An acidic mixture of sulfuric and fluosilicic acid(H_(2)SO_(4)+H_(2)SiF_(6))was employed as lixiviant to enhance leaching of lithium from lepidolite.The H_(2)SiF_(6) was obtained as a byproduct of anhydrous hydrofluor...An acidic mixture of sulfuric and fluosilicic acid(H_(2)SO_(4)+H_(2)SiF_(6))was employed as lixiviant to enhance leaching of lithium from lepidolite.The H_(2)SiF_(6) was obtained as a byproduct of anhydrous hydrofluoric acid production,aiming to provide HF molecules.It was found that the HF molecules were the main reaction component and played a key role in strengthening the dissolution of lepidolite.Different factors,including mass ratio of ore/H_(2)SO_(4)/H_(2)SiF_(6),concentrations of H_(2)SO_(4) and H_(2)SiF_(6),leaching temperatures(40−80℃)and time(15−75 min),were investigated.Moreover,an efficient tubular reactor was employed to improve this acid leaching system.Under the optimal conditions(ore/H_(2)SO_(4)/H_(2)SiF_(6) mass ratio of 1:0.8:1.6,80 wt.% H_(2)SO_(4),15 wt.% H_(2)SiF_(6),80℃,15 min),97.9% of Li,96.4% of K,97.6% of Rb,96.7% of Cs and 81.4% of Al(mass fraction)were leached.Additionally,a two-step thermal process was proposed to remove fluorine of leaching slurry.This acid treatment using an acidic mixture of H_(2)SO_(4) and H_(2)SiF_(6) in a continuous tubular reactor shows potential as an alternative process to extract lithium from lepidolite.展开更多
Production of biodiesel with supercritical methanol is a green synthesis process.A study was carried out in a vertical tubular reactor with a length of 3700 mm and a diameter of 20 mm at 275-375°C,15 MPa,and mola...Production of biodiesel with supercritical methanol is a green synthesis process.A study was carried out in a vertical tubular reactor with a length of 3700 mm and a diameter of 20 mm at 275-375°C,15 MPa,and molar ratio of methanol to soybean oil of 40︰1.The phase holdup,intermediate product,yield and axial distribution of methyl ester(ME) were investigated.Methanol and oil were mixed non-uniformly due to the formation of biodiesel and difference in their densities,even when the reaction system was in the supercritical state.From top to bottom,the phase holdup of methanol increased and that of oil decreased.As temperature increased,the concentrations of monoglyceride and diglyceride decreased gradually and the ME yield increased.When the temperature reached 300°C,the critical temperature of the system,the ME yield was 50%.Further increase in temperature led to a sharp in-crease of ME yield.However,at 375°C after 1200 s of reaction time,the decomposition rate of ME was greater than its formation rate,reducing the ME yield.展开更多
Ethane steam cracking process in an industrial reactor was investigated.An one-demsional(1D)steady-state model was developed firstly by using an improved molecular reaction scheme and was then simulated in Aspen Plus....Ethane steam cracking process in an industrial reactor was investigated.An one-demsional(1D)steady-state model was developed firstly by using an improved molecular reaction scheme and was then simulated in Aspen Plus.A comparison of model results with industrial data and previously reported results showed that the model can predict the process kinetics more accurately.In addition,the validated model was used to study the effects of different process variables,including coil outlet temperature(COT),steam-to-ethane ratio and residence time on ethane conversion,ethylene selectivity,products yields,and coking rate.Finally,steady-state optimization was conducted to the operation of industrial reactor.The COT and steam-to-ethane ratio were taken as decision variables to maximize the annual operational profit.展开更多
With the help of the ceramic foam research efforts and preparation techniques, the ZrO2 polycrystalline ceramic foam catalyst was synthesized, and its characteristics, including the crystal structure, the phase compos...With the help of the ceramic foam research efforts and preparation techniques, the ZrO2 polycrystalline ceramic foam catalyst was synthesized, and its characteristics, including the crystal structure, the phase composition, the acid–base properties, and the microstructure, were analyzed by XRD, SEM, Py-IR, and BET techniques. The performance of the ZrO2 polycrystalline ceramic foam catalyst in a tubular reactor was investigated via biodiesel synthesis using S. wilsoniana oil and methanol. The effects of reaction conditions(i.e., reaction temperature, reaction