In order to reduce the friction coefficients and further improve the anti-wear properties of Ni-base alloy coatings reinforced by TiC particles,graphite/TiC/Ni-base alloy（GTN） coatings were prepared on the surface o...In order to reduce the friction coefficients and further improve the anti-wear properties of Ni-base alloy coatings reinforced by TiC particles,graphite/TiC/Ni-base alloy（GTN） coatings were prepared on the surface of 45 carbon steel.The effects of graphite content on the microstructure and tribological properties of the GTN coatings were investigated.The results show that the addition of graphite to the GTN coatings may greatly reduce the friction coefficients and improve their wear resistance.The 6.56GTN and 12.71GTN coatings exhibit excellent integrated properties of anti-friction and wear resistance under low and high loads,respectively.Under a low load,the wear mechanisms of the GTN coatings are mainly multi-plastic deformation with slight abrasive wear and gradually change into mixture of multi-plastic deformation,delamination and micro-cutting wear with the increase of graphite fraction.As the load increases,the main wear mechanisms gradually change from micro-cracks,micro-cutting and adhesive wear to micro-cutting and micro-fracture with the increase of graphite fraction.展开更多
Reinforcing metal matrix composites(MMCs)with nanophases of distinct characteristics is an effective strategy for utilizing their individual advantages and achieving superior properties of the composite.In this study,...Reinforcing metal matrix composites(MMCs)with nanophases of distinct characteristics is an effective strategy for utilizing their individual advantages and achieving superior properties of the composite.In this study,a combination of molecular level mixing(MLM),segment ball milling(SBM),and in-situ solid-phase reaction was employed to fabricate Cu matrix composites(TiC-CNT/Cu)reinforced with TiC decorated CNT(TiC@CNT)and in-situ nanoscale TiC particles.The HRTEM results revealed the epitaxial growth of interfacial TiC on the surface of CNT(i.e.,CNT(0002)//TiC(200),and the formation of a semi-coherent interface between TiC and Cu matrix,which can effectively enhance the interfacial bonding strength and optimize load transfer efficiency of CNT.The independent in-situ TiC nanoparticles got into the grain interior through grain boundary migration,thereby significantly enhancing both strain hardening capacity and strength of the composite by fully utilizing the Orowan strengthening mechanism.Moreover,the enhanced bonding strength of the interface can also effectively suppress crack initiation and propagation,thereby improving the fracture toughness of the composite.The TiC-CNT/Cu composite with 1.2 vol.%CNT exhibited a tensile strength of 372 MPa,achieving a super high strengthening efficiency of 270,while simultaneously maintaining a remarkable ductility of 21.2%.Furthermore,the impact toughness of the TiC-CNT/Cu composite exhibited a significant enhancement of 70.7%compared to that of the CNT/Cu composite,reaching an impressive value of 251 kJ/m^(2),thereby demonstrating exceptional fracture toughness.Fully exploiting the synergistic strengthening effect of different nanophases can be an effective way to improve the comprehensive properties of MMCs.展开更多
The Fe40Mn40Cr10Co10/TiC (volume fraction of TiC, 10%) composites were synthesized in combination of ball milling and spark plasma sintering (SPS) in the present work. Mechanical properties and wear resistance of the ...The Fe40Mn40Cr10Co10/TiC (volume fraction of TiC, 10%) composites were synthesized in combination of ball milling and spark plasma sintering (SPS) in the present work. Mechanical properties and wear resistance of the Fe40Mn40Cr10Co10/TiC composites were individually investigated. It was found that TiC particles homogenously distributed in the Fe40Mn40Cr10Co10/TiC composite after being sintered at 1373 K for 15 min. Meanwhile, grain refinement was observed in the as-sintered composite. Compared with the pure Fe40Mn40Cr10Co10 medium entropy alloy (MEA) matrix grain, addition of 10% TiC particles resulted in an increase in the compressive strength from 1.571 to 2.174 GPa, and the hardness from HV 320 to HV 872. Wear resistance results demonstrated that the friction coefficient, wear depth and width of the composite decreased in comparison with the Fe40Mn40Cr10Co10 MEA matrix. Excellent mechanical properties and wear resistance could offer the Fe40Mn40Cr10Co10/TiC composite a very promising candidate for engineering applications.展开更多
Different additions of BaC were introduced into TC4 to alter the microstructure and mechanical properties. The morphologies of reinforcements are related to the solidification paths. The refinement of lamellar spacing...Different additions of BaC were introduced into TC4 to alter the microstructure and mechanical properties. The morphologies of reinforcements are related to the solidification paths. The refinement of lamellar spacing 2 is based on the precipitation pattern of [3-phases. Microhardness, compression elastic modulus （Ec）, and elastic modulus of the matrix （Em） appear non-linear relationships with B4C additions. Due to the refinement of lamellar spacing with Hall-Petch-type relationships, and the solution strengthening of C on the α＋ β matrix, the effect of reinforcements on the mechanical properties will be more efficient when the additions of B4C are no more than 0.19 wt%. When the additions of B4C are more than 0.19 wt%, the efficiency will decrease.展开更多
Because of an unfortunate mistake during the production of this article,the Acknowledgements have been omitted.The Acknowledgements are added as follows:Sasan YAZDANI would like to thank the Scientific and Technologic...Because of an unfortunate mistake during the production of this article,the Acknowledgements have been omitted.The Acknowledgements are added as follows:Sasan YAZDANI would like to thank the Scientific and Technological Research Council of Turkey(TÜB˙ITAK)for receiving financial support for this work through the 2221 Fellowship Program for Visiting Scientists and Scientists on Sabbatical Leave(Grant ID:E 21514107-115.02-228864).Sasan YAZDANI also expresses his gratitude to Sahand University of Technology for granting him sabbatical leave to facilitate the completion of this research.展开更多
