Inorganic materials can solve transportable and on-site hydrolytic hydrogen generation issues.CaH_(2)/(Al/Si)composites are preferable due to their notable chemical properties.However,these composites require pretreat...Inorganic materials can solve transportable and on-site hydrolytic hydrogen generation issues.CaH_(2)/(Al/Si)composites are preferable due to their notable chemical properties.However,these composites require pretreatments,an inert environment,and long hours of physical ball milling for high homogeneity and synergistic effects.CaH_(2)also inhibits the hydrolysis reaction by forming its products on the Al/Si surface,which hinders the direct utilization of composites.This work represents the first investigation of NaH-CaH_(2)(Al/Si)fuel composites,which greatly overcome these limitations and can be directly used for on-site hydrogen generation and proton exchange membrane(PEM)fuel cells.The NaH-CaH_(2)(Al/Si)fuel composites were prepared by using a straightforward mixing method with variable composition ratios,showing high H_(2)yield and fuel cell(FC)performance.NaH addition provides the bridge effect,which opens up a new way to enable efficient hydrolysis and greatly enhances the hydrolysis activity of CaH_(2)/(Al/Si)composites.The novel fuel composites(NaH-CaH_(2)/Al)have extraordinary FC performance and a 0.42 W/cm2 peak power density greater than commercial hydrogen generators.It provides high H_(2)yield 84.4%for NaH-CaH_(2)/Al and 82%for NaH-CaH_(2)/Si compared to NaOH-CaH_(2)(Al/Si),NaCl-CaH_(2)(Al/Si),and KCl-CaH_(2)(Al/Si)composites.The NaH bridge effect hinders the direct water contact and stops the formation of Ca(OH)2 around Al/Si,which provides adequate pathways for the CaH_(2)(Al/Si)hydrolysis.The impressive capabilities of novel fuel composites are anticipated to offer practical uses in fuel cells,automobile applications,and portable/on-board H_(2)generation.展开更多
In-situ TiB2 particles reinforced 2014 aluminum alloy composite was prepared using an exothermic reaction process with K2TiF6 and KBF4 salts. The effects of CeO2 additive on the microstructure and properties of in-sit...In-situ TiB2 particles reinforced 2014 aluminum alloy composite was prepared using an exothermic reaction process with K2TiF6 and KBF4 salts. The effects of CeO2 additive on the microstructure and properties of in-situ TiB2/2014 composite were investigated. The results showed that CeO2 at high temperature exhibits the same function as Ce. When 0.5% （mass fraction） CeO2 additive was added, the dispersion of TiB2 particles in the matrix is improved significantly, and particles have no obvious settlement. The dispersing mechanism of TiB2 particles in 2014 Al alloy matrix was explained. Compared with the composite without CeO2, the hardness, tensile strength, yield strength and elongation of the composite with CeO2 addition are greatly increased in as-cast condition.展开更多
Zn-Al-Cu-TiB2（ZA27-TiB2） in situ composites were fabricated via reactions between molten aluminum and mixed halide salts（K2TiF6 and KBF4） at temperature of 875 °C. The microstructure, mechanical properties an...Zn-Al-Cu-TiB2（ZA27-TiB2） in situ composites were fabricated via reactions between molten aluminum and mixed halide salts（K2TiF6 and KBF4） at temperature of 875 °C. The microstructure, mechanical properties and wear behavior of the composites were investigated. Microstructure analysis shows that fine and clean TiB2 particles distribute uniformly through the matrix. The mechanical properties of the composites increase with the increase in TiB2 content. As TiB2 content increases to 5%（mass fraction）, an improvement of HB 18 in hardness and 49 MPa in ultimate tensile strength（UTS） is achieved. The overall results reveal that the composites possess low friction coefficients and the wear rate is reduced from 5.9×10-3 to 1.3×10-3 mm3/m after incorporating 5% TiB2. Friction coefficient and worn surface analysis indicate that there is a change in the wear mechanism in the initial stage of wear test after introducing in situ TiB2 particles into the matrix.展开更多
In electrolyte melts containing K at low temperature, the penetrative and migratory path of alkali metals （K and Na） in pitch, furan, phenolic aldehyde and epoxy based TiB2-C composite cathodes during the electrolys...In electrolyte melts containing K at low temperature, the penetrative and migratory path of alkali metals （K and Na） in pitch, furan, phenolic aldehyde and epoxy based TiB2-C composite cathodes during the electrolysis process were studied by EDS and self-made modified Rapoport apparatus. The electrolysis expansion rates, the diffusion coefficients of the alkali metals and the corrosion rates of the composite cathode were also calculated and discussed. The results show that no matter what kind of binder is used, alkali metals have the same penetrative path in composite cathodes：firstly in pore, then in binder and finally in carbonaceous aggregates. K and Na penetrate into both binder and carbonaceous aggregates, which leads to the expansion of composite cathodes, and K has stronger penetration ability than Na. Electrolysis expansion rate of resin based composite cathode is smaller than that of pitch based composite cathodes, and so do the diffusion coefficient and corrosion rate. Resin based composite cathode has better resistance ability to the penetration of alkali metals than pith based composite cathode, and phenolic aldehyde based composite cathode exhibits the strongest resistance ability. The penetration rate, the diffusion coefficient of alkali metals in phenolic aldehyde based TiB2-C composite cathode and the corresponding corrosion rate are 4.72 mm/h, 2.24×10^-5 cm^2/s and 2.31 mm/a, respectively.展开更多
TiB2/Al-30Si composites were fabricated via in-situ melt reaction under high-energy ultrasonic field. The microstructure and wear properties of the composite were investigated by XRD, SEM and dry sliding testing. The ...TiB2/Al-30Si composites were fabricated via in-situ melt reaction under high-energy ultrasonic field. The microstructure and wear properties of the composite were investigated by XRD, SEM and dry sliding testing. The results indicate that TiB2 reinforcement particles are uniformly distributed in the aluminum matrix under high-energy ultrasonic field. The morphology of the TiB2 particles is in circle-shape or quadrangle-shape, and the size of the particles is 0.1-1.5μm. The primary silicon particles are in quadrangle-shape and the average size of them is about 10μm. Hardness values of the Al-30Si matrix alloy and the TiB2/Al-30Si composites considerably increase as the high energy ultrasonic power increases. In particular, the maximum hardness value of the in-situ composites is about 1.3 times as high as that of the matrix alloy when the ultrasonic power is 1.2 kW, reaching 412 MPa. Meanwhile, the wear resistance of the in-situ TiB2/Al-30Si composites prepared under high-energy ultrasonic field is obviously improved and is insensitive to the applied loads of the dry sliding testing.展开更多
