A design for a Li-ion battery charger IC that can operate in a constant current-constant voltage （CC- CV） charge mode is proposed. In the CC-CV charge mode,the charger IC provides a constant charging current at the ...A design for a Li-ion battery charger IC that can operate in a constant current-constant voltage （CC- CV） charge mode is proposed. In the CC-CV charge mode,the charger IC provides a constant charging current at the beginning, and then the charging current begins to decrease before the battery voltage reaches its final value. After the battery voltage reaches its final value and remains constant,the charging current is further reduced. This approach prevents charging the battery with full current near its saturated voltage,which can cause heating. The novel design of the core of the charger IC realizes the proposed CC-CV charge mode. The chip was implemented in a CSMC 0.6μm CMOS mixed signal process. The experimental results verify the realization of the proposed CC- CV charge mode. The voltage of the battery after charging is 4. 1833V.展开更多
A feedback control system is needed to restrain plasma vertical displacement in EAST （Experimental Advanced Superconducting Toknmak）. A fast control power supply excites active feedback coils, which produces a magne...A feedback control system is needed to restrain plasma vertical displacement in EAST （Experimental Advanced Superconducting Toknmak）. A fast control power supply excites active feedback coils, which produces a magnetic field to control the plasma＇s displacement. With the development of EAST, new demands on the new fast control power supply have led to an enhanced ability of fast response and output current, as well as a new control mode. The structure of cascaded and paralleled H-bridges can meet the demand of extended capacity, and digital control can reMize current and voltage mixed control mode. The validity of the proposed scheme is confirmed by experiments.展开更多
This study examines various issues arising in three-phase unbalanced power distribution networks(PDNs)using a comprehensive optimization approach.With the integration of renewable energy sources,increasing energy dema...This study examines various issues arising in three-phase unbalanced power distribution networks(PDNs)using a comprehensive optimization approach.With the integration of renewable energy sources,increasing energy demands,and the adoption of smart grid technologies,power systems are undergoing a rapid transformation,making the need for efficient,reliable,and sustainable distribution networks increasingly critical.In this paper,the reconfiguration problem in a 37-bus unbalanced PDN test system is solved using five different popular metaheuristic algorithms.Among these advanced search algorithms,the Bonobo Optimizer(BO)has demonstrated superior performance in handling the complexities of unbalanced power distribution network optimization.The study is structured around four distinct scenarios:(Ⅰ)improving mean voltage profile and minimizing active power loss,(Ⅱ)minimizing Voltage Unbalance Index(VUI)and Current Unbalance Index(CUI),(Ⅲ)optimizing key reliability indices using both Line Oriented Reliability Index(LORI)and Customer Oriented Reliability Index(CORI)approaches,and(Ⅳ)employing multi-objective optimization using the Pareto front technique to simultaneously minimize active power loss,average CUI,and System Average Interruption Duration Index(SAIDI).The study aims to contribute to the development of more efficient,reliable,and sustainable energy systems by addressing voltage profiles,power losses,reduction of imbalance,and the enhancement of reliability together.展开更多
A threshold-voltage-based 2-D theoretical model for the Current–Voltage characteristics of the AlGaN/GaN high electron mobility transistors (HEMT’s) is developed. The present work proposes an improved charge-control...A threshold-voltage-based 2-D theoretical model for the Current–Voltage characteristics of the AlGaN/GaN high electron mobility transistors (HEMT’s) is developed. The present work proposes an improved charge-control model by employing the Robin boundary condition when introduced the solution of the 2-D Poisson’s equation in the density of charge depleted in the AlGaN layer. The dependence of 2-DEG sheet carrier concentration on the aluminum composition and AlGaN layer thickness has been investigated in detail. Current–voltage characteristics developed from the 2-DEG model in order to take into account the impact of gate lengths. The relation between the kink effect and existing deep centers has also been confirmed by using an electrical approach, which can allow to adjust some of electron transport parameters in order to optimize the output current.展开更多