Ti-Fe-x TiC(x=0, 3, 6, 9, wt.%) composites were fabricated through low temperature ball milling of Ti, Fe and TiC powders, followed by spark plasma sintering. The results show that β-Ti, β-Ti-Fe, η-Ti4 Fe2 O0.4 and...Ti-Fe-x TiC(x=0, 3, 6, 9, wt.%) composites were fabricated through low temperature ball milling of Ti, Fe and TiC powders, followed by spark plasma sintering. The results show that β-Ti, β-Ti-Fe, η-Ti4 Fe2 O0.4 and TiC particles can be found in the composites. The microstructure can be obviously refined with increasing the content of TiC particles. The coefficient of friction(COF) decreases and the hardness increases with increasing the content of TiC particles. The adhesive wear is the dominant wear mechanism of all the Ti-Fe-x TiC composites. The Ti-Fe-6 TiC composite shows the best wear resistance, owing to the small size and high content of TiC particle as well as relatively fine microstructure. The wear rate of the Ti-Fe-6 TiC composite is as low as 1.869× 10-5 mm3/(N·m) and the COF is only 0.64. Therefore, TiC particle reinforced Ti-Fe based composites may be utilized as potential wear resistant materials.展开更多
The addition of ceramic reinforcements provides a promising approach to achieving high-performance magnesium matrix composites.In this work,AZ91D magnesium alloys and 2 wt.%TiC/AZ91D composites have been manufactured ...The addition of ceramic reinforcements provides a promising approach to achieving high-performance magnesium matrix composites.In this work,AZ91D magnesium alloys and 2 wt.%TiC/AZ91D composites have been manufactured by laser powder bed fusion(LPBF)with variations of laser processing parameters.The effect of TiC reinforcement addition on the laser absorption behaviors,forming quality,microstructure evolution and mechanical properties of the magnesium alloys is investigated.The TiC addition improves the interactions of laser with alloy powder and laser absorption rate of alloy powder,and decreases powder spatter of powder bed.The results show that high relative density of~99.4%and good surface roughness of~12μm are obtained for the LPBF-fabricated composites.The TiC addition promotes the precipitation of β-Mg_(17)Al_(12)in the alloys and the transformation of coarse columnar to fine equiaxed grains,where the grains are refined to~3.1μm.The TiC/AZ91D composites exhibit high microhardness of 114.6±2.5 HV_(0.2),high tensile strength of~345.0 MPa and a uniform elongation~4.1%.The improvement of tensile strength for the composites is ascribed to the combination of grain refinement strengthening and Orowan strengthening fromβ-Mg_(17)Al_(12)precipitates and Al_8Mn_5 nanoparticles.In the composites,the unmelted TiC particles can act as an anchor for the network structure of β-Mg_(17)Al_(12)precipitates,effectively impeding crack propagation and enhancing their performance.This work offers an insight to fabricating high-performance magnesium matrix composites by laser additive manufacturing.展开更多
FeAl/TiC composites were fabricated by hot pressing blended elemental powders. The effects of Ni-doping on thedensification and mechanical properties of the composites were studied. Results show that the density of th...FeAl/TiC composites were fabricated by hot pressing blended elemental powders. The effects of Ni-doping on thedensification and mechanical properties of the composites were studied. Results show that the density of the composites decreases with the content of TiC increasing, and the addition of Ni significantly improves the densificationprocess by enhancing mass transfer in the bonding phase. The mechanical properties of the composites are closelyrelated with their porosity. Besides increasing the density of the composites, the addition of Ni improves the mechanical properties by other three effects: solution-strengthening the bonding phase, strengthening the FeAI-TiC interfaceand increasing ductile fracture in FeAl phase.展开更多
In this study, La2O3 was investigated as an additive to TiC/W composites. The composites were prepared by vacuum hot pressing, and the microstructure and mechanical properties of the composites were investigated. Expe...In this study, La2O3 was investigated as an additive to TiC/W composites. The composites were prepared by vacuum hot pressing, and the microstructure and mechanical properties of the composites were investigated. Experimental results show that the grain size of the TiC/W composites is reduced by TiC particles. When 0.5 wt.% La2O3 is added to the composites, the grain size is reduced further. According to TEM analysis, La2O3 can alleviate the aggregation of TiC particles. With La2O3 addition, the relative density of the TiC/W composites can be improved from 95.1% to 96.5%. The hardness and elastic modulus of the TiC/W ＋ 0.5 wt.% La2O3 composite are little improved, but the flexural strength and the fracture toughness increase to 796 MPa and 10.07 MPa·m^1/2 respectively, which are higher than those of the TiC/W composites.展开更多
The effects of the reactive temperature, time and the cooling rate of an Fe Ti C alloy melt on the microstructures and mechanical properties of in situ TiC p/Fe composites were investigated. The results show that the ...The effects of the reactive temperature, time and the cooling rate of an Fe Ti C alloy melt on the microstructures and mechanical properties of in situ TiC p/Fe composites were investigated. The results show that the hardness and impact toughness of the prepared composites increase with increasing the reactive temperature, because more and finer TiC particles are formed in the higher temperature melt. However, after the TiC synthesis reaction in the melt completed, the impact toughness of the composites will decrease if the melt reactive time is further prolonged, owing to the coarsening of the formed TiC particles. Under the present experimental condition, the cooling rate of the melt containing dispersions has little influence on the number, size and distribution of the particles in the composites.展开更多
