The two-phase flow in porous media is affected by multiple factors.In the present study,a two-dimensional numerical model of porous media was developed using the actual pore structure of the core sample.The phase fiel...The two-phase flow in porous media is affected by multiple factors.In the present study,a two-dimensional numerical model of porous media was developed using the actual pore structure of the core sample.The phase field method was utilized to simulate the impact of displacement velocity,the water-gas viscosity ratio,and the density ratio on the flow behavior of two-phase fluids in porous media.The effectiveness of displacement was evaluated by analyzing CO_(2)saturation levels.The results indicate that the saturation of CO_(2)in porous media increased as the displacement velocity increased.When the displacement velocity exceeded 0.01 m/s,there was a corresponding increase in CO_(2)saturation.Conversely,when the displacement velocity was below this threshold,the impact on CO_(2)saturation was minimal.An“inflection point,”M3,was present in the viscosity ratio.When the viscosity of CO_(2)is less than 8.937×10^(-5)Pa·s(viscosity ratio below M3),variations in the viscosity of CO_(2)had little impact on its saturation.Conversely,when the viscosity of CO_(2)exceeded 8.937×10^(-5)Pa·s(viscosity ratio greater than M3),saturation increased with an increase in the viscosity ratio.In terms of the density ratio,the saturation of CO_(2)increased monotonically with an increase in the density ratio.Similarly,increasing density ratios resulted in a monotonic increase in CO_(2)saturation,though this trend was less pronounced in numerical simulations.Analysis results of displacement within dead-end pores using pressure and velocity diagrams reveal eddy currents as contributing factors.Finally,the impact of pore throat structure on the formation of dominant channels was examined.展开更多
A mathematical model of two-phase fluid nonlinear flow in the direction of normal of ellipse through low-permeability porous media was established according to a nonlinear flow law expressed in a continuous function w...A mathematical model of two-phase fluid nonlinear flow in the direction of normal of ellipse through low-permeability porous media was established according to a nonlinear flow law expressed in a continuous function with three parameters, a mass conservation law and a concept of turbulent ellipses. A solution to the model was obtained by using a finite difference method and an extrapolation method. Formulas of calculating development index not only before but also after water breaks through an oil well in the condition of two-phase fluid nonlinear flow in the media were derived. An example was discussed. Water saturation distribution was presented. The moving law of drainage front was found. Laws of change of pressure difference with time were recognized. Results show that there is much difference of water saturation distribution between nonlinear flow and linear flow; that drainage front by water moves faster, water breaks through sooner and the index gets worse because of the nonlinear flow; and that dimensionless pressure difference gets larger at the same dimensionless time and difficulty of oil development becomes bigger by the nonlinear flow. Thus, it is necessary that influence of nonlinear flow on development indexes of the oil fields be taken into account. The results provide water-flooding development of the oilfields with scientific basis.展开更多
Climate change is a reality. The burning of fossil fuels from oil, natural gas and coal is responsible for much of the pollution and the increase in the planet’s average temperature, which has raised discussions on t...Climate change is a reality. The burning of fossil fuels from oil, natural gas and coal is responsible for much of the pollution and the increase in the planet’s average temperature, which has raised discussions on the subject, given the emergencies related to climate. An energy transition to clean and renewable sources is necessary and urgent, but it will not be quick. In this sense, increasing the efficiency of oil extraction from existing sources is crucial, to avoid waste and the drilling of new wells. The purpose of this work was to add diffusive and dispersive terms to the Buckley-Leverett equation in order to incorporate extra phenomena in the temporal evolution between the water-oil and oil-water transitions in the pipeline. For this, the modified Buckley-Leverett equation was discretized via essentially weighted non-oscillatory schemes, coupled with a three-stage Runge-Kutta and a fourth-order centered finite difference methods. Then, computational simulations were performed and the results showed that new features emerge in the transitions, when compared to classical simulations. For instance, the dispersive term inhibits the diffusive term, adding oscillations, which indicates that the absorption of the fluid by the porous medium occurs in a non-homogeneous manner. Therefore, based on research such as this, decisions can be made regarding the replacement of the porous medium or the insertion of new components to delay the replacement.展开更多
The corrosion behavior of type 1045（AISI） carbon steel（CS） in oil-water fluids was investigated by considering the surface wetting state as the breakthrough point.The surface water wetting percentage（SWWP）and co...The corrosion behavior of type 1045（AISI） carbon steel（CS） in oil-water fluids was investigated by considering the surface wetting state as the breakthrough point.The surface water wetting percentage（SWWP）and corrosion weight loss of CS in different oil-water fluids were measured.The morphology and composition of the corrosion films were detected via scanning electron microscopy,electron-probe facescanning technology and Fourier-transform infrared spectroscopy.The results indicated that the corrosion weight loss of CS in the oil-water fluids corresponded with SWWP and that the corrosion process was influenced by the participation of oil.展开更多
Equations of motion for bubble collapse in solid-liquid two-phase fluid have been derived, in which the resistance coupling effects between the liquid and solid particles have been considered. The motion of particles ...Equations of motion for bubble collapse in solid-liquid two-phase fluid have been derived, in which the resistance coupling effects between the liquid and solid particles have been considered. The motion of particles during the bubble collapse and the effects of particles on bubble collapse have been calculated and discussed. Qualitative relations between the concentration and the size of the particles and the rate of bubble collapse have been obtaind.展开更多
