A nanoheterojunction composite photocatalyst Bi2O3/TiO2 working under visible-light （λ≥ 420 nm） was prepared by combining two semiconductors Bi2O3 and TiO2 varying the Bi2O3/TiO2 molar ratio. Maleic acid was emplo...A nanoheterojunction composite photocatalyst Bi2O3/TiO2 working under visible-light （λ≥ 420 nm） was prepared by combining two semiconductors Bi2O3 and TiO2 varying the Bi2O3/TiO2 molar ratio. Maleic acid was employed as an organic binder to unite Bi2O3 and TiO2 nanoparticles. The SEM, TEM, XRD and diffuse reflectance spectra were utilized to characterize the prepared Bi2O3/TiO2 nanoheterojunction. The nanocomposite exhibited unusual high photocatalytic activity in decomposing 2-propanol in gas phase and phenol in aqueous phase and, evolution of CO2 under visible light irradiation while the end members exhibited low photocatalytic activity. The composite was optimized to 5 mol% Bi2O3/TiO2. The remarkable high photocatalytic efficiency originates from the unique relative energy band position of Bi2O3 and TiO2 as well as the absorption of visible light by Bi2O3.展开更多
In this paper, a detailed study was carried out on the PTFE reinforced with TiO2 and CaTiO3. The filler content of ceramic powder was a fixed value of 61 wt% and the content of CaTiO3 in PTFE matrix varied from 0 wt% ...In this paper, a detailed study was carried out on the PTFE reinforced with TiO2 and CaTiO3. The filler content of ceramic powder was a fixed value of 61 wt% and the content of CaTiO3 in PTFE matrix varied from 0 wt% to 16 wt% with a step size of 4 wt%. The effects of CaTiO3 loading on the density, moisture absorption, thermal expansion, microstructure and microwave dielectric properties were investigated. As CaTiO3 loading content increased from 0 wt% to 16 wt%, the thermal expansion initially displayed a sharp increase, and showed a slight enhancement when the content of CaTiO3 exceeded 12 wt%. The density experienced a continuous decrease with the addition of CaTiO3. The moisture absorption displayed a steady increase with the increasing CaTiO3 loading amount. The changing of dielectric constant (εr) and loss tangent (tanδ) were similar to that of the moisture absorption in a manner. Good dielectric properties with values of εr = 11.60, tanδ = 0.002 were obtained in the PTFE matrix with 16 wt% CaTiO3 and 45 wt% TiO2.展开更多
Bi2(Te,Se)3 alloys are conventional commercial thermoelectric materials for solid-state refrigeration around room temperature.In recent years,much attention has been paid to various advanced thermoelectric composite m...Bi2(Te,Se)3 alloys are conventional commercial thermoelectric materials for solid-state refrigeration around room temperature.In recent years,much attention has been paid to various advanced thermoelectric composite materials due to the unique thermoelectric properties.In this work,Bi2Se3/TiO2 composites were prepared by hot pressing the plate-like Bi2Se3 powders coated in situ with hydrolyzed hytetabutyl-n-butyl titanate(TNBT),and therefore numerous TiO2 in micrometer size could be formed on the interface of Bi2Se3 grains.The carrier concentration in Bi2Se3 matrix is optimized subject to the addition of n-type semiconductor TiO2,contributing to a significant improved power factor.In the meantime,the lattice thermal conductivity is also suppressed due to the enhanced phonon scattering at Bi2Se3/TiO2 interface and amorphous TiO2 particles.As a consequence,a peak figure of merit(zT)of 0.41 is obtained at 525 K in Bi2Se3/15 mol%TiO2 composites,nearly 50%augment over the pristine Bi2Se3 binary compound.展开更多
TiAl3 particle reinforced pure Al composite has been made by direct reaction among molten Al, TiO2 and a flux. The composite exhibits high Synthetically properties. The strength and hardness are higher than those of p...TiAl3 particle reinforced pure Al composite has been made by direct reaction among molten Al, TiO2 and a flux. The composite exhibits high Synthetically properties. The strength and hardness are higher than those of pure Al matrix by 71.5% and 134% respectively However, the elongation is 20.36%, slightly lower than that of the Al matrix.展开更多
