The importance of high-performance,low-cost and millimeter-wave transmitters for digital communications and radar applications is increasing.The design and performance of a Ka-band balanced in-phase and quadrature-ph...The importance of high-performance,low-cost and millimeter-wave transmitters for digital communications and radar applications is increasing.The design and performance of a Ka-band balanced in-phase and quadrature-phase（I-Q）type vector modulator,using GaAs heterojunction bipolar transistors（HBTs）as switching elements,are presented.The balanced technique is used to remove the parasitics of the HBTs to result in near perfect constellations.Measurements of the monolithic microwave integrated circuit（MMIC）chip with a size of 1.89×2.26 mm^2 demonstrate an amplitude error below 1.5 dB and the phase error within 3°between 26 and 40 GHz except for a singular point at 35.6 GHz.The results show that the technique is suitable for millimeter-wave digital communications.展开更多
The development of renewable energy power generation for carbon neutrality and energy transition has been increasing worldwide,leading to an increasing demand for high-power conversion.Compared with traditional interl...The development of renewable energy power generation for carbon neutrality and energy transition has been increasing worldwide,leading to an increasing demand for high-power conversion.Compared with traditional interleaved paralleling,the integrated paralleling of three-level inverters can further reduce the output harmonics.Moreover,a well-designed switching sequence ensures that the average circulating current is zero,which provides a superior and feasible solution to satisfy the demands of high-power operations.However,a large instantaneous loop current exists between shunt converters,which leads to disadvantages such as higher switching device stress and loss.In this study,by utilizing the state-distribution redundancy provided by the integrated modulation process,a new design for switch-ing sequences is suggested for the integrated modulation of shunt three-level converters.This design aims to reduce the circulating current while better preserving the same output current harmonics than traditional parallel methods.The proposal includes an in-depth analysis and explanation of the implementation process.Finally,the proposed method is validated through simulations and prototype experi-ments.The results indicate that compared with traditional methods,the adoption of the improved switching sequence presented in this study leads to an average reduction of 3.2%in the total harmonic distortion of the inverter’s output and an average decrease of 32%in the amplitude of the circulating current.Both the output harmonics and circulating currents are significantly suppressed across various modulation indices.展开更多
Three-level neutral point clamped(NPC)inverters have been widely applied in the high voltage and high power drive fields.The capacitance voltage balancing algorithm is a hot topic that many specialists and scholars ha...Three-level neutral point clamped(NPC)inverters have been widely applied in the high voltage and high power drive fields.The capacitance voltage balancing algorithm is a hot topic that many specialists and scholars have been working on.V arious capacitance voltage balancing strategies have been studied,in which the redundant short vectors are not fully utilized.In order to increase the capacitance voltage control effect of the short vectors,a new algorithm is proposed.展开更多
Vector control schemes have recently been used to drive linear induction motors(LIM)in high-performance applications.This trend promotes the development of precise and efficient control schemes for individual motors.T...Vector control schemes have recently been used to drive linear induction motors(LIM)in high-performance applications.This trend promotes the development of precise and efficient control schemes for individual motors.This research aims to present a novel framework for speed and thrust force control of LIM using space vector pulse width modulation(SVPWM)inverters.The framework under consideration is developed in four stages.To begin,MATLAB Simulink was used to develop a detailed mathematical and electromechanical dynamicmodel.The research presents a modified SVPWM inverter control scheme.By tuning the proportional-integral(PI)controller with a transfer function,optimized values for the PI controller are derived.All the subsystems mentioned above are integrated to create a robust simulation of the LIM’s precise speed and thrust force control scheme.The reference speed values were chosen to evaluate the performance of the respective system,and the developed system’s response was verified using various data sets.For the low-speed range,a reference value of 10m/s is used,while a reference value of 100 m/s is used for the high-speed range.The speed output response indicates that themotor reached reference speed in amatter of seconds,as the delay time is between 8 and 10 s.The maximum amplitude of thrust achieved is less than 400N,demonstrating the controller’s capability to control a high-speed LIM with minimal thrust ripple.Due to the controlled speed range,the developed system is highly recommended for low-speed and high-speed and heavy-duty traction applications.展开更多
In order to compensate for the deficiency of Sine Pulse Width Modulation（SPWM）, on the base of analyzing the principle of space w tot pulse width modulation and being compared with SPWM, the method of solving workin...In order to compensate for the deficiency of Sine Pulse Width Modulation（SPWM）, on the base of analyzing the principle of space w tot pulse width modulation and being compared with SPWM, the method of solving working time of adjacent vector and the method of generate space voltage vector were introduced. The experiment to the inverter which consists of IGBT proves that SVPWM centrol algorithm can reduce harmonic effectively, it is beneficial to enhancing the utilization rate of voltage source inverter direct current power supply.展开更多