（TiB2＋Al2O3）/NiAl composites were synthesized by self-propagation high-temperature synthesis, and their phase compositions, microstructures and evolution modes were studied. The microstructures and shapes vary with...（TiB2＋Al2O3）/NiAl composites were synthesized by self-propagation high-temperature synthesis, and their phase compositions, microstructures and evolution modes were studied. The microstructures and shapes vary with the TiB2＋Al2O3 content in the NiAl matrix. TiB2 particles take a great variety of elementary shapes such as white bars, plates, herringbones, regular cubes and cuboids. These results outline a strategy of self-assembly processes in real time to build diversified microstructures. Some TiB2 grains in sizes of 2-5μm are embeded in Al2O3 clusters, while a small number of TiB2 particles disperse in the NiAl matrix. It is believed that the higher the TiB2＋Al2O3 content is, the more the regular shapes and homogeneous distributions of TiB2 and Al2O3 will be present in the NiAl matrix.展开更多
An Al_(2)O_(3)/Al-Cu-Mn composite was fabricated using a combination of ball milling and liquid-solid reaction,with a nominal composition of Al-4Cu-0.5Mn-2.8γ-Al_(2)O_(3).The composite contains reinforcement particle...An Al_(2)O_(3)/Al-Cu-Mn composite was fabricated using a combination of ball milling and liquid-solid reaction,with a nominal composition of Al-4Cu-0.5Mn-2.8γ-Al_(2)O_(3).The composite contains reinforcement particles,including nano-sizedθ’and T(Al_(20)Cu_(2)Mn_(3))particles after T6 heat treatment,as well as in-situ synthesized nano-sizedγ-Al_(2)O_(3)particles.Tensile tests of the Al-4Cu-0.5Mn-2.8γ-Al_(2)O_(3)composite and the Al-4Cu-0.5Mn base alloy after T6 treatment were carried out at room temperature and elevated temperatures(200°C,300°C,and 400°C).Compared with the base alloy,the yield strength of the Al-4Cu-0.5Mn-2.8γ-Al_(2)O_(3)composite after T6 treatment increases significantly from 187 MPa to 263 MPa at room temperature.Simultaneously,at elevated temperatures,the yield strength is also enhanced,with a yield strength of 52 MPa at 400°C for this composite.The in-situ fabricatedγ-Al_(2)O_(3)particles,mainly distributed along the grain boundaries,are supposed to play the main strengthening role,especially at high temperatures.This work acts as a reference for designing composites for high-temperature applications.展开更多
The hot forming behavior,failure mechanism,and microstructure evolution of in-situ TiB_(2)particle-reinforced 7075 aluminum matrix composite were investigated by isothermal compression test under different deformation...The hot forming behavior,failure mechanism,and microstructure evolution of in-situ TiB_(2)particle-reinforced 7075 aluminum matrix composite were investigated by isothermal compression test under different deformation conditions of deformation temperatures of 300−450℃ and strain rates of 0.001^(−1)s^(−1).The results demonstrate that the failure behavior of the composite exhibits both particle fracture and interface debonding at low temperature and high strain rate,and dimple rupture of the matrix at high temperature and low strain rate.Full dynamic recrystallization,which improves the composite formability,occurs under conditions of high temperature(450℃)and low strain rate(0.001 s^(−1));the grain size of the matrix after hot compression was significantly smaller than that of traditional 7075Al and ex-situ particle reinforced 7075Al matrix composite.Based on the flow stress curves,a constitutive model describing the relationship of the flow stress,true strain,strain rate and temperature was proposed.Furthermore,the processing maps based on both the dynamic material modeling(DMM)and modified DMM(MDMM)were established to analyze flow instability domain of the composite and optimize hot forming processing parameters.The optimum processing domain was determined at temperatures of 425−450℃ and strain rates of 0.001−0.01 s^(−1),in which the fine grain microstructure can be gained and particle crack and interface debonding can be avoided.展开更多
The mathematical models were developed to predict the ultimate tensile strength （UTS） and hardness of Al/TiB2 MMCs fabricated by in situ reaction process. The process parameters include temperature, reaction time an...The mathematical models were developed to predict the ultimate tensile strength （UTS） and hardness of Al/TiB2 MMCs fabricated by in situ reaction process. The process parameters include temperature, reaction time and mass fraction of TiB2. The in-situ casting was carried out based on three-factor five-level central composite rotatable design using response surface methodology （RSM）. The validation of the model was carried out using ANOVA. The mathematical models developed for the mechanical properties were predicted at 95% confidence limit.展开更多
TiC-TiB2-Cu composites were produced by self-propagating high-temperature synthesis combined with pseudo hot isostatic pressing using Ti, B4C and Cu powders. The microstructure and mechanical properties of the composi...TiC-TiB2-Cu composites were produced by self-propagating high-temperature synthesis combined with pseudo hot isostatic pressing using Ti, B4C and Cu powders. The microstructure and mechanical properties of the composites were investigated. The X-ray diffraction （XRD） and scanning electron microscopy （SEM） results showed that the final products were only TiC, TiB2 and Cu phases. The clubbed TiB2 grains and spheroidal or irregular TiC grains were found in the microstructure of synthesized products. The reaction temperature and grain size of TiB2 and TiC particles decreased with increasing Cu content. The introduction of Cu into the composites resulted in a drastic increase in the relative density and flexual strength, and the maximum values were obtained with the addition of 20 wt pct, while the fracture toughness was the best when Cu content was 40 wt pct.展开更多
