Temperature is one of the important loads for designing slab track. The characteristic of slab track tem- perature varies greatly with different regional climates. In this work, a bi-block slab track model was built u...Temperature is one of the important loads for designing slab track. The characteristic of slab track tem- perature varies greatly with different regional climates. In this work, a bi-block slab track model was built under outdoor conditions in Chengdu area; the statistical characteristic of temperature gradient in track slab and the relationship between temperature gradient and surface air temperature were tested and analyzed. The results show that the track slab temperature gradient will vary periodically according to the surface air temperature, and show a clear nonlinearity along the height direction. The temperature gradient distribution is extremely uneven： the temperature gradient in the top part of the track slab is larger than that in the bottom part; the most frequently occurring temperature gradient of the track slab is around -3.5 ℃/m and more than 75 % locates in the level -10 to 10 ℃/m; concrete with a relatively good heat exchange condition with the surrounding air has a narrower band distribution. In addition, the frequency distribution histogram should exclude the time zone from 00：00 to 06：00 because there is almost no traffic in this period. The amplitude of track slab temperature variation is obviously lower than that of the air temperature variation, and the former is approximately linear with the latter.展开更多
Purpose–The construction of cement asphalt(CA)emulsified mortar can obviously disturb the slab status after the fine adjustment.To decrease or eliminate the influence of CA mortar grouting on track slab geometry stat...Purpose–The construction of cement asphalt(CA)emulsified mortar can obviously disturb the slab status after the fine adjustment.To decrease or eliminate the influence of CA mortar grouting on track slab geometry status,the effects of grouting funnel,slab pressing method,mortar expansion ratio,seepage ratio and grouting area on China Railway Track System Type(CRTS I)track slab geometry status were discussed in this paper.Design/methodology/approach–Combined with engineering practice,this paper studied the expansion law of filling layer mortar,the liquid level height of the filling funnel,the pressure plate device and the amount of exudation water and systematically analyzed the influence of filling layer mortar construction on the state of track slab.Relevant precautions and countermeasures were put forward.Findings–The results showed that the track slab floating values of four corners were different with the CA mortar grouting and the track slab corner near CA mortar grouting hole had the maximum floating values.The anti-floating effect of“7”shaped slab pressing device was more efficient than fixed-joint angle iron,and the slab floating value could be further decreased by increasing the amount of“7”shaped slab pressing devices.After CA mortar grouting,the track slab floating pattern had a close correlation with the expansion rate and water seepage rate of CA mortar over time and the expansion and water seepage rate of the mortar were faster when the temperature was high.Furthermore,the use of strip CA mortar filling under the rail bearing platform on bothsides could effectively reduce the float under the track slab,and it could also save mortar consumption and reduce costs.Originality/value–This study plays an important role in controlling the floating values,CA mortar dosage and the building cost of projects by grouting CA mortar at two flanks of filling space.The research results have guiding significance for the design and construction of China’s CRTS I,CRTS II and CRTS III track slab.展开更多
Purpose–The precast concrete slab track(PST)has advantages of fewer maintenance frequencies,better smooth rides and structural stability,which has been widely applied in urban rail transit.Precise positioning of prec...Purpose–The precast concrete slab track(PST)has advantages of fewer maintenance frequencies,better smooth rides and structural stability,which has been widely applied in urban rail transit.Precise positioning of precast concrete slab(PCS)is vital for keeping the initial track regularity.However,the cast-in-place process of the self-compacting concrete(SCC)filling layer generally causes a large deformation of PCS due to the water-hammer effect of flowing SCC,even cracking of PCS.Currently,the buoyancy characteristic and influencing factors of PCS during the SCC casting process have not been thoroughly studied in urban rail transit.Design/methodology/approach–In this work,a Computational Fluid Dynamics(CFD)model is established to calculate the buoyancy of PCS caused by the flowing SCC.The main influencing factors,including the inlet speed and flowability of SCC,have been analyzed and discussed.A new structural optimization scheme has been proposed for PST to reduce the buoyancy caused by the flowing SCC.Findings–The simulation and field test results showed that the buoyancy and deformation of PCS decreased obviously after adopting the new scheme.Originality/value–The findings of this study can provide guidance for the control of the deformation of PCS during the SCC construction process.展开更多
When subjected to sustained high temperatures,the structure of the continuous China railway track system(CRTS)II railway track is susceptible to internal axial pressure,leading to joint damage and the potential for up...When subjected to sustained high temperatures,the structure of the continuous China railway track system(CRTS)II railway track is susceptible to internal axial pressure,leading to joint damage and the potential for upwarp buckling of the track slab.This study employs model testing to derive the upwarp buckling deformation curve of the track slab under conditions of joint damage.An analytical expression for the upwarp buckling equilibrium path of the track slab is derived through the application of the energy principle.Validation of the outcomes is performed by the comparison with experimental data.The effects of initial upwarp amplitude,initial upwarp curve type,elastic modulus,thickness,and gravity load on the upwarp buckling response of the track slab were investigated.The results show that:1)The upwarp deformation of the track slab in the narrow joint damage state is concentrated in a minor range on both sides of the joint,forming an inverted‘V’shape with concave ends.2)The joint damage can significantly reduce the upwarp buckling critical temperature rise of the track slab.3)The magnitude of the initial upwarp amplitude dictates the buckling mode of the track slab,while the initial upwarp curve predominantly influences the upwarp buckling critical temperature rise.Notably,an initial upwarp amplitude below 6.5 mm ensures the buckling resistance for up to a 60℃temperature rise.4)The increases in elastic modulus,gravity load,and track slab thickness can increase the upwarp buckling critical temperature rise.As the initial upwarp amplitude increases,the influence of these factors on the upwarp buckling critical temperature rise of the track slab gradually diminishes.展开更多
Arching and cracking of joints between slabs have become a problem in China Railway Track System(CRTS)II slab track.The slab track is susceptible to complex temperature variations as a longitudinal continuous structur...Arching and cracking of joints between slabs have become a problem in China Railway Track System(CRTS)II slab track.The slab track is susceptible to complex temperature variations as a longitudinal continuous structure.Based on measured data,a thermal-mechanical coupling model of the track was established.The deformation characteristics and interfacial damage behavior of joints under typical temperature fields were studied.The findings indicate that the annual extreme temperature range of the slab track,fluctuates from−1.4 to 49.8℃.The annual temperature gradient within the vertical depth range of 0 to 0.2 m of the track varies between−16.19℃/m and 30.15℃/m.The vertical deformation of joints is significantly influenced by high temperatures,with a maximum measured deformation of 0.828 mm.The joint seams are primarily affected by low temperatures,which lead to a separation of 0.9 to 1.0 mm.Conversely,interlayer damage of joints is predominantly influenced by elevated temperatures.In summer,the maximum ratio of interface damage area in the joint can reach up to 95%,with the maximum debonding area ratio can be as high as 84%.The research results can provide help for joint damage regularity and deformation control of CRTS II slab track.展开更多
