BACKGROUND Pancreatic fibrosis,which decreases risk of postoperative pancreatic fistula(POPF),can be estimated using extracellular volume fraction(ECVf).AIM To investigate the correlation between ECVf and pancreatic h...BACKGROUND Pancreatic fibrosis,which decreases risk of postoperative pancreatic fistula(POPF),can be estimated using extracellular volume fraction(ECVf).AIM To investigate the correlation between ECVf and pancreatic histology,as well as the usefulness of ECVf in predicting POPF.METHODS In 71 patients who underwent pancreatic resection,we caluculated pancreatic ECVf by comparing absolute enhancements of the pancreas and aorta between pre-contrast and equilibrium phases.Areas of fibrosis,fat,acini,and islets were calculated based on resection specimens.RESULTS ECVf correlated with fibrosis(r=0.724;P<0.001)and negatively correlated with acini(r=-0.510;P<0.001).Among 48 patients who underwent pancreatoduoden ectomy,21 developed POPF.Main pancreatic duct diameter≤2 mm and ECVf<36%were selected as risk factors by multivariate analysis[respective odds ratios(OR)and P values,4.26 and P=0.048;OR=11.07 and P=0.036].Using these factors as a risk score(0-2 points),POPF occurred in 0%,50%,and 70%of patients with 0,1,and 2 points,respectively.CONCLUSION ECVf is useful in predicting acinar loss and pancreatic fibrosis,and ECVf<36%may be a risk factor for POPF.展开更多
Quantitative measurement of Soot Volume Fraction (SVF) is an essential prerequisite for controlling soot particle emissions from aero-engine combustors. As an in-situ and non-intrusive optical diagnostic technique, La...Quantitative measurement of Soot Volume Fraction (SVF) is an essential prerequisite for controlling soot particle emissions from aero-engine combustors. As an in-situ and non-intrusive optical diagnostic technique, Laser-Induced Incandescence (LII) has been increasingly applied for soot concentration quantification in various combustion environments such as laminar flame, vehicle exhaust, internal combustion chamber as well as aero-engine combustor. In this work, we experimentally measured the spatial and temporal distribution of SVF using two-color LII technique at the outlet of a single-sector dual-swirl aero-engine model combustor. The effect of inlet pressure and air preheat temperature on the SVF distribution was separately investigated within a pressure range of 241–425 kPa and a temperature range of 292–500 K. The results show that soot production increases with the inlet pressure but generally decreases with the air preheat temperature. Qualitative analysis was provided to explain the above results of parametric studies. The LII experiments were also conducted under 3 designed conditions to evaluate soot emission under practical operations. Particularly, weak soot emission was detected at the outlet under the idle condition. Our experimental results provide a valuable benchmark for evaluating soot emission in the exhaust plume of this aero-engine combustor during practical operations.展开更多
To improve the understanding of coupling effect between dynamic recrystallization(DRX)behaviors and flow behaviors of as-cast AlCu4 SiMg, a finite element(FE) simulation equipped with the models of DRX evolution was i...To improve the understanding of coupling effect between dynamic recrystallization(DRX)behaviors and flow behaviors of as-cast AlCu4 SiMg, a finite element(FE) simulation equipped with the models of DRX evolution was implemented. A series of isothermal compression tests were performed primarily on a Gleeble-3500 thermo-mechanical simulator in a temperature range of 648-748 K and a strain rate range of 0.01-10 s-1.According to the measured true stress-strain data,the strain hardening rate curves(dσ/dε versus σ) were plotted to identify the critical strains for DRX initiation(εc). By further derivation of the related material constants, the DRX volume fraction equation and the strain for 50% DRX(ε0.5) equation were solved. Accordingly, the aforementioned DRX equations were implanted into the FE model to conduct a series of simulations for the isothermal compression tests. The results show that during the evolution of DRX volume fraction at a fixed strain rate, the strain required for the same amount of DRX volume fraction increases with decreasing temperature. In contrast, at a fixed temperature, it increases with increasing strain rate. Ultimately, the DRX kinetics model of AlCu4 SiMg alloy and the consequence of the FE analysis were validated by microstructure observations.展开更多
The fabrication of high volume fraction （HVF） M7C3 （M=Cr, Fe） reinforced Fe-based composite coating on ASTM A36 steel plate using plasma transferred arc （PTA） welding was studied. The results showed that the vol...The fabrication of high volume fraction （HVF） M7C3 （M=Cr, Fe） reinforced Fe-based composite coating on ASTM A36 steel plate using plasma transferred arc （PTA） welding was studied. The results showed that the volume fraction of carbide M7C3 was more than sixty percent, and the relative wear resistance of the coating tested on a block-on-ring dry sliding tester at constant load （100 N） and variable loads （from 100 to 300 N） respectively was about 9 and 14 times higher than that of non-reinforced a-Fe coating. In addition, under constant load condition the friction coefficients （FCs） of two coatings increased first and then decreased with increasing sliding distance. However, under variable loads condition the FCs of non-reinforced a-Fe based coating increased gradually, while that of HVF MTC3 reinforced coating decreased as the load exceeded 220 N. The worn surface of non-reinforced a-Fe based coating was easily deformed and grooved, while that of the HVF M7C3 reinforced coating was difficult to be deformed and grooved.展开更多
