The sonocatalytic damage of bovine serum albumin （BSA） was studied in the presence of nanometer titanium dioxide （TiO2） powders by low frequency （80 kHz） ultrasound. The destruction of secondary structure and ch...The sonocatalytic damage of bovine serum albumin （BSA） was studied in the presence of nanometer titanium dioxide （TiO2） powders by low frequency （80 kHz） ultrasound. The destruction of secondary structure and change of α-helical structure of BSA were reflected by ultraviolet （UV） and circular dichroism （CD） spectroscopies.展开更多
The Dye Sensitized Solar Cell (DSSC) plays an important role because of low material cost, ease of production and high conversion efficiency as compared to other thin-film solar cell technologies. The main objective i...The Dye Sensitized Solar Cell (DSSC) plays an important role because of low material cost, ease of production and high conversion efficiency as compared to other thin-film solar cell technologies. The main objective is to create and find the best configuration of the solar cell based on materials that are inexpensive and highly efficient in solar energy conversion and subsequently test the efficiency of dye sensitized titanium dioxide solar cell. We begin the process with two glass plates coated with Fluorine tin oxide (FTO). Titanium dioxide is applied to the conductive side of one plate and the other plate is coated with graphite. A dye is adsorbed on to the TiO2 layer and then the plates are sandwiched together. A drop of iodide electrolyte is then added between the plates. The tests carried out indoors under a lamp emitting all wavelengths in the visible spectrum were not found to provide consistent data due to substantial heating of the cell. The outdoor tests carried out in natural sunlight exhibited steady voltage at much higher level. Future research will involve the incorporation of quantum dots instead of the organic dye as a sensitizer. Quantum dots have the advantages of providing tunable band gaps and the ability to absorb specific wavelength.展开更多
Titanium dioxide nanoparticles(TiO_2 NPs) are one of the most widely used nanomaterials in the consumer products, agriculture, and energy sectors. Their large demand and widespread applications will inevitably cause d...Titanium dioxide nanoparticles(TiO_2 NPs) are one of the most widely used nanomaterials in the consumer products, agriculture, and energy sectors. Their large demand and widespread applications will inevitably cause damage to organisms and ecosystems. A better understanding of TiO_2 NP toxicity in living organisms may promote risk assessment and safe use practices of these nanomaterials. This review summarizes the toxic effects of TiO_2 NPs on multiple taxa of microorganisms, algae, plants, invertebrates, and vertebrates. The mechanism of TiO_2 NP toxicity to organisms can be outlined in three aspects: The Reactive Oxygen Species(ROS)produced by TiO_2 NPs following the induction of electron–hole pairs; cell wall damage and lipid peroxidation of the cell membrane caused by NP-cell attachment by electrostatic force owing to the large surface area of TiO_2 NPs; and TiO_2 NP attachment to intracellular organelles and biological macromolecules following damage to the cell membranes.展开更多
The electrochemical reduction of solid TiO2 directly to solid metal is a promising alternative to the current Kroll process. The present work is aimed at studying the effect of electrolysis voltage on the rate of elec...The electrochemical reduction of solid TiO2 directly to solid metal is a promising alternative to the current Kroll process. The present work is aimed at studying the effect of electrolysis voltage on the rate of electrochemical reduction. The products of electrochemical reduction of TiO2 and Ti2O were examined using the scanning electron microscopy （SEM） and X-ray diffraction （XRD） techniques. The results show that Ti2O was reduced to low valent titanium oxide at 1.5 -1.7 V, which was the result of ionization of oxygen. TiO2 and Ti20 were reduced to titanium metal at 2.1-3.1 V, which was the co-action of ionization of oxygen and calciothermic reduction. The oxygen content decreased rapidly with voltage increasing from 2.1 to 2.6 V, while it changed little from 2.6 to 3.1 V. The optimized cell voltage was 2.6-3.1 V.展开更多
A series of copper-cobalt oxides supported on nano-titanium dioxide were prepared for the reduction of nitric oxide with carbon monoxide and characterized using techniques such as XRD, BET and TPR. Catalyst CuCoOx/TiO...A series of copper-cobalt oxides supported on nano-titanium dioxide were prepared for the reduction of nitric oxide with carbon monoxide and characterized using techniques such as XRD, BET and TPR. Catalyst CuCoOx/TiO2 with Cu/Co molar ratio of 1/2, CuCo total loading of 30% at the calcination temperature of 350℃ formed CuCo204 spinel and had the highest activity. NO conversion reached 98.9% at 200℃. Mechanism of the reduction was also investigated, N20 was mainly yielded below 100℃, while N2 was produced instead at higher temperature. O2 was supposed to accelerate the reaction between NOx and CO for its oxidation of NO to give more easily reduced NO2, but the oxidation of CO by O2 to CO2 decreased the speed of the reaction greatly. Either SO2 or H20 had no adverse impact on the activity of NO reduction; however, in the presence of both SO2 and H20, the catalyst deactivated quickly.展开更多