Foamed concrete has been used to address the issue of differential settlement in high-speed railway subgrades in China.However,to enhance crack resistance,reinforcement is still necessary,and further research is requi...Foamed concrete has been used to address the issue of differential settlement in high-speed railway subgrades in China.However,to enhance crack resistance,reinforcement is still necessary,and further research is required to better understand the performance of foamed concrete in subgrade applications.To this end,a series of tests—including uniaxial compres-sive and dynamic triaxial tests—were conducted to comprehensively examine the effects of basalt fiber reinforcement on the mechanical properties of foamed concrete with densities of 700 and 1000 kg/m3.Additionally,a full-scale model of the foamed concrete subgrade was established,and simulated loading was applied.The diffusion patterns of dynamic stress and dynamic acceleration within the subgrade were explored,leading to the development of experimental formulas to calculate the attenuation coefficients of these two parameters along the depth and width of the subgrade.Furthermore,the dynamic displacement and cumulative settlement were analyzed to evaluate the stability of the subgrade.These findings provide valuable insights for the design and construction of foamed concrete subgrades in high-speed rail systems.The outcomes are currently under consideration for inclusion in the code of practice for high-speed rail restoration.展开更多
To address the issue of extreme thermal-induced arching in CRTS II slab tracks due to joint damage,an optimized joint repair model was proposed.First,the formula for calculating the safe temperature rise of the track ...To address the issue of extreme thermal-induced arching in CRTS II slab tracks due to joint damage,an optimized joint repair model was proposed.First,the formula for calculating the safe temperature rise of the track was derived based on the principle of stationary potential energy.Considering interlayer evolution and structural crack propagation,an optimized joint repair model for the track was established and validated.Subsequently,the impact of joint repair on track damage and arch stability under extreme temperatures was studied,and a comprehensive evaluation of the feasibility of joint repair and the evolution of damage after repair was conducted.The results show that after the joint repair,the temperature rise of the initial damage of the track structure can be increased by 11℃.Under the most unfavorable heating load with a superimposed temperature gradient,the maximum stiffness degradation index SDEG in the track structure is reduced by about 81.16%following joint repair.The joint repair process could effectively reduce the deformation of the slab arching under high temperatures,resulting in a reduction of 93.96%in upward arching deformation.After repair,with the damage to interfacing shear strength,the track arch increases by 2.616 mm.展开更多
In order to accommodate higher speeds,heavier axle weights,and vibration damping criteria,a new floating slab structure was proposed.The new type of floating slab track structure was composed of three prefabricated fl...In order to accommodate higher speeds,heavier axle weights,and vibration damping criteria,a new floating slab structure was proposed.The new type of floating slab track structure was composed of three prefabricated floating slabs longitudinally interconnected with magnesium ammonium phosphate concrete(MPC).This study investigated the dynamic performance of the structure.We constructd a full-scale indoor experimental model to scrutinize the disparities in the impact performance between a longitudinally connected floating slab track and its longitudinally disconnected counterpart.Additionally,a long-term fatigue experiment was conducted to assess the impact performance of longitudinally connected floating slab tracks under fatigue loading.The findings are described in the following.1)The new structure effectively suppresses ground vibrations,exhibiting a well-balanced energy distribution profile.However,the imposition of fatigue loading leads to a reduction in the damping performance of the steel spring damping system,thereby reducing its capacity to attenuate structural vibrations and leading to an increase in ground vibration energy;2)After 107 loading cycles,the attenuation rate of the vibration acceleration for the MPC increases by 171.9%.Conversely,at the corresponding disconnected location,the attenuation rate of ground vibration acceleration decreases by 65.6%.In conclusion,longitudinally connected floating slab tracks exhibit superior vibration reduction performance.While the vibration reduction performance of longitudinally connected floating slab tracks may diminish to some extent during long-term service,these tracks continue to meet specific vibration reduction requirements.展开更多
As one of the major high-speed railway ballastless track structures in China,CRTSIII slab ballastless track has been laid for more than 6500 km.However,there are no detailed studies on its track irregularity deteriora...As one of the major high-speed railway ballastless track structures in China,CRTSIII slab ballastless track has been laid for more than 6500 km.However,there are no detailed studies on its track irregularity deterioration throughout extended service periods,which may threaten the safety and stability of high-speed vehicles(HSV).In this study,a long-term tracking detection of CRTSIII slab ballastless track irregularities has been conducted,revealing its annual evolution law.An HSV-track coupled dynamics model was established to investigate the HSV dynamic responses under annual evolution of track irregularities.Considering the potential deterioration of track irregularities to extremely bad condition,the recommended classified limits for irregularity are proposed by analyzing the limit-exceeding probability of the safety and stability indexes of HSV.The results show that:taking 10 m wavelength as a demarcation,longer-wavelength irregularities exhibit larger amplitudes,faster evolution rates and a linear increasing trend,primarily affecting the stability of HSV.Conversely,shorter-wavelength irregularities exhibit smaller amplitudes and an insignificant evolution trend,predominantly affecting the safety of HSV.Furthermore,the periodic irregularity induced by the arching of 32 m simply-supported beam bridge should be paid closer attention to,as their evolution rate significantly surpasses that of irregularities at other wavelengths.展开更多
Considering the CRTS-II track slab,which is commonly used in the Chinese high-speed railway system,a vehicle-track-bridge dynamic analysis method is proposed in which the vehicle subsystem equations are established by...Considering the CRTS-II track slab,which is commonly used in the Chinese high-speed railway system,a vehicle-track-bridge dynamic analysis method is proposed in which the vehicle subsystem equations are established by the rigid body dynamics method,the track subsystem and the bridge subsystem equations are established by the FEM,the wheel-rail contact relation is defined by the corresponding assumption in vertical direction and the Kalker linear creep theory in lateral direction.The in-span spring element is derived to model the track-bridge interaction;the equal-band-width storage is adopted to fit the track structure with multilayer uniform section beam;and the dynamic equilibrium equations are solved by the inter-history iteration method.As a case study,the response of a CRH2 high-speed train transverses a simply-supported bridge with successive 31.5m double bound pre-stress beams is simulated.The result shows that using the vehicle-track-bridge interaction model instead of the vehicle-bridge interaction model helps predict the rotation angle at beam ends and choose an economic beam vertical stiffness.展开更多
The motor and trailer cars of a high-speed train were modeled as a multi-rigid body system with two suspensions. According to structural characteristic of a slab track, a new spatial vibration model of track segment e...The motor and trailer cars of a high-speed train were modeled as a multi-rigid body system with two suspensions. According to structural characteristic of a slab track, a new spatial vibration model of track segment element of the slab track was put forward. The spatial vibration equation set of the high-speed train and slab track system was then established on the basis of the principle of total potential energy with stationary value in elastic system dynamics and the rule of ＂set-in-right-position＂ for formulating system matrices. The equation set was solved by the Wilson-θ direct integration method. The contents mentioned above constitute the analysis theory of spatial vibration of high-speed train and slab track system. The theory was then verified by the high-speed running experiment carried out on the slab track in the Qinghuangdao-Shenyang passenger transport line. The results show that the calculated results agree well with the measured rcsults, such as the calculated lateral and vertical rail displacements are 0.82 mm and 0.9 mm and the measured ones 0.75 mm and 0.93 mm, respectively; the calculated lateral and vertical wheel-rail forces are 8.9 kN and 102.3 kN and the measured ones 8.6 kN and 80.2 kN, respectively. The interpolation method, that is, the lateral finite strip and slab segment element, for slab deformation proposed is of simplification and applicability compared with the traditional plate element method. All of these demonstrate the reliability of the theory proposed.展开更多
