Emulsion electrospinning as a novel process in spinning core-sheath fibers shows a promising potential in drug release control. The volume ratio of water phase to oily phase is one of the critical parameters in formin...Emulsion electrospinning as a novel process in spinning core-sheath fibers shows a promising potential in drug release control. The volume ratio of water phase to oily phase is one of the critical parameters in forming core-sheath fibers. In this study, water phase was presented by hydrophilic tetracycline hydrochloride and oily phase by hydrophobic poly （E-caprolactone） （PCL）. The effects of volume ratios of water phase to oily phase on fiber morphology and in vitro drug release were investigated. Scanning electron microscopy （ SEM ）, transmission electron microscopy （ TEM）, and eonfoeal laser scanning microscopy（CLSM） were used to observe the morphology, core.sheath structure of the fibers and drug loading in the fibers, respectively. Samples of three different volume ratios of water phase to oily phase, 1： 25, 1：15, and 1：10, were prepared with the same concentration of drug solution. Experiment results showed that, with an increase in the volume ratios of water phase to oily phase, the fiber diameter increased and diameter distribution scattered. The drug entrapment efficiency of the fibers reduces with the increase in volume ratios, L e. , from 73.48 % in the ratio of 1 ： 25, 62.23 % in 1 ： 15, down to 45.63 % in 1：10. In vitro release tests showed that a higher volume ratio of water phase to oily phase would lead to a lower release rate resulted from thicker fiber sheath.展开更多
To establish an analytical method for determination of four bisphenols （BPA, BPB, BPF, and BPS） and two alkylphenols （4-n-OP, 4-n-NP） in water by ultra performance liquid chromatography- tandem mass spectrometry ...To establish an analytical method for determination of four bisphenols （BPA, BPB, BPF, and BPS） and two alkylphenols （4-n-OP, 4-n-NP） in water by ultra performance liquid chromatography- tandem mass spectrometry （UPLC/MS/MS）. The water samples were extracted and condensed with solid-phase extraction （SPE） using C18 cartridges and eluted by acetonitrile. Separation was carried out with Acquity BEH C8 column and detection were performed by UPLC/MS/MS. Quantification was calculated by using the internal standard BPA-d16 and 4-n-NP-d8. The linear correlation coefficients of these compounds in the range of 1.0-100.0μg/L were all over 0.999. The minimum detectable concentrations were 0.75-1.0 ng/L, and the recoveries ranged from 87.0% to 106.9%.展开更多
An improved method for trace level quantification of dicyandiamide in stream water has been developed. This method includes sample pretreatment using solid phase extraction.The extraction procedure（including loading,...An improved method for trace level quantification of dicyandiamide in stream water has been developed. This method includes sample pretreatment using solid phase extraction.The extraction procedure（including loading, washing, and eluting） used a flow rate of1.0 m L/min, and dicyandiamide was eluted with 20 m L of a methanol/acetonitrile mixture（V/V = 2：3）, followed by pre-concentration using nitrogen evaporation and analysis with high performance liquid chromatography–ultraviolet spectroscopy（HPLC–UV）. Sample extraction was carried out using a Waters Sep-Pak AC-2 Cartridge（with activated carbon）.Separation was achieved on a ZIC-Hydrophilic Interaction Liquid Chromatography（ZIC-HILIC）（50 mm × 2.1 mm, 3.5 μm） chromatography column and quantification was accomplished based on UV absorbance. A reliable linear relationship was obtained for the calibration curve using standard solutions（R^2〉 0.999）. Recoveries for dicyandiamide ranged from 84.6% to 96.8%, and the relative standard deviations（RSDs, n = 3） were below 6.1% with a detection limit of 5.0 ng/m L for stream water samples.展开更多
In order to simulate the unsteady seepage in soil slopes under water level rise condition, including water seepage and air seepage, and to investigate the influence of the capillary pressure on the slope safety coeffi...In order to simulate the unsteady seepage in soil slopes under water level rise condition, including water seepage and air seepage, and to investigate the influence of the capillary pressure on the slope safety coefficient, the water-air two-phase flow model was used and its solving method and definition condition were given. By the two-phase flow model, the pore air and pore water seepage of a soil slope under steady seepage and water level rise conditions were shown, and the slope stability in different cases was analyzed from the simulation results. We find that under water level rise condition, the pore air pressure in the unsaturated zone increased evidently and the capillary pressure should be considered while the pore air pressure can be neglected in slope stability analysis.展开更多