A series of TiO 2-XSiO 2[X denotes the molar fraction(%) of silica in the mixed oxides] with different \{n(Ti)\}/n(Si) ratios was prepared with ammonia water as a hydrolysis catalyst. The photocatalysts prepared wer...A series of TiO 2-XSiO 2[X denotes the molar fraction(%) of silica in the mixed oxides] with different \{n(Ti)\}/n(Si) ratios was prepared with ammonia water as a hydrolysis catalyst. The photocatalysts prepared were characterized by XRD, thermal analysis, FTIR, UV-Vis and SPS. The characterization results of FTIR and UV-Vis spectra show that Ti atoms were gradually changed from octahedral coordination to tetrahedral coordination with the addition of silica, which is not beneficial for obtaining strong Brnsted acidity and higher photocatalytic activity. The photocatalytic activity experiments, which were conducted by using heptane(or SO 2) as the model reactant, showed that TiO 2-SiO 2 containing a suitable amount of silica can exhibit much higher photocatalytic activity than pure TiO 2. The enhanced photocatalytic activity can be attributed to three following factors: (1) smaller crystalline size; (2) higher thermal stability; (3) the new strong Brnsted acidity.展开更多
This study introduced TiO2-pillared clays （TiO2-PILC） as a support for the catalytic oxidation of NO and analyzed the performance of chromium oxides as the active site of the oxidation process. Cr-based catalysts we...This study introduced TiO2-pillared clays （TiO2-PILC） as a support for the catalytic oxidation of NO and analyzed the performance of chromium oxides as the active site of the oxidation process. Cr-based catalysts were prepared by a wet impregnation method. It was found that the 10 wt.% chromium doping on the support achieved the best catalytic activity. At 350℃, the NO conversion was 61% under conditions of GHSV = 23600 hr^-l. The BET data showed that the support particles had a mesoporous structure. Hz-TPR showed that Cr（10）TiP （10 wt.% Cr doping on TiO2-PILC） clearly exhibited a smooth single peak. EPR and XPS were used to elucidate the oxidation process. During the NO ＋ O2 adsorption, the intensity of evolution of superoxide ions （O2^-） increased. The content of Cr^3＋ on the surface of the used catalyst was 40.37%, but when the used catalyst continued adsorbing NO, the Cr^3＋ increased to 50.28%. Additionally, Oα/Oβ increased markedly through the oxidation process. The NO conversion decreased when SO2 was added into the system, but when the SO2 was removed, the catalytic activity recovered almost up to the initial level. FT-IR spectra did not show a distinct characteristic peak of SO4^2-.展开更多
TiO_2 modified Al_2O_3 binary oxide was prepared by a wet-impregnation method and used as the support for ruthenium catalyst. The catalytic performance of Ru/TiO_2–Al_2O_3catalyst in CO_2 methanation reaction was inv...TiO_2 modified Al_2O_3 binary oxide was prepared by a wet-impregnation method and used as the support for ruthenium catalyst. The catalytic performance of Ru/TiO_2–Al_2O_3catalyst in CO_2 methanation reaction was investigated. Compared with Ru/Al_2O_3 catalyst, the Ru/TiO_2–Al_2O_3catalytic system exhibited a much higher activity in CO_2 methanation reaction. The reaction rate over Ru/TiO_2–Al_2O_3 was 0.59 mol CO_2·(g Ru)1·h-1, 3.1 times higher than that on Ru/Al_2O_3[0.19 mol CO_2·(gRu)-1·h-1]. The effect of TiO_2 content and TiO_2–Al_2O_3calcination temperature on catalytic performance was addressed. The corresponding structures of each catalyst were characterized by means of H_2-TPR, XRD, and TEM. Results indicated that the averaged particle size of the Ru on TiO_2–Al_2O_3support is 2.8 nm, smaller than that on Al_2O_3 support of 4.3 nm. Therefore, we conclude that the improved activity over Ru/TiO_2–Al_2O_3catalyst is originated from the smaller particle size of ruthenium resulting from a strong interaction between Ru and the rutile-TiO_2 support, which hindered the aggregation of Ru nanoparticles.展开更多
A simple and effective method of removing polluted organics in water is reported here.Titanium dioxide is a catalyst in photo-oxidation of monocrotophos.The mechanism of photocatalytic oxidation and the kinetics of th...A simple and effective method of removing polluted organics in water is reported here.Titanium dioxide is a catalyst in photo-oxidation of monocrotophos.The mechanism of photocatalytic oxidation and the kinetics of the reaction were studied. This same principle also leads to the construction of instrument of PTR-FIA analysis for monitoring organic phosphorus and phosphate in water.展开更多
Nitric oxide(NO) from flue gas is hard to remove because of low solubility and reactivity. A new technology for photocatalytic oxidation of NO using ultraviolet(UV)/TiO2/H2O2 process is studied in an efficient laborat...Nitric oxide(NO) from flue gas is hard to remove because of low solubility and reactivity. A new technology for photocatalytic oxidation of NO using ultraviolet(UV)/TiO2/H2O2 process is studied in an efficient laboratory-scale reactor. Effects of several key operational parameters on NO removal efficiency are studied, including TiO2 content, H2O2 initial concentration, UV lamp power, NO initial content, oxygen volume fraction and TiO2/H2O2 solution volume. The results illustrate that the NO removal efficiency increases with the increasing of H2O2 initial concentration or UV lamp power. Meanwhile, a lower NO initial content or a higher TiO2/H2O2 solution volume will result in higher NO removal efficiency. In addition, oxygen volume fraction has a little effect.The highest NO removal efficiency is achieved at the TiO2 content of 0.75 g/L, H2O2 initial concentration of 2.5 mol/L, UV lamp power of 36 W, NO initial content of 206×10-6 and TiO2/H2O2 solution volume of 600 m L. It is beneficial for the development and application of NO removal from coal-fired flue gas with UV/TiO2/H2O2 process.展开更多
This research work aims to reduce the band gap of thin layers of titanium oxide by the incorporation of graphene oxide sheets. Thin layers of the TiO2-GO composites were prepared on a glass substrate by the spin-coati...This research work aims to reduce the band gap of thin layers of titanium oxide by the incorporation of graphene oxide sheets. Thin layers of the TiO2-GO composites were prepared on a glass substrate by the spin-coating technique from GO and an aqueous solution of TiO2. A significant decrease in optical band gap was observed at the TiO2-GO compound compared to that of pure TiO2. Samples as prepared were characterized using XRD, SEM and UV-visible spectra. XRD analysis revealed the amorphous nature of the deposited layers. Scanning electron microscope reveals the dispersion of graphene nanofiles among titanium oxide nanoparticles distributed at the surface with an almost uniform size distribution. The band gap has been calculated and is around 2 eV after incorporation of Graphene oxide. The chemical bond C-Ti between the titanium oxide and graphene sheets is at the origin of this reduction.展开更多
