This work presented the development and validation of an analytical method to predict the transient temperature field in the asphalt pavement.The governing equation for heat transfer was based on heat conduction radia...This work presented the development and validation of an analytical method to predict the transient temperature field in the asphalt pavement.The governing equation for heat transfer was based on heat conduction radiation and convection.An innovative time-dependent function was proposed to predict the pavement surface temperature with solar radiation and air temperature using dimensional analysis in order to simplify the complex heat exchange on the pavement surface.The parameters for the time-dependent pavement surface temperature function were obtained through the regression analysis of field measurement data.Assuming that the initial pavement temperature distribution was linear and the influence of the base course materials on the temperature of the upper asphalt layers was negligible,a close-form analytical solution of the temperature in asphalt layers was derived using Green's function.Finally,two numerical examples were presented to validate the model solutions with field temperature measurements.Analysis results show that the solution accuracy is in agreement with field data and the relative errors at a shallower depth are greater than those at a deeper one.Although the model is not sensitive to dramatic changes in climatic factors near the pavement surface,it is applicable for predicting pavement temperature field in cloudless days.展开更多
Heat losses from the furnaces depend on the design and size. The surface heat loss from the bottom of an industrial AC electric arc furnace (EAF) possesses an important fraction of overall losses. So in this study the...Heat losses from the furnaces depend on the design and size. The surface heat loss from the bottom of an industrial AC electric arc furnace (EAF) possesses an important fraction of overall losses. So in this study the transient temperature variation at the bottom of the EAF was investigated. The transient temperature analysis was carried out using MATLAB computer program. T=T(r, t) for different bottom lining layers was depicted.展开更多
The on-orhit transient temperature of reflector laminate film was analyzed by using finite element method （FEM）. Numerical simulation was used by FEM software ANSYS. Results reveal that the temperature levels of the...The on-orhit transient temperature of reflector laminate film was analyzed by using finite element method （FEM）. Numerical simulation was used by FEM software ANSYS. Results reveal that the temperature levels of the laminate composite membrane alternate greatly in the orbital period, which is about±80℃. This range exceeds the material ＇ s operating temperature level. So it is necessary to put effective thermal control into effect to the laminate composite membrane. There is temperature gradient in the thickness direction of the laminate composite membrane; there is a light change in Kevlar/Epoxy layer. The temperature of the laminate composite membrane is obviously lower than the seam＇ s temperature. Results provide reference to the thermal control of the inflatable reflector with high precision requirement.展开更多
Frost heave in seasonally frozen regions is a one-dimensional process that could severely damage infrastructure subgrades.Stress state,temperature and water migration are important factors for frost heave.This work in...Frost heave in seasonally frozen regions is a one-dimensional process that could severely damage infrastructure subgrades.Stress state,temperature and water migration are important factors for frost heave.This work investigated the effects of soil temperature and volumetric water content on the transient frost heave ratio during the freezing of saturated silty clay in an open system and analyzed the relationships between the transient frost heave ratio and freezing rate and between temperature gradient and frost heave rate.The results show that the frost heave ratio,frost heave rate,and freezing rate are positively correlated with the temperature gradient since the temperature gradient drives the water migration during freezing,indicating the transient temperature gradient could be used to evaluate the frost heave of saturated silty clay.The transient freezing rate and transient frost heave ratio are logarithmically related to the transient frost heave ratio and transient temperature gradient,respectively.The effects of transient temperature gradient on frost heave are the principal mechanism responsible for different frost heave characteristics and uneven frost heave along a subgrade of the same soil type.展开更多
Based on the analysis of factors affecting transient temperature field of aircraft fuel tank and coupled heat transfer mechanism, a mathematical model of transient coupled heat transfer, including the dynamic- chan...Based on the analysis of factors affecting transient temperature field of aircraft fuel tank and coupled heat transfer mechanism, a mathematical model of transient coupled heat transfer, including the dynamic- change of fuel quality, the internal heat transfer, the external aerodynamic convection and the radiation heat transfer, is established. Taking the aerodynamic convection and radiation heat transfer outside the tank as the third kinds of thermal boundary conditions for the thermal analysis of the fuel tank, calculation of internal and external coupling heat of fuel tank is decoupled. Ther^nal network method combined with hierarchical dynamic- grid is used to deal with the fuel consumption, and carry on the heat transfer analysis of the fuel tank. The numerical method for the transient temperature field of aircraft fuel tank is established. Through the simulation calculation, the transient temperature distribution of the fuel tank under different flight conditions is obtained, and the influence of the fuel mass and the external thermal environment on the temperature field is analyzed.展开更多