The electrical resistivity of TiB2/C cathode composite coating at different temperatures was measured with the electrical conductivity test device; the effects of TiB2 content and kinds of carbonaceous fillers as well...The electrical resistivity of TiB2/C cathode composite coating at different temperatures was measured with the electrical conductivity test device; the effects of TiB2 content and kinds of carbonaceous fillers as well as their mean particle size on their electrical resistivities were investigated. The results show that electrical resistivity of the coating decreases with the increase of TiB2 content and the decrease of its mean particle size. When the mass fraction of TiB2 increases from 30% to 60%, the electrical resistivity of the coating at room temperature decreases from 31.2μΩ·m to 23.8μΩ·m. The electrical resistivity of the coating at 960℃ lowers from 76.1μΩ· m to 38.4μΩ·m with the decrease of TiB2 mean particle size from 12μm to 1μm. The kinds of carbonaceous fillers have great influence on the electrical resistivity of TiB2/C composite coating at 960℃, when the graphite, petroleum coke and anthracite are used as fillers, the electrical resistivities of the coating are 20.3μΩ·m, 53.7μΩ·m and 87.2μΩ·m, respectively. For the coating with petroleum coke filler, its electrical resistivity decreases with the increase of the mean particle size of petroleum coke filler. The electrical resistivity at 960℃ decreases from 56.2μΩ·m to 48.2μΩ·m with the mean particle size of petroleum coke increasing from 44μm to 1200μm. However, too big carbonaceous particle size has adverse influence on the abrasion resistance of coating. Its proper mean particle size is 420μm.展开更多
Titanium matrix （Ti6Al4V） composites rein- forced with TiB2 and TiC were produced through powder metallurgy method. The effect of addition of both TiB2 and TiC with different contents （2.5 wt%, 5.0 wt% and 7.5 wt%...Titanium matrix （Ti6Al4V） composites rein- forced with TiB2 and TiC were produced through powder metallurgy method. The effect of addition of both TiB2 and TiC with different contents （2.5 wt%, 5.0 wt% and 7.5 wt%） on the density, microstructure and hardness properties of titanium matrix was investigated. The size distributions of the matrix alloy and reinforcement particles were measured by particle size analyzer. Microhardness of the sintered composites was evaluated using Vickers＇s hardness tester with a normal load of 3 N and a dwell time of 10 s. Ti6Al4V alloy and Ti6Al4V/TiB2-TiC composites were characterized through X-ray diffraction （XRD） and field emission scanning electron microscope （FESEM） equipped with energy-dispersive spectrometer （EDS）. The addition of TiB2 and TiC particles enriches the properties of Ti6Al4V alloy. The sintered Ti6Al4V/TiB2-TiC composite features a dense and pore-free microstructure with varying TiB2 and TiC particle distribution in the metal matrix. The results of this study show that the development of new phases plays a significant role in the properties of these composite materials.展开更多
A novel technique for fabricating TiB_2/Al composites in molten aluminum was introduced. The formation mechanism of brittleAl,Ti particulates up to 30 m in size produced in the composites was studied and a method of e...A novel technique for fabricating TiB_2/Al composites in molten aluminum was introduced. The formation mechanism of brittleAl,Ti particulates up to 30 m in size produced in the composites was studied and a method of eliminating them was proposed. The resultsshow that (l) the brittle Al,Ti particulates are always present in the composites when the molar ratio of Ti to B 'T,:nB is l:2; and (2) theformation of the brittle Al,Ti phase can be avoided entirely from the final product by using a proper 'T,:nB of l:4 in the Ti-B-Al preforms.In the former case, the tensile elongation of the composite is only 4%, much lower than the value of pure aluminum (20%). In the latercase, the tensile elongation of this composite is 10%, higher than the value of the composite with a lot ofAl,Ti (4%), whereas the ultimatetensile stfength of the former is nearly that of the later.展开更多
TiB2 and Dy2O3 were used as codeposited particles in the preparation of Ni-TiB2-Dy2O3 composite coatings to improve its performance. Ni-TiB2-Dy2O3 composite coatings were prepared by electrodeposition method with a ni...TiB2 and Dy2O3 were used as codeposited particles in the preparation of Ni-TiB2-Dy2O3 composite coatings to improve its performance. Ni-TiB2-Dy2O3 composite coatings were prepared by electrodeposition method with a nickel cetyltrimethylammonium bromide and hexadecylpyridinium bromide solution containing TiB2 and Dy2O3 particles. The content of codeposited TiB2 and Dy2O3 in the composite coatings was controlled by adding TiB2 and Dy2O3 particles of different concentrations into the solution, respectively. The effects of TiB2 and Dy2O3 content on microhardness, wear mass loss and friction coefficients of composite coatings were investigated. The composite coatings were characterized by X-ray diffraction （XRD）, inductively coupled plasma-atomic emission spectrometer （ICP-AES） and scanning electron microscopy （SEM） techniques. Ni-TiBE-Dy2O3 composite coatings showed higher microhardness, lower wear mass loss and friction coefficient compared with those of the pure Ni coating and Ni-TiB2 composite coatings. The wear mass loss of Ni-TiB2-Dy2O3 composite coatings was 9 and 1.57 times lower than that of the pure Ni coating and Ni-TiB2 composite coatings, respectively. The friction coefficient of pure Ni coating, Ni-TiB2 and Ni-TiB2-Dy2O3 composite coatings were 0.723, 0.815 and 0.619, respectively. Ni-TiBE-Dy2O3 composite coatings displayed the least friction coefficient among the three coatings. Dy2O3 particles in composite coatings might serve as a solid lubricant between contact surfaces to decrease the friction coefficient and abate the wear of the composite coatings. The loading-bearing capacity and the wear-reducing effect of the Dy2O3 particles were closely related to the content of Dy2O3 particles in the composite coatings.展开更多
A kind of Al-TiB2/TiC in situ composite with a homogenous microstructure was successfully prepared through in situ reaction of pure Ti and Al-B-C alloy with molten aluminum.In order to improve the distribution of the ...A kind of Al-TiB2/TiC in situ composite with a homogenous microstructure was successfully prepared through in situ reaction of pure Ti and Al-B-C alloy with molten aluminum.In order to improve the distribution of the particles and mechanical properties of the composites,subsequent hot rolling with increasing reduction was carried out.The microstructure evolution of the composites was characterized using field emission scanning electron microscopy(FESEM)and the mechanical properties were studied through tensile tests and microhardness measurement.It is found that both the microstructure uniformity and mechanical properties of the composites are significantly improved with increasing rolling reduction.The ultimate tensile strength and microhardness of the composites with90%rolling reduction reach185.9MPa and HV59.8,respectively,140%and35%higher than those of as-cast ones.Furthermore,the strengthening mechanism of the composite was analyzed based on the fracture morphologies.展开更多