pressure, and volume ratio of methanol to S. wilsoniana oil) on transesterification efficiency were investigated, and the reaction conditions were optimized using RSM. The optimum reaction temperature, reaction pressure, and volume ratio of methanol to S. wilsoniana oil were determined to be 290 ℃, 10 MPa, and 4:1, respectively. Under this condition, the FAME content in the product oil reached 98.38%. The performance of the ZrO2 polycrystalline ceramic foam catalyst synthesized in this work for biodiesel synthesis from S. wilsoniana oil with a moisture content of 7.1% and an acid value of 130.697 mg KOH/g was examined, and the FAME content in the product oil was found to be 93% and 97.67%, respectively. The FAME content in the product oil exceeded 97% after five consecutive cycles(12 h per cycle of use) of the catalyst. The proposed catalyst represents a new type of solid catalyst with excellent acid resistance, water resistance, esterification efficiency, and catalytic stability.展开更多
In this study, rheological examination of the mixture of a tubular reactor in which methyl methacrylate was polymerized has been studied. The n(flow behavior index) value of Power Law Model of mixture contained in the...In this study, rheological examination of the mixture of a tubular reactor in which methyl methacrylate was polymerized has been studied. The n(flow behavior index) value of Power Law Model of mixture contained in the reactor has been determined within the span of 0.3492 to 0.9889 by curve fitting. Employing these numerical data for velocity profile, the reactor has been modeled. Moreover, the functions of the reactor have been compared in the three modes of plug, mixed and laminar flow. The results obtained in this research indicate that the polymethyl methacrylate mixture contained in the reactor is pseudo-plastic. Moreover, as the conversion grows, the velocity profile starts as a parabolic profile and approaches the plug mode; although it never reaches the plug. The other conclusions borne in this study indicate that when the reactor's radius is decreased, the conversion rate grows. However, as decreasing the radius would also reduce the productions rate, this procedure is not economical. Finally, in this modeling, the amount of conversion is equal to 56.47% at the end and according to its laboratory proportion which is 55.88%, it has reached the conclusion that the modeling duly undertaken is applicable and valid.展开更多
Ethylene glycol monoethyl ether acetate (EGEA), an excellent solvent, is prepared with ethylene oxide (EO) and ethyl acetate (EA) in a tubular reactor under suitable reaction condition. The single circulation yield ca...Ethylene glycol monoethyl ether acetate (EGEA), an excellent solvent, is prepared with ethylene oxide (EO) and ethyl acetate (EA) in a tubular reactor under suitable reaction condition. The single circulation yield can reach 81%. This technology is not only safe but also makes it possible to continuously produce EGEA in industry,with low content of high boiling point by-products.展开更多
In this study, we present a model whereby the centre of the atomization channel is shown to be the optimal location for the spectrometric data acquisition in a quartz cell atomizer. The study aims to explore the hydri...In this study, we present a model whereby the centre of the atomization channel is shown to be the optimal location for the spectrometric data acquisition in a quartz cell atomizer. The study aims to explore the hydride generation technique which is normally coupled with efficient thermal source to apply determination of heavy metals in water samples via spectrometric analysis. The arsenic hydride generation process and the atomization of the generated hydride in a quartz cell atomizer were studied analytically as model case studies. The hydride generation (HG) process was analyzed by adopting two hypotheses, the nascent hydrogen and formation of intermediate hydroboron species, where the results based on the second hypothesis are found to be more realistic for design purposes. Moreover, the release of the generated hydride from the liquid phase and their transport to the gas phase is simulated in a helical tubular section, in which the actual tubular section length required for separation is deduced. The analytical results have been verified experimentally by measuring the signal intensity for the free arsenic atoms against several reaction tube lengths, in which increasing the tubular