances deflected forward from the spacecraft cannot get away from the spacecraft and form a shock wave in front of it. Shock waves have been a detriment for the development of supersonic aircrafts, which have to overcome high wave drag and surface heating from additional friction. Shock wave also produces sonic booms. The noise issue raises environmental concerns, which have precluded routine supersonic flight over land. Therefore, mitigation of shock wave is essential to advance the development of supersonic aircrafts. A plasma mitigation technique is studied. A theory is presented to show that shock wave structure can be modified via flow deflection. Symmetrical deflection evades the need of exchanging the transverse momentum between the flow and the deflector. The analysis shows that the plasma generated in front of the model can effectively deflect the incoming flow. A non-thermal air plasma, generated by on-board 60 Hz periodic electric arc discharge in front of a wind tunnel model, was applied as a plasma deflector for shock wave mitigation technique. The experiment was conducted in a Mach 2.5 wind tunnel. The results show that the air plasma was generated symmetrically in front of the wind tunnel model. With increasing discharge intensity, the plasma deflector transforms the shock from a welldefined attached shock into a highly curved shock structure with increasing standoff distance from the model;this curved shock has increased shock angle and also appears in increasingly diffused form. In the decay of the discharge intensity, the shock front is first transformed back to a well-defined curve shock, which moves downstream to become a perturbed oblique shock;the baseline shock front then reappears as the discharge is reduced to low level again. The experimental observations confirm the theory. The steady of the incoming flow during the discharge cycle is manifested by the repeat of the baseline shock front.