The dynamic responses of a slab track on transversely isotropic saturated soils subjected to moving train loads are investigated by a semi-analytical approach. The track model is described as an upper Euler beam to si...The dynamic responses of a slab track on transversely isotropic saturated soils subjected to moving train loads are investigated by a semi-analytical approach. The track model is described as an upper Euler beam to simulate the rails and a lower Euler beam to model the slab. Rail pads between the rails and slab are represented by a continuous layer of springs and dashpots. A series of point loads are formulated to describe the moving train loads. The governing equations of track-ground systems are solved using the double Fourier transform, and the dynamic responses in the time domain are obtained by the inverse Fourier transform. The results show that a train load with high velocity will generate a larger response in transversely isotropic saturated soil than the lower velocity load, and special attention should be paid on the pore pressure in the vicinity of the ground surface. The anisotropic parameters of a surface soil layer will have greater influence on the displacement and excess pore water pressure than those of the subsoil layer. The traditional design method taking ground soil as homogeneous isotropic soil is unsafe for the case of RE 〈 1 and RG 〈 1, so a transversely isotropic foundation model is of great significance to the design for high train velocities.展开更多
Low frequency vibrations induced by underground railways have attracted increasing attention in recent years. To obtain the characteristics of low frequency vibrations and the low frequency performance of a floating s...Low frequency vibrations induced by underground railways have attracted increasing attention in recent years. To obtain the characteristics of low frequency vibrations and the low frequency performance of a floating slab track (FST), low frequency vibration tests on an FST in an underground laboratory at Beijing Jiaotong University were carried out. The FST and an unbalanced shaker SBZ30 for dynamic simulation were designed for use in low frequency vibration experiments. Vibration measurements were performed on the bogie of the unbalanced shaker, the rail, the slab, the tunnel invert, the tunnel wall, the tunnel apex, and on the ground surface at distances varying from 0 to 80 m from the track. Measurements were also made on several floors of an adjacent building. Detailed results of low frequency vibration tests were reported. The attenuation of low frequency vibrations with the distance from the track was presented, as well as the responses of different floors of the building. The experimental results could be regarded as a reference for developing methods to control low frequency vibrations and for adopting countermeasures.展开更多
To improve the low-frequency vibration reduction effect of a steel spring floating slab track(FST),nonlinear quasizero-stiffness(QZS)vibration isolators composed of positive stiffness elements(PSEs)and negative stiffn...To improve the low-frequency vibration reduction effect of a steel spring floating slab track(FST),nonlinear quasizero-stiffness(QZS)vibration isolators composed of positive stiffness elements(PSEs)and negative stiffness elements(NSEs)were used to support the FST.First,considering the mechanical characteristics of the nonlinear QZS vibration isolators and the dynamic displacement limit(3 mm)of the FST,the feasible parameter groups were studied with the nonlinear stiffness variation range and bearing capacity as evaluation indices.A vertical vehicle quasi-zero-stiffness floating slab track(QZS-FST)coupled dynamic model was then established.To obtain a reasonable nonlinear stiffness within a few millimeters,the original length of the NSEs must be analyzed first,because it chiefly determines the stiffness nonlinearity level.The compression length of the NSEs at the equilibrium position must be determined to obtain the low stiffness of the floating slab without vehicle load.Meanwhile,to meet the dynamic displacement limit of the FST,the PSE stiffness must be increased to obtain a higher stiffness at the critical dynamic displacement.Various stiffness groups for the PSEs and NSEs can provide the same dynamic bearing capacity and yet have a significantly different vibration reduction effect.Excessive stiffness nonlinearity levels cannot effectively improve the vibration reduction effect at the natural frequency.Furthermore,they also significantly amplify the vibrations above the natural frequency.In this paper,the vertical vibration acceleration level(VAL)of the floating slab and the supporting force of the FST can be decreased by 6.9 dB and 55%,respectively,at the resonance frequency.展开更多
Subgrade frost heave in seasonally frozen ground can greatly influence the safety and smooth running of high-speed trains and the service performance of track structures.In this study,we used a static model to:(1)inve...Subgrade frost heave in seasonally frozen ground can greatly influence the safety and smooth running of high-speed trains and the service performance of track structures.In this study,we used a static model to:(1)investigate track-subgrade frost heave and develop a dynamic model of vehicle-track-subgrade frost heave;(2)explore the transfer relation between subgrade frost heave and track structure deformation;(3)examine the characteristics of interlayer debonding;(4)study the influence of subgrade frost heave on the dynamic response of vehicles in high-speed railways in seasonally frozen regions.A Fourier series was used to fit the frost heave waveform and simulate the behavior of subgrade uneven frost heave using data collected on-site.The results show:(i)The position of frost heave significantly affects the transfer of deformation to a slab track.The largest deformation of the track slab,with the amplitude transfer ratio reaching 20%,was recorded when the frost heave occurred near the joint of the base plate.(ii)At the same frost heave amplitude,long-wave frost heave causes smaller deformation and debonding of the track structure than short-wave frost heave.In the wavelength range of 10-30 m,the main frequency of the acceleration spectral density was concentrated between 3.5 and 3.7 Hz,with larger frost heave wavelengths producing smaller superposition on the vertical acceleration of the vehicle.(ii)The maximum wheel-rail force occurs when the front bogie passes the frost heave peak,with greater frost heave amplitudes producing greater wheel-rail force.From these results,we conclude there is a clear need to control the frost heave deformation of the track to reduce the dynamic response of the vehicle and in turn improve train operatSubgrade frost heave in seasonally frozen ground can greatly influence the safety and smooth running of high-speed trains and the service performance of track structures.In this study,we used a static model to:(1)investigate track`-subgrade frost heave and develop a dynamic model of vehicle`-track`-subgrade frost heave;(2)explore the transfer relation between subgrade frost heave and track structure deformation;(3)examine the characteristics of interlayer debonding;(4)study the influence of subgrade frost heave on the dynamic response of vehicles in high-speed railways in seasonally frozen regions.A Fourier series was used to fit the frost heave waveform and simulate the behavior of subgrade uneven frost heave using data collected on-site.The results show:(i)The position of frost heave significantly affects the transfer of deformation to a slab track.The largest deformation of the track slab,with the amplitude transfer ratio reaching 20%,was recorded when the frost heave occurred near the joint of the base plate.(ii)At the same frost heave amplitude,long-wave frost heave causes smaller deformation and debonding of the track structure than short-wave frost heave.In the wavelength range of 10-30 m,the main frequency of the acceleration spectral density was concentrated between 3.5 and 3.7 Hz,with larger frost heave wavelengths producing smaller superposition on the vertical acceleration of the vehicle.(iii)The maximum wheel`-rail force occurs when the front bogie passes the frost heave peak,with greater frost heave amplitudes producing greater wheel`-rail force.From these results,we conclude there is a clear need to control the frost heave deformation of the track to reduce the dynamic response of the vehicle and in turn improve train operations.ions.展开更多
Under repeated train-induced loads, cement and emulsified asphalt mortar(CA mortar) as a viscoelastic material has a time-dependent deformation, part of which is irreversible. This could lead to debonding between the ...Under repeated train-induced loads, cement and emulsified asphalt mortar(CA mortar) as a viscoelastic material has a time-dependent deformation, part of which is irreversible. This could lead to debonding between the mortar layer and the track slab. Based on the theory of viscoelasticity and the analytical method of the time hardening law(THL), the viscoelastic deformation behavior of CA mortar was studied. Using ABAQUS, we established a solid model of China railway track system(CRTS) Ⅰ prefabricated slab track, with CA mortar at different initial Young’s moduli under cyclic loading corresponding to the influence of actual train loads. The results reveal that the fitted parameters of the THL for CA mortar are suitable for describing its viscoelastic deformation. As the initial Young’s modulus increases, the strain difference before and after cyclic loading gradually decreases, and the displacement difference increases from 0.2 mm to 0.6 mm. The deformation mainly occurs at the end of a mortar layer with longitudinal distribution of about 2.5 times the fasteners’ spacing. It follows that the viscoelastic performance of CA mortar is one of the most important reasons that cause debonding underneath the track slab. Therefore, we suggest that the adverse effects of viscoelastic behavior of CA mortar should be considered when researching such deformation and damage.展开更多