One of the primary reasons leading to bulging and cracking in a coke drum is the severe temperature gradient due to cyclic temperature variation. Based on the twodimensional heat conduction theory, an analytical solut...One of the primary reasons leading to bulging and cracking in a coke drum is the severe temperature gradient due to cyclic temperature variation. Based on the twodimensional heat conduction theory, an analytical solution of the transient temperature field in the coke drum is obtained, which is different from the known FEM results. The length of the coke drum is considered finite. The dynamic boundary conditions caused by fluid uninterrupted rising in oiling and watering stages are simulated with the iteration method. Numerical results show that the present theoretical model can accurately describe basic features of the transient temperature field in the coke drum. Effects of the geometry of the coke drum and the rising velocity of quench water on the axial temperature gradient are also discussed.展开更多
In oil and gas well cementing processes,accurately predicting the bottom hole circulating temperature(BHCT)is critical to ensuring effective zonal isolation.Overestimating the temperature can lead to excessive retarda...In oil and gas well cementing processes,accurately predicting the bottom hole circulating temperature(BHCT)is critical to ensuring effective zonal isolation.Overestimating the temperature can lead to excessive retardation issues,while underestimation can cause cementing accidents.Current methods for calculating the BHCT of cement slurry typically simplify the cementing processes to a single-fluid circulation and ignore the impact of pre-cementing processes on temperature,leading to significant discrepancies between calculated and actual results.In this study,the wellbore and formation are simplified into a two-dimensional axisymmetric structure,and a mathematical model of the temperature field under multi-fluid and multi-step conditions is established based on the law of energy conservation.The finite volume method was used to discretize the model,and a transient temperature field solver for the entire cementing process was developed,which can numerically calculate the temperature of any fluid at any time,any location.For an actual well example,the temperature distribution of the wellbore and formation after casing running is taken as the initial condition.Numerical calculations were performed sequentially to calculate the temperature fields of circulation flushing,wellbore preparation,and cementing,as well as the BHCT of the cement slurry.The study reveals that during the circulation flushing stage,the maximum temperature point in the wellbore is located at a distance of about 366 m above the bottom of the well.In the wellbore preparation stage,due to static heat exchange,the maximum temperature point gradually shifts to the bottom of the well.The BHCT of cement slurry changes continuously under cementing processes with multi-fluid and multi-step,making it a transient value.The BHCT of the lead slurry and tail slurry are not equal,with the maximum BHCT of the tail slurry being 2.46°C higher than that of the lead slurry.If circulation flushing and wellbore preparation are not considered,the calculated BHCT of the cement slurry will have errors of+6.8%and-1.9%.The study highlighted that considering thermal effects of all cementing stages,such as circulation flushing and wellbore preparation,in BHCT calculations can help improve prediction accuracy.展开更多
Based on the actual operation parameters and temperature-dependent material properties of a gas turbine unit,composite cooling blade model and corresponding reliable boundary conditions were established.Transient ther...Based on the actual operation parameters and temperature-dependent material properties of a gas turbine unit,composite cooling blade model and corresponding reliable boundary conditions were established.Transient thermal-fluid-solid coupling simulations were then comprehensively conducted to analyze the transient flow and the temperature field of the blade under startup,shutdown,and variable loads condition.Combined with the obtained transient temperature data,the non-linear finite element method was exploited to examine the effect of these transient operations on the turbine blade thermal stress characteristics.Results show that the temperature and pressure on the blade surface increase with the load level and vice versa.As the startup process progresses,the film cooling effectiveness and the heat convection of airflows inside the blade continuously grow;high-temperature areas on the pressure surface and along the trailing edge of the blade tip gradually disappear.Locally high-temperature zones with the maximum of 1280 K are generated at the air inlet and outlet of the blade platform and the leading edge of the blade tip.The high thermal stresses detected on the higher temperature side of the temperature gradient are commonly generated in places with large temperature gradients and significant geometry variations.For the startup/shutdown process,the rate of increase/decrease of the thermal stress is positively correlated with the load variation rate.A slight variation rate of the load(1.52%/min)can lead to an apparent alteration(41%)to the thermal stress.In operations under action of the variable load,although thermal stress is less sensitive to the load variation,the rising or falling rate of the exerted load still needs to be carefully controlled due to the highly leveled thermal stresses.展开更多
A novel double-slab Nd:YAG laser, which uses face-pumped slab medium cooled by liquid with different temperatures on both sides, is proposed. The thermal distortion of wavefront caused by the non-uniform temperature d...A novel double-slab Nd:YAG laser, which uses face-pumped slab medium cooled by liquid with different temperatures on both sides, is proposed. The thermal distortion of wavefront caused by the non-uniform temperature distribution in the laser gain media can be self-compensated. According to the method of operation, the models of the temperature distribution and stress are presented, and the analytic solutions for the model are derived. Furthermore, the numerical simulations with pulse pumping energy of 10 J and repetition frequencies of 500 and 1000 Hz are calculated respectively for Nd:YAG laser medium. The simulation results show that the temperature gradient remains the approximative linearity, and the heat stress is within the extreme range. Then the absorption coefficient is also discussed. The result indicates that the doping concentration cannot be too large for the high repetition frequency laser. It has been proved that the high repetition frequency, high laser beam quality, and high average outp展开更多