This paper presents frequency domain method for harmonic analysis of space vector based STATCOM. Space Vector Pulse Width Modulation (SVPWM) method is an advanced PWM method. It is a best method among all the PWM tech...This paper presents frequency domain method for harmonic analysis of space vector based STATCOM. Space Vector Pulse Width Modulation (SVPWM) method is an advanced PWM method. It is a best method among all the PWM techniques. It provides a freedom in a switching cycle for placement space vector. In this paper, the SVPWM is used for switching of STATCOM. The harmonic (or frequency) domain is a steady-state form of harmonic analysis method, which represents converters to their harmonic spectra. This paper presents harmonic analysis by means of harmonic domain for space vector based Static shunt converter (STATCOM). Performance of the STATCOM is evaluated in harmonic domain simulation studies in MATLAB environment.展开更多
This paper presents analytical frequency domain method for harmonic modeling and evaluation of Space Vector Pulse Width Modulation (SVPWM) based static synchronous series converter (SSSC). SVPWM is the best among all ...This paper presents analytical frequency domain method for harmonic modeling and evaluation of Space Vector Pulse Width Modulation (SVPWM) based static synchronous series converter (SSSC). SVPWM is the best among all the PWM techniques. It gives a degree of freedom of space vector placement in a switching cycle. Dynamic modeling technique is used for space vector modulation (SVM) based voltage source converter that is adapted as a static synchronous series converter (SSSC) for harmonic analysis using dynamic harmonic domain. Performance of the SSSC is evaluated in dynamic harmonic domain simulation studies in MATLAB environment. The switching function spectra are necessary for harmonic transfer matrix which is calculated using Fourier series. This paper presents the analysis of harmonics for space vector based SSSC during steady state and dynamic condition.展开更多
Direct torque control (DTC) of Switched reluctance motor is known straightforward control structure with similar execution to that of field situated control strategies. In any case, the part of ideal determination of ...Direct torque control (DTC) of Switched reluctance motor is known straightforward control structure with similar execution to that of field situated control strategies. In any case, the part of ideal determination of the voltage space vector is one of the weakest focuses in a routine DTC drive because of adjustable switching frequency and high torque ripple. In this paper, ideal choice of voltage space vectors is accomplished utilizing ANFIS (Adaptive Neuro Fuzzy Inference System) with space vector Modulation. SVM-DTC gives consistent switching frequency and the proposed ANFIS controller’s structure manages the torque and stator flux error signals through the fuzzy deduction to get a yield that takes the type of space voltage vector. Simulation results accept the proposed evolutionary system with quick torque and flux reaction with minimized torque ripple and flux ripple.展开更多
In this paper, an improved hybrid space vector pulse width modulation (HSVPWM) technique is proposed for IM (induction motor) drives. The basic principle involved in the proposed random pulse width modulation (RPWM) c...In this paper, an improved hybrid space vector pulse width modulation (HSVPWM) technique is proposed for IM (induction motor) drives. The basic principle involved in the proposed random pulse width modulation (RPWM) cuddled SVPWM is amalgamating the pre-calculated switching timings for various sections of hexagonal space vector boundary and the random selection of carrier between two triangular signals, in order to disband acoustic switching noise spectrum with improved fundamental component. The arbitrary selection between triangular carriers, which is decided by digital signal states (Low or High) of the linear feedback shift register (LFSR) based pseudo random binary sequence (PRBS) generator. The SVPWM offers a control degree of freedom in terms of positioning of vectors inside every sampling interval and hence it has six possible variants of the voltage vectors arrangements in each sector. The developed HSVPWM is thoroughly analyzed in using the MATLAB? based simulation for all SVPWM variants. From the simulation and experimental results viz. harmonic spectrum, harmonic spread factor (HSF), total harmonic distortion (THD) etc., and the superiority of the proposed scheme such as better utilization of DC bus and the randomization of the harmonic power are evidenced. For the practical implementation, Xilinx XC3S500E FPGA device has been used.展开更多
Space-vector modulation (SVM) is widely used in multilevel inverters because of its ability to improve DC bus utilization, reduce harmonic distortion, and enhance operational flexibility. However, the increasing compl...Space-vector modulation (SVM) is widely used in multilevel inverters because of its ability to improve DC bus utilization, reduce harmonic distortion, and enhance operational flexibility. However, the increasing complexity of multilevel inverter topologies, such as neutral-point clamped, cascaded H-bridge, and modular multilevel converters, presents challenges in terms of computational efficiency, neutral-point voltage balancing, and common-mode voltage suppression. A detailed review of SVM techniques is provided, including traditional methods and advanced variants such as carrier-based SVM, selective harmonic elimination SVM, and virtual SVM. Additionally, recent hybrid approaches that combine multiple strategies to address specific performance requirements are discussed. The findings highlight advancements in improving the modulation performance, reducing switching losses, and achieving better harmonic attenuation. A discussion of the future challenges and opportunities for multilevel inverter modulation strategies is concluded.展开更多