Research interests have recently been directed towards electrical discharges in multi-phase environments.Natural electrical discharges,such as lightning and coronas,occur in the Earth＇s atmosphere,which is actually a...Research interests have recently been directed towards electrical discharges in multi-phase environments.Natural electrical discharges,such as lightning and coronas,occur in the Earth＇s atmosphere,which is actually a mixture of gaseous phase（air） and suspended solid and liquid particulate matters（PMs）.An example of an anthropogenic gaseous multi-phase environment is the flow of flue gas through electrostatic precipitators（ESPs）,which are generally regarded as a mixture of a post-combustion gas with solid PM and microdroplets suspended in it.Electrical discharges in multi-phase environments,the knowledge of which is scarce,are becoming an attractive research subject,offering a wide variety of possible discharges and multi-phase environments to be studied.This paper is an introduction to electrical discharges in multi-phase environments.It is focused on DC negative coronas and accompanying electrohydrodynamic（EHD） flows in a gaseous two-phase fluid formed by air（a gaseous phase） and solid PM（a solid phase）,run under laboratory conditions.The introduction is based on a review of the relevant literature.Two cases will be considered：the first case is of a gaseous two-phase fluid,initially motionless in a closed chamber before being subjected to a negative corona（with the needle-toplate electrode arrangement）,which afterwards induces an EHD flow in the chamber,and the second,of a gaseous two-phase fluid flowing transversely with respect to the needle-to-plate electrode axis along a chamber with a corona discharge running between the electrodes.This review-based introductory paper should be of interest to theoretical researchers and modellers in the field of negative corona discharges in single-or two-phase fluids,and for engineers who work on designing EHD devices（such as ESPs,EHD pumps,and smoke detectors）.展开更多
This paper introduces a 100 MPa water gas twophase fluid pressurization device.The device can provide 100 MPa gas pressure and 200 MPa liquid pressure for small volume(<20 mL)high-pressure experimental devices.This...This paper introduces a 100 MPa water gas twophase fluid pressurization device.The device can provide 100 MPa gas pressure and 200 MPa liquid pressure for small volume(<20 mL)high-pressure experimental devices.This device can make the pressure control independent of the temperature control without changing the material components of the system.The resolution of this device in adjusting the pressure is±0.2 MPa in the process of boosting and depressurizing.This pressure boosting device generates very little vibration during work and it can be used in experiments with strict requirements on vibration.As a thermodynamic parameter,pressure has a great influence on matter.In the field of experimental geochemistry,pressure is not only an experimental method and an extreme condition but an important physical parameter independent of temperature and chemical composition.展开更多
Underwater gas-liquid two-phase propulsion technology is an emerging propulsion method that offers high efficiency and unrestricted navigation speed.The integration of this technology into water ramjet engines can sig...Underwater gas-liquid two-phase propulsion technology is an emerging propulsion method that offers high efficiency and unrestricted navigation speed.The integration of this technology into water ramjet engines can significantly enhance propulsion efficiency and holds substantial potential for broad applications.However,forming a gas-liquid two-phase flow within the nozzle requires introducing a large amount of rammed seawater.At this time,there is a complex phase transition problem of combustion products in the combustion chamber,which makes the thermodynamic calculation for gas-liquid two-phase water ramjet engines particularly challenging.This paper proposes a thermodynamic calculation method for gas-liquid two-phase water ramjet engines,based on the energy equation for gas-liquid two-phase flow and traditional thermodynamic principles,enabling thermodynamic calculations under conditions of ultra-high water-fuel ratios.Additionally,ground ignition tests of the gas-liquid two-phase engine were conducted,yielding critical engine test parameters.The results demonstrate that the gas-liquid two-phase water ramjet engine achieves a high specific impulse,with a theoretical maximum specific impulse of up to 7000(N s)/kg.The multiphase flow effects significantly impact engine performance,with specific impulse losses reaching up to 25.86%.The error between the thrust and specific impulse in the ground test and the theoretical values is within 10%,validating the proposed thermodynamic calculation method as a reliable reference for further research on gas-liquid two-phase water ramjet engines.展开更多
In permafrost regions of the QinghaiXizang Plateau,embankments of the Qinghai-Xizang Highway and Qinghai-Xizang Railway experiencing roadside water accumulation exhibit more pronounced engineering deteriorations.A wid...In permafrost regions of the QinghaiXizang Plateau,embankments of the Qinghai-Xizang Highway and Qinghai-Xizang Railway experiencing roadside water accumulation exhibit more pronounced engineering deteriorations.A widely accepted view is that the accumulated water adjacent to the embankment possesses substantial thermal energy,which accelerates the degradation-even disappearance-of the underlying permafrost.Moreover,the presence of roadside water keeps the embankment soil in a persistently high-moisture state,thereby making the frozen-soil embankment more susceptible to deformation under traffic loading.However,in the permafrost regions of the QinghaiXizang Plateau,deteriorations of embankments affected by roadside water are more commonly manifested as undulating pavement surfaces,and extensive crack networks appear on the embankment crest even where thermosyphons are installed.These manifestations are not fully consistent with the deterioration mechanisms proposed by existing viewpoints.We propose the hypothesis that temperature gradients,formed due to the freezing and thawing processes between the roadside wateraffected soil and the roadbed soil,lead to moisture migration under the influence of temperature gradients,resulting in frost heave and thaw settlement in the roadbed soil.To validate this hypothesis,we conducted the following investigations sequentially.Initially,we selected a roadbed with a thermosyphon(TPCT)system,which has a significant cooling effect,as the study object.By analyzing the temperature monitoring data of the roadbed section,the temperature variance was calculated to identify the time nodes where the temperature gradient of the roadbed soil was maximum and minimum.Subsequently,corresponding roadbed temperature distribution maps were drawn,illustrating the changes in the temperature and position of the lowtemperature core near the TPCT over time.Furthermore,using small-scale indoor model experiments,we qualitatively concluded that moisture in the soil migrates toward the TPCT due to the temperature gradient.Thereafter,combining borehole water content data and precipitation data from the sloped terrain construction site,the formation mechanisms and timing characteristics of roadside water accumulation were analyzed.Ultimately,by integrating the ground temperature data,air temperature data,roadside water formation mechanisms,and the operating characteristics of the TPCT,it was concluded that roadside water,while in a thawed state during TPCT operation,acts as a supplementary source for moisture migration in the roadbed soil.This migration leads to cracking in the TPCT roadbed.Therefore,this study reveals a novel damage mechanism:asynchronous freeze-thaw processes induce temperature gradients,which drive the migration of roadside water into the roadbed and are responsible for the cracking damage.展开更多