The dynamic behaviour of slab and ballast tracks was investigated using measurements and calculations.Hammer impacts and train passages were analysed and measurements were made using geophones(velocity transducers)whi...The dynamic behaviour of slab and ballast tracks was investigated using measurements and calculations.Hammer impacts and train passages were analysed and measurements were made using geophones(velocity transducers)which had been time-integrated to displacements.The calculations were carried out in the frequency-wavenumber domain for multi-beamon-continuous soil models.The characteristics of the different tracks and track elements were established in theory and by experiment.The frequency-dependent compliances(displacement transfer functions)showed clear rail-on-railpad resonances or highly damped track-soil resonances.Compared to the rail and sleeper,the track slab had much lower amplitudes.The slab track usually had the highest rail amplitudes due to soft railpads.Train passage yielded track displacements which were a superposition of the axle loads from the two neighbouring axles of a bogie and from the two bogies of two neighbouring carriages.This global behaviour was characteristic of the track slab of the slab track,whereas the rails of the slab and the ballast tracks behaved more locally with only one bogie of influence.The measurements agreed very well with the theory of continuous soil in the case of the six measured slab tracks and acceptably well for the six measured ballast tracks.The measurements allowed us to find appropriate model parameters and to check the models.For example,the Winkler model of the soil was found to be less appropriate because it reacted more locally.展开更多
To accurately identify the potential contact loss of the China railway track system(CRTS)III prefabricated slab track,a finite element model with contact loss of self-compacting concrete(SCC)under transient impact was...To accurately identify the potential contact loss of the China railway track system(CRTS)III prefabricated slab track,a finite element model with contact loss of self-compacting concrete(SCC)under transient impact was established.Then the vertical accelerations near impact points on the track slab surface were extracted to obtain damage-sensitive indices in the time and frequency domains.The indices were initially normalized to obtain independent items of evidence before the Dempster-Shafer(D-S)evidence theory was used to fuse these into one.Finally,a two-stage identification was performed to identify the damaged SCC area,comprising a rough identification(Stage I)and a precise identification(Stage II).The research results show that the damage indices extracted based on the transient impact response change abruptly at the damage location,and that can be used for damage identification.However,the use of a single index to determine the damage of the impact point may be misjudged.In Stage I,five damage indices of acceleration were fused to magnify the difference between the damaged point and undamaged point,thereby improving the accuracy of finding damage.In Stage II,in the area where more impact points were added,a fusion of three indices of acceleration response,that is,the absolute mean of the time domain,the maximum amplitude of the frequency domain,and the power density ratio,further narrowed down the area where damage exists.As a result,when the contact loss of SCC is greater than 50%along the thickness direction,the identification accuracy can be as high as 70%to 80%.The two-stage identification method proposed in this study can greatly improve the efficiency of interlayer damage detection of slab tracks and is expected to provide effective technical support for damage identification of track structures in the future.展开更多
The interface of slab track laid in cold regions is prone to debonding under the coupling of freeze-thaw cyclesand temperature loads.Based on the composite specimen tests,the parameters of cohesive zone model were obt...The interface of slab track laid in cold regions is prone to debonding under the coupling of freeze-thaw cyclesand temperature loads.Based on the composite specimen tests,the parameters of cohesive zone model were obtained andused in a simulation model of CRTS III prefabricated slab track to study the interlayer damage.The results show that 1)the digital image correlation(DIC)technique can accurately capture the strain field changes on the interface of compositespecimens under splitting and shear loading;2)when the temperature gradient is−40℃/m−60℃/m,the interfacedamage of the slab track is minimal and presents different patterns of expansion under positive and negative temperaturegradients,each corresponding to damage of the cohesive element dominated by shear stress and normal tensile stress,respectively;3)the reduction of the elastic modulus at the concrete base after freeze-thaw inhibits interface damage andleads to a higher starting temperature gradient load,but cracking can occur on the concrete base after 150 freeze-thaws.For this reason,in the light of damage control of both the interface and concrete base,the elastic modulus of the concretebase is 54%or over that without freeze-thaw cycles.展开更多
Purpose-Temperature is an important load for a ballastless track.However,little research has been conducted on the dynamic responses when a train travels on a ballastless track under the temperature gradient.The dynam...Purpose-Temperature is an important load for a ballastless track.However,little research has been conducted on the dynamic responses when a train travels on a ballastless track under the temperature gradient.The dynamic responses under different temperature gradients of the slab are theoretically investigated in this work.Design/methodology/approach-Considering the moving train,the temperature gradient of the slab,and the gravity of the slab track,a dynamic model for a high-speed train that runs along the CRTS Ⅲ slab track on subgrade is developed by a nonlinear coupled way in Abaqus.Findings-The results are as follows:(1)The upward transmission of the periodic deformation of the slab causes periodic track irregularity.(2)Because of the geometric constraint of limiting structures,the maximum bending stresses of the slab occur near the end of the slab under positive temperature gradients,but in the middle of the slab under negative temperature gradients.(3)The periodic deformation of the slab can induce periodic changes in the interlayer stiffness and contact status,leading to a large vibration of the slab.Because of the vibration-reduction capacity of the fastener and the larger mass of the concrete base,the accelerations of both the slab and concrete base are far less than the acceleration of the rail.Originality/value-This study reveals the influence mechanism of temperature gradient-induced periodic deformation in the dynamic responses of the train-track system,and it also provides a guide for the safe service of CRTS Ⅲ slab track.展开更多
基金supported by the National Key Basic Research Program of China (973 Program) (2013CB036202)the National Natural Science Foundation of China (51008258)Fundamental Research Funds for the Central Universities (SWJTU12CX065)
文摘Temperature is one of the important loads for designing slab track. The characteristic of slab track tem- perature varies greatly with different regional climates. In this work, a bi-block slab track model was built under outdoor conditions in Chengdu area; the statistical characteristic of temperature gradient in track slab and the relationship between temperature gradient and surface air temperature were tested and analyzed. The results show that the track slab temperature gradient will vary periodically according to the surface air temperature, and show a clear nonlinearity along the height direction. The temperature gradient distribution is extremely uneven： the temperature gradient in the top part of the track slab is larger than that in the bottom part; the most frequently occurring temperature gradient of the track slab is around -3.5 ℃/m and more than 75 % locates in the level -10 to 10 ℃/m; concrete with a relatively good heat exchange condition with the surrounding air has a narrower band distribution. In addition, the frequency distribution histogram should exclude the time zone from 00：00 to 06：00 because there is almost no traffic in this period. The amplitude of track slab temperature variation is obviously lower than that of the air temperature variation, and the former is approximately linear with the latter.