A hot-rolled medium Mn(0.2C5Mn)steel is annealed at 650℃ to produce an ultrafine-grained duplex microstructure with different austenite volume fractions by austenite reverted transformation(ART)annealing,and the orie...A hot-rolled medium Mn(0.2C5Mn)steel is annealed at 650℃ to produce an ultrafine-grained duplex microstructure with different austenite volume fractions by austenite reverted transformation(ART)annealing,and the orientation relationship strictly obeys K-S orientation relationship before deformation.Tensile tests are carried out in a temperature range from-196 to 400℃ to examine the effects of the austenite volume fraction and the deformation temperature on the tensile properties and the austenite stability.Microstructural observations reveal that the metastable austenite gradually transformed into a-martensite,which is controlled by the deformation strain,the temperature and the austenite volume fraction.Both strain hardening behavior and ductility of the studied steel are dependent on austenite volume fraction and deformation temperature significantly.The stress-strain curves of ART-annealed 0.2C5Mn steel assume an S shape and a very large work hardening rate of about 10 GPa is obtained at liquid nitrogen deformation temperature.Based on the experimental data,a quantitative relation is proposed to describe the ductility dependence on both the austenite volume fraction and its mechanical stability.展开更多
A conventional X-ray difFractometer has been used to determine the -y/y＇ lattice misfit and γ＇ volume fraction for a Ru-containing nickel-based single crystal superalloy at room temperature. The rocking curve was u...A conventional X-ray difFractometer has been used to determine the -y/y＇ lattice misfit and γ＇ volume fraction for a Ru-containing nickel-based single crystal superalloy at room temperature. The rocking curve was used to characterize the distribution of subgrains. The diffraction peaks obtained by w-20 scan were used to determine the γ/γ＇ lattice misfit and γ＇ volume fraction. A three peaks fitting model was proposed. The peak fitting results are in good agreement with the model. The X-ray diffraction results indicate that the nickel-based single crystal superalloy was not a perfect monocrystalline material, which is comprised of many subgrains; and each subgrain also consists of large numbers of mosaic structures. In addition, two anomalous reflection phenomena were found during the experiment and discussed with respect to their occurrence and impact on the measurement. The experimental results show that the γ/γ＇ lattice misfit and ~/r volume fraction will be various at the different regions of its dendritic microstructure. The average γ/γ＇ lattice misfit and γ＇ volume fraction of the experimental alloy are approximately-0.2% and 70%, respectively. Furthermore, the γ＇ volume fraction calculated by atom microprobe （AP） data is also basically consistent with the experimental results.展开更多
In this paper, the influence of an exponential volume fraction law on the vibration frequencies of thin functionally graded cylindrical shells is studied. Material properties in the shell thickness direction are grade...In this paper, the influence of an exponential volume fraction law on the vibration frequencies of thin functionally graded cylindrical shells is studied. Material properties in the shell thickness direction are graded in accordance with the exponential law. Expressions for the strain-displacement and curvature-displacement relationships are taken from Love＇s thin shell theory. The Rayleigh-Ritz approach is used to derive the shell eigenfrequency equation. Axial modal dependence is assumed in the characteristic beam functions. Natural frequencies of the shells are observed to be dependent on the constituent volume fractions. The results are compared with those available in the literature for the validity of the present methodology.展开更多
A combined computational and experimental investigation to examine temperature and soot volume fraction in coflow ethylene-air diffusion flames was presented.A numerical simulation was conducted by using a relatively ...A combined computational and experimental investigation to examine temperature and soot volume fraction in coflow ethylene-air diffusion flames was presented.A numerical simulation was conducted by using a relatively detailed gas-phase chemistry and complex thermal and transport properties coupled with a semi-empirical two-equation soot model.Thermal radiation was calculated using the discrete ordinates method.An image processing technique and a decoupled reconstruction method were used to simultaneously measure the distributions of temperature and soot volume fraction.The results show that the maximum error for temperature does not exceed 10% between the prediction and the measurement.And the maximum error is 6.9% for soot volume fraction between prediction and measurement.Additional simulations were performed to explore the effects of global equivalence ratio on diffusion flames and the soot formation.The results display that the soot formation increases with decreasing the coflow air velocity.And the soot formation in each case appears in the annular region,where the temperature ranges from about 1 000 K to 2 000 K and the profile becomes taller and wider when the coflow air is decreased.展开更多
This paper presents the use of a high performance dual-plane electrical resistance tomography (ERT) system and a local dual-sensor conductance probe to measure the vertical upward oil-in-water pipe flows in which the ...This paper presents the use of a high performance dual-plane electrical resistance tomography (ERT) system and a local dual-sensor conductance probe to measure the vertical upward oil-in-water pipe flows in which the mean oil volume fraction is up to 23.1%. A sensitivity coefficient back-projection (SBP) algorithm was adopted to reconstruct the flow distributions and a cross correlation method was applied to obtain the oil velocity distributions. The oil volume fraction and velocity distributions obtained from both measurement techniques were compared and good agreement was found, which indicates that the ERT tech- nique can be used to measure the low fraction oil-water flows. Finally, the factors affecting measurement precision were discussed.展开更多