The influence of the squeeze film between the tube and the support structure on flow-induced vibrations is a critical factor in tube bundles subjected to two-phase cross-flow.This aspect can significantly alter the th...The influence of the squeeze film between the tube and the support structure on flow-induced vibrations is a critical factor in tube bundles subjected to two-phase cross-flow.This aspect can significantly alter the threshold for fluidelastic instability and affect heat transfer efficiency.This paper presents a mathematical model incorporating the squeeze film force between the tube and the support structure.We aim to clarify the mechanisms underlying fluidelastic instability in tube bundle systems exposed to two-phase flow.Using a self-developed computer program,we performed numerical calculations to examine the influence of the squeeze film on the threshold of fluidelastic instability in the tube bundle system.Furthermore,we analyzed how the thickness and length of the squeeze film affect both the underlying mechanisms and the critical velocity of fluidelastic instability.展开更多
Latent thermal energy storage(LTES)utilizing phase change material(PCM)represents an important energy-balancing technology.This paper develops a numerical model for fin-enhanced LTES and the integrated cooling system ...Latent thermal energy storage(LTES)utilizing phase change material(PCM)represents an important energy-balancing technology.This paper develops a numerical model for fin-enhanced LTES and the integrated cooling system within data center.The thermal performance of the LTES and the integrated cooling system is analyzed in terms of working conditions,structural parameters,and server load.The results indicate that the PCM does not undergo complete melting and the vapor refrigerant cannot be fully liquefied within 40 minutes,given an inlet temperature range of 287.15 to 291.15 K and a flow rate between 10 and 18 L/min.The cooling capacity decreases as the transition temperature increases from 11 to 21℃,and increases with height difference ranging from 1.9m to 3.5m.The maximum cooling capacity increases from 4529 to 5178 W as the tube length changes from 1.0 to 1.6 times,while the PCM cross-sectional area has no effects.The cooling capacity exhibits a linear increase with rising server loads.Nevertheless,the integrated cooling system can only maintain air temperatures below the specified thermal limits for durations exceeding 15 minutes when server loads remain below 3000 W.This work demonstrates the potential application of fin-enhanced LTES and its integrated cooling systems in data centers.展开更多
Cleat serves as the primary flow pathway for coalbed methane(CBM)and water.However,few studies consider the impact of local contact on two-phase flow within cleats.A visual generalized model of endogenous cleats was c...Cleat serves as the primary flow pathway for coalbed methane(CBM)and water.However,few studies consider the impact of local contact on two-phase flow within cleats.A visual generalized model of endogenous cleats was constructed based on microfluidics.A microscopic and mesoscopic observation technique was proposed to simultaneously capture gas-liquid interface morphology of pores and throat and the two-phase flow characteristics in entire cleat system.The local contact characteristics of cleats reduced absolute permeability,which resulted in a sharp increase in the starting pressure.The reduced gas flow capacity narrowed the co-infiltration area and decreased water saturation at the isotonic point in a hydrophilic environment.The increased local contact area of cleats weakened gas phase flow capacity and narrowed the co-infiltration area.Jumping events occurred in methane-water flow due to altered porosity caused by local contact in cleats.The distribution of residual phases changed the jumping direction on the micro-scale as well as the dominant channel on the mesoscale.Besides,jumping events caused additional energy dissipation,which was ignored in traditional two-phase flow models.This might contribute to the overestimation of relative permeability.The work provides new methods and insights for investigating unsaturated flow in complex porous media.展开更多
With the increasing miniaturization of systems and surging demand for power density,accurate prediction and control of two-phase flow pressure drop have become a core challenge restricting the performance of microchan...With the increasing miniaturization of systems and surging demand for power density,accurate prediction and control of two-phase flow pressure drop have become a core challenge restricting the performance of microchannel heat exchangers.Pressure drop,a critical hydraulic characteristic,serves as both a natural constraint for cooling systems and determines the power required to pump the working fluid through microchannels.This paper reviews the characteristics,prediction models,and optimization measures of two-phase flow pressure drop for low-boiling-point working fluids in microchannels.It systematically analyzes key influencing factors such as fluid physical properties,operating conditions,channel geometry,and flow patterns,and discusses the complex mechanisms of pressure drop under the coupling effect of multi-physical fields.Mainstream prediction models are reviewed:the homogeneous flow model simplifies calculations but shows large deviations at low quality;the separated flow model considers interphase interactions and can be applied to micro-scales after modification;the flow-pattern-based model performs zoned modeling but relies on subjective classification;machine learning improves prediction accuracy but faces the“black-box”problem.In terms of optimization,channel designs are improved through porous structures and micro-rib arrays,and flow rate distribution is optimized using splitters to balance pressure drop and heat transfer performance.This study provides theoretical support for microchannel thermal management in high-power-density devices.展开更多
This study investigates the feasibility of a novel dual two-phase cooling system for thermal management in lithium-ion batteries used in electric vehicles(EVs).The proposed system aims to combine low-boiling dielectri...This study investigates the feasibility of a novel dual two-phase cooling system for thermal management in lithium-ion batteries used in electric vehicles(EVs).The proposed system aims to combine low-boiling dielectric fluid immersion cooling and pulsating heat pipes(PHPs),in order to leverage the advantages of both technologies for efficient heat dissipation in a completely passive configuration.Experimental evaluations conducted under different discharge conditions demonstrate that the systemeffectivelymaintains battery temperatureswithin the optimal range of 20–40℃,with enhanced temperature uniformity and stability.While the PHP exhibited minimal impact at low power,its role became critical under higher discharge rates,ensuring efficient vapor condensation and pressure stability.The results highlight the potential of this passive cooling system to improve battery performance and safety,supporting its application in EV battery thermal management.Future work aims to optimize design parameters and evaluate real battery modules under ultra-fast charging scenarios.展开更多