Pressureless melt infiltration is an economic route f or preparation of high-density ceramic/melt composites. In this study, the Fe40 Al iron aluminide intermetallic, a low cost material of excellent oxidation and cor...Pressureless melt infiltration is an economic route f or preparation of high-density ceramic/melt composites. In this study, the Fe40 Al iron aluminide intermetallic, a low cost material of excellent oxidation and corrosion resistance, was used as binder for fabricating Fe40Al/TiC composites b y pressureless melt infiltration. The wetting ability of liquid Fe40Al in porous TiC pre-form was studied by in-situ monitoring the melting and infiltration p rocess. The infiltration ability was investigated by observing the distance of l iquid Fe40Al intrusion in porous TiC pre-forms at different infiltration temper atures and times by using optical microscope. Porous TiC per-forms with density of 60%～88%TD (theoretical density), prepared under pre-defined sintering temp e rature cycles, were used for fabricating Fe40Al/TiC composites in the range of 1 2%～40% metal content by volume. Almost full dense Fe40Al/TiC composites were su c cessfully fabricated by this technique. Liquid Fe40Al exhibited excellent infilt ration ability, the distance of complete intrusion of liquid Fe40Al in the TiC s intered pre-form with density of 88%TD was over 7 mm after 5 min at the inf iltration temperature of 1 450 ℃. Microstructural observation by SEM and TEM also showed that liquid Fe40Al filled the very narrow gaps among TiC particles, the interfaces of TiC particles and F e40Al plastic ligaments being metallurgical bonded. TEM revealed that high densi ty of dislocations formed in Fe40Al ligaments during solidification, which favor the mechanical properties. Ti decomposed from TiC particles and dissolved into Fe40Al during infiltration. According to the compositional analysis of TEM-EDS, the concentration of Ti in Fe40Al ranges at 1at%～4at% depending on composite f a bricating conditions and the distance from the measuring point to the closest Ti C particles. XRD analysis indicated that the composites were composed of two pha ses, the original TiC and Fe 0.4Al 0.6 intermetallic. No new phase formed during infiltration, but the lattice parameter of Fe 0.4Al 0.6 was expended due to the Ti in the solid solution.展开更多
The electromagnetic and microwave absorbing properties of FeCoB powder composites prepared by sin- gle-roller melt-spinning and mechanical milling processes were investigated in this paper. The result indicates that t...The electromagnetic and microwave absorbing properties of FeCoB powder composites prepared by sin- gle-roller melt-spinning and mechanical milling processes were investigated in this paper. The result indicates that the flake-like powders are obtained. As milling time increases, the flake-like powder particles tend to agglomerate, causing the flake-like powders decrease gradually. The milling time plays an important role in the electromagnetic parameters which relates to the shape and size of the powder particles. The calculation shows that the sample milled for 6 h could achieve an optimal reflection loss of -11.5 dB at 5.8 GHz, with mass fraction of 83 % and a matching thickness of 1.8 mm. The result also indicates that the microwave absorbing properties of the FeCoB powder composites are adjustable by changing their thickness, and can be applied as a thinner microwave absorbing material in the range of 2-8 GHz.展开更多
Cross-linkedβ-cyclodextrin polymer/Fe3O4 composite nanoparticles with core-shell structures were prepared via cross linking reaction on the surface of carboxymethylβ-cyclodextrin（CM-β-CD） modified Fe3O4 nanoparti...Cross-linkedβ-cyclodextrin polymer/Fe3O4 composite nanoparticles with core-shell structures were prepared via cross linking reaction on the surface of carboxymethylβ-cyclodextrin（CM-β-CD） modified Fe3O4 nanoparticles inβ-cyclodextrin alkaline solution by using epichlorohydrin as crosslinking agent.The morphology,structure and magnetic properties of the prepared composite nanoparticles were investigated by transmission electron microscopy（TEM）,Fourier transform infrared（FTIR） spectrometry,X-ray diffraction（XRD） measurement,thermogravimetric analysis（TGA） and Vibrating sample magnetometry （VSM）,respectively.展开更多
In situ TiC particles-reinforced FeCrNiCu high-entropy alloy matrix composites were prepared by vacuum induction melting method.The reaction mechanisms of the mixed powder(Ti,Cu and C)were analyzed,and the mechanical ...In situ TiC particles-reinforced FeCrNiCu high-entropy alloy matrix composites were prepared by vacuum induction melting method.The reaction mechanisms of the mixed powder(Ti,Cu and C)were analyzed,and the mechanical properties of resultant composites were determined.Cu4Tiwere formed in the reaction of Cu and Ti when the temperature rose to 1160 K.With the temperature further increased to 1182 K,newly formed Cu4Tireacted with C to give rise to TiC particles as reinforcement agents.The apparent activation energy for these two reactions was calculated to be 578.7 kJ/mol and 1443.2 kJ/mol,respectively.The hardness,tensile yield strength and ultimate tensile strength of the 15 vol%TiC/FeCrNiCu composite are 797.3 HV,605.1 MPa and 769.2 MPa,respectively,representing an increase by 126.9%,65.9%and 36.0%as compared to the FeCrNiCu high-entropy base alloy at room temperature.However,the elongation-to-failure is reduced from 21.5 to 6.1%with the formation of TiC particles.It was revealed that Orowan mechanism,dislocation strengthening and load-bearing effect are key factors responsible for a marked increase in the hardness and strength of the high-entropy alloy matrix composites.展开更多
The NiAl–TiC–TiB2 composites were processed by self-propagating high-temperature synthesis（SHS） method using raw powders of Ni, Al, Ti, B4 C, TiC, and TiB2, and their microstructure and micro-hardness were investi...The NiAl–TiC–TiB2 composites were processed by self-propagating high-temperature synthesis（SHS） method using raw powders of Ni, Al, Ti, B4 C, TiC, and TiB2, and their microstructure and micro-hardness were investigated. The TiC–TiB2 in NiAl matrix, with contents from 10 to 30 wt%, emerged with the use of two methods： in situ formed and externally added. The results show that all final products are composed of three phases of NiAl, TiC, and TiB2. The microstructures of NiAl–TiC–TiB2 composites with in situ-formed TiC and TiB2 are fine, and all the three phases are distributed uniformly. The grains of NiAl matrix in the composites have been greatly refined, and the micro-hardness of NiAl increases from 381 HV100 to 779 HV100. However, the microstructures of NiAl–TiC–TiB2 composites with externally added TiC and TiB2 are coarse and inhomogeneous, with severe agglomeration of TiC and TiB2 particles. The samples containing externally added 30 wt% TiC–TiB2attain the micro-hardness of 485 HV100. The microstructure evolution and fracture mode of the two kinds of NiAl–TiC–TiB2 composites are different.展开更多
