The Mg–Zn–Y–Zr alloys with long-period stacking-ordered(LPSO)and W eutectic phases were investigated to develop new magnesium casting alloys.The temperatures for T6 heat treatment were selected based on the hardnes...The Mg–Zn–Y–Zr alloys with long-period stacking-ordered(LPSO)and W eutectic phases were investigated to develop new magnesium casting alloys.The temperatures for T6 heat treatment were selected based on the hardness and electrical conductivity measurements.The hot tearing susceptibility of the alloys with LPSO phase is lower than that of the alloys with W phase,which is associated with the freezing range of the alloys.However,the investigated alloys displayed the same fluidity.Under T6 conditions,increasing the Y content in the alloys resulted in increased yield strength,whereas other tensile properties were similar for the alloys.The corrosion resistance was higher for the alloys with LPSO phase compared to that of the alloys with W phase.Mg−2.5Zn−3.7Y−0.3Zr(mass fraction,%)alloy with LPSO phase possessed high castability and mechanical properties,with a corrosion rate of 2 mm/year.展开更多
A high strength Mg-5.1Zn-3.2Y-0.4Zr-0.4Ca （wt%） alloy containing W phase （Mg3Y2Zn3） prepared by permanent mold direct-chill casting is indirectly extruded at 350 ℃ and 400 ℃, respectively. The extruded alloys sh...A high strength Mg-5.1Zn-3.2Y-0.4Zr-0.4Ca （wt%） alloy containing W phase （Mg3Y2Zn3） prepared by permanent mold direct-chill casting is indirectly extruded at 350 ℃ and 400 ℃, respectively. The extruded alloys show bimodal grain structure consisting of fine dynamic recrystallized （DRXed） grains and unre- crystallized coarse regions containing fine W phase and β2′ precipitates. The fragmented W phase particles induced by extrusion stimulate nucleation of DRXed grains, leading to the formation of fine DRXed grains, which are mainly distributed near the W particle bands along the extrusion direction. The alloy extruded at 350 ℃ exhibits yield strength of 373 MPa, ultimate tensile strength of 403 MPa and elongation to failure of 5.1%. While the alloy extruded at 400 ℃ shows lower yield strength of 332 MPa, ultimate tensile strength of 352 MPa and higher elongation to failure of 12%. The mechanical properties of the as-extruded alloys vary with the distribution and size of W phase. A higher fraction of DRXed grains is obtained due to the homogeneous distribution of micron-scale broken W phase particles in the alloy extruded at 400 ℃, which can lead to higher ductility. In addition, the nano-scale dynamic W phase precipitates distributed in the unDRXed regions are refined at lower extrusion temperature. The smaller size of nano-scale W phase precipitates leads to a higher fraction of unDRXed regions which contributes to higher strength of the alloy extruded at 350 ℃.展开更多
The microstructure evolution of Mg100-2xYxZnx （x=2, 2.5, 3, 3.5） alloys was investigated. Results show that the Mg100-2xYxZnx alloys are composed of a-Mg, long period stacking ordered （LPSO） phase and eutectic str...The microstructure evolution of Mg100-2xYxZnx （x=2, 2.5, 3, 3.5） alloys was investigated. Results show that the Mg100-2xYxZnx alloys are composed of a-Mg, long period stacking ordered （LPSO） phase and eutectic structure phase （W phase）, and the Mg95Y2.5Zn2.5 alloy has the best comprehensive mechanical properties. Subsequently, the microstructure evolution of the optimized alloy Mg95Y2.5Zn2.5 during solidification and heat treatment processes was analyzed and discussed by means of OM, SEM, TEM, XRD and DTA. After heat treatment, the lamellar phase 14H-LPSO precipitated in a-Mg and W phase transforms into particle phase （MgyZn2）. Due to the compound reinforcement effect of the particle phase and LPSO phase （18R＋14H）, the mechanical properties of the alloy are enhanced. The tensile strength and elongation of the Mg95Y2.5Zn2.5 alloy is improved by 9.1% and 31.3% to 215 MPa and 10.5%, respectively, after solid-solution treatment.展开更多