Based on non-equilibrium thermodynamic theory, a temperature field model of gun muzzle is setup We obtain not only a solitary solution, but also a bifurcation solution. The physical picture of the solutions is corresp...Based on non-equilibrium thermodynamic theory, a temperature field model of gun muzzle is setup We obtain not only a solitary solution, but also a bifurcation solution. The physical picture of the solutions is corresponding to the center flame and secondary flame of the gun muzzle.展开更多
In this paper, instead of with the more expensive Fourier Transform Infrared Spectrometer(FTIR) a new technique of Temperature Programmed Transient Response(TP-TR) has been used with gas chromatography. Therefore, the...In this paper, instead of with the more expensive Fourier Transform Infrared Spectrometer(FTIR) a new technique of Temperature Programmed Transient Response(TP-TR) has been used with gas chromatography. Therefore, the TP-TR will be applied more widespreadly than ever before. With the technique of TP-TR and electric conductivity, the study is on the reaction mechanism and the adsorption behavior of the reactants and products to the present catalyst Mo-V-Nb/Al_2O_3 in the reaction from ethane through oxydehydrogenation to ethylene as the product. By Range-Kutta-Gill and Margarat methods, the kinetic parameters of the reaction elementary steps (i.e. rate constants, active energies and frequency factors) have been evaluated. The mathematical treatment coincides with the experimental results.展开更多
In order to predict the long-term rutting of asphalt pavement, the effective temperature for pavement rutting is calculated using the numerical simulation method. The transient temperature field of asphalt pavement wa...In order to predict the long-term rutting of asphalt pavement, the effective temperature for pavement rutting is calculated using the numerical simulation method. The transient temperature field of asphalt pavement was simulated based on actual meteorological data of Nanjing. 24-hour rutting development under a transient temperature field was calculated in each month. The rutting depth accumulated under the static temperature field was also estimated and the relationship between constant temperature parameters was analyzed. Then the effective temperature for pavement rutting was determined based on the rutting equivalence principle. The results show that the monthly effective temperature is above 40 t in July and August, while in June and September it ranges from 30 to 40 Rutting development can be ignored when the monthly effective temperature is less than 30 t. The yearly effective temperature for rutting in Nanjing is around 38. 5 t. The long-term rutting prediction model based on the effective temperature can reflect the influences of meteorological factors and traffic time distribution.展开更多
There currently does not exist in industry a reliable method for the detection of rail foot flaws.Like their head-based counterparts,foot flaws result in broken rail with potentially catastrophic consequences.A propos...There currently does not exist in industry a reliable method for the detection of rail foot flaws.Like their head-based counterparts,foot flaws result in broken rail with potentially catastrophic consequences.A proposed area of research for the detection of these flaws is thermography,a non-contact method of measuring and analysing infrared emissions from an object under test.In industry,active excitation thermography is the most common,requiring an excitation source.This paper will present a temperature measurement system and a method of transient temperature extraction from the running rails for the effects of a passing train to evaluate heat transfer in the practical rail environment.The outcomes of these results will provide future direction in the development of a rail heat transfer model and determine if train passage provides enough active excitation for a thermography-based detection technique.展开更多
The thermal conditions like the temperature distribution and the heat fluxes during metal cutting have a major influence on the machinability, the tool lifetime, the metallurgical structure and thus the functionality ...The thermal conditions like the temperature distribution and the heat fluxes during metal cutting have a major influence on the machinability, the tool lifetime, the metallurgical structure and thus the functionality of the work piece. This in particular applies for manufacturing processes like milling, drilling and turning for high-value turbomachinery components like impellers, combustion engines and compressors of the aerospace and automotive industry as well as energy generation, which play a major role in modern societies. However, numerous analytical and experimental efforts have been conducted in order to understand the thermal conditions in metal cutting, yet many questions still prevail. Most models are based on a stationary point of view and do not include time dependent effects like in intensity and distribution varying heat sources, varying engagement conditions and progressive tool wear. In order to cover such transient physics an analytical approach based on Green＇s functions for the solution of the partial differential equations of unsteady heat conduction in solids is used to model entire transient temperature fields. The validation of the model is carried out in orthogonal cutting experiments not only punctually but also for entire temperature fields. For these experiments an integrated measurement of prevailing cutting force and temperature fields in the tool and the chip by means of high-speed thermography were applied. The thermal images were analyzed with regard to thermodynamic energy balancing in order to derive the heat partition between tool, chips and workpiece. The thus calculated heat flow into the tool was subsequently used in order to analytically model the transient volumetric temperature fields in the tool. The described methodology enables the modeling of the transient thermal state in the cutting zone and particular in the tool, which is directly linked to phenomena like tool wear and workpiece surface modifications.展开更多