section length from 12 cm to 100 cm results in signal amelioration by no more than 6.6%. Furthermore, the atomization of the hydride and the distribution of the generated free atoms are deduced in two configurations of tubular quartz atomizers. The results obtained from both studied cases illustrate that a high concentration of the free analyte atoms is generated in the first part of the atomization channel, saturates to a maximum in a position at the atomizer centre, and dissipates at the inside wall of the tubular atomizer before reaching the atomizer outlet edge, which is found to be in total agreement with the current understanding of atomization mechanism in tubular atomizer and emphasizes the fact that the centre of the quartz cell atomizer is the best location for the spectrometric data acquisition.展开更多
This paper presents the results of polymeric deposit analysis in HP recycling system on two ethylene polymerization trains in tubular reactors when using mixed initiation (organic peroxides and oxygen) in the process ...This paper presents the results of polymeric deposit analysis in HP recycling system on two ethylene polymerization trains in tubular reactors when using mixed initiation (organic peroxides and oxygen) in the process of various grade production. It is demonstrated that polymers belong to the very low density type (with ρ in 0,860 to 0,900 g/cm3 range), due to ultra high branching. Consideration is given to known processes of that kind polymer production. There discussed the alternatives of different approaches to special process features found. It is stated that 80-year high pressure PE synthesis history has been keeping potential for the development.展开更多
A gas-tight BaCo 0.7 Fe 0.2 Nb 0.1 O 3-δ（BCFNO） tubular membrane was fabricated by hot pressure casting.And a membrane reactor with BCFNO tubular membrane and Ag-based sealant was readily constructed and applied to...A gas-tight BaCo 0.7 Fe 0.2 Nb 0.1 O 3-δ（BCFNO） tubular membrane was fabricated by hot pressure casting.And a membrane reactor with BCFNO tubular membrane and Ag-based sealant was readily constructed and applied to partial oxidation of CH4 in coke oven gas.At 875 ℃,95% of methane conversion,91% of H 2 and as high as 10 ml cm-2·min-1 of oxygen permeation flux were obtained.There was a good match in the coefficient of thermal expansion between Ag-based alloy and BCFNO membrane materials.The tubular BCFNO membrane reactor packed with Ni-based catalysts exhibited not only high activity but also good stability in hydrogen-enriched coke oven gas（COG） atmosphere.展开更多
The flow and concentration fields in a new style tubular stirred reactor were simulated by simulating the fluids dynamics(CFD),in which FLUENT software was used and the standard k-ε model and multiple reference frame...The flow and concentration fields in a new style tubular stirred reactor were simulated by simulating the fluids dynamics(CFD),in which FLUENT software was used and the standard k-ε model and multiple reference frame(MRF) were adopted. The various values of initial rotating speed and inlet flow rate were adopted. Simulations were validated with experimental residence time distribution(RTD) determination. It is shown that the fluid flow is very turbulent and the flow pattern approaches to the plug flow. The velocity increases from shaft to the end of impeller,and the gradient is enlarged by increasing the rotating speed. Comparison between RTD curves shows that agitation can improve the performance of reactor. As the flow rate increases,the mean residence time decreases proportionally,and the variance of RTD lessens as well. When rotating speed increases to a certain value,the variance of RTD is enlarged by increasing rotating speed,but the mean residence time has no obvious change.展开更多
Tubular flow reactors are mainly used in chemical industry and waste water discharged units. Control of output variables is very difficult because of the existence of high dead-time in these types of reactors. In the ...Tubular flow reactors are mainly used in chemical industry and waste water discharged units. Control of output variables is very difficult because of the existence of high dead-time in these types of reactors. In the present work, sodium hydroxide and acetic acid solutions were sent to the tubular flow reactor. The aim was to control p H at 7 in the nonlinear region. The p H control of a tubular flow reactor with high time delay and a highly nonlinear behavior in p H neutralization reaction was investigated experimentally in the face of the various load and set point changes. Firstly, efficiency of conventional Proportional-Integral-Derivative(PID) algorithm in the experiments was tested. Then self-tuning PID(STPID) control system was applied by using the ARMAX model. The model parameters were calculated from input–output data by using PRBS signal as disturbance and Bierman algorithm. Lastly, the experimental fuzzy control of p H based on fuzzy model was achieved to compare the success of fuzzy approach with the performance of other control cases studied.展开更多