The base structure of in situ TiCp/Fe composites fabricated under industrial condition was changed by different heat treatments.Erosive wear tests were carried out and the results were compared with that of wear-resis...The base structure of in situ TiCp/Fe composites fabricated under industrial condition was changed by different heat treatments.Erosive wear tests were carried out and the results were compared with that of wear-resistant white cast iron.The results suggest that the wear resistance of the in situ TiCp/Fe composite is higher than that of wear-resistant white cast iron under the sand erosive wear condition.The wear mechanism of the wear-resistant white cast iron was a cycle process that base surface was worn and carbides were exposed,then carbides was broken and wear pits appeared.While the wear mechanism of in situ TiCp/Fe composite was a cycle process that base surface was worn and TiC grains were exposed and dropped.The wear resistance of in situ TiCp/Fe composite was lower than that of wear-resistant white cast iron under the slurry erosive wear condition.Under such circumstance,the material was not only undergone erosive wear but also electrochemistry erosion due to the contact with water in the medium.The wear behaviours can be a combination of two kinds of wear and the sand erosive wear is worse than slurry erosive wear.展开更多
By means of an inherent elevated-temperature of poured liquid steel,a Ti-C-30wt%Fe preform,which was pre-placed in a mould cavity,was directly ignited and a combustion synthesis reaction took place.As a result,a TiC-F...By means of an inherent elevated-temperature of poured liquid steel,a Ti-C-30wt%Fe preform,which was pre-placed in a mould cavity,was directly ignited and a combustion synthesis reaction took place.As a result,a TiC-Fe cermet coating with a thickness of about 10mm was simultaneously synthesized on the solidified steel matrix.The synthesized coating exhibits a feature of graded composite structure,in which both the amount and size of TiC particles decrease gradually with an increasing distance from the furface of the coating.Moreover,by a proper casting technique,the pores formed during the combustion synthesis of the preform could be centrally distributed in 2-3mm in outer layer of the coating.When this outer porous layer was worn off,the rest coating with a thickness of about 8mm possesses a dense structure and a high abrasive wear resistance.展开更多
The Fe-based WC composite coatings were clad on Q235 steel by double-pass plasma cladding method,in which the WC-Co(WC covered with cobalt:78wt%WC,12wt%Co)doping was about 10wt%,20wt%and 40wt%,respectively.The microst...The Fe-based WC composite coatings were clad on Q235 steel by double-pass plasma cladding method,in which the WC-Co(WC covered with cobalt:78wt%WC,12wt%Co)doping was about 10wt%,20wt%and 40wt%,respectively.The microstructure and wear performance of the composite coatings were investigated by X-ray diffraction(XRD),scanning electron microscope(SEM),energy dispersive spectrometer(EDS)and ball-disc wear tests.The results show that the clad coatings contain mainly?-Fe,WC and carbides(Cr23C6,Fe3W3C-Fe4W2C)phases and the precipitation of carbides increases with the increase of WC-Co doping content.The WC-Co doping content has an obvious effect on the microstructure of the clad coatings.For the clad coatings with low WC-Co doping,the microstructure gradually transforms from planar crystal at the interface of substrate/coating to cell/dendritic crystal at the middle and the upper portion of the coatings.But there are a number of fishbone-like structure at the middle and the upper portion of clad coating with 40wt%WC-Co doping.The microstructure at the top is smaller than that at the bottom for all the coatings.The maximum of hardness of the clad coatings is 72.3HRC which is about 6.9 as much as the hardness of Q235 steel substrate.The composite coatings have good wear resistance due to the reinforcement of carbide particles and the strong bonding between carbide particles and ferroalloy.The suitable increase of WC-Co doping content can improve the wear resistance of the composite coatings.展开更多
W-30 wt%Cu and TiC-50 wt%Ag were successfully synthesized by a novel simplified pretreatment followed by electroless plating.The 0 wt%TiC,0.5 wt%TiC,and 0.5 wt%TiC-0.5 wt%Ag composite powders were added to W-30 wt%Cu ...W-30 wt%Cu and TiC-50 wt%Ag were successfully synthesized by a novel simplified pretreatment followed by electroless plating.The 0 wt%TiC,0.5 wt%TiC,and 0.5 wt%TiC-0.5 wt%Ag composite powders were added to W-30 wt%Cu composite powders by blending,and then reduced.The reduced W-30 Cu,W-30 Cu/0.5 TiC,and W-30 Cu-0.5 Ag/0.5 TiC composite powders were then compacted and sintered at 1300℃in protective hydrogen for 60 min.The phase and morphology of the composite powders and materials were analyzed using X-ray diffraction and field emission scanning electron microscopy.The relative density,electrical conductivity,and hardness of the sintered samples were examined.Results showed that W-30 Cu and TiC-Ag composite powders with uniform structure were obtained using simplified pretreatment followed by electroless plating.The addition of TiC particles can significantly increase the compressive strength and hardness of the W-30 Cu composite material but decrease the electrical conductivity.Next,0.5 wt%Ag was added to prepare W-30 Cu-0.5 Ag/TiC composites with excellent electrical conductivity.The electrical conductivity of these composites(61.2%)is higher than that in the national standard(the imaginary line denotes electrical conductivity of GB IACS 42%)of 45.7%.展开更多
文摘In order to reduce the friction coefficients and further improve the anti-wear properties of Ni-base alloy coatings reinforced by TiC particles,graphite/TiC/Ni-base alloy（GTN） coatings were prepared on the surface of 45 carbon steel.The effects of graphite content on the microstructure and tribological properties of the GTN coatings were investigated.The results show that the addition of graphite to the GTN coatings may greatly reduce the friction coefficients and improve their wear resistance.The 6.56GTN and 12.71GTN coatings exhibit excellent integrated properties of anti-friction and wear resistance under low and high loads,respectively.Under a low load,the wear mechanisms of the GTN coatings are mainly multi-plastic deformation with slight abrasive wear and gradually change into mixture of multi-plastic deformation,delamination and micro-cutting wear with the increase of graphite fraction.As the load increases,the main wear mechanisms gradually change from micro-cracks,micro-cutting and adhesive wear to micro-cutting and micro-fracture with the increase of graphite fraction.