基金funded by the National Natural Science Foundation of China(No.51408610).
文摘Purpose–The construction of cement asphalt(CA)emulsified mortar can obviously disturb the slab status after the fine adjustment.To decrease or eliminate the influence of CA mortar grouting on track slab geometry status,the effects of grouting funnel,slab pressing method,mortar expansion ratio,seepage ratio and grouting area on China Railway Track System Type(CRTS I)track slab geometry status were discussed in this paper.Design/methodology/approach–Combined with engineering practice,this paper studied the expansion law of filling layer mortar,the liquid level height of the filling funnel,the pressure plate device and the amount of exudation water and systematically analyzed the influence of filling layer mortar construction on the state of track slab.Relevant precautions and countermeasures were put forward.Findings–The results showed that the track slab floating values of four corners were different with the CA mortar grouting and the track slab corner near CA mortar grouting hole had the maximum floating values.The anti-floating effect of“7”shaped slab pressing device was more efficient than fixed-joint angle iron,and the slab floating value could be further decreased by increasing the amount of“7”shaped slab pressing devices.After CA mortar grouting,the track slab floating pattern had a close correlation with the expansion rate and water seepage rate of CA mortar over time and the expansion and water seepage rate of the mortar were faster when the temperature was high.Furthermore,the use of strip CA mortar filling under the rail bearing platform on bothsides could effectively reduce the float under the track slab,and it could also save mortar consumption and reduce costs.Originality/value–This study plays an important role in controlling the floating values,CA mortar dosage and the building cost of projects by grouting CA mortar at two flanks of filling space.The research results have guiding significance for the design and construction of China’s CRTS I,CRTS II and CRTS III track slab.
文摘Purpose–The precast concrete slab track(PST)has advantages of fewer maintenance frequencies,better smooth rides and structural stability,which has been widely applied in urban rail transit.Precise positioning of precast concrete slab(PCS)is vital for keeping the initial track regularity.However,the cast-in-place process of the self-compacting concrete(SCC)filling layer generally causes a large deformation of PCS due to the water-hammer effect of flowing SCC,even cracking of PCS.Currently,the buoyancy characteristic and influencing factors of PCS during the SCC casting process have not been thoroughly studied in urban rail transit.Design/methodology/approach–In this work,a Computational Fluid Dynamics(CFD)model is established to calculate the buoyancy of PCS caused by the flowing SCC.The main influencing factors,including the inlet speed and flowability of SCC,have been analyzed and discussed.A new structural optimization scheme has been proposed for PST to reduce the buoyancy caused by the flowing SCC.Findings–The simulation and field test results showed that the buoyancy and deformation of PCS decreased obviously after adopting the new scheme.Originality/value–The findings of this study can provide guidance for the control of the deformation of PCS during the SCC construction process.
基金supported by the National Natural Science Foundation of China(No.52278459).
文摘When subjected to sustained high temperatures,the structure of the continuous China railway track system(CRTS)II railway track is susceptible to internal axial pressure,leading to joint damage and the potential for upwarp buckling of the track slab.This study employs model testing to derive the upwarp buckling deformation curve of the track slab under conditions of joint damage.An analytical expression for the upwarp buckling equilibrium path of the track slab is derived through the application of the energy principle.Validation of the outcomes is performed by the comparison with experimental data.The effects of initial upwarp amplitude,initial upwarp curve type,elastic modulus,thickness,and gravity load on the upwarp buckling response of the track slab were investigated.The results show that:1)The upwarp deformation of the track slab in the narrow joint damage state is concentrated in a minor range on both sides of the joint,forming an inverted‘V’shape with concave ends.2)The joint damage can significantly reduce the upwarp buckling critical temperature rise of the track slab.3)The magnitude of the initial upwarp amplitude dictates the buckling mode of the track slab,while the initial upwarp curve predominantly influences the upwarp buckling critical temperature rise.Notably,an initial upwarp amplitude below 6.5 mm ensures the buckling resistance for up to a 60℃temperature rise.4)The increases in elastic modulus,gravity load,and track slab thickness can increase the upwarp buckling critical temperature rise.As the initial upwarp amplitude increases,the influence of these factors on the upwarp buckling critical temperature rise of the track slab gradually diminishes.
基金Projects(U23A20666,52178405)supported by the National Natural Science Foundation of ChinaProject(K2022G038)supported by the Science and Technology Research and Development Program of China State Railway Group Co.,Ltd.Project(2021B03)supported by the Science and Technology Plan of Shandong Provincial Department of Transportation,China。
文摘Arching and cracking of joints between slabs have become a problem in China Railway Track System(CRTS)II slab track.The slab track is susceptible to complex temperature variations as a longitudinal continuous structure.Based on measured data,a thermal-mechanical coupling model of the track was established.The deformation characteristics and interfacial damage behavior of joints under typical temperature fields were studied.The findings indicate that the annual extreme temperature range of the slab track,fluctuates from−1.4 to 49.8℃.The annual temperature gradient within the vertical depth range of 0 to 0.2 m of the track varies between−16.19℃/m and 30.15℃/m.The vertical deformation of joints is significantly influenced by high temperatures,with a maximum measured deformation of 0.828 mm.The joint seams are primarily affected by low temperatures,which lead to a separation of 0.9 to 1.0 mm.Conversely,interlayer damage of joints is predominantly influenced by elevated temperatures.In summer,the maximum ratio of interface damage area in the joint can reach up to 95%,with the maximum debonding area ratio can be as high as 84%.The research results can provide help for joint damage regularity and deformation control of CRTS II slab track.