Titanium is a very important element for several industrial applications, being one of the ninth most abundant elements in the Earth’s crust (0.63% wt). In this work it will discuss the different mining and industria...Titanium is a very important element for several industrial applications, being one of the ninth most abundant elements in the Earth’s crust (0.63% wt). In this work it will discuss the different mining and industrial activities involved in the production of titanium dioxide. The first step analyzed will treat about the beneficiation mining process of titanium mineral, and secondly, it will discuss the two main processes of the TiO2 manufacturing (sulphate and chloride routes). In addition, we will show different uses of the titanium dioxide pigment as filler in paper, plastics and rubber industries and as flux in glass manufacture, etc. Finally, we will show that the old wastes are currently called co-products since they were valorized, being commercialized by the Spanish industry of TiO2 production in different fields such as agriculture, civil engineering, or cement manufacturing.展开更多
The preparation, characterization and properties of titania overlayer on Fe(110) substrate is hereby reported. The TiO_X overlayer was found to form in a layer-by-layer mode with a suboxide of titanium in the form of ...The preparation, characterization and properties of titania overlayer on Fe(110) substrate is hereby reported. The TiO_X overlayer was found to form in a layer-by-layer mode with a suboxide of titanium in the form of TiO migrating into the Fe substrate and Fe migrating into the deposited layer of TiO_X simultaneously during the deposition.展开更多
Mesoporous TiO2 （m-TiO2） nanoparticles were used to prepare the porous film electrodes for dye-sensitized solar cells, and a second metal oxide （MgO, ZnO, A1203, or NiO） modifi- cation was carried out by dipping t...Mesoporous TiO2 （m-TiO2） nanoparticles were used to prepare the porous film electrodes for dye-sensitized solar cells, and a second metal oxide （MgO, ZnO, A1203, or NiO） modifi- cation was carried out by dipping the m-TiO2 electrode into their respective nitrate solution followed by annealing at 500 ℃. Experimental results indicated that the above second metal oxide modifications on m-TiO2 electrode are shown in all cases to act as barrier layer for the interracial charge transfer processes, but film electron transport and interfacial charge recombination characteristics under applied bias voltage were dependent significantly on the existing states and kinds of these second metal oxides. Those changes based on sec- ond metal oxide modifications showed good correlation with the current-voltage analyses of dye-sensitized solar cell, and all modifications were found to increase the open-circuit photo- voltage in various degrees, while the MgO, ZnO, and NiO modifications result in 23%, 13%, and 6% improvement in cell conversion efficiency, respectively. The above observations indi- cate that controlling the charge transport and recombination is very important to improve the photovoltaic performance of TiO2-based solar cell.展开更多
The detection on tetracycline( TC) in drinking water poses an environmental issue since TC has been widely used to prevent animal disease and promote their growth. In addition,TC was difficult to remove or biodegrade,...The detection on tetracycline( TC) in drinking water poses an environmental issue since TC has been widely used to prevent animal disease and promote their growth. In addition,TC was difficult to remove or biodegrade,which posed a challenge to the conventional techniques. In this work,the batch experiments on TC adsorption in aqueous solution of hydrogel( HG) consisting of graphene oxide( GO) and TiO_2 nanotubes( TN) were successfully conducted. HG composite( HG-TN-GO) was prepared with TN and GO with self-assembly method during the oxidation-reduction reaction,and criogel( CG) with TN and GO was characterized by pH at point of zero charge( pH_(pzc)), transmission electron microscopy, Raman spectroscopy and X-ray photoelectron spectroscopy( XPS). The adsorption capacity of HG-TN-GO on TC was evaluated by analyzing its isotherms. The maximum adsorption capacity reached 751. 3 mg/g. Besides,the adsorption isotherms were well fitted by the Langmuir model, with the theoretical maximum( q_m) of 797. 0 mg/g. The adsorption process was systematically studied by varying pH during the whole adsorption process. The adsorption occurred probably via π-π interaction and cation-π bonding between TC and the HG-TN-GO surface. The composite could be regenerated in 50% ethanol aqueous solution,without significant capacity loss. After 6 recycles,the decrease of adsorption capacity was less than 10%.展开更多