We investigate the dynamic characteristics of oil-gas-water three-phase flow in terms of chaotic attractor comparison. In particular, we extract a statistic to characterize the dynamical difference in attractor probab...We investigate the dynamic characteristics of oil-gas-water three-phase flow in terms of chaotic attractor comparison. In particular, we extract a statistic to characterize the dynamical difference in attractor probability distribution. We first take time series from Logistic chaotic system with different parameters as examples to demonstrate the effectiveness of the method. Then we use this method to investigate the experimental signals from oil-gas-water three-phase flow. The results indicate that the extracted statistic is very sensitive to the change of flow parameters and can gain a quantitatively insight into the dynamic characteristics of different flow patterns.展开更多
This paper developed a fluorometric method for the sensitive determination of nonylphenol in water samples by preconcentration with zirconium doped titanium dioxide nanotubes solid phase extraction.The parameters on e...This paper developed a fluorometric method for the sensitive determination of nonylphenol in water samples by preconcentration with zirconium doped titanium dioxide nanotubes solid phase extraction.The parameters on extraction that would influence the enrichment performance such as the kind and volume of eluent,sample pH,sample flow rate,and sample volume were optimized in detail.Under the optimal conditions,the proposed method provided an excellent linear range of 1-150 mg/L and good LOD of 0.076 mg/L.The relative standard deviation（RSD,n = 6） was 2.8%.Proposed method was also used for the analysis of real water samples and the spiked recoveries were satisfied in the range of 98.7-103%.展开更多
This paper describes a reserved-phase high performance liquid chromatographic method for detecting melamine (MEL) and related analogues, cyanuric acid (CYA), ammeline (AML), and ammelide (AMD), using a 100% water mobi...This paper describes a reserved-phase high performance liquid chromatographic method for detecting melamine (MEL) and related analogues, cyanuric acid (CYA), ammeline (AML), and ammelide (AMD), using a 100% water mobile phase. Chromatographic separation was performed an Inertsil? ODS-4 (250 × 4.6 mm, 5 μm) with a water mobile phase and a photodiode-array detector. The monitoring wavelength was adjusted to 210 nm which represents an average maximum for all the analytes. The total run time was < 8 min. The method shows high stability, significant linearity and satisfactory sensitivity. The detection limits were established in the range 23 - 46 ng.mL–1. An inexpensive and harmless method for the simultaneous detection of MEL, CYA, AML, and AMD was developed and may be further applied to the quantification in foods.展开更多
A simple, rapid, and reproducible method is described employing solid phase extraction(SPE) using dichloromethane followed by gas chromatography(GC) with flame ionization detection(FID) for determination of volatile ...A simple, rapid, and reproducible method is described employing solid phase extraction(SPE) using dichloromethane followed by gas chromatography(GC) with flame ionization detection(FID) for determination of volatile organic compound(VOC) from the Buriganga River water of Bangladesh. The method was applied to detect the benzene, toluene, ethylbenzene, xylene and cumene(BTEXC) in the sample collected from the surface or 15 cm depth of water. Two hundred ml of n hexane pretreated and filtered water samples were applied directly to a C 18 SPE column. BTEXC were extracted with dichloromethane and average concentrations were obtained as 0 104 to 0 372 μg/ml. The highest concentration of benzene was found as 0 372 μg/ml with a relative standard deviation(RSD) of 6 2%, and cumene was not detected. Factors influencing SPE e.g., adsorbent types, sample load volume, eluting solvent, headspace and temperatures, were investigated. A cartridge containing a C 18 adsorbent and using dichloromethane gave better performance for extraction of BTEXC from water. Average recoveries exceeding 90% could be achieved for cumene at 4℃ with a 2 7% RSD.展开更多
Polyethersulfone(PES)film with regular microporous structure was formed using dichloromethane as the solvent via water vapor induced phase separation(VIPS).The effects of solution concentration,atmospheric humidity an...Polyethersulfone(PES)film with regular microporous structure was formed using dichloromethane as the solvent via water vapor induced phase separation(VIPS).The effects of solution concentration,atmospheric humidity and temperature,as well as molecular weight of PES on the surface morphology of the polymer film were investigated.The surface morphology characterized by SEM showed that the pore size reduced as the solution concentration increased.There was an optimum range of relative humidity for the formation of regular pore structure, which was from 60%to 90%at concentration of 20 g·L-1 and 20°C.With the atmospheric temperature varied from 20 to 30°C,the pore became larger and the space between pores increased.The pore size in the PES film with low molecular weight was smaller than that with high molecular weight.展开更多