Integrated filter circuit design resulted in desire for replacement of Inductors by active elements like Operational Amplifiers which led to the introduction of active filters. Active filter design has evolved over a ...Integrated filter circuit design resulted in desire for replacement of Inductors by active elements like Operational Amplifiers which led to the introduction of active filters. Active filter design has evolved over a period of time. Starting with OP AMPs, we have witnessed phenomenal growth of active component usage in filter design and development catering to varying requirements. This has contributed greatly in emergence of circuits with minimal limitations and advantages in terms of wide Bandwidth and High slew rates. Current Differencing Buffered Amplifier (CDBA) based active filter design has resulted in introduction of many novel circuits .This paper proposes a new Voltage-mode three input and Single output (TISO) multifunction filter based on single CDBA, four resistors and two capacitors. This second order filter circuit is capable of realizing various filter functions by choosing values of the three inputs variably. The natural frequency (ω0) can be tuned with passive components and the Q of the circuit is independent of (ω0) .The higher cascading capability of the circuit is ensured because of its low - output impedance. Further PSPICE-simulated results are in conformity with theoretical values.展开更多
This paper presents an improved finite control set model predictive current control(FCS-MPCC)of a five-phase permanent magnet synchronous motor(PMSM).First,to avoid including all the 32 voltage vectors provided by a t...This paper presents an improved finite control set model predictive current control(FCS-MPCC)of a five-phase permanent magnet synchronous motor(PMSM).First,to avoid including all the 32 voltage vectors provided by a two-level five-phase inverter into the control set,virtual voltage vectors are adopted.As the third current harmonics can be much reduced by virtual voltage vectors automatically,the harmonic items in the cost function of conventional FCS-MPCC are not considered.Furthermore,an adaptive control set is proposed based on voltage prediction.Best control set with proper voltage vector amplitude corresponding to different rotor speed can be achieved by this method.Consequently,current ripples can be largely reduced and the system performs much better.At last,simulations are established to verify the steady and transient performance of the proposed FCS-MPCC,and experiments based on a 2 kW five-phase motor are carried out.The results have validated the performance improvement of the proposed control strategy.展开更多
One configuration for realizing voltage-mode multifunction filters and another configuration for realizing current-mode multifunction filters using current feedback amplifiers (CFAs) are presented. The proposed voltag...One configuration for realizing voltage-mode multifunction filters and another configuration for realizing current-mode multifunction filters using current feedback amplifiers (CFAs) are presented. The proposed voltage-mode circuit exhibit simultaneously lowpass and bandpass filters. The proposed current-mode circuit exhibit simultaneously lowpass, bandpass and highpass filters. The proposed circuits offer the following features: no requirements for component matching conditions;low active and passive sensitivities;employing only grounded capacitors and the ability to obtain multifunction filters from the same circuit configuration.展开更多
In this paper a novel log-domain current-mode integrator based on MOS transistors in subthreshold is proposed. The integrator's time-constant is tunable by varying a reference bias current. By use of the integrato...In this paper a novel log-domain current-mode integrator based on MOS transistors in subthreshold is proposed. The integrator's time-constant is tunable by varying a reference bias current. By use of the integrator, a fifth-order Chebyshev lowpass filter with 0.1dB ripples is designed. The simulation results demonstrate that the proposed filter has such advantages as low power supply(1.5V), very low power dissipation (μW level), nearly ideal frequency response, very small sensitivity to components in passband, and adjustable cut-off frequency over a wide range.The circuit is composed of NMOS transistors and grounded capacitors which make it suitable for fully integrated circuit implementation.展开更多
The critical current density Jc is one of the most important parameters of high temperature superconducting films in superconducting applications, such as superconducting filter and superconducting Josephson devices. ...The critical current density Jc is one of the most important parameters of high temperature superconducting films in superconducting applications, such as superconducting filter and superconducting Josephson devices. This paper presents a new model to describe inhomogeneous current distribution throughout the thickness of superconducting films applying magnetic field by solving the differential equation derived from Maxwell equation and the second London equation. Using this model, it accurately calculates the inductive third-harmonic voltage when the film applying magnetic field with the inductive measurement for Jc. The theoretic curve is consistent with the experimental results about measuring superconducting film, especially when the third-harmonic voltage just exceeds zero. The Jc value of superconducting films determined by the inductive method is also compared with results raeasured by four-probe transport method. The agreements between inductive method and transport method are very good.展开更多