基金financially supported by the National Natural Science Foundation of China(No.52371136)the Yunnan Provincial Science and Technology Department(No.202202AG050004).
文摘Reinforcing metal matrix composites(MMCs)with nanophases of distinct characteristics is an effective strategy for utilizing their individual advantages and achieving superior properties of the composite.In this study,a combination of molecular level mixing(MLM),segment ball milling(SBM),and in-situ solid-phase reaction was employed to fabricate Cu matrix composites(TiC-CNT/Cu)reinforced with TiC decorated CNT(TiC@CNT)and in-situ nanoscale TiC particles.The HRTEM results revealed the epitaxial growth of interfacial TiC on the surface of CNT(i.e.,CNT(0002)//TiC(200),and the formation of a semi-coherent interface between TiC and Cu matrix,which can effectively enhance the interfacial bonding strength and optimize load transfer efficiency of CNT.The independent in-situ TiC nanoparticles got into the grain interior through grain boundary migration,thereby significantly enhancing both strain hardening capacity and strength of the composite by fully utilizing the Orowan strengthening mechanism.Moreover,the enhanced bonding strength of the interface can also effectively suppress crack initiation and propagation,thereby improving the fracture toughness of the composite.The TiC-CNT/Cu composite with 1.2 vol.%CNT exhibited a tensile strength of 372 MPa,achieving a super high strengthening efficiency of 270,while simultaneously maintaining a remarkable ductility of 21.2%.Furthermore,the impact toughness of the TiC-CNT/Cu composite exhibited a significant enhancement of 70.7%compared to that of the CNT/Cu composite,reaching an impressive value of 251 kJ/m^(2),thereby demonstrating exceptional fracture toughness.Fully exploiting the synergistic strengthening effect of different nanophases can be an effective way to improve the comprehensive properties of MMCs.
基金Project(51404302)supported by the National Natural Science Foundation of China
文摘The Fe40Mn40Cr10Co10/TiC (volume fraction of TiC, 10%) composites were synthesized in combination of ball milling and spark plasma sintering (SPS) in the present work. Mechanical properties and wear resistance of the Fe40Mn40Cr10Co10/TiC composites were individually investigated. It was found that TiC particles homogenously distributed in the Fe40Mn40Cr10Co10/TiC composite after being sintered at 1373 K for 15 min. Meanwhile, grain refinement was observed in the as-sintered composite. Compared with the pure Fe40Mn40Cr10Co10 medium entropy alloy (MEA) matrix grain, addition of 10% TiC particles resulted in an increase in the compressive strength from 1.571 to 2.174 GPa, and the hardness from HV 320 to HV 872. Wear resistance results demonstrated that the friction coefficient, wear depth and width of the composite decreased in comparison with the Fe40Mn40Cr10Co10 MEA matrix. Excellent mechanical properties and wear resistance could offer the Fe40Mn40Cr10Co10/TiC composite a very promising candidate for engineering applications.
基金financially supported by the National Basic Research Program of China (No.2012CB619600)Shanghai Academy of Spaceflight-Joint Research Centre of Shanghai Jiaotong University advanced aerospace technology (No.USCAST2012-14)+1 种基金Shanghai Science and Technology Committee (No.12XD1402800)the Dawn Program of Shanghai Education Commission (No.10SG15)
文摘Different additions of BaC were introduced into TC4 to alter the microstructure and mechanical properties. The morphologies of reinforcements are related to the solidification paths. The refinement of lamellar spacing 2 is based on the precipitation pattern of [3-phases. Microhardness, compression elastic modulus （Ec）, and elastic modulus of the matrix （Em） appear non-linear relationships with B4C additions. Due to the refinement of lamellar spacing with Hall-Petch-type relationships, and the solution strengthening of C on the α＋ β matrix, the effect of reinforcements on the mechanical properties will be more efficient when the additions of B4C are no more than 0.19 wt%. When the additions of B4C are more than 0.19 wt%, the efficiency will decrease.