基金support for this research from the Fundamental Research Funds for the National Natural Science Foundation of China (Grant Nos. 51978588, 52078434, and 52368065)the China Scholarship Council (Grant No. 202107000077)UKRI Engineering and Physical Science ResearchCouncil (EPSRC) for the financial sponsorship of Re4Rail project (Grant No. EP/Y015401/1)
文摘Foamed concrete has been used to address the issue of differential settlement in high-speed railway subgrades in China.However,to enhance crack resistance,reinforcement is still necessary,and further research is required to better understand the performance of foamed concrete in subgrade applications.To this end,a series of tests—including uniaxial compres-sive and dynamic triaxial tests—were conducted to comprehensively examine the effects of basalt fiber reinforcement on the mechanical properties of foamed concrete with densities of 700 and 1000 kg/m3.Additionally,a full-scale model of the foamed concrete subgrade was established,and simulated loading was applied.The diffusion patterns of dynamic stress and dynamic acceleration within the subgrade were explored,leading to the development of experimental formulas to calculate the attenuation coefficients of these two parameters along the depth and width of the subgrade.Furthermore,the dynamic displacement and cumulative settlement were analyzed to evaluate the stability of the subgrade.These findings provide valuable insights for the design and construction of foamed concrete subgrades in high-speed rail systems.The outcomes are currently under consideration for inclusion in the code of practice for high-speed rail restoration.
基金Project(K2022G038)supported by the Science Technology Research and Development Program of China State Railway Group Co.,LtdProject(52178405)supported by the National Natural Science Foundation of China。
文摘To address the issue of extreme thermal-induced arching in CRTS II slab tracks due to joint damage,an optimized joint repair model was proposed.First,the formula for calculating the safe temperature rise of the track was derived based on the principle of stationary potential energy.Considering interlayer evolution and structural crack propagation,an optimized joint repair model for the track was established and validated.Subsequently,the impact of joint repair on track damage and arch stability under extreme temperatures was studied,and a comprehensive evaluation of the feasibility of joint repair and the evolution of damage after repair was conducted.The results show that after the joint repair,the temperature rise of the initial damage of the track structure can be increased by 11℃.Under the most unfavorable heating load with a superimposed temperature gradient,the maximum stiffness degradation index SDEG in the track structure is reduced by about 81.16%following joint repair.The joint repair process could effectively reduce the deformation of the slab arching under high temperatures,resulting in a reduction of 93.96%in upward arching deformation.After repair,with the damage to interfacing shear strength,the track arch increases by 2.616 mm.
基金Project(2022-Major-14)supported by the Science and Technology Research and Development Program Project of China Railway Group Limited。
文摘In order to accommodate higher speeds,heavier axle weights,and vibration damping criteria,a new floating slab structure was proposed.The new type of floating slab track structure was composed of three prefabricated floating slabs longitudinally interconnected with magnesium ammonium phosphate concrete(MPC).This study investigated the dynamic performance of the structure.We constructd a full-scale indoor experimental model to scrutinize the disparities in the impact performance between a longitudinally connected floating slab track and its longitudinally disconnected counterpart.Additionally,a long-term fatigue experiment was conducted to assess the impact performance of longitudinally connected floating slab tracks under fatigue loading.The findings are described in the following.1)The new structure effectively suppresses ground vibrations,exhibiting a well-balanced energy distribution profile.However,the imposition of fatigue loading leads to a reduction in the damping performance of the steel spring damping system,thereby reducing its capacity to attenuate structural vibrations and leading to an increase in ground vibration energy;2)After 107 loading cycles,the attenuation rate of the vibration acceleration for the MPC increases by 171.9%.Conversely,at the corresponding disconnected location,the attenuation rate of ground vibration acceleration decreases by 65.6%.In conclusion,longitudinally connected floating slab tracks exhibit superior vibration reduction performance.While the vibration reduction performance of longitudinally connected floating slab tracks may diminish to some extent during long-term service,these tracks continue to meet specific vibration reduction requirements.
基金Project(2022YFB2602900)supported by the National Key Research and Development Program of ChinaProject(K2022T002)supported by the Scientific Research Plan of China Railway。
文摘As one of the major high-speed railway ballastless track structures in China,CRTSIII slab ballastless track has been laid for more than 6500 km.However,there are no detailed studies on its track irregularity deterioration throughout extended service periods,which may threaten the safety and stability of high-speed vehicles(HSV).In this study,a long-term tracking detection of CRTSIII slab ballastless track irregularities has been conducted,revealing its annual evolution law.An HSV-track coupled dynamics model was established to investigate the HSV dynamic responses under annual evolution of track irregularities.Considering the potential deterioration of track irregularities to extremely bad condition,the recommended classified limits for irregularity are proposed by analyzing the limit-exceeding probability of the safety and stability indexes of HSV.The results show that:taking 10 m wavelength as a demarcation,longer-wavelength irregularities exhibit larger amplitudes,faster evolution rates and a linear increasing trend,primarily affecting the stability of HSV.Conversely,shorter-wavelength irregularities exhibit smaller amplitudes and an insignificant evolution trend,predominantly affecting the safety of HSV.Furthermore,the periodic irregularity induced by the arching of 32 m simply-supported beam bridge should be paid closer attention to,as their evolution rate significantly surpasses that of irregularities at other wavelengths.
基金supported by the National Basic Research Program of China("973"Project)(Grant No.2013CB036203)the National Natural Science Foundation of China(Grant No.U1134206)+1 种基金the 111 project(Grant No.B13002)the Doctoral Fund of Ministry of Education of China(Grant No.20130009110036)
文摘Considering the CRTS-II track slab,which is commonly used in the Chinese high-speed railway system,a vehicle-track-bridge dynamic analysis method is proposed in which the vehicle subsystem equations are established by the rigid body dynamics method,the track subsystem and the bridge subsystem equations are established by the FEM,the wheel-rail contact relation is defined by the corresponding assumption in vertical direction and the Kalker linear creep theory in lateral direction.The in-span spring element is derived to model the track-bridge interaction;the equal-band-width storage is adopted to fit the track structure with multilayer uniform section beam;and the dynamic equilibrium equations are solved by the inter-history iteration method.As a case study,the response of a CRH2 high-speed train transverses a simply-supported bridge with successive 31.5m double bound pre-stress beams is simulated.The result shows that using the vehicle-track-bridge interaction model instead of the vehicle-bridge interaction model helps predict the rotation angle at beam ends and choose an economic beam vertical stiffness.
基金Project(2007CB714706) supported by the National Basic Research Program of ChinaProject (50678176) supported by the National Natural Science Foundation of ChinaProject(NCET-07-0866) supported by the Program for New Century Excellent Talents in University
文摘The motor and trailer cars of a high-speed train were modeled as a multi-rigid body system with two suspensions. According to structural characteristic of a slab track, a new spatial vibration model of track segment element of the slab track was put forward. The spatial vibration equation set of the high-speed train and slab track system was then established on the basis of the principle of total potential energy with stationary value in elastic system dynamics and the rule of ＂set-in-right-position＂ for formulating system matrices. The equation set was solved by the Wilson-θ direct integration method. The contents mentioned above constitute the analysis theory of spatial vibration of high-speed train and slab track system. The theory was then verified by the high-speed running experiment carried out on the slab track in the Qinghuangdao-Shenyang passenger transport line. The results show that the calculated results agree well with the measured rcsults, such as the calculated lateral and vertical rail displacements are 0.82 mm and 0.9 mm and the measured ones 0.75 mm and 0.93 mm, respectively; the calculated lateral and vertical wheel-rail forces are 8.9 kN and 102.3 kN and the measured ones 8.6 kN and 80.2 kN, respectively. The interpolation method, that is, the lateral finite strip and slab segment element, for slab deformation proposed is of simplification and applicability compared with the traditional plate element method. All of these demonstrate the reliability of the theory proposed.