TiB2-Ni composite powders were prepared by pressurized hydrogen reduction cladding with different proportion of TiB2.The coatings were then prepared by APS.The microstructures and the phase composition of the powders ...TiB2-Ni composite powders were prepared by pressurized hydrogen reduction cladding with different proportion of TiB2.The coatings were then prepared by APS.The microstructures and the phase composition of the powders as well as the deposited coatings were analyzed by scanning electron microscopy(SEM)and X-ray diffraction(XRD).The coatings were tested using a ring-on-disc tribometer from ambient temperature to 300°C.A sprayed Cr3C2-NiCr coating was tested as a reference.The morphologies of the worn surface of the coatings were observed and analyzed.It is found that the TiB2-Ni composite coatings present higher friction coefficient than that of the Cr3C2-NiCr coating at room temperature due to the adhesive wear mechanism,whereas the main wear mechanism of Cr3C2-NiCr coating is rupture and exfoliation.However,at high temperature,the friction coefficient of the TiB2-Ni composite coating decreases as a result of B2O3 solid lubricant,which alleviates the adhesive wear on coatings.Furthermore,the TiB2-Ni composite coating greatly reduces the mass loss of the boron cast iron.展开更多
TiB2/TiB/TiNx(x=1,0.3)/Ti composite coating was prepared on pure Ti by laser surface alloying by using powders of boron as starting materials.The composite coating was examined by X-ray diffraction(XRD),high-resolutio...TiB2/TiB/TiNx(x=1,0.3)/Ti composite coating was prepared on pure Ti by laser surface alloying by using powders of boron as starting materials.The composite coating was examined by X-ray diffraction(XRD),high-resolution transmission electron microscopy(HRTEM)and scanning electron microscopy(SEM).The friction and wear properties of the composite coating were examined using a pin-on-disk tester under dry sliding wear condition.The results showed that the top surface of the composite coating was mainly composed of TiB2,TiB,TiN0.3,TiN and Ti phases,while the interface of the composite coating was composed of TiB and Ti phases.The composite coating showed sticklike structure near the top surface,and dendrites structure near the interface.The friction and wear test showed that the composite coating had better wear resistance than pure Ti due to their higher microhardness than that of pure Ti substrate.展开更多
Lightweight hybrid structures of Al MMCs and titanium alloy dissimilar materials have great prospect in the defence industry application. So, it is necessary to join Al MMCs with Ti metal to achieve this structural de...Lightweight hybrid structures of Al MMCs and titanium alloy dissimilar materials have great prospect in the defence industry application. So, it is necessary to join Al MMCs with Ti metal to achieve this structural design. In this work, in-situ Ti B_(2)/7050 composite and TA2 were firstly attempted to join by TIG welding-brazing technique. The result was that the intact welding-brazing butt joint was successfully fabricated. The joint presents dual characteristics, being a brazing on TA2 side and a welding on Ti B_(2)/7050 side. At brazing joint side, ER4043 filler metal effectively wets on TA2 under TIG heating condition,and a continuous interfacial reaction layer with 1 e3 mm is formed at welded metal/TA2 interface. The whole interfacial reaction layers are composed of Ti(Al Si)3 intermetallic compounds(IMCs), but their morphologies at the different regions present obvious distinguishes. The microhardness of the reaction layers is as much as 141 e190 HV. At welding joints side, the fusion zone appears the equixaed crystal structure, and the grain sizes are much smaller than those of welded metal, which is attributed to the effect of Ti B2 particulates from the melted Ti B_(2)/7050 on acceleration formation and inhibiting growth for the new crystal nucleus. The tensile test results show that average tensile strength of the optimal welding-brazing joint is able to achieve 138 MPa. The failure of the tensile joint occurs by quasi-cleavage pattern, and the cracks initiate from the IMCs layer at the groove surface of TA2 and propagate into the welded metal.展开更多
The NiAl–TiC–TiB2 composites were processed by self-propagating high-temperature synthesis（SHS） method using raw powders of Ni, Al, Ti, B4 C, TiC, and TiB2, and their microstructure and micro-hardness were investi...The NiAl–TiC–TiB2 composites were processed by self-propagating high-temperature synthesis（SHS） method using raw powders of Ni, Al, Ti, B4 C, TiC, and TiB2, and their microstructure and micro-hardness were investigated. The TiC–TiB2 in NiAl matrix, with contents from 10 to 30 wt%, emerged with the use of two methods： in situ formed and externally added. The results show that all final products are composed of three phases of NiAl, TiC, and TiB2. The microstructures of NiAl–TiC–TiB2 composites with in situ-formed TiC and TiB2 are fine, and all the three phases are distributed uniformly. The grains of NiAl matrix in the composites have been greatly refined, and the micro-hardness of NiAl increases from 381 HV100 to 779 HV100. However, the microstructures of NiAl–TiC–TiB2 composites with externally added TiC and TiB2 are coarse and inhomogeneous, with severe agglomeration of TiC and TiB2 particles. The samples containing externally added 30 wt% TiC–TiB2attain the micro-hardness of 485 HV100. The microstructure evolution and fracture mode of the two kinds of NiAl–TiC–TiB2 composites are different.展开更多