This study was aimed at identifying underlying strengthening mechanisms and predicting the yield strength of as-extruded Mg-Zn-Y alloys with varying amounts of yttrium （Y） element. The addition of Y resulted in the ...This study was aimed at identifying underlying strengthening mechanisms and predicting the yield strength of as-extruded Mg-Zn-Y alloys with varying amounts of yttrium （Y） element. The addition of Y resulted in the formation of ternary 1 （Mg3YZn6）, W （Mg3Y2Zn3） and LPSO （Mg12YZn） phases which subse- quently reinforced alloys ZM31 ＋ 0.3Y, ZM31 ＋ 3.2Y and ZM31 ＋ 6Y, where the value denoted the amount of Y element （in wt%）. Yield strength of the alloys was determined via uniaxial compression testing, and grain size and second-phase particles were characterized using OM and SEM. In-situ high-temperature XRD was performed to determine the coefficient of thermal expansion （CTE）, which was derived to be 1.38 x 10^-5 K^-1 and 2.35 x 10^-5 K^-1 for W and LPSO phases, respectively. The individual strengthening effects in each material were quantified for the first time, including grain refinement, Orowan looping, thermal mismatch, dislocation density, load-bearing, and particle shearing contributions. Grain refinement was one of the major strengthening mechanisms and it was present in all the alloys studied, irrespective of the second-phase particles. Orowan looping and crE mismatch were the predominant strengthening mechanisms in the ZM31＋0.3Y and ZM31 ＋ 3.2Y alloys containing I and W phases, respectively, while load-bearing and second-phase shearing were the salient mechanisms contributing largely to the superior yield strength of the LPSO-reinforced ZM31 ＋ 6Y alloy.2017 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science ＆ Technology.展开更多
In this study,Al-30W(wt.%)alloy powder was prepared by Aluminothermic reduction and hightemperature gas atomization.We then studied the phase composition,surface morphology,spatial phase structure,and thermal oxidatio...In this study,Al-30W(wt.%)alloy powder was prepared by Aluminothermic reduction and hightemperature gas atomization.We then studied the phase composition,surface morphology,spatial phase structure,and thermal oxidation process using XRD,SEM/EDS,TEM,DSC,and DTA/TG analysis.The results showed that the Al-30W alloy powder exhibited high sphericity,and the interior presented a special spatial phase structure in which the Al/W amorphous alloy phase and the metastable Al/W intermetallic compound phase were distributed in the pure Al matrix.When the Al-30W alloy powder was stabilized in a vacuum tube furnace,the spatial phase structure of the alloy powder changed,and a small amount of pure Al was embedded in the Al_(12)W matrix.The resulting Al-30W alloy powder products,treated in air at different temperatures,were collected in situ and characterized.The results presented that with an increase in temperature,the types and morphologies of the Al/W intermetallic compounds in the Al-30W alloy powder changed.Furthermore,the Al-30W alloy powder began to undergo intense oxidation reactions at about 900℃,accompanied by a concentrated energy release and rapid weight gain.The volatilization of WO_(3)produced in the oxidation process promoted the complete oxidation of the Al-30W alloy powder,and the Al-30W alloy powder was completely oxidized at 1300℃.At this stage,all W atoms were transformed into gaseous WO_(3),and only a large number of small Al_(2)O_(3)fragments remained in the oxidation product.Thus,the Al-30W alloy powder exhibited excellent thermal reactivity and oxidation integrity,and may offer excellent application prospects in the field of energetic materials.展开更多
The spheroidizing mechanism of W-phase in the Mg–Zn–Y–Mn–（B） alloys during solid-solution treatment was investigated by using kinetic methodologies. The microstructure and mechanical properties of heat-treated ...The spheroidizing mechanism of W-phase in the Mg–Zn–Y–Mn–（B） alloys during solid-solution treatment was investigated by using kinetic methodologies. The microstructure and mechanical properties of heat-treated Mg_（94）Zn_（2.5）-Y_（2.5）Mn_1 alloy containing 0.003 wt% B were compared with heat-treated Mg_（94）Zn_（2.5）-Y_（2.5）Mn_1 alloy. The heat-treated Mg_（94）Zn_（2.5）-Y_（2.5）Mn_1 alloy with 0.003 wt% B contained fine and uniform W-phase particles, which exhibited optimal mechanical performance. The ultimate tensile strength, yield strength and elongation were 287.7, 125.5 MPa and 21.1%,respectively.展开更多