Hydrodynamics in vertical tubular leaching reactor was studied in this work. Based on the observation of particle saltation in curved and square return bends, the inclined return bend was developed and examined. For t...Hydrodynamics in vertical tubular leaching reactor was studied in this work. Based on the observation of particle saltation in curved and square return bends, the inclined return bend was developed and examined. For the narrow and wide size distribution particle system, the method for calculating the particle holdup in upflow and downflow tubes was derived on the basis of generalized fluidization equation. The model of unit pressure drop was given and examined by experiments.展开更多
The thermal pyrolysis of natural gas as a clean hydrogen production route is examined. The concept of a double-walled reactor tube is proposed and implemented. Preliminary experiments using an external plasma heating ...The thermal pyrolysis of natural gas as a clean hydrogen production route is examined. The concept of a double-walled reactor tube is proposed and implemented. Preliminary experiments using an external plasma heating source are carried out to validate this concept. The results point out the efficient CH4 dissociation above 1850 K （CH4 conversion over 90%） and the key influence of the gas residence time. Simulations are performed to predict the conversion rate of CH4 at the reactor outlet, and are consistent with experimental tendencies. A solar reactor prototype featuring four independent double-walled tubes is then developed. The heat in high temperature process required for the endothermic reaction of natural gas pyrolysis is supplied by concentrated solar energy. The tubes are heated uniformly by radiation using the blackbody effect of a cavity-receiver absorbing the concentrated solar irradiation through a quartz window. The gas composition at the reactor outlet, the chemical conversion of CH4, and the yield to H2 are determined with respect to reaction temperature, inlet gas flow-rates, and feed gas composition. The longer the gas residence time, the higher the CH4 conversion and H2 yield, whereas the lower the amount of acetylene. A CH4 conversion of 99% and H2 yield of about 85% are measured at 1880 K with 30% CH4 in the feed gas （6 L/min injected and residence time of 18 ms）, A temperature increase from 1870 K to 1970 K does not improve the H2 yield.展开更多
基金the financial supports from Natural Science Foundation of Henan,China(No.212300410278)Henan Provincial Key Research and Development Program,China(No.212102310371)+1 种基金Henan Postdoctoral Foundation,China(No.202002020)China Postdoctoral Science Foundation(No.2020M682353).
文摘An acidic mixture of sulfuric and fluosilicic acid(H_(2)SO_(4)+H_(2)SiF_(6))was employed as lixiviant to enhance leaching of lithium from lepidolite.The H_(2)SiF_(6) was obtained as a byproduct of anhydrous hydrofluoric acid production,aiming to provide HF molecules.It was found that the HF molecules were the main reaction component and played a key role in strengthening the dissolution of lepidolite.Different factors,including mass ratio of ore/H_(2)SO_(4)/H_(2)SiF_(6),concentrations of H_(2)SO_(4) and H_(2)SiF_(6),leaching temperatures(40−80℃)and time(15−75 min),were investigated.Moreover,an efficient tubular reactor was employed to improve this acid leaching system.Under the optimal conditions(ore/H_(2)SO_(4)/H_(2)SiF_(6) mass ratio of 1:0.8:1.6,80 wt.% H_(2)SO_(4),15 wt.% H_(2)SiF_(6),80℃,15 min),97.9% of Li,96.4% of K,97.6% of Rb,96.7% of Cs and 81.4% of Al(mass fraction)were leached.Additionally,a two-step thermal process was proposed to remove fluorine of leaching slurry.This acid treatment using an acidic mixture of H_(2)SO_(4) and H_(2)SiF_(6) in a continuous tubular reactor shows potential as an alternative process to extract lithium from lepidolite.