文摘Because of an unfortunate mistake during the production of this article,the Acknowledgements have been omitted.The Acknowledgements are added as follows:Sasan YAZDANI would like to thank the Scientific and Technological Research Council of Turkey(TÜB˙ITAK)for receiving financial support for this work through the 2221 Fellowship Program for Visiting Scientists and Scientists on Sabbatical Leave(Grant ID:E 21514107-115.02-228864).Sasan YAZDANI also expresses his gratitude to Sahand University of Technology for granting him sabbatical leave to facilitate the completion of this research.
基金financial support from the National Key Fundamental Research and Development Project of China (2014CB644002)。
文摘Ti-Fe-x TiC(x=0, 3, 6, 9, wt.%) composites were fabricated through low temperature ball milling of Ti, Fe and TiC powders, followed by spark plasma sintering. The results show that β-Ti, β-Ti-Fe, η-Ti4 Fe2 O0.4 and TiC particles can be found in the composites. The microstructure can be obviously refined with increasing the content of TiC particles. The coefficient of friction(COF) decreases and the hardness increases with increasing the content of TiC particles. The adhesive wear is the dominant wear mechanism of all the Ti-Fe-x TiC composites. The Ti-Fe-6 TiC composite shows the best wear resistance, owing to the small size and high content of TiC particle as well as relatively fine microstructure. The wear rate of the Ti-Fe-6 TiC composite is as low as 1.869× 10-5 mm3/(N·m) and the COF is only 0.64. Therefore, TiC particle reinforced Ti-Fe based composites may be utilized as potential wear resistant materials.
基金supported by the National Natural Science Foundation of China(52205382,52225503)National Key Research and Development Program(2023YFB4603300)+1 种基金Key Research and Development Program of Jiangsu Province(BZ2024019,BE2022069)International Joint Laboratory of Sustainable Manufacturing,Ministry of Education and the Fundamental Research Funds for the Central Universities(NG2024014,XCA2300501)。
文摘The addition of ceramic reinforcements provides a promising approach to achieving high-performance magnesium matrix composites.In this work,AZ91D magnesium alloys and 2 wt.%TiC/AZ91D composites have been manufactured by laser powder bed fusion(LPBF)with variations of laser processing parameters.The effect of TiC reinforcement addition on the laser absorption behaviors,forming quality,microstructure evolution and mechanical properties of the magnesium alloys is investigated.The TiC addition improves the interactions of laser with alloy powder and laser absorption rate of alloy powder,and decreases powder spatter of powder bed.The results show that high relative density of~99.4%and good surface roughness of~12μm are obtained for the LPBF-fabricated composites.The TiC addition promotes the precipitation of β-Mg_(17)Al_(12)in the alloys and the transformation of coarse columnar to fine equiaxed grains,where the grains are refined to~3.1μm.The TiC/AZ91D composites exhibit high microhardness of 114.6±2.5 HV_(0.2),high tensile strength of~345.0 MPa and a uniform elongation~4.1%.The improvement of tensile strength for the composites is ascribed to the combination of grain refinement strengthening and Orowan strengthening fromβ-Mg_(17)Al_(12)precipitates and Al_8Mn_5 nanoparticles.In the composites,the unmelted TiC particles can act as an anchor for the network structure of β-Mg_(17)Al_(12)precipitates,effectively impeding crack propagation and enhancing their performance.This work offers an insight to fabricating high-performance magnesium matrix composites by laser additive manufacturing.
基金This work was supported by Hunan Provincial Natural Science Foundation.
文摘FeAl/TiC composites were fabricated by hot pressing blended elemental powders. The effects of Ni-doping on thedensification and mechanical properties of the composites were studied. Results show that the density of the composites decreases with the content of TiC increasing, and the addition of Ni significantly improves the densificationprocess by enhancing mass transfer in the bonding phase. The mechanical properties of the composites are closelyrelated with their porosity. Besides increasing the density of the composites, the addition of Ni improves the mechanical properties by other three effects: solution-strengthening the bonding phase, strengthening the FeAI-TiC interfaceand increasing ductile fracture in FeAl phase.
基金financially supported by the Youth-Innova-tion-Community Fund of Hefei University of Technology (No. 103-037016)the Collaboration Project with the Institute of Plasma Physics, Chinese Academy of Sciences (No.103-413361)
文摘In this study, La2O3 was investigated as an additive to TiC/W composites. The composites were prepared by vacuum hot pressing, and the microstructure and mechanical properties of the composites were investigated. Experimental results show that the grain size of the TiC/W composites is reduced by TiC particles. When 0.5 wt.% La2O3 is added to the composites, the grain size is reduced further. According to TEM analysis, La2O3 can alleviate the aggregation of TiC particles. With La2O3 addition, the relative density of the TiC/W composites can be improved from 95.1% to 96.5%. The hardness and elastic modulus of the TiC/W ＋ 0.5 wt.% La2O3 composite are little improved, but the flexural strength and the fracture toughness increase to 796 MPa and 10.07 MPa·m^1/2 respectively, which are higher than those of the TiC/W composites.
文摘The effects of the reactive temperature, time and the cooling rate of an Fe Ti C alloy melt on the microstructures and mechanical properties of in situ TiC p/Fe composites were investigated. The results show that the hardness and impact toughness of the prepared composites increase with increasing the reactive temperature, because more and finer TiC particles are formed in the higher temperature melt. However, after the TiC synthesis reaction in the melt completed, the impact toughness of the composites will decrease if the melt reactive time is further prolonged, owing to the coarsening of the formed TiC particles. Under the present experimental condition, the cooling rate of the melt containing dispersions has little influence on the number, size and distribution of the particles in the composites.