The effects of fiber volume fraction on damping properties of carbon fiber three-dimensional and five-directional( 3D-5Dir)braided carbon fiber / epoxyres in composite cantilever beams were studied by experimental mod...The effects of fiber volume fraction on damping properties of carbon fiber three-dimensional and five-directional( 3D-5Dir)braided carbon fiber / epoxyres in composite cantilever beams were studied by experimental modal analysis method. Meanwhile,carbon fiber plain woven laminated / epoxy resin composites with different fiber volume fraction were concerned for comparison. The experimental result of braided specimens shows that the first three orders of natural frequency increase and the first three orders of the damping ratios of specimens decrease, when the fiber volume fraction increases. Furthermore,larger fiber volume fraction will be valuable for the better anti-exiting property of braided composites,and get an opposite effect on dissipation of vibration energy. The fiber volume fraction is an important factor for vibration performance design of braided composites. The comparison between the braided specimens and laminated specimens reveals that 3D braided composites have a wider range of damping properties than laminated composites with the same fiber volume fractions.展开更多
The longitudinal tensile properties of SiCf/Ti-6Al-4V composites with different fiber volume fractions were simulated by the Monte Carlo 2-D finite element model. The random distribution of fiber strength was expresse...The longitudinal tensile properties of SiCf/Ti-6Al-4V composites with different fiber volume fractions were simulated by the Monte Carlo 2-D finite element model. The random distribution of fiber strength was expressed by the two-parameter Weibull function. Meanwhile, contact elements and birth-death elements were used to describe the interfacial sliding process after debonding and fiber breakage（or matrix cracking） respectively, which was realized by subroutine complied in ANSYS-APDL（ANSYS Parametric Design Language）. The experimental results show that the yield stress and ultimate tensile strength of SiCf/Ti-6Al-4V composites increase with increasing fiber volume fraction, while the corresponding strain of them is just on the contrary. In addition, almost the same failure mode is obtained in SiCf/Ti-6Al-4V composites with various fiber volume fractions when the interfacial shear strength is fixed. Finally, the tensile strength predicted by finite element analysis is compared with that predicted by Global load-sharing model, Local load-sharing model and conventional rule of mixtures, thus drawing the conclusion that Local load-sharing model is very perfect for the prediction of the ultimate tensile strength.展开更多
The accurate measurement of volume fraction of oil-water two-phase flow on line is important in the oil field.This paper presents a new coaxial conductivity sensor for measuring the volume fraction of oil-water two-ph...The accurate measurement of volume fraction of oil-water two-phase flow on line is important in the oil field.This paper presents a new coaxial conductivity sensor for measuring the volume fraction of oil-water two-phase flow.This structure may get the more uniform sensitivity field and the vertical installation may get the more axial symmetry of the flow field,which improve the measurement accuracy.In order to minimize the influence of the edge effect,guard electrodes were designed.An anti-edge effect degree Ae was defined to optimize the length of the guard electrode.Different models of effective conductivity of two materials were used in calculating the oil volume fraction of oil-water two-phase flow.The experimental results indicate that Maxwell model is the best model under the condition of oil volume fraction less than 50%and the mean value of the calculation results using Maxwell model and Bruggeman model possesses higher accuracy in the range of oil volume fraction(50%-70%).The experimental results show that the sensor obtains similar measurement performance in both vertical upward and downward flow conditions.The accuracy of the sensor system is 2%when the oil volume fraction less than 50%,and the accuracy is about 5%when the oil volume fraction between 50%and 70%.展开更多
Refractive index matching(RIM)is widely used to investigate particle-liquid mixture flows.However,determining the volume fractionφin RIM is generally empirical and lacks theoretical or experimental basis.To reasonabl...Refractive index matching(RIM)is widely used to investigate particle-liquid mixture flows.However,determining the volume fractionφin RIM is generally empirical and lacks theoretical or experimental basis.To reasonably reconstruct the internalφ,this study performs systematic calibration experiments to study the relationship betweenφand the imaging indicators.The results show that the model based on area fraction c2D will induce a large error for lowφowing to the instability of the particle’s apparent size.The traditionally adopted proportional functionφ=ac2D is only valid forφnear the calibration point.A predictive model is proposed based on the size of the Voronoi cell,dpoly,which proves to be more accurate and stable in RIM experiments.The dpoly-based model is applied to dense granular flows down an inclined plane to study the internal profiles ofφand the bottom normal stress.展开更多
A phase transformation model was presented for predicting the phase fraction transformed and the carbon concentration in austenite for austenite to ferrite transformation during laminar cooling on run-out table in hot...A phase transformation model was presented for predicting the phase fraction transformed and the carbon concentration in austenite for austenite to ferrite transformation during laminar cooling on run-out table in hot rolling strip mill. In this model, the parameter k in Avrami equation was developed for carbon steels. The wide range of chemical composition, the primary austenite grain size, and the retained strain were taken into account. It can be used to predict the ferrite volume fraction and the carbon concentration in austenite of hot-rolled steel strip during laminar cooling on run-out table. The coiling temperature controlling model was also presented to calculate the temperature of steel strip. The transformation kinetics of austenite to ferrite and the evolution of carbon concentration in austenite at different temperatures during cooling were investigated in the hot rolled Q235B strip for thickness of 9.35, 6.4, and 3.2mm. The ferrite volume fraction along the length of the strip was also calculated. The calculated ferrite volume fraction was compared with the log data from hot strip mill and the calculated results were in agreement with the experimental ones. The present study is a part of the prediction of the mechanical properties of hot-rolled steel strip, and it has already been used on-line and off-line in the hot strip mill.展开更多