基金the National Basic Research Program of China under Grant No.2013CB036405the Key Research Program of the Chinese Academy of Sciences under Grant No.KZZD-EW-05the Natural Science Foundation of China under Grant Nos.41402317,51209201 and 51279198
文摘The dynamic responses of a slab track on transversely isotropic saturated soils subjected to moving train loads are investigated by a semi-analytical approach. The track model is described as an upper Euler beam to simulate the rails and a lower Euler beam to model the slab. Rail pads between the rails and slab are represented by a continuous layer of springs and dashpots. A series of point loads are formulated to describe the moving train loads. The governing equations of track-ground systems are solved using the double Fourier transform, and the dynamic responses in the time domain are obtained by the inverse Fourier transform. The results show that a train load with high velocity will generate a larger response in transversely isotropic saturated soil than the lower velocity load, and special attention should be paid on the pore pressure in the vicinity of the ground surface. The anisotropic parameters of a surface soil layer will have greater influence on the displacement and excess pore water pressure than those of the subsoil layer. The traditional design method taking ground soil as homogeneous isotropic soil is unsafe for the case of RE 〈 1 and RG 〈 1, so a transversely isotropic foundation model is of great significance to the design for high train velocities.
基金Project supported by the National Natural Science Foundation of China (No. 51008017)the Fundamental Research Funds for the Central Universities of China (Nos. 2009JBM074 and 2009JBM075)
文摘Low frequency vibrations induced by underground railways have attracted increasing attention in recent years. To obtain the characteristics of low frequency vibrations and the low frequency performance of a floating slab track (FST), low frequency vibration tests on an FST in an underground laboratory at Beijing Jiaotong University were carried out. The FST and an unbalanced shaker SBZ30 for dynamic simulation were designed for use in low frequency vibration experiments. Vibration measurements were performed on the bogie of the unbalanced shaker, the rail, the slab, the tunnel invert, the tunnel wall, the tunnel apex, and on the ground surface at distances varying from 0 to 80 m from the track. Measurements were also made on several floors of an adjacent building. Detailed results of low frequency vibration tests were reported. The attenuation of low frequency vibrations with the distance from the track was presented, as well as the responses of different floors of the building. The experimental results could be regarded as a reference for developing methods to control low frequency vibrations and for adopting countermeasures.
基金Project supported by the National Natural Science Foundation of China(Nos.5197858351425804+2 种基金51578468and 51608460)the Open Foundation of State Key Laboratory for Track Technology of High-speed Railway(No.2018YJ180)。
文摘To improve the low-frequency vibration reduction effect of a steel spring floating slab track(FST),nonlinear quasizero-stiffness(QZS)vibration isolators composed of positive stiffness elements(PSEs)and negative stiffness elements(NSEs)were used to support the FST.First,considering the mechanical characteristics of the nonlinear QZS vibration isolators and the dynamic displacement limit(3 mm)of the FST,the feasible parameter groups were studied with the nonlinear stiffness variation range and bearing capacity as evaluation indices.A vertical vehicle quasi-zero-stiffness floating slab track(QZS-FST)coupled dynamic model was then established.To obtain a reasonable nonlinear stiffness within a few millimeters,the original length of the NSEs must be analyzed first,because it chiefly determines the stiffness nonlinearity level.The compression length of the NSEs at the equilibrium position must be determined to obtain the low stiffness of the floating slab without vehicle load.Meanwhile,to meet the dynamic displacement limit of the FST,the PSE stiffness must be increased to obtain a higher stiffness at the critical dynamic displacement.Various stiffness groups for the PSEs and NSEs can provide the same dynamic bearing capacity and yet have a significantly different vibration reduction effect.Excessive stiffness nonlinearity levels cannot effectively improve the vibration reduction effect at the natural frequency.Furthermore,they also significantly amplify the vibrations above the natural frequency.In this paper,the vertical vibration acceleration level(VAL)of the floating slab and the supporting force of the FST can be decreased by 6.9 dB and 55%,respectively,at the resonance frequency.
基金This work is supported by the National Key R&D Program of China(No.2021YFF0502100)the National Natural Science Foundation of China(Nos.52022085 and 52278461)+1 种基金the Sichuan Provincial Youth Science and Technology Innovation Team(No.2022JDTD0015)the Research and Development Program of China State Railway Group Co.,Ltd.(No.N2022G033),China.
文摘Subgrade frost heave in seasonally frozen ground can greatly influence the safety and smooth running of high-speed trains and the service performance of track structures.In this study,we used a static model to:(1)investigate track-subgrade frost heave and develop a dynamic model of vehicle-track-subgrade frost heave;(2)explore the transfer relation between subgrade frost heave and track structure deformation;(3)examine the characteristics of interlayer debonding;(4)study the influence of subgrade frost heave on the dynamic response of vehicles in high-speed railways in seasonally frozen regions.A Fourier series was used to fit the frost heave waveform and simulate the behavior of subgrade uneven frost heave using data collected on-site.The results show:(i)The position of frost heave significantly affects the transfer of deformation to a slab track.The largest deformation of the track slab,with the amplitude transfer ratio reaching 20%,was recorded when the frost heave occurred near the joint of the base plate.(ii)At the same frost heave amplitude,long-wave frost heave causes smaller deformation and debonding of the track structure than short-wave frost heave.In the wavelength range of 10-30 m,the main frequency of the acceleration spectral density was concentrated between 3.5 and 3.7 Hz,with larger frost heave wavelengths producing smaller superposition on the vertical acceleration of the vehicle.(ii)The maximum wheel-rail force occurs when the front bogie passes the frost heave peak,with greater frost heave amplitudes producing greater wheel-rail force.From these results,we conclude there is a clear need to control the frost heave deformation of the track to reduce the dynamic response of the vehicle and in turn improve train operatSubgrade frost heave in seasonally frozen ground can greatly influence the safety and smooth running of high-speed trains and the service performance of track structures.In this study,we used a static model to:(1)investigate track`-subgrade frost heave and develop a dynamic model of vehicle`-track`-subgrade frost heave;(2)explore the transfer relation between subgrade frost heave and track structure deformation;(3)examine the characteristics of interlayer debonding;(4)study the influence of subgrade frost heave on the dynamic response of vehicles in high-speed railways in seasonally frozen regions.A Fourier series was used to fit the frost heave waveform and simulate the behavior of subgrade uneven frost heave using data collected on-site.The results show:(i)The position of frost heave significantly affects the transfer of deformation to a slab track.The largest deformation of the track slab,with the amplitude transfer ratio reaching 20%,was recorded when the frost heave occurred near the joint of the base plate.(ii)At the same frost heave amplitude,long-wave frost heave causes smaller deformation and debonding of the track structure than short-wave frost heave.In the wavelength range of 10-30 m,the main frequency of the acceleration spectral density was concentrated between 3.5 and 3.7 Hz,with larger frost heave wavelengths producing smaller superposition on the vertical acceleration of the vehicle.(iii)The maximum wheel`-rail force occurs when the front bogie passes the frost heave peak,with greater frost heave amplitudes producing greater wheel`-rail force.From these results,we conclude there is a clear need to control the frost heave deformation of the track to reduce the dynamic response of the vehicle and in turn improve train operations.ions.