基金Supported by the National Natural Science Foundation of China（20576105） the Natural Science Foundation of Hubei Province（2008CDA024） the Project of Academic Leaders in Wuhan（200851430490）
文摘Production of biodiesel with supercritical methanol is a green synthesis process.A study was carried out in a vertical tubular reactor with a length of 3700 mm and a diameter of 20 mm at 275-375°C,15 MPa,and molar ratio of methanol to soybean oil of 40︰1.The phase holdup,intermediate product,yield and axial distribution of methyl ester(ME) were investigated.Methanol and oil were mixed non-uniformly due to the formation of biodiesel and difference in their densities,even when the reaction system was in the supercritical state.From top to bottom,the phase holdup of methanol increased and that of oil decreased.As temperature increased,the concentrations of monoglyceride and diglyceride decreased gradually and the ME yield increased.When the temperature reached 300°C,the critical temperature of the system,the ME yield was 50%.Further increase in temperature led to a sharp in-crease of ME yield.However,at 375°C after 1200 s of reaction time,the decomposition rate of ME was greater than its formation rate,reducing the ME yield.
基金The financial support provided by the Project of National Natural Science Foundation of China(21822809&21978256)the Fundamental Research Funds for the Central Universitiesthe Foundation of State Key Laboratory of High-efficiency Utilization of Coal and Green Chemical Engineering(Grant No.2018-K23)are gratefully acknowledged.
文摘Ethane steam cracking process in an industrial reactor was investigated.An one-demsional(1D)steady-state model was developed firstly by using an improved molecular reaction scheme and was then simulated in Aspen Plus.A comparison of model results with industrial data and previously reported results showed that the model can predict the process kinetics more accurately.In addition,the validated model was used to study the effects of different process variables,including coil outlet temperature(COT),steam-to-ethane ratio and residence time on ethane conversion,ethylene selectivity,products yields,and coking rate.Finally,steady-state optimization was conducted to the operation of industrial reactor.The COT and steam-to-ethane ratio were taken as decision variables to maximize the annual operational profit.
基金the financial support from the National Natural Science Foundation of China (No. 21266022, No. 21466022)the National High Technology Research and Development Program 863 (2014AA022002, 2012AA101800-03, 2012AA021205-6, 2012AA021704)+1 种基金the Key Programs of the National Laboratory (No. SKLFZZB-201312)the International Science & Technology Cooperation Program of China (2014DFA61040)
文摘With the help of the ceramic foam research efforts and preparation techniques, the ZrO2 polycrystalline ceramic foam catalyst was synthesized, and its characteristics, including the crystal structure, the phase composition, the acid–base properties, and the microstructure, were analyzed by XRD, SEM, Py-IR, and BET techniques. The performance of the ZrO2 polycrystalline ceramic foam catalyst in a tubular reactor was investigated via biodiesel synthesis using S. wilsoniana oil and methanol. The effects of reaction conditions(i.e., reaction temperature, reaction pressure, and volume ratio of methanol to S. wilsoniana oil) on transesterification efficiency were investigated, and the reaction conditions were optimized using RSM. The optimum reaction temperature, reaction pressure, and volume ratio of methanol to S. wilsoniana oil were determined to be 290 ℃, 10 MPa, and 4:1, respectively. Under this condition, the FAME content in the product oil reached 98.38%. The performance of the ZrO2 polycrystalline ceramic foam catalyst synthesized in this work for biodiesel synthesis from S. wilsoniana oil with a moisture content of 7.1% and an acid value of 130.697 mg KOH/g was examined, and the FAME content in the product oil was found to be 93% and 97.67%, respectively. The FAME content in the product oil exceeded 97% after five consecutive cycles(12 h per cycle of use) of the catalyst. The proposed catalyst represents a new type of solid catalyst with excellent acid resistance, water resistance, esterification efficiency, and catalytic stability.