The two-dimensional models for symmetrical double-material double-gate （DM-DG） strained Si （s-Si） metal-oxide semiconductor field effect transistors （MOSFETs） are presented. The surface potential and the surface...The two-dimensional models for symmetrical double-material double-gate （DM-DG） strained Si （s-Si） metal-oxide semiconductor field effect transistors （MOSFETs） are presented. The surface potential and the surface electric field ex- pressions have been obtained by solving Poisson＇s equation. The models of threshold voltage and subthreshold current are obtained based on the surface potential expression. The surface potential and the surface electric field are compared with those of single-material double-gate （SM-DG） MOSFETs. The effects of different device parameters on the threshold voltage and the subthreshold current are demonstrated. The analytical models give deep insight into the device parameters design. The analytical results obtained from the proposed models show good matching with the simulation results using DESSIS.展开更多
Herein,a physical and mathematical model of the voltage−current characteristics of a p−n heterostructure with quantum wells(QWs)is prepared using the Sah−Noyce−Shockley(SNS)recombination mechanism to show the SNS reco...Herein,a physical and mathematical model of the voltage−current characteristics of a p−n heterostructure with quantum wells(QWs)is prepared using the Sah−Noyce−Shockley(SNS)recombination mechanism to show the SNS recombination rate of the correction function of the distribution of QWs in the space charge region of diode configuration.A comparison of the model voltage−current characteristics(VCCs)with the experimental ones reveals their adequacy.The technological parameters of the structure of the VCC model are determined experimentally using a nondestructive capacitive approach for determining the impurity distribution profile in the active region of the diode structure with a profile depth resolution of up to 10Å.The correction function in the expression of the recombination rate shows the possibility of determining the derivative of the VCCs of structures with QWs with a nonideality factor of up to 4.展开更多
This paper proposes an nth order (where n = 2,3, ,n) voltage mode active-C filter using n number of current controlled current conveyors (CCCIIs) and n number of equal valued grounded capacitors. The proposed topology...This paper proposes an nth order (where n = 2,3, ,n) voltage mode active-C filter using n number of current controlled current conveyors (CCCIIs) and n number of equal valued grounded capacitors. The proposed topology can implement both band pass and low pass responses without alteration of any components. The filters offer the following important features: use of minimum number of current controlled current conveyors (CCCIIs) and passive components, no matching constraint, use of all grounded capacitors and absence of external resistor suitable for integration, cut off frequency can easily be electronically adjusted using AMS 0.35 μm CMOS technology. PSPICE simulation results of third order band pass and low pass responses are provided. The results are found to agree well with the theory.展开更多
A novel four-input three-output voltage-mode differential difference current conveyor (DDCC) based universal filter is presented. The circuit uses three DDCCs as active elements, two resistors and two capacitors as pa...A novel four-input three-output voltage-mode differential difference current conveyor (DDCC) based universal filter is presented. The circuit uses three DDCCs as active elements, two resistors and two capacitors as passive elements. The circuit along with its versatility enjoys the advantage of minimum number of passive elements employment. SPICE simulation results are given to confirm the theoretical analysis. The proposed circuit is a novel addition to the existing knowledge on the subject.展开更多
The reverse generation current under high-gate-voltage stress condition in LDD nMOSFET＇s is studied. We find that the generation current peak decreases as the stress time increases. We ascribe this finding to the dom...The reverse generation current under high-gate-voltage stress condition in LDD nMOSFET＇s is studied. We find that the generation current peak decreases as the stress time increases. We ascribe this finding to the dominating oxide trapped electrons that reduce the effective drain bias, lowering the maximal generation rate. The density of the effective trapped electrons affecting the effective drain bias is calculated with our model.展开更多
This paper proposes a zer o current and zero voltage switching (ZCZVS) PWM Boost full bridge (FB) conve rter. With series inductors, the leading switches can realize zero current swit ching (ZCS) in a wide load ra...This paper proposes a zer o current and zero voltage switching (ZCZVS) PWM Boost full bridge (FB) conve rter. With series inductors, the leading switches can realize zero current swit ching (ZCS) in a wide load range using the energy of the output capacitor. Ma king use of parasitic capacitors of the lagging switches and parallel auxiliary i nductance with the primary winding of the transformer, the lagging switches can realize zero voltage switching (ZVS) under any load. Compared with the ZCS PWM Boost FB converter, the new converter has no current duty cycle loss. Operat ional principle and parameter design are analyzed. Experimental results verify the effectiveness of the proposed converter.展开更多