Submarine seep plumes are a natural phenomenon in which different types of gases migrate through deep or shallow subsurface sediments and leak into seawater in pressure gradient.When detected using acoustic data,the l...Submarine seep plumes are a natural phenomenon in which different types of gases migrate through deep or shallow subsurface sediments and leak into seawater in pressure gradient.When detected using acoustic data,the leaked gases frequently exhibit a flame-like structure.We numerically modelled the relationship between the seismic response characteristic and bubble volume fraction to establish the bubble volume fraction in the submarine seep plume.Results show that our models are able to invert and predict the bubble volume fraction from field seismic oceanography data,by which synthetic seismic sections in different dominant frequencies could be numerically simulated,seismic attribute sections(e.g.,instantaneous amplitude,instantaneous frequency,and instantaneous phase)extracted,and the correlation between the seismic attributes and bubble volume fraction be quantitatively determined with functional equations.The instantaneous amplitude is positively correlated with bubble volume fraction,while the instantaneous frequency and bubble volume fraction are negatively correlated.In addition,information entropy is introduced as a proxy to quantify the relationship between the instantaneous phase and bubble volume fraction.As the bubble volume fraction increases,the information entropy of the instantaneous phase increases rapidly at the beginning,followed by a slight upward trend,and finally stabilizes.Therefore,under optimal noise conditions,the bubble volume fraction of submarine seep plumes can be inverted and predicted based on seismic response characteristics in terms of seismic attributes.展开更多
On the basis of phase transformation kinetics, the transformation of γ→α,P,B have been investigated through considering the effect of deformation. The calculation methods of volume fraction have also been given. Co...On the basis of phase transformation kinetics, the transformation of γ→α,P,B have been investigated through considering the effect of deformation. The calculation methods of volume fraction have also been given. Comparing with common method, the simulated results are in more agreement with experiment results.展开更多
Based on previous work, abrasive wear resistance of Al 2O 3/steel composites with different Al 2O 3 particle volume fraction (VOF) at 900 ℃ was investigated. The experimental results showed that a suitable particle V...Based on previous work, abrasive wear resistance of Al 2O 3/steel composites with different Al 2O 3 particle volume fraction (VOF) at 900 ℃ was investigated. The experimental results showed that a suitable particle VOF is important to protect the metal matrix from wear at elevated temperature. Both too high and too low particle VOF lead to a poor abrasive wear because a bulk matrix is easily worn off by grits when it exceeds the suitable VOF and also because when VOF is low, the Al 2O 3 particles are easily dug out by grits during wearing as well. When the particle VOF is 39%, the wear resistance of tested composites is excellent.展开更多
The purpose of this paper is to study the dynamic behavior of softground including a porous layer by considering porosity change. Inorder to take the porosity change into account, the concept of thevolume fraction, wh...The purpose of this paper is to study the dynamic behavior of softground including a porous layer by considering porosity change. Inorder to take the porosity change into account, the concept of thevolume fraction, which has been proposed in continuum mechanics, isintroduced. The constitutive equations presented by Bowen are appliedto the analysis of the porous media. According to Bowen's theory, theporosity is considered as a variable called the volume fraction andhas its own consti- Tutive equation.展开更多
Coarse-grained（CG） metals strengthened by nanotwinned（NT） regions possess high strength and good ductility. As such, they are very suitable for applications in bullet-proof targets. Here, a numerical model based o...Coarse-grained（CG） metals strengthened by nanotwinned（NT） regions possess high strength and good ductility. As such, they are very suitable for applications in bullet-proof targets. Here, a numerical model based on the conventional theory of strain gradient plasticity and the Johnson–Cook failure criterion is employed to study the influences of volume fraction of NT regions on their ballistic performance.The results show that in general a relatively small twin spacing（4–10 nm） and a moderate volume fraction（7%–20%） will lead to excellent limit velocity and that the influences of volume fraction on limit displacement change with the category of impact processes.展开更多
Welded mild steel is used in different applications in engineering. To strengthen the joint, the weld can be reinforced by adding titanium alloy powder to the joint. This results in the formation of incomplete martens...Welded mild steel is used in different applications in engineering. To strengthen the joint, the weld can be reinforced by adding titanium alloy powder to the joint. This results in the formation of incomplete martensite in a welded joint. The incomplete martensite affects mechanical properties. Therefore, this study aims to predict the volume fraction of martensite in reinforced butt welded joints to understand complex phenomena during microstructure formation. To do so, a combination of the finite element method to predict temperature history, and the Koistinen and Marburger equation, were used to predict the volume fraction of martensite. The martensite start temperature was calculated using chemical elements obtained from the dilution-based mixture rule. The curve shape of martensite evolution was observed to be relatively linear due to the small quantity of martensite volume fraction. The simulated result correlated with experimental work documented in the literature. The model can be used in other powder addition techniques where the martensite can be observed in the final microstructure.展开更多