C_(5)F_(10)O/CO_(2)gas mixture is one of the most promising alternatives to SF_(6)as an insulating gas in high-voltage switchgear.As a key performance index in product design,the temperature rise characteristics are r...C_(5)F_(10)O/CO_(2)gas mixture is one of the most promising alternatives to SF_(6)as an insulating gas in high-voltage switchgear.As a key performance index in product design,the temperature rise characteristics are rarely reported.In this paper,the thermodynamic parameters of C_(5)F_(10)O/CO_(2)gas mixture were calculated first.Then,the calculation model of transient temperature rise was constructed for a 252 kV/3150 A bus,and a temperature rise experimental platform was built to verify the reliability of the proposed calculation model.On this basis,the influence of different factors such as load current,charging pressure,mixing ratio,and structure size on the temperature rise of the bus was further analysed,and it is found that increasing the charging pressure and the mixing ratio of C5F10O could effectively reduce the bus temperature rise but it still could not reach the level of SF_(6).The main structure size that affects the temperature rise of the bus is the outer diameter of the conductor,which increases by 10.2%,and the temperature rise is the same as that of the original SF_(6)bus.Finally,a high-precision bus temperature rise surrogate model,which combined with the Latin hypercube model,the coefficient of prognosis,and the Kriging fitting method was established to facilitate the structural design.展开更多
The ratio, of the temperature gradient at the solidification front to the solidification rate of solid-liquid interface, plays a large part in columnar grain growth. The transient temperature fields of directional sol...The ratio, of the temperature gradient at the solidification front to the solidification rate of solid-liquid interface, plays a large part in columnar grain growth. The transient temperature fields of directional solidification of Al-Ni-Co alloy were studied by employing a finite element method. The temperature gradient at the solidification front and the solidification rate were analyzed for molten steels pouring at different temperatures. The results show that with different initial pouring temperatures, the individual ratio of the temperature gradient at solidification front to the solidification rate soars up in the initial stage of solidification, then varies within 2,000-6,000 ℃.s.cm2, and finally goes down rapidly and even tend to be closed to each other when the solidification thickness reaches 5-6 cm. The simulation result is consistent with the practical production which can provide an available reference for process optimization of directional solidified Al-Ni-Co alloy.展开更多
A modified temperature-phase transformation-stress coupled 3D non-linear mathematical model and a series of subroutines on the non-liner MARC (MARC Analysis Research Corporation) are developed. Then this modified mode...A modified temperature-phase transformation-stress coupled 3D non-linear mathematical model and a series of subroutines on the non-liner MARC (MARC Analysis Research Corporation) are developed. Then this modified model has been utilized to simulate the heat treatment processes of 280 connecting rod of 16 V280ZJ diesel locomotive. The simulation results are basically in agreement with the experiments, which testify that the mathematical model and method are feasible. In addition, the simulation can not only obtain the transient temperature and micro structure of heat treatment process, but also provide a sound scientific basis for the heat treatment workers.展开更多
A mathematical model for one-dimensional heat transfer in pipelines undergoing freezing induced by liquid nitrogen is elaborated.The basic premise of this technology is that the content within a pipeline is frozen to ...A mathematical model for one-dimensional heat transfer in pipelines undergoing freezing induced by liquid nitrogen is elaborated.The basic premise of this technology is that the content within a pipeline is frozen to form a plug or two plugs at a position upstream and downstream from a location where work a modification or a repair must be executed.Based on the variable separation method,the present model aims to solve the related coupled heat conduction and moving-boundary phase change problem.An experiment with a 219 mm long pipe,where water was taken as the plugging agent,is presented to demonstrate the relevance and reliability of the proposed model(results show that the error is within 18%).Thereafter,the model is applied to predict the cooling and freezing process of pipelines with different inner diameters at different liquid nitrogen refrigeration temperatures when water is used as the plugging agent.展开更多
This paper investigated the fire resistance of CSBs with various parameters under high temperature rise due to fire using finite element software ABAQUS. The mechanical parameters of CSBs are analyzed, including load-...This paper investigated the fire resistance of CSBs with various parameters under high temperature rise due to fire using finite element software ABAQUS. The mechanical parameters of CSBs are analyzed, including load-bearing capacity and the temperature distribution during the heating process. Through structural analysis simulation of the entire heating process, the structural response of the CSBs is divided into five stages: elastic stage, elastic-plastic stage, self-balancing stage, catenary stage and ultimate destruction stage. The results indicate that the opening diameter-to-height ratio, opening spacing-to-height ratio and load ratio significantly affect the structural responses of CSBs in fire, followed by opening shape as secondary effects. In all the numerical analyzes, CSBs are analyzed with a uniformly distributed load and having simply supported boundary conditions.展开更多
With the rapid advancements in high-speed train technology,the importance of ensuring the safety of train operations has become paramount.Bearings,being a critical component of train bogies,have garnered significant a...With the rapid advancements in high-speed train technology,the importance of ensuring the safety of train operations has become paramount.Bearings,being a critical component of train bogies,have garnered significant attention for their role in maintaining safety standards.Monitoring the temperature of bearings to evaluate their motion state is a common practice in high-speed trains,emphasizing the need for further research into temperature fluctuations.In this study,a dynamic model is developed for the bearing rotor system of high-speed trains.By considering the contact points between raceways and rolling elements,the power loss in the bearing is obtained and a transient temperature-field model of the system is established.The relationship between node temperature and factors such as ambient temperature,train