Electromagnetic wave absorbing materials are urgently required in the fields of medicine,communication,and military.However,the thickness,weight,narrow effective bandwidth,and weak absorbing ability of the materials r...Electromagnetic wave absorbing materials are urgently required in the fields of medicine,communication,and military.However,the thickness,weight,narrow effective bandwidth,and weak absorbing ability of the materials restrict their further application.In this work,a double-layer hollow nanocube with a dielectric titanium dioxide(TiO_(2))shell and a magnetic CoFe oxide inner shell is prepared.Prussian blue(PB)is prepared by the hydrothermal method,and used as the template to prepare PB@CoFe PB analogue(PBA).After selective etching and further calcination,hollow CoFe oxide particles are obtained.The obtained particles are then coated with SiO_(2)and TiO_(2),respectively,and the intermediate layer is dislodged to obtain the final CoFe oxide@TiO_(2)with the hollow double shell structure.The obtained double-layer hollow structure can effectively capture the incident electromagnetic waves,and increase the propagation path.Moreover,the obvious enhancement of interface polarization and the improvement of impedance matching enhance the wave absorbing ability of the material.The analysis results show that,the structure is stable and the dispersion is good.The maximum reflection loss(RL)at 10 GHz is as high as-46.1 dB with the sample thickness of 1.6 mm.The light-weight and high-efficiency CoFe oxide@TiO_(2)absorber is promised to be used in commercial and military aerospace fields.展开更多
Photoelectrochemical studies on TiO2 doped with Ce2O3 or CeO2 took place in aqueous solutions of [Fe(CN)6]4- as the source of hydrated electrons. Our studies show that doping TiO2 with CeO2 gave better photocatalytic ...Photoelectrochemical studies on TiO2 doped with Ce2O3 or CeO2 took place in aqueous solutions of [Fe(CN)6]4- as the source of hydrated electrons. Our studies show that doping TiO2 with CeO2 gave better photocatalytic reduction of [Fe(CN)6]3- than TiO2 doped with Ce2O3. However the TiO2 assemblies doped with either Ce(III) or Ce(IV) oxides give less photochemical reduction of [Fe(CN)6]3- that the oxides of pure metals (Ti or Ce). In both cases a lowering of the band gaps of TiO2 was noticed. Immobilized TiO2 doped with Ce oxides on a FTO (Fluorine Ten Oxide) surface gave greater photocurrent with I2/I3– than that recorded for [Fe(CN)6]3-/4- redox systems. Our studies indicate that the TiO2 doped with Ce2O3 or CeO2 maintained photoactivity after being immobilized in thin solid sheets and can be used in all solid state photoelectron-chemical cells.展开更多
ZrO2/TiO2 composite photocatalytic film was produced on the pure titanium substrate using in-situ Zr（OH）4 colloidal particle by the micro-arc oxidation technique and characterized by scanning electron microscope （...ZrO2/TiO2 composite photocatalytic film was produced on the pure titanium substrate using in-situ Zr（OH）4 colloidal particle by the micro-arc oxidation technique and characterized by scanning electron microscope （SEM）, energy dispersive X-ray （EDX）, X-ray diffraction （XRD） and ultraviolet-visible （UV-Vis） spectrophotometer. The composite film shows a lamellar and porous structure which consists of anatase, futile and ZrO2 phases. The optical absorption edge of film is shifted to longer wavelength when ZrO2 is introduced to TiO2. Furthermore, the photocatalytic reaction rate constants of degradation of rhodamine B solution with ZrO2/TiO2 composite film and pure TiO2 film under ultraviolet irradiation are measured as 0.0442 and 0.0186 h 1, respectively.展开更多
A layer of porous film containing Ca and P was prepared by the micro-arc oxidation method on the surface of a novel near β biomedical Ti-3Zr-2Sn-3Mo-25Nb alloy, and then NH2- active group was introduced to the films ...A layer of porous film containing Ca and P was prepared by the micro-arc oxidation method on the surface of a novel near β biomedical Ti-3Zr-2Sn-3Mo-25Nb alloy, and then NH2- active group was introduced to the films by activation treatment. The phase composition, surface micro-topography and elemental characteristics of the micro-arc oxidation films were investigated with XRD, SEM, EDS and XPS, and the osteoinduction of the micro-arc oxidation films was tested using the simulated body fluid immersion, the in-vitro osteoblast cultivation test and animal experiment. The results show that the oxide layer is a kind of porous ceramic intermixture and contains Ca and P. The films in the simulated body fluid can induce apatite formation, resulting in excellent bioactivity. The cell test discovers that osteoblasts can grow well on the surface of micro-arc oxidation films. And the Ti-3Zr-2Sn-3Mo-25Nb biomedical alloy coated with active porous calcium-phosphate films shows better osteoinduction in vivo.展开更多
Increasing application of nanotechnology highlights the need to clarify and understand nanotoxicity. Mammalian and in vitro studies have raised concerns about the toxicity of titanium dioxide nanoparticles （TiO2-NPs...Increasing application of nanotechnology highlights the need to clarify and understand nanotoxicity. Mammalian and in vitro studies have raised concerns about the toxicity of titanium dioxide nanoparticles （TiO2-NPs）, but there are limited data on ecotoxicity to aquatic organisms. In this work, the sub-acute toxicity of TiO2-NPs to carp （Cyprinus carpio） was assessed. Superoxide dismutase （SOD）, catalase （CAT） and peroxidase （POD） activities and lipid peroxidation （LPO） levels in liver, gill and brain tissues of carps varied with concentration of TiO2-NPs suspensions and exposure time （up to 8 d）. As a result, 100 and 200 mg/L TiO2-NPs caused statistically significant decrease in SOD, CAT and POD activities and significant increase in LPO levels in tissues （P 〈 0.05）, suggesting that the fish exposed to these two concentrations of TiO2-NPs suffered from the oxidative stress. The extent of depletion of antioxidant enzymes activities and the elevation of LPO in the liver was the greatest, indicating that the liver might be the most susceptible organ to TiO2-NPs exposure. In addition, carps had gill pathologies including edema and thickening of gill lamellae as well as gill filaments, and liver pathologies including necrotic and apoptosis hepatocytes after exposed to 100 and 200 mg/L TiO2-NPs for 20 d. These results indicated a potential risk from TiO2-NPs released into the aqueous environment.展开更多
基金We greatly acknowledge the National Natural Science Foundation of China for financial support.