文摘BACKGROUND Pancreatic fibrosis,which decreases risk of postoperative pancreatic fistula(POPF),can be estimated using extracellular volume fraction(ECVf).AIM To investigate the correlation between ECVf and pancreatic histology,as well as the usefulness of ECVf in predicting POPF.METHODS In 71 patients who underwent pancreatic resection,we caluculated pancreatic ECVf by comparing absolute enhancements of the pancreas and aorta between pre-contrast and equilibrium phases.Areas of fibrosis,fat,acini,and islets were calculated based on resection specimens.RESULTS ECVf correlated with fibrosis(r=0.724;P<0.001)and negatively correlated with acini(r=-0.510;P<0.001).Among 48 patients who underwent pancreatoduoden ectomy,21 developed POPF.Main pancreatic duct diameter≤2 mm and ECVf<36%were selected as risk factors by multivariate analysis[respective odds ratios(OR)and P values,4.26 and P=0.048;OR=11.07 and P=0.036].Using these factors as a risk score(0-2 points),POPF occurred in 0%,50%,and 70%of patients with 0,1,and 2 points,respectively.CONCLUSION ECVf is useful in predicting acinar loss and pancreatic fibrosis,and ECVf<36%may be a risk factor for POPF.
基金supported by the National Key Research and Development Program of China(No.2020YFA0405700).
文摘Quantitative measurement of Soot Volume Fraction (SVF) is an essential prerequisite for controlling soot particle emissions from aero-engine combustors. As an in-situ and non-intrusive optical diagnostic technique, Laser-Induced Incandescence (LII) has been increasingly applied for soot concentration quantification in various combustion environments such as laminar flame, vehicle exhaust, internal combustion chamber as well as aero-engine combustor. In this work, we experimentally measured the spatial and temporal distribution of SVF using two-color LII technique at the outlet of a single-sector dual-swirl aero-engine model combustor. The effect of inlet pressure and air preheat temperature on the SVF distribution was separately investigated within a pressure range of 241–425 kPa and a temperature range of 292–500 K. The results show that soot production increases with the inlet pressure but generally decreases with the air preheat temperature. Qualitative analysis was provided to explain the above results of parametric studies. The LII experiments were also conducted under 3 designed conditions to evaluate soot emission under practical operations. Particularly, weak soot emission was detected at the outlet under the idle condition. Our experimental results provide a valuable benchmark for evaluating soot emission in the exhaust plume of this aero-engine combustor during practical operations.
基金Project(cstc2016jcyjA0335)supported by Chongqing Foundation and Frontier Research,ChinaProject(P2017-020)supported by Open Fund Project of State Key Laboratory of Materials Processing and Die&Mould Technology,China
文摘To improve the understanding of coupling effect between dynamic recrystallization(DRX)behaviors and flow behaviors of as-cast AlCu4 SiMg, a finite element(FE) simulation equipped with the models of DRX evolution was implemented. A series of isothermal compression tests were performed primarily on a Gleeble-3500 thermo-mechanical simulator in a temperature range of 648-748 K and a strain rate range of 0.01-10 s-1.According to the measured true stress-strain data,the strain hardening rate curves(dσ/dε versus σ) were plotted to identify the critical strains for DRX initiation(εc). By further derivation of the related material constants, the DRX volume fraction equation and the strain for 50% DRX(ε0.5) equation were solved. Accordingly, the aforementioned DRX equations were implanted into the FE model to conduct a series of simulations for the isothermal compression tests. The results show that during the evolution of DRX volume fraction at a fixed strain rate, the strain required for the same amount of DRX volume fraction increases with decreasing temperature. In contrast, at a fixed temperature, it increases with increasing strain rate. Ultimately, the DRX kinetics model of AlCu4 SiMg alloy and the consequence of the FE analysis were validated by microstructure observations.
基金Funded by the National Natural Science Fundation of China(No.51171116)the Ministry of Science and Technology of China(No.2009DFB50350)+1 种基金the Research Foundation of Education Bureau of Hubei Province,China(No.Q20122304)the Foundation of Hubei University of Automotive Technology,China(No.BK201205)
文摘The fabrication of high volume fraction （HVF） M7C3 （M=Cr, Fe） reinforced Fe-based composite coating on ASTM A36 steel plate using plasma transferred arc （PTA） welding was studied. The results showed that the volume fraction of carbide M7C3 was more than sixty percent, and the relative wear resistance of the coating tested on a block-on-ring dry sliding tester at constant load （100 N） and variable loads （from 100 to 300 N） respectively was about 9 and 14 times higher than that of non-reinforced a-Fe coating. In addition, under constant load condition the friction coefficients （FCs） of two coatings increased first and then decreased with increasing sliding distance. However, under variable loads condition the FCs of non-reinforced a-Fe based coating increased gradually, while that of HVF MTC3 reinforced coating decreased as the load exceeded 220 N. The worn surface of non-reinforced a-Fe based coating was easily deformed and grooved, while that of the HVF M7C3 reinforced coating was difficult to be deformed and grooved.