文摘Pressureless melt infiltration is an economic route f or preparation of high-density ceramic/melt composites. In this study, the Fe40 Al iron aluminide intermetallic, a low cost material of excellent oxidation and corrosion resistance, was used as binder for fabricating Fe40Al/TiC composites b y pressureless melt infiltration. The wetting ability of liquid Fe40Al in porous TiC pre-form was studied by in-situ monitoring the melting and infiltration p rocess. The infiltration ability was investigated by observing the distance of l iquid Fe40Al intrusion in porous TiC pre-forms at different infiltration temper atures and times by using optical microscope. Porous TiC per-forms with density of 60%～88%TD (theoretical density), prepared under pre-defined sintering temp e rature cycles, were used for fabricating Fe40Al/TiC composites in the range of 1 2%～40% metal content by volume. Almost full dense Fe40Al/TiC composites were su c cessfully fabricated by this technique. Liquid Fe40Al exhibited excellent infilt ration ability, the distance of complete intrusion of liquid Fe40Al in the TiC s intered pre-form with density of 88%TD was over 7 mm after 5 min at the inf iltration temperature of 1 450 ℃. Microstructural observation by SEM and TEM also showed that liquid Fe40Al filled the very narrow gaps among TiC particles, the interfaces of TiC particles and F e40Al plastic ligaments being metallurgical bonded. TEM revealed that high densi ty of dislocations formed in Fe40Al ligaments during solidification, which favor the mechanical properties. Ti decomposed from TiC particles and dissolved into Fe40Al during infiltration. According to the compositional analysis of TEM-EDS, the concentration of Ti in Fe40Al ranges at 1at%～4at% depending on composite f a bricating conditions and the distance from the measuring point to the closest Ti C particles. XRD analysis indicated that the composites were composed of two pha ses, the original TiC and Fe 0.4Al 0.6 intermetallic. No new phase formed during infiltration, but the lattice parameter of Fe 0.4Al 0.6 was expended due to the Ti in the solid solution.
基金financially supported by the National Hi-tech R&D Project Supporting Programs Funded by Ministry of Science&Technology of China(No.2012AA063202)the National Natural Science Foundation of China(Nos.50972013,50802008,and 51004011)+1 种基金the National Key Project of Scientific and Technical Supporting Programs Funded by Ministry of Science&Technology of China(Nos.2012BAC02B01,2012BAC12B05,2011BAE13B07,and 2011BAC10B02)the Guangdong Province&Ministry of Education Industry-Study-Research United Project(No.2009A090100017)
文摘The electromagnetic and microwave absorbing properties of FeCoB powder composites prepared by sin- gle-roller melt-spinning and mechanical milling processes were investigated in this paper. The result indicates that the flake-like powders are obtained. As milling time increases, the flake-like powder particles tend to agglomerate, causing the flake-like powders decrease gradually. The milling time plays an important role in the electromagnetic parameters which relates to the shape and size of the powder particles. The calculation shows that the sample milled for 6 h could achieve an optimal reflection loss of -11.5 dB at 5.8 GHz, with mass fraction of 83 % and a matching thickness of 1.8 mm. The result also indicates that the microwave absorbing properties of the FeCoB powder composites are adjustable by changing their thickness, and can be applied as a thinner microwave absorbing material in the range of 2-8 GHz.
基金financially supported by the Guangdong Natural Science Foundation(No.020891)
文摘Cross-linkedβ-cyclodextrin polymer/Fe3O4 composite nanoparticles with core-shell structures were prepared via cross linking reaction on the surface of carboxymethylβ-cyclodextrin（CM-β-CD） modified Fe3O4 nanoparticles inβ-cyclodextrin alkaline solution by using epichlorohydrin as crosslinking agent.The morphology,structure and magnetic properties of the prepared composite nanoparticles were investigated by transmission electron microscopy（TEM）,Fourier transform infrared（FTIR） spectrometry,X-ray diffraction（XRD） measurement,thermogravimetric analysis（TGA） and Vibrating sample magnetometry （VSM）,respectively.
基金financially supported by the National Natural Science Foundation of China(Nos.51571118 and 51371098)Jiangsu Province Science and Technology Plan Project(No.BE2018753/KJ185629)。
文摘In situ TiC particles-reinforced FeCrNiCu high-entropy alloy matrix composites were prepared by vacuum induction melting method.The reaction mechanisms of the mixed powder(Ti,Cu and C)were analyzed,and the mechanical properties of resultant composites were determined.Cu4Tiwere formed in the reaction of Cu and Ti when the temperature rose to 1160 K.With the temperature further increased to 1182 K,newly formed Cu4Tireacted with C to give rise to TiC particles as reinforcement agents.The apparent activation energy for these two reactions was calculated to be 578.7 kJ/mol and 1443.2 kJ/mol,respectively.The hardness,tensile yield strength and ultimate tensile strength of the 15 vol%TiC/FeCrNiCu composite are 797.3 HV,605.1 MPa and 769.2 MPa,respectively,representing an increase by 126.9%,65.9%and 36.0%as compared to the FeCrNiCu high-entropy base alloy at room temperature.However,the elongation-to-failure is reduced from 21.5 to 6.1%with the formation of TiC particles.It was revealed that Orowan mechanism,dislocation strengthening and load-bearing effect are key factors responsible for a marked increase in the hardness and strength of the high-entropy alloy matrix composites.