Thin film lubrication (TFL) is a condition in which the lubricating features between two surfaces in relative motion are determined by the combination of the properties of the surfaces and the lubricant and viscosity ...Thin film lubrication (TFL) is a condition in which the lubricating features between two surfaces in relative motion are determined by the combination of the properties of the surfaces and the lubricant and viscosity of the lubricant. The effects imposed by couple stress on lubrication characteristics cannot be disregarded in this regime where the ordered molecules dominate the fluid field. There are different tensor measures and constitutive equations in this case other than Newtonian case. The lubrication of two-phase (solid phase and liquid phase) fluid is investigated in this paper. The existence of couple stress will enhance the lubricant viscosity and hence increase the film thickness and improve the load-carrying capability. Size-dependent effects can be seen in the lubrication with couple stress, and the thinner the lubricating film is, the more obvious the effect will be.展开更多
The flow field of gas and liquid in a φ150mm rotating-stream-tray (RST) scrubber is simulated by using computational fluid dynamic (CFD) method. The sismulation is based on the two-equation RNG κ-ε turbulence model...The flow field of gas and liquid in a φ150mm rotating-stream-tray (RST) scrubber is simulated by using computational fluid dynamic (CFD) method. The sismulation is based on the two-equation RNG κ-ε turbulence model, Eulerian multiphase model, and a real-shape 3D model with a huge number of meshes. The simulation results include detailed information about velocity, pressure, volume fraction and so on. Some features of the flow field are obtained: liquid is atomized in a thin annular zone; a high velocity air zone prevents water drops at the bottom from flying towards the wall; the pressure varies sharply at the end of blades and so on. The results will be helpful for structure optimization and engineering design.展开更多
Characterizing the complex two-phase hydrodynamics in structured packed columns requires a power- ful modeling tool. The traditional two-dimensional model exhibits limitations when one attempts to model the de- tailed...Characterizing the complex two-phase hydrodynamics in structured packed columns requires a power- ful modeling tool. The traditional two-dimensional model exhibits limitations when one attempts to model the de- tailed two-phase flow inside the columns. The present paper presents a three-dimensional computational fluid dy- namics （CFD） model to simulate the two-phase flow in a representative unit of the column. The unit consists of an CFD calculations on column packed with Flexipak 1Y were implemented within the volume of fluid （VOF） mathe- matical framework. The CFD model was validated by comparing the calculated thickness of liquid film with the available experimental data. Special attention was given to quantitative analysis of the effects of gravity on the hy- drodynamics. Fluctuations in the liquid mass flow rate and the calculated pressure drop loss were found to be quali- tatively in agreement with the experimental observations.展开更多
This work investigated the dynamic behavior of vertical pipes conveying gas-liquid two-phase flow when subjected to external excitations at both ends.Even with minimal excitation amplitude,resonance can occur when the...This work investigated the dynamic behavior of vertical pipes conveying gas-liquid two-phase flow when subjected to external excitations at both ends.Even with minimal excitation amplitude,resonance can occur when the excitation frequency aligns with the natural frequency of the pipe,significantly increasing the degree of operational risk.The governing equation of motion based on the Euler-Bernoulli beam is derived for the relative deflection with stationary simply supported ends,with the effects of the external excitations represented by source terms distributed along the pipe length.The fourth-order partial differential equation is solved via the generalized integral transform technique(GITT),with the solution successfully verified via comparison with results in the literature.A comprehensive analysis of the vibration phenomena and changes in the motion state of the pipe is conducted for three classes of external excitation conditions:same frequency and amplitude(SFSA),same frequency but different amplitudes(SFDA),and different frequencies and amplitudes(DFDA).The numerical results show that with increasing gas volume fraction,the position corresponding to the maximum vibration displacement shifts upward.Compared with conditions without external excitation,the vibration displacement of the pipe conveying two-phase flow under external excitation increases significantly.The frequency of external excitation has a significant effect on the dynamic behavior of a pipe conveying two-phase flow.展开更多
RH vacuum degasser is a very important secondary refining device in the production of high quality steels. The flow field of molten steel in RH system plays a significant role in determining productivity of the equipm...RH vacuum degasser is a very important secondary refining device in the production of high quality steels. The flow field of molten steel in RH system plays a significant role in determining productivity of the equipment. The homogeneous model and VOF method were often used to predict the flow field in RH system, but these kinds of models simplified the interaction between gas bubbles and molten steel. In the present work, a numerical model of a whole RH system, including vacuum degasser, immersed legs and ladle,was built based on gas-liquid two-fluid model, and it could be used to analyze the interaction between argon bubbles and molten steel, to understand the effect of the bubble size to the flow field.展开更多