The up-conversion luminescence composite NaYF4：Er3＋/TiO2 is prepared using the sol-gel method. The specimen has good crystallinity and two shapes, i.e., viereck and round, while the sizes of viereck and round partic...The up-conversion luminescence composite NaYF4：Er3＋/TiO2 is prepared using the sol-gel method. The specimen has good crystallinity and two shapes, i.e., viereck and round, while the sizes of viereck and round particles are both micron-sized. The TiO2 has an anatase structure, while the NaYF4 has a hexagonal phase, which can be hardly obtained through the common sol-gel method. Due to the big particle size and the high crystallinity of pure NaYF4： Er3＋, the composite has a small specific surface area that is less than Degussa P25 TiO2. The NaYF4：Er3＋/TiO2 composite shows several emission peaks at 211, 237, and 251 nm under the excitation of 388 nm, at 395 nm and 411 nm under the excitation of 500 nm, and at 467, 481,492, and 508 nm under the excitation of 570 nm.展开更多
Titanium dioxide （TiO2） loaded tungsten trioxide （WO3） composite films are prepared by an E-beam vapor system. Associated with the existence of a heterojunction at the interface of TiO2 and WO3, the prepared TiO2-...Titanium dioxide （TiO2） loaded tungsten trioxide （WO3） composite films are prepared by an E-beam vapor system. Associated with the existence of a heterojunction at the interface of TiO2 and WO3, the prepared TiO2-WO3 composite film shows enhanced photocurrent density, four times than the pure WO3 film illuminated under xenon lamp, and higher incident-photon-to-current conversion e^ciency. By varying the initial TiO2 film thickness, such composite structures could be optimized to obtain the highest photocurrent density. We believe that thin TiO2 films improve the light response and increase the surface roughness of WO3 films. Furthermore, the existence of the heterojunction results in the e^cient charge carriers＇ separation, transfer process, and a lower recombination of electron-hole pairs, which is beneficial for the enhancement of photocurrent density.展开更多
Al 2O 3-SiO 2-TiO 2-ZrO 2 supported membranes were prepar ed by Sol-Gel method. These composite ceramic membranes are level, even and no macro crack. There exist several crystalline phases such as Al 2O 3, TiO...Al 2O 3-SiO 2-TiO 2-ZrO 2 supported membranes were prepar ed by Sol-Gel method. These composite ceramic membranes are level, even and no macro crack. There exist several crystalline phases such as Al 2O 3, TiO 2(a natase), Al 2SiO 5, and ZrO 2 in these membranes. Changing the molar ratio of Al∶Si∶Ti∶Zr,the kinds and content of crystal phases of composite membranes could be different, which may lead to a variety of microstructure of membranes. The surface nanoscale topography and microstructure of membranes were investiga ted by XRD,SEM,AFM,EPMA. The effects of additives and heat treatments on the sur face nanoscale topography and microstructure of composite ceramic membranes were also analyzed.展开更多
TiB2-Al2O3 composite powders were produced by self-propagating high-temperature synthesis（SHS） method with reductive process from B2O3-TiO2-AI system. X-ray diffraction（XRD） and scanning electron microscopy（SEM...TiB2-Al2O3 composite powders were produced by self-propagating high-temperature synthesis（SHS） method with reductive process from B2O3-TiO2-AI system. X-ray diffraction（XRD） and scanning electron microscopy（SEM） analyses show the presence of TiB2 and Al2O3 only in the composite powders produced by SHS. The powders are uniform and free-agglomerate. Transmission electron microscopy （TEM） and high resolution electron microscopy （HREM） observation of microstructure of the composite powders indicate that the interfaces of the TiB2-Al2O3 bond well, without any interfacial reaction products. It is proposed that the good interfacial bonding of the composite powders can be resulted from the TiB2 particles crystallizing and growing on the Al2O3 particles surface with surface defects acting as nucleation centers.展开更多