A high performance current and voltage measurement system has been developed in power system. The system is composed of two parts: one current measurement element and one voltage measurement element. A Rogowski coil ...A high performance current and voltage measurement system has been developed in power system. The system is composed of two parts: one current measurement element and one voltage measurement element. A Rogowski coil and a capacitive voltage divider are used respectively for the line current and voltage measurements. Active electronic components are used to modulate signal, and power supply for these components is drawn from power line via an auxiliary current transformer. Measurement signal is transmitted by optical fibers, which is resistant to electromagnetic induction and noise. With careful design and the use of digital signal processing technology, the whole system can meet 0.5% accuracy for metering and provides large dynamic range coupled with good accuracy for protective relaying use.展开更多
In modern rail transportation,inverter drive systems have been extensively used due to their excellent speed control capabilities.However,in recent years,premature failure problems caused by bearing voltage and curren...In modern rail transportation,inverter drive systems have been extensively used due to their excellent speed control capabilities.However,in recent years,premature failure problems caused by bearing voltage and current phenomena have been frequently reported in electric motors,with electrical bearing failures making up a considerable percentage.The purpose of this review is to provide a comprehensive overview of facets relating to the electrical erosion of bearings in an electrical environment represented by railway vehicles.First,the origins of the phenomenon as well as typical bearing electrical failure modes are discussed.Next,we introduce the distinctive features of the electrical environment of railway traction motor bearings,including output voltages with high common-mode components and systems with complex grounding configurations.Then,we classify the fundamental mechanisms for generating bearing voltages/currents into four groups,and present their modeling processes,including equivalent circuit establishment and parameter determination methods.Furthermore,we summarize the strategies frequently used to protect bearings,and describe a typical solution to suppress electrical bearing failures in railway vehicles.Finally,we present a case example to illustrate a research procedure for systematic investigation of inverter-induced bearing currents in rail transportation.展开更多
Nonlinear loads in the power distribution system cause non-sinusoidal currents and voltages with harmonic components.Shunt active filters(SAF) with current controlled voltage source inverters(CCVSI) are usually used t...Nonlinear loads in the power distribution system cause non-sinusoidal currents and voltages with harmonic components.Shunt active filters(SAF) with current controlled voltage source inverters(CCVSI) are usually used to obtain balanced and sinusoidal source currents by injecting compensation currents.However,CCVSI with traditional controllers have a limited transient and steady state performance.In this paper,we propose an adaptive dynamic programming(ADP) controller with online learning capability to improve transient response and harmonics.The proposed controller works alongside existing proportional integral(PI) controllers to efficiently track the reference currents in the d-q domain.It can generate adaptive control actions to compensate the PI controller.The proposed system was simulated under different nonlinear(three-phase full wave rectifier) load conditions.The performance of the proposed approach was compared with the traditional approach.We have also included the simulation results without connecting the traditional PI control based power inverter for reference comparison.The online learning based ADP controller not only reduced average total harmonic distortion by 18.41%,but also outperformed traditional PI controllers during transients.展开更多
In order to investigate the injection current uniformity around the induction cell bores, two fully electromagnetic （EM） models are respectively established for a single-stage induction cell and an induction voltage...In order to investigate the injection current uniformity around the induction cell bores, two fully electromagnetic （EM） models are respectively established for a single-stage induction cell and an induction voltage adder （IVA） with three cells stacked in series, without considering electron emission. By means of these two models, some factors affecting the injection current uni- formity are simulated and analyzed, such as the impedances of adders and loads, cell locations, and feed timing of parallel driving pulses. Simulation results indicate that higher impedances of adder and loads are slightly beneficial to improve injection current uniformity. As the impedances of adder and loads increase from 5 Ω to 30Ω, the asymmetric coefficient of feed currents decreases from 10.3% to 6.6%. The current non-uniformity within the first cell is a little worse than that in other downstream cells. Simulation results also show that the feed timing would greatly affect current waveforms, and consequently cause some distortion in pulse fronts of cell output voltages. For a given driving pulse with duration time of 70-80 ns, the feed timing with a time deviation of less than 20 ns is acceptable for the three-cell IVAs, just causing the rise time of output voltages to increase about 5 ns at most and making the peak voltage decrease by 3.5%.展开更多