Imaging the PP- and PS-wave for the elastic vector wave reverse-time migration requires separating the P- and S-waves during the wave field extrapolation. The amplitude and phase of the P- and S-waves are distorted wh...Imaging the PP- and PS-wave for the elastic vector wave reverse-time migration requires separating the P- and S-waves during the wave field extrapolation. The amplitude and phase of the P- and S-waves are distorted when divergence and curl operators are used to separate the P- and S-waves. We present a P- and S-wave amplitude-preserving separation algorithm for the elastic wavefield extrapolation. First, we add the P-wave pressure and P-wave vibration velocity equation to the conventional elastic wave equation to decompose the P- and S-wave vectors. Then, we synthesize the scalar P- and S-wave from the vector P- and S-wave to obtain the scalar P- and S-wave. The amplitude-preserved separated P- and S-waves are imaged based on the vector wave reverse-time migration (RTM). This method ensures that the amplitude and phase of the separated P- and S-wave remain unchanged compared with the divergence and curl operators. In addition, after decomposition, the P-wave pressure and vibration velocity can be used to suppress the interlayer reflection noise and to correct the S-wave polarity. This improves the image quality of P- and S-wave in multicomponent seismic data and the true-amplitude elastic reverse time migration used in prestack inversion.展开更多
Voltage source converter high-voltage direct current （VSC-HVDC） is a new power transmission technology pref- erable in small or medium power transmission. In this paper we discuss a new control system based on space...Voltage source converter high-voltage direct current （VSC-HVDC） is a new power transmission technology pref- erable in small or medium power transmission. In this paper we discuss a new control system based on space vector modulation （SVM） without any voltage line sensors. Using direct power control （DPC） SVM and a new double synchronous reference frame phase-locked loop （DSRF-PLL） approach, the control system is resistant to the majority of line voltage disturbances. Also, the system response has accelerated by using a feed forward power decoupled loop. The operation of this control strategy was verified in a SIMULINK/MATLAB simulation environment. To validate this control system, a 5 kV.A prototype system was constructed. Compared to the original controllers, the current total harmonic distortion （THD）, the active and reactive deviations and the DC voltage overshoot were lowered by 2.5%, 6.2% and 8%, respectively. The rectifier power factor in the worst condition was 0.93 and the DC voltage settling time was 0.2 s.展开更多
Rising concern in environmental issues on global scale has made energy saving in powered equipment a very important subject.In order to improve the energy efficiency and driving range of a motor hoist,a regenerative b...Rising concern in environmental issues on global scale has made energy saving in powered equipment a very important subject.In order to improve the energy efficiency and driving range of a motor hoist,a regenerative braking system is designed and discussed.The system takes a unique ultracapacitor-only approach to energy storage system.The bi-directional bride DC？DC converter which regulates current flow to and from the ultracapacitor operates in two modes：boost and buck,depending on the direction of the flow.In order to provide constant input and output current at the ultracapacitor,this system uses a double proportional-integral（PI） control strategy in regulating the duty cycle of PWM to the DC？DC converter.The permanent magnet synchronous motor（PWSM） drive system is also studied.The space vector pulse width modulation（SVPWM） technique,along with a two-closed-loop vector control model,is adopted after detailed analysis of PMSM characteristics.The overall model and control strategy for this regenerative braking system is ultimately built and simulated under the MATLAB and Simulink environment.A test platform is built to obtain experimental results.Analysis of the results reveals that more than half of the gravitational potential energy can be recovered by this system.Simulation and experimentation results testify the validity of the double PI control strategy for interface circuit of ultracapacitor and SVPWM strategy for PMSM.展开更多
In wind power generation system the grid-connected inverter is an important section for energy conversion and transmission, of which the performance has a direct influence on the entire wind power generation system. T...In wind power generation system the grid-connected inverter is an important section for energy conversion and transmission, of which the performance has a direct influence on the entire wind power generation system. The mathematical model of the grid-connected inverter is deduced firstly. Then, the space vector pulse width modulation （SVPWM） is analyzed. The power factor can be controlled close to unity, leading or lagging, which is realized based on H-type current controller and grid voltage vector-oriented control. The control strategy is verified by the simulation and experimental results with a good sinusoidal current, a small harmonic component and a fast dynamic response.展开更多