The China Advanced Research Reactor (CARR) is scheduled to be operated in the autumn of 2008.In this paper,we report preparations for installing the neutron radiography instrument (NRI) and for utilizing it efficientl...The China Advanced Research Reactor (CARR) is scheduled to be operated in the autumn of 2008.In this paper,we report preparations for installing the neutron radiography instrument (NRI) and for utilizing it efficiently. The 2-D relative neutron intensity profiles for the water-vapor two-phase flow inside the robe were obtained using the MCNP code without influence of y-ray and electronic-noise.The MCNP simulation of the 2-D neutron intensity profile for the water-vapor two-phase flow was demonstrated.The simulated 2-D neutron intensity profiles could be used as the benchmark data base by calibrating part of the data measured by the CARR-NRI.The 3-D objective images allow us to understand the flow pattern more clearly and it is reconstructed using the MATLAB through the threshold transformation techniques.And thus it is concluded that the MCNP code and the MATLAB are very useful for constructing the benchmark data base for the investigation of the water-vapor two-phase flow using the CARR-NRI.展开更多
Boehmite was prepared under heat treatment in water vapour, and the phase transformation of gibbsite heat-treated at various temperatures was investigated. The sample was characterized by scanning electron microscopy(...Boehmite was prepared under heat treatment in water vapour, and the phase transformation of gibbsite heat-treated at various temperatures was investigated. The sample was characterized by scanning electron microscopy(SEM), X-ray diffraction (XRD), thermogravimetry and differential thermalanalysis (TG-DTA), fourier transform infrared (FTIR),and BET surface area.Effect of temperature on preparation was studied in the range of 155°–195°.With the increase in temperature, transformation of gibbsite into crystalline boehmites took place as indicated by the X-ray diffraction (XRD). The shape of the grains in the prepared sample was cube-like morphology.In water vapour gibbsite transform into boehmite by a dissolution - precipitation mechanism.展开更多
Based on the tensor analysis of water-sediment two-phase how, the basic model equations for clear water flow and sediment-laden flow are deduced in the general curve coordinates for natural water variable-density turb...Based on the tensor analysis of water-sediment two-phase how, the basic model equations for clear water flow and sediment-laden flow are deduced in the general curve coordinates for natural water variable-density turbulent how. Furthermore, corresponding boundary conditions are also presented in connection with the composition and movement of non-uniform bed material. The theoretical results are applied to the calculation of the float open caisson in the construction period and good results are obtained.展开更多
1 Introduction A salt lake is a naturally occurring complex body of water and salt interaction.More than 700 salt lakes are widely distributed in the area of the Qinghai-Tibet Plateau.Most of the salt lakes are famous...1 Introduction A salt lake is a naturally occurring complex body of water and salt interaction.More than 700 salt lakes are widely distributed in the area of the Qinghai-Tibet Plateau.Most of the salt lakes are famous for their abundance of lithium,potassium,magnesium,and boron resources.It is展开更多
This work mainly involved the preparation of a nano-scale form-stable phase change material（PCM） consisting of capric and myristic acid（CA-MA） binary eutectic acting as thermal absorbing material and nano silicon ...This work mainly involved the preparation of a nano-scale form-stable phase change material（PCM） consisting of capric and myristic acid（CA-MA） binary eutectic acting as thermal absorbing material and nano silicon dioxide（nano-SiO_2） serving as the supporting material. Industrial water glass for preparation of the nano silicon dioxide matrix and CA-MA eutectic mixture were compounded by single-step sol-gel method with the silane coupling agent. The morphology, chemical characterization and form stability property of the composite PCM were investigated by transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, Fourier-transform infrared（FT-IR） spectroscopy and polarizing microscopy（POM）. It was indicated that the average diameter of the composite PCM particle ranged from 30-100 nm. The CA-MA eutectic was immobilized in the network pores constructed by the Si-O bonds so that the composite PCM was allowed no liquid leakage above the melting temperature of the CA-MA eutectic. Differential scanning calorimetry（DSC） and thermogravimetric analysis（TGA） measurement were conducted to investigate the thermal properties and stability of the composite PCM. From the measurement results, the mass fraction of the CA-MA eutectic in the composite PCM was about 40%. The phase change temperature and latent heat of the composite were determined to be 21.15 ℃ and 55.67 J/g, respectively. Meanwhile, thermal conductivity of the composite was measured to be 0.208 W·m^（-1）·K^（-1） by using the transient hot-wire method. The composite PCM was able to maintain the surrounding temperature close to its phase change temperature and behaved well in thermalregulated performance which was verified by the heat storage-release experiment. This kind of form-stable PCM was supposed to complete thermal insulation even temperature regulation by the dual effect of relatively low thermal conductivity and phase change thermal storage-release properties. So it can be formulated that the nanoscale CA-MA/SiO_2 composite PCM with the form-stable property, good thermal storage capacity and relatively low thermal conductivity can be applied for energy conservation as a kind of thermal functional material.展开更多