An input-output signal selection based on Phillips-Heffron model of a parallel high voltage alternative current/high voltage direct current(HVAC/HVDC) power system is presented to study power system stability. It is w...An input-output signal selection based on Phillips-Heffron model of a parallel high voltage alternative current/high voltage direct current(HVAC/HVDC) power system is presented to study power system stability. It is well known that appropriate coupling of inputs-outputs signals in the multivariable HVDC-HVAC system can improve the performance of designed supplemetary controller. In this work, different analysis techniques are used to measure controllability and observability of electromechanical oscillation mode. Also inputs–outputs interactions are considered and suggestions are drawn to select the best signal pair through the system inputs-outputs. In addition, a supplementary online adaptive controller for nonlinear HVDC to damp low frequency oscillations in a weakly connected system is proposed. The results obtained using MATLAB software show that the best output-input for damping controller design is rotor speed deviation as out put and phase angle of rectifier as in put. Also response of system equipped with adaptive damping controller based on HVDC system has appropriate performance when it is faced with faults and disturbance.展开更多
文摘A design for a Li-ion battery charger IC that can operate in a constant current-constant voltage （CC- CV） charge mode is proposed. In the CC-CV charge mode,the charger IC provides a constant charging current at the beginning, and then the charging current begins to decrease before the battery voltage reaches its final value. After the battery voltage reaches its final value and remains constant,the charging current is further reduced. This approach prevents charging the battery with full current near its saturated voltage,which can cause heating. The novel design of the core of the charger IC realizes the proposed CC-CV charge mode. The chip was implemented in a CSMC 0.6μm CMOS mixed signal process. The experimental results verify the realization of the proposed CC- CV charge mode. The voltage of the battery after charging is 4. 1833V.
基金supported by ITER Program of China(973 Program)(No.2011GB109002)National Natural Science Foundation of China(No.11275056)Hefei University of Technology Doctor Research Foundation of China(No.2011HGBZ1292)
文摘A feedback control system is needed to restrain plasma vertical displacement in EAST （Experimental Advanced Superconducting Toknmak）. A fast control power supply excites active feedback coils, which produces a magnetic field to control the plasma＇s displacement. With the development of EAST, new demands on the new fast control power supply have led to an enhanced ability of fast response and output current, as well as a new control mode. The structure of cascaded and paralleled H-bridges can meet the demand of extended capacity, and digital control can reMize current and voltage mixed control mode. The validity of the proposed scheme is confirmed by experiments.
基金supported by the Scientific and Technological Research Council of Turkey(TUBITAK)under Grant No.124E002(1001-Project).
文摘This study examines various issues arising in three-phase unbalanced power distribution networks(PDNs)using a comprehensive optimization approach.With the integration of renewable energy sources,increasing energy demands,and the adoption of smart grid technologies,power systems are undergoing a rapid transformation,making the need for efficient,reliable,and sustainable distribution networks increasingly critical.In this paper,the reconfiguration problem in a 37-bus unbalanced PDN test system is solved using five different popular metaheuristic algorithms.Among these advanced search algorithms,the Bonobo Optimizer(BO)has demonstrated superior performance in handling the complexities of unbalanced power distribution network optimization.The study is structured around four distinct scenarios:(Ⅰ)improving mean voltage profile and minimizing active power loss,(Ⅱ)minimizing Voltage Unbalance Index(VUI)and Current Unbalance Index(CUI),(Ⅲ)optimizing key reliability indices using both Line Oriented Reliability Index(LORI)and Customer Oriented Reliability Index(CORI)approaches,and(Ⅳ)employing multi-objective optimization using the Pareto front technique to simultaneously minimize active power loss,average CUI,and System Average Interruption Duration Index(SAIDI).The study aims to contribute to the development of more efficient,reliable,and sustainable energy systems by addressing voltage profiles,power losses,reduction of imbalance,and the enhancement of reliability together.