基金This research was supported by both National Natural Science Foundation of China(NSFC,Nos.51871062,51371057 and 11672195)MNSF of Beijing(No.2182088)Chong-xiang Huang acknowledged Sichuan Youth Science and Technology Foundation(No.2016JQ0047).
文摘A hot-rolled medium Mn(0.2C5Mn)steel is annealed at 650℃ to produce an ultrafine-grained duplex microstructure with different austenite volume fractions by austenite reverted transformation(ART)annealing,and the orientation relationship strictly obeys K-S orientation relationship before deformation.Tensile tests are carried out in a temperature range from-196 to 400℃ to examine the effects of the austenite volume fraction and the deformation temperature on the tensile properties and the austenite stability.Microstructural observations reveal that the metastable austenite gradually transformed into a-martensite,which is controlled by the deformation strain,the temperature and the austenite volume fraction.Both strain hardening behavior and ductility of the studied steel are dependent on austenite volume fraction and deformation temperature significantly.The stress-strain curves of ART-annealed 0.2C5Mn steel assume an S shape and a very large work hardening rate of about 10 GPa is obtained at liquid nitrogen deformation temperature.Based on the experimental data,a quantitative relation is proposed to describe the ductility dependence on both the austenite volume fraction and its mechanical stability.
基金supported by the National Basic Research Program (973 Program) of China under grant No. 2010CB631200the National Natural Science Foundation of China (NSFC) under grant No.50931004
文摘A conventional X-ray difFractometer has been used to determine the -y/y＇ lattice misfit and γ＇ volume fraction for a Ru-containing nickel-based single crystal superalloy at room temperature. The rocking curve was used to characterize the distribution of subgrains. The diffraction peaks obtained by w-20 scan were used to determine the γ/γ＇ lattice misfit and γ＇ volume fraction. A three peaks fitting model was proposed. The peak fitting results are in good agreement with the model. The X-ray diffraction results indicate that the nickel-based single crystal superalloy was not a perfect monocrystalline material, which is comprised of many subgrains; and each subgrain also consists of large numbers of mosaic structures. In addition, two anomalous reflection phenomena were found during the experiment and discussed with respect to their occurrence and impact on the measurement. The experimental results show that the γ/γ＇ lattice misfit and ~/r volume fraction will be various at the different regions of its dendritic microstructure. The average γ/γ＇ lattice misfit and γ＇ volume fraction of the experimental alloy are approximately-0.2% and 70%, respectively. Furthermore, the γ＇ volume fraction calculated by atom microprobe （AP） data is also basically consistent with the experimental results.
文摘In this paper, the influence of an exponential volume fraction law on the vibration frequencies of thin functionally graded cylindrical shells is studied. Material properties in the shell thickness direction are graded in accordance with the exponential law. Expressions for the strain-displacement and curvature-displacement relationships are taken from Love＇s thin shell theory. The Rayleigh-Ritz approach is used to derive the shell eigenfrequency equation. Axial modal dependence is assumed in the characteristic beam functions. Natural frequencies of the shells are observed to be dependent on the constituent volume fractions. The results are compared with those available in the literature for the validity of the present methodology.
基金Projects(50806024,50806023 and 50806026) supported by the National Natural Science Foundation of China
文摘A combined computational and experimental investigation to examine temperature and soot volume fraction in coflow ethylene-air diffusion flames was presented.A numerical simulation was conducted by using a relatively detailed gas-phase chemistry and complex thermal and transport properties coupled with a semi-empirical two-equation soot model.Thermal radiation was calculated using the discrete ordinates method.An image processing technique and a decoupled reconstruction method were used to simultaneously measure the distributions of temperature and soot volume fraction.The results show that the maximum error for temperature does not exceed 10% between the prediction and the measurement.And the maximum error is 6.9% for soot volume fraction between prediction and measurement.Additional simulations were performed to explore the effects of global equivalence ratio on diffusion flames and the soot formation.The results display that the soot formation increases with decreasing the coflow air velocity.And the soot formation in each case appears in the annular region,where the temperature ranges from about 1 000 K to 2 000 K and the profile becomes taller and wider when the coflow air is decreased.
基金Project (No. 15933) supported by the Royal Society-Chinese Acad-emy of Sciences Joint Project
文摘This paper presents the use of a high performance dual-plane electrical resistance tomography (ERT) system and a local dual-sensor conductance probe to measure the vertical upward oil-in-water pipe flows in which the mean oil volume fraction is up to 23.1%. A sensitivity coefficient back-projection (SBP) algorithm was adopted to reconstruct the flow distributions and a cross correlation method was applied to obtain the oil velocity distributions. The oil volume fraction and velocity distributions obtained from both measurement techniques were compared and good agreement was found, which indicates that the ERT tech- nique can be used to measure the low fraction oil-water flows. Finally, the factors affecting measurement precision were discussed.