In the absorption chamber of a high-energy laser energy meter, water is directly used as an absorbing medium and the interaction of the high-power laser and the water flow can produce a variety of physical phenomena s...In the absorption chamber of a high-energy laser energy meter, water is directly used as an absorbing medium and the interaction of the high-power laser and the water flow can produce a variety of physical phenomena such as phase transitions. The unit difference method is adopted to deduce the phase transition model for water flow irradiated by a high-energy laser. In addition, the model is simulated and verified through experiments. Among them, the experimental verification uses the photographic method, shooting the distribution and the form of the air mass of water flow in different operating conditions, which are compared with the simulation results. The research shows that it is achievable to reduce the intensity of the phase transition by increasing the water flow, reducing the power intensity of the beam, shortening the distance the beam covers, reducing the initial water temperature or adopting a shorter wavelength laser. The study＇s results will provide the reference for the design of a water-direct-absorption-type high-energy laser energy meter as well as an analysis of the interaction processes of other similar high-power lasers and water flow.展开更多
By means of the computational fluid dynamics software Fluent 6.3, a mathematical model of three-dimensional three-phase fluid flow field in the molten bath of electric arc furnace （EAF） with side accessorial oxygen ...By means of the computational fluid dynamics software Fluent 6.3, a mathematical model of three-dimensional three-phase fluid flow field in the molten bath of electric arc furnace （EAF） with side accessorial oxygen lances was developed to study the transient phenomena of oxygen jet impingement on the molten steel and the molten slag. The water modeling experiment was carried out to verify the simulation results. The impingement of the supersonic oxygen jet caused impact dent on the molten steel surface accordingly. The area of impact dent changed almost in linear relationship to flow rate of oxygen jet, which can be expressed by a deduced mathematical equation. And the relationship between the impact force of oxygen iet and the correspondingly formed apparent static pressure on molten bath was obtained, which was in linear relationship and a direct proportion, and can also be expressed by a deduced mathematical equation.展开更多
The solid–liquid equilibria(SLE)for binary and ternary systems consisting of N-Vinylpyrrolidone(NVP),2-Pyrrolidone(2-P)and water are measured.The phase diagrams of NVP(1)+2-P(2),NVP(1)+water(2),NVP(1)+2-P(2)+1 wt%wat...The solid–liquid equilibria(SLE)for binary and ternary systems consisting of N-Vinylpyrrolidone(NVP),2-Pyrrolidone(2-P)and water are measured.The phase diagrams of NVP(1)+2-P(2),NVP(1)+water(2),NVP(1)+2-P(2)+1 wt%water(3)and NVP(1)+2-P(2)+2 wt%water(3)are identified as simple eutectic type with the eutectic points at 263.75 K(x_(1E)=0.5427),251.65 K(x_(1E)=0.3722),260.25 K(x_(1E)=0.5031)and256.55 K(x_(1E)=0.4684),respectively.The phase diagram of 2-P(1)+water(2)has two eutectic points(x_(1E)=0.1236,T_E=259.15 K and x_(1E)=0.7831,T_E=286.15 K)and one congruent melting point(x_(1C)=0.4997,T_C=303.55 K)because of the generation of a congruently melting addition compound:2-P·H_2O.The ideal solubility and the UNIFAC models were applied to predict the SLE,while the Wilson and NRTL models were employed in correlating the experimental data.The best correlation of the SLE data has been obtained by the Wilson model for the binary system of NVP+2-P.The UNIFAC model gives more satisfactory predictions than the ideal solubility model.展开更多
The microscopic properties of NaCl-induced phase separation of acetonitrile (ACN)-water mixtures have been studied by proton nuclear magnetic resonance (1H NMR). Acetonitrile-rich phase increases with increasing NaCl ...The microscopic properties of NaCl-induced phase separation of acetonitrile (ACN)-water mixtures have been studied by proton nuclear magnetic resonance (1H NMR). Acetonitrile-rich phase increases with increasing NaCl concentration (cNaCl) at xACN ≈ 0.25. 1H chemical shift of water for acetonitrile-rich phase rapidly decreases with decreasing NaCl mole concentration and that for water-rich phase quickly increases with increasing cNaCl. However, 1H chemical shift of acetonitrile has nothing to do with the molar concentration of NaCl, and it keeps relatively stable for all solutions (±0.002). These results reveal that Na+ and Cl- are rapidly hydrated by water, not by acetonitrile. The change of 1H chemical shift of water has shown that the number of hydrogen bond increases or hydrogen bond strengths with increasing NaCl molarity in mixtures. But hydrogen bond is broken or weaken with the temperature rising. 1H chemical shifts of pure water and the water in acetonitrile-rich phase have been investigated at 293 K, 298 K and 303 K. The hydration number of Na+ (6.05) in water-rich phase is determined by an empirical equation involving 1H chemical shift, temperature and NaCl molarity, which is in good agreement with the literatures.展开更多