文摘A threshold-voltage-based 2-D theoretical model for the Current–Voltage characteristics of the AlGaN/GaN high electron mobility transistors (HEMT’s) is developed. The present work proposes an improved charge-control model by employing the Robin boundary condition when introduced the solution of the 2-D Poisson’s equation in the density of charge depleted in the AlGaN layer. The dependence of 2-DEG sheet carrier concentration on the aluminum composition and AlGaN layer thickness has been investigated in detail. Current–voltage characteristics developed from the 2-DEG model in order to take into account the impact of gate lengths. The relation between the kink effect and existing deep centers has also been confirmed by using an electrical approach, which can allow to adjust some of electron transport parameters in order to optimize the output current.
文摘Integrated filter circuit design resulted in desire for replacement of Inductors by active elements like Operational Amplifiers which led to the introduction of active filters. Active filter design has evolved over a period of time. Starting with OP AMPs, we have witnessed phenomenal growth of active component usage in filter design and development catering to varying requirements. This has contributed greatly in emergence of circuits with minimal limitations and advantages in terms of wide Bandwidth and High slew rates. Current Differencing Buffered Amplifier (CDBA) based active filter design has resulted in introduction of many novel circuits .This paper proposes a new Voltage-mode three input and Single output (TISO) multifunction filter based on single CDBA, four resistors and two capacitors. This second order filter circuit is capable of realizing various filter functions by choosing values of the three inputs variably. The natural frequency (ω0) can be tuned with passive components and the Q of the circuit is independent of (ω0) .The higher cascading capability of the circuit is ensured because of its low - output impedance. Further PSPICE-simulated results are in conformity with theoretical values.
基金This work was supported in part by the National Natural Science Foundation of China under 61374125。
文摘This paper presents an improved finite control set model predictive current control(FCS-MPCC)of a five-phase permanent magnet synchronous motor(PMSM).First,to avoid including all the 32 voltage vectors provided by a two-level five-phase inverter into the control set,virtual voltage vectors are adopted.As the third current harmonics can be much reduced by virtual voltage vectors automatically,the harmonic items in the cost function of conventional FCS-MPCC are not considered.Furthermore,an adaptive control set is proposed based on voltage prediction.Best control set with proper voltage vector amplitude corresponding to different rotor speed can be achieved by this method.Consequently,current ripples can be largely reduced and the system performs much better.At last,simulations are established to verify the steady and transient performance of the proposed FCS-MPCC,and experiments based on a 2 kW five-phase motor are carried out.The results have validated the performance improvement of the proposed control strategy.
文摘One configuration for realizing voltage-mode multifunction filters and another configuration for realizing current-mode multifunction filters using current feedback amplifiers (CFAs) are presented. The proposed voltage-mode circuit exhibit simultaneously lowpass and bandpass filters. The proposed current-mode circuit exhibit simultaneously lowpass, bandpass and highpass filters. The proposed circuits offer the following features: no requirements for component matching conditions;low active and passive sensitivities;employing only grounded capacitors and the ability to obtain multifunction filters from the same circuit configuration.
文摘In this paper a novel log-domain current-mode integrator based on MOS transistors in subthreshold is proposed. The integrator's time-constant is tunable by varying a reference bias current. By use of the integrator, a fifth-order Chebyshev lowpass filter with 0.1dB ripples is designed. The simulation results demonstrate that the proposed filter has such advantages as low power supply(1.5V), very low power dissipation (μW level), nearly ideal frequency response, very small sensitivity to components in passband, and adjustable cut-off frequency over a wide range.The circuit is composed of NMOS transistors and grounded capacitors which make it suitable for fully integrated circuit implementation.