The characteristic crystal model is applied to the study of phase stability and thermodynamics in substitutional bcc-based Ta-W alloys.The basic principle and method of alloy thermodynamics which is described by the c...The characteristic crystal model is applied to the study of phase stability and thermodynamics in substitutional bcc-based Ta-W alloys.The basic principle and method of alloy thermodynamics which is described by the characteristic crystal model is introduced in detail.The Gibbs energy of various phases including both disordered and ordered phases of the Ta-W system are evaluated.The phase diagram of Ta-W alloys is assessed and predicted.The results are in good agreement with experiments and better than that of first principle.展开更多
Powder metallurgic Ti2 AlNb alloys with W addition are sintered at 900, 1000, 1070 °C,and 1150 °C(i.e., in the O + B2, a_2+ B2 + O, a_2+ B2, and single B2 phase regions, respectively)for 12 h, followed by wa...Powder metallurgic Ti2 AlNb alloys with W addition are sintered at 900, 1000, 1070 °C,and 1150 °C(i.e., in the O + B2, a_2+ B2 + O, a_2+ B2, and single B2 phase regions, respectively)for 12 h, followed by water quenching and furnace cooling. Comparisons of phase and microstructure between quenched and furnace-cooled W-modified alloys are carried out to illustrate the phase transformation and microstructure evolution during the cooling process. Furthermore, a comparison is also made between W-modified and W-free alloys, to reveal the function of the W alloying.W addition accelerates the solutions of a_2 and O phases during the high-temperature holding, and a Widmannsta¨tten B2 + O structure, which contributes to the properties, is induced by furnace cooling from all the phase regions. The Widmannsta¨tten structure includes a B2 matrix, primary O, and secondary O precipitates. However, W alloying refines the Widmannsta¨tten structure only when the alloys are solution-treated and then cooled from the single B2 phase. Although the hardness of the W-modified alloys is lower than that of the W-free alloys sintered in the same phase region, an enhancement of hardness, 489 ± 18 HV, is obtained in the alloy solution-treated in the single B2 phase region for only 0.5 h.展开更多
The kinetic characteristics of W grain growth operated by diffusion controlled Oswald ripening （DOR） during liquid phase sintering were studied. A liquid phase sintering of W-15wt%Cu was carried out by pushing compa...The kinetic characteristics of W grain growth operated by diffusion controlled Oswald ripening （DOR） during liquid phase sintering were studied. A liquid phase sintering of W-15wt%Cu was carried out by pushing compacts into a furnace at the moment when the temperature increased to 1340℃ for different sintering times. The results show that liquid phase sintering produces the compacts with considerably low relative density and inversely, rather high homogeneity. On the basis of the data extracted from the SEM images, the kinetic equation of W grain growth, G^n = G0^n ＋ kt, is determined in which the grain growth exponent n is 3 and the grain growth rate constant k is 0.15 μm^3/s. The cumulative normalized grain size distributions produced by different sintering times show self-similar. The cumulative distribution function is extracted from the curves by non-linear fitting. In addition, the sintering kinetic characteristics of W-15wt%Cu compacts were also investigated.展开更多
A new tungsten heavy alloy, W-Ni-Fe-TiB_2 was studied. This ally has higher hardness than tradition-al tungsten heavy alloy. Sintering time was 30 min for producing the alloy. In the new tungsten heavy alloy, four pha...A new tungsten heavy alloy, W-Ni-Fe-TiB_2 was studied. This ally has higher hardness than tradition-al tungsten heavy alloy. Sintering time was 30 min for producing the alloy. In the new tungsten heavy alloy, four phases were found to be W, γ (Ni, Fe), TiB_2 and complex haride compound. TiB_2 and complexboride compound were precipitated in the matrix. So TiB_2 could strengthen the tungsten heavy alloy.展开更多