Numerical simulations of evolution characteristics of slug flow across a 90°pipe bend have been carried out to study the fluid−structure interaction response induced by internal slug flow.The two-phase flow patte...Numerical simulations of evolution characteristics of slug flow across a 90°pipe bend have been carried out to study the fluid−structure interaction response induced by internal slug flow.The two-phase flow patterns and turbulence were modelled by using the volume of fluid(VOF)model and the Realizable k−εturbulence model respectively.Firstly,validation of the CFD model was carried out and the desirable results were obtained.The different flow patterns and the time-average mean void fraction was coincident with the reported experimental data.Simulations of different cases of slug flow have been carried out to show the effects of superficial gas and liquid velocity on the evolution characteristics of slug flow.Then,a one-way coupled fluid-structure interaction framework was established to investigate the slug flow interaction with a 90°pipe bend under various superficial liquid and gas velocities.It was found that the maximum total deformation and equivalent stress increased with the increasing superficial gas velocity,while decreased with the increasing superficial liquid velocity.In addition,the total deformation and equivalent stress has obvious periodic fluctuation.Furthermore,the distribution position of maximum deformation and stress was related to the evolution of slug flow.With the increasing superficial gas velocity,the maximum total deformation was mainly located at the 90°pipe bend.But as the superficial liquid velocity increases,the maximum total deformation was mainly located in the horizontal pipe section.Consequently,the slug flow with higher superficial gas velocity will induce more serious cyclical impact on the 90°pipe bend.展开更多
基金National Science Foundation of China,Grant/Award Number:5227090113Shenzhen Science and Technology Program,Grant/Award Numbers:KCXFZ20230731093901003,KCXFZ20211020163816023The Project of Hetao Shenzhen-Hong Kong Science and Technology Innovation Cooperation Zone,Grant/Award Number:HZQB-KCZYB-2020083。
文摘The two-phase flow in porous media is affected by multiple factors.In the present study,a two-dimensional numerical model of porous media was developed using the actual pore structure of the core sample.The phase field method was utilized to simulate the impact of displacement velocity,the water-gas viscosity ratio,and the density ratio on the flow behavior of two-phase fluids in porous media.The effectiveness of displacement was evaluated by analyzing CO_(2)saturation levels.The results indicate that the saturation of CO_(2)in porous media increased as the displacement velocity increased.When the displacement velocity exceeded 0.01 m/s,there was a corresponding increase in CO_(2)saturation.Conversely,when the displacement velocity was below this threshold,the impact on CO_(2)saturation was minimal.An“inflection point,”M3,was present in the viscosity ratio.When the viscosity of CO_(2)is less than 8.937×10^(-5)Pa·s(viscosity ratio below M3),variations in the viscosity of CO_(2)had little impact on its saturation.Conversely,when the viscosity of CO_(2)exceeded 8.937×10^(-5)Pa·s(viscosity ratio greater than M3),saturation increased with an increase in the viscosity ratio.In terms of the density ratio,the saturation of CO_(2)increased monotonically with an increase in the density ratio.Similarly,increasing density ratios resulted in a monotonic increase in CO_(2)saturation,though this trend was less pronounced in numerical simulations.Analysis results of displacement within dead-end pores using pressure and velocity diagrams reveal eddy currents as contributing factors.Finally,the impact of pore throat structure on the formation of dominant channels was examined.
文摘A mathematical model of two-phase fluid nonlinear flow in the direction of normal of ellipse through low-permeability porous media was established according to a nonlinear flow law expressed in a continuous function with three parameters, a mass conservation law and a concept of turbulent ellipses. A solution to the model was obtained by using a finite difference method and an extrapolation method. Formulas of calculating development index not only before but also after water breaks through an oil well in the condition of two-phase fluid nonlinear flow in the media were derived. An example was discussed. Water saturation distribution was presented. The moving law of drainage front was found. Laws of change of pressure difference with time were recognized. Results show that there is much difference of water saturation distribution between nonlinear flow and linear flow; that drainage front by water moves faster, water breaks through sooner and the index gets worse because of the nonlinear flow; and that dimensionless pressure difference gets larger at the same dimensionless time and difficulty of oil development becomes bigger by the nonlinear flow. Thus, it is necessary that influence of nonlinear flow on development indexes of the oil fields be taken into account. The results provide water-flooding development of the oilfields with scientific basis.
文摘Climate change is a reality. The burning of fossil fuels from oil, natural gas and coal is responsible for much of the pollution and the increase in the planet’s average temperature, which has raised discussions on the subject, given the emergencies related to climate. An energy transition to clean and renewable sources is necessary and urgent, but it will not be quick. In this sense, increasing the efficiency of oil extraction from existing sources is crucial, to avoid waste and the drilling of new wells. The purpose of this work was to add diffusive and dispersive terms to the Buckley-Leverett equation in order to incorporate extra phenomena in the temporal evolution between the water-oil and oil-water transitions in the pipeline. For this, the modified Buckley-Leverett equation was discretized via essentially weighted non-oscillatory schemes, coupled with a three-stage Runge-Kutta and a fourth-order centered finite difference methods. Then, computational simulations were performed and the results showed that new features emerge in the transitions, when compared to classical simulations. For instance, the dispersive term inhibits the diffusive term, adding oscillations, which indicates that the absorption of the fluid by the porous medium occurs in a non-homogeneous manner. Therefore, based on research such as this, decisions can be made regarding the replacement of the porous medium or the insertion of new components to delay the replacement.
基金supported by the National Natural Science Foundation of China (No.51041007)the Tribology Science Fund of State Key Laboratory of Tribology (No.SKLTKF10B07)
文摘The corrosion behavior of type 1045（AISI） carbon steel（CS） in oil-water fluids was investigated by considering the surface wetting state as the breakthrough point.The surface water wetting percentage（SWWP）and corrosion weight loss of CS in different oil-water fluids were measured.The morphology and composition of the corrosion films were detected via scanning electron microscopy,electron-probe facescanning technology and Fourier-transform infrared spectroscopy.The results indicated that the corrosion weight loss of CS in the oil-water fluids corresponded with SWWP and that the corrosion process was influenced by the participation of oil.
文摘Equations of motion for bubble collapse in solid-liquid two-phase fluid have been derived, in which the resistance coupling effects between the liquid and solid particles have been considered. The motion of particles during the bubble collapse and the effects of particles on bubble collapse have been calculated and discussed. Qualitative relations between the concentration and the size of the particles and the rate of bubble collapse have been obtaind.