In the traditional three-level space vector pulse width modulation(SVPWM)algorithm,the sector judgment is computationallycomplex since the sector is divided into triangles and hexagons.In addition,the switching freque...In the traditional three-level space vector pulse width modulation(SVPWM)algorithm,the sector judgment is computationallycomplex since the sector is divided into triangles and hexagons.In addition,the switching frequency is high becausethe seven-segment switching sequence is adopted.For this reason,a new SVPWM control algorithm for three-level inverteris proposed,in which the sector judgment is simplified by dividing the sector into quasi hexagons?and the new four-segmentswitching sequence is adopted to reduce the switching frequency.Simulation results show that the total harmonic distortiongrows down with the switching frequency decreasing,moreover,the algorithm runtime is also decreased.展开更多
The topology of diode neutral-point-clamped(NPC)three-level inverter is prone to neutral-point potential offset.When the sum of three-phase current is zero,the virtual space vector pulse width modulation(VSVPWM)scheme...The topology of diode neutral-point-clamped(NPC)three-level inverter is prone to neutral-point potential offset.When the sum of three-phase current is zero,the virtual space vector pulse width modulation(VSVPWM)scheme does not cause the neutral-point voltage offset,but it lacks the ability to balance the deviation.For this reason,a neutral-point potential control strategy combining virtual space vector modulation and loop width control is proposed.The neutral-point potential is balanced by introducing the distribution factor for the regions with redundant vectors.For other regions,the potential is controlled by selecting a suitable switching sequence.Meanwhile,the effect on the virtual vector modulation is reduced within the loop width by setting an appropriate loop width,thereby improving the balance effect.The simulation results show that the proposed method has a strong ability to control the offset and has excellent potential balance performance under the conditions of balanced load,unbalanced load and asymmetric capacitance parameters.展开更多
This paper introduces the principle of space vector pulse width modulation （SVPWM）, and discusses a method for implementing the SVPWM based on MATLAB/SIMULINK, as well as modeling of AC servo system with permanent m...This paper introduces the principle of space vector pulse width modulation （SVPWM）, and discusses a method for implementing the SVPWM based on MATLAB/SIMULINK, as well as modeling of AC servo system with permanent magnet synchronous motor （PMSM）. Simulation results show that the model is effective, and the method provides a frame of reference for software and hardware designs which can be applied in high temperature superconducting （HTS） flywheel energy storage system （FESS） and linear motor （LM）.展开更多
Arbitrary waveform can be synthesized by two orthogonal components: in-phase and quadrature components. Thus, if we can manipulate the two components independently, various complicated modulation can be achieved. This...Arbitrary waveform can be synthesized by two orthogonal components: in-phase and quadrature components. Thus, if we can manipulate the two components independently, various complicated modulation can be achieved. This technique is called vector modulation, which is commonly used in wireless radio communication systems where the carrier frequency is lower than 100GHz. On the other hand, in lightwave transmission systems, the carrier frequency is higher than 100THz, and the stability of the signal sources would be much poorer than in radio systems, so that the simplest modulation format (on-off-keying) was often used in commercial systems. However, recently, various modulation techniques such as quadrature amplitude modulation, etc., have been demonstrated by using precise and rapid lightwave control. In this report, we review recent progress in optical vector modulation technologies which can generate highspeed and complicated optical signals. Integrated optical modulators can synthesize multi-level signals in photonic circuits.展开更多
Three space vector pulse width modulation （SVPWM） schemes, called 7-segment space vector modulation （SVM）, 5-segment SVM and 3-segment SVM are studied in this paper. The basic principle of SVPWM is presented. The ...Three space vector pulse width modulation （SVPWM） schemes, called 7-segment space vector modulation （SVM）, 5-segment SVM and 3-segment SVM are studied in this paper. The basic principle of SVPWM is presented. The switching sequence of different scheme is described. The modulation signals, DC bus voltage utilization, and output line voltage harmonic of these schemes are analyzed by the MATLAB software with different modulation index M and frequency modulation index N. The simulation results are analyzed and show that discontinuous modulating functions lead a reduction of switching actions. The DC bus voltage utilization of three schemes is almost the same. For all three SVM, the frequency modulation index N will affect the harmonic characteristic, and the modulation index M will affect DC bus voltage utilization and the harmonic content. The experiment is implemented by the DSP of TMS320F2812. The results validate three algorithms and the simulation.展开更多