The precipitation behaviour of Fe-Cr-Mo and Fe-Cr-W alloys during aging has been ex- perimentally studied.It was found that in the early stage of aging,a metastable R phase pre- cipitated in both alloys,it was transfo...The precipitation behaviour of Fe-Cr-Mo and Fe-Cr-W alloys during aging has been ex- perimentally studied.It was found that in the early stage of aging,a metastable R phase pre- cipitated in both alloys,it was transformed into stable μ-phase,Laves-phase,X-phase or σ-phase in the later stages.The crystallographic structure of metastable R-phase is rhombohedral with lattice parameters of a=0.9075 nm and α=74.45°.The chemical compo- sition of R-phase is Fe-(27.5—34.9)Mo-(0—25.5)Cr and Fe-(28.9—33.0)W-(9.36— 21.0)Cr in at.-% in Fe-Cr-Mo and Fe-Cr-W system,respectively.展开更多
Phase stability of four different chemical component Fe-Cr-Mn(W, V) alloys are investigated by experimental method and thermodynamic model in this paper. It is indicated that the main phase of four alloys after aged u...Phase stability of four different chemical component Fe-Cr-Mn(W, V) alloys are investigated by experimental method and thermodynamic model in this paper. It is indicated that the main phase of four alloys after aged under 623, 673, 773K for 200h are austenitic phase. The results of Thermo-Calc, which are based on Gibbs energy, show that the phases of four alloys under ihe same temperature as experimental method are single austenitic phase. The results of experimental method and Thermo-Calc agree well.展开更多
Pure W and W-Cu-W trilayer coatings were deposited on an Fe substrate by d.c. magnetron sputtering. The α-β phase evolution, intragranular stress evolution in sputter-deposited W layer were investigated by x-ray dif...Pure W and W-Cu-W trilayer coatings were deposited on an Fe substrate by d.c. magnetron sputtering. The α-β phase evolution, intragranular stress evolution in sputter-deposited W layer were investigated by x-ray diffraction. They are directly related to the film microstructure, density and adhesion. Therefore, control of the film stress and phase component transition is essential for its applications. The phase component transition from β-W to α-W and intragranular stress evolution from tensile to compressive strongly depend on the deposition parameters and can be induced by lowering Ar pressure and rising target power. The compressively stressed films with α-W phase have a dense microstructure and high adhesion to Fe substrate.展开更多
本文采用最新文献报道的Ni-Cr、Ni-W和Cr-W二元热力学参数,结合Ni-Cr-W三元体系实验数据,使用相图计算(calculation of phase diagram,CALPHAD)方法进行热力学评估和优化计算,获得了一套自洽的热力学参数,其中σ相的热力学模型为亚点阵...本文采用最新文献报道的Ni-Cr、Ni-W和Cr-W二元热力学参数,结合Ni-Cr-W三元体系实验数据,使用相图计算(calculation of phase diagram,CALPHAD)方法进行热力学评估和优化计算,获得了一套自洽的热力学参数,其中σ相的热力学模型为亚点阵模型:(Cr,Ni,W)_(0.533)(Cr,Ni,W)_(0.333)(Cr,Ni,W)_(0.134)。计算的Ni-Cr-W体系等温截面图(1273、1473、1673和1813 K)和液相面投影图与实验数据匹配较好,说明本工作的热力学数据库能够很好地再现实验结果,对此体系相关的高元合金设计具有参考意义。展开更多
基金the Ministry of Science and Higher Education of the Russian Federation in the framework of Increase Competitiveness Program of NUST«MISiS»(No.К2-2020-025),implemented by a governmental decree dated 16th of March 2013,N 211.
文摘The Mg–Zn–Y–Zr alloys with long-period stacking-ordered(LPSO)and W eutectic phases were investigated to develop new magnesium casting alloys.The temperatures for T6 heat treatment were selected based on the hardness and electrical conductivity measurements.The hot tearing susceptibility of the alloys with LPSO phase is lower than that of the alloys with W phase,which is associated with the freezing range of the alloys.However,the investigated alloys displayed the same fluidity.Under T6 conditions,increasing the Y content in the alloys resulted in increased yield strength,whereas other tensile properties were similar for the alloys.The corrosion resistance was higher for the alloys with LPSO phase compared to that of the alloys with W phase.Mg−2.5Zn−3.7Y−0.3Zr(mass fraction,%)alloy with LPSO phase possessed high castability and mechanical properties,with a corrosion rate of 2 mm/year.