基金supported by the National Science Centre(Grant No.UMO-2013/09/B/ST8/02054)
文摘Research interests have recently been directed towards electrical discharges in multi-phase environments.Natural electrical discharges,such as lightning and coronas,occur in the Earth＇s atmosphere,which is actually a mixture of gaseous phase（air） and suspended solid and liquid particulate matters（PMs）.An example of an anthropogenic gaseous multi-phase environment is the flow of flue gas through electrostatic precipitators（ESPs）,which are generally regarded as a mixture of a post-combustion gas with solid PM and microdroplets suspended in it.Electrical discharges in multi-phase environments,the knowledge of which is scarce,are becoming an attractive research subject,offering a wide variety of possible discharges and multi-phase environments to be studied.This paper is an introduction to electrical discharges in multi-phase environments.It is focused on DC negative coronas and accompanying electrohydrodynamic（EHD） flows in a gaseous two-phase fluid formed by air（a gaseous phase） and solid PM（a solid phase）,run under laboratory conditions.The introduction is based on a review of the relevant literature.Two cases will be considered：the first case is of a gaseous two-phase fluid,initially motionless in a closed chamber before being subjected to a negative corona（with the needle-toplate electrode arrangement）,which afterwards induces an EHD flow in the chamber,and the second,of a gaseous two-phase fluid flowing transversely with respect to the needle-to-plate electrode axis along a chamber with a corona discharge running between the electrodes.This review-based introductory paper should be of interest to theoretical researchers and modellers in the field of negative corona discharges in single-or two-phase fluids,and for engineers who work on designing EHD devices（such as ESPs,EHD pumps,and smoke detectors）.
基金financially supported by the National Key R&D Program of China(2016YFC0600104)the Strategic Priority Research Program(B)of the Chinese Academy of Sciences(XDB 18010401)+1 种基金the National Natural Science Foundation of China(41902043)the Science and Technology Foundation Project in Guizhou Province([2019]1316,[2020]1Z032)。
文摘This paper introduces a 100 MPa water gas twophase fluid pressurization device.The device can provide 100 MPa gas pressure and 200 MPa liquid pressure for small volume(<20 mL)high-pressure experimental devices.This device can make the pressure control independent of the temperature control without changing the material components of the system.The resolution of this device in adjusting the pressure is±0.2 MPa in the process of boosting and depressurizing.This pressure boosting device generates very little vibration during work and it can be used in experiments with strict requirements on vibration.As a thermodynamic parameter,pressure has a great influence on matter.In the field of experimental geochemistry,pressure is not only an experimental method and an extreme condition but an important physical parameter independent of temperature and chemical composition.
基金supported by the Stable Support Fund forBasic Disciplines,China(No.3072024WD0201)。
文摘Underwater gas-liquid two-phase propulsion technology is an emerging propulsion method that offers high efficiency and unrestricted navigation speed.The integration of this technology into water ramjet engines can significantly enhance propulsion efficiency and holds substantial potential for broad applications.However,forming a gas-liquid two-phase flow within the nozzle requires introducing a large amount of rammed seawater.At this time,there is a complex phase transition problem of combustion products in the combustion chamber,which makes the thermodynamic calculation for gas-liquid two-phase water ramjet engines particularly challenging.This paper proposes a thermodynamic calculation method for gas-liquid two-phase water ramjet engines,based on the energy equation for gas-liquid two-phase flow and traditional thermodynamic principles,enabling thermodynamic calculations under conditions of ultra-high water-fuel ratios.Additionally,ground ignition tests of the gas-liquid two-phase engine were conducted,yielding critical engine test parameters.The results demonstrate that the gas-liquid two-phase water ramjet engine achieves a high specific impulse,with a theoretical maximum specific impulse of up to 7000(N s)/kg.The multiphase flow effects significantly impact engine performance,with specific impulse losses reaching up to 25.86%.The error between the thrust and specific impulse in the ground test and the theoretical values is within 10%,validating the proposed thermodynamic calculation method as a reliable reference for further research on gas-liquid two-phase water ramjet engines.
基金supported by the Major Science and Technology Project of Gansu Province(Grant No.24ZD13FA003 and 23ZDWA005)National Natural Science Foundation of China(Grant No.42371140,42301163,41971087 and 42272332)the program of the State Key Laboratory of Cryospheric Science and Frozen Soil Engineering,CAS(No.CSFSEZZ-2411)。
文摘In permafrost regions of the QinghaiXizang Plateau,embankments of the Qinghai-Xizang Highway and Qinghai-Xizang Railway experiencing roadside water accumulation exhibit more pronounced engineering deteriorations.A widely accepted view is that the accumulated water adjacent to the embankment possesses substantial thermal energy,which accelerates the degradation-even disappearance-of the underlying permafrost.Moreover,the presence of roadside water keeps the embankment soil in a persistently high-moisture state,thereby making the frozen-soil embankment more susceptible to deformation under traffic loading.However,in the permafrost regions of the QinghaiXizang Plateau,deteriorations of embankments affected by roadside water are more commonly manifested as undulating pavement surfaces,and extensive crack networks appear on the embankment crest even where thermosyphons are installed.These manifestations are not fully consistent with the deterioration mechanisms proposed by existing viewpoints.We propose the hypothesis that temperature gradients,formed due to the freezing and thawing processes between the roadside wateraffected soil and the roadbed soil,lead to moisture migration under the influence of temperature gradients,resulting in frost heave and thaw settlement in the roadbed soil.To validate this hypothesis,we conducted the following investigations sequentially.Initially,we selected a roadbed with a thermosyphon(TPCT)system,which has a significant cooling effect,as the study object.By analyzing the temperature monitoring data of the roadbed section,the temperature variance was calculated to identify the time nodes where the temperature gradient of the roadbed soil was maximum and minimum.Subsequently,corresponding roadbed temperature distribution maps were drawn,illustrating the changes in the temperature and position of the lowtemperature core near the TPCT over time.Furthermore,using small-scale indoor model experiments,we qualitatively concluded that moisture in the soil migrates toward the TPCT due to the temperature gradient.Thereafter,combining borehole water content data and precipitation data from the sloped terrain construction site,the formation mechanisms and timing characteristics of roadside water accumulation were analyzed.Ultimately,by integrating the ground temperature data,air temperature data,roadside water formation mechanisms,and the operating characteristics of the TPCT,it was concluded that roadside water,while in a thawed state during TPCT operation,acts as a supplementary source for moisture migration in the roadbed soil.This migration leads to cracking in the TPCT roadbed.Therefore,this study reveals a novel damage mechanism:asynchronous freeze-thaw processes induce temperature gradients,which drive the migration of roadside water into the roadbed and are responsible for the cracking damage.
基金financially supported by the National Natural Science Foundation of China(Grant No.12072336).