基金supported by the National High Technology Research and Development Program ('863' Program) of China (Grant No. 2006AA03Z213)
文摘The critical current density Jc is one of the most important parameters of high temperature superconducting films in superconducting applications, such as superconducting filter and superconducting Josephson devices. This paper presents a new model to describe inhomogeneous current distribution throughout the thickness of superconducting films applying magnetic field by solving the differential equation derived from Maxwell equation and the second London equation. Using this model, it accurately calculates the inductive third-harmonic voltage when the film applying magnetic field with the inductive measurement for Jc. The theoretic curve is consistent with the experimental results about measuring superconducting film, especially when the third-harmonic voltage just exceeds zero. The Jc value of superconducting films determined by the inductive method is also compared with results raeasured by four-probe transport method. The agreements between inductive method and transport method are very good.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61376099,11235008,and 61205003)
文摘The two-dimensional models for symmetrical double-material double-gate （DM-DG） strained Si （s-Si） metal-oxide semiconductor field effect transistors （MOSFETs） are presented. The surface potential and the surface electric field ex- pressions have been obtained by solving Poisson＇s equation. The models of threshold voltage and subthreshold current are obtained based on the surface potential expression. The surface potential and the surface electric field are compared with those of single-material double-gate （SM-DG） MOSFETs. The effects of different device parameters on the threshold voltage and the subthreshold current are demonstrated. The analytical models give deep insight into the device parameters design. The analytical results obtained from the proposed models show good matching with the simulation results using DESSIS.
基金conducted within the state assignment of the Ministry of Science and Higher Education for universities(Project No.FZRR-2023-0009).
文摘Herein,a physical and mathematical model of the voltage−current characteristics of a p−n heterostructure with quantum wells(QWs)is prepared using the Sah−Noyce−Shockley(SNS)recombination mechanism to show the SNS recombination rate of the correction function of the distribution of QWs in the space charge region of diode configuration.A comparison of the model voltage−current characteristics(VCCs)with the experimental ones reveals their adequacy.The technological parameters of the structure of the VCC model are determined experimentally using a nondestructive capacitive approach for determining the impurity distribution profile in the active region of the diode structure with a profile depth resolution of up to 10Å.The correction function in the expression of the recombination rate shows the possibility of determining the derivative of the VCCs of structures with QWs with a nonideality factor of up to 4.
文摘This paper proposes an nth order (where n = 2,3, ,n) voltage mode active-C filter using n number of current controlled current conveyors (CCCIIs) and n number of equal valued grounded capacitors. The proposed topology can implement both band pass and low pass responses without alteration of any components. The filters offer the following important features: use of minimum number of current controlled current conveyors (CCCIIs) and passive components, no matching constraint, use of all grounded capacitors and absence of external resistor suitable for integration, cut off frequency can easily be electronically adjusted using AMS 0.35 μm CMOS technology. PSPICE simulation results of third order band pass and low pass responses are provided. The results are found to agree well with the theory.
文摘A novel four-input three-output voltage-mode differential difference current conveyor (DDCC) based universal filter is presented. The circuit uses three DDCCs as active elements, two resistors and two capacitors as passive elements. The circuit along with its versatility enjoys the advantage of minimum number of passive elements employment. SPICE simulation results are given to confirm the theoretical analysis. The proposed circuit is a novel addition to the existing knowledge on the subject.
文摘The reverse generation current under high-gate-voltage stress condition in LDD nMOSFET＇s is studied. We find that the generation current peak decreases as the stress time increases. We ascribe this finding to the dominating oxide trapped electrons that reduce the effective drain bias, lowering the maximal generation rate. The density of the effective trapped electrons affecting the effective drain bias is calculated with our model.
文摘This paper proposes a zer o current and zero voltage switching (ZCZVS) PWM Boost full bridge (FB) conve rter. With series inductors, the leading switches can realize zero current swit ching (ZCS) in a wide load range using the energy of the output capacitor. Ma king use of parasitic capacitors of the lagging switches and parallel auxiliary i nductance with the primary winding of the transformer, the lagging switches can realize zero voltage switching (ZVS) under any load. Compared with the ZCS PWM Boost FB converter, the new converter has no current duty cycle loss. Operat ional principle and parameter design are analyzed. Experimental results verify the effectiveness of the proposed converter.
文摘A high performance current and voltage measurement system has been developed in power system. The system is composed of two parts: one current measurement element and one voltage measurement element. A Rogowski coil and a capacitive voltage divider are used respectively for the line current and voltage measurements. Active electronic components are used to modulate signal, and power supply for these components is drawn from power line via an auxiliary current transformer. Measurement signal is transmitted by optical fibers, which is resistant to electromagnetic induction and noise. With careful design and the use of digital signal processing technology, the whole system can meet 0.5% accuracy for metering and provides large dynamic range coupled with good accuracy for protective relaying use.