running speed,and load is illustrated,with a detailed presentation of the influence of bearing fault type and size on node temperature.The analysis results reveal that the node temperature increases with higher values corresponding to those quantifiable factors and is most affected by rolling element fault.Additionally,it is observed that the temperature rises rapidly in the initial stage and gradually flattens out over time.The comparative analysis of temperature under different fault conditions shows that the node temperature is most affected by the rolling element fault.Experiments and actual line temperature data are used to verify the validity of the model.The comparison results show that the simulation aligns well with experimental and line data.The transient temperature-field model of the bearing rotor system in high-speed trains can effectively simulate and predict the temperature change process of each node of the system.The simulation results hold certain theoretical guiding significance for further research and practical applications in ensuring train operation safety.展开更多
基金Project(2012zzts019)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(201306370121)supported by State Scholarship Fund of ChinaProject(51248006)supported by the National Natural Science Foundation,China
文摘This work presented the development and validation of an analytical method to predict the transient temperature field in the asphalt pavement.The governing equation for heat transfer was based on heat conduction radiation and convection.An innovative time-dependent function was proposed to predict the pavement surface temperature with solar radiation and air temperature using dimensional analysis in order to simplify the complex heat exchange on the pavement surface.The parameters for the time-dependent pavement surface temperature function were obtained through the regression analysis of field measurement data.Assuming that the initial pavement temperature distribution was linear and the influence of the base course materials on the temperature of the upper asphalt layers was negligible,a close-form analytical solution of the temperature in asphalt layers was derived using Green's function.Finally,two numerical examples were presented to validate the model solutions with field temperature measurements.Analysis results show that the solution accuracy is in agreement with field data and the relative errors at a shallower depth are greater than those at a deeper one.Although the model is not sensitive to dramatic changes in climatic factors near the pavement surface,it is applicable for predicting pavement temperature field in cloudless days.
文摘Heat losses from the furnaces depend on the design and size. The surface heat loss from the bottom of an industrial AC electric arc furnace (EAF) possesses an important fraction of overall losses. So in this study the transient temperature variation at the bottom of the EAF was investigated. The transient temperature analysis was carried out using MATLAB computer program. T=T(r, t) for different bottom lining layers was depicted.
文摘The on-orhit transient temperature of reflector laminate film was analyzed by using finite element method （FEM）. Numerical simulation was used by FEM software ANSYS. Results reveal that the temperature levels of the laminate composite membrane alternate greatly in the orbital period, which is about±80℃. This range exceeds the material ＇ s operating temperature level. So it is necessary to put effective thermal control into effect to the laminate composite membrane. There is temperature gradient in the thickness direction of the laminate composite membrane; there is a light change in Kevlar/Epoxy layer. The temperature of the laminate composite membrane is obviously lower than the seam＇ s temperature. Results provide reference to the thermal control of the inflatable reflector with high precision requirement.
基金supported by the National Natural Science Foundation of China(No.51808128)the Natural Science Foundation of Fujian Province(No.2022J01091)。
文摘Frost heave in seasonally frozen regions is a one-dimensional process that could severely damage infrastructure subgrades.Stress state,temperature and water migration are important factors for frost heave.This work investigated the effects of soil temperature and volumetric water content on the transient frost heave ratio during the freezing of saturated silty clay in an open system and analyzed the relationships between the transient frost heave ratio and freezing rate and between temperature gradient and frost heave rate.The results show that the frost heave ratio,frost heave rate,and freezing rate are positively correlated with the temperature gradient since the temperature gradient drives the water migration during freezing,indicating the transient temperature gradient could be used to evaluate the frost heave of saturated silty clay.The transient freezing rate and transient frost heave ratio are logarithmically related to the transient frost heave ratio and transient temperature gradient,respectively.The effects of transient temperature gradient on frost heave are the principal mechanism responsible for different frost heave characteristics and uneven frost heave along a subgrade of the same soil type.
基金Sponsored by the National Natural Science Foundation of China(Grant No.51676055 and 51536001)
文摘Based on the analysis of factors affecting transient temperature field of aircraft fuel tank and coupled heat transfer mechanism, a mathematical model of transient coupled heat transfer, including the dynamic- change of fuel quality, the internal heat transfer, the external aerodynamic convection and the radiation heat transfer, is established. Taking the aerodynamic convection and radiation heat transfer outside the tank as the third kinds of thermal boundary conditions for the thermal analysis of the fuel tank, calculation of internal and external coupling heat of fuel tank is decoupled. Ther^nal network method combined with hierarchical dynamic- grid is used to deal with the fuel consumption, and carry on the heat transfer analysis of the fuel tank. The numerical method for the transient temperature field of aircraft fuel tank is established. Through the simulation calculation, the transient temperature distribution of the fuel tank under different flight conditions is obtained, and the influence of the fuel mass and the external thermal environment on the temperature field is analyzed.