文摘The influence of the squeeze film between the tube and the support structure on flow-induced vibrations is a critical factor in tube bundles subjected to two-phase cross-flow.This aspect can significantly alter the threshold for fluidelastic instability and affect heat transfer efficiency.This paper presents a mathematical model incorporating the squeeze film force between the tube and the support structure.We aim to clarify the mechanisms underlying fluidelastic instability in tube bundle systems exposed to two-phase flow.Using a self-developed computer program,we performed numerical calculations to examine the influence of the squeeze film on the threshold of fluidelastic instability in the tube bundle system.Furthermore,we analyzed how the thickness and length of the squeeze film affect both the underlying mechanisms and the critical velocity of fluidelastic instability.
基金supported by the National Natural Science Found of China(No.52178073).
文摘Latent thermal energy storage(LTES)utilizing phase change material(PCM)represents an important energy-balancing technology.This paper develops a numerical model for fin-enhanced LTES and the integrated cooling system within data center.The thermal performance of the LTES and the integrated cooling system is analyzed in terms of working conditions,structural parameters,and server load.The results indicate that the PCM does not undergo complete melting and the vapor refrigerant cannot be fully liquefied within 40 minutes,given an inlet temperature range of 287.15 to 291.15 K and a flow rate between 10 and 18 L/min.The cooling capacity decreases as the transition temperature increases from 11 to 21℃,and increases with height difference ranging from 1.9m to 3.5m.The maximum cooling capacity increases from 4529 to 5178 W as the tube length changes from 1.0 to 1.6 times,while the PCM cross-sectional area has no effects.The cooling capacity exhibits a linear increase with rising server loads.Nevertheless,the integrated cooling system can only maintain air temperatures below the specified thermal limits for durations exceeding 15 minutes when server loads remain below 3000 W.This work demonstrates the potential application of fin-enhanced LTES and its integrated cooling systems in data centers.
基金the financial support from the National Natural Science Foundation of China (No.42102127)the Postdoctoral Research Foundation of China (No.2024 M751860)。
文摘Cleat serves as the primary flow pathway for coalbed methane(CBM)and water.However,few studies consider the impact of local contact on two-phase flow within cleats.A visual generalized model of endogenous cleats was constructed based on microfluidics.A microscopic and mesoscopic observation technique was proposed to simultaneously capture gas-liquid interface morphology of pores and throat and the two-phase flow characteristics in entire cleat system.The local contact characteristics of cleats reduced absolute permeability,which resulted in a sharp increase in the starting pressure.The reduced gas flow capacity narrowed the co-infiltration area and decreased water saturation at the isotonic point in a hydrophilic environment.The increased local contact area of cleats weakened gas phase flow capacity and narrowed the co-infiltration area.Jumping events occurred in methane-water flow due to altered porosity caused by local contact in cleats.The distribution of residual phases changed the jumping direction on the micro-scale as well as the dominant channel on the mesoscale.Besides,jumping events caused additional energy dissipation,which was ignored in traditional two-phase flow models.This might contribute to the overestimation of relative permeability.The work provides new methods and insights for investigating unsaturated flow in complex porous media.
基金supported by the Beijing Municipal Science&Technology Commission(Z231100006123010).
文摘With the increasing miniaturization of systems and surging demand for power density,accurate prediction and control of two-phase flow pressure drop have become a core challenge restricting the performance of microchannel heat exchangers.Pressure drop,a critical hydraulic characteristic,serves as both a natural constraint for cooling systems and determines the power required to pump the working fluid through microchannels.This paper reviews the characteristics,prediction models,and optimization measures of two-phase flow pressure drop for low-boiling-point working fluids in microchannels.It systematically analyzes key influencing factors such as fluid physical properties,operating conditions,channel geometry,and flow patterns,and discusses the complex mechanisms of pressure drop under the coupling effect of multi-physical fields.Mainstream prediction models are reviewed:the homogeneous flow model simplifies calculations but shows large deviations at low quality;the separated flow model considers interphase interactions and can be applied to micro-scales after modification;the flow-pattern-based model performs zoned modeling but relies on subjective classification;machine learning improves prediction accuracy but faces the“black-box”problem.In terms of optimization,channel designs are improved through porous structures and micro-rib arrays,and flow rate distribution is optimized using splitters to balance pressure drop and heat transfer performance.This study provides theoretical support for microchannel thermal management in high-power-density devices.
基金National Recovery and Resilience Plan(NRRP)Mission 4 Component 2 Investment 1.5-Call for tender No.3277 of 30/12/2021 of Italian Ministry of University and Research funded by the European Union-NextGenerationEU(Award Number:Project code ECS00000033,Concession Decree No.1052 of 23 June 2022 adopted by the Italian Ministry of,CUP D93C22000460001,“Ecosystem for Sustainable Transition in Emilia-Romagna”(Ecosister)).
文摘This study investigates the feasibility of a novel dual two-phase cooling system for thermal management in lithium-ion batteries used in electric vehicles(EVs).The proposed system aims to combine low-boiling dielectric fluid immersion cooling and pulsating heat pipes(PHPs),in order to leverage the advantages of both technologies for efficient heat dissipation in a completely passive configuration.Experimental evaluations conducted under different discharge conditions demonstrate that the systemeffectivelymaintains battery temperatureswithin the optimal range of 20–40℃,with enhanced temperature uniformity and stability.While the PHP exhibited minimal impact at low power,its role became critical under higher discharge rates,ensuring efficient vapor condensation and pressure stability.The results highlight the potential of this passive cooling system to improve battery performance and safety,supporting its application in EV battery thermal management.Future work aims to optimize design parameters and evaluate real battery modules under ultra-fast charging scenarios.