基金supported financially by the National Key Research and Development Program of China (No. 2016YFB0301102)the National Natural Science Foundation of China (No. 51571068)
文摘A high strength Mg-5.1Zn-3.2Y-0.4Zr-0.4Ca （wt%） alloy containing W phase （Mg3Y2Zn3） prepared by permanent mold direct-chill casting is indirectly extruded at 350 ℃ and 400 ℃, respectively. The extruded alloys show bimodal grain structure consisting of fine dynamic recrystallized （DRXed） grains and unre- crystallized coarse regions containing fine W phase and β2′ precipitates. The fragmented W phase particles induced by extrusion stimulate nucleation of DRXed grains, leading to the formation of fine DRXed grains, which are mainly distributed near the W particle bands along the extrusion direction. The alloy extruded at 350 ℃ exhibits yield strength of 373 MPa, ultimate tensile strength of 403 MPa and elongation to failure of 5.1%. While the alloy extruded at 400 ℃ shows lower yield strength of 332 MPa, ultimate tensile strength of 352 MPa and higher elongation to failure of 12%. The mechanical properties of the as-extruded alloys vary with the distribution and size of W phase. A higher fraction of DRXed grains is obtained due to the homogeneous distribution of micron-scale broken W phase particles in the alloy extruded at 400 ℃, which can lead to higher ductility. In addition, the nano-scale dynamic W phase precipitates distributed in the unDRXed regions are refined at lower extrusion temperature. The smaller size of nano-scale W phase precipitates leads to a higher fraction of unDRXed regions which contributes to higher strength of the alloy extruded at 350 ℃.
基金financially supported by the National Natural Science Foundation of China(Nos.50571073,51574175 and 51474153)Ph.D.Programs Foundation of Ministry of Education of China(20111402110004)Natural Science Foundation of Shanxi Province(Nos.2009011028-3 and 2012011022-1)
文摘The microstructure evolution of Mg100-2xYxZnx （x=2, 2.5, 3, 3.5） alloys was investigated. Results show that the Mg100-2xYxZnx alloys are composed of a-Mg, long period stacking ordered （LPSO） phase and eutectic structure phase （W phase）, and the Mg95Y2.5Zn2.5 alloy has the best comprehensive mechanical properties. Subsequently, the microstructure evolution of the optimized alloy Mg95Y2.5Zn2.5 during solidification and heat treatment processes was analyzed and discussed by means of OM, SEM, TEM, XRD and DTA. After heat treatment, the lamellar phase 14H-LPSO precipitated in a-Mg and W phase transforms into particle phase （MgyZn2）. Due to the compound reinforcement effect of the particle phase and LPSO phase （18R＋14H）, the mechanical properties of the alloy are enhanced. The tensile strength and elongation of the Mg95Y2.5Zn2.5 alloy is improved by 9.1% and 31.3% to 215 MPa and 10.5%, respectively, after solid-solution treatment.
基金the Natural Sciences and Engineering Research Council of Canada (NSERC)Ontario Trillium Scholarships (OTS) program for providing financial support+8 种基金financial support by the Premier’s Research Excellence Award (PREA)Canada Foundation for Innovation (CFI)Ryerson Research Chair (RRC) programthe Ministry of Science and Technology of China (2014DFG52810)National Great Theoretic Research Project of China (2013CB632200)National Natural Science Foundation of China (Project 51474043)Ministry of Education of China (SRFDR 20130191110018)Chongqing Municipal Government(CSTC2013JCYJC60001)Chongqing Science and Technology Commission (CSTC2011gjhz50001)
文摘This study was aimed at identifying underlying strengthening mechanisms and predicting the yield strength of as-extruded Mg-Zn-Y alloys with varying amounts of yttrium （Y） element. The addition of Y resulted in the formation of ternary 1 （Mg3YZn6）, W （Mg3Y2Zn3） and LPSO （Mg12YZn） phases which subse- quently reinforced alloys ZM31 ＋ 0.3Y, ZM31 ＋ 3.2Y and ZM31 ＋ 6Y, where the value denoted the amount of Y element （in wt%）. Yield strength of the alloys was determined via uniaxial compression testing, and grain size and second-phase particles were characterized using OM and SEM. In-situ high-temperature XRD was performed to determine the coefficient of thermal expansion （CTE）, which was derived to be 1.38 x 10^-5 K^-1 and 2.35 x 10^-5 K^-1 for W and LPSO phases, respectively. The individual strengthening effects in each material were quantified for the first time, including grain refinement, Orowan looping, thermal mismatch, dislocation density, load-bearing, and particle shearing contributions. Grain refinement was one of the major strengthening mechanisms and it was present in all the alloys studied, irrespective of the second-phase particles. Orowan looping and crE mismatch were the predominant strengthening mechanisms in the ZM31＋0.3Y and ZM31 ＋ 3.2Y alloys containing I and W phases, respectively, while load-bearing and second-phase shearing were the salient mechanisms contributing largely to the superior yield strength of the LPSO-reinforced ZM31 ＋ 6Y alloy.2017 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science ＆ Technology.