The conductivities of polyethylene oxide (PEO)-based polymer electrolytes (PE) can be improved by the addition of inorganic inert powder. The composite polymer electrolytes (CPE) PEO10LiX (X=4ClO- or 322N(CFSO)-)-Li2T...The conductivities of polyethylene oxide (PEO)-based polymer electrolytes (PE) can be improved by the addition of inorganic inert powder. The composite polymer electrolytes (CPE) PEO10LiX (X=4ClO- or 322N(CFSO)-)-Li2TiO3 were prepared by solution casting with inorganic solid electrolyte Li2TiO3 powder as a filler. Results showed that the conductivities of PEO10LiClO4-3wt% Li2TiO3 and PEO10LiN(CF3SO2)2-10wt% Li2TiO3 at 30 ℃ were 8.6×10-6 and 5.6×10-5 S·cm-1, respectively. The conductivities of CPE increased with the decrease of filler抯 particle size. The ionic conduction mechanism analysis showed that there may be three conduction routes in the CPE, i.e., PEO bulk, polymer-filler interface and Li2TiO3 crystal.展开更多
文摘A nanoheterojunction composite photocatalyst Bi2O3/TiO2 working under visible-light （λ≥ 420 nm） was prepared by combining two semiconductors Bi2O3 and TiO2 varying the Bi2O3/TiO2 molar ratio. Maleic acid was employed as an organic binder to unite Bi2O3 and TiO2 nanoparticles. The SEM, TEM, XRD and diffuse reflectance spectra were utilized to characterize the prepared Bi2O3/TiO2 nanoheterojunction. The nanocomposite exhibited unusual high photocatalytic activity in decomposing 2-propanol in gas phase and phenol in aqueous phase and, evolution of CO2 under visible light irradiation while the end members exhibited low photocatalytic activity. The composite was optimized to 5 mol% Bi2O3/TiO2. The remarkable high photocatalytic efficiency originates from the unique relative energy band position of Bi2O3 and TiO2 as well as the absorption of visible light by Bi2O3.
文摘In this paper, a detailed study was carried out on the PTFE reinforced with TiO2 and CaTiO3. The filler content of ceramic powder was a fixed value of 61 wt% and the content of CaTiO3 in PTFE matrix varied from 0 wt% to 16 wt% with a step size of 4 wt%. The effects of CaTiO3 loading on the density, moisture absorption, thermal expansion, microstructure and microwave dielectric properties were investigated. As CaTiO3 loading content increased from 0 wt% to 16 wt%, the thermal expansion initially displayed a sharp increase, and showed a slight enhancement when the content of CaTiO3 exceeded 12 wt%. The density experienced a continuous decrease with the addition of CaTiO3. The moisture absorption displayed a steady increase with the increasing CaTiO3 loading amount. The changing of dielectric constant (εr) and loss tangent (tanδ) were similar to that of the moisture absorption in a manner. Good dielectric properties with values of εr = 11.60, tanδ = 0.002 were obtained in the PTFE matrix with 16 wt% CaTiO3 and 45 wt% TiO2.
基金financially supported by the National Natural Science Foundation of China(Nos.51871199 and 61534001)。
文摘Bi2(Te,Se)3 alloys are conventional commercial thermoelectric materials for solid-state refrigeration around room temperature.In recent years,much attention has been paid to various advanced thermoelectric composite materials due to the unique thermoelectric properties.In this work,Bi2Se3/TiO2 composites were prepared by hot pressing the plate-like Bi2Se3 powders coated in situ with hydrolyzed hytetabutyl-n-butyl titanate(TNBT),and therefore numerous TiO2 in micrometer size could be formed on the interface of Bi2Se3 grains.The carrier concentration in Bi2Se3 matrix is optimized subject to the addition of n-type semiconductor TiO2,contributing to a significant improved power factor.In the meantime,the lattice thermal conductivity is also suppressed due to the enhanced phonon scattering at Bi2Se3/TiO2 interface and amorphous TiO2 particles.As a consequence,a peak figure of merit(zT)of 0.41 is obtained at 525 K in Bi2Se3/15 mol%TiO2 composites,nearly 50%augment over the pristine Bi2Se3 binary compound.
文摘TiAl3 particle reinforced pure Al composite has been made by direct reaction among molten Al, TiO2 and a flux. The composite exhibits high Synthetically properties. The strength and hardness are higher than those of pure Al matrix by 71.5% and 134% respectively However, the elongation is 20.36%, slightly lower than that of the Al matrix.