基金Nomenclature: τ, stress tensor ρ, density+7 种基金 a, acceleration (m/s2)f, body force (N)p, pressure (Pa) λ, second viscosity coefficient d, strain tensor δ, sign function η, material constant responsible for couple stress parameter μ dynamic visc
文摘Thin film lubrication (TFL) is a condition in which the lubricating features between two surfaces in relative motion are determined by the combination of the properties of the surfaces and the lubricant and viscosity of the lubricant. The effects imposed by couple stress on lubrication characteristics cannot be disregarded in this regime where the ordered molecules dominate the fluid field. There are different tensor measures and constitutive equations in this case other than Newtonian case. The lubrication of two-phase (solid phase and liquid phase) fluid is investigated in this paper. The existence of couple stress will enhance the lubricant viscosity and hence increase the film thickness and improve the load-carrying capability. Size-dependent effects can be seen in the lubrication with couple stress, and the thinner the lubricating film is, the more obvious the effect will be.
基金Supported by the National 863 Project (2001AA642030-1) and Zhejiang Provincial Key Research Project (010007037).
文摘The flow field of gas and liquid in a φ150mm rotating-stream-tray (RST) scrubber is simulated by using computational fluid dynamic (CFD) method. The sismulation is based on the two-equation RNG κ-ε turbulence model, Eulerian multiphase model, and a real-shape 3D model with a huge number of meshes. The simulation results include detailed information about velocity, pressure, volume fraction and so on. Some features of the flow field are obtained: liquid is atomized in a thin annular zone; a high velocity air zone prevents water drops at the bottom from flying towards the wall; the pressure varies sharply at the end of blades and so on. The results will be helpful for structure optimization and engineering design.
基金Supported by the Major State Basic Research Development Program of China(2011CB706501)the National Natural Science Foundation of China(51276157)
文摘Characterizing the complex two-phase hydrodynamics in structured packed columns requires a power- ful modeling tool. The traditional two-dimensional model exhibits limitations when one attempts to model the de- tailed two-phase flow inside the columns. The present paper presents a three-dimensional computational fluid dy- namics （CFD） model to simulate the two-phase flow in a representative unit of the column. The unit consists of an CFD calculations on column packed with Flexipak 1Y were implemented within the volume of fluid （VOF） mathe- matical framework. The CFD model was validated by comparing the calculated thickness of liquid film with the available experimental data. Special attention was given to quantitative analysis of the effects of gravity on the hy- drodynamics. Fluctuations in the liquid mass flow rate and the calculated pressure drop loss were found to be quali- tatively in agreement with the experimental observations.
基金financially supported by the Key Research and Development Program of Shandong Province(Grant Nos.2022CXGC020405,2023CXGC010415 and 2025TSGCCZZB0238)the National Natural Science Foundation of China(Grant No.52171288)the financial support from CNPq,FAPERJ,ANP,Embrapii,and China National Petroleum Corporation(CNPC).
文摘This work investigated the dynamic behavior of vertical pipes conveying gas-liquid two-phase flow when subjected to external excitations at both ends.Even with minimal excitation amplitude,resonance can occur when the excitation frequency aligns with the natural frequency of the pipe,significantly increasing the degree of operational risk.The governing equation of motion based on the Euler-Bernoulli beam is derived for the relative deflection with stationary simply supported ends,with the effects of the external excitations represented by source terms distributed along the pipe length.The fourth-order partial differential equation is solved via the generalized integral transform technique(GITT),with the solution successfully verified via comparison with results in the literature.A comprehensive analysis of the vibration phenomena and changes in the motion state of the pipe is conducted for three classes of external excitation conditions:same frequency and amplitude(SFSA),same frequency but different amplitudes(SFDA),and different frequencies and amplitudes(DFDA).The numerical results show that with increasing gas volume fraction,the position corresponding to the maximum vibration displacement shifts upward.Compared with conditions without external excitation,the vibration displacement of the pipe conveying two-phase flow under external excitation increases significantly.The frequency of external excitation has a significant effect on the dynamic behavior of a pipe conveying two-phase flow.
文摘RH vacuum degasser is a very important secondary refining device in the production of high quality steels. The flow field of molten steel in RH system plays a significant role in determining productivity of the equipment. The homogeneous model and VOF method were often used to predict the flow field in RH system, but these kinds of models simplified the interaction between gas bubbles and molten steel. In the present work, a numerical model of a whole RH system, including vacuum degasser, immersed legs and ladle,was built based on gas-liquid two-fluid model, and it could be used to analyze the interaction between argon bubbles and molten steel, to understand the effect of the bubble size to the flow field.
基金sponsored by the National Natural Science Foundation of China(Grant No.51779143)the Oceanic Interdisciplinary Program of Shanghai Jiao Tong University(Grant No.SL2020ZD101)the Cultivation of Scientific Research Ability of Young Talents of Shanghai Jiao Tong University(Grant No.19X100040072).
文摘Numerical simulations of evolution characteristics of slug flow across a 90°pipe bend have been carried out to study the fluid−structure interaction response induced by internal slug flow.The two-phase flow patterns and turbulence were modelled by using the volume of fluid(VOF)model and the Realizable k−εturbulence model respectively.Firstly,validation of the CFD model was carried out and the desirable results were obtained.The different flow patterns and the time-average mean void fraction was coincident with the reported experimental data.Simulations of different cases of slug flow have been carried out to show the effects of superficial gas and liquid velocity on the evolution characteristics of slug flow.Then,a one-way coupled fluid-structure interaction framework was established to investigate the slug flow interaction with a 90°pipe bend under various superficial liquid and gas velocities.It was found that the maximum total deformation and equivalent stress increased with the increasing superficial gas velocity,while decreased with the increasing superficial liquid velocity.In addition,the total deformation and equivalent stress has obvious periodic fluctuation.Furthermore,the distribution position of maximum deformation and stress was related to the evolution of slug flow.With the increasing superficial gas velocity,the maximum total deformation was mainly located at the 90°pipe bend.But as the superficial liquid velocity increases,the maximum total deformation was mainly located in the horizontal pipe section.Consequently,the slug flow with higher superficial gas velocity will induce more serious cyclical impact on the 90°pipe bend.