Pitch and TiB2/C green composite cathode material were respectively analyzed with simultaneous DSC-TGA, and effects of three baking processes of TiB2/C composite cathode material, i.e. K25, K5 and M5, on properties of...Pitch and TiB2/C green composite cathode material were respectively analyzed with simultaneous DSC-TGA, and effects of three baking processes of TiB2/C composite cathode material, i.e. K25, K5 and M5, on properties of TiB2/C composite cathode material were investigated. The results show that thermogravimetrie behavior of pitch and TiB2/C green composite cathode is similar, and appears the largest mass loss rate in the temperature range from 200 to 600 ℃. The bulk density variation of sample K5 before and after baking is the largest （11.9%）, that of sample K25 is the second, and that of sample M5 is the smallest （6.7%）. The crushing strength of sample M5 is the biggest （51.2 MPa）, that of sample K2.5 is the next, and that of sample K5 is the smallest （32.8 MPa）. But, the orders of the electrical resistivity and electrolysis expansion of samples are just opposite with the order of crushing strength. The heating rate has a great impact on the microstructure of sample. The faster the heating rate is, the bigger the pore size and porosity of sample are. Compared with the heating rate between 200 and 600℃ of samples K25 and K5, that of sample M5 is slower and suitable for baking process of TiB2/C composite cathode material.展开更多
基金financial support granted by the National Natural Science Foundation of China (No. 22402225)the Gusu Innovation and Entrepreneurship Leading Talent Plan(No. ZXL2023193)+2 种基金the Sinano Talents Plan (No. 2022000175)the Guangdong Basic and Applied Basic Research Foundation (No.2023A1515111133)the ANSO Scholarship for Young Talents
文摘Inorganic materials can solve transportable and on-site hydrolytic hydrogen generation issues.CaH_(2)/(Al/Si)composites are preferable due to their notable chemical properties.However,these composites require pretreatments,an inert environment,and long hours of physical ball milling for high homogeneity and synergistic effects.CaH_(2)also inhibits the hydrolysis reaction by forming its products on the Al/Si surface,which hinders the direct utilization of composites.This work represents the first investigation of NaH-CaH_(2)(Al/Si)fuel composites,which greatly overcome these limitations and can be directly used for on-site hydrogen generation and proton exchange membrane(PEM)fuel cells.The NaH-CaH_(2)(Al/Si)fuel composites were prepared by using a straightforward mixing method with variable composition ratios,showing high H_(2)yield and fuel cell(FC)performance.NaH addition provides the bridge effect,which opens up a new way to enable efficient hydrolysis and greatly enhances the hydrolysis activity of CaH_(2)/(Al/Si)composites.The novel fuel composites(NaH-CaH_(2)/Al)have extraordinary FC performance and a 0.42 W/cm2 peak power density greater than commercial hydrogen generators.It provides high H_(2)yield 84.4%for NaH-CaH_(2)/Al and 82%for NaH-CaH_(2)/Si compared to NaOH-CaH_(2)(Al/Si),NaCl-CaH_(2)(Al/Si),and KCl-CaH_(2)(Al/Si)composites.The NaH bridge effect hinders the direct water contact and stops the formation of Ca(OH)2 around Al/Si,which provides adequate pathways for the CaH_(2)(Al/Si)hydrolysis.The impressive capabilities of novel fuel composites are anticipated to offer practical uses in fuel cells,automobile applications,and portable/on-board H_(2)generation.
基金Project (2008AA03A239) supported by the High-tech Research and Development Program of China
文摘In-situ TiB2 particles reinforced 2014 aluminum alloy composite was prepared using an exothermic reaction process with K2TiF6 and KBF4 salts. The effects of CeO2 additive on the microstructure and properties of in-situ TiB2/2014 composite were investigated. The results showed that CeO2 at high temperature exhibits the same function as Ce. When 0.5% （mass fraction） CeO2 additive was added, the dispersion of TiB2 particles in the matrix is improved significantly, and particles have no obvious settlement. The dispersing mechanism of TiB2 particles in 2014 Al alloy matrix was explained. Compared with the composite without CeO2, the hardness, tensile strength, yield strength and elongation of the composite with CeO2 addition are greatly increased in as-cast condition.
基金Projects(51071035,51274054,51375070)supported by the National Natural Science Foundation of ChinaProject(313011)supported by the Key Project of Ministry of Education of China
文摘Zn-Al-Cu-TiB2（ZA27-TiB2） in situ composites were fabricated via reactions between molten aluminum and mixed halide salts（K2TiF6 and KBF4） at temperature of 875 °C. The microstructure, mechanical properties and wear behavior of the composites were investigated. Microstructure analysis shows that fine and clean TiB2 particles distribute uniformly through the matrix. The mechanical properties of the composites increase with the increase in TiB2 content. As TiB2 content increases to 5%（mass fraction）, an improvement of HB 18 in hardness and 49 MPa in ultimate tensile strength（UTS） is achieved. The overall results reveal that the composites possess low friction coefficients and the wear rate is reduced from 5.9×10-3 to 1.3×10-3 mm3/m after incorporating 5% TiB2. Friction coefficient and worn surface analysis indicate that there is a change in the wear mechanism in the initial stage of wear test after introducing in situ TiB2 particles into the matrix.
基金Project (51304152) supported by the National Natural Science Foundation of ChinaProject (2013JQ7016) supported by the Natural Science Foundation of Shanxi Province,ChinaProject (2013JK0904) supported by Shanxi Provincial Education Department,China
文摘In electrolyte melts containing K at low temperature, the penetrative and migratory path of alkali metals （K and Na） in pitch, furan, phenolic aldehyde and epoxy based TiB2-C composite cathodes during the electrolysis process were studied by EDS and self-made modified Rapoport apparatus. The electrolysis expansion rates, the diffusion coefficients of the alkali metals and the corrosion rates of the composite cathode were also calculated and discussed. The results show that no matter what kind of binder is used, alkali metals have the same penetrative path in composite cathodes：firstly in pore, then in binder and finally in carbonaceous aggregates. K and Na penetrate into both binder and carbonaceous aggregates, which leads to the expansion of composite cathodes, and K has stronger penetration ability than Na. Electrolysis expansion rate of resin based composite cathode is smaller than that of pitch based composite cathodes, and so do the diffusion coefficient and corrosion rate. Resin based composite cathode has better resistance ability to the penetration of alkali metals than pith based composite cathode, and phenolic aldehyde based composite cathode exhibits the strongest resistance ability. The penetration rate, the diffusion coefficient of alkali metals in phenolic aldehyde based TiB2-C composite cathode and the corresponding corrosion rate are 4.72 mm/h, 2.24×10^-5 cm^2/s and 2.31 mm/a, respectively.