Any nonlinear behavior of the system is analyzed by a useful way of Total Harmonic Distortion(THD)technique.Reduced THD achieves lower peak current,higher efficiency and longer equipment life span.Simulated annealing(S...Any nonlinear behavior of the system is analyzed by a useful way of Total Harmonic Distortion(THD)technique.Reduced THD achieves lower peak current,higher efficiency and longer equipment life span.Simulated annealing(SA)is applied due to the effectiveness of locating solutions that are close to ideal and to challenge large-scale combinatorial optimization for Permanent Magnet Synchronous Machine(PMSM).The parameters of direct torque controllers(DTC)for the drive are automatically adjusted by the optimization algorithm.Advantages of the PI-Fuzzy-SA algorithm are retained when used together.It also improves the rate of system convergence.Speed response improvement and har-monic reduction is achieved with SA-based DTC for PMSM.This mechanism is known to be faster than other algorithms.Also,it is observed that as compared to other algorithms,the projected algorithm yields a reduced total harmonic distor-tion.As a result of the employment of Space Vector Modulation(SVM)techni-que,the system is resistant to changes in motor specifications and load torque.Through MATLAB&Simulink simulation,the experiment is done and the per-formance is calculated for the controller.展开更多
基金Project supported by the State Key Development Program for Basic Research of China(No2010CB327505)
文摘The importance of high-performance,low-cost and millimeter-wave transmitters for digital communications and radar applications is increasing.The design and performance of a Ka-band balanced in-phase and quadrature-phase（I-Q）type vector modulator,using GaAs heterojunction bipolar transistors（HBTs）as switching elements,are presented.The balanced technique is used to remove the parasitics of the HBTs to result in near perfect constellations.Measurements of the monolithic microwave integrated circuit（MMIC）chip with a size of 1.89×2.26 mm^2 demonstrate an amplitude error below 1.5 dB and the phase error within 3°between 26 and 40 GHz except for a singular point at 35.6 GHz.The results show that the technique is suitable for millimeter-wave digital communications.
基金supported by the National Natural Science Foundation of China(Grant No.51977046)Wuxi University Research Start-up Fund for Introduced Talent(2022r021).
文摘The development of renewable energy power generation for carbon neutrality and energy transition has been increasing worldwide,leading to an increasing demand for high-power conversion.Compared with traditional interleaved paralleling,the integrated paralleling of three-level inverters can further reduce the output harmonics.Moreover,a well-designed switching sequence ensures that the average circulating current is zero,which provides a superior and feasible solution to satisfy the demands of high-power operations.However,a large instantaneous loop current exists between shunt converters,which leads to disadvantages such as higher switching device stress and loss.In this study,by utilizing the state-distribution redundancy provided by the integrated modulation process,a new design for switch-ing sequences is suggested for the integrated modulation of shunt three-level converters.This design aims to reduce the circulating current while better preserving the same output current harmonics than traditional parallel methods.The proposal includes an in-depth analysis and explanation of the implementation process.Finally,the proposed method is validated through simulations and prototype experi-ments.The results indicate that compared with traditional methods,the adoption of the improved switching sequence presented in this study leads to an average reduction of 3.2%in the total harmonic distortion of the inverter’s output and an average decrease of 32%in the amplitude of the circulating current.Both the output harmonics and circulating currents are significantly suppressed across various modulation indices.
文摘Three-level neutral point clamped(NPC)inverters have been widely applied in the high voltage and high power drive fields.The capacitance voltage balancing algorithm is a hot topic that many specialists and scholars have been working on.V arious capacitance voltage balancing strategies have been studied,in which the redundant short vectors are not fully utilized.In order to increase the capacitance voltage control effect of the short vectors,a new algorithm is proposed.
基金The authors extend their appreciation to the Deanship of Scientific Research at King Khalid University for funding this work through Large Groups Project under grant number(RGP.2/111/43).
文摘Vector control schemes have recently been used to drive linear induction motors(LIM)in high-performance applications.This trend promotes the development of precise and efficient control schemes for individual motors.This research aims to present a novel framework for speed and thrust force control of LIM using space vector pulse width modulation(SVPWM)inverters.The framework under consideration is developed in four stages.To begin,MATLAB Simulink was used to develop a detailed mathematical and electromechanical dynamicmodel.The research presents a modified SVPWM inverter control scheme.By tuning the proportional-integral(PI)controller with a transfer function,optimized values for the PI controller are derived.All the subsystems mentioned above are integrated to create a robust simulation of the LIM’s precise speed and thrust force control scheme.The reference speed values were chosen to evaluate the performance of the respective system,and the developed system’s response was verified using various data sets.For the low-speed range,a reference value of 10m/s is used,while a reference value of 100 m/s is used for the high-speed range.The speed output response indicates that themotor reached reference speed in amatter of seconds,as the delay time is between 8 and 10 s.The maximum amplitude of thrust achieved is less than 400N,demonstrating the controller’s capability to control a high-speed LIM with minimal thrust ripple.Due to the controlled speed range,the developed system is highly recommended for low-speed and high-speed and heavy-duty traction applications.