A novel method was described for the rapid determination of atrazine using dispersive liquid phase microextraction in combination with high performance liquid chromatography （HPLC）. Possible impact parameters such a...A novel method was described for the rapid determination of atrazine using dispersive liquid phase microextraction in combination with high performance liquid chromatography （HPLC）. Possible impact parameters such as sample pH, extraction and disperser solvents, salting-out effect, and extraction time were investigated. The experimental results indicated that proposed method possessed an excellent analytical performance, The linear range, detection limit, and precision （R.S.D.） were 0.1- 50 ng mL- 1 （R2 = 0.9955）, 0.601 ng mL- 1 and 6,4%, respectively. The proposed method was validated with the real water samples, and the spiked recoveries were in the range of 69.9-89.8%, respectively. These results indicated that the established method with high enrichment factor, short extraction time was an excellent alternative for the routine analysis of atrazine in environmental samples. 2007 Qing Xiang Zhou. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.展开更多
基金"111 Project" Biomedical Textile Materials Science and Technology,China
文摘Emulsion electrospinning as a novel process in spinning core-sheath fibers shows a promising potential in drug release control. The volume ratio of water phase to oily phase is one of the critical parameters in forming core-sheath fibers. In this study, water phase was presented by hydrophilic tetracycline hydrochloride and oily phase by hydrophobic poly （E-caprolactone） （PCL）. The effects of volume ratios of water phase to oily phase on fiber morphology and in vitro drug release were investigated. Scanning electron microscopy （ SEM ）, transmission electron microscopy （ TEM）, and eonfoeal laser scanning microscopy（CLSM） were used to observe the morphology, core.sheath structure of the fibers and drug loading in the fibers, respectively. Samples of three different volume ratios of water phase to oily phase, 1： 25, 1：15, and 1：10, were prepared with the same concentration of drug solution. Experiment results showed that, with an increase in the volume ratios of water phase to oily phase, the fiber diameter increased and diameter distribution scattered. The drug entrapment efficiency of the fibers reduces with the increase in volume ratios, L e. , from 73.48 % in the ratio of 1 ： 25, 62.23 % in 1 ： 15, down to 45.63 % in 1：10. In vitro release tests showed that a higher volume ratio of water phase to oily phase would lead to a lower release rate resulted from thicker fiber sheath.
基金supported by the Preventive medicine and public health research project of Anhui,China(No.2011Y0103)the Natural Science Foundation of Anhui,China(No.11040606M216)
文摘To establish an analytical method for determination of four bisphenols （BPA, BPB, BPF, and BPS） and two alkylphenols （4-n-OP, 4-n-NP） in water by ultra performance liquid chromatography- tandem mass spectrometry （UPLC/MS/MS）. The water samples were extracted and condensed with solid-phase extraction （SPE） using C18 cartridges and eluted by acetonitrile. Separation was carried out with Acquity BEH C8 column and detection were performed by UPLC/MS/MS. Quantification was calculated by using the internal standard BPA-d16 and 4-n-NP-d8. The linear correlation coefficients of these compounds in the range of 1.0-100.0μg/L were all over 0.999. The minimum detectable concentrations were 0.75-1.0 ng/L, and the recoveries ranged from 87.0% to 106.9%.
基金Department of Chemistry at Mississippi State University for financial support for this project
文摘An improved method for trace level quantification of dicyandiamide in stream water has been developed. This method includes sample pretreatment using solid phase extraction.The extraction procedure（including loading, washing, and eluting） used a flow rate of1.0 m L/min, and dicyandiamide was eluted with 20 m L of a methanol/acetonitrile mixture（V/V = 2：3）, followed by pre-concentration using nitrogen evaporation and analysis with high performance liquid chromatography–ultraviolet spectroscopy（HPLC–UV）. Sample extraction was carried out using a Waters Sep-Pak AC-2 Cartridge（with activated carbon）.Separation was achieved on a ZIC-Hydrophilic Interaction Liquid Chromatography（ZIC-HILIC）（50 mm × 2.1 mm, 3.5 μm） chromatography column and quantification was accomplished based on UV absorbance. A reliable linear relationship was obtained for the calibration curve using standard solutions（R^2〉 0.999）. Recoveries for dicyandiamide ranged from 84.6% to 96.8%, and the relative standard deviations（RSDs, n = 3） were below 6.1% with a detection limit of 5.0 ng/m L for stream water samples.