基金Project supported by the National Natural Science Foundation of China (Nos. 10372035 and10902043)the Key Laboratory of Diagnosis of Fault in Engineering Structures of Guangdong Province of China
文摘One of the primary reasons leading to bulging and cracking in a coke drum is the severe temperature gradient due to cyclic temperature variation. Based on the twodimensional heat conduction theory, an analytical solution of the transient temperature field in the coke drum is obtained, which is different from the known FEM results. The length of the coke drum is considered finite. The dynamic boundary conditions caused by fluid uninterrupted rising in oiling and watering stages are simulated with the iteration method. Numerical results show that the present theoretical model can accurately describe basic features of the transient temperature field in the coke drum. Effects of the geometry of the coke drum and the rising velocity of quench water on the axial temperature gradient are also discussed.
基金supported by the National Natural Science Foundation of China(No.U22B6003 and No.52274010)the China Scholarship Council(No.202008080235)。
文摘In oil and gas well cementing processes,accurately predicting the bottom hole circulating temperature(BHCT)is critical to ensuring effective zonal isolation.Overestimating the temperature can lead to excessive retardation issues,while underestimation can cause cementing accidents.Current methods for calculating the BHCT of cement slurry typically simplify the cementing processes to a single-fluid circulation and ignore the impact of pre-cementing processes on temperature,leading to significant discrepancies between calculated and actual results.In this study,the wellbore and formation are simplified into a two-dimensional axisymmetric structure,and a mathematical model of the temperature field under multi-fluid and multi-step conditions is established based on the law of energy conservation.The finite volume method was used to discretize the model,and a transient temperature field solver for the entire cementing process was developed,which can numerically calculate the temperature of any fluid at any time,any location.For an actual well example,the temperature distribution of the wellbore and formation after casing running is taken as the initial condition.Numerical calculations were performed sequentially to calculate the temperature fields of circulation flushing,wellbore preparation,and cementing,as well as the BHCT of the cement slurry.The study reveals that during the circulation flushing stage,the maximum temperature point in the wellbore is located at a distance of about 366 m above the bottom of the well.In the wellbore preparation stage,due to static heat exchange,the maximum temperature point gradually shifts to the bottom of the well.The BHCT of cement slurry changes continuously under cementing processes with multi-fluid and multi-step,making it a transient value.The BHCT of the lead slurry and tail slurry are not equal,with the maximum BHCT of the tail slurry being 2.46°C higher than that of the lead slurry.If circulation flushing and wellbore preparation are not considered,the calculated BHCT of the cement slurry will have errors of+6.8%and-1.9%.The study highlighted that considering thermal effects of all cementing stages,such as circulation flushing and wellbore preparation,in BHCT calculations can help improve prediction accuracy.
基金the National Natural Science Foundation of China(NSFC)(No.52076173)the China Postdoctoral Science Foundation(No.2020M680157)the Fundamental Research Fund of the Central Universities(No.sxxj032020009)for funding。
文摘Based on the actual operation parameters and temperature-dependent material properties of a gas turbine unit,composite cooling blade model and corresponding reliable boundary conditions were established.Transient thermal-fluid-solid coupling simulations were then comprehensively conducted to analyze the transient flow and the temperature field of the blade under startup,shutdown,and variable loads condition.Combined with the obtained transient temperature data,the non-linear finite element method was exploited to examine the effect of these transient operations on the turbine blade thermal stress characteristics.Results show that the temperature and pressure on the blade surface increase with the load level and vice versa.As the startup process progresses,the film cooling effectiveness and the heat convection of airflows inside the blade continuously grow;high-temperature areas on the pressure surface and along the trailing edge of the blade tip gradually disappear.Locally high-temperature zones with the maximum of 1280 K are generated at the air inlet and outlet of the blade platform and the leading edge of the blade tip.The high thermal stresses detected on the higher temperature side of the temperature gradient are commonly generated in places with large temperature gradients and significant geometry variations.For the startup/shutdown process,the rate of increase/decrease of the thermal stress is positively correlated with the load variation rate.A slight variation rate of the load(1.52%/min)can lead to an apparent alteration(41%)to the thermal stress.In operations under action of the variable load,although thermal stress is less sensitive to the load variation,the rising or falling rate of the exerted load still needs to be carefully controlled due to the highly leveled thermal stresses.
文摘A novel double-slab Nd:YAG laser, which uses face-pumped slab medium cooled by liquid with different temperatures on both sides, is proposed. The thermal distortion of wavefront caused by the non-uniform temperature distribution in the laser gain media can be self-compensated. According to the method of operation, the models of the temperature distribution and stress are presented, and the analytic solutions for the model are derived. Furthermore, the numerical simulations with pulse pumping energy of 10 J and repetition frequencies of 500 and 1000 Hz are calculated respectively for Nd:YAG laser medium. The simulation results show that the temperature gradient remains the approximative linearity, and the heat stress is within the extreme range. Then the absorption coefficient is also discussed. The result indicates that the doping concentration cannot be too large for the high repetition frequency laser. It has been proved that the high repetition frequency, high laser beam quality, and high average outp
文摘Based on non-equilibrium thermodynamic theory, a temperature field model of gun muzzle is setup We obtain not only a solitary solution, but also a bifurcation solution. The physical picture of the solutions is corresponding to the center flame and secondary flame of the gun muzzle.