文摘In order to compensate for the deficiency of Sine Pulse Width Modulation（SPWM）, on the base of analyzing the principle of space w tot pulse width modulation and being compared with SPWM, the method of solving working time of adjacent vector and the method of generate space voltage vector were introduced. The experiment to the inverter which consists of IGBT proves that SVPWM centrol algorithm can reduce harmonic effectively, it is beneficial to enhancing the utilization rate of voltage source inverter direct current power supply.
文摘This paper presents frequency domain method for harmonic analysis of space vector based STATCOM. Space Vector Pulse Width Modulation (SVPWM) method is an advanced PWM method. It is a best method among all the PWM techniques. It provides a freedom in a switching cycle for placement space vector. In this paper, the SVPWM is used for switching of STATCOM. The harmonic (or frequency) domain is a steady-state form of harmonic analysis method, which represents converters to their harmonic spectra. This paper presents harmonic analysis by means of harmonic domain for space vector based Static shunt converter (STATCOM). Performance of the STATCOM is evaluated in harmonic domain simulation studies in MATLAB environment.
文摘This paper presents analytical frequency domain method for harmonic modeling and evaluation of Space Vector Pulse Width Modulation (SVPWM) based static synchronous series converter (SSSC). SVPWM is the best among all the PWM techniques. It gives a degree of freedom of space vector placement in a switching cycle. Dynamic modeling technique is used for space vector modulation (SVM) based voltage source converter that is adapted as a static synchronous series converter (SSSC) for harmonic analysis using dynamic harmonic domain. Performance of the SSSC is evaluated in dynamic harmonic domain simulation studies in MATLAB environment. The switching function spectra are necessary for harmonic transfer matrix which is calculated using Fourier series. This paper presents the analysis of harmonics for space vector based SSSC during steady state and dynamic condition.
文摘Direct torque control (DTC) of Switched reluctance motor is known straightforward control structure with similar execution to that of field situated control strategies. In any case, the part of ideal determination of the voltage space vector is one of the weakest focuses in a routine DTC drive because of adjustable switching frequency and high torque ripple. In this paper, ideal choice of voltage space vectors is accomplished utilizing ANFIS (Adaptive Neuro Fuzzy Inference System) with space vector Modulation. SVM-DTC gives consistent switching frequency and the proposed ANFIS controller’s structure manages the torque and stator flux error signals through the fuzzy deduction to get a yield that takes the type of space voltage vector. Simulation results accept the proposed evolutionary system with quick torque and flux reaction with minimized torque ripple and flux ripple.
文摘In this paper, an improved hybrid space vector pulse width modulation (HSVPWM) technique is proposed for IM (induction motor) drives. The basic principle involved in the proposed random pulse width modulation (RPWM) cuddled SVPWM is amalgamating the pre-calculated switching timings for various sections of hexagonal space vector boundary and the random selection of carrier between two triangular signals, in order to disband acoustic switching noise spectrum with improved fundamental component. The arbitrary selection between triangular carriers, which is decided by digital signal states (Low or High) of the linear feedback shift register (LFSR) based pseudo random binary sequence (PRBS) generator. The SVPWM offers a control degree of freedom in terms of positioning of vectors inside every sampling interval and hence it has six possible variants of the voltage vectors arrangements in each sector. The developed HSVPWM is thoroughly analyzed in using the MATLAB? based simulation for all SVPWM variants. From the simulation and experimental results viz. harmonic spectrum, harmonic spread factor (HSF), total harmonic distortion (THD) etc., and the superiority of the proposed scheme such as better utilization of DC bus and the randomization of the harmonic power are evidenced. For the practical implementation, Xilinx XC3S500E FPGA device has been used.
文摘Space-vector modulation (SVM) is widely used in multilevel inverters because of its ability to improve DC bus utilization, reduce harmonic distortion, and enhance operational flexibility. However, the increasing complexity of multilevel inverter topologies, such as neutral-point clamped, cascaded H-bridge, and modular multilevel converters, presents challenges in terms of computational efficiency, neutral-point voltage balancing, and common-mode voltage suppression. A detailed review of SVM techniques is provided, including traditional methods and advanced variants such as carrier-based SVM, selective harmonic elimination SVM, and virtual SVM. Additionally, recent hybrid approaches that combine multiple strategies to address specific performance requirements are discussed. The findings highlight advancements in improving the modulation performance, reducing switching losses, and achieving better harmonic attenuation. A discussion of the future challenges and opportunities for multilevel inverter modulation strategies is concluded.