基金Supported by the China-Austria Scientific and Technological Cooperative Project of National Science and Technology Ministry of China (CN 01/2007)
文摘In order to simulate the unsteady seepage in soil slopes under water level rise condition, including water seepage and air seepage, and to investigate the influence of the capillary pressure on the slope safety coefficient, the water-air two-phase flow model was used and its solving method and definition condition were given. By the two-phase flow model, the pore air and pore water seepage of a soil slope under steady seepage and water level rise conditions were shown, and the slope stability in different cases was analyzed from the simulation results. We find that under water level rise condition, the pore air pressure in the unsaturated zone increased evidently and the capillary pressure should be considered while the pore air pressure can be neglected in slope stability analysis.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.41174109 and 61104148)the National Science and Technology Major Project of the Ministry of Science and Technology of China(Grant No.2011ZX05020-006)the Tianjin City High School Science and Technology Fund Planning Project,China(Grant No.20130718)
文摘We investigate the dynamic characteristics of oil-gas-water three-phase flow in terms of chaotic attractor comparison. In particular, we extract a statistic to characterize the dynamical difference in attractor probability distribution. We first take time series from Logistic chaotic system with different parameters as examples to demonstrate the effectiveness of the method. Then we use this method to investigate the experimental signals from oil-gas-water three-phase flow. The results indicate that the extracted statistic is very sensitive to the change of flow parameters and can gain a quantitatively insight into the dynamic characteristics of different flow patterns.
文摘This paper developed a fluorometric method for the sensitive determination of nonylphenol in water samples by preconcentration with zirconium doped titanium dioxide nanotubes solid phase extraction.The parameters on extraction that would influence the enrichment performance such as the kind and volume of eluent,sample pH,sample flow rate,and sample volume were optimized in detail.Under the optimal conditions,the proposed method provided an excellent linear range of 1-150 mg/L and good LOD of 0.076 mg/L.The relative standard deviation（RSD,n = 6） was 2.8%.Proposed method was also used for the analysis of real water samples and the spiked recoveries were satisfied in the range of 98.7-103%.
文摘This paper describes a reserved-phase high performance liquid chromatographic method for detecting melamine (MEL) and related analogues, cyanuric acid (CYA), ammeline (AML), and ammelide (AMD), using a 100% water mobile phase. Chromatographic separation was performed an Inertsil? ODS-4 (250 × 4.6 mm, 5 μm) with a water mobile phase and a photodiode-array detector. The monitoring wavelength was adjusted to 210 nm which represents an average maximum for all the analytes. The total run time was < 8 min. The method shows high stability, significant linearity and satisfactory sensitivity. The detection limits were established in the range 23 - 46 ng.mL–1. An inexpensive and harmless method for the simultaneous detection of MEL, CYA, AML, and AMD was developed and may be further applied to the quantification in foods.
文摘A simple, rapid, and reproducible method is described employing solid phase extraction(SPE) using dichloromethane followed by gas chromatography(GC) with flame ionization detection(FID) for determination of volatile organic compound(VOC) from the Buriganga River water of Bangladesh. The method was applied to detect the benzene, toluene, ethylbenzene, xylene and cumene(BTEXC) in the sample collected from the surface or 15 cm depth of water. Two hundred ml of n hexane pretreated and filtered water samples were applied directly to a C 18 SPE column. BTEXC were extracted with dichloromethane and average concentrations were obtained as 0 104 to 0 372 μg/ml. The highest concentration of benzene was found as 0 372 μg/ml with a relative standard deviation(RSD) of 6 2%, and cumene was not detected. Factors influencing SPE e.g., adsorbent types, sample load volume, eluting solvent, headspace and temperatures, were investigated. A cartridge containing a C 18 adsorbent and using dichloromethane gave better performance for extraction of BTEXC from water. Average recoveries exceeding 90% could be achieved for cumene at 4℃ with a 2 7% RSD.
基金Supported by the National Natural Science Foundation of China （20676015, 20806009）, and the Specialized Research Fund for the Doctoral Program of Higher Education of China （20070007055）.
文摘Polyethersulfone(PES)film with regular microporous structure was formed using dichloromethane as the solvent via water vapor induced phase separation(VIPS).The effects of solution concentration,atmospheric humidity and temperature,as well as molecular weight of PES on the surface morphology of the polymer film were investigated.The surface morphology characterized by SEM showed that the pore size reduced as the solution concentration increased.There was an optimum range of relative humidity for the formation of regular pore structure, which was from 60%to 90%at concentration of 20 g·L-1 and 20°C.With the atmospheric temperature varied from 20 to 30°C,the pore became larger and the space between pores increased.The pore size in the PES film with low molecular weight was smaller than that with high molecular weight.