基金Project supported by the National Natural Science Foundation of China (Grant No. 20876125)the Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20096101110013)the Northwest University Graduate Cross-Discipline Funds (Grant Nos. 09YJC27,09YJC24,and 201031)
文摘The up-conversion luminescence composite NaYF4：Er3＋/TiO2 is prepared using the sol-gel method. The specimen has good crystallinity and two shapes, i.e., viereck and round, while the sizes of viereck and round particles are both micron-sized. The TiO2 has an anatase structure, while the NaYF4 has a hexagonal phase, which can be hardly obtained through the common sol-gel method. Due to the big particle size and the high crystallinity of pure NaYF4： Er3＋, the composite has a small specific surface area that is less than Degussa P25 TiO2. The NaYF4：Er3＋/TiO2 composite shows several emission peaks at 211, 237, and 251 nm under the excitation of 388 nm, at 395 nm and 411 nm under the excitation of 500 nm, and at 467, 481,492, and 508 nm under the excitation of 570 nm.
基金Supported by the National Natural Science Foundation of China under Grant Nos 11174137,11474215 and 21204058the Natural Science Foundation for the Youth of Jiangsu Province under Grant No BK20130284the Priority Academic Program Development of Jiangsu Higher Education Institutions
文摘Titanium dioxide （TiO2） loaded tungsten trioxide （WO3） composite films are prepared by an E-beam vapor system. Associated with the existence of a heterojunction at the interface of TiO2 and WO3, the prepared TiO2-WO3 composite film shows enhanced photocurrent density, four times than the pure WO3 film illuminated under xenon lamp, and higher incident-photon-to-current conversion e^ciency. By varying the initial TiO2 film thickness, such composite structures could be optimized to obtain the highest photocurrent density. We believe that thin TiO2 films improve the light response and increase the surface roughness of WO3 films. Furthermore, the existence of the heterojunction results in the e^cient charge carriers＇ separation, transfer process, and a lower recombination of electron-hole pairs, which is beneficial for the enhancement of photocurrent density.
文摘Al 2O 3-SiO 2-TiO 2-ZrO 2 supported membranes were prepar ed by Sol-Gel method. These composite ceramic membranes are level, even and no macro crack. There exist several crystalline phases such as Al 2O 3, TiO 2(a natase), Al 2SiO 5, and ZrO 2 in these membranes. Changing the molar ratio of Al∶Si∶Ti∶Zr,the kinds and content of crystal phases of composite membranes could be different, which may lead to a variety of microstructure of membranes. The surface nanoscale topography and microstructure of membranes were investiga ted by XRD,SEM,AFM,EPMA. The effects of additives and heat treatments on the sur face nanoscale topography and microstructure of composite ceramic membranes were also analyzed.
文摘TiB2-Al2O3 composite powders were produced by self-propagating high-temperature synthesis（SHS） method with reductive process from B2O3-TiO2-AI system. X-ray diffraction（XRD） and scanning electron microscopy（SEM） analyses show the presence of TiB2 and Al2O3 only in the composite powders produced by SHS. The powders are uniform and free-agglomerate. Transmission electron microscopy （TEM） and high resolution electron microscopy （HREM） observation of microstructure of the composite powders indicate that the interfaces of the TiB2-Al2O3 bond well, without any interfacial reaction products. It is proposed that the good interfacial bonding of the composite powders can be resulted from the TiB2 particles crystallizing and growing on the Al2O3 particles surface with surface defects acting as nucleation centers.
文摘The conductivities of polyethylene oxide (PEO)-based polymer electrolytes (PE) can be improved by the addition of inorganic inert powder. The composite polymer electrolytes (CPE) PEO10LiX (X=4ClO- or 322N(CFSO)-)-Li2TiO3 were prepared by solution casting with inorganic solid electrolyte Li2TiO3 powder as a filler. Results showed that the conductivities of PEO10LiClO4-3wt% Li2TiO3 and PEO10LiN(CF3SO2)2-10wt% Li2TiO3 at 30 ℃ were 8.6×10-6 and 5.6×10-5 S·cm-1, respectively. The conductivities of CPE increased with the decrease of filler抯 particle size. The ionic conduction mechanism analysis showed that there may be three conduction routes in the CPE, i.e., PEO bulk, polymer-filler interface and Li2TiO3 crystal.