基金supported by Special Research Grant for Non-profit Public Service(No.201511037)National Natural Science Foundation of China(No.41504109,41506084,and 41406071)+1 种基金China Postdoctoral Science Foundation(No.2015M582060)Qingdao Municipal Applied Research Projects(No.2015308)
文摘Imaging the PP- and PS-wave for the elastic vector wave reverse-time migration requires separating the P- and S-waves during the wave field extrapolation. The amplitude and phase of the P- and S-waves are distorted when divergence and curl operators are used to separate the P- and S-waves. We present a P- and S-wave amplitude-preserving separation algorithm for the elastic wavefield extrapolation. First, we add the P-wave pressure and P-wave vibration velocity equation to the conventional elastic wave equation to decompose the P- and S-wave vectors. Then, we synthesize the scalar P- and S-wave from the vector P- and S-wave to obtain the scalar P- and S-wave. The amplitude-preserved separated P- and S-waves are imaged based on the vector wave reverse-time migration (RTM). This method ensures that the amplitude and phase of the separated P- and S-wave remain unchanged compared with the divergence and curl operators. In addition, after decomposition, the P-wave pressure and vibration velocity can be used to suppress the interlayer reflection noise and to correct the S-wave polarity. This improves the image quality of P- and S-wave in multicomponent seismic data and the true-amplitude elastic reverse time migration used in prestack inversion.
文摘Voltage source converter high-voltage direct current （VSC-HVDC） is a new power transmission technology pref- erable in small or medium power transmission. In this paper we discuss a new control system based on space vector modulation （SVM） without any voltage line sensors. Using direct power control （DPC） SVM and a new double synchronous reference frame phase-locked loop （DSRF-PLL） approach, the control system is resistant to the majority of line voltage disturbances. Also, the system response has accelerated by using a feed forward power decoupled loop. The operation of this control strategy was verified in a SIMULINK/MATLAB simulation environment. To validate this control system, a 5 kV.A prototype system was constructed. Compared to the original controllers, the current total harmonic distortion （THD）, the active and reactive deviations and the DC voltage overshoot were lowered by 2.5%, 6.2% and 8%, respectively. The rectifier power factor in the worst condition was 0.93 and the DC voltage settling time was 0.2 s.
基金supported by National Key Technology Research and Development Program of China (Grant No. 2007BAF10B00)
文摘Rising concern in environmental issues on global scale has made energy saving in powered equipment a very important subject.In order to improve the energy efficiency and driving range of a motor hoist,a regenerative braking system is designed and discussed.The system takes a unique ultracapacitor-only approach to energy storage system.The bi-directional bride DC？DC converter which regulates current flow to and from the ultracapacitor operates in two modes：boost and buck,depending on the direction of the flow.In order to provide constant input and output current at the ultracapacitor,this system uses a double proportional-integral（PI） control strategy in regulating the duty cycle of PWM to the DC？DC converter.The permanent magnet synchronous motor（PWSM） drive system is also studied.The space vector pulse width modulation（SVPWM） technique,along with a two-closed-loop vector control model,is adopted after detailed analysis of PMSM characteristics.The overall model and control strategy for this regenerative braking system is ultimately built and simulated under the MATLAB and Simulink environment.A test platform is built to obtain experimental results.Analysis of the results reveals that more than half of the gravitational potential energy can be recovered by this system.Simulation and experimentation results testify the validity of the double PI control strategy for interface circuit of ultracapacitor and SVPWM strategy for PMSM.
基金supported by Delta Power Electronic Science and Education Development in 2007 (Grant No.DRES2007002)
文摘In wind power generation system the grid-connected inverter is an important section for energy conversion and transmission, of which the performance has a direct influence on the entire wind power generation system. The mathematical model of the grid-connected inverter is deduced firstly. Then, the space vector pulse width modulation （SVPWM） is analyzed. The power factor can be controlled close to unity, leading or lagging, which is realized based on H-type current controller and grid voltage vector-oriented control. The control strategy is verified by the simulation and experimental results with a good sinusoidal current, a small harmonic component and a fast dynamic response.