基金Supported by National Natural Science Foundation of China (Grant No.50876080)
文摘The China Advanced Research Reactor (CARR) is scheduled to be operated in the autumn of 2008.In this paper,we report preparations for installing the neutron radiography instrument (NRI) and for utilizing it efficiently. The 2-D relative neutron intensity profiles for the water-vapor two-phase flow inside the robe were obtained using the MCNP code without influence of y-ray and electronic-noise.The MCNP simulation of the 2-D neutron intensity profile for the water-vapor two-phase flow was demonstrated.The simulated 2-D neutron intensity profiles could be used as the benchmark data base by calibrating part of the data measured by the CARR-NRI.The 3-D objective images allow us to understand the flow pattern more clearly and it is reconstructed using the MATLAB through the threshold transformation techniques.And thus it is concluded that the MCNP code and the MATLAB are very useful for constructing the benchmark data base for the investigation of the water-vapor two-phase flow using the CARR-NRI.
文摘Boehmite was prepared under heat treatment in water vapour, and the phase transformation of gibbsite heat-treated at various temperatures was investigated. The sample was characterized by scanning electron microscopy(SEM), X-ray diffraction (XRD), thermogravimetry and differential thermalanalysis (TG-DTA), fourier transform infrared (FTIR),and BET surface area.Effect of temperature on preparation was studied in the range of 155°–195°.With the increase in temperature, transformation of gibbsite into crystalline boehmites took place as indicated by the X-ray diffraction (XRD). The shape of the grains in the prepared sample was cube-like morphology.In water vapour gibbsite transform into boehmite by a dissolution - precipitation mechanism.
文摘Based on the tensor analysis of water-sediment two-phase how, the basic model equations for clear water flow and sediment-laden flow are deduced in the general curve coordinates for natural water variable-density turbulent how. Furthermore, corresponding boundary conditions are also presented in connection with the composition and movement of non-uniform bed material. The theoretical results are applied to the calculation of the float open caisson in the construction period and good results are obtained.
基金Financial supports from the NSFCs (21106103, 21276194 and 21306136)the Specialized Research Funds for the Doctoral Program of Chinese Higher Education (20101208110003 and 20111208120003)+1 种基金the Natural Science Foundation of Tianjin (12JCQNJC03400)the Senior Professor Program for TUST (20100405)
文摘1 Introduction A salt lake is a naturally occurring complex body of water and salt interaction.More than 700 salt lakes are widely distributed in the area of the Qinghai-Tibet Plateau.Most of the salt lakes are famous for their abundance of lithium,potassium,magnesium,and boron resources.It is
基金Funded by the National Natural Science Foundation of China(No.51308275)Natural Science Foundation of Liaoning Province(No.SY2016004)the Colleges and Universities Excellent Talents Supporting Plan Program of Liaoning Province(No.LJQ2015049)
文摘This work mainly involved the preparation of a nano-scale form-stable phase change material（PCM） consisting of capric and myristic acid（CA-MA） binary eutectic acting as thermal absorbing material and nano silicon dioxide（nano-SiO_2） serving as the supporting material. Industrial water glass for preparation of the nano silicon dioxide matrix and CA-MA eutectic mixture were compounded by single-step sol-gel method with the silane coupling agent. The morphology, chemical characterization and form stability property of the composite PCM were investigated by transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, Fourier-transform infrared（FT-IR） spectroscopy and polarizing microscopy（POM）. It was indicated that the average diameter of the composite PCM particle ranged from 30-100 nm. The CA-MA eutectic was immobilized in the network pores constructed by the Si-O bonds so that the composite PCM was allowed no liquid leakage above the melting temperature of the CA-MA eutectic. Differential scanning calorimetry（DSC） and thermogravimetric analysis（TGA） measurement were conducted to investigate the thermal properties and stability of the composite PCM. From the measurement results, the mass fraction of the CA-MA eutectic in the composite PCM was about 40%. The phase change temperature and latent heat of the composite were determined to be 21.15 ℃ and 55.67 J/g, respectively. Meanwhile, thermal conductivity of the composite was measured to be 0.208 W·m^（-1）·K^（-1） by using the transient hot-wire method. The composite PCM was able to maintain the surrounding temperature close to its phase change temperature and behaved well in thermalregulated performance which was verified by the heat storage-release experiment. This kind of form-stable PCM was supposed to complete thermal insulation even temperature regulation by the dual effect of relatively low thermal conductivity and phase change thermal storage-release properties. So it can be formulated that the nanoscale CA-MA/SiO_2 composite PCM with the form-stable property, good thermal storage capacity and relatively low thermal conductivity can be applied for energy conservation as a kind of thermal functional material.
文摘In the absorption chamber of a high-energy laser energy meter, water is directly used as an absorbing medium and the interaction of the high-power laser and the water flow can produce a variety of physical phenomena such as phase transitions. The unit difference method is adopted to deduce the phase transition model for water flow irradiated by a high-energy laser. In addition, the model is simulated and verified through experiments. Among them, the experimental verification uses the photographic method, shooting the distribution and the form of the air mass of water flow in different operating conditions, which are compared with the simulation results. The research shows that it is achievable to reduce the intensity of the phase transition by increasing the water flow, reducing the power intensity of the beam, shortening the distance the beam covers, reducing the initial water temperature or adopting a shorter wavelength laser. The study＇s results will provide the reference for the design of a water-direct-absorption-type high-energy laser energy meter as well as an analysis of the interaction processes of other similar high-power lasers and water flow.