基金Project(51174098)supported by the National Natural Science Foundation of ChinaProject(kjsmcx0903)supported by the Foundation of the Jiangsu Province Key Laboratory of Materials Tribology,China+2 种基金Project(1202015B)supported by the Postdoctoral Science Foundation of Jiangsu Province,ChinaProject(03)supported by the Undergraduate Practice-Innovation Training Foundation of Jiangsu University,ChinaProjects(GY2012020,GY2013032)supported by the Science and Technology Support Plan Project Foundation of Zhenjiang City,China
文摘TiB2/Al-30Si composites were fabricated via in-situ melt reaction under high-energy ultrasonic field. The microstructure and wear properties of the composite were investigated by XRD, SEM and dry sliding testing. The results indicate that TiB2 reinforcement particles are uniformly distributed in the aluminum matrix under high-energy ultrasonic field. The morphology of the TiB2 particles is in circle-shape or quadrangle-shape, and the size of the particles is 0.1-1.5μm. The primary silicon particles are in quadrangle-shape and the average size of them is about 10μm. Hardness values of the Al-30Si matrix alloy and the TiB2/Al-30Si composites considerably increase as the high energy ultrasonic power increases. In particular, the maximum hardness value of the in-situ composites is about 1.3 times as high as that of the matrix alloy when the ultrasonic power is 1.2 kW, reaching 412 MPa. Meanwhile, the wear resistance of the in-situ TiB2/Al-30Si composites prepared under high-energy ultrasonic field is obviously improved and is insensitive to the applied loads of the dry sliding testing.
基金Project(51272141)supported by the National Natural Science Foundation of ChinaProject(ts20110828)supported by the Taishan Scholars Project of Shandong Province,ChinaProject(2015AA034404)supported by the Ministry of Science and Technology of China
文摘（TiB2＋Al2O3）/NiAl composites were synthesized by self-propagation high-temperature synthesis, and their phase compositions, microstructures and evolution modes were studied. The microstructures and shapes vary with the TiB2＋Al2O3 content in the NiAl matrix. TiB2 particles take a great variety of elementary shapes such as white bars, plates, herringbones, regular cubes and cuboids. These results outline a strategy of self-assembly processes in real time to build diversified microstructures. Some TiB2 grains in sizes of 2-5μm are embeded in Al2O3 clusters, while a small number of TiB2 particles disperse in the NiAl matrix. It is believed that the higher the TiB2＋Al2O3 content is, the more the regular shapes and homogeneous distributions of TiB2 and Al2O3 will be present in the NiAl matrix.
基金supported by the National Natural Science Foundation of China(No.52471040)the Natural Science Foundation of Shandong Province(No.ZR2022ME005).
文摘An Al_(2)O_(3)/Al-Cu-Mn composite was fabricated using a combination of ball milling and liquid-solid reaction,with a nominal composition of Al-4Cu-0.5Mn-2.8γ-Al_(2)O_(3).The composite contains reinforcement particles,including nano-sizedθ’and T(Al_(20)Cu_(2)Mn_(3))particles after T6 heat treatment,as well as in-situ synthesized nano-sizedγ-Al_(2)O_(3)particles.Tensile tests of the Al-4Cu-0.5Mn-2.8γ-Al_(2)O_(3)composite and the Al-4Cu-0.5Mn base alloy after T6 treatment were carried out at room temperature and elevated temperatures(200°C,300°C,and 400°C).Compared with the base alloy,the yield strength of the Al-4Cu-0.5Mn-2.8γ-Al_(2)O_(3)composite after T6 treatment increases significantly from 187 MPa to 263 MPa at room temperature.Simultaneously,at elevated temperatures,the yield strength is also enhanced,with a yield strength of 52 MPa at 400°C for this composite.The in-situ fabricatedγ-Al_(2)O_(3)particles,mainly distributed along the grain boundaries,are supposed to play the main strengthening role,especially at high temperatures.This work acts as a reference for designing composites for high-temperature applications.
基金the National Science and Technology Major Project of the Ministry of Science and Technology of China(No.2018-ZX04044001-008)the National Natural Science Foundation of China(No.52075328).
文摘The hot forming behavior,failure mechanism,and microstructure evolution of in-situ TiB_(2)particle-reinforced 7075 aluminum matrix composite were investigated by isothermal compression test under different deformation conditions of deformation temperatures of 300−450℃ and strain rates of 0.001^(−1)s^(−1).The results demonstrate that the failure behavior of the composite exhibits both particle fracture and interface debonding at low temperature and high strain rate,and dimple rupture of the matrix at high temperature and low strain rate.Full dynamic recrystallization,which improves the composite formability,occurs under conditions of high temperature(450℃)and low strain rate(0.001 s^(−1));the grain size of the matrix after hot compression was significantly smaller than that of traditional 7075Al and ex-situ particle reinforced 7075Al matrix composite.Based on the flow stress curves,a constitutive model describing the relationship of the flow stress,true strain,strain rate and temperature was proposed.Furthermore,the processing maps based on both the dynamic material modeling(DMM)and modified DMM(MDMM)were established to analyze flow instability domain of the composite and optimize hot forming processing parameters.The optimum processing domain was determined at temperatures of 425−450℃ and strain rates of 0.001−0.01 s^(−1),in which the fine grain microstructure can be gained and particle crack and interface debonding can be avoided.
文摘The mathematical models were developed to predict the ultimate tensile strength （UTS） and hardness of Al/TiB2 MMCs fabricated by in situ reaction process. The process parameters include temperature, reaction time and mass fraction of TiB2. The in-situ casting was carried out based on three-factor five-level central composite rotatable design using response surface methodology （RSM）. The validation of the model was carried out using ANOVA. The mathematical models developed for the mechanical properties were predicted at 95% confidence limit.
基金The work was supported by the Foundation of Aerospace Innovation Fund and the National Natural Science Foundation of China(No.90505015)the Foundation of National Key Laboratory for Remanufacturing.
文摘TiC-TiB2-Cu composites were produced by self-propagating high-temperature synthesis combined with pseudo hot isostatic pressing using Ti, B4C and Cu powders. The microstructure and mechanical properties of the composites were investigated. The X-ray diffraction （XRD） and scanning electron microscopy （SEM） results showed that the final products were only TiC, TiB2 and Cu phases. The clubbed TiB2 grains and spheroidal or irregular TiC grains were found in the microstructure of synthesized products. The reaction temperature and grain size of TiB2 and TiC particles decreased with increasing Cu content. The introduction of Cu into the composites resulted in a drastic increase in the relative density and flexual strength, and the maximum values were obtained with the addition of 20 wt pct, while the fracture toughness was the best when Cu content was 40 wt pct.