文摘The sonocatalytic damage of bovine serum albumin （BSA） was studied in the presence of nanometer titanium dioxide （TiO2） powders by low frequency （80 kHz） ultrasound. The destruction of secondary structure and change of α-helical structure of BSA were reflected by ultraviolet （UV） and circular dichroism （CD） spectroscopies.
文摘The Dye Sensitized Solar Cell (DSSC) plays an important role because of low material cost, ease of production and high conversion efficiency as compared to other thin-film solar cell technologies. The main objective is to create and find the best configuration of the solar cell based on materials that are inexpensive and highly efficient in solar energy conversion and subsequently test the efficiency of dye sensitized titanium dioxide solar cell. We begin the process with two glass plates coated with Fluorine tin oxide (FTO). Titanium dioxide is applied to the conductive side of one plate and the other plate is coated with graphite. A dye is adsorbed on to the TiO2 layer and then the plates are sandwiched together. A drop of iodide electrolyte is then added between the plates. The tests carried out indoors under a lamp emitting all wavelengths in the visible spectrum were not found to provide consistent data due to substantial heating of the cell. The outdoor tests carried out in natural sunlight exhibited steady voltage at much higher level. Future research will involve the incorporation of quantum dots instead of the organic dye as a sensitizer. Quantum dots have the advantages of providing tunable band gaps and the ability to absorb specific wavelength.
基金supported by the National Natural Science Foundation of China (Nos.21607043,21577032)the Youth Innovation Promotion Association,Chinese Academy of Sciences (No.2018054)+1 种基金the Fundamental Research Funds for the Central Universities (Nos.2016ZZD06,2018ZD11)the Open Project of Key Laboratory of Environmental Biotechnology,CAS (No.kf2016009)
文摘Titanium dioxide nanoparticles(TiO_2 NPs) are one of the most widely used nanomaterials in the consumer products, agriculture, and energy sectors. Their large demand and widespread applications will inevitably cause damage to organisms and ecosystems. A better understanding of TiO_2 NP toxicity in living organisms may promote risk assessment and safe use practices of these nanomaterials. This review summarizes the toxic effects of TiO_2 NPs on multiple taxa of microorganisms, algae, plants, invertebrates, and vertebrates. The mechanism of TiO_2 NP toxicity to organisms can be outlined in three aspects: The Reactive Oxygen Species(ROS)produced by TiO_2 NPs following the induction of electron–hole pairs; cell wall damage and lipid peroxidation of the cell membrane caused by NP-cell attachment by electrostatic force owing to the large surface area of TiO_2 NPs; and TiO_2 NP attachment to intracellular organelles and biological macromolecules following damage to the cell membranes.
基金the Postdoctoral Science Foundation of China (No. 20060400409).
文摘The electrochemical reduction of solid TiO2 directly to solid metal is a promising alternative to the current Kroll process. The present work is aimed at studying the effect of electrolysis voltage on the rate of electrochemical reduction. The products of electrochemical reduction of TiO2 and Ti2O were examined using the scanning electron microscopy （SEM） and X-ray diffraction （XRD） techniques. The results show that Ti2O was reduced to low valent titanium oxide at 1.5 -1.7 V, which was the result of ionization of oxygen. TiO2 and Ti20 were reduced to titanium metal at 2.1-3.1 V, which was the co-action of ionization of oxygen and calciothermic reduction. The oxygen content decreased rapidly with voltage increasing from 2.1 to 2.6 V, while it changed little from 2.6 to 3.1 V. The optimized cell voltage was 2.6-3.1 V.
基金supported by the Doctoral Fund of Ministry of Education of China(No.200805301004)the Hunan Provincial Natural Science Foundation of China(No.07JJ4003)the Scientific Research Fund of Hunan Provincial Education Department(No.08C890)
文摘A series of copper-cobalt oxides supported on nano-titanium dioxide were prepared for the reduction of nitric oxide with carbon monoxide and characterized using techniques such as XRD, BET and TPR. Catalyst CuCoOx/TiO2 with Cu/Co molar ratio of 1/2, CuCo total loading of 30% at the calcination temperature of 350℃ formed CuCo204 spinel and had the highest activity. NO conversion reached 98.9% at 200℃. Mechanism of the reduction was also investigated, N20 was mainly yielded below 100℃, while N2 was produced instead at higher temperature. O2 was supposed to accelerate the reaction between NOx and CO for its oxidation of NO to give more easily reduced NO2, but the oxidation of CO by O2 to CO2 decreased the speed of the reaction greatly. Either SO2 or H20 had no adverse impact on the activity of NO reduction; however, in the presence of both SO2 and H20, the catalyst deactivated quickly.