基金Supported by Iran Polymer and Petrochemical Institute
文摘In this study, rheological examination of the mixture of a tubular reactor in which methyl methacrylate was polymerized has been studied. The n(flow behavior index) value of Power Law Model of mixture contained in the reactor has been determined within the span of 0.3492 to 0.9889 by curve fitting. Employing these numerical data for velocity profile, the reactor has been modeled. Moreover, the functions of the reactor have been compared in the three modes of plug, mixed and laminar flow. The results obtained in this research indicate that the polymethyl methacrylate mixture contained in the reactor is pseudo-plastic. Moreover, as the conversion grows, the velocity profile starts as a parabolic profile and approaches the plug mode; although it never reaches the plug. The other conclusions borne in this study indicate that when the reactor's radius is decreased, the conversion rate grows. However, as decreasing the radius would also reduce the productions rate, this procedure is not economical. Finally, in this modeling, the amount of conversion is equal to 56.47% at the end and according to its laboratory proportion which is 55.88%, it has reached the conclusion that the modeling duly undertaken is applicable and valid.
文摘Ethylene glycol monoethyl ether acetate (EGEA), an excellent solvent, is prepared with ethylene oxide (EO) and ethyl acetate (EA) in a tubular reactor under suitable reaction condition. The single circulation yield can reach 81%. This technology is not only safe but also makes it possible to continuously produce EGEA in industry,with low content of high boiling point by-products.
文摘In this study, we present a model whereby the centre of the atomization channel is shown to be the optimal location for the spectrometric data acquisition in a quartz cell atomizer. The study aims to explore the hydride generation technique which is normally coupled with efficient thermal source to apply determination of heavy metals in water samples via spectrometric analysis. The arsenic hydride generation process and the atomization of the generated hydride in a quartz cell atomizer were studied analytically as model case studies. The hydride generation (HG) process was analyzed by adopting two hypotheses, the nascent hydrogen and formation of intermediate hydroboron species, where the results based on the second hypothesis are found to be more realistic for design purposes. Moreover, the release of the generated hydride from the liquid phase and their transport to the gas phase is simulated in a helical tubular section, in which the actual tubular section length required for separation is deduced. The analytical results have been verified experimentally by measuring the signal intensity for the free arsenic atoms against several reaction tube lengths, in which increasing the tubular section length from 12 cm to 100 cm results in signal amelioration by no more than 6.6%. Furthermore, the atomization of the hydride and the distribution of the generated free atoms are deduced in two configurations of tubular quartz atomizers. The results obtained from both studied cases illustrate that a high concentration of the free analyte atoms is generated in the first part of the atomization channel, saturates to a maximum in a position at the atomizer centre, and dissipates at the inside wall of the tubular atomizer before reaching the atomizer outlet edge, which is found to be in total agreement with the current understanding of atomization mechanism in tubular atomizer and emphasizes the fact that the centre of the quartz cell atomizer is the best location for the spectrometric data acquisition.
文摘This paper presents the results of polymeric deposit analysis in HP recycling system on two ethylene polymerization trains in tubular reactors when using mixed initiation (organic peroxides and oxygen) in the process of various grade production. It is demonstrated that polymers belong to the very low density type (with ρ in 0,860 to 0,900 g/cm3 range), due to ultra high branching. Consideration is given to known processes of that kind polymer production. There discussed the alternatives of different approaches to special process features found. It is stated that 80-year high pressure PE synthesis history has been keeping potential for the development.
基金supported by the National High Technology Research and Development Program of China (Project No. 2006AA11A189)
文摘A gas-tight BaCo 0.7 Fe 0.2 Nb 0.1 O 3-δ（BCFNO） tubular membrane was fabricated by hot pressure casting.And a membrane reactor with BCFNO tubular membrane and Ag-based sealant was readily constructed and applied to partial oxidation of CH4 in coke oven gas.At 875 ℃,95% of methane conversion,91% of H 2 and as high as 10 ml cm-2·min-1 of oxygen permeation flux were obtained.There was a good match in the coefficient of thermal expansion between Ag-based alloy and BCFNO membrane materials.The tubular BCFNO membrane reactor packed with Ni-based catalysts exhibited not only high activity but also good stability in hydrogen-enriched coke oven gas（COG） atmosphere.