基金Project(2005CB623703) supported by the State Key Fundamental Research and Development Programof China project(5JJ30103) supported by the Natural Science Foundation of Hunan Province
文摘The electrical resistivity of TiB2/C cathode composite coating at different temperatures was measured with the electrical conductivity test device; the effects of TiB2 content and kinds of carbonaceous fillers as well as their mean particle size on their electrical resistivities were investigated. The results show that electrical resistivity of the coating decreases with the increase of TiB2 content and the decrease of its mean particle size. When the mass fraction of TiB2 increases from 30% to 60%, the electrical resistivity of the coating at room temperature decreases from 31.2μΩ·m to 23.8μΩ·m. The electrical resistivity of the coating at 960℃ lowers from 76.1μΩ· m to 38.4μΩ·m with the decrease of TiB2 mean particle size from 12μm to 1μm. The kinds of carbonaceous fillers have great influence on the electrical resistivity of TiB2/C composite coating at 960℃, when the graphite, petroleum coke and anthracite are used as fillers, the electrical resistivities of the coating are 20.3μΩ·m, 53.7μΩ·m and 87.2μΩ·m, respectively. For the coating with petroleum coke filler, its electrical resistivity decreases with the increase of the mean particle size of petroleum coke filler. The electrical resistivity at 960℃ decreases from 56.2μΩ·m to 48.2μΩ·m with the mean particle size of petroleum coke increasing from 44μm to 1200μm. However, too big carbonaceous particle size has adverse influence on the abrasion resistance of coating. Its proper mean particle size is 420μm.
文摘Titanium matrix （Ti6Al4V） composites rein- forced with TiB2 and TiC were produced through powder metallurgy method. The effect of addition of both TiB2 and TiC with different contents （2.5 wt%, 5.0 wt% and 7.5 wt%） on the density, microstructure and hardness properties of titanium matrix was investigated. The size distributions of the matrix alloy and reinforcement particles were measured by particle size analyzer. Microhardness of the sintered composites was evaluated using Vickers＇s hardness tester with a normal load of 3 N and a dwell time of 10 s. Ti6Al4V alloy and Ti6Al4V/TiB2-TiC composites were characterized through X-ray diffraction （XRD） and field emission scanning electron microscope （FESEM） equipped with energy-dispersive spectrometer （EDS）. The addition of TiB2 and TiC particles enriches the properties of Ti6Al4V alloy. The sintered Ti6Al4V/TiB2-TiC composite features a dense and pore-free microstructure with varying TiB2 and TiC particle distribution in the metal matrix. The results of this study show that the development of new phases plays a significant role in the properties of these composite materials.
文摘A novel technique for fabricating TiB_2/Al composites in molten aluminum was introduced. The formation mechanism of brittleAl,Ti particulates up to 30 m in size produced in the composites was studied and a method of eliminating them was proposed. The resultsshow that (l) the brittle Al,Ti particulates are always present in the composites when the molar ratio of Ti to B 'T,:nB is l:2; and (2) theformation of the brittle Al,Ti phase can be avoided entirely from the final product by using a proper 'T,:nB of l:4 in the Ti-B-Al preforms.In the former case, the tensile elongation of the composite is only 4%, much lower than the value of pure aluminum (20%). In the latercase, the tensile elongation of this composite is 10%, higher than the value of the composite with a lot ofAl,Ti (4%), whereas the ultimatetensile stfength of the former is nearly that of the later.
基金supported by the Science Technology Foundation of Shanghai (072305113)the Program for Professor of Special Appointment (Eastern Scholar) at Shanghai Institutions of Higher Learning and Science Technology Foundation of Shanghai Institute of Technology (KJ2008-07)
文摘TiB2 and Dy2O3 were used as codeposited particles in the preparation of Ni-TiB2-Dy2O3 composite coatings to improve its performance. Ni-TiB2-Dy2O3 composite coatings were prepared by electrodeposition method with a nickel cetyltrimethylammonium bromide and hexadecylpyridinium bromide solution containing TiB2 and Dy2O3 particles. The content of codeposited TiB2 and Dy2O3 in the composite coatings was controlled by adding TiB2 and Dy2O3 particles of different concentrations into the solution, respectively. The effects of TiB2 and Dy2O3 content on microhardness, wear mass loss and friction coefficients of composite coatings were investigated. The composite coatings were characterized by X-ray diffraction （XRD）, inductively coupled plasma-atomic emission spectrometer （ICP-AES） and scanning electron microscopy （SEM） techniques. Ni-TiBE-Dy2O3 composite coatings showed higher microhardness, lower wear mass loss and friction coefficient compared with those of the pure Ni coating and Ni-TiB2 composite coatings. The wear mass loss of Ni-TiB2-Dy2O3 composite coatings was 9 and 1.57 times lower than that of the pure Ni coating and Ni-TiB2 composite coatings, respectively. The friction coefficient of pure Ni coating, Ni-TiB2 and Ni-TiB2-Dy2O3 composite coatings were 0.723, 0.815 and 0.619, respectively. Ni-TiBE-Dy2O3 composite coatings displayed the least friction coefficient among the three coatings. Dy2O3 particles in composite coatings might serve as a solid lubricant between contact surfaces to decrease the friction coefficient and abate the wear of the composite coatings. The loading-bearing capacity and the wear-reducing effect of the Dy2O3 particles were closely related to the content of Dy2O3 particles in the composite coatings.
基金Project(51501092)supported by the National Natural Science Foundation of ChinaProject(30915011332)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(2014M550292)supported by China Postdoctoral Science Foundation
文摘A kind of Al-TiB2/TiC in situ composite with a homogenous microstructure was successfully prepared through in situ reaction of pure Ti and Al-B-C alloy with molten aluminum.In order to improve the distribution of the particles and mechanical properties of the composites,subsequent hot rolling with increasing reduction was carried out.The microstructure evolution of the composites was characterized using field emission scanning electron microscopy(FESEM)and the mechanical properties were studied through tensile tests and microhardness measurement.It is found that both the microstructure uniformity and mechanical properties of the composites are significantly improved with increasing rolling reduction.The ultimate tensile strength and microhardness of the composites with90%rolling reduction reach185.9MPa and HV59.8,respectively,140%and35%higher than those of as-cast ones.Furthermore,the strengthening mechanism of the composite was analyzed based on the fracture morphologies.