文摘In this paper, instead of with the more expensive Fourier Transform Infrared Spectrometer(FTIR) a new technique of Temperature Programmed Transient Response(TP-TR) has been used with gas chromatography. Therefore, the TP-TR will be applied more widespreadly than ever before. With the technique of TP-TR and electric conductivity, the study is on the reaction mechanism and the adsorption behavior of the reactants and products to the present catalyst Mo-V-Nb/Al_2O_3 in the reaction from ethane through oxydehydrogenation to ethylene as the product. By Range-Kutta-Gill and Margarat methods, the kinetic parameters of the reaction elementary steps (i.e. rate constants, active energies and frequency factors) have been evaluated. The mathematical treatment coincides with the experimental results.
基金The National Natural Science Foundation of China(No.51378121)the Fok Ying Tung Education Foundation(No.141076)the Scientific Innovation Research of College Graduates in Jiangsu Province(No.KYLX_0164)
文摘In order to predict the long-term rutting of asphalt pavement, the effective temperature for pavement rutting is calculated using the numerical simulation method. The transient temperature field of asphalt pavement was simulated based on actual meteorological data of Nanjing. 24-hour rutting development under a transient temperature field was calculated in each month. The rutting depth accumulated under the static temperature field was also estimated and the relationship between constant temperature parameters was analyzed. Then the effective temperature for pavement rutting was determined based on the rutting equivalence principle. The results show that the monthly effective temperature is above 40 t in July and August, while in June and September it ranges from 30 to 40 Rutting development can be ignored when the monthly effective temperature is less than 30 t. The yearly effective temperature for rutting in Nanjing is around 38. 5 t. The long-term rutting prediction model based on the effective temperature can reflect the influences of meteorological factors and traffic time distribution.
基金The work was supported by the Australasian Centre for Rail Innovation under its HH01B—Evaluating infrared imaging and laser ultrasonics as detectors of rail foot flaws project.
文摘There currently does not exist in industry a reliable method for the detection of rail foot flaws.Like their head-based counterparts,foot flaws result in broken rail with potentially catastrophic consequences.A proposed area of research for the detection of these flaws is thermography,a non-contact method of measuring and analysing infrared emissions from an object under test.In industry,active excitation thermography is the most common,requiring an excitation source.This paper will present a temperature measurement system and a method of transient temperature extraction from the running rails for the effects of a passing train to evaluate heat transfer in the practical rail environment.The outcomes of these results will provide future direction in the development of a rail heat transfer model and determine if train passage provides enough active excitation for a thermography-based detection technique.
文摘The thermal conditions like the temperature distribution and the heat fluxes during metal cutting have a major influence on the machinability, the tool lifetime, the metallurgical structure and thus the functionality of the work piece. This in particular applies for manufacturing processes like milling, drilling and turning for high-value turbomachinery components like impellers, combustion engines and compressors of the aerospace and automotive industry as well as energy generation, which play a major role in modern societies. However, numerous analytical and experimental efforts have been conducted in order to understand the thermal conditions in metal cutting, yet many questions still prevail. Most models are based on a stationary point of view and do not include time dependent effects like in intensity and distribution varying heat sources, varying engagement conditions and progressive tool wear. In order to cover such transient physics an analytical approach based on Green＇s functions for the solution of the partial differential equations of unsteady heat conduction in solids is used to model entire transient temperature fields. The validation of the model is carried out in orthogonal cutting experiments not only punctually but also for entire temperature fields. For these experiments an integrated measurement of prevailing cutting force and temperature fields in the tool and the chip by means of high-speed thermography were applied. The thermal images were analyzed with regard to thermodynamic energy balancing in order to derive the heat partition between tool, chips and workpiece. The thus calculated heat flow into the tool was subsequently used in order to analytically model the transient volumetric temperature fields in the tool. The described methodology enables the modeling of the transient thermal state in the cutting zone and particular in the tool, which is directly linked to phenomena like tool wear and workpiece surface modifications.
基金Sichuan Science and Technology Program,Grant/Award Number:2023NSFSC0297。
文摘C_(5)F_(10)O/CO_(2)gas mixture is one of the most promising alternatives to SF_(6)as an insulating gas in high-voltage switchgear.As a key performance index in product design,the temperature rise characteristics are rarely reported.In this paper,the thermodynamic parameters of C_(5)F_(10)O/CO_(2)gas mixture were calculated first.Then,the calculation model of transient temperature rise was constructed for a 252 kV/3150 A bus,and a temperature rise experimental platform was built to verify the reliability of the proposed calculation model.On this basis,the influence of different factors such as load current,charging pressure,mixing ratio,and structure size on the temperature rise of the bus was further analysed,and it is found that increasing the charging pressure and the mixing ratio of C5F10O could effectively reduce the bus temperature rise but it still could not reach the level of SF_(6).The main structure size that affects the temperature rise of the bus is the outer diameter of the conductor,which increases by 10.2%,and the temperature rise is the same as that of the original SF_(6)bus.Finally,a high-precision bus temperature rise surrogate model,which combined with the Latin hypercube model,the coefficient of prognosis,and the Kriging fitting method was established to facilitate the structural design.