基金Project(20050145029) supported by the PhD Program Foundation of Ministry of Education of ChinaProject supported by the Foundation of Excellent Talents of Science and Technology of Liaoning Province, China
文摘The flow and concentration fields in a new style tubular stirred reactor were simulated by simulating the fluids dynamics(CFD),in which FLUENT software was used and the standard k-ε model and multiple reference frame(MRF) were adopted. The various values of initial rotating speed and inlet flow rate were adopted. Simulations were validated with experimental residence time distribution(RTD) determination. It is shown that the fluid flow is very turbulent and the flow pattern approaches to the plug flow. The velocity increases from shaft to the end of impeller,and the gradient is enlarged by increasing the rotating speed. Comparison between RTD curves shows that agitation can improve the performance of reactor. As the flow rate increases,the mean residence time decreases proportionally,and the variance of RTD lessens as well. When rotating speed increases to a certain value,the variance of RTD is enlarged by increasing rotating speed,but the mean residence time has no obvious change.
文摘Tubular flow reactors are mainly used in chemical industry and waste water discharged units. Control of output variables is very difficult because of the existence of high dead-time in these types of reactors. In the present work, sodium hydroxide and acetic acid solutions were sent to the tubular flow reactor. The aim was to control p H at 7 in the nonlinear region. The p H control of a tubular flow reactor with high time delay and a highly nonlinear behavior in p H neutralization reaction was investigated experimentally in the face of the various load and set point changes. Firstly, efficiency of conventional Proportional-Integral-Derivative(PID) algorithm in the experiments was tested. Then self-tuning PID(STPID) control system was applied by using the ARMAX model. The model parameters were calculated from input–output data by using PRBS signal as disturbance and Bierman algorithm. Lastly, the experimental fuzzy control of p H based on fuzzy model was achieved to compare the success of fuzzy approach with the performance of other control cases studied.
文摘Hydrodynamics in vertical tubular leaching reactor was studied in this work. Based on the observation of particle saltation in curved and square return bends, the inclined return bend was developed and examined. For the narrow and wide size distribution particle system, the method for calculating the particle holdup in upflow and downflow tubes was derived on the basis of generalized fluidization equation. The model of unit pressure drop was given and examined by experiments.
基金European FP6 research project SOLHYCARB (Contract SES-CT-2006-19770)
文摘The thermal pyrolysis of natural gas as a clean hydrogen production route is examined. The concept of a double-walled reactor tube is proposed and implemented. Preliminary experiments using an external plasma heating source are carried out to validate this concept. The results point out the efficient CH4 dissociation above 1850 K （CH4 conversion over 90%） and the key influence of the gas residence time. Simulations are performed to predict the conversion rate of CH4 at the reactor outlet, and are consistent with experimental tendencies. A solar reactor prototype featuring four independent double-walled tubes is then developed. The heat in high temperature process required for the endothermic reaction of natural gas pyrolysis is supplied by concentrated solar energy. The tubes are heated uniformly by radiation using the blackbody effect of a cavity-receiver absorbing the concentrated solar irradiation through a quartz window. The gas composition at the reactor outlet, the chemical conversion of CH4, and the yield to H2 are determined with respect to reaction temperature, inlet gas flow-rates, and feed gas composition. The longer the gas residence time, the higher the CH4 conversion and H2 yield, whereas the lower the amount of acetylene. A CH4 conversion of 99% and H2 yield of about 85% are measured at 1880 K with 30% CH4 in the feed gas （6 L/min injected and residence time of 18 ms）, A temperature increase from 1870 K to 1970 K does not improve the H2 yield.