基金Beijing Municipal Natural Science Foundation(52101003)The 9th Graduate Science Foundation of Beijing University of Technology(ykj-2011-6175)
文摘TiB2-Ni composite powders were prepared by pressurized hydrogen reduction cladding with different proportion of TiB2.The coatings were then prepared by APS.The microstructures and the phase composition of the powders as well as the deposited coatings were analyzed by scanning electron microscopy(SEM)and X-ray diffraction(XRD).The coatings were tested using a ring-on-disc tribometer from ambient temperature to 300°C.A sprayed Cr3C2-NiCr coating was tested as a reference.The morphologies of the worn surface of the coatings were observed and analyzed.It is found that the TiB2-Ni composite coatings present higher friction coefficient than that of the Cr3C2-NiCr coating at room temperature due to the adhesive wear mechanism,whereas the main wear mechanism of Cr3C2-NiCr coating is rupture and exfoliation.However,at high temperature,the friction coefficient of the TiB2-Ni composite coating decreases as a result of B2O3 solid lubricant,which alleviates the adhesive wear on coatings.Furthermore,the TiB2-Ni composite coating greatly reduces the mass loss of the boron cast iron.
基金National Natural Science Foundations of China(51045004)
文摘TiB2/TiB/TiNx(x=1,0.3)/Ti composite coating was prepared on pure Ti by laser surface alloying by using powders of boron as starting materials.The composite coating was examined by X-ray diffraction(XRD),high-resolution transmission electron microscopy(HRTEM)and scanning electron microscopy(SEM).The friction and wear properties of the composite coating were examined using a pin-on-disk tester under dry sliding wear condition.The results showed that the top surface of the composite coating was mainly composed of TiB2,TiB,TiN0.3,TiN and Ti phases,while the interface of the composite coating was composed of TiB and Ti phases.The composite coating showed sticklike structure near the top surface,and dendrites structure near the interface.The friction and wear test showed that the composite coating had better wear resistance than pure Ti due to their higher microhardness than that of pure Ti substrate.
基金supported by Basic Science Research Project of Colleges and Universities in Liaoning Province in China (No. LG201714)。
文摘Lightweight hybrid structures of Al MMCs and titanium alloy dissimilar materials have great prospect in the defence industry application. So, it is necessary to join Al MMCs with Ti metal to achieve this structural design. In this work, in-situ Ti B_(2)/7050 composite and TA2 were firstly attempted to join by TIG welding-brazing technique. The result was that the intact welding-brazing butt joint was successfully fabricated. The joint presents dual characteristics, being a brazing on TA2 side and a welding on Ti B_(2)/7050 side. At brazing joint side, ER4043 filler metal effectively wets on TA2 under TIG heating condition,and a continuous interfacial reaction layer with 1 e3 mm is formed at welded metal/TA2 interface. The whole interfacial reaction layers are composed of Ti(Al Si)3 intermetallic compounds(IMCs), but their morphologies at the different regions present obvious distinguishes. The microhardness of the reaction layers is as much as 141 e190 HV. At welding joints side, the fusion zone appears the equixaed crystal structure, and the grain sizes are much smaller than those of welded metal, which is attributed to the effect of Ti B2 particulates from the melted Ti B_(2)/7050 on acceleration formation and inhibiting growth for the new crystal nucleus. The tensile test results show that average tensile strength of the optimal welding-brazing joint is able to achieve 138 MPa. The failure of the tensile joint occurs by quasi-cleavage pattern, and the cracks initiate from the IMCs layer at the groove surface of TA2 and propagate into the welded metal.
基金financially supported by the National Natural Science Foundation of China(Nos.51072104 and 51272141)Tai Shan Scholars Project of Shandong Province,China(No.ts20110828)
文摘The NiAl–TiC–TiB2 composites were processed by self-propagating high-temperature synthesis（SHS） method using raw powders of Ni, Al, Ti, B4 C, TiC, and TiB2, and their microstructure and micro-hardness were investigated. The TiC–TiB2 in NiAl matrix, with contents from 10 to 30 wt%, emerged with the use of two methods： in situ formed and externally added. The results show that all final products are composed of three phases of NiAl, TiC, and TiB2. The microstructures of NiAl–TiC–TiB2 composites with in situ-formed TiC and TiB2 are fine, and all the three phases are distributed uniformly. The grains of NiAl matrix in the composites have been greatly refined, and the micro-hardness of NiAl increases from 381 HV100 to 779 HV100. However, the microstructures of NiAl–TiC–TiB2 composites with externally added TiC and TiB2 are coarse and inhomogeneous, with severe agglomeration of TiC and TiB2 particles. The samples containing externally added 30 wt% TiC–TiB2attain the micro-hardness of 485 HV100. The microstructure evolution and fracture mode of the two kinds of NiAl–TiC–TiB2 composites are different.
基金Project (2005CB623703) supported by the Major State Basic Research and Development Program of ChinaProject (2008AA030502) supported by the National High-Tech Research and Development Program of China
文摘Pitch and TiB2/C green composite cathode material were respectively analyzed with simultaneous DSC-TGA, and effects of three baking processes of TiB2/C composite cathode material, i.e. K25, K5 and M5, on properties of TiB2/C composite cathode material were investigated. The results show that thermogravimetrie behavior of pitch and TiB2/C green composite cathode is similar, and appears the largest mass loss rate in the temperature range from 200 to 600 ℃. The bulk density variation of sample K5 before and after baking is the largest （11.9%）, that of sample K25 is the second, and that of sample M5 is the smallest （6.7%）. The crushing strength of sample M5 is the biggest （51.2 MPa）, that of sample K2.5 is the next, and that of sample K5 is the smallest （32.8 MPa）. But, the orders of the electrical resistivity and electrolysis expansion of samples are just opposite with the order of crushing strength. The heating rate has a great impact on the microstructure of sample. The faster the heating rate is, the bigger the pore size and porosity of sample are. Compared with the heating rate between 200 and 600℃ of samples K25 and K5, that of sample M5 is slower and suitable for baking process of TiB2/C composite cathode material.