基金Tianjin Municipal Science and Technologies Commission,China(Nos.10SYSYJC27800,1ZCKFSF00500)
文摘The effects of fiber volume fraction on damping properties of carbon fiber three-dimensional and five-directional( 3D-5Dir)braided carbon fiber / epoxyres in composite cantilever beams were studied by experimental modal analysis method. Meanwhile,carbon fiber plain woven laminated / epoxy resin composites with different fiber volume fraction were concerned for comparison. The experimental result of braided specimens shows that the first three orders of natural frequency increase and the first three orders of the damping ratios of specimens decrease, when the fiber volume fraction increases. Furthermore,larger fiber volume fraction will be valuable for the better anti-exiting property of braided composites,and get an opposite effect on dissipation of vibration energy. The fiber volume fraction is an important factor for vibration performance design of braided composites. The comparison between the braided specimens and laminated specimens reveals that 3D braided composites have a wider range of damping properties than laminated composites with the same fiber volume fractions.
基金Funded by the National Natural Science Foundation of China(51271147)
文摘The longitudinal tensile properties of SiCf/Ti-6Al-4V composites with different fiber volume fractions were simulated by the Monte Carlo 2-D finite element model. The random distribution of fiber strength was expressed by the two-parameter Weibull function. Meanwhile, contact elements and birth-death elements were used to describe the interfacial sliding process after debonding and fiber breakage（or matrix cracking） respectively, which was realized by subroutine complied in ANSYS-APDL（ANSYS Parametric Design Language）. The experimental results show that the yield stress and ultimate tensile strength of SiCf/Ti-6Al-4V composites increase with increasing fiber volume fraction, while the corresponding strain of them is just on the contrary. In addition, almost the same failure mode is obtained in SiCf/Ti-6Al-4V composites with various fiber volume fractions when the interfacial shear strength is fixed. Finally, the tensile strength predicted by finite element analysis is compared with that predicted by Global load-sharing model, Local load-sharing model and conventional rule of mixtures, thus drawing the conclusion that Local load-sharing model is very perfect for the prediction of the ultimate tensile strength.
基金supported by National Natural Science Foundation of China(Grant No.61072101)Program for New Century Excellent Talents in University(Grant No.NCET-10-0621)the Independent Innovation Foundation of Tianjin University
文摘The accurate measurement of volume fraction of oil-water two-phase flow on line is important in the oil field.This paper presents a new coaxial conductivity sensor for measuring the volume fraction of oil-water two-phase flow.This structure may get the more uniform sensitivity field and the vertical installation may get the more axial symmetry of the flow field,which improve the measurement accuracy.In order to minimize the influence of the edge effect,guard electrodes were designed.An anti-edge effect degree Ae was defined to optimize the length of the guard electrode.Different models of effective conductivity of two materials were used in calculating the oil volume fraction of oil-water two-phase flow.The experimental results indicate that Maxwell model is the best model under the condition of oil volume fraction less than 50%and the mean value of the calculation results using Maxwell model and Bruggeman model possesses higher accuracy in the range of oil volume fraction(50%-70%).The experimental results show that the sensor obtains similar measurement performance in both vertical upward and downward flow conditions.The accuracy of the sensor system is 2%when the oil volume fraction less than 50%,and the accuracy is about 5%when the oil volume fraction between 50%and 70%.
基金the National Natural Science Foundation of China(Grant Nos.12032005 and 12172057)。
文摘Refractive index matching(RIM)is widely used to investigate particle-liquid mixture flows.However,determining the volume fractionφin RIM is generally empirical and lacks theoretical or experimental basis.To reasonably reconstruct the internalφ,this study performs systematic calibration experiments to study the relationship betweenφand the imaging indicators.The results show that the model based on area fraction c2D will induce a large error for lowφowing to the instability of the particle’s apparent size.The traditionally adopted proportional functionφ=ac2D is only valid forφnear the calibration point.A predictive model is proposed based on the size of the Voronoi cell,dpoly,which proves to be more accurate and stable in RIM experiments.The dpoly-based model is applied to dense granular flows down an inclined plane to study the internal profiles ofφand the bottom normal stress.
文摘A phase transformation model was presented for predicting the phase fraction transformed and the carbon concentration in austenite for austenite to ferrite transformation during laminar cooling on run-out table in hot rolling strip mill. In this model, the parameter k in Avrami equation was developed for carbon steels. The wide range of chemical composition, the primary austenite grain size, and the retained strain were taken into account. It can be used to predict the ferrite volume fraction and the carbon concentration in austenite of hot-rolled steel strip during laminar cooling on run-out table. The coiling temperature controlling model was also presented to calculate the temperature of steel strip. The transformation kinetics of austenite to ferrite and the evolution of carbon concentration in austenite at different temperatures during cooling were investigated in the hot rolled Q235B strip for thickness of 9.35, 6.4, and 3.2mm. The ferrite volume fraction along the length of the strip was also calculated. The calculated ferrite volume fraction was compared with the log data from hot strip mill and the calculated results were in agreement with the experimental ones. The present study is a part of the prediction of the mechanical properties of hot-rolled steel strip, and it has already been used on-line and off-line in the hot strip mill.