基金Sponsored by National Key Technology Research and Development Program in 11th Five-year Plan of China(2008AF33B01)Fuzhou University Foundation for Development of Science and Technology of China(0020-600588)
文摘By means of the computational fluid dynamics software Fluent 6.3, a mathematical model of three-dimensional three-phase fluid flow field in the molten bath of electric arc furnace （EAF） with side accessorial oxygen lances was developed to study the transient phenomena of oxygen jet impingement on the molten steel and the molten slag. The water modeling experiment was carried out to verify the simulation results. The impingement of the supersonic oxygen jet caused impact dent on the molten steel surface accordingly. The area of impact dent changed almost in linear relationship to flow rate of oxygen jet, which can be expressed by a deduced mathematical equation. And the relationship between the impact force of oxygen iet and the correspondingly formed apparent static pressure on molten bath was obtained, which was in linear relationship and a direct proportion, and can also be expressed by a deduced mathematical equation.
文摘The solid–liquid equilibria(SLE)for binary and ternary systems consisting of N-Vinylpyrrolidone(NVP),2-Pyrrolidone(2-P)and water are measured.The phase diagrams of NVP(1)+2-P(2),NVP(1)+water(2),NVP(1)+2-P(2)+1 wt%water(3)and NVP(1)+2-P(2)+2 wt%water(3)are identified as simple eutectic type with the eutectic points at 263.75 K(x_(1E)=0.5427),251.65 K(x_(1E)=0.3722),260.25 K(x_(1E)=0.5031)and256.55 K(x_(1E)=0.4684),respectively.The phase diagram of 2-P(1)+water(2)has two eutectic points(x_(1E)=0.1236,T_E=259.15 K and x_(1E)=0.7831,T_E=286.15 K)and one congruent melting point(x_(1C)=0.4997,T_C=303.55 K)because of the generation of a congruently melting addition compound:2-P·H_2O.The ideal solubility and the UNIFAC models were applied to predict the SLE,while the Wilson and NRTL models were employed in correlating the experimental data.The best correlation of the SLE data has been obtained by the Wilson model for the binary system of NVP+2-P.The UNIFAC model gives more satisfactory predictions than the ideal solubility model.
文摘The microscopic properties of NaCl-induced phase separation of acetonitrile (ACN)-water mixtures have been studied by proton nuclear magnetic resonance (1H NMR). Acetonitrile-rich phase increases with increasing NaCl concentration (cNaCl) at xACN ≈ 0.25. 1H chemical shift of water for acetonitrile-rich phase rapidly decreases with decreasing NaCl mole concentration and that for water-rich phase quickly increases with increasing cNaCl. However, 1H chemical shift of acetonitrile has nothing to do with the molar concentration of NaCl, and it keeps relatively stable for all solutions (±0.002). These results reveal that Na+ and Cl- are rapidly hydrated by water, not by acetonitrile. The change of 1H chemical shift of water has shown that the number of hydrogen bond increases or hydrogen bond strengths with increasing NaCl molarity in mixtures. But hydrogen bond is broken or weaken with the temperature rising. 1H chemical shifts of pure water and the water in acetonitrile-rich phase have been investigated at 293 K, 298 K and 303 K. The hydration number of Na+ (6.05) in water-rich phase is determined by an empirical equation involving 1H chemical shift, temperature and NaCl molarity, which is in good agreement with the literatures.
基金This work was supported by the Personal Innovation Foundation of Universities in Henan Province （No. [2005] 126）； Natural Science Foundation of Henan Province （No. 072300460010） ；the Fund of Henan Normal University （No, 2006PL06）； the grants from the Henan Key Laboratory for environmental pollution control.
文摘A novel method was described for the rapid determination of atrazine using dispersive liquid phase microextraction in combination with high performance liquid chromatography （HPLC）. Possible impact parameters such as sample pH, extraction and disperser solvents, salting-out effect, and extraction time were investigated. The experimental results indicated that proposed method possessed an excellent analytical performance, The linear range, detection limit, and precision （R.S.D.） were 0.1- 50 ng mL- 1 （R2 = 0.9955）, 0.601 ng mL- 1 and 6,4%, respectively. The proposed method was validated with the real water samples, and the spiked recoveries were in the range of 69.9-89.8%, respectively. These results indicated that the established method with high enrichment factor, short extraction time was an excellent alternative for the routine analysis of atrazine in environmental samples. 2007 Qing Xiang Zhou. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.