基金supported by the National Natural Science Foundation of China(No.51871106).We express our grat-itude for analyzing and testing of Huazhong University of Science and Technology Analytical&Testing Center.
文摘In this study,Al-30W(wt.%)alloy powder was prepared by Aluminothermic reduction and hightemperature gas atomization.We then studied the phase composition,surface morphology,spatial phase structure,and thermal oxidation process using XRD,SEM/EDS,TEM,DSC,and DTA/TG analysis.The results showed that the Al-30W alloy powder exhibited high sphericity,and the interior presented a special spatial phase structure in which the Al/W amorphous alloy phase and the metastable Al/W intermetallic compound phase were distributed in the pure Al matrix.When the Al-30W alloy powder was stabilized in a vacuum tube furnace,the spatial phase structure of the alloy powder changed,and a small amount of pure Al was embedded in the Al_(12)W matrix.The resulting Al-30W alloy powder products,treated in air at different temperatures,were collected in situ and characterized.The results presented that with an increase in temperature,the types and morphologies of the Al/W intermetallic compounds in the Al-30W alloy powder changed.Furthermore,the Al-30W alloy powder began to undergo intense oxidation reactions at about 900℃,accompanied by a concentrated energy release and rapid weight gain.The volatilization of WO_(3)produced in the oxidation process promoted the complete oxidation of the Al-30W alloy powder,and the Al-30W alloy powder was completely oxidized at 1300℃.At this stage,all W atoms were transformed into gaseous WO_(3),and only a large number of small Al_(2)O_(3)fragments remained in the oxidation product.Thus,the Al-30W alloy powder exhibited excellent thermal reactivity and oxidation integrity,and may offer excellent application prospects in the field of energetic materials.
基金support from the National Natural Science Foundation of China(Nos.51474153 and 51574175)Ph.D.Programs Foundation of Ministry of Education of the People’s Republic of China(No.20111402110004)Natural Science Foundation of Shanxi Province(Nos.2009011028-3 and 2012011022-1)
文摘The spheroidizing mechanism of W-phase in the Mg–Zn–Y–Mn–（B） alloys during solid-solution treatment was investigated by using kinetic methodologies. The microstructure and mechanical properties of heat-treated Mg_（94）Zn_（2.5）-Y_（2.5）Mn_1 alloy containing 0.003 wt% B were compared with heat-treated Mg_（94）Zn_（2.5）-Y_（2.5）Mn_1 alloy. The heat-treated Mg_（94）Zn_（2.5）-Y_（2.5）Mn_1 alloy with 0.003 wt% B contained fine and uniform W-phase particles, which exhibited optimal mechanical performance. The ultimate tensile strength, yield strength and elongation were 287.7, 125.5 MPa and 21.1%,respectively.
基金supported by the 45th China Postdoctoral Science Foundation (Grant No.20090451101)the Xiangtan University Postdoctoral Science Foundation
文摘The characteristic crystal model is applied to the study of phase stability and thermodynamics in substitutional bcc-based Ta-W alloys.The basic principle and method of alloy thermodynamics which is described by the characteristic crystal model is introduced in detail.The Gibbs energy of various phases including both disordered and ordered phases of the Ta-W system are evaluated.The phase diagram of Ta-W alloys is assessed and predicted.The results are in good agreement with experiments and better than that of first principle.
基金the National Natural Science Foundation of China(Grant Nos.51474156 and U1660201)the National High Technology Research and Development Program(‘‘863" Program)of China(Grant No.2015AA042504)for financial support
文摘Powder metallurgic Ti2 AlNb alloys with W addition are sintered at 900, 1000, 1070 °C,and 1150 °C(i.e., in the O + B2, a_2+ B2 + O, a_2+ B2, and single B2 phase regions, respectively)for 12 h, followed by water quenching and furnace cooling. Comparisons of phase and microstructure between quenched and furnace-cooled W-modified alloys are carried out to illustrate the phase transformation and microstructure evolution during the cooling process. Furthermore, a comparison is also made between W-modified and W-free alloys, to reveal the function of the W alloying.W addition accelerates the solutions of a_2 and O phases during the high-temperature holding, and a Widmannsta¨tten B2 + O structure, which contributes to the properties, is induced by furnace cooling from all the phase regions. The Widmannsta¨tten structure includes a B2 matrix, primary O, and secondary O precipitates. However, W alloying refines the Widmannsta¨tten structure only when the alloys are solution-treated and then cooled from the single B2 phase. Although the hardness of the W-modified alloys is lower than that of the W-free alloys sintered in the same phase region, an enhancement of hardness, 489 ± 18 HV, is obtained in the alloy solution-treated in the single B2 phase region for only 0.5 h.