基金Supported by the Natural Science Foundation of Shandong Province(No.ZR2022MD074)the Laboratory for Marine Mineral Resources+3 种基金Qingdao National Laboratory for Marine Science and Technology(No.MMRKF201810)the National Natural Science Foundation of China(No.41606077)the National Key R&D Program of China:HighPrecision Characterization Technology of Gas Hydrate Reservoir(No.2017YFC0307406-03)supported by the Shandong Province Taishan Scholar Construction Project。
文摘Submarine seep plumes are a natural phenomenon in which different types of gases migrate through deep or shallow subsurface sediments and leak into seawater in pressure gradient.When detected using acoustic data,the leaked gases frequently exhibit a flame-like structure.We numerically modelled the relationship between the seismic response characteristic and bubble volume fraction to establish the bubble volume fraction in the submarine seep plume.Results show that our models are able to invert and predict the bubble volume fraction from field seismic oceanography data,by which synthetic seismic sections in different dominant frequencies could be numerically simulated,seismic attribute sections(e.g.,instantaneous amplitude,instantaneous frequency,and instantaneous phase)extracted,and the correlation between the seismic attributes and bubble volume fraction be quantitatively determined with functional equations.The instantaneous amplitude is positively correlated with bubble volume fraction,while the instantaneous frequency and bubble volume fraction are negatively correlated.In addition,information entropy is introduced as a proxy to quantify the relationship between the instantaneous phase and bubble volume fraction.As the bubble volume fraction increases,the information entropy of the instantaneous phase increases rapidly at the beginning,followed by a slight upward trend,and finally stabilizes.Therefore,under optimal noise conditions,the bubble volume fraction of submarine seep plumes can be inverted and predicted based on seismic response characteristics in terms of seismic attributes.
基金supported by the National Natural Science Foudation of China(No.50334010)National High Technical Research and Development Programme of China(No.2001AA339030)
文摘On the basis of phase transformation kinetics, the transformation of γ→α,P,B have been investigated through considering the effect of deformation. The calculation methods of volume fraction have also been given. Comparing with common method, the simulated results are in more agreement with experiment results.
文摘Based on previous work, abrasive wear resistance of Al 2O 3/steel composites with different Al 2O 3 particle volume fraction (VOF) at 900 ℃ was investigated. The experimental results showed that a suitable particle VOF is important to protect the metal matrix from wear at elevated temperature. Both too high and too low particle VOF lead to a poor abrasive wear because a bulk matrix is easily worn off by grits when it exceeds the suitable VOF and also because when VOF is low, the Al 2O 3 particles are easily dug out by grits during wearing as well. When the particle VOF is 39%, the wear resistance of tested composites is excellent.
文摘The purpose of this paper is to study the dynamic behavior of softground including a porous layer by considering porosity change. Inorder to take the porosity change into account, the concept of thevolume fraction, which has been proposed in continuum mechanics, isintroduced. The constitutive equations presented by Bowen are appliedto the analysis of the porous media. According to Bowen's theory, theporosity is considered as a variable called the volume fraction andhas its own consti- Tutive equation.
基金supported by the National Natural Science Foundation of China(11372214)the opening project of State Key Laboratory of Explosion Science and Technology(Beijing Institute of Technology)(KFJJ17-10M)+1 种基金the support of the NSF Mechanics of Materials Program under CMMI-1162431the support from the Advanced Engineering Programme and School of Engineering,Monash University Malaysia
文摘Coarse-grained（CG） metals strengthened by nanotwinned（NT） regions possess high strength and good ductility. As such, they are very suitable for applications in bullet-proof targets. Here, a numerical model based on the conventional theory of strain gradient plasticity and the Johnson–Cook failure criterion is employed to study the influences of volume fraction of NT regions on their ballistic performance.The results show that in general a relatively small twin spacing（4–10 nm） and a moderate volume fraction（7%–20%） will lead to excellent limit velocity and that the influences of volume fraction on limit displacement change with the category of impact processes.
文摘Welded mild steel is used in different applications in engineering. To strengthen the joint, the weld can be reinforced by adding titanium alloy powder to the joint. This results in the formation of incomplete martensite in a welded joint. The incomplete martensite affects mechanical properties. Therefore, this study aims to predict the volume fraction of martensite in reinforced butt welded joints to understand complex phenomena during microstructure formation. To do so, a combination of the finite element method to predict temperature history, and the Koistinen and Marburger equation, were used to predict the volume fraction of martensite. The martensite start temperature was calculated using chemical elements obtained from the dilution-based mixture rule. The curve shape of martensite evolution was observed to be relatively linear due to the small quantity of martensite volume fraction. The simulated result correlated with experimental work documented in the literature. The model can be used in other powder addition techniques where the martensite can be observed in the final microstructure.