基金National Natural Science Foundation of China(No.61261029)
文摘In the traditional three-level space vector pulse width modulation(SVPWM)algorithm,the sector judgment is computationallycomplex since the sector is divided into triangles and hexagons.In addition,the switching frequency is high becausethe seven-segment switching sequence is adopted.For this reason,a new SVPWM control algorithm for three-level inverteris proposed,in which the sector judgment is simplified by dividing the sector into quasi hexagons?and the new four-segmentswitching sequence is adopted to reduce the switching frequency.Simulation results show that the total harmonic distortiongrows down with the switching frequency decreasing,moreover,the algorithm runtime is also decreased.
基金National Natural Science Foundation of China(No.61761027)Postgraduate Education Reform Project of Lanzhou Jiaotong University(No.1600120101)
文摘The topology of diode neutral-point-clamped(NPC)three-level inverter is prone to neutral-point potential offset.When the sum of three-phase current is zero,the virtual space vector pulse width modulation(VSVPWM)scheme does not cause the neutral-point voltage offset,but it lacks the ability to balance the deviation.For this reason,a neutral-point potential control strategy combining virtual space vector modulation and loop width control is proposed.The neutral-point potential is balanced by introducing the distribution factor for the regions with redundant vectors.For other regions,the potential is controlled by selecting a suitable switching sequence.Meanwhile,the effect on the virtual vector modulation is reduced within the loop width by setting an appropriate loop width,thereby improving the balance effect.The simulation results show that the proposed method has a strong ability to control the offset and has excellent potential balance performance under the conditions of balanced load,unbalanced load and asymmetric capacitance parameters.
基金This workis supported by the Chinese High Technology Development Plan Projectunder Grant No. 2007AA03Z208.
文摘This paper introduces the principle of space vector pulse width modulation （SVPWM）, and discusses a method for implementing the SVPWM based on MATLAB/SIMULINK, as well as modeling of AC servo system with permanent magnet synchronous motor （PMSM）. Simulation results show that the model is effective, and the method provides a frame of reference for software and hardware designs which can be applied in high temperature superconducting （HTS） flywheel energy storage system （FESS） and linear motor （LM）.
文摘Arbitrary waveform can be synthesized by two orthogonal components: in-phase and quadrature components. Thus, if we can manipulate the two components independently, various complicated modulation can be achieved. This technique is called vector modulation, which is commonly used in wireless radio communication systems where the carrier frequency is lower than 100GHz. On the other hand, in lightwave transmission systems, the carrier frequency is higher than 100THz, and the stability of the signal sources would be much poorer than in radio systems, so that the simplest modulation format (on-off-keying) was often used in commercial systems. However, recently, various modulation techniques such as quadrature amplitude modulation, etc., have been demonstrated by using precise and rapid lightwave control. In this report, we review recent progress in optical vector modulation technologies which can generate highspeed and complicated optical signals. Integrated optical modulators can synthesize multi-level signals in photonic circuits.
基金This work was supported by the Research Fund for the Doctoral Program of Higher Education of China under Grant No. 20050487044.
文摘Three space vector pulse width modulation （SVPWM） schemes, called 7-segment space vector modulation （SVM）, 5-segment SVM and 3-segment SVM are studied in this paper. The basic principle of SVPWM is presented. The switching sequence of different scheme is described. The modulation signals, DC bus voltage utilization, and output line voltage harmonic of these schemes are analyzed by the MATLAB software with different modulation index M and frequency modulation index N. The simulation results are analyzed and show that discontinuous modulating functions lead a reduction of switching actions. The DC bus voltage utilization of three schemes is almost the same. For all three SVM, the frequency modulation index N will affect the harmonic characteristic, and the modulation index M will affect DC bus voltage utilization and the harmonic content. The experiment is implemented by the DSP of TMS320F2812. The results validate three algorithms and the simulation.
文摘Any nonlinear behavior of the system is analyzed by a useful way of Total Harmonic Distortion(THD)technique.Reduced THD achieves lower peak current,higher efficiency and longer equipment life span.Simulated annealing(SA)is applied due to the effectiveness of locating solutions that are close to ideal and to challenge large-scale combinatorial optimization for Permanent Magnet Synchronous Machine(PMSM).The parameters of direct torque controllers(DTC)for the drive are automatically adjusted by the optimization algorithm.Advantages of the PI-Fuzzy-SA algorithm are retained when used together.It also improves the rate of system convergence.Speed response improvement and har-monic reduction is achieved with SA-based DTC for PMSM.This mechanism is known to be faster than other algorithms.Also,it is observed that as compared to other algorithms,the projected algorithm yields a reduced total harmonic distor-tion.As a result of the employment of Space Vector Modulation(SVM)techni-que,the system is resistant to changes in motor specifications and load torque.Through MATLAB&Simulink simulation,the experiment is done and the per-formance is calculated for the controller.