基金Supported by the National Natural Science Foundation of China(No.2 0 2 770 15 )
文摘A series of TiO 2-XSiO 2[X denotes the molar fraction(%) of silica in the mixed oxides] with different \{n(Ti)\}/n(Si) ratios was prepared with ammonia water as a hydrolysis catalyst. The photocatalysts prepared were characterized by XRD, thermal analysis, FTIR, UV-Vis and SPS. The characterization results of FTIR and UV-Vis spectra show that Ti atoms were gradually changed from octahedral coordination to tetrahedral coordination with the addition of silica, which is not beneficial for obtaining strong Brnsted acidity and higher photocatalytic activity. The photocatalytic activity experiments, which were conducted by using heptane(or SO 2) as the model reactant, showed that TiO 2-SiO 2 containing a suitable amount of silica can exhibit much higher photocatalytic activity than pure TiO 2. The enhanced photocatalytic activity can be attributed to three following factors: (1) smaller crystalline size; (2) higher thermal stability; (3) the new strong Brnsted acidity.
基金supported by the Assembly Foundation of the Industry and Information Ministry of China 2012(543)the National Natural Science Foundation of China(No.U1162119+5 种基金51078185)the Scientific Research Project of Environmental Protection Department of Jiangsu Province(No.2013003201112)the Research Fund for the Doctoral Program of Higher Education of China(No.20113219110009)the Industry-Academia Cooperation Innovation Fund Projects of Jiangsu Province(No.BY2012025)the research fund of Key Laboratory for Advanced Technology in Environmental Protection of Jiangsu Province(No.AE201001)
文摘This study introduced TiO2-pillared clays （TiO2-PILC） as a support for the catalytic oxidation of NO and analyzed the performance of chromium oxides as the active site of the oxidation process. Cr-based catalysts were prepared by a wet impregnation method. It was found that the 10 wt.% chromium doping on the support achieved the best catalytic activity. At 350℃, the NO conversion was 61% under conditions of GHSV = 23600 hr^-l. The BET data showed that the support particles had a mesoporous structure. Hz-TPR showed that Cr（10）TiP （10 wt.% Cr doping on TiO2-PILC） clearly exhibited a smooth single peak. EPR and XPS were used to elucidate the oxidation process. During the NO ＋ O2 adsorption, the intensity of evolution of superoxide ions （O2^-） increased. The content of Cr^3＋ on the surface of the used catalyst was 40.37%, but when the used catalyst continued adsorbing NO, the Cr^3＋ increased to 50.28%. Additionally, Oα/Oβ increased markedly through the oxidation process. The NO conversion decreased when SO2 was added into the system, but when the SO2 was removed, the catalytic activity recovered almost up to the initial level. FT-IR spectra did not show a distinct characteristic peak of SO4^2-.
基金Supported by the National Natural Science Foundation of China(211031735127108721476226 and 51471076)DICP Fundamental Research Program for Clean Energy(DICPM201307)
文摘TiO_2 modified Al_2O_3 binary oxide was prepared by a wet-impregnation method and used as the support for ruthenium catalyst. The catalytic performance of Ru/TiO_2–Al_2O_3catalyst in CO_2 methanation reaction was investigated. Compared with Ru/Al_2O_3 catalyst, the Ru/TiO_2–Al_2O_3catalytic system exhibited a much higher activity in CO_2 methanation reaction. The reaction rate over Ru/TiO_2–Al_2O_3 was 0.59 mol CO_2·(g Ru)1·h-1, 3.1 times higher than that on Ru/Al_2O_3[0.19 mol CO_2·(gRu)-1·h-1]. The effect of TiO_2 content and TiO_2–Al_2O_3calcination temperature on catalytic performance was addressed. The corresponding structures of each catalyst were characterized by means of H_2-TPR, XRD, and TEM. Results indicated that the averaged particle size of the Ru on TiO_2–Al_2O_3support is 2.8 nm, smaller than that on Al_2O_3 support of 4.3 nm. Therefore, we conclude that the improved activity over Ru/TiO_2–Al_2O_3catalyst is originated from the smaller particle size of ruthenium resulting from a strong interaction between Ru and the rutile-TiO_2 support, which hindered the aggregation of Ru nanoparticles.
文摘A simple and effective method of removing polluted organics in water is reported here.Titanium dioxide is a catalyst in photo-oxidation of monocrotophos.The mechanism of photocatalytic oxidation and the kinetics of the reaction were studied. This same principle also leads to the construction of instrument of PTR-FIA analysis for monitoring organic phosphorus and phosphate in water.
基金Project(2011CB201505)supported by the National Key Basic Research Program of ChinaProject(BA2011031)supported by the Special Fund of Transformation of Scientific and Technological Achievements of Jiangsu Province,China
文摘Nitric oxide(NO) from flue gas is hard to remove because of low solubility and reactivity. A new technology for photocatalytic oxidation of NO using ultraviolet(UV)/TiO2/H2O2 process is studied in an efficient laboratory-scale reactor. Effects of several key operational parameters on NO removal efficiency are studied, including TiO2 content, H2O2 initial concentration, UV lamp power, NO initial content, oxygen volume fraction and TiO2/H2O2 solution volume. The results illustrate that the NO removal efficiency increases with the increasing of H2O2 initial concentration or UV lamp power. Meanwhile, a lower NO initial content or a higher TiO2/H2O2 solution volume will result in higher NO removal efficiency. In addition, oxygen volume fraction has a little effect.The highest NO removal efficiency is achieved at the TiO2 content of 0.75 g/L, H2O2 initial concentration of 2.5 mol/L, UV lamp power of 36 W, NO initial content of 206×10-6 and TiO2/H2O2 solution volume of 600 m L. It is beneficial for the development and application of NO removal from coal-fired flue gas with UV/TiO2/H2O2 process.