基金financially supported by the National Natural Science Foundation of China(Nos.51072104 and 51272141)Tai Shan Scholars Project of Shandong Province,China(No.ts20110828)
文摘The NiAl–TiC–TiB2 composites were processed by self-propagating high-temperature synthesis（SHS） method using raw powders of Ni, Al, Ti, B4 C, TiC, and TiB2, and their microstructure and micro-hardness were investigated. The TiC–TiB2 in NiAl matrix, with contents from 10 to 30 wt%, emerged with the use of two methods： in situ formed and externally added. The results show that all final products are composed of three phases of NiAl, TiC, and TiB2. The microstructures of NiAl–TiC–TiB2 composites with in situ-formed TiC and TiB2 are fine, and all the three phases are distributed uniformly. The grains of NiAl matrix in the composites have been greatly refined, and the micro-hardness of NiAl increases from 381 HV100 to 779 HV100. However, the microstructures of NiAl–TiC–TiB2 composites with externally added TiC and TiB2 are coarse and inhomogeneous, with severe agglomeration of TiC and TiB2 particles. The samples containing externally added 30 wt% TiC–TiB2attain the micro-hardness of 485 HV100. The microstructure evolution and fracture mode of the two kinds of NiAl–TiC–TiB2 composites are different.
文摘The base structure of in situ TiCp/Fe composites fabricated under industrial condition was changed by different heat treatments.Erosive wear tests were carried out and the results were compared with that of wear-resistant white cast iron.The results suggest that the wear resistance of the in situ TiCp/Fe composite is higher than that of wear-resistant white cast iron under the sand erosive wear condition.The wear mechanism of the wear-resistant white cast iron was a cycle process that base surface was worn and carbides were exposed,then carbides was broken and wear pits appeared.While the wear mechanism of in situ TiCp/Fe composite was a cycle process that base surface was worn and TiC grains were exposed and dropped.The wear resistance of in situ TiCp/Fe composite was lower than that of wear-resistant white cast iron under the slurry erosive wear condition.Under such circumstance,the material was not only undergone erosive wear but also electrochemistry erosion due to the contact with water in the medium.The wear behaviours can be a combination of two kinds of wear and the sand erosive wear is worse than slurry erosive wear.
基金FinanciallysupportedbytheNationalNaturalScienceFoundationofChina (No .5 0 2 76 0 2 3)
文摘By means of an inherent elevated-temperature of poured liquid steel,a Ti-C-30wt%Fe preform,which was pre-placed in a mould cavity,was directly ignited and a combustion synthesis reaction took place.As a result,a TiC-Fe cermet coating with a thickness of about 10mm was simultaneously synthesized on the solidified steel matrix.The synthesized coating exhibits a feature of graded composite structure,in which both the amount and size of TiC particles decrease gradually with an increasing distance from the furface of the coating.Moreover,by a proper casting technique,the pores formed during the combustion synthesis of the preform could be centrally distributed in 2-3mm in outer layer of the coating.When this outer porous layer was worn off,the rest coating with a thickness of about 8mm possesses a dense structure and a high abrasive wear resistance.
基金Fundamental Research Funds for the Central Universities(2009B16214)China Postdoctoral Science Foundation funded project(20100481079)Scientific Research Start-up Fund Project of Hohai University(20080403)
文摘The Fe-based WC composite coatings were clad on Q235 steel by double-pass plasma cladding method,in which the WC-Co(WC covered with cobalt:78wt%WC,12wt%Co)doping was about 10wt%,20wt%and 40wt%,respectively.The microstructure and wear performance of the composite coatings were investigated by X-ray diffraction(XRD),scanning electron microscope(SEM),energy dispersive spectrometer(EDS)and ball-disc wear tests.The results show that the clad coatings contain mainly?-Fe,WC and carbides(Cr23C6,Fe3W3C-Fe4W2C)phases and the precipitation of carbides increases with the increase of WC-Co doping content.The WC-Co doping content has an obvious effect on the microstructure of the clad coatings.For the clad coatings with low WC-Co doping,the microstructure gradually transforms from planar crystal at the interface of substrate/coating to cell/dendritic crystal at the middle and the upper portion of the coatings.But there are a number of fishbone-like structure at the middle and the upper portion of clad coating with 40wt%WC-Co doping.The microstructure at the top is smaller than that at the bottom for all the coatings.The maximum of hardness of the clad coatings is 72.3HRC which is about 6.9 as much as the hardness of Q235 steel substrate.The composite coatings have good wear resistance due to the reinforcement of carbide particles and the strong bonding between carbide particles and ferroalloy.The suitable increase of WC-Co doping content can improve the wear resistance of the composite coatings.
基金Funded by the National Magnetic Confinement Fusion Program(No.2014GB121001)
文摘W-30 wt%Cu and TiC-50 wt%Ag were successfully synthesized by a novel simplified pretreatment followed by electroless plating.The 0 wt%TiC,0.5 wt%TiC,and 0.5 wt%TiC-0.5 wt%Ag composite powders were added to W-30 wt%Cu composite powders by blending,and then reduced.The reduced W-30 Cu,W-30 Cu/0.5 TiC,and W-30 Cu-0.5 Ag/0.5 TiC composite powders were then compacted and sintered at 1300℃in protective hydrogen for 60 min.The phase and morphology of the composite powders and materials were analyzed using X-ray diffraction and field emission scanning electron microscopy.The relative density,electrical conductivity,and hardness of the sintered samples were examined.Results showed that W-30 Cu and TiC-Ag composite powders with uniform structure were obtained using simplified pretreatment followed by electroless plating.The addition of TiC particles can significantly increase the compressive strength and hardness of the W-30 Cu composite material but decrease the electrical conductivity.Next,0.5 wt%Ag was added to prepare W-30 Cu-0.5 Ag/TiC composites with excellent electrical conductivity.The electrical conductivity of these composites(61.2%)is higher than that in the national standard(the imaginary line denotes electrical conductivity of GB IACS 42%)of 45.7%.