基金Project supported by the National Natural Science Foundation of China(No.51578472)。
文摘Under repeated train-induced loads, cement and emulsified asphalt mortar(CA mortar) as a viscoelastic material has a time-dependent deformation, part of which is irreversible. This could lead to debonding between the mortar layer and the track slab. Based on the theory of viscoelasticity and the analytical method of the time hardening law(THL), the viscoelastic deformation behavior of CA mortar was studied. Using ABAQUS, we established a solid model of China railway track system(CRTS) Ⅰ prefabricated slab track, with CA mortar at different initial Young’s moduli under cyclic loading corresponding to the influence of actual train loads. The results reveal that the fitted parameters of the THL for CA mortar are suitable for describing its viscoelastic deformation. As the initial Young’s modulus increases, the strain difference before and after cyclic loading gradually decreases, and the displacement difference increases from 0.2 mm to 0.6 mm. The deformation mainly occurs at the end of a mortar layer with longitudinal distribution of about 2.5 times the fasteners’ spacing. It follows that the viscoelastic performance of CA mortar is one of the most important reasons that cause debonding underneath the track slab. Therefore, we suggest that the adverse effects of viscoelastic behavior of CA mortar should be considered when researching such deformation and damage.
文摘The dynamic behaviour of slab and ballast tracks was investigated using measurements and calculations.Hammer impacts and train passages were analysed and measurements were made using geophones(velocity transducers)which had been time-integrated to displacements.The calculations were carried out in the frequency-wavenumber domain for multi-beamon-continuous soil models.The characteristics of the different tracks and track elements were established in theory and by experiment.The frequency-dependent compliances(displacement transfer functions)showed clear rail-on-railpad resonances or highly damped track-soil resonances.Compared to the rail and sleeper,the track slab had much lower amplitudes.The slab track usually had the highest rail amplitudes due to soft railpads.Train passage yielded track displacements which were a superposition of the axle loads from the two neighbouring axles of a bogie and from the two bogies of two neighbouring carriages.This global behaviour was characteristic of the track slab of the slab track,whereas the rails of the slab and the ballast tracks behaved more locally with only one bogie of influence.The measurements agreed very well with the theory of continuous soil in the case of the six measured slab tracks and acceptably well for the six measured ballast tracks.The measurements allowed us to find appropriate model parameters and to check the models.For example,the Winkler model of the soil was found to be less appropriate because it reacted more locally.
基金This work is supported by the National Key R&D Program of China(Nos.2021YFF0502100 and 2021YFB2600900)the National Natural Science Foundation of China(Nos.52022085 and 52278461)the Sichuan Provincial Youth Science and Technology Innovation Team(No.2022JDTD0015),China.
文摘To accurately identify the potential contact loss of the China railway track system(CRTS)III prefabricated slab track,a finite element model with contact loss of self-compacting concrete(SCC)under transient impact was established.Then the vertical accelerations near impact points on the track slab surface were extracted to obtain damage-sensitive indices in the time and frequency domains.The indices were initially normalized to obtain independent items of evidence before the Dempster-Shafer(D-S)evidence theory was used to fuse these into one.Finally,a two-stage identification was performed to identify the damaged SCC area,comprising a rough identification(Stage I)and a precise identification(Stage II).The research results show that the damage indices extracted based on the transient impact response change abruptly at the damage location,and that can be used for damage identification.However,the use of a single index to determine the damage of the impact point may be misjudged.In Stage I,five damage indices of acceleration were fused to magnify the difference between the damaged point and undamaged point,thereby improving the accuracy of finding damage.In Stage II,in the area where more impact points were added,a fusion of three indices of acceleration response,that is,the absolute mean of the time domain,the maximum amplitude of the frequency domain,and the power density ratio,further narrowed down the area where damage exists.As a result,when the contact loss of SCC is greater than 50%along the thickness direction,the identification accuracy can be as high as 70%to 80%.The two-stage identification method proposed in this study can greatly improve the efficiency of interlayer damage detection of slab tracks and is expected to provide effective technical support for damage identification of track structures in the future.
基金Project(52425213)supported by the National Science Fund for Distinguished Young Scholars of ChinaProjects(52278461,52308467)supported by the National Natural Science Foundation of China+1 种基金Projects(2021YFF0502100,2021YFB2600900)supported by the National Key R&D Program of ChinaProject(2022JDTD0015)supported by the Sichuan Province Youth Science and Technology Innovation Team,China。
文摘The interface of slab track laid in cold regions is prone to debonding under the coupling of freeze-thaw cyclesand temperature loads.Based on the composite specimen tests,the parameters of cohesive zone model were obtained andused in a simulation model of CRTS III prefabricated slab track to study the interlayer damage.The results show that 1)the digital image correlation(DIC)technique can accurately capture the strain field changes on the interface of compositespecimens under splitting and shear loading;2)when the temperature gradient is−40℃/m−60℃/m,the interfacedamage of the slab track is minimal and presents different patterns of expansion under positive and negative temperaturegradients,each corresponding to damage of the cohesive element dominated by shear stress and normal tensile stress,respectively;3)the reduction of the elastic modulus at the concrete base after freeze-thaw inhibits interface damage andleads to a higher starting temperature gradient load,but cracking can occur on the concrete base after 150 freeze-thaws.For this reason,in the light of damage control of both the interface and concrete base,the elastic modulus of the concretebase is 54%or over that without freeze-thaw cycles.
基金supported by National Key R&D Program of China[Grant No.2022YFB2603400]R&D Project of China State Railway Group Corporation Limited[Grant No.P2021G053]R&D Project of China Academy of Railway Science Corporation Limited[Grant No.2023YJ200].
文摘Purpose-Temperature is an important load for a ballastless track.However,little research has been conducted on the dynamic responses when a train travels on a ballastless track under the temperature gradient.The dynamic responses under different temperature gradients of the slab are theoretically investigated in this work.Design/methodology/approach-Considering the moving train,the temperature gradient of the slab,and the gravity of the slab track,a dynamic model for a high-speed train that runs along the CRTS Ⅲ slab track on subgrade is developed by a nonlinear coupled way in Abaqus.Findings-The results are as follows:(1)The upward transmission of the periodic deformation of the slab causes periodic track irregularity.(2)Because of the geometric constraint of limiting structures,the maximum bending stresses of the slab occur near the end of the slab under positive temperature gradients,but in the middle of the slab under negative temperature gradients.(3)The periodic deformation of the slab can induce periodic changes in the interlayer stiffness and contact status,leading to a large vibration of the slab.Because of the vibration-reduction capacity of the fastener and the larger mass of the concrete base,the accelerations of both the slab and concrete base are far less than the acceleration of the rail.Originality/value-This study reveals the influence mechanism of temperature gradient-induced periodic deformation in the dynamic responses of the train-track system,and it also provides a guide for the safe service of CRTS Ⅲ slab track.