文摘This research work aims to reduce the band gap of thin layers of titanium oxide by the incorporation of graphene oxide sheets. Thin layers of the TiO2-GO composites were prepared on a glass substrate by the spin-coating technique from GO and an aqueous solution of TiO2. A significant decrease in optical band gap was observed at the TiO2-GO compound compared to that of pure TiO2. Samples as prepared were characterized using XRD, SEM and UV-visible spectra. XRD analysis revealed the amorphous nature of the deposited layers. Scanning electron microscope reveals the dispersion of graphene nanofiles among titanium oxide nanoparticles distributed at the surface with an almost uniform size distribution. The band gap has been calculated and is around 2 eV after incorporation of Graphene oxide. The chemical bond C-Ti between the titanium oxide and graphene sheets is at the origin of this reduction.
基金This research has been partially supported by the Government of Andalusia’s project“Characterization and modelling of the phosphogypsum stacks from Huelva for their environmental management and control”(Ref.:RNM-6300) by National Institution of Higher Education,Science,Technology and Innovation of the Republic of Ecuador-(SENESCYT for its acronym in Spanish)+2 种基金The authors would like to acknowledge the financial support received from the company Tioxide-Huelva by the research projects“Valorization of red gypsum from the industrial production of titanium dioxide”(PROFIT,CIT-310200-2007-47)“Applications of red gypsum and Tionite waste in commercial applications”The authors also thank to the technical staff for the advisory provided in the explanation of the results.
文摘Titanium is a very important element for several industrial applications, being one of the ninth most abundant elements in the Earth’s crust (0.63% wt). In this work it will discuss the different mining and industrial activities involved in the production of titanium dioxide. The first step analyzed will treat about the beneficiation mining process of titanium mineral, and secondly, it will discuss the two main processes of the TiO2 manufacturing (sulphate and chloride routes). In addition, we will show different uses of the titanium dioxide pigment as filler in paper, plastics and rubber industries and as flux in glass manufacture, etc. Finally, we will show that the old wastes are currently called co-products since they were valorized, being commercialized by the Spanish industry of TiO2 production in different fields such as agriculture, civil engineering, or cement manufacturing.
文摘The preparation, characterization and properties of titania overlayer on Fe(110) substrate is hereby reported. The TiO_X overlayer was found to form in a layer-by-layer mode with a suboxide of titanium in the form of TiO migrating into the Fe substrate and Fe migrating into the deposited layer of TiO_X simultaneously during the deposition.
文摘Mesoporous TiO2 （m-TiO2） nanoparticles were used to prepare the porous film electrodes for dye-sensitized solar cells, and a second metal oxide （MgO, ZnO, A1203, or NiO） modifi- cation was carried out by dipping the m-TiO2 electrode into their respective nitrate solution followed by annealing at 500 ℃. Experimental results indicated that the above second metal oxide modifications on m-TiO2 electrode are shown in all cases to act as barrier layer for the interracial charge transfer processes, but film electron transport and interfacial charge recombination characteristics under applied bias voltage were dependent significantly on the existing states and kinds of these second metal oxides. Those changes based on sec- ond metal oxide modifications showed good correlation with the current-voltage analyses of dye-sensitized solar cell, and all modifications were found to increase the open-circuit photo- voltage in various degrees, while the MgO, ZnO, and NiO modifications result in 23%, 13%, and 6% improvement in cell conversion efficiency, respectively. The above observations indi- cate that controlling the charge transport and recombination is very important to improve the photovoltaic performance of TiO2-based solar cell.
基金Environmental Engineering,Natural Science Foundation of China(No.51522805)Innovation Foundation of Nanjing Institute of Technology,China(No.CKJB201410)
文摘The detection on tetracycline( TC) in drinking water poses an environmental issue since TC has been widely used to prevent animal disease and promote their growth. In addition,TC was difficult to remove or biodegrade,which posed a challenge to the conventional techniques. In this work,the batch experiments on TC adsorption in aqueous solution of hydrogel( HG) consisting of graphene oxide( GO) and TiO_2 nanotubes( TN) were successfully conducted. HG composite( HG-TN-GO) was prepared with TN and GO with self-assembly method during the oxidation-reduction reaction,and criogel( CG) with TN and GO was characterized by pH at point of zero charge( pH_(pzc)), transmission electron microscopy, Raman spectroscopy and X-ray photoelectron spectroscopy( XPS). The adsorption capacity of HG-TN-GO on TC was evaluated by analyzing its isotherms. The maximum adsorption capacity reached 751. 3 mg/g. Besides,the adsorption isotherms were well fitted by the Langmuir model, with the theoretical maximum( q_m) of 797. 0 mg/g. The adsorption process was systematically studied by varying pH during the whole adsorption process. The adsorption occurred probably via π-π interaction and cation-π bonding between TC and the HG-TN-GO surface. The composite could be regenerated in 50% ethanol aqueous solution,without significant capacity loss. After 6 recycles,the decrease of adsorption capacity was less than 10%.
基金the National Natural Science Foundation of China(Nos.51773060,5207309151573045)the Shanghai Key Laboratory of Advanced Polymer Materials。
文摘Electromagnetic wave absorbing materials are urgently required in the fields of medicine,communication,and military.However,the thickness,weight,narrow effective bandwidth,and weak absorbing ability of the materials restrict their further application.In this work,a double-layer hollow nanocube with a dielectric titanium dioxide(TiO_(2))shell and a magnetic CoFe oxide inner shell is prepared.Prussian blue(PB)is prepared by the hydrothermal method,and used as the template to prepare PB@CoFe PB analogue(PBA).After selective etching and further calcination,hollow CoFe oxide particles are obtained.The obtained particles are then coated with SiO_(2)and TiO_(2),respectively,and the intermediate layer is dislodged to obtain the final CoFe oxide@TiO_(2)with the hollow double shell structure.The obtained double-layer hollow structure can effectively capture the incident electromagnetic waves,and increase the propagation path.Moreover,the obvious enhancement of interface polarization and the improvement of impedance matching enhance the wave absorbing ability of the material.The analysis results show that,the structure is stable and the dispersion is good.The maximum reflection loss(RL)at 10 GHz is as high as-46.1 dB with the sample thickness of 1.6 mm.The light-weight and high-efficiency CoFe oxide@TiO_(2)absorber is promised to be used in commercial and military aerospace fields.