基金supported by the National Key R&D Program of China(No.2018YFB1201804)the National Natural Science Foundation of China(Nos.52293424,51827810,and 51977192).
文摘In modern rail transportation,inverter drive systems have been extensively used due to their excellent speed control capabilities.However,in recent years,premature failure problems caused by bearing voltage and current phenomena have been frequently reported in electric motors,with electrical bearing failures making up a considerable percentage.The purpose of this review is to provide a comprehensive overview of facets relating to the electrical erosion of bearings in an electrical environment represented by railway vehicles.First,the origins of the phenomenon as well as typical bearing electrical failure modes are discussed.Next,we introduce the distinctive features of the electrical environment of railway traction motor bearings,including output voltages with high common-mode components and systems with complex grounding configurations.Then,we classify the fundamental mechanisms for generating bearing voltages/currents into four groups,and present their modeling processes,including equivalent circuit establishment and parameter determination methods.Furthermore,we summarize the strategies frequently used to protect bearings,and describe a typical solution to suppress electrical bearing failures in railway vehicles.Finally,we present a case example to illustrate a research procedure for systematic investigation of inverter-induced bearing currents in rail transportation.
文摘Nonlinear loads in the power distribution system cause non-sinusoidal currents and voltages with harmonic components.Shunt active filters(SAF) with current controlled voltage source inverters(CCVSI) are usually used to obtain balanced and sinusoidal source currents by injecting compensation currents.However,CCVSI with traditional controllers have a limited transient and steady state performance.In this paper,we propose an adaptive dynamic programming(ADP) controller with online learning capability to improve transient response and harmonics.The proposed controller works alongside existing proportional integral(PI) controllers to efficiently track the reference currents in the d-q domain.It can generate adaptive control actions to compensate the PI controller.The proposed system was simulated under different nonlinear(three-phase full wave rectifier) load conditions.The performance of the proposed approach was compared with the traditional approach.We have also included the simulation results without connecting the traditional PI control based power inverter for reference comparison.The online learning based ADP controller not only reduced average total harmonic distortion by 18.41%,but also outperformed traditional PI controllers during transients.
基金supported by National Natural Science Foundation of China(No.51307141)partly by the State Key Laboratory of Intense Pulsed Radiation Simulation(Northwest Institute of Nuclear Technology)under Contract SKLIPR 1206
文摘In order to investigate the injection current uniformity around the induction cell bores, two fully electromagnetic （EM） models are respectively established for a single-stage induction cell and an induction voltage adder （IVA） with three cells stacked in series, without considering electron emission. By means of these two models, some factors affecting the injection current uni- formity are simulated and analyzed, such as the impedances of adders and loads, cell locations, and feed timing of parallel driving pulses. Simulation results indicate that higher impedances of adder and loads are slightly beneficial to improve injection current uniformity. As the impedances of adder and loads increase from 5 Ω to 30Ω, the asymmetric coefficient of feed currents decreases from 10.3% to 6.6%. The current non-uniformity within the first cell is a little worse than that in other downstream cells. Simulation results also show that the feed timing would greatly affect current waveforms, and consequently cause some distortion in pulse fronts of cell output voltages. For a given driving pulse with duration time of 70-80 ns, the feed timing with a time deviation of less than 20 ns is acceptable for the three-cell IVAs, just causing the rise time of output voltages to increase about 5 ns at most and making the peak voltage decrease by 3.5%.
文摘An input-output signal selection based on Phillips-Heffron model of a parallel high voltage alternative current/high voltage direct current(HVAC/HVDC) power system is presented to study power system stability. It is well known that appropriate coupling of inputs-outputs signals in the multivariable HVDC-HVAC system can improve the performance of designed supplemetary controller. In this work, different analysis techniques are used to measure controllability and observability of electromechanical oscillation mode. Also inputs–outputs interactions are considered and suggestions are drawn to select the best signal pair through the system inputs-outputs. In addition, a supplementary online adaptive controller for nonlinear HVDC to damp low frequency oscillations in a weakly connected system is proposed. The results obtained using MATLAB software show that the best output-input for damping controller design is rotor speed deviation as out put and phase angle of rectifier as in put. Also response of system equipped with adaptive damping controller based on HVDC system has appropriate performance when it is faced with faults and disturbance.