基金This work was financially supported by the National Natural Science Foundation of China (No. 50174007).
文摘The kinetic characteristics of W grain growth operated by diffusion controlled Oswald ripening （DOR） during liquid phase sintering were studied. A liquid phase sintering of W-15wt%Cu was carried out by pushing compacts into a furnace at the moment when the temperature increased to 1340℃ for different sintering times. The results show that liquid phase sintering produces the compacts with considerably low relative density and inversely, rather high homogeneity. On the basis of the data extracted from the SEM images, the kinetic equation of W grain growth, G^n = G0^n ＋ kt, is determined in which the grain growth exponent n is 3 and the grain growth rate constant k is 0.15 μm^3/s. The cumulative normalized grain size distributions produced by different sintering times show self-similar. The cumulative distribution function is extracted from the curves by non-linear fitting. In addition, the sintering kinetic characteristics of W-15wt%Cu compacts were also investigated.
文摘A new tungsten heavy alloy, W-Ni-Fe-TiB_2 was studied. This ally has higher hardness than tradition-al tungsten heavy alloy. Sintering time was 30 min for producing the alloy. In the new tungsten heavy alloy, four phases were found to be W, γ (Ni, Fe), TiB_2 and complex haride compound. TiB_2 and complexboride compound were precipitated in the matrix. So TiB_2 could strengthen the tungsten heavy alloy.
文摘The precipitation behaviour of Fe-Cr-Mo and Fe-Cr-W alloys during aging has been ex- perimentally studied.It was found that in the early stage of aging,a metastable R phase pre- cipitated in both alloys,it was transformed into stable μ-phase,Laves-phase,X-phase or σ-phase in the later stages.The crystallographic structure of metastable R-phase is rhombohedral with lattice parameters of a=0.9075 nm and α=74.45°.The chemical compo- sition of R-phase is Fe-(27.5—34.9)Mo-(0—25.5)Cr and Fe-(28.9—33.0)W-(9.36— 21.0)Cr in at.-% in Fe-Cr-Mo and Fe-Cr-W system,respectively.
文摘Phase stability of four different chemical component Fe-Cr-Mn(W, V) alloys are investigated by experimental method and thermodynamic model in this paper. It is indicated that the main phase of four alloys after aged under 623, 673, 773K for 200h are austenitic phase. The results of Thermo-Calc, which are based on Gibbs energy, show that the phases of four alloys under ihe same temperature as experimental method are single austenitic phase. The results of experimental method and Thermo-Calc agree well.
文摘Pure W and W-Cu-W trilayer coatings were deposited on an Fe substrate by d.c. magnetron sputtering. The α-β phase evolution, intragranular stress evolution in sputter-deposited W layer were investigated by x-ray diffraction. They are directly related to the film microstructure, density and adhesion. Therefore, control of the film stress and phase component transition is essential for its applications. The phase component transition from β-W to α-W and intragranular stress evolution from tensile to compressive strongly depend on the deposition parameters and can be induced by lowering Ar pressure and rising target power. The compressively stressed films with α-W phase have a dense microstructure and high adhesion to Fe substrate.
文摘本文采用最新文献报道的Ni-Cr、Ni-W和Cr-W二元热力学参数,结合Ni-Cr-W三元体系实验数据,使用相图计算(calculation of phase diagram,CALPHAD)方法进行热力学评估和优化计算,获得了一套自洽的热力学参数,其中σ相的热力学模型为亚点阵模型:(Cr,Ni,W)_(0.533)(Cr,Ni,W)_(0.333)(Cr,Ni,W)_(0.134)。计算的Ni-Cr-W体系等温截面图(1273、1473、1673和1813 K)和液相面投影图与实验数据匹配较好,说明本工作的热力学数据库能够很好地再现实验结果,对此体系相关的高元合金设计具有参考意义。