文摘Photoelectrochemical studies on TiO2 doped with Ce2O3 or CeO2 took place in aqueous solutions of [Fe(CN)6]4- as the source of hydrated electrons. Our studies show that doping TiO2 with CeO2 gave better photocatalytic reduction of [Fe(CN)6]3- than TiO2 doped with Ce2O3. However the TiO2 assemblies doped with either Ce(III) or Ce(IV) oxides give less photochemical reduction of [Fe(CN)6]3- that the oxides of pure metals (Ti or Ce). In both cases a lowering of the band gaps of TiO2 was noticed. Immobilized TiO2 doped with Ce oxides on a FTO (Fluorine Ten Oxide) surface gave greater photocurrent with I2/I3– than that recorded for [Fe(CN)6]3-/4- redox systems. Our studies indicate that the TiO2 doped with Ce2O3 or CeO2 maintained photoactivity after being immobilized in thin solid sheets and can be used in all solid state photoelectron-chemical cells.
基金Project(gf200901002)supported by the Open Research Fund of National Defense Key Disciplines Laboratory of Light Alloy Processing Science and Technology of Nanchang Hangkong University,China
文摘ZrO2/TiO2 composite photocatalytic film was produced on the pure titanium substrate using in-situ Zr（OH）4 colloidal particle by the micro-arc oxidation technique and characterized by scanning electron microscope （SEM）, energy dispersive X-ray （EDX）, X-ray diffraction （XRD） and ultraviolet-visible （UV-Vis） spectrophotometer. The composite film shows a lamellar and porous structure which consists of anatase, futile and ZrO2 phases. The optical absorption edge of film is shifted to longer wavelength when ZrO2 is introduced to TiO2. Furthermore, the photocatalytic reaction rate constants of degradation of rhodamine B solution with ZrO2/TiO2 composite film and pure TiO2 film under ultraviolet irradiation are measured as 0.0442 and 0.0186 h 1, respectively.
基金Project (2005CB623904) supported by the National Basic Research Program of ChinaProject (30770586) supported by the National Natural Science Foundation of China+1 种基金Project (31011120049) supported by the Australia-China special fund, International Science Linkages Program co-supported by the Department of Innovation, Industry, Science and Research of Australia, and the Ministry of Science and Technology and National Science Foundation of ChinaProject (2010ZDKG-96) supported by the major Subject of "13115" Programs of Shaan’xi Province, China
文摘A layer of porous film containing Ca and P was prepared by the micro-arc oxidation method on the surface of a novel near β biomedical Ti-3Zr-2Sn-3Mo-25Nb alloy, and then NH2- active group was introduced to the films by activation treatment. The phase composition, surface micro-topography and elemental characteristics of the micro-arc oxidation films were investigated with XRD, SEM, EDS and XPS, and the osteoinduction of the micro-arc oxidation films was tested using the simulated body fluid immersion, the in-vitro osteoblast cultivation test and animal experiment. The results show that the oxide layer is a kind of porous ceramic intermixture and contains Ca and P. The films in the simulated body fluid can induce apatite formation, resulting in excellent bioactivity. The cell test discovers that osteoblasts can grow well on the surface of micro-arc oxidation films. And the Ti-3Zr-2Sn-3Mo-25Nb biomedical alloy coated with active porous calcium-phosphate films shows better osteoinduction in vivo.
基金supported by the China Postdoctoral Science Foundation Funded Project (No 20080431217)the Cheung Kong Scholar Program of Education Ministry of China
文摘Increasing application of nanotechnology highlights the need to clarify and understand nanotoxicity. Mammalian and in vitro studies have raised concerns about the toxicity of titanium dioxide nanoparticles （TiO2-NPs）, but there are limited data on ecotoxicity to aquatic organisms. In this work, the sub-acute toxicity of TiO2-NPs to carp （Cyprinus carpio） was assessed. Superoxide dismutase （SOD）, catalase （CAT） and peroxidase （POD） activities and lipid peroxidation （LPO） levels in liver, gill and brain tissues of carps varied with concentration of TiO2-NPs suspensions and exposure time （up to 8 d）. As a result, 100 and 200 mg/L TiO2-NPs caused statistically significant decrease in SOD, CAT and POD activities and significant increase in LPO levels in tissues （P 〈 0.05）, suggesting that the fish exposed to these two concentrations of TiO2-NPs suffered from the oxidative stress. The extent of depletion of antioxidant enzymes activities and the elevation of LPO in the liver was the greatest, indicating that the liver might be the most susceptible organ to TiO2-NPs exposure. In addition, carps had gill pathologies including edema and thickening of gill lamellae as well as gill filaments, and liver pathologies including necrotic and apoptosis hepatocytes after exposed to 100 and 200 mg/L TiO2-NPs for 20 d. These results indicated a potential risk from TiO2-NPs released into the aqueous environment.