文摘The ratio, of the temperature gradient at the solidification front to the solidification rate of solid-liquid interface, plays a large part in columnar grain growth. The transient temperature fields of directional solidification of Al-Ni-Co alloy were studied by employing a finite element method. The temperature gradient at the solidification front and the solidification rate were analyzed for molten steels pouring at different temperatures. The results show that with different initial pouring temperatures, the individual ratio of the temperature gradient at solidification front to the solidification rate soars up in the initial stage of solidification, then varies within 2,000-6,000 ℃.s.cm2, and finally goes down rapidly and even tend to be closed to each other when the solidification thickness reaches 5-6 cm. The simulation result is consistent with the practical production which can provide an available reference for process optimization of directional solidified Al-Ni-Co alloy.
基金The authors are grateful for financial support from the National Natural Science Foundation of China (Grant No. 50075053). Acknowledgement is also due to workers Liu, Yan and Chen who provided help in the micro structure.
文摘A modified temperature-phase transformation-stress coupled 3D non-linear mathematical model and a series of subroutines on the non-liner MARC (MARC Analysis Research Corporation) are developed. Then this modified model has been utilized to simulate the heat treatment processes of 280 connecting rod of 16 V280ZJ diesel locomotive. The simulation results are basically in agreement with the experiments, which testify that the mathematical model and method are feasible. In addition, the simulation can not only obtain the transient temperature and micro structure of heat treatment process, but also provide a sound scientific basis for the heat treatment workers.
文摘A mathematical model for one-dimensional heat transfer in pipelines undergoing freezing induced by liquid nitrogen is elaborated.The basic premise of this technology is that the content within a pipeline is frozen to form a plug or two plugs at a position upstream and downstream from a location where work a modification or a repair must be executed.Based on the variable separation method,the present model aims to solve the related coupled heat conduction and moving-boundary phase change problem.An experiment with a 219 mm long pipe,where water was taken as the plugging agent,is presented to demonstrate the relevance and reliability of the proposed model(results show that the error is within 18%).Thereafter,the model is applied to predict the cooling and freezing process of pipelines with different inner diameters at different liquid nitrogen refrigeration temperatures when water is used as the plugging agent.
文摘This paper investigated the fire resistance of CSBs with various parameters under high temperature rise due to fire using finite element software ABAQUS. The mechanical parameters of CSBs are analyzed, including load-bearing capacity and the temperature distribution during the heating process. Through structural analysis simulation of the entire heating process, the structural response of the CSBs is divided into five stages: elastic stage, elastic-plastic stage, self-balancing stage, catenary stage and ultimate destruction stage. The results indicate that the opening diameter-to-height ratio, opening spacing-to-height ratio and load ratio significantly affect the structural responses of CSBs in fire, followed by opening shape as secondary effects. In all the numerical analyzes, CSBs are analyzed with a uniformly distributed load and having simply supported boundary conditions.
基金S&T Program of Hebei,Grant/Award Number:21567622HNational Natural Science Foundation of China,Grant/Award Numbers:12072208,12172235,12302067,12393780,52072249College Education Scientific Research Project of Hebei Province,Grant/Award Number:JZX2024006。
文摘With the rapid advancements in high-speed train technology,the importance of ensuring the safety of train operations has become paramount.Bearings,being a critical component of train bogies,have garnered significant attention for their role in maintaining safety standards.Monitoring the temperature of bearings to evaluate their motion state is a common practice in high-speed trains,emphasizing the need for further research into temperature fluctuations.In this study,a dynamic model is developed for the bearing rotor system of high-speed trains.By considering the contact points between raceways and rolling elements,the power loss in the bearing is obtained and a transient temperature-field model of the system is established.The relationship between node temperature and factors such as ambient temperature,train running speed,and load is illustrated,with a detailed presentation of the influence of bearing fault type and size on node temperature.The analysis results reveal that the node temperature increases with higher values corresponding to those quantifiable factors and is most affected by rolling element fault.Additionally,it is observed that the temperature rises rapidly in the initial stage and gradually flattens out over time.The comparative analysis of temperature under different fault conditions shows that the node temperature is most affected by the rolling element fault.Experiments and actual line temperature data are used to verify the validity of the model.The comparison results show that the simulation aligns well with experimental and line data.The transient temperature-field model of the bearing rotor system in high-speed trains can effectively simulate and predict the temperature change process of each node of the system.The simulation results hold certain theoretical guiding significance for further research and practical applications in ensuring train operation safety.